HM Electronics HS6000 Users Manual
Transmit
OPERATING INSTRUCTIONS
POWER ON: Press and release the power button on the inside of the headset
housing, shown in Figure 1. A voice message in the earpiece will say “Headset #,
Battery Full/Half or Low” and the power light on the opposite side of the earpiece will
go on (See Figure 2).
POWER OFF: Press and hold the power button on the inside of the headset
earpiece for approximately 3 seconds. A voice message in the earpiece will say
“Headset off,” and the power light on the opposite side of the earpiece will go off.
Power
Light
Light
Figure 1
VOLUME UP: Lightly press the “VOL” up-arrow
button on the side of the earpiece. Each time it is
pressed, a short beep will be heard in the earpiece.
VOLUME DOWN: Lightly press the “VOL” down-
arrow button on the side of the earpiece. Each time it is
pressed, a short beep will be heard in the earpiece.
Figure 2
CONFIGURE HEADSET: Start with power OFF and press any of the following button combinations while
powering the unit ON. Immediately release all buttons after pressing the power button. All of these settings have
associated voice prompts when applying the setting. Please listen to confirm desired setting:
• Hands Free (HF) on / off – Press and hold “B” and UP arrow to turn on HF. Press and hold “B” and
DOWN arrow to turn HFoff.
• Auto HF (AHF) – Press “A1” (or A2) and the UP arrow to turn on the Auto HF mode. Set the base Xcvr
switch K1-3 to on. When you power the unit off AHF mode is not saved.
• Language selection – Press and hold “A1” and the DOWN arrow to toggle between English and another
language. Doing this again toggles back to first language.
• Registration to Base – Set base to accept registration and power up HS6000 while holding “B”. Hold the
HS6000 within 2 meters of the base. (Must be done before use, see Wireless I/Q operation manual)
• Play Status – Press “A2” and DOWN arrow buttons. (e.g. “Headset #, Battery Full/Half/Low,
English/Espanol, Hands-free on/off, firmware version #”)
If you have questions regarding the HS6000, please call HM Electronics, Inc. at (800)848-4468.
DRAFT October 3, 2005 DRAFT
button.
TO TALK TO CUSTOMERS: With your fingertip
(not your fingernail), press and release either the A1 or the
A2 button according to the instructions below, and speak into the
microphone. When you have finished talking to the customer, press
the A1 or A2 button again. The headset will automatically stop
transmitting when the car drives away.
TO TALK TO OTHER CREW MEMBERS: Press and hold
the B button near the microphone, shown in Figure 3, and speak into
the microphone. Release the button when you finish speaking.
Figure 3
Single-Lane Operation
(one base station for one speaker post)
(two base stations for two speaker posts)
Hands-Free (HF) Mode: Hands-Free (HF) Mode:
* Alert tone (single beep) sounds in headset, then customer
at speaker post or menu board can be heard.
* Adjust customer’s voice level in headset if necessary.
* Press and release A1 or A2 button to speak and listen to
customer. You will see microphone boom tip light up.
* Press and release A1, A2 or B button to end communication
with customer. Microphone boom tip light will go out.
* Press and release A1 or A2 button if you want to speak to
the customer again. You will see microphone boom tip light
up.
* If customer drives away from speaker post or menu board,
headset automatically stops transmitting microphone boom tip
light will go out.
* Alert tone (single beep for Lane 1, double beep for Lane 2)
sounds in headset, then customer at speaker post or menu
board can be heard.
* Adjust customer’s voice level in headset if necessary.
* Press and release A1 button for Lane 1 or A2 for Lane 2, to
speak and listen to customer. You will see microphone boom
tip light up.
* Press and release A1, A2 (depending on lane) or B button
to end communication with customer. Microphone boom tip
light will go out.
* Press and release A1 button for Lane 1 or A2 for Lane 2, to
speak to the customer again. You will see microphone boom
tip light up.
* To change lanes, press and release the opposite A button.
A voice in the headset will say “Lane 1” or “Lane 2.”
* If customer drives away from speaker post or menu board,
headset automatically stops transmitting. Microphone boom tip
light will go out.
Auto Hands-Free (AHF) Mode: Auto Hands-Free (AHF) Mode:
* Alert tone (single beep) sounds in headset, then customer
at speaker post or menu board can be heard.
* Adjust customer’s voice level in headset if necessary.
* Speak and listen to customer without pressing any buttons.
You will see microphone boom tip light up.
* Press and release A1, A2 or B button to end communication
with customer. Microphone boom tip light will go out.
* Press and release A1 or A2 button if you want to speak to
the customer again. You will see microphone boom tip light
up.
* If customer drives away from speaker post or menu board,
headset automatically stops transmitting. Microphone boom tip
light will go out.
* Alert tone (single beep for Lane 1, double beep for Lane 2)
sounds in headset, then customer at speaker post or menu
board can be heard.
* Adjust customer’s voice level in headset if necessary.
* Speak and listen to customer without pressing any buttons.
You will see microphone boom tip light up.
* Press and release A1, A2 (depending on lane) or B button
to end communication with customer. Microphone boom tip
light will go out.
* Press and release A1 button for Lane 1 or A2 for Lane 2, to
speak to the customer again. You will see microphone boom
tip light up.
* If customer drives away from speaker post or menu board,
headset automatically stops transmitting. Microphone boom tip
light will go out.
Push-To-Talk (PTT) Mode: Push-To-Talk (PTT) Mode:
* Alert tone (single beep) sounds in headset, then customer
at speaker post or menu board can be heard.
* Adjust customer’s voice level in headset if necessary.
* Press and hold A1 or A2 button to speak to customer. You
will see microphone boom tip light up.
* Alert tone (single beep for Lane 1, double beep for Lane 2)
sounds in headset, then customer at speaker post or menu
board can be heard.
* Adjust customer’s voice level in headset if necessary.
* Press and hold A1 button to speak to customer in Lane 1;
A2 to speak to customer in Lane 2.
* To change lanes, press and release the opposite A
A voice in the headset will say “Lane 1” or “Lane 2.”
Dual-Lane Operation
Loading...