Hoist Fitness RS-1302 User Manual
RS-1302
PEC FLY
Note: Both Serial Number and Model Number are Required when Ordering Parts
Customer Service
(800) 548-5438
(858) 578-7676
Fax
(858) 578-9558
OWNER'S MANUAL
RECORD SERIAL NUMBER HERE
CATALOG NUMBER
0108 - 000
OWNER'S MANUAL
CONTENTS
INSTRUCTIONS .....................................................................
ALTERNATE POSITION.........................................................
FRAME ASSEMBLY ..............................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
02
04
05
30
31
32
33
36
37
39
MAINTENANCE SCHEDULE.................................................
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
WEIGHT RATIOS....................................................................
EXERCISE LOG......................................................................
LIMITED WARRANTY............................................................
41
42
43
44
45
46
PAGE 01
RS-1302 ASSEMBLY
OWNER'S MANUAL
INSTRUCTIONS
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
TOOLS REQUIRED
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
Two People Required for Assembly
RS-1302 ASSEMBLY
PAGE 02
OWNER'S MANUAL
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
PAGE 03
RS-1302 ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
ALTERNATE WEIGHT CAGE POSITION
THE ROC-IT WEIGHT CAGE IS DESIGNED TO BE INSTALLED ON EITHER
LEFT OR RIGHT SIDE OF THE RS-1302 IN ORDER TO ACCOMODATE THE USER.
RS-1302 ASSEMBLY
ALTERNATE POSITION
PAGE 04
OWNER'S MANUAL
FRAME ASSEMBLY
ENSURE THE USE OF WEIGHT
STACK #2 W/ STANDOFFS
NOTE:
- HAND TIGHTEN HARDWARE.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
80
29
68
56
2
14
56
78
29
66
56
78
72
59
59
79
56
2
PAGE 05
156" 3962
RS-1302 ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
STOP.
INSTALL WEIGHT STACK SHIELDS BEFORE STARTING
THIS STEP. REFER TO ROC-IT WEIGHT CAGE MANUAL FOR
SPECIFIC INSTRUCTIONS ON SHIELD INSTALLATION.
WEIGHT STACK SHIELDS
63
57
56
49
79
59
80
15
46
59
71
64
56
79
59
RS-1302 ASSEMBLY
14
11
52
36
59
78
56
72
PAGE 06
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE (76) THEN
LOOSEN NUT JUST ENOUGH FOR (12)
TO PIVOT FREELY.
- WRENCH TIGHTEN ALL HARDWARE FROM
PREVIOUS STEPS.
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.
12
79
59
37
11
PAGE 07
59
76
RS-1302 ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- INSTALL CABLE AND PULLYES AT THE
SAME TIME.
78
56
29
11
56
65
RS-1302 ASSEMBLY
PAGE 08
OWNER'S MANUAL
FRAME ASSEMBLY
WARNING - CABLE BOLT MUST BE THREADED
A MINIMUM OF 3/8" WITH JAM NUT TIGHTENED
SECURELY TO ENSURE PROPER CONNECTION.
LIGHT CABLING OPTION
NOTE:
- WRENCH TIGHTEN HARDWARE (66) THEN
LOOSEN NUT JUST ENOUGH FOR (42) TO
PIVOT FREELY.
- WRENCH TIGHTEN OTHER HARDWARE.
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.
FINE TUNING:
LOOSEN JAM NUT AND THREAD
BOLT IN/OUT TO GIVE THE CABLE
PROPER TENSION. RE-T IGHTEN
JAM NUT.
65
56
66
29
56
56
78
56
12
78
26
26
42
2
JAM NUT
CABLE BOLT
PAGE 09
RS-1302 ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
HEAVY CABLING OPTION
NOTE:
- WRENCH TIGHTEN HARDWARE.
- INSTALL CABLE AND PULLYES AT THE
SAME TIME.
77
39
26
42
26
43
39
77
11
RS-1302 ASSEMBLY
PAGE 10
OWNER'S MANUAL
FRAME ASSEMBLY
WARNING - CABLE BOLT MUST BE THREADED
A MINIMUM OF 3/8" WITH JAM NUT TIGHTENED
SECURELY TO ENSURE PROPER CONNECTION.
HEAVY CABLING OPTION
NOTE:
- WRENCH TIGHTEN HARDWARE.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.
FINE TUNING:
LOOSEN JAM NUT AND THREAD
BOLT IN/OUT TO GIVE THE CABLE
PROPER TENSION. RE-T IGHTEN
JAM NUT.
CABLE BOLT
JAM NUT
78
42
56
65
56
29
PAGE 11
RS-1302 ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- REPEAT STEPS FOR OPPOSITE
SIDE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
78
63
56
10
12
56
17
56
78
RS-1302 ASSEMBLY
56
63
PAGE 12
OWNER'S MANUAL
CABLING PROFILE
FRAME ASSEMBLY
BE SURE CABLE IS POSITIONED
BETWEEN GUARD PINS AND PULLEYS
AS SHOWN.
NOTE:
- WRENCH TIGHTEN HARDWARE.
- INSTALL CABLE AND PULLEY AT THE
SAME TIME.
- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.
PROPERLY INSTALLED VIEW
29
78 58
11
58
69
1
7
PAGE 13
RS-1302 ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
BE SURE CABLE IS POSITIONED
BETWEEN GUARD PINS AND PULLEYS
AS SHOWN.
PROPERLY INSTALLED VIEW
78
56
NOTE:
- WRENCH TIGHTEN HARDWARE.
- INSTALL CABLE AND PULLEY AT THE
SAME TIME.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
29
1
11
56
66
RS-1302 ASSEMBLY
PAGE 14
Loading...