Hoist Fitness RS-1501 User Manual
RS-1501
SHOULDER PRESS
Note: Both Serial Number and Model Number are Required when Ordering Parts
Customer Service
(800) 548-5438
(858) 578-7676
Fax
(858) 578-9558
OWNER'S MANUAL
RECORD SERIAL NUMBER HERE
CATALOG NUMBER
0406 - 015
OWNER'S MANUAL
CONTENTS
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
MAINTENANCE SCHEDULE.................................................
02
04
14
15
16
17
19
20
22
24
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
WEIGHT RATIOS....................................................................
EXERCISE LOG......................................................................
LIMITED WARRANTY............................................................
25
28
29
30
31
PAGE 01
RS-1501 ASSEMBLY
OWNER'S MANUAL
INSTRUCTIONS
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
TOOLS REQUIRED
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
RS-1501 ASSEMBLY
PAGE 02
OWNER'S MANUAL
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
PAGE 03
RS-1501 ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
ALTERNATIVE WIEGHT CAGE POSITION
ALTERNATE POSITION
THE ROC-IT WEIGHT CAGE IS DESIGNED TO BE INSTALLED ON EITHER THE
LEFT OR RIGHT SIDE OF THE RS-1501 IN ORDER TO ACCOMADATE THE USER.
RS-1501 ASSEMBLY
PAGE 04
OWNER'S MANUAL
FRAME ASSEMBLY
*ASSEMBLE WEIGHT CAGE FIRST*
ENSURE THE USE OF
"WEIGHT STACK #1"
CIRCUIT STACK
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
53
50
57
62
64
64 6
65
15
53
57
57
58
PAGE 05
37
15
136 1/16" 3456
RS-1501 ASSEMBLY
27
52
57
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- HAND TIGHTEN HARDWARE.
- WRENCH TIGHTEN ALL HARDWARE FROM
PREVIOUS STEPS.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
57
58
58
8
57
1
57 58
58
57
15
34
58
57
16
57
17
57
53
53
RS-1501 ASSEMBLY
PAGE 06
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE (55 & 60) THEN
LOOSEN NUT JUST ENOUGH FOR(2 & 50) TO
PIVOT FREELY.
- WRENCH TIGHTEN ALL OTHER HARDWARE.
- WRENCH TIGHTEN ALL HARDWARE FROM
PREVIOUS STEPS.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
2
35
19
58
57
PAGE 07
57
55
1
RS-1501 ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
WARNING - CABLE BOLT MUST BE THREADED
A MINIMUM OF 3/8" WITH JAM NUT TIGHTENED
SECURELY TO ENSURE PROPER CONNECTION.
LIGHT CABLING OPTION
60
64
61
64
NOTE:
- WRENCH TIGHTEN ALL OTHER HARDWARE.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
FINE TUNING:
LOOSEN JAM NUT AND THREAD
BOLT IN/OUT TO GIVE THE CABLE
PROPER TENSION. RE-T IGHTEN
JAM NUT.
64
65
64
65
60
50
64
50
18
15
64
65
RS-1501 ASSEMBLY
PAGE 08
OWNER'S MANUAL
FRAME ASSEMBLY
WARNING - CABLE BOLT MUST BE THREADED
A MINIMUM OF 3/8" WITH JAM NUT TIGHTENED
SECURELY TO ENSURE PROPER CONNECTION.
HEAVY CABLING OPTION
NOTE:
- WRENCH TIGHTEN ALL OTHER HARDWARE.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
FINE TUNING:
LOOSEN JAM NUT AND THREAD
BOLT IN/OUT TO GIVE THE CABLE
PROPER TENSION. RE-T IGHTEN
JAM NUT.
20
60
64
64
65
15
5075
18
20
74
PAGE 09
60
64
64
75
65
RS-1501 ASSEMBLY
Loading...