Hoist Fitness RPL-5301 User Manual
RPL-5301
OWNER'S MANUAL
ADDENDUM
READ THIS FIRST!
THE FOLLOWING PAGES WILL SUPERCEDE THE
EXISTING PAGES IN THE RPL-5301 MANUAL
CATALOG NUMBER 0208-002
JULY, 2008
Note: Both Serial Number and Model Number are Required when Ordering Parts
Customer Service
RECORD SERIAL NUMBER HERE
RPL-5301 ADDENDUM
(800) 548-5438
(858) 578-7676
(858) 578-9558
Fax
OWNER'S MANUAL
MACHINE ADJUSTMENT
MAJOR ADJUSTMENT:
LOOSEN JAM NUTS (26, 27) AND TWIST TIE RODS (16)
IN/OUT TO ADJUST THE PRESS ARMS TO THE PROPER
HEIGHT. ONCE THE PROPER HEIGHT IS REACHED AND
THE PRESS ARMS ARE OF EQUAL HEIGHTS, BE SURE
TO RE-TIGHTEN JAM NUTS.
27
16 16
27
TWIST THE TIE RODS (16) EITHER
- CLOCKWISE TO DECREASE
PRESS ARM HEIGHT
OR
- COUNTER-CLOCKWISE TO
INCREASE PRESS ARM HEIGHT.
26
RPL-5301 ASSEMBLY
26
34 1/4"
w/o RUBBER FOOT
34 1/2"
w/ RUBBER FOOT
PAGE 26
RPL-5301
PLATE-LOADED CHEST PRESS
**WARNING !**
TO PREVENT POSSIBLE TIPPING, BOLT THIS UNIT TO THE
EXERCISE FLOOR. FAILURE TO DO SO MAY RESULT IN SERIOUS
INJURY OR DEATH.
Note: Both Serial Number and Model Number are Required when Ordering Parts
Customer Service
(800) 548-5438
(858) 578-7676
Fax
(858) 578-9558
OWNER'S MANUAL
RECORD SERIAL NUMBER HERE
CATALOG NUMBER
0208 - 003
OWNER'S MANUAL
CONTENTS
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
MACHINE ADJUSTMENT......................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
02
04
26
28
29
30
33
36
37
39
MAINTENANCE SCHEDULE.................................................
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
EXERCISE LOG......................................................................
LIMITED WARRANTY............................................................
41
42
43
44
45
PAGE 01
RPL-5301 ASSEMBLY
OWNER'S MANUAL
INSTRUCTIONS
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
TOOLS REQUIRED
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
Two People
RPL-5301 ASSEMBLY
PAGE 02
OWNER'S MANUAL
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
PAGE 03
RPL-5301 ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
RPL-5301 ASSEMBLY
PAGE 04
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
3
10
74
2
28
59
9
50
49
PAGE 05
59
83
RPL-5301 ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
47
12
15
58
60
72
72
60
58
12
47
RPL-5301 ASSEMBLY
PAGE 06
OWNER'S MANUAL
FRAME ASSEMBLY
15
NOTE:
- WRENCH TIGHTEN HARDWARE.
69
58
8
63
32
9
58
82
PAGE 07
RPL-5301 ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
STEP 1:
STEP 2:
3
- POSITION (13) IN BETWEEN
ITEMS (2 & 3)
- ROTATE (13) UPWARD
INTO PLACE
3
13
2
3
83
59
13
13
77
59
83
59
37
77
59
9
RPL-5301 ASSEMBLY
PAGE 08
83
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- HAND TIGHTEN HARDWARE.
59
13
59
80
PAGE 09
RPL-5301 ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
76
59
36
NOTE:
- WRENCH TIGHTEN HARDWARE.
- WRENCH TIGHTEN ALL PREVIOUSLY
HAND TIGHTENED HARDWARE.
59
83
2
3
RPL-5301 ASSEMBLY
PAGE 10
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- REPEAT ASSEMBLY FOR OPPOSITE SIDE.
58
70
70
58
58
5
82
58
11
7
58
58
82
82
PAGE 11
70
RPL-5301 ASSEMBLY
81
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
11
59
38
9
59
83
RPL-5301 ASSEMBLY
PAGE 12
Loading...