Hoist Fitness HS-OPT-03 User Manual

HS-OPT-03

PERSONAL PULLEY UPGRADE

Note: Both Serial Number and Model Number are Required when Ordering Parts

Customer Service

[phone]
[phone]

Fax

[phone]

OWNER'S MANUAL

RECORD SERIAL NUMBER HERE

CATALOG NUMBER

0407 - 003

OWNER'S MANUAL

CONTENTS

INSTRUCTIONS .....................................................................

FRAME ASSEMBLY ..............................................................

DECAL PLACEMENT.............................................................

DECAL REFERENCE.............................................................

PART LIST...............................................................................

ABBREVIATIONS...................................................................

BOLT SIZING CHART............................................................

WASHER SIZING CHART......................................................

MAINTENANCE SCHEDULE.................................................

GENERAL MAINTENANCE INFORMATION........................

02

04

08

09

10

11

12

14

16

17

WEIGHT TRAINING TIPS.......................................................

EXERCISE LOG......................................................................

LIMITED WARRANTY............................................................

18

19

20

PAGE 01

HS-OPT-03 ASSEMBLY

OWNER'S MANUAL

INSTRUCTIONS

Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.

HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.

TOOLS REQUIRED

Ratchet Wrench

1/2", 9/16" and 3/4" Sockets

Adjustable Wrench

Rubber Mallet

Tape Measure

Level

Hex Key Wrench Set

HS-OPT-03 ASSEMBLY

PAGE 02

OWNER'S MANUAL

***THIS PAGE WAS INTENTIONALLY LEFT BLANK***

PAGE 03

HS-OPT-03 ASSEMBLY

OWNER'S MANUAL

FRAME ASSEMBLY

NOTE:

- POSITION EACH HS-1175 AS SHOWN IN
THE DIAGRAM BELOW FOR PROPER
ALLIGNMENT BEFORE INSTALLING HS-OPT-03.

18 18

39 3/4" 1009

HS-OPT-03 ASSEMBLY

57 5/8" 1464

PAGE 04

11

10

OWNER'S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARDWARE.

15

13

*

7

- THIS HARDWARE WAS PREVIOUSLY INSTALLED

*

IN THE ASSEMBLY OF THE HS-1175. IN ORDER TO
INSTALL (3) YOU MUST FIRST REMOVE THIS
HARDWARE.

- DISCARD BOLTS FROM HS-1175 AND USE THOSE
THAT WERE INCLUDED WITH THE HS-OPT-03.

*

3

10

13

12

14

PAGE 05

HS-OPT-03 ASSEMBLY

OWNER'S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARDWARE.

- THIS HARDWARE WAS PREVIOUSLY INSTALLED

*

IN THE ASSEMBLY OF THE HS-1175. IN ORDER TO
INSTALL (2) YOU MUST FIRST REMOVE THIS
HARDWARE.

- DISCARD BOLTS FROM HS-1175 AND USE THOSE
THAT WERE INCLUDED WITH THE HS-OPT-03.

* *

*

*

2

NOW THAT THE HS-OPT-03 IS COMPLETELY ASSEMBLED TAKE TIME TO ASSURE THAT
YOUR UNIT IS ASSEMBLED SQUARE AND PERPENDICULAR. IT MAY BE NECESSARY TO
LOOSEN SOME FRAME HARDWARE TO RE-ALIGN THE FRAME AND RETIGHTEN BOLTS.

HS-OPT-03 ASSEMBLY

*IMPORTANT*

PAGE 06