Hoist Fitness HD‐3700 User Manual

HD‐3700

CHINDIPASSIST

**WARNING!**

TOPREVENTPOSSIBLETIPPING,BOLTTHISUNITTOTHE

EXERCISEFLOOR.FAILURETODOSOMAYRESULTINSERIOUS

INJURYORDEATH.

A00

OWNER’S MANUAL

CONTENTS

INSTRUCTIONS……………………………..…………………...

FRAME ASSEMBLY……………………..………..………….…

PRE-ASSEMBLY………………………………..……………….

DECAL PLACEMENT……………………….....………………..

DECAL REFERENCE………………...........….………….…….

PART LIST…………………………..……….…….…………..…

ABBREVIATIONS……………………..……….………….……..

BOLT SIZING CHART…………………………………………...

WASHER SIZING CHART…………….….…….……………....

MAINTANENCE SCHEDULE…………..………….………..….

02

04

33

35

36

39

43

44

50

52

GENERAL MAINTANENCE INFORMATION.............…….…

WEIGHT TRAINING TIPS…………………….……….………..

EXERCISE LOG…………………………………..……………...

LIMITED WARRANTY…………………………..……………….

53

54

55

56

PAGE 01 HD-3700 ASSEMBLY

OWNER’S MANUAL

INSTRUCTIONS

Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.

HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.

TOOLS REQUIRED

Ratchet Wrench

1/2", 9/16" and 3/4" Sockets

Adjustable Wrench

Rubber Mallet

Tape Measure

Level

SAE Hex Key Wrench Set

Two People

HD-3700 ASSEMBLY PAGE 02

OWNER’S MANUAL

***THIS PAGE WAS INTENTIONALLY LEFT BLANK***

PAGE 03 HD-3700 ASSEMBLY

OWNER’S MANUAL

FRAME ASSEMBLY

HD-3700 ASSEMBLY PAGE 04

OWNER’S MANUAL

CABLE PROFILE VIEW

3031/8”LG.[7700mm]

PAGE 05 HD-3700 ASSEMBLY

OWNER’S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARDWARE

- INSTALL CABLES AND PULLEYS AT
THE SAME TIME.

- SOME PARTS MAY HAVE BEEN REMOVED

FOR CLARITY.

NOTE:

BE SURE TO POSITION CABLE (1)
BETWEEN PULLEY (29) AND CABLE
GUARD (12) AS SHOWN

PROPERLYINSTALLEDVIEW

HD-3700 ASSEMBLY PAGE 06

OWNER’S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARWARE

- SOME PARTS MAY HAVE BEEN REMOVED

FOR CLARITY.

PAGE 07 HD-3700 ASSEMBLY

OWNER’S MANUAL

FRAME ASSEMBLY

NOTE:

- HAND TIGHTEN HARDWARE

- WRENCH TIGHTEN HARDWARE (82)

- INSTALL CABLES AND PULLEYS AT

THE SAME TIME

- SOME PARTS MAY HAVE BEEN REMOVED

FOR CLARITY.

HD-3700 ASSEMBLY PAGE 08

OWNER’S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARDWARE.

- SOME PARTS MAY HAVE BEEN REMOVED

FOR CLARITY.

WEIGHT STACK #21

INSTALL BOLT INTO SECOND
WEIGHT PLATE FROM THE TOP

STEP1STEP2

PAGE 09 HD-3700 ASSEMBLY

OWNER’S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARDWARE.

- INSTALL CABLES AND PULLEYS AT
AT THE SAME TIME

- SOME PARTS MAY HAVE BEEN REMOVED

FOR CLARITY.

NOTE:

BE SURE TO POSITION CABLE (1)
BETWEEN PULLEYS (29) AND
GUARD PINS AS SHOWN

GUARD PINS

HD-3700 ASSEMBLY PAGE 10

OWNER’S MANUAL

FRAME ASSEMBLY

NOTE:

- HAND TIGHTEN HARDWARE

- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.

PAGE 11 HD-3700 ASSEMBLY

OWNER’S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARDWARE.

- WRENCH TIGHTEN ALL PREVIOUSLY
HAND TIGHTENED HARDWARE

- SOME PARTS MAY HAVE BEEN REMOVED

CABLE END

FOR CLARITY.

JAMNUT

LANYARD

RING

HD-3700 ASSEMBLY PAGE 12

OWNER’S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARDWARE

- SOME PARTS MAY HAVE BEEN REMOVED

FOR CLARITY.

PAGE 13 HD-3700 ASSEMBLY

OWNER’S MANUAL

NOTE:

- WRENCH TIGHTEN HARDWARE

- SOME PARTS MAY HAVE BEEN REMOVED
FOR CLARITY.

HOIST RECOMMENDS THE TOWEL HANGER
BE INSTALLED ON THE SIDE OF THE WEIGHT
CAGE MOST CONVIENIENT FOR THE END USER

FRAME ASSEMBLY

*IMPORTANT*

ATTHISSTEP,TAKE TIMETOASSURETHATYOURUNITISASSEMBLED

SQUAREANDPERPENDICULAR.USEALEVELTOCHECKTHATTHEGUIDERODSARE

PERPENDICULARINBOTHDIRECTIONS.IFTHEYARENOTPERPENDICULARINBOTHDIRECTIONS,

ITWILLBENECCESSARYTOLOOSENSOMEFRAMEHARDWARETORE‐ALIGNTHEFRAMEAND

RETIGHTENBOLT

HD-3700 ASSEMBLY PAGE 14

S.

OWNER’S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARDWARE. (85)

- INSTALL CABLES AND PULLEYS AT
AT THE SAME TIME

- SOME PARTS MAY HAVE BEEN REMOVED

FOR CLARITY.

PAGE 15 HD-3700 ASSEMBLY

OWNER’S MANUAL

FRAME ASSEMBLY

NOTE:

- WRENCH TIGHTEN HARDWARE

- INSTALL CABLES AND PULLEYS
AT THE SAME TIME

- SOME PARTS MAY HAVE BEEN REMOVED

FOR CLARITY.

HD-3700 ASSEMBLY PAGE 16

OWNER’S MANUAL

FRAME ASSEMBLY

NOTE:

- HAND TIGHTEN HARDWARE.

- SOME PARTS MAY HAVE BEEN REMOVED

FOR CLARITY.

PAGE 17 HD-3700 ASSEMBLY