PRODUCT CODE: 1108Z
Instruction Manual
and Tuning Guide
RACING ELECTRIC BOAT
RACING ELECTRIC BOAT
Before beginning assembly, please read these instructions thoroughly!
Always keep this instruction manual ready at hand for quick reference, even after completing the assembly.
Scale fiberglass composite stepped racing boat
Hull Length
Beam
Height
822mm
325mm
130mm
WWW.HOBBYKING.COM
Notice of rights
All rights reserved. No part of this manual may be reproduced or transmitted in any
form by any means. Electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission.
PRODUCT CODE: 1108Z
2 11
WWW.TFLHOBBY.COM
1. 不能将模型长时间放在阳光下直接暴晒。
2. 不要将此模型驶近高压输电线、无线电铁塔，或者其他有无线电波管制的区域。
3. 做好防水工作，不要让水或其他液体接触到任何电气部分，包括马达、遥控器、伺服电路、电子调速器等，并有效地用密封胶带将船舱盖密
封。
4. 模型船应该存放在阴凉干燥的地方，湿度高的地方可能令模型加速锈蚀。
5. 保持船身干净清洁，不要让灰尘、油污接近船身和电气部分。
6. 运输过程请保持船体的平稳，剧烈的颠簸、摇晃和硬物的撞击会导致船身和零部件的损坏。
7. 除了必要的零部件，船舱内不能留有任何异物。
8. 请不要将手和其他物体靠近高速旋转的螺旋桨、外转子无刷电机的外壳，这些都会使你受到不必要的伤害。
9. 刚刚停航的马达和电池都有一定热量，为防烫伤应避免触摸这些地方。
1. 不要在人群密集的地方操控快艇，包括公众海滨浴场，公众游泳池和其他一些水上会所，任何有船只行驶的
主航道，因为在模型的安全问题上你负有完全的不可推卸的责任！！！
2. 在模型的放航前要做好船只的拯救打捞措施，因为你的船只很有可能在湖中停航。
3. 在风急浪涌或潮汐高涨的天气请不要让模型下水，这时水面下很可能有强大的暗流，你不但要做好船只的保
护工作还要为自身的安全多作考虑，避免失足落水。
警 告
WARNING
1. Do not operate boats in crowded places, including public bathing beaches, public swimming-pools, near water clubs and the
main channels which ships sail in. You are entirely responsible for the safe operation of your boat.
2. Please make sure you have the means to recover your boat in the event of it getting stranded on the water.
3. Please do not operate your boat when there is strong winds or strong tidal currents You should not only pay attention to your
boat but you also need to protect yourself from falling in the water.
1. Do not expose the model boat to the sun for long periods of time.
2. Please keep the boat away from high voltage transmission lines, radio towers or area's where you may experience radio interference.
3. Ensure the hull is kept watertight at all times. Do not allow water or liquids to get to any of the electrical parts including motor, receiver,
servo, electronic speed controller etc.. Ensure the top is sealed to the hull at all times you are using the boat with a good waterproof tape.
4. The boat should be stored in a cool, dry place. If you have used the boat in salt water then it must be washed thoroughly in clean fresh water
and dried before storing.
5. Keep the hull clean, keep the hull and the electrical part clean from dust and oil residue.
6. Please keep the boat balanced during transport. Rough handing or being hit by a heavy object in the boot of a car can cause the hull and
parts damaged.
7. Please keep hands and fingers away from the rotating propeller and the outer of the brushless motor to prevent unnecessary injury.
8. To prevent burning please do not touch the motor or battery directly after running, the motor especially will be hot to touch, allow to cool.
简 介
INTRODUCTION
注意事项
ATTENTION
WARNING
警 告
Waterproofing tape
防水胶带
WHEEL RIGHTR
Rudder
WHEEL LEFT
WHEEL STRAIGHT
左转 右转中位
安装船舱盖
基 本 控 制
INSTALLING THE HATCH
BASIC CONTROLS
Before use, switch on the transmitter and then connect the battery in the boat.
Seal the hatch to the hull using 4 strips of waterproof tape.
出航前接通电源，将船舱盖盖好，并用防水胶带源舱盖四周密封，并保证无渗漏。
Thank you for purchasing our model product. This boat" Libero" has a high power brushless motor, the hull is manufactured
from fiberglass and is a perfect scale model of the full size boat, even the CG (Center of gravity) is the same as the actual boat.
With clean, dynamic lines it will quickly become your favorite model boat and can also be used in international competitions.
Through careful research and development the power train of the brushless motor and propeller have been chosen and designed
to give the ultimate performance. They have been developed to bring you an unprecedented model boating experience.
感谢阁下对天富龙模型产品的信赖与支持，libero(自由人）无刷动力赛艇是适合中级和刚接触遥控模型的遥控模型爱好者操控和玩
乐。libero(自由人）的船体是根据大型竞赛船船体hydroplane等比例缩放而成，使用玻璃钢工艺精心制作，为爱好者提供一个造型优美、充满动
感与激情的船体，并配合强大的无刷电机系统，令操控者领略赛场上的兴奋和无与伦比的速度！当经过适度升级改造， libero(自由人）无刷动力
赛艇无论动力和操控性能都会达到一个新台阶，更令你得到前所未有的新体验。
We hope that you will enjoy the Libero and will have a lot of fun using it, especially if you race it in competitions. Please keep the
instruction manual for future reference.
请记住，这是一款非常仿真的比例遥控模型，不但外观相近，零件的复杂度和操控性和真船非常接近。我们希望这产品会给你带来hydroplane
级别真实赛艇的刺激和娱乐休闲的感受。驾驭该产品需要比较全面的专业知识，所以你需要仔细阅读这本使用说明书及注意事项，如果你是一名
新手或者第一次接触遥控模型，请在组装、操控模型前寻求富有经验的模型爱好者、模型店的帮助，以令商品的性能完美发挥。请保留本手册，
以供将来参考。
10 3
WWW.TFLHOBBY.COM
A
F.
I.
组装调试说明书
木制展示船座
工具套装
受信机天线管
B. Hull
船体
C. Cabin cover
船舱盖
D. Rudder
E.
推进器
舵
G.
H.
扎带
Other：
稳定鳍片
Stability fins
Cable ties
Wooden Display Stand Tool set
Propeller
Rx antenna tube
Waterproofing tape
防水胶带
标准的遥控设备：2 channel radio with 1 servo for R/C models. 2频道2伺服R/C遥控设
备。
请检查你的伺服器的尺寸是否符合安装要求
适合的伺服器尺寸
约36mm
approx. 36mm
约20mm
approx. 20mm
约40mm
approx. 40mm
Stick type
杆式遥控
Wheel type
枪式遥控
AA-规格电池8个（发射机用）
锂聚合物电池 X1
2200mAh
11.1V
快速充电器
Philips Screwdriver
Hobby Knife
Needle Nose Pliers
Wire Cutters Epoxy Glue Instant CA Glue
Scissors
十字螺丝刀
尖嘴钳
(Epoxy B)
(Epoxy A)
剪刀
钢丝钳模型刀
CA
双组分环氧胶 CA瞬间粘合胶
电子调速器
AAAA
or
Please check the size of your servo as shown below
for nstallation requirements.
Electronic speed controller
Standard radio control equipment
或
8 pieces AA battery(for transmitter)
Lithium-polymer battery *1
20C
Lithium Battery Charger
INCLUDED ITEMS
包装内容
NECESSARY ACCESSORIES (PURCHASE SEPARATELY)
必要配件（选购）
TOOLS REQUIRED 需要使用的工具
10
电源插头在船只出航前连接，注意极性。
Li-Po Battery
完成
Cut off excess.
拉紧扎带并剪切多余部分。
扎带
稳定鳍片
安装电池
3*8mm screw 1
Washer 1
Fins 1
2.5mm Hex driver
2.5mm内六角扳手
Instruction manual
And tuning guide
Use cable ties to fasten the battery and remove the excess part.使用
扎带将电池紧固并将多余部分裁切。
Li-poly rechargeable battery must be purchased separately!
锂电池另外购买包装内不包含。
Tension
plugs
4 9
WWW.TFLHOBBY.COM
进水口
Hull
船体
Propeller
螺旋桨
Rudder
方向舵
出水口
Water cooling discharge
ESC
Motor
出水口
Water cooling
discharge
各部位概述
MODEL OVERVIEW
布 局
LAYOUT
电 子 调 速 器
电 子 调 速 器
接 收 机
E S C
Cut off excess.
拉紧扎带并剪切多余的部分。
RECEICER
RECEIVER
ELECTRONIC SPEED CONTROLLER
水冷管
扎 带
Cable ties
接 收 机
接收机与司服器的连接请参阅所选器材的使用手册。
Connect at per radio instruction manual.
A
B
C
c
b
a
B
A
C
c
b
a
c
b
a
提示：
和
连接时，调整任意一根线的连接可以改变电机的旋转方向。
完 成
Water Cooling Intake
进水口
Water Cooling Intake
出航前连接
Motor
ESC
连接
连接
受信机
Connector
Connector
Receiver
Rudder Servo
方向控制司服器
电池
Battery
马达
Connect before sailing
电路连接CONNECTION DIAGRAM
Water-cooled tube
, Use these wires to connect the ESC
to the brushless motor.
Notice: Change over any 2 wires to
reverse rotation of motor.
8 5
WWW.HOBBYKING.COM
Servo arm must be 90 degrees to the pushrod.
8-10mm
INSTALLING THE RUDDER SERVO
Cable ties
Cut off excess.
Cut off excess.
Hex driver
1.5mm
Hex driver
2.5mm
Steering Stick
Turn model to left or
right.
Steering Trim
Adjusts the steering in
small increments so
the model will run
straight.
Power Switch
Battery Level Indicator
Two LED display to indicate battery voltage level.
If the Red led flashes, replace batteries.
Antenna
Servo Reversing Switch
Throttle Stick
Control the speed of
the model and
movement forward
and backward.
Throttle Trim
Adjusts the throttle in
small increments so
the model will not
move at neutral.
Battery Cover
See enclosed information.
ESC SET
TRANSMITTER OVERVIEW
BOAT MAINTENANCE
ring Stic
k
l to left
o
r
Antenn
a
Batt
e
Drive line
1. Loosen the motor coupler set screws for the flex cable.
2. Slide the flex cable with marine grease.
3. Lubricate the flex cable with marine grease.
4. Lubricate the drive ball bearings with a light oil for bearings.
5. Reassemble the drive and wipe away any excess grease and oil.
10mm
WATER COOLING INTAKE
Motor coupler set screw
Use high quality marine grease to
lubricate the flexi cable.
Tension
Feed the pushrod through the rubber bellows and connect to
the servo.
6 7
Drill holes with the specified
diameter (2 mm)
WWW.HOBBYKING.COM
2.5mm
Hex driver
Instant CA Glue
2
BOAT STAND
INSTALLING THE PROP
1
Pay attention here
Pay attention here
Make sure the servo is
centered
INSTALLING THE RUDDER
Rudder
1
1
1
1
1
INSTALLING THE RUDDER SERVO
完 成
Ensure smooth non binding movement while assembling.
Aluminum screws
Stainless steel screws
Stainless steel nuts
3mm
3mm
3mm
1
Stainless steel nuts
4mm
The order of assembly
PROPS
The aluminum screw will shear when collisions
happen, this is to protect the rudder from damage. Do not
use screws made of stronger material.
Remove the 3 unused arms
Loading...