Hoei Precision DSR-4000dp User Manual

HOEI PRECISION

DESKTOP CD/DVD DUPLICATOR

DSR-4000dp

DSR-4000dp-5-MX / DSR-4000dp-10-MX

USER’s MANUAL

Rev 2.0

Thank you for your purchase of the DVD duplication system “DSR-4000dp”. Read this user’s manual thoroughly to understand the use and operation of the “DSR-4000dp”. These specifications are subject to change without prior notice due to functional improvements.

DSR-4000dp User’s Manual

Reproduction or use, without permission from HOEI SANGYO Co.,Ltd.,

of any portion of this manual is prohibited and are in violation of applicable laws.

TABLE OF CONTENTS

Names and Functions................................................................................................................................5

Operation Panel...................................................................................................................................... 7

Notes for handling................................................................................................................................... 10

Power supply........................................................................................................................................ 10

Installation Notes..................................................................................................................................11

Installation space.................................................................................................................................. 12

Unpacking............................................................................................................................................ 13

Maintenance......................................................................................................................................... 13

Transportation...................................................................................................................................... 13

How to operate the DSR......................................................................................................................... 14

Operation Panel.................................................................................................................................... 14

Turning on/off the power..................................................................................................................... 15

Main menu........................................................................................................................................... 16

Display chart of Main menu: ............................................................................................................... 16

CD DUPLICATOR................................................................................................................................. 17

Format.................................................................................................................................................. 17

Mode and master drive for CD ............................................................................................................ 17

Basic Operations for CD...................................................................................................................... 18

Copy from disc to disc (CDtoCD)....................................................................................................... 18

Register the master disc (CDtoHD)..................................................................................................... 19

Copy from HDD to DVD (HDtoCD)................................................................................................... 21

Select the mater drive........................................................................................................................... 22

Simulation copy (SIMULATION)....................................................................................................... 23

Setup of CD (SETUP).......................................................................................................................... 24

Change and set each mode................................................................................................................ 24

Select the write speed (WRITE SPEED).......................................................................................... 25

Display the drive inquiry string (DRIVE INQUIR Y )....................................................................... 26

Display the firmware version (F/W VERSION)............................................................................... 27

Disc Erase ......................................................................................................................................... 28

Error during the process....................................................................................................................... 29

DVD DUPLICATOR.............................................................................................................................. 30

Format.................................................................................................................................................. 30

Media ................................................................................................................................................... 30

Mode and master drive for DVD......................................................................................................... 30

Basic Operations for DVD................................................................................................................... 31

Copy from disc to disc (DVDtoDVD)................................................................................................. 31

Register the master disc (DVDtoHD).................................................................................................. 32

Copy from HDD to DVD (HDtoDVD) ............................................................................................... 34

Select the mater drive........................................................................................................................... 35

Simulation copy (SIMULATION)....................................................................................................... 36

Setup of DVD (SETUP)....................................................................................................................... 37

Change and set each mode................................................................................................................ 37

How to change the mode................................................................................................................... 37

Select the write speed (WRITE SPEED).......................................................................................... 38

Display the drive inquiry string (DRIVE INQUIR Y )....................................................................... 39

Display the firmware version (F/W VERSION)............................................................................... 40

Disc Erase ......................................................................................................................................... 41

Error during the process.................................................................................................................... 42

PRV-LX1................................................................................................................................................. 43

How to connect with PRV-LX1 ........................................................................................................... 43

How to start.......................................................................................................................................... 44

How to shut down................................................................................................................................ 44

How to use ........................................................................................................................................... 45

Register to HDD from PRV-LX1 (ToHD) ........................................................................................ 46

Trouble shooting............................................................................................................................... 47

UTILITY................................................................................................................................................. 48

How to start UTILITY......................................................................................................................... 48

HDD FORMAT.................................................................................................................................... 49

NETWORK............................................................................................................................................. 50

How to connect the units...................................................................................................................... 50

Setup the NET ID switch.................................................................................................................. 50

Connect the cable.............................................................................................................................. 50

Power on and NETWORK READY................................................................................................. 51

Operations of NETWORK................................................................................................................... 52

Distribute the master data from the master disc to the slave unit (CD/DVDtoNET)....................... 52

Distribute the master data from the master HD to the slave unit (HDtoNET) ................................. 53

Copy/Verify after the master distribution ............................................................................................ 54

Display of SLAVE BUSY for the master distribution......................................................................... 54

Troubleshooting................................................................................................................................... 55

Firmware................................................................................................................................................. 55

How to upgrade / reload the firmware CD........................................................................................... 55

Error message.......................................................................................................................................... 56

System.................................................................................................................................................. 56

Read drive............................................................................................................................................ 56

Write drive ........................................................................................................................................... 56

HDD..................................................................................................................................................... 56

Others................................................................................................................................................... 57

Error Code List ....................................................................................................................................... 58

Read drive............................................................................................................................................ 58

Write Drive .......................................................................................................................................... 59

Names and Functions

Names and functions are as follows:

Front panel (DSR-400dp-5-MX: Master Unit)

Operation panel

Operation panel : There are LCD (liquid crystal display) to show the status of the DSR and switches to set

functions (Refer to “Operation Panel”).

A drive : DVD-RW writer has been installed.

LED : The status of the drive A is shown (See below).

B drive : DVD-RW writer has been installed.

LED : The status of the drive B is shown (See below).

C drive : DVD-RW writer has been installed.

LED : The status of the drive C is shown (See below).

D drive : DVD-RW writer has been installed.

LED : The status of the drive D is shown (See below).

Master DVD-ROM reader : Master read drive.

LED : The status of the Master Read Drive is shown (See below).

*LED indicators

OFF……………..A medium is not inserted. Or a medium is being acknowledged. ON………………A medium is inserted and the drive is ready to work. Flashing slowly…A process is being executed. Flashing quickly. An error has occurred.

A drive / LED

B drive / LED

C drive / LED

D drive / LED

Master DVD-ROM drive / LED

Power switch

Front panel (DSR-4000dp-10-MX: Master Unit)

Operation panel

Operation panel : There are LCD (liquid crystal display) to show the status of the DSR and switches to set functions

(Refer to “Operation Panel”).

A drive : DVD-RW writer has been installed.

LED : The status of the drive A is shown (see below).

B drive : DVD-RW writer has been installed.

LED : The status of the drive B is shown (see below).

C drive : DVD-RW writer has been installed.

LED : The status of the drive C is shown (see below).

D drive : DVD-RW writer has been installed.

LED : The status of the drive D is shown (see below).

E drive : DVD-RW writer has been installed.

LED : The status of the drive E is shown (see below).

F drive : DVD-RW writer has been installed.

LED : The status of the drive F is shown (see below).

G drive : DVD-RW writer has been installed.

LED : The status of the drive G is shown (see below).

H drive : DVD-RW writer has been installed.

LED : The status of the drive H is shown (see below).

Master DVD-ROM reader : Master read drive.

LED : The status of the Master Read Drive is shown (See below).

*LED indicators

A drive / LED

B drive / LED

C drive / LED

D drive / LED

E drive / LED

F drive / LED

G drive / LED

H drive / LED

Master DVD-ROM drive / LED

Power switch

Operation Panel

LCD (Liquid Crystal Display) : It shows status messages of the DSR.

LCD (Liquid Crystal Display)

No Yes

Yes Switch

No Switch

Yes Switch : To execute each selected mode/menu.

No Switch : To select each mode/menu.

Fan

USB connector

ET ID switch

Rear Panel (DSR-4000dp-5-MX: Master Unit)

AC outlet

115/230V switch

AC inlet

USB

NET ID

NET IN

NET OUT

ET IN connector

ET OUT connector

AC outlet : It turns on/off the power, interlocking with the power switch. AC inlet : It is an AC power supply socket.

115/230V switch : It is a switch for changing the input voltages (AC115/230).

USB : Connector to connect with the PC use via USB2.0. NET IN : Connector to connect master units together as a network feature.

Connect a cable from the NET OUT connector.

NET OUT : Connector to connect master units together as a network feature.

Connect a cable to a next master unit.

NET ID : Switch used for a network feature to select ID.

Be sure to use a tool such as the screwdriver to change the 115/230V Switch. Do not use your finger or any part of your body.

AC outlet

115/230V switch

AC inlet

Rear Panel (DSR-4000dp-10-MX: Master Unit)

Fan

USB

NET ID

NET IN

NET OUT

USB connector

ET ID switch

ET IN connector

ET OUT connector

AC outlet : It turns on/off the power, interlocking with the power switch. AC inlet : It is an AC power supply socket.

115/230V switch : It is a switch for changing the input voltages (AC115/230).

USB : Connector to connect with the PC use via USB2.0. NET IN : Connector to connect master units together as a network feature.

Connect a cable from the NET OUT connector.

NET OUT : Connector to connect master units together as a network feature.

Connect a cable to a next master unit.

NET ID : Switch used for a network feature to select ID.

Be sure to use a tool such as the screwdriver to change the 115/230V Switch. Do not use your finger or any part of your body.

Notes for handling

Handle the DSR in accordance with the following notes:

Power supply

・Use power supply for an ordinary house. ・Do not use an outlet near a big motor driven appliance (air conditioner, copying machine,

etc.).

・Use an outlet with stable power supply voltages.

・Do not overload an outlet. Do not use a service outlet for PCs.

・Wire the power cord properly.

・Do not touch the power cord with a wet hand.

・Be careful not to damage the power cord.

Inspect the power cord periodically. In the event that the power cord is damaged, contact the agent.

Be sure to use a tool such as the screwdriver to change the 115/230V Switch. Do not use your finger or any part of your body.

Earth

・Be sure to each the DSR to prevent an accident due to electricity leakage.

For grounding, use a 3P outlet or an earth cord from the 3P-2P conversion connector.

・

Moving

The DSR-4000dp-5 weights about 16kg. The DSR-4000dp-10 weights about 25kg.

Caution

Move it very carefully.

Notes for Handling

Installation Notes

Install the DSR in the following conditions:

・

in a level and stable place

・

in an airy place Temperature and humidity

・

Humidity: 20-80%RH (no dew formation)

・

・・・・・・・

Temperature: 5-40 ℃

Do not install it in the following places:

Under direct sunlight (If the machine is exposed to sunlight, shut out the light by using a blind or curtain.) a dusty place a place where there is a lot of vibration near fire a place where the temperature and humidity change drastically near a heating device such as a heater a place where air from an air conditioner blows near a container filled with water such as a vase

In winder at low humidity or in a place where static electricity is generated, use an

anti-static-electricity mat or humidifier to prevent the static electricity

Installation space

The dimensions of the DSR-4000dp-5-MX are as follows:

The dimensions of the DSR-4000dp-10-MX are as follows:

１００１００

Do not place anything within at least 5cm around the DSR. Clear anything at least 20cm behind he DSR. Securely place the rubber legs of the DSR on the desk or table.

Notes for using ・Do not hit it against anything

・・・

Do not insert a foreign material (e.g., metal chip) in it. Do not disassemble the housing or turn off the power while a process is being executed. If a malfunction occurs during the process, refer to “Section 6 Error”. Clean the DSR in accordance with “Section 1 Maintenance”.

・

８０８０

２００

１００１００

６８

８０８０

６８

４６５

３３２

４６５

３３２

６５

５０２

Notes for Handling

３３８

３４５

５０９

Unpacking

What comes with the DSR

Make sure that the following items are included in the package and there is no damage on the

DSR and accessories.

1 DSR-4000dp 1 2 Power cable 1 3 Instruction manual 1

If anything is missing, please contact the agent where you purchased the DSR

Part Name Part No. Qty

Maintenance

Cleaning

Before cleaning the DSR, switch it off and take the plug out of the socket.

Remove dust on the housing carefully by using a soft brush.

１．

If it is very dirty, wipe it with a soft cloth after soaking the cloth in water including a small

２．

amount of neutral detergent and squeezing it.

・

Do not use volatile chemicals such as benzene, thinner and alcohol. If they are used the surface of the housing might change in quality or shape.

・

Keep the inside of the DSR dry.

・

Do not use a bristle brush and a stiff cloth.

Transportation

If the DSR is transported after unpacking, pack it properly to protect it from shocks during

transportation

Prepare the packing materials and box that have been used for transporting the DSR.

Switch the DSR off.

Remove the interface cable and power cord.

If protection materials have been used for the drives before unpacking, place them

on the drives. Place the packing materials on the DSR. Put the DSR in the box.

How to operate the DSR

Operation Panel

The DSR works by using the switches on the operation panel. The LCD and LED indicate the status of the DSR.

Refer to “Names and Functions of Devices” (Introduction) for details.

LCD (Liquid crystal display)

It shows the status of the DSR in the normal mode. In the “panel setting” mode, the settings are shown on the screen. Up to 32 characters (16 characters x 2 lines) are shown on the LCD.

Switches

Yes Switch It is used to execute a menu/mode displayed on the LCD.

No Switch It is used to select a menu/mode.

No Yes

Turning on/off the power

Check the connections again before turning on the DSR

Caution

Turning on the power

1. Press the power switch on the lower right corner on the DSR

2. DSR begins initializing.

3. DVD copy function displays after initializing.

Turning off the power

DSR-4000 Ver X.XX

CD DUPLICATOR

HOEI PRECISION

If the power is not properly turned on, refer to “Error message” to take proper procedures.

1. Make sure that the process has been completed in the DSR

2. Turn off the power.

If you want to turn on the power again after turning it off, at least 5 seconds are required before turning in on again. Do not turn the power off while the hard drive is processed. Do not turn off the power while a panel setting is being stored. The panel setting might be lost.

Main menu

Select a main menu of DSR you want to use after powering on. DSR boots up the main menu you used last time except UTILITY. Main menus of DSR are as follows:

CD DUPLICATOR: You can use the DSR as a standalone CD duplicator. Please refer to

“Section 3. CD DUPLICATOR”.

DVD DUPLICA T OR: Y ou can use the DSR as a standalone DVD duplicator. Please refer to

“Section 4. DVD DUPLICATOR”.

DPM for General: You can use the DSR with the DPM88 application. Please refer to the

DPM88 user manual.

UTILITY: Utility menu of DSR. You can select HDD FORMAT.

Display chart of Main menu:

Section 3. CD DUPLICATOR

Section 4. DVD DUPLICATO

Refer to the DPM88 manual

Section 5. UTILITY

CD DUPLICATOR

Notice for CD

The followings are notices for operations of CD with the DSR.

Format

Supported CD formats by DSR are as follows:

COPY VERIFY READ CHECK (RD CHECK) CD-ROM mode 1 CD-ROM mode 2

CD-DA CD-ROM XA form 1 CD-ROM XA form 2

MIXED

Multi Session

○ ○ ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ × ○ ○ △ (*1) ○

*1 Cannot verify the multi session unless CD-ROM mode 1 or CD-ROM XA form 1.

CD-DA

Due to the specification of writer installed in the DSR-4000dp, the ISRC and catalogue code do not support even if they are

included in the master disc.

Mode and master drive for CD

There are three modes for CD.

* COPY--------------------------------------- Copy the data from master drive to blank disc.

* VERIFY------------------------------------ Verify (compare) the data between master drive and target disc (s).

* RD CHECK-------------------------------- Check if the copied data can be read properly.

* COPY + V (copy + verify)--------------- Copy and Verify in a row.

* COPY + R (copy + read check)--------- Copy and Read Check in a row.

There are two kinds of master drive.

* CD------------------------------- Disc inserted into the DVD-ROM drive is recognized as the master disc and read from this disc for

every process.

* HD ------------------------------ Internal HDD is the master drive. It is required to register the master data from disc in the

DVD-ROM drive first. After the registry in HDD, the master disc is no longer necessary.

Mode & master is saved as the last process you executed. LCD displays the mode & master in the CD main screen.

COPY START?

Mode Write speed Master drive

In this chapter, it is assumed to set COPY mode and explained the following items.

* Copy from disc to disc (CDtoCD)

* Register the master disc (CDtoHD)

* Copy from HDD to disc (HDtoCD)

(MEDIUM)

COPY START?

(CD to CD)

Basic Operations for CD Copy from disc to disc (CDtoCD)

1. For copying from CD to CD, press the YES switch after confirming the CD main screen as follows.

Notice: It is explained as Copy mode. If you want to change mode, refer to “Setup of CD, Select the mode (MODE SELECT)”.

2. Press the Yes switch to open the tray of master drive with the following message.

Insert the master disc and close the tray.

Notice: If the master disc is not inserted within 30 seconds, the screen goes back to 1. The tray does not open if the master disc is

3. Tray (s) of target drive opens with the following message. Insert the blank media and close the tray (s). If you do not want to insert

Notice: If any one of target disc (s) is inserted within 30 seconds, the screen goes back to 1.

4. DSR starts to analyze the master disc and the status LED beside the master & target drive (s) starts to blink if it is ready.

5. Copy is started after the master analysis.

6. Target disc (s) is automatically ejected if the copy completes, the status LED is lit off, and the screen goes back to 1.

☆ Refer to “Notices for CD” for the supported CD formats. ☆ If an error occurs, refer to “Error during process” at the end of this section.

COPY START?

(DVDtoDVD)

If the master is HDD (displayed “HDtoCD” in the second line), refer to “Copy from HD to disc (HDtoCD)”.

Default of write speed is the maximum write speed of target drive. If you want to change write speed, refer to “Setup of

CD, Select the write speed (WRITE SPEED)”.

INSERT

MASTER DISC

already inserted before pressing the YES switch. It would be the master disc.

the media to all target drives, close the tray (s) as empty.

INSERT

TARGET DISC

ANALYZING

MASTER

COPY 15:25

CD-DA

□□□□ 20%

COPY START?

(FAST)

1. Start from the CD main screen. No matter which mode/master is selected. Press the NO switch.

2. Press the YES button in the master selection screen as follows.

3. DSR asks if you want the DVD-ROM drive as the master drive. Press the YES button.

4. DSR asks if you want to copy from the master CD disc to blank CD-R (s). Press the YES button to copy from disc to disc and

5. HD area for CD in DSR is displayed. Select the HD area and press the YES button.

(1). No data yet registered in the area you select:

COPY START?

(CDtoCD)

MASTER SELECT?

>CD MASTER?

refer to “Copy from disc to disc (CDtoCD)”.

Press the NO switch to register the master data to HDD.

To CD DISC ?

(CD to CD)

Press the YES button to register the master data.

To CD A REA 1 ?

Press the YES button to start registration. Press the NO button to return.

REGISTRATION?

Tray of DVD-ROM drive opens with the following message. Insert the master disc and close the tray.

INSERT

MASTER DISC

DSR analyzes the master CD and starts registration. The master CD is ejected automatically once it completes.

ANALYZING

MASTER

(CD to HD)

COPY START?

(FAST)

To CD A REA 1 ?

(FREE )

REGIST 15:25

CD-DA

□□□□ 20%

+ 43 hidden pages

Hoei Precision DSR-4000dp User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual