HOBO® RX Wireless Sensor Network
O
C
HOBO RXW Repeater (RXW-RPTR-xxx) Manual
The HOBO RXW Repeater is designed to work with the HOBOnet Wireless Sensor Network in
which data is transmitted wirelessly from sensor motes across the network to the RX3000 station
and then uploaded to HOBOlink® web-based software. The repeater is ideal when there is an
obstruction between motes and the station or for extending the transmission range of motes in
the network. With HOBOlink, you can monitor the network, view graphs, set up alarms, download
data, and more.
Specifications
HOBO RXW Repeater
Models:
• RXW-RPTR-900 (US)
• RXW-RPTR-868 (Europe)
• RXW-RPTR-922
(Australia/NZ)
Included Items:
• Cable ties
• Screws
perating Temperature
Range
Radio Power 12.6 mW (+11 dBm) non-adjustable
Transmission Range Reliable connection to 457.2 m (1,500 ft) line of sight at 1.8 m (6 ft) high
Wireless Data Standard IEEE 802.15.4
Radio Operating
Frequencies
Modulation Employed OQPSK (Offset Quadrature Phase Shift Keying)
Data Rate Up to 250 kbps, non-adjustable
Duty Cycle <1%
Maximum Number of
Motes
Battery Type/
Power Source
Battery Life With NiMH batteries: Typical 3–5 years when operated in the temperature
Dimensions 16.2 x 8.59 x 4.14 cm (6.38 x 3.38 x 1.63 inches)
Weight 219 g (7.74 oz)
Materials PCPBT, silicone rubber seal
Environmental Rating IP67, NEMA 6
ompliance Marks RXW-RPTR-900: See last page
-25° to 60°C (-13° to 140°F) with rechargeable batteries
-40 to 70°C (-40 to 158°F) with lithium batteries
Reliable connection to 609.6 m (2,000 ft) line of sight at 3 m (10 ft) high
RXW-RPTR-900: 904–924 MHz
RXW-RPTR-868: 866.5 MHz
RXW-RPTR-922: 916–924 MHz
50 motes per one RX Wireless Sensor Network
Two AA 1.2V rechargeable NiMH batteries, powered by built-in solar panel
or two AA 1.5 V lithium batteries for operating conditions of -40 to 70°C (40 to 158°F)
range -20° to 40°C (-4°F to 104°F) and positioned toward the sun (see
Deployment and Mounting), operation outside this range will reduce the
battery service life
With lithium batteries: 1 year, typical use
RXW-RPTR-868: The CE Marking identifies this product as
complying with all relevant directives in the European Union
(EU).
RXW-RPTR-922: See last page
22249-A
Components and Operation
Mounting
Tab
Solar Panel
Repeater Closed, Front Repeater Closed, Back
Solar Panel Cable
Mounting Tab: Use the tabs at the top and bottom of the
repeater to mount it (see Deploying and Mounting).
Solar Panel: Position the solar panel towards the sun to charge
the repeater batteries (see Deploying and Mounting).
Eyelet: Use this eyelet to attach a 3/16 inch padlock to the
repeater for security.
Latch: Use the two latches to open and close the repeater door.
Ground Wire Port: Use this port to connect a ground wire (see
Deploying and Mounting).
Antenna: This is the built-in antenna for the radio
communications across the RX Wireless Sensor Network.
Solar Panel Cable: This cable connects the built-in solar panel
to the repeater circuitry.
LEDs: There are two LEDs to the left of the LCD screen. The
green LED blinks during the process of joining a network,
blinking quickly while the repeater searches for a network and
then slowly as the repeater registers with the network. Once
the network registration process is complete, the blue LED
blinks at 4 seconds to indicate normal operation. If the repeater
is not currently part of a network, the blue LED will be off. If the
blue LED is on and not blinking, there is a problem with the
repeater. Contact Onset Technical Support.
Battery Holder: The location where the batteries are installed
as shown (see Battery Information).
USB Port: Use this port to connect to the repeater to a
computer via USB cable if you need to update the firmware
(see Updating Repeater Firmware).
Button: Push this button for 1 second to illuminate the LCD or 3
seconds for the repeater to search for an RX Wireless Sensor
Latch
Eyelet
Ground Wire
Port
LEDs
Antenna
LCD Screen
Button
USB Port
Battery Holder
Repeater Opened
HOBO RXW Repeater (RXW-RPTR-xxx) Manual
Network to join (see Adding the Repeater to the RX Wireless
Sensor Network).
LCD Screen: The repeater is equipped with an LCD screen that
displays details about the current status. This example shows all
symbols illuminated on the LCD screen followed by definitions
of each symbol in the table.
LCD Symbol Description
The battery indicator shows the approximate battery
charge remaining.
This is a signal strength indicator. The more bars, the
stronger the signal between motes. If there is no x
icon next to the signal strength indicator, then the
repeater is part of an RX Wireless Sensor Network.
An empty signal strength icon plus the x icon
indicates that the repeater is not currently part of a
network. See Adding the Repeater to the RX Wireless
Sensor Network for details on how to add it to the
network.
When the repeater is in the process of joining a
network, the signal strength icon will blink and then
the bars in the icon will cycle from left to right. The x
icon will blink during the last step in the network
registration process (see Adding the Repeater to the
RX Wireless Sensor Network for details).
Adding the Repeater to the RX Wireless Sensor
Network
The repeater must join an RX Wireless Sensor Network before it
can begin transmitting data. This requires accessing the RX3000
station and the repeater at the same time so it is recommended
that you complete these steps before deploying the repeater.
Important: If you have not configured the RX3000 station with
the RXW Manager, follow the instructions in the RX3000 Quick
Start before continuing.
To add a repeater to the RX Wireless Sensor Network:
1. If the LCD is blank on the RX3000 station, press any button
to wake it up.
2. Press the Select button once (which shows the number of
smart sensors installed) and then press it again once if the
HOBO RXW Manager is installed in the left slot (module 1)
or twice if it is installed on the right slot (module 2).
Press this button to view the module
where the RXW Manager is installed
1-800-LOGGERS 2 www.onsetcomp.com
HOBO RXW Repeater (RXW-RPTR-xxx) Manual
3. Press the Search button (the magnifying glass). The
magnifying glass icon will blink while the RX3000 is in search
mode.
Press this button so the station is ready
to have the repeater join the network
4. Open the repeater door and install the batteries if you have
not already done so.
5. Press the button on the repeater for 3 seconds. The signal
strength icon will flash and then cycle.
Press this button for 3
seconds for the repeater
to join the network
6. Watch the LCD on the repeater.
a.
This signal strength icon
blinks while searching for
a network.
c.
b.
Once a network is found,
the icon will stop flashing
and the bars will cycle from
left to right.
d.
7. Press the Search button (the magnifying glass) on the
RX3000 station to stop searching for repeaters.
Press this button again to stop
searching for the repeater
When you are finished adding repeaters and wireless sensors to
the network, the total channel count on the RX3000 station LCD
for the RXW Manager module will represent the measurement
channels from all motes plus a battery channel for each mote
(including repeaters) in the RX Wireless Sensor Network.
Use HOBOlink to monitor repeater status. See the HOBOlink
Help for details on how to check status, add the repeater to a
map, and more.
Deployment and Mounting
When to Use a Repeater
• Motes cannot transmit data to each other if there is an
obstruction between them, such as a hill or mountain in
the example diagram below on the left. If there is an
obstruction in the path of two sensor motes or between a
sensor mote and the RXW Manager, then use a repeater
mounted on the obstruction between the two as shown in
the diagram below on the right.
This network connection
“x” icon blinks while the
repeater completes the
registration process,
which may take up to
five minutes.
Once the repeater has finished
joining the network, the “x” icon
is removed and the channel count
on the station LCD increases by
one for the repeater battery.
This process may take up to five minutes. The green LED
blinks quickly while the repeater searches for a network to
join and then blinks slowly while it completes the network
registration. Once the repeater has finished joining the
network, the green LED turns off and the blue LED then
blinks indefinitely while the repeater is part of the network.
Note: If the mote cannot find the network or has trouble
remaining connected during this process, make sure the
mote is in a vertical, upright position and within range of
the station.
1-800-LOGGERS 3 www.onsetcomp.com
• If the distance between two motes is greater than the
recommended transmission range in the specifications,
then you may need to add a repeater between them.
• If the signal between two motes is weak (consistently one
bar on the LCD) even though the motes are within the
recommended transmission range, add a repeater
between them.
Mounting and Positioning the Repeater
• Mount the repeater to a mast or pipe using cable ties or
affix the repeater to a wooden post or flat surface with
screws. Insert the cable ties or screws through the holes
on the mounting tabs.
• Consider using plastic poles such as PVC to mount the
repeater as certain types of metal could decrease the
signal strength.
HOBO RXW Repeater (RXW-RPTR-xxx) Manual
• Make sure the repeater remains in a vertical position once
it is placed in its deployment location for optimal network
communications.
• Make sure the repeater door is closed, with both latches
fully locked to ensure a watertight seal.
• Consider using a 3/16 inch padlock to restrict access to the
repeater. With the repeater door closed, hook a padlock
through the eyelet on the right side of the door and lock it.
• Position the repeater towards the sun, making sure the
solar panel is oriented so that it receives optimal sunlight
throughout each season. It may be necessary to
periodically adjust the repeater position as the path of the
sunlight changes throughout the year or if tree and leaf
growth alters the amount of sunlight reaching the solar
panel.
• Make sure the repeater is mounted a minimum of 1.8 m (6
feet) from the ground or vegetation to help maximize
distance and signal strength.
• There should not be more than five motes in any direction
at their maximum transmission range from the RXW
Manager. Data logged by a wireless sensor must travel or
“hop” across the wireless network from one mote to the
next until it ultimately reaches the RXW Manager at the
RX3000 station. To make sure the data can successfully
travel across the network, the mote should not be more
than five hops away from the manager.
• The RX Wireless Sensor Network can support a maximum
of 50 motes.
• Use a #4-40 screw to attach a ground wire to the port on
the back of the repeater if you are deploying it in a
location where lightning is a concern.
Maintenance
The repeater is designed for outdoor use, but should be
inspected periodically. When inspecting the repeater, do the
following:
• Verify the repeater is free of visible damage or cracks.
• Make sure the repeater is clean. Wipe off any dust or
grime with a damp cloth.
• Wipe off any water before opening the repeater.
• Make sure the interior seal is intact and the latches are
fully locked when the repeater door is closed.
Updating Repeater Firmware
If a new firmware version is available for the repeater, use
HOBOlink to download the file to your computer.
1. In HOBOlink, go to Devices > List and click your station
name.
2. On the station page, click Overview and scroll down to
Device Information.
3. Click the Wireless tab. This icon appears next to the
mote if there is a new version of firmware available.
4. Click the firmware upgrade link. Click Download and
save the firmware .bin file to your computer.
5. Connect the mote to the computer with a USB cable (open
the mote door and use the USB port to the right of the
LCD). The blue LED is illuminated while connected.
6. The mote appears as a new storage device in the
computer’s file storage manager. Copy the downloaded
firmware file to the new storage device (the mote). The
blue LED will blink slowly while the file is copying.
7. After the file is copied to the mote, the LED will stop
blinking and remain a steady blue. Eject the storage device
from the computer and disconnect the cable from the
mote. The firmware installation process will begin
automatically on the mote. The blue LED will blink rapidly
while the firmware is installed. Once the firmware
installation is complete, the LCD symbols return and the
mote will automatically rejoin the network.
Notes:
• Mac® users: A message may appear indicating the disk
has not ejected properly when disconnecting the mote
from the computer. The mote is operational and you can
ignore the message.
• If the blue LED turns off abruptly while copying the file or
installing the firmware, a problem has occurred. Contact
Onset Technical Support for help.
Battery Information
The repeater uses two 1.2 V rechargeable NiMH batteries,
charged by the built-in solar panel. The quality and quantity of
solar light can affect whether the battery is sufficiently charged
to last through the night and cloudy periods. Make sure the
repeater is placed in a location that will receive several hours of
sunlight each day. If the repeater does not receive enough
sunlight to recharge the batteries, the battery life is estimated
at 3–4 months. When batteries are regularly recharged,
expected battery life is estimated at 3–5 years. Battery life
varies based on the ambient temperature where the repeater is
deployed, the logging interval, the number of tripped alarms,
and other factors. Deployments in extremely cold or hot
temperatures can impact battery life. Estimates are not
guaranteed due to uncertainties in initial battery conditions and
operating environment.
Repeater operation will stop when battery voltage drops to
1.8 V. Repeater operation will return if the battery recharges to
2.3 V. If the batteries are unable to be recharged, replace them
with fresh rechargeable batteries. Note: if you install used
rechargeable batteries that together are less than 2.3 V, the
repeater will not resume operation.
To replace rechargeable batteries:
1. Open the repeater door.
2. Remove the old batteries and install fresh ones observing
polarity.
1-800-LOGGERS 4 www.onsetcomp.com
HOBO RXW Repeater (RXW-RPTR-xxx) Manual
3. Make sure the solar panel cable is plugged in.
Make sure
solar panel
cable is
installed
when using
rechargeable
batteries
The repeater contacts the network once the new batteries are
installed. The green LED blinks quickly while the repeater
searches for a network to join and then blinks slowly while it
completes the network registration. Once the repeater has
finished joining the network, the green LED turns off and the
blue LED then blinks indefinitely while the repeater is part of
the network.
Lithium Batteries
You can use two 1.5 V lithium batteries (HWSB-LI) for operation
at the extreme ends of the repeater operating range. Lithium
battery life is an estimated at 1 year, but varies based on the
ambient temperature where the repeater is deployed, the
logging interval, the number of tripped alarms, and other
factors. Estimates are not guaranteed due to uncertainties in
initial battery conditions and operating environment. When
using lithium batteries, you must disconnect the solar panel
cable because the batteries will not be recharged.
To install lithium batteries:
1. Open the repeater door.
2. Remove any old batteries and install the new ones
observing polarity.
3. Push in the side tab of the solar panel cable connector and
pull the connector out of the cable port.
4. Place the connector in the slot on the inside of the repeater
door. Make sure the solar panel cables are tucked inside the
door so that they do not interfere with the interior seal
when the repeater is closed.
Store the solar
panel connector
here when using
lithium batteries
The repeater contacts the network once the new batteries are
installed. The green LED blinks quickly while the repeater
searches for a network to join and then blinks slowly while it
completes the network registration. Once the repeater has
finished joining the network, the green LED turns off and the
blue LED then blinks indefinitely while the repeater is part of
the network.
WARNING: Do not cut open, incinerate, heat above 85°C
(185°F), or recharge the lithium batteries. The batteries may
explode if the repeater is exposed to extreme heat or
conditions that could damage or destroy the battery cases. Do
not mix battery types, either by chemistry or age; batteries may
rupture or explode. Do not dispose of the logger or batteries in
fire. Do not expose the contents of the batteries to water.
Dispose of the batteries according to local regulations for
lithium batteries.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
Industry Canada Statements
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Avis de conformité pour l’Industrie Canada
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1)
l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
To comply with FCC and Industry Canada RF radiation exposure limits for general population, the logger must be installed to provide a separation distance of at least 20cm from
all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
1-800-LOGGERS (564-4377) • 508-759-9500
www.onsetcomp.com/support/contact
© 2018 Onset Computer Corporation. All rights reserved. Onset, HOBO, and HOBOlink are registered
trademarks of Onset Computer Corporation. Mac is a registered trademark of Apple Inc. All other
trademarks are the property of their respective companies.
22249-A
Loading...