Hoist Fitness RS-1402-A User Manual

RS-1402-A

LEG CURL

**WARNING!**

TO PREVENT POSSIBLE TIPPING, BOLT THIS UNIT TO THE

EXERCISE FLOOR. FAILURE TO DO SO MAY RESULT IN SERIOUS

INJURY OR DEATH.

Note: Both Serial Number and Model Number are Required when Ordering Parts

RECORD SERIAL NUMBER HERE

MACHINE CODE

OWNER'S MANUAL

A04

Customer Service

[phone]
[phone]

Fax

[phone]

OWNER'S MANUAL

CONTENTS

INSTRUCTIONS .....................................................................

FRAME ASSEMBLY ..............................................................

PRE-ASSEMBLY....................................................................

DECAL PLACEMENT.............................................................

DECAL REFERENCE.............................................................

PART LIST...............................................................................

ABBREVIATIONS...................................................................

BOLT SIZING CHART............................................................

WASHER SIZING CHART......................................................

MAINTENANCE SCHEDULE.................................................

02

04

23

24

25

27

31

32

34

36

GENERAL MAINTENANCE INFORMATION........................

WEIGHT TRAINING TIPS.......................................................

WEIGHT RATIOS....................................................................

EXERCISE LOG......................................................................

37

38

39

40

41LIMITED WARRANTY............................................................

PAGE 01

RS-1402-A ASSEMBLY

OWNER'S MANUAL

INSTRUCTIONS

Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.

HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.

TOOLS REQUIRED

Ratchet Wrench

1/2", 9/16" and 3/4" Sockets

Adjustable Wrench

Rubber Mallet

Tape Measure

Level

Hex Key Wrench Set

Two People

RS-1402-A ASSEMBLY

PAGE 02

OWNER'S MANUAL

***THIS PAGE WAS INTENTIONALLY LEFT BLANK***

RS-1402-A ASSEMBLYPAGE 03

OWNER'S MANUAL

FRAME ASSEMBLY

RS-1402-A ASSEMBLY

PAGE 04

OWNER'S MANUAL

FRAME ASSEMBLY

*ASSEMBLE WEIGHT CAGE FIRST*

NOTE:

- WRENCH TIGHTEN HARDWARE (90).

- HAND TIGHTEN ALL OTHER HARDWARE.

- INSTALL CABLE AND PULLEYS AT THE

102

SAME TIME.

- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

ENSURE THE USE OF WEIGHT
STACK #4 WITH STAND OFFS.

81

75

74

90

74

75

98

30

20

20

PAGE 05

80

156 3/4" 3981

RS-1402-A ASSEMBLY

92

11

102

OWNER'S MANUAL

FRAME ASSEMBLY

NOTE:

- HAND TIGHTEN HARDWARE.

- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.

- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

75

61

75

81

81

75

4

80

74

81

75

74

87

115

65

75

95

68

75

96

RS-1402-A ASSEMBLY PAGE 06

OWNER'S MANUAL

FRAME ASSEMBLY

STEP 1

112

111

NOTE:

- WRENCH TIGHTEN HARDWARE.

- WRENCH TIGHTEN ALL PREVIOUSLY
HAND TIGHTENED HARDWARE.

- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

6

53

4

STEP 2

PROPERLY INSTALLED VIEW

NOTE:

BE SURE BOLT (93) IS INSTALLED SO
BOLT HEAD FITS INTO HEX BOLT LOCK,
AS SHOWN.

81

75

5

93

4

PAGE 07

RS-1402-A ASSEMBLY

OWNER'S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARDWARE.

2

- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

112

111

6

NOTE:

BE SURE BOLT (93) IS INSTALLED SO
BOLT HEAD FITS INTO HEX BOLT LOCK,
AS SHOWN.

81

93

75

53

PROPERLY INSTALLED VIEW

RS-1402-A ASSEMBLY PAGE 08

OWNER'S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARDWARE.

- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

81

75

10

4

95

NOTE:

BE SURE BOLT (95) IS INSTALLED SO
BOLT HEAD FITS INTO HEX BOLT LOCK,
AS SHOWN.

PAGE 09

PROPERLY INSTALLED VIEW

RS-1402-A ASSEMBLY

OWNER'S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARDWARE.

- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

93

12

22

75

81 75

81

10

2

NOTE:

BE SURE BOLT (93) IS INSTALLED SO
BOLT HEAD FITS INTO HEX BOLT LOCK,
AS SHOWN.

PROPERLY INSTALLED VIEW

RS-1402-A ASSEMBLY PAGE 10

OWNER'S MANUAL

FRAME ASSEMBLY

NOTE:

- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

CABLE PROFILE VIEW

FROM WEIGHT STACK

20

NOTE:

BE SURE CABLE RUNS
BETWEEN THE PULLEYS AND
GUARD PINS AS SHOWN.

PAGE 11 RS-1402-A ASSEMBLY

87

OWNER'S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARDWARE.

- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.

- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.

87

74

74

NOTE:

BE SURE CABLE RUNS
BETWEEN THE PULLEY AND
GUARD PIN AS SHOWN.

2

20

45

74

80

30

74

NOTE:

BE SURE CABLE RUNS
BETWEEN THE PULLEY AND
GUARD PIN AS SHOWN.

RS-1402-A ASSEMBLY

80

30

PAGE 12