Page 1
Spec-00212
FRAME JOINING KITS
Permits joining two enclosure frames while maintaining an
I
763.422.2661
763.422.2588
NETWORKING
Free-Stand CabinetS
PrOLine™ aCCeSSOrieS
FREESTAND CABINETS PROL INE™ A ccEs sORI Es
environmental seal.
Side-to-Side Joining Kit consists of six frame nuts and screws, as
well as gasket material to maintain a dust-tight and water-tight seal
between ganged frames. Can be used if rack angles are not in the
front or rearmost positions or if a subpanel is not in the rearmost
position.
Alternate Joining Kit consists of three standoffs, six frame nuts
and screws, as well as gasket material. This kit facilitates frame
joining when rack angles are in the front or rearmost position, or if
a subpanel is in the rearmost position.
Front-to-Back Joining Kit permits front-to-back joining of two
single-bay enclosures. This kit does not fit 1200-mm or 1600-mm
wide frames.
Bulle tIn: p 20, p20eM
Catalog Number Description
PJ2F Standard Frame Joining, Side-to-Side
PJ2FD Standard Frame Joining, Side-to-Side, Non-gasketed
PJ2FHF2 EMC Standard Frame Joining, Side-to-Side
PJ2FF Alternate Frame Joining, Side-to-Side
PJ2FBF Frame Joining, Front-to-Back
EQUIPMENT PROTECTION SOLUTIONSSUBJECT TO CHANGE WITHOUT NOT ICENETWORKING1
Spec-00 212 I
Page 2
FREESTAND CABINETS PROL INE™ A ccEs sORI Es
L JOINING BRACKET
The L Joining Bracket, made of 10
gauge steel, is used in conjunction
with the standard joining kit as
additional support. Pictured
hardware is included.
Bulle tIn: p 20
Catalog Number Description
PJB2F L Joining Bracket
FRAME FEET
Four die-cast feet for use on the
bottom of PROLINE™ frames that
raise the frame 9 mm.
Bulle tIn: p 20
Catalog Number Description
PFFM12 Frame Feet
TOOLLESS (SNAPIN) BLANKING PANELS FOR 19IN. RACKS
These Tool-less 19-in. Blanking
Panels provide easy tool-less
installation and ensure proper
airflow to equipment. Made of black
composite material and can be used
with tapped or square EIA universal
spaced rack mounting angles.
Bulle tIn: DAccY
Catalog Number
D19BPT1RU Blanking Panel, 19 in. 1 19 in., universal rack spacing,
D19BPT2RU Blanking Panel, 19 in. 2 19 in., universal rack spacing,
Description
Rack
Units Fits
tapped or square holes
tapped or square holes
Pkg.
Qty.
10
10
LEVELERS
Spec-00 212 I
Four post-type levelers allow
adjustment for uneven floors.
Levelers can be attached to the
Catalog Number Description
PLM12 Post-type Levelers
bottom of a frame or to a 0-mm solid
base. Levelers are plated and the
leveler base is capped with plastic
to provide resistance to marring.
Adjustable for 17-mm to 35-mm
height. Ball and socket construction.
Four levelers will suppor t a
maximum of 453.6 kg (1000 lb.).
Bulle tIn: p 20
PH 763.422.26 61 • FAX 763.42 2.2588 • HOFFMA NONL INE.COMEQUIPMENT PROTECTION SOLUTIONS NETWORKING 2
Page 3
PROLINE™ FRAME FLOORMOUNTING BRACKET
Provides a structural method of bolting a PROLINE™ frame to the
GROUNDING BAR SYSTEM
INDUSTRY STANDARDS
floor. Fits all frame sizes. Made of 12 gauge steel with plated finish.
Kit includes four brackets and mounting hardware.
Not for use on colocation frames, which include welded-in floor
mounting brackets.
Bulle tIn: DpY
FREESTAND CABINETS PROL INE™ A ccEs sORI Es
Catalog Number Description
PFBK PROLINE Frame Floor-Mounting Bracket
UL Component Recognized; File No. E61997
Three sizes of grounding bars and insulated mounting brackets
are available. Bars are plated copper with M6 and M5 tapped
holes to provide a common point for grounding equipment. Fits all
enclosures if mounted vertically. See table for horizontal mounting.
Bulle tIn: p 20
Catalog Number
PGS2K Fits 400-mm deep frame
PGS4K Fits 600-mm deep frame
PGS6K Fits 800-mm deep frame
Description
front to back horizontally
front to back horizontally
front to back horizontally
Length
mm/in.
200
7.87
400
15.75
600
23.62
Number of
Holes and
Screws M6
3/5 10/10
9/11 20/20
15/17 30/31
Number of
Holes and
Screws M5
PROLINE™ GROUNDING KIT
The Grounding Kit allows a
PROLINE™ enclosure to be
grounded to VDE specifications.
Includes six 12 gauge wires 411 mm
(16.19 in.) long with ring terminations
and M6 mounting hardware.
Bulle tIn: p 9
Catalog Number
PGK 12 ga. 411
Wire
Size
Length Between
Ring Terminals
mm/in.
16.19
Ring Terminal
Hole Diameter
mm/in.
7
.29
EQUIPMENT PROTECTION SOLUTIONSSUBJECT TO CHANGE WITHOUT NOT ICENETWORKING3
Spec-00 212 I
Page 4
FREESTAND CABINETS PROL INE™ A ccEs sORI Es
CASTER KIT
A set of four casters (two locking,
two non-locking) that mount directly
to the bottom of a PROLINE ™
frame, 0-mm, or 100-mm Solid
Base or a Console. (Do not use on
plinth bases.) Casters elevate the
enclosure 110 mm (4.33 in.) when
installed. Caster frames are plated
steel with ball-bearing pivots.
Caster wheels are made of a black
polyamide material. Kit includes
M12 mounting hardware.
Order separately.
Casters Maximum Load: 1000 lb.
(453 kg)
Exercise care when using casters
to move the cabinet. Avoid tipping
and damage to the cabinet and
its contents by slowly moving
the cabinet on its casters across
smooth, flat flooring. Avoid:
• large cracks
• floor displacement
• seams
• gravel
• any other obstruction
Never use casters while
transporting a cabinet by truck on
roadways.
Contact Hoffman if further
information is needed.
Bulle tIn: p 20
Catalog Number Description
PC1M12 Set of 4 Casters
SCREW PACKAGES
CAGE NUT PACKAGE
Screw Packages are for mounting
rack panels and equipment to rack
angles.
Bulle tIn: A80, DAccY, X20
Cage Nut Packages are for use with
square-hole rack angles. Cage nuts
are plated steel.
Bulle tIn: DAccY, p20
Catalog Number
ES1224 Silver 12-24 x 5/8 in. combo head 20
ES1224250 Silver 12-24 x 5/8 in. combo head 250
ES1224B Black 12-24 x 5/8in. combo head 20
ES1224B250 Black 12-24 x 5/8 in. combo head 250
ASM5 Silver M5 x 20 mm Combo Head 20
ASM6 Silver M6 x 16 mm combo head 20
ASM5T Silver M5 x 12 mm thread-forming Phillips hex head screws 20
ASM6250 Silver M6 x 16 mm combo head 250
AS1032 Silver 10-32 x 5/8 in. combo head 20
AS1032250 Silver 10-32 x 5/8 in. combo head 250
AS1032B Black 10-32 x 5/8 in. combo head 20
Use ASM5T on PROLINE
Catalog Number
PM5CN Silver M5 cage nut 20
PM6CN Silver M6 cage nut 20
PM6CN250 Silver M6 cage nut 250
P1032CN Silver 10-32 cage nut 20
P1032CN250 Silver 10-32 cage nut 250
P1224CN Silver 12-24 cage nut 20
P1224CN250 Silver 12-24 cage nut 250
Color Description
™
frame or Net Series extruded holes.
Color Description
Pkg. Qty.
Pkg. Qty.
Spec-00 212 I
PH 763.422.26 61 • FAX 763.42 2.2588 • HOFFMA NONL INE.COMEQUIPMENT PROTECTION SOLUTIONS NETWORKING 4
Page 5
MOUNTING CHANNEL
Allows rack angles and other accessories to be positioned at any
depth within the cabinet. Rails mount front to back in PROLINE™
frame. 14 gauge steel with RAL 9005 black polyester powder
paint finish. Includes two rails, mounting hardware and four M6
spring nuts for mounting accessories. Use hardware kit APSM6CN
(package of 20 screws, washers and spring nuts) for mounting
additional rack angles or other accessories to the mounting
channels.
Bulle tIn: DpY
Catalog Number
PMU8B Mounting Channel 800
PMU9B Mounting Channel 900
PMU10B Mounting Channel 1000
PMU11B Mounting Channel 1100
PMU12B Mounting Channel 1200
APSM6CN Mounting Channel Hardware Kit —
Description
Fits Frame Depth
FREESTAND CABINETS PROL INE™ A ccEs sORI Es
EQUIPMENT PROTECTION SOLUTIONSSUBJECT TO CHANGE WITHOUT NOT ICENETWORKING5
Spec-00 212 I
Page 6
FREESTAND CABINETS PROL INE™ A ccEs sORI Es
GRID STRAPS
Grid Straps are 14 gauge plated steel. They are provided with
specially designed rectangular holes to allow the use of cage nuts
or front-loading cage nuts. Mounting holes are provided on 25-mm
centers. Grid Straps are available with either 1 row or 3 rows of
holes and are furnished in pairs. Mounting hardware to attach Grid
Straps to the frame or to other Grid Straps is included.
• Can be mounted front-to-back horizontally across the bottom or
sides of the PROLINE™ frame
• Can be mounted left-to-right horizontally between front-to-back
pairs or from the sides of the PROLINE frame
• Can be mounted vertically between horizontally mounted Grid
Straps
Bulle tIn: DpY, p20
Catalog Number
PGH1S5 One Row 342 13.46 500 —
PGH1S6 One Row 442 17.40 600 —
PGH1S7 One Row 542 21.34 700 600
PGH1S8 One Row 642 25.28 800 700
PGH1S9 One Row 742 29.21 900 800
PGH1S10 One Row 842 33.15 1000 900
PGH1S11 One Row 942 37.08 — 1000
PGH1S13 One Row 1142 44.96 — 1200
PGH1S17 One Row 1542 60.71 — 1600
PGH3S4 Three Row 242 9.53 400 —
PGH3S5 Three Row 342 13.46 500 —
PGH3S6 Three Row 442 17.40 600 —
PGH3S7 Three Row 542 21.34 700 600
PGH3S8 Three Row 642 25.28 800 700
PGH3S9 Three Row 742 29.21 900 800
PGH3S10 Three Row 842 33.15 1000 300
PGH3S11 Three Row 942 37.08 1100 1000
PGH3S12 Three Row 1242 48.89 1200 —
PGH3S13 Three Row 1142 44.96 — 1200
PGH3S17 Three Row 1542 60.71 — 1600
Hole Pattern L (mm) L (in.)
Fits Frame
Depth
Fits Frame
Width
Spec-00 212 I
PH 763.422.26 61 • FAX 763.42 2.2588 • HOFFMA NONL INE.COMEQUIPMENT PROTECTION SOLUTIONS NETWORKING 6
Page 7
FULLHEIGHT VERTICAL GRID STRAPS
19IN. AND 23IN. RACK ANGLES
Rack angles can be moved forward if desired. Deeper positions
Provide expanded vertical mounting
positions. Made of plated steel.
25-mm spacing between mounting
positions. Use cage nuts or frontloading cage nuts. Sold in pairs.
Mounting hardware included.
Bulle tIn: p 20
PROLINE™ FASTENER PACKAGES
Use to fasten components to the
grid system. PGF Packages include
20 front-loading clip nuts (M6) and
20 combination-drive washer-head
bolts (M6).
Grounding Package is used with the
rectangular holes in the PROLINE™
frame to provide electrical
continuity between the frame and
the grid system. ASM5T Package is
used with PROLINE frames having
round holes. Package includes 20
M5 self-tapping screws.
Bulle tIn: DAccY, p20
FREESTAND CABINETS PROL INE™ A ccEs sORI Es
Catalog Number
PGH3S14V 1295 50.98 1400
PGH3S16V 1495 58.86 1600
PGH3S18V 1695 66.73 1800
PGH3S20V 1895 74.61 2000
PGH3S22V 2095 82.48 2200
Catalog Number
ASM5T M5 x 12 mm thread-forming Phillips hex head screws Round holes 20
PGFM6 Standard Package - M6 cage nuts and bolts Rectangular holes 20
PGFGM6 Grounding Package - M6 grounding cage nuts and bolts Tapped holes 20
Description Use in
L (mm) L (in.)
Fits Frame
Height
Pkg. Qty.
Made of 14 gauge steel with square holes or 12 gauge steel with 1032 tapped holes. Provides 19-in. rack spacing when mounted in 600mm wide frames, and 23-in. rack spacing when mounted in 700-mm
wide frames. Use with frame reducing brackets to provide 19-in. or
23-in. spacing in 700-mm or 800-mm wide frames. Sizes available
for multi-compartment colocation applications. Finish is black RAL
9005 polyester powder paint with flat finish. Furnished in pairs. The
standard rack angle position is 44 mm behind the door opening.
Catalog Number
PRA1912THL1 Square 19 PROLINE™ DataCom Packages 1200 24 1091 42.97
PRA1916TPL1 Tapped 19 PROLINE™ DataCom Packages 1600 33 1491 58.72
PRA1918THL1 Square 19 PROLINE™ DataCom Packages 1800 38 1691 66.59
PRA1918TPL1 Tapped 19 PROLINE™ DataCom Packages 1800 38 1691 66.59
PRA1920THL1 Square 19 PROLINE™ DataCom Packages 2000 42 1892 74.47
PRA1920TPL1 Tapped 19 PROLINE™ DataCom Packages 2000 42 1892 74.47
PRA192320THL1 Square 19 & 23 PROLINE™ DataCom Packages 2000 42 1892 74.47
PRA1921TPL1 Tapped 19 PROLINE™ DataCom Packages 2100 45 2041 80.37
PRA1921THL1 Square 19 PROLINE™ DataCom Packages 2100 45 2041 80.37
PRA1922THL1 Square 19 PROLINE™ DataCom Packages 2200 47 2091 82.34
PRA1922TPL1 Tapped 19 PROLINE™ DataCom Packages 2200 47 2091 82.34
PRA192322THL1 Square 19 & 23 PROLINE™ DataCom Packages 2200 47 2091 82.34
PRA1924TPL1 Tapped 19 PROLINE™ DataCom Packages 2400 51 2291 90.21
Hole Type Description (in.) Use With
require the use of grid straps or mounting channels. For joining
cabinets with rack angles in the full forward position, use Joining
Kit PJ2FF. Shelves, drawer, guides and pull-out shelves require t wo
sets of rack angles or frame accessory brackets installed in the
frame.
For 700- and 800-mm wide cabinets, reducer or cable manager must be
ordered.
Bulle tIn: Dpc
Fits Frame/Cabinet
Height (mm)
Rack
Units
Length
(mm)
Length
(in.)
EQUIPMENT PROTECTION SOLUTIONSSUBJECT TO CHANGE WITHOUT NOT ICENETWORKING7
Spec-00 212 I
Page 8
FREESTAND CABINETS PROL INE™ A ccEs sORI Es
ADJUSTABLE RACKMOUNTING RAILS
FRAMEREDUCING BRACKETS FOR FRAMES OR GRID
Mounting rails allow rack angles to be positioned anywhere within
the PROLINE™ frame. The left-to-right adjustment pertains only
when the enclosure is wider than the minimum width required for
rack angles. Includes two right-hand and two left-hand 12 gauge
plated or painted steel mounting rails. Mounting hardware is
included.
Bulle tIn: DpY, p20
Catalog Number
PBARA6 511 20.11 600 Plated
PBARA8 711 27.98 800 Plated
PBARA9 811 31.92 900 Plated
PBARA9B 811 31.92 900 Painted RAL 9005 Black
PBARA10B 911 35.86 1000 Painted RAL 9005 Black
PBARA11B 1011 39.79 1100 Painted RAL 9005 Black
PBARA12B 1111 43.73 1200 Painted RAL 9005 Black
L (mm) L (in.) Fits Frame Depth
Finish
STRAPS
Frame-Reducing Brackets mount directly to 700- or 800-mm wide
PROLINE™ frames or to grid straps. Converts wider frames to
600-mm wide, allowing 19-in. rack angles to fit, or to 700-mm wide,
allowing 23-in. rack angles to fit. Can be used to left- or right-justify
the rack-mounted equipment. Furnished in sets of four. 14 gauge
plated steel. Mounting hardware is included.
Bulle tIn: p 20
Reduces
Frame
Catalog Number
PRB50 50 50 1.97 From 700 to 600
PRB100 100 100 3.94 From 800 to 600
PRB200 200 200 7.87 From 1000 to 600
Width W (mm) W (in.)
Converts Frame Width
From 800 to 700 mm
From 800 to 700
From 700 to 600 mm
From 1000 to 800
From 800 to 600 mm
Spec-00 212 I
PH 763.422.26 61 • FAX 763.42 2.2588 • HOFFMA NONL INE.COMEQUIPMENT PROTECTION SOLUTIONS NETWORKING 8
Page 9
FREESTAND CABINETS PROL INE™ A ccEs sORI Es
FRAMEREDUCING BRACKETS FOR FRAMES OR
180DEGREE HINGE KIT
Optional hinging for steel solid, window or disconnect doors. The
MOUNTING CHANNEL
Frame-reducing brackets mount directly to 700-mm or 800-mm
wide PROLINE™ frames or to mounting channel. Convert wider
frames to 600-mm wide, allowing 19-in. rack angles to fit, or to 700mm wide, allowing 23-in. rack angles to fit. Can be used to left- or
right-justif y the rack-mounted equipment. Made of 14 gauge steel
painted with flat-black RAL 9005 polyester powder. Furnished in
sets of four. Mounting hardware is included.
Bulle tIn: DpY
Catalog
Number
PMURB50 50 50 1.97 From 700 to 600, From 800 to 700
PMURB100 100 100 3.94 From 800 to 600, From 800 to 700, From 700
Reduces Frame
Width
Frame Reducing Bracket Selection Guide
PROLINE Frame Width
600 mm (23.60) No reducing
700 mm (27.60) with grid straps PRB50 PRB 100 No reducing brackets
W
(mm)W (in.)
Setting 19 in.
Centered
brackets
Converts Frame Width
to 600
Setting 19 in. Left
or Right
No reducing
brackets
Setting 23 in.
Centered
—
Setting 19 in.
PROLINE Frame Width
700 mm (27.60) with mounting channel PMURB50 PMURB100 No reducing brackets
800 mm (31.50) with grid straps PRB100 PRB200 PRB50
800 mm (31.50) with mounting channel PMURB100 — PMURB50
Centered
Setting 19 in. Left
or Right
Setting 23 in.
Centered
180-degree hinges provide a door opening up to 260-degrees on
single-bay enclosures. These hinges mount to the door flange
and have a low-profile appearance. The kit includes three hinges
with textured black polyester powder paint and all necessary
mounting hardware. Cannot be used on PROLINE™ FLOTEK™ or
CONNECTEK™ front doors.
Bulle tIn: p 20
Catalog Number Description
PH180 180-Degree Hinge Kit
EQUIPMENT PROTECTION SOLUTIONSSUBJECT TO CHANGE WITHOUT NOT ICENETWORKING9
Spec-00 212 I
Page 10
FREESTAND CABINETS PROL INE™ A ccEs sORI Es
DOORMOUNT FAN TRAY AND BLOCKING PLATE
The Door-Mount Fan Tray is used with perforated PROLINE ™
doors to blow air through the perforations. Mounts to door bars.
Use Blocking Plates to prevent shor t cycling of fans. Includes two
6-in. fans and mounting plate, two finger guards, power cord and
mounting hardware.
The Blocking Plate is used with the Door-Mount Fan Tray to direct
airflow and prevent shor t cycling. Multiple plates can be used to
fill door opening and achieve desired airflow. Mounts to door bars.
Includes one blocking plate and mounting hardware.
Bulle tIn: DpY, DtHRM
Catalog Number
PF06021DR6 Door-Mount Fan Tray 600 115 VAC
PBLNKDR6 Blocking Plate 600 —
Description
Fits Door Width
mm/in.
Voltage
FLUSH KEYLOCKING TRIGGER LATCH WITH RANDOM KEY CODES
Flush design. Over 100 random key
codes with available master. Black
textured polyester powder paint
finish. Includes two trigger latches
with matching key code and t wo
keys. Designed to replace locking
trigger latch. For use on PROLINE™
Voice/Data and Colocation doors
only.
Bulle tIn: Dpc
SIDE COVER LOCK
Fits in pre-punched hole to
secure DataCom solid side from
unauthorized entry.
Bulle tIn: Dpc
Catalog Number Description
PTKLDC Flush keylocking Trigger Latch with random key codes
Catalog Number
PSCLO Side Cover Lock 2233
Description
Key Code
Spec-00 212 I
PH 763.422.26 61 • FAX 763.42 2.2588 • HOFFMA NONL INE.COMEQUIPMENT PROTECTION SOLUTIONS NETWORKING 10
Page 11
FLUSH SWING HANDLES
Flush Handles are optional for any solid, window or disconnect door
Handle with Screwdriver Defeater
that includes 3-point latching, except Voice/Data and Colocation
cabinets. They are ergonomically designed to provide style and
function in a low profile. The handle is die-cast zinc finished with
RAL 9005 textured black polyester powder paint. Provision to
add your logo is included. Handle can be installed to rotate either
clockwise or counterclockwise.
DIN LOCK INSERTS (FOR DIN PROFILE HANDLE ONLY)
The DIN profile keylock provides
keylocking security for the Flush
Swing Handle with DIN provision.
Includes profile lock and two keys.
Order one profile lock for each
handle.
DIN Lock Kit for PROLINE™
DataCom doors includes two locks
keyed alike with one of 100 different
key codes and two keys (master key
available).
All DIN Lock Inserts are zinc die-cast.
Bulle tIn: DpY, p20
FREESTAND CABINETS PROL INE™ A ccEs sORI Es
Enclosure security is provided by the integrated tool-to-open
feature that releases the handle when rotated, allowing access to
the enclosure.
Handle with Keylock
Keylock feature locks the handle to provide security for the
enclosure. When the key is in the unlocked position, the pushbutton
releases the handle to provide access to the enclosure. Two keys
are furnished.
Handle for Padlock
Padlocking Handle provides security when using up to a 5/16
padlock. Pushbutton releases the handle to provide access to the
enclosure.
Handle with DIN Profile Provision
DIN Flush Handle is provided with the option to add your DIN profile
lock or to accept Hoffman DIN profile lock PDKL (order separately).
Bulle tIn: p 20
Catalog Number Description
PFHDF Flush Handle with Defeater
PFHKBL Keylocking Flush Handle
PFHPBL Padlocking Flush Handle
PFHDBL DIN Profile Flush Handle
Catalog Number Description
PKOSLFH Slotted insert profile cylinder
PKOTM7FH 7-mm triangle insert profile cylinder
PKOSM7FH 7-mm square insert profile cylinder
PKOTM8FH 8-mm triangle insert profile cylinder
PKODBK3FH Double-bit 3-mm insert profile cylinder
PDKL DIN keylock, 2 keys included, key code 333
PDKLRKPR DIN Lock Kit for PROLINE DataCom doors
DIN profile inserts are used with DIN flush swing handles. One key is included (except for slotted insert).
L HANDLE
The L Handle is a st ylish option for
any solid, window or disconnect
door, except Voice/Data or
Colocation cabinets. It can be
installed to rotate either clockwise
or counterclockwise. Handle comes
with a bezel, includes keylocking
provision and is finished with RAL
9005 textured black polyester
powder paint. Two keys are included.
The bezel permits your logo to be
inser ted.
Bulle tIn: p 20
Catalog Number Description
PLHK L Handle with 2 keys and logo slot, key code 333
EQUIPMENT PROTECTION SOLUTIONSSUBJECT TO CHANGE WITHOUT NOT ICENETWORKING11
Spec-00 212 I
Page 12
FREESTAND CABINETS PROL INE™ A ccEs sORI Es
PAGODA EXHAUST VENTS
Pagoda Exhaust Vents can be field-installed on any PROLINE™
solid top. An axial fan and finger guard are mounted in a housing.
A drip-proof raised cover is removable from inside the enclosure.
Gasket and mounting hardware are included. Vent housing and
raised cover are 14 gauge steel finished with RAL 7035 textured
light-gray polyester powder paint.
Bulle tIn: p 20
HIGHPERFORMANCE PAGODA EXHAUST VENT
Vents fit on standard PROLINE™ top with vent cutout or can be
field-installed on any PROLINE solid top. The Pagoda Vent features
an integral centrifugal blower mounted in a housing that includes
a drip-proof removable hood, wire mesh finger guard, perimeter
gasket and terminal block. Electromagnetic-compatible (EMC)
Pagoda Vents include a conductive screen, conductive gasket, line
filter and 6-ft. power cord with stripped leads. Pagoda Vent housing
and hood are rugged 16 gauge steel finished with RAL 7035 textured
light-gray polyester powder paint. EMC vents are finished with paint
over plated surfaces. Installation hardware is included.
Bulle tIn: p 20, p20eM
Catalog Number
PPT1 Leadwires 115
PPT1C Power cord 115
PPT2 Leadwires 230
Description
Volts
Catalog Number
PPTHP1 Leadwires 115 1.7 Top with high-performance pagoda vent cutout
PPTHP1C Power cord 115 1.7 Top with high-performance pagoda vent cutout
PPTHP1EMC Power cord 115 1.7 Top with high-performance pagoda vent cutout on EMC enclosures
PPTHP2 Leadwires 230 .9 Top with high-performance pagoda vent cutout
PPTHP2EMC Power cord 230 .9 Top with high-performance pagoda vent cutout
Spec-00 212 I
Description Voltage Full Load Amps
PH 763.422.26 61 • FAX 763.42 2.2588 • HOFFMA NONL INE.COMEQUIPMENT PROTECTION SOLUTIONS NETWORKING 12
Use With
Page 13
FREESTAND CABINETS PROL INE™ A ccEs sORI Es
MOBILE BASE
Mobile Bases fit 600- and 800-mm wide frames. They extend
beyond the front and rear of 600-mm cabinets to provide enhanced
stability. Provides front extension only on 800-mm cabinets.
Constructed of steel finished in RAL 9005 textured black polyester
powder paint. The base fastens to the underside of the frame and
provides integral mounting of furnished casters. The front and rear
top surfaces of the base are trimmed with black rubber mats 3-mm
thick.
Casters and mounting hardware are furnished.
Four non-locking casters provide a maximum load-bearing
capacity of 1000 lb. (453.6 kg).
Exercise care when using casters to move the cabinet. Avoid tipping
and damage to the cabinet and its contents by slowly moving the
cabinet on its casters across smooth, flat flooring. Avoid:
• large cracks
• floor displacement
• seams
• gravel
• any other obstruction
Never use casters while transporting a cabinet by truck on
roadways.
Contact Hoffman if further information is needed.
Bulle tIn: p 20
Catalog Number
PMB66 40.91 x 23.62 1039 x 600 600 x 500 and 600 x 600
PMB69 52.72 x 23.62 1339 x 600 600 x 800 and 600 x 900
PMB86 40.91 x 31.50 1039 x 800 800 x 500 and 800 x 600
PMB89 52.72 x 31.50 1339 x 800 800 x 800 and 800 x 900
AxB in. AxB mm
Fits Frame B x C (mm)
MOBILE BASE LEVELING KIT
Levelers mount in the outer corners
of the Mobile Base, providing loadbearing capacity of 1000 lb. (453.6
kg).
Bulle tIn: p 20
Catalog Number
PMBLM12 Mobile Base Leveling Kit Mobile Base
Description
Use with
EQUIPMENT PROTECTION SOLUTIONSSUBJECT TO CHANGE WITHOUT NOT ICENETWORKING13
Spec-00 212 I
Page 14
PH FAX HOFFMANONLINE.COMEQUIPMENT PROTECTION SOLUTIONS 14
Loading...