Hogtunes 352F-AA, 356F, 356R Installation Manual

HOGTUNES

Audio Solutions For The Great American Cruiser

Designed and Engineered in Canada

Technical Stuff

Power Handling: 100 RMS‐150 Peak
Frequency Response: 55hz‐25Khz
Front. Speaker Sensitivity: 92 db 1watt/1meter
Rear. Speaker Sensitivity: 91 db 1watt/1meter
Impedance 98‐05: 6 Ohms
Nom. Impedance 2006‐13: 2 Ohms
Cool Factor: EXTREME

www.hogtunes.com

Replacement Speaker

Installation Manual

Rev 1.0

Models 352F‐AA and 352R‐AA (2Ω) for 2006‐2013 Bikes With Factory

“Advanced Audio” Radios or 1998‐2013 Bikes With

2 Ohm Stable Amplifiers

Models 356F and 356R (6Ω) for 1998‐2005 Bikes With Factory Radios

or 1998‐2013 Bikes With Aftermarket Car Radios

Any audio system can be a distraction to the rider

and/or passenger. Please use caution when

playing your stereo, especially in traffic.

Models 352F‐AA/352R‐AA/356F/356R

Congratulations and Thank‐you for your purchase of Hogtunes speakers!
Since positive word of mouth is the best way to grow our business, we want
your new speakers to work as well as they were designed to. If you have any
questions or concerns, we are here to help. Email [e-mail], or call us
during regular business hours (EST) at 705‐719‐6361. If you still need help, then
please consider a professional installation by your dealer.

Front Speaker Installation Instructions:

Step #1: Make sure your ignition switch stays in the “OFF” position. Remove
your outer fairing/headlamp assembly, and set aside. Refer to a service
manual if you need help with this. It’s always a good idea to have a towel or
something similar on your front fender to avoid dings or scratches if
anything is dropped—this can and most likely will happen!

Step #2: Take the 2 wires off each speaker by gently pulling one at a time.
Undo the screws that attach each speaker/grill assembly to the inner fairing
and remove. Gently pull the stock speaker out of each grill assembly.

Step #3: “Clip” the Hogtunes speaker into each grill assembly. Position your
new speaker/grill assembly onto the inner fairing and re‐attach each one us‐
ing the OE screws. A hand screwdriver is recommended for this step.

Step #4:

Hogtunes speakers are a direct replacement for the OE speakers.
The female OE “in‐line” connectors mate with the male connectors on each
speaker and only go on one way. If you are replacing previously installed
aftermarket speakers you may need to re‐install the correct sized connectors
(not supplied) onto the factory speaker wires. The number 1 reason for tech
support calls is due to loose connections at the speaker. Please make sure
you have a very good connection to avoid this.

Step #5: Once you are confident the factory wires are correctly attached to
the new speakers, turn on your radio to confirm that both speakers are
playing. Re‐install your fairing/headlamp assembly. Your new G3 Hogtunes
speakers are ready to enjoy!

Rear Speaker “Pod” Installation Instructions

Step #1: Make sure your ignition switch stays in the “OFF” position.
Remove the factory speaker grills by undoing the 4 screws on the front of
the grills. Carefully lift up on each speaker and take the 2 wires off by
pulling one at a time from the stock speaker. Remove the speakers.

Step #2: Hogtunes rear speakers are a direct replacement for the OE
speakers. The female OE “in‐line” connectors mate with the male
connectors on each speaker, and only go on one way. If you are replacing
previously installed aftermarket speakers, you may need to re‐install the
correct sized connectors (not supplied) onto the factory speaker wires.
The number 1 reason for tech support calls is due to loose connections at
the speaker. Please make sure you have a very good connection to avoid
this. Once you are confident the factory wires are correctly attached to the
new speakers, sit them in place, put the grills back on, and secure the
speaker by reinstalling the 4 screws per grill. Note: The factory rubber
“nutserts” on the rear pod side can be finicky. It’s a good idea to get all 4
grill screws “started” and then get each one snug. Gradually tighten each
one down making sure all 4 screws holding the grill down are secure!

Step#3: Turn your radio on and confirm that both speakers are playing.
Your new G3 speakers are ready to enjoy!

Warranty Information:

Hogtunes speakers are warranted for a period of 20 years to the original
purchaser. Proof of purchase is required for all warranty claims. All Warranty
claims must be made through the dealer this product was originally purchased
from. Please contact them for warranty or return procedures. Products found
to be defective during the warranty period will be replaced (with a product
deemed to be equivalent) at Hogtunes sole discretion.

What Is Not Covered:

1) Any expense related to the removal or re‐installation of these speakers.

2) Repairs to these speakers performed by anyone other than Hogtunes Inc.

3) Subsequent damage to any other components.

4) Any product purchased from a non‐authorized Hogtunes dealer.

5) Damage to speakers from an accident or collision.

6) Damage from incorrect installation, improper use, abuse or modifications.

7) Damage to inbound product due to improper packing.

IMPORTANT Note for Road Glides: All 1998‐2003 and some 2004 Road Glides
require rubber shims (supplied in Hogtunes model 356F) that must go between
the front of the speaker and the factory grill. If installing the speakers into a
2004 model, please visit http://www.hogtunes.com/tech.html and click “Road
Glide Speaker Grill Fix” to see if you need these on your particular bike. You can
also request this by emailing us and asking for “Road Glide Speaker Grill Fix”.
If you have the “old” style factory grills and do not use the shims, damage to
the speakers will occur. This will not be covered by warranty.

IMPORTANT: Hogtunes 352F‐AA and 352R‐AA models are 2 ohms and will cause

damage if wired directly to 98‐05 factory radios built in power!