Hobart Food Machines HUV3P Installation Manual

HUV SERIES DELI DISPLAY CASES

MODELS

HUV3P ML-132080 (3-PAN, FULL-SERVICE) HUV4P ML-132081 (4-PAN, FULL-SERVICE) HUV5P ML-132082 (5-PAN, FULL-SERVICE)

HUV DISPLAY CASE

HUV7P ML-132084 (7-PAN, FULL-SERVICE)

701 S. RIDGE AVENUE

TROY, OHIO 45374-0001

937 332-3000

www.hobartcorp.com

– 1 –

FORM 35505 (May 2004)

TABLE OF CONTENTS

GENERAL 3 INSTALLATION 4

Unpacking 4

ASSEMBLY 5

Installation of the Side and Center Glass Panels 5 Raise the Front Glass (Customer Side) 5 Installation of Seal Strips for Front Glass Doors (Model HUV7) 5 Install the Glass Panels 5 Installation of the Black Seal Strips 6 Installation of the Sliding Glass Doors 6 Installation of Adjustable Frame and Trays 7 Lower the Front Glass (Customer Side) 7 Installation of the Cutting Board (Optional) 7 Installation of the Base (Optional) 7 Installation Codes and Standards 8 Electrical Connection 8 For HUV Models Provided With Bases With Casters 9 Location 9 Plumbing Connection 10 Water Quality 10 Drain Connection 11 Before First Use 11

OPERATION 12

Full-Service Deli Display Case & Controls 12 Power On Display Case (Full-Service) 13 Automatic Water Level Fill 13 Temperature Controller (Full-Service) 14 Programming the Well Temperature (Full-Service) 14 Memory (Full-Service) 15 Preheat (Full-Service) 15 Loading Food Product into the Display Case 15

SHUTDOWN 15

End of the Day 15

CLEANING 16

End of Day 16

Monthly 18 MAINTENANCE 19 TROUBLESHOOTING 20

Full-Service Cases 20

– 2 –

INSTALLATION, OPERATION AND CARE OF

HUV SERIES DELI DISPLAY CASES

SAVE THESE INSTRUCTIONS

GENERAL

The HUV, Hobart Ultra-View, series of deli display cases hold hot food products at regulated temperatures maintaining both freshness and quality. The display cases feature electronic temperature regulation of the well heat and air stream. Quality stainless steel, clear/mirrored tempered glass and 0 to 10 degree adjustable pan frame work together to provide the customer with an Ultra-View of hot deli products.

• Full-Service cases include adjustment of humidity.

• Combinations of HUV cases can be placed next to each other to provide a variety of pan configurations.

• Display cases accept all standard size pans.

• As options, the display case can be mounted on a base and / or can be equipped with a cutting board.

Proper installation, usage, and maintenance of your deli display case is important. Please read this entire manual and carefully follow all of the instructions provided.

– 3 –

INSTALLATION

Before installing, check the electrical service to make sure it agrees with the specifications on the machine data plate, located on the operator side of the display case.

UNPACKING

Immediately after unpacking the deli display case, check for possible shipping damage. If the deli display case is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.

Remove all vinyl paper from the stainless steel surfaces of the display case and any tape from the glass and steel surfaces.

Unpack the parts that need to be assembled:

HUV3P HUV4P HUV5P HUV7P

Full- Full- Full- Full-

Service Service Service Service

Parts shipped inside the unit and packed separately

Center divider glass panel N/A N/A N/A N/A

Side glass panels 2222

Black glass seal strips 2222

Sliding doors 2224

Long divider bars 2346

Short divider bars 3457

Seal Strip (transparent) N/A N/A N/A 1

Parts shipped separately (optional)

Painted Base Assembly (assembly instructions 1111

included)

Cutting Board Assembly 1111

– 4 –

ASSEMBLY

INSTALLATION OF THE SIDE AND CENTER GLASS PANELS CAUTION: Handle glass panels with care to avoid breakage. The side and center glass panels

are tempered safety glass. If the edges of the glass panels scrape against stainless steel, concrete or other hard surfaces, breakage may occur.

NOTE: Proper installation of the glass seal strips on full-service cases is important to maintain proper

heat and humidity levels inside the case.

RAISE THE FRONT GLASS (CUSTOMER SIDE)

• Raise the front glass (customer side). The door is easier to open when held on the corner and pulled up. Glass stays up by itself.

INSTALLATION OF SEAL STRIPS FOR FRONT GLASS DOORS (Model HUV7) A transparent seal strip must be installed between

the two front glass panels on the customer side on model HUV7P. Place the seal strip on the left piece of glass (Fig. 1) such that the flap rests on the right piece of front glass (Fig. 1). The seal strip closes the gap between the two glass panels.

GLASS

INSTALL THE GLASS PANELS

1. Position the side of glass panel in the groove on the LEFT side of the case (Fig. 2).

2. Carefully slide the side glass panel toward the rear (operator side) of the display case taking care to avoid breakage.

3. Ensure the side glass is completely seated and held in place by the angled track in the rear of the case.

4. Repeat steps 1 through 3 for the RIGHT side of the case.

SEAL STRIP

Fig. 1

Fig. 2

– 5 –

INSTALLATION OF THE BLACK SEAL STRIPS NOTE: The black rubber strips seal the side glass to the front glass. They are necessary to hold

humidity and heat in the full-service case. It is important that the lip of the rubber seal strip faces toward the inside of the case (Fig. 3).

Fig. 3 Fig. 4

• Full-Service case: Install the black glass seal strip on the LEFT side and RIGHT glass panels.

Make sure the lip of the glass seal strips faces toward the inside of the case (Fig. 4).

INSTALLATION OF THE SLIDING GLASS DOORS

1. Insert the top of either door in the top inner track (Fig. 5).

2. Place the bottom of the first door onto the bottom inner track.

3. Insert the top of the second door in the top outer track.

4. Place the bottom of the second door onto the bottom outer track.

Fig. 5

– 6 –

+ 14 hidden pages