Hobie 3179 Instructions For Installation And Operation Manual

#3179 / Page 1 of 5

#3179 - MOTOR MOUNT HOBIE 16.

Instructions for installation and operation of the "go windward" motor mount.
It is recommended that you read through all of the instructions before you begin the
installation. This product has been handcrafted from the finest aircraft aluminum. Careful
steps have been taken to assure you of many years of trouble free operation. The motor
mount has been designed for the MinnKota M35a Electric Fishing Motor. It is
recommended you use this motor. Other motors may work but adjustments may have to be
made to work properly. Whichever motor you use the control box (or motor head) must be
rotated 180° so that the steering and speed control handle are facing the same direction as
the prop as shown in figure 1. "Modified".

Step 1. Remove screw "A" from beneath the motor head in the shoulder as shown in figure

2. Rotate the motor head 180° and replace screw "A".
Step 2. To install motor mount to front dolphin striker, tilt motor mount box as shown in

figure 3. Set the box on the dolphin striker rods and tilt back as shown in figure 4. You
may want to use your knee to assist as this is a very tight fit to keep vibration to a
minimum. Tilt back until clevis pin can be inserted behind the dolphin striker post insert
clevis pin and key as shown in figure 5.

Step 3. Figure 6. press Tilt Lock Button "A" and hold. Pivot transom clamps upward "B"
and release Tilt Lock Button.

Step 4. Loosen Tension Screw "C". Rotate transom clamp 90°. Center transom clamps
between motor head and prop, tighten tension screw "C" shown bottom of figure 7.

Step 5. We are now ready to install the motor to the "Go Windward" motor mount. Hold
the motor horizontally on each side of the transom clamps. Install motor on the backside of
the "Go Windward" motor mount. Lower motor mount down onto the wooden transom as
illustrated by "D" to "E" in figure 7. Tighten clamps securely. We strongly suggest attaching
a safety line from the motor clamps "B" to the hole conveniently drilled in the super
structure of the "Go Windward" motor mount. The motor is now installed on the boat in
storage position (Top figure 7).

Step 6. Install battery by strapping into "Windward" motor mount box. Tighten restraining
strap. Take care to use only a marine deep cycle battery, marine batteries are sealed to
prevent harm to the environment.

Do not connect the motor to the battery at this time!!!!

#3179 - MOTOR MOUNT HOBIE 16.

#3179 / Page 2 of 5

Step 7. To go from the storage position (top figure 7) to a run position (figure 8&9). This
procedure should be done in the water and on the boat. We recommend that you practice
this procedure several times next to shore.

Always make sure the electrical leads are disconnected while adjusting the motor

1. Leaning over the forward crossbar on the prop side of the motor, take firm hold of the
motor shaft.

2. While firmly holding on to the motor shaft, reach through the tramp lacing and loosen
tension lock screw.

3. Slide the shaft until the motor head is against the transom clamp (see figure 8). The
motor has a tendency to twist. Make sure motor head and prop remain parallel to the
tramp. Through the lacing, tighten the tension locking screw.

4. While firmly holding on to the motor shaft, reach through tramp lacing, push and hold
down the Tilt Lock Button. Be careful not to pinch your fingers! With your arm lower
motor into run position (see figure 9).

5. Adjust (if necessary) for a true forward position.

6. Reverse this procedure to return to the storage position.

Step 8: While motor is in running position (locked straight ahead), you may connect the
battery leads and control the motor speed by reaching between the tramp lacing. You may
now steer the rear rudders.

CAUTIONS:

1. Never leave battery leads connected during installation and de-installation as well as
moving from a storage position to run position and vice versa. The reason for this is
the limited clearance under the tramp may cause motor to turn on damaging the
tramp r causing injury to the operator.

2. Take care not to run aground with the motor in the run position. This will cause
damage to everything and has a tendency to be expensive.

3. Remember the motor head is not designed to be submerged in water.

4. Always leave motor in stored position when sailing. Motor or sail, but don't do both!

5. This product was not designed for use in heavy air! This could cause damage to the
motor, motor mount or boat. IF it is howling, what do you need a motor for anyway?