HM-420L/820L/2116L HD-DVR
Digital Video Recorder Instructions
~ Directory~
Chapter 1 Hard Disk Installation (Standard shipping products not include hard
disk) ………………………………………………………………………………...4-6
Chapter 2 Panel Appearance ……………….………………………………………7
2-1 Front Panel Controls ……………………………………………………………7
2-2 Rear Panel Connectors ……………………………………………………….....8
Chapter 3 Live, Playback Operations ………………………………………….…..9
3-1 Remote Control Instructions in LIVE Mode …………………………………..9
3-2 Operating Instructions of Right-Click Mouse Icon in Rapid Functional in
LIVE Mode; Table 3-2-1, Table 3-2-2, Table 3-2-3, Table 3-2-4, Table 3-2-5, Table 3-2-6 Table 3-2-7 Table 3-2-8……………………………………..………..10-16
Chapter 4 The Main Menu Setup ………………………………………………....17
4-1Camera Setup ……………………………….…………………………………..18
4-2 Event Setup ……………………………….…………………………………….19
4-2-1Motion Setup ………………………………………………………………..20
1
4-2-2 Sensor Setup ………….………………………………………………………21
4-3 Recording Setup ………………………………………………………………..22
4-3-1Sequence Setup …………….…………………………………………………23
4-3-2 Video Quality and Frame Rate Setup ………………………………………24
4-4 Alarm Setup …………………………………………………………………..25
4-5 Hard Disk Management Setup ………………………………………………..26
4-5-1HDD Information …….………………………………………………………27
4-6 Networking Setup ………………………………………………………………28
4-6-1 Networking Connection ……………………………………………………..29
4-6-1-1 Local Area Network ……………………………………………………….29
4-6-1-2 DHCP ……………………………………………………………………….30
4-6-1-3 PPPoE ………………………………………………………………………31
4-6-1-4 3G …………………………………………………………………………...32
4-6-2 Advanced Setup ……………………………………………………………...33
4-6-3 HTTP Setup …………………………………………………………………..34
4-6-4 DDNS Setup …………………………………………………………………..35
4-6-5 EMAIL Setup ………………………………………………………………...36
4-6-6 VPN Setup ……………………………………………………………………37
4-6-7 FTP Setup …………………………………………………………………….38
4-6-8 SMS Setup ……………………………………………………………………39
4-6-9 Push Notification Setup ……………………………………………………...40
4-7 Data Backup and System Tools ……………………………………………….41
4-8 System Setup ……………………………………………………………………42
4-8-1 Display Setup …………………………………………………………………43
4-8-2 Time/ Date Setup …………………………………………………………….44
4-8-2-1 Change Date/ Time Setup …………………………………………………45
4-8-2-2 Daylight saving Time Setup ……………………………………………..45
4-8-2-3 Internet Time Setup ……………………………………………………..46
4-8-3 User Account Setup ………………………………………………………..47
4-8-3-1 Permission Setup ………………………………………………………...48
4-8-3-2 Control Relay Setup ……………………………………………………….49
4-8-3-2-1 Relay Timer Setup ……………………………………………………....49
4-8-4 Device Setup ………………………………………………………………….50
2
4-9 EXIT Mani Menu Options …………………………………………………….50
Chapter 5 Backup and Playback Search ………………………………………….51
5-1 Backup Setup ……………………………………………………………….51-52
5-1-1 DVF Player Usage ……………………………………………..................53-54
5-2 Playback Search Setup ………………………………………………………...55
5-2-1 Time Search …………………………………………………………………..56
Chapter6 Network Remote Control ………………………………………………57
6-1 Application Software Installation and Setup ……………………………..57-59
6-2 Do Remote Monitoring through IE …………………………….................60-61
6-3 Do Remote Monitoring through LIVE JPEG (Monitor Function only) ..62-64
6-4 Application Software and IE Operation ……………………………………...65
Chapter7 Remote Connection of Mobile Application and DVR ………………...66
7-1 Mobile Software and Operation with DVR Networking (iPhone Software Installation and Operation & AquilaDVR Software Installation)……………..66-71
7-2 Mobile Software and Operation with DVR Networking (Google Android
Phone Software Installation & Operation) ……………………………………72-77
3
Chapter 1 Hard Disk Installation
( Standard shipping products not include hard disk)
Step 1 : Remove the three screws in rear case, as the following figure at circle
marked. (420L /820L /2116L)
Step 2 : Remove a screw in the right case, as the following figure at circle
marked.
Step 3 : Remove a screw in the left case, as the following figure at circle marked.
4
Step 4 : Open the chassis cover along the direction of the arrow (upward)
Step 5 : Put Hard Disk on the Hard Disk plate and fix it with four screws as the
picture indicated. Connect SATA & Power wire to Hard Disk.
5
Step 6 : Put the cover back and fix it with 5 screws as Step 1-3 indicated.
Note: After installation, please initialize Hard Disk before starting to record. For
more detailed information, please check out User Manual System Tools for reference.
6
Chapter 2 Panel Appearance
(1) IR Display
IR Enable
(2) USB Port
USB port (for USB，please use rear USB port
for mouse device)
(3) LED- Power
DVR power on
(4) REC
REC : DVR recording ( or setup schedule and
open the recording function )
(5) LED - Alarm
Alarm on alarm event, signal break and motion
detection
(6) LED- LAN
Lan is working
2-1 Front Panel Controls
7
2-2 Rear Panel Connectors (420L / 820L / 2116L)
(1) Video In
BNC input port for cameras (total of 16 jacks)
(2) CVBS OUT
Video output
(3) Audio Out
Audio signals RCA output port (Corresponding CH1)
(4) Audio In
Audio signals RCA input port (1~16)
(5) VGA
VGA port
(6) HDMI
High resolution multimedia interface
(7) USB 2.0 Port
USB device port
(8) IR
IR receiving elongated holes
(9) ALARM OUT
RS485
(10) LAN
Network port
(11) DC 12V
DC 12V power jack
(12) Audio Out
Recording
Audio signals RCA output port (Recording)
8
Chapter 3 Live, Playback Operations
ICON
DESCRIPTION
REC
Start/ Stop recording
Mute
Live audio is on/off
Play
Entering play back mode
1-9
Switch to full screen displaying channels
Freeze
On/ Off screen freezing function
Menu
Enable/ Disable setup menu
PTZ
PTZ mode
Zoom
Enter/ Delete Zoom mode
The area can be moved and zoomed by arrow keys or the mouse
ESC
Enter/ Return Menu
Enter
Enter
FF
Fast forward. There are six speeds: 2x, 4X, 8X, 16X, 32X and
64X.
Stop
Stop play/ Stop play back
RF
Rewind fast. There are six speeds: 2x, 4X, 8X, 16X, 32X and 64X.
Pause
Pause
Split
Switch to split windows
Polling
Start auto channel change. Channel can be cycled change by
seconds setting and display in full screen.
PIP
On/ Off picture in picture. Switch channel by mouse clicking.
Lock
On/ Off Lock Key
Zoom in
Zoom in. Using the arrow keys to move the Zoom in area.
Zoom out
Zoom out. Using the arrow keys to move the Zoom out area.
Focus in
Focus in
Focus out
Focus out
Ctrl 1,2,3,4
On/ Off 1~4 relay
DVR 1,2,3,4
Switch DVR ID 1~4
In LIVE mode, all of channel screens and live sounds can be monitored and
screens can be changed and operated. The following describes the real-time
monitoring mode, the operation of remote controller and mouse and screen’s
prompts
3-1 Remote Control Instructions in LIVE Mode
9
3-2 Operating Instructions of Right-Click Mouse Icon in
ICON
DESCRIPTION
Camera setup – Show, auto, channel change, PTZ control, image control, audio control
Main menu. Clicking this icon will bring up the following nine menu
icons.
Event setup - OSD motion setup, sensing device setup
Recording setup - OSD motion, sound record, video record, alarm record, schedule record
Alarm setup – Event, time setup, image broken setup
HDD - Loop record, residual rate alarm, capacity state
Networking setup – LAN, DHCP, PPPOE, HTTP, DDNS, EMAIL,
VPN, FTP setup
Data backup - Interface option, system event clear, system update setup
System setup – Name, language, VGA resolution, menu lock, display
option, user, relay setup
Leave = “ESC”
System disk information – Version, IP, MAC, HDD capacity
Zoom in/ out = “Zoom” AUX 1 ~ 8 (signal screen only)
PTZ control= “PTZ” (signal screen only)
Sound control – On/ Off live sound
= “Polling”
= “PIP”
Rapid Functional in LIVE Mode
Table 3-2-1
10
Table 3-2-2
After Right - Clicking Mouse, Graphical Icons Displays in LIVE
Mode
ICON
DESCRIPTION
~
CH1~CH16 signal screen
Record = “REC” On/ Off record
Stop = “FREEZE” Screen stop
Play = “PLAY” Playback
Freeze-screen is frozen
Lock = “LOCK”
Backup - Information backup
Quad display
Nine display
Sixteen display
11
Table 3-2-3
Graphical Icons Displays on the Bottom Right of the Window in
Remote Mode
ICON
DESCRIPTION
Remote snapshot - Take picture on camera and store
(pre-archived folder - My Documents
Folder/DVRData/Snapshot)
Select archive folder - Select the folder to store the photo and
video
Full screen - Switch to full screen
HQ/ LQ image quality switch
Remote recording - Record and store
(pre-archived folder - My Documents
Folder/DVRData/Snapshot)
Remote shortcut bar narrow
NOTE!
Before IE browser into the "remote control model" will be required to change
the ActiveX controls to prompt under Tools / Internet Options / Security / Custom
Level / Download the ActiveX controls unsigned
Table 3-2-4
In LIVE mode, switch to PLAYBACK Mode by pressing “PLAY”
button. The control panel will appear on the bottom right of the
window. The control panel can be moved by mouse.
12
The control panel description in PLAYBACK mode
ICON
DESCRIPTION
Snapshot - Turn the current screen into the “Image” and store in
USB device. Image will be stored in computer on remote mode
Rewind fast. There are six speeds : 2x, 4x, 8x, 16x, 32x and 64x.
Pause/ Signal screen playback
Normal speed playback
Stop
Normal speed play
Pause/ Signal screen play
Fast forward. There are six speeds : 2x, 4x, 8x, 16x, 32x and 64x.
ICON
DESCRIPTION
Forward 24 Hours
Time Search
Backward 24 Hours
Timeline
Table 3-2-5
Shuttle Function. Move the cursor to the bottom of the screen to display
13
Table 3-2-6 Graphical Icons Displays in Remote Mode
ICON
DESCRIPTION
USB device detected
HDD not detected
Lock is on - Need code to unlock
Network connecting
Recoding - Icon appears when one of the cameras is recording
Event occur - Appear on alarm, lost channel, motion detected
Recording - The icon appears in signal screen when the camera is
recording
Live audio is on in signal screen
Live audio is off in signal screen
OSD (motion detection) is on in signal screen
Relay off
Relay on
Shows the current hard disk space has been used.
Table 3-2-7
Select signal screen and switch to PTZ mode by pressing “PTZ” button. The control panel will appear on the bottom right of the window.
14
Remote controller operation under PTZ mode
ICON
DESCRIPTION
Arrow Keys
Up, down, left, right
Enter Key
Executive function
PTZ Arrow Keys
Move PTZ camera
Zoom In
Let PTZ camera closer
Zoom Out
Let PTZ camera further
Mouse operation under the PTZ mode
ICON
DESCRIPTION
Patrol setup - Select location by arrow keys and press Enter
to start patrol.
Patrol select - Pre-set number N (1~255)
Move to pre-set number N
Delete pre-set number
Automatically patrol
Zoom in
Zoom out
Iris in
Iris out
15
Focus out
Focus in
1
RS485A_D+ (TX+)
2
RS485A_D- (TX-)
3
ALARM OUT_COM
4
ALARM OUT_N.C
5
ALARM OUT_N.O
Table 3-2-8
DVR-HM-2116D Relay-Control Wiring Diagram
16
Chapter 4 The Main Menu Setup
Enter the setup menu first time, please choose the login account, and then enter
the password. Administrator default password is "123456."
Verify password, if correct will enter the setup menu
17
4-1 Camera Setup
ICON
DESCRIPTION
1 – 4/8/16
Each channel can be set dependently
Camera Screen Display
Live screen On/ Off
Polling Mode
On/ Off
Polling Mode Time
On/ 0~100 seconds (the time that screen stays)
Camera Title Setup
Customize the camera channel name
PTZ Enable
On/ Off
No. of PTZ
PTZ number (0~255)
Baud Rate
Select the PTZ camera transmission speed (2400,
4800, 9600, 19200)
PTZ Protocol
Support : PELCO-D, PELCO-P, HME PDZ,
UNITED-D
Brightness
Brightness adjustment (from value1-255)
Contrast
Contrast adjustment (from value 1-255)
Hue
Color adjustment (from value 1-255)
Saturation
Chroma adjustment (from value 1-255)
Volume
Channel 1 can adjust the volume and record volume
HDLY
Picture tuning (right/ left)
VDLY
Picture tuning (up/ down)
18
4-2 Event Setup
ICON
DESCRIPTION
Motion Setup
Enter motion detection setup
Sensor Setup
Enter sensing device setup
19
4-2-1 Motion Setup
ICON
DESCRIPTION
1 – 4/8/16
Each channel can be set dependently
Enable
Switch on or off the motion detection function
Buzzer Alarm
On/ Off
Sensitivity
Set up sensitivity from value 1 to 10 for each channel. The higher value you set the higher sensitivity it
will be.
Motion Area Setup
Enter to motion area setup
Apply All
On/ Off
Specific Screen Detection
On/ Off
Full Time Detection
Full-time or schedule detection select
20
4-2-2 Sensor Setup
ICON
DESCRIPTION
Popup
On/ Off
NO.
On/ Off
Polarity
Low= “Start”, High= “+12V start”
All Enable
NO = All sensing device on
All Disable
NO = All sensing device off
All Low
Sensitivity all low
All High
Sensitivity all high
Full Time Detection
Full-time or schedule detection select
21
4-3 Recording Setup
ICON
DESCRIPTION
1 – 4/8/16
Each channel can be set independently
OSD Position X
Setup OSD X axis
OSD Position Y
Setup OSD Y axis
OSD Position Setup
Setup OSD axis
Record Sound
On/ Off
HDD Circulate Record
On/ Off
Alarm Recording Time
1~60 seconds
Recording Mode
Manual/ Schedule record 1~6
Schedule Record Setup
Schedule record on
Quality& Frame Rate Setup
Turn on quality& frame rate setup
22
4-3-1 Sequence Setup
ICON
DESCRIPTION
Stop REC
Enter
Motion REC
Enter
Full Time REC
Enter
SEQ = Schedule Record
Manual/ Schedule record 1~6
All Same
Recording mode all the same
23
4-3-2 Video Quality and Frame Rate Setup
ICON
DESCRIPTION
View Normal/ View
Event
Select recording mode
No. 1-4/8/16
Check/ Uncheck the box enable/ disable selected
channel recording
Resolution
Select recording resolution :
NTSC : 480x240, 960x240, 960x480
Quality
Select quality : below basic/ basic/ normal/ high/
highest
FPS
Select recording frame rate
Auto
Assign each channel with its maximum accessible
fps
24
4-4 Alarm Setup
ICON
DESCRIPTION
Alarm Event Record
On/ Off
Video Loss Detect
On/ Off
Video Loss Alarm Time
0~99 seconds
HDD and System Error Alarm
On/ Off
No HDD Alarm
On/ Off
Specified Screen Time
0~99 seconds
Alarm Time Setup
Sensing, motion, locking, alarm time
Buzzer
0~99 seconds
Relay
0~99 seconds
25
4-5 Hard Disk Management Setup
ICON
DESCRIPTION
Cycle Record
On/ Off
Hard Disk Information
Hard disk information instruction
Hard Disk Format Setup
Hard Disk Format
26
4-5-1 HDD Information
ICON
DESCRIPTION
Ver = Version
DVR current software version
IP Address
DVR network IP address. If DVR doesn’t connect, it will show “Network not connected”
MAC ADDR = MAC Address
Mac Address of DVR
NO. = Number
The number of the hard disk
Name
The name of the hard disk
Capacity
The capacity of the hard disk
Status
Utilization rate
The percentage of used HDD
Shows HDD current status
27
4-6 Networking Setup
ICON
DESCRIPTION
Connectivity
Connectivity setup (PPPoE, DHCP, LAN, 3G)
HTTP Setup
Enter HTTP setup menu
DDNS Setup
Enter DDNS setup menu
Email Setup
Enter Email setup menu
VPN Setup
Enter VPN setup menu
FTP Setup
Enter FTP setup menu
SMS Setup
Enter SMS setup menu
Push Notification Setup
Enter push notification setup menu
28
4-6-1 Networking Connection (Four Connection Methods
ICON
DESCRIPTION
Local IP Address
Enter IP address provided by ISP
Mask
Enter IP address of subnet mask provided by ISP
Gateway
Enter IP address of gate way provided by ISP
DDNS
Enter DNS address provided by ISP.
NOTE : The correct DNS address must be entered for
DDNS function
Available)
4-6-1-1 Local Area Network
Select LAN for network connection, the following information is required.
29
4-6-1-2 DHCP
When DHCP is selected, IP address will be assigned by DHCP server automatically.
30
4-6-1-3 PPPoE
ICON
DESCRIPTION
User Name
Enter user name provided by ISP
Password
Enter password provided by ISP
Select PPPOE for network connection, the following information is required.
31
4-6-1-4 3G
ICON
DESCRIPTION
3G Card
Enter 3G card number provided by ISP
PIN Code
Enter PIN code provided by ISP
APN
Enter APN provided by ISP
Dial-up Number
Enter dial-up number provided by ISP
32
4-6-2 Advanced Setup
ICON
DESCRIPTION
User Name
Enter user name provided by ISP
Password
Enter password provided by ISP
Local IP Address
Enter IP address provided by ISP
33
4-6-3 HTTP Setup
ICON
DESCRIPTION
Startup
HTTP
Check to enable HTTP server. Users can remotely access into
the DVR over the network, if the HTTP function is activated.
HTTP Port
Enter a valid port value from 1 up to 65000. The default value
is 80.
Auto
Assign each channel with its maxima accessible fps.
No.
Check/ Uncheck the box enable/ disable selected channel remote monitoring function.
Quality
Set up record quality. There are below basic, basic, normal,
high, highest.
FPS
Higher quality requires higher network bandwidth. Setup
record FPS
34
4-6-4 DDNS Setup
ICON
DESCRIPTION
Enable DDNS
Enable/ Disable DDNS function
DDNS Server
Enter the registered SMTP server :
DYNDNS.ORG, NO-IP.ORG
Host Name
Enter the completed registered SMTP Server.
(Including username + Server)
If the user name is hme264 and you choose DYNDNS.ORG as
your server, you should enter : hme264. DYNDNS.ORG
User Name
Enter DDNS server user name
Password
Enter DDNS server password
35
4-6-5 EMAIL Setup
ICON
DESCRIPTION
Enable Email
Notification
On/ Off E-MAIL notification function
SMTP Server
Enter to set up SMTP server name
(varies according to the user)
SMTP Port
Normally it is 25
User Name
Enter to set up user name
Password
Enter to set up password
Trigger Mode
Enter to select events to send out e-mail notifications when
below circumstances happen : motion and voss (video loss).
Sender
EMAIL
Enter to set up sender e-mail address
Receiver
EMAIL
Enter to set up e-mail addresses for up to 6 receivers individually.
36
4-6-6 VPN Setup
ICON
DESCRIPTION
Enable VPN
On/ Off VPN
Server Address
Enter address
User Name
Enter to set up user name
Password
Enter to set up password
MPPE Encryption
On/ Off encryption
37
4-6-7 FTP Setup
ICON
DESCRIPTION
Server
FTP server account
FTP Port
Normally it is 21
User Name
Enter to set up user name
Password
Enter to set up password
38
4-6-8 SMS Setup
ICON
DESCRIPTION
SMS Server
Enter SMS server
Server Address
Enter server address
Link Port
Normally it is 80
User Name
Enter to set up user name
Password
Enter to set up password
39
4-6-9 Push Notification Setup
ICON
DESCRIPTION
Enable Notification
On/ Off enable notification
Image Lead Time (sec)
0~30 seconds
Remove All Mobile Registered
Whether to remove
40
4-7 Data Backup and System Tools
ICON
DESCRIPTION
Data Backup
Enter “Data Backup” menu
CD/ DVD Data Backup
Enter “CD/ DVD Data Backup” menu
Save DVR Setup to USB
Enter “Backup to USB” menu
Set the DVR to a USB device. USB will appear the
file.
Get DVR Setup from USB
Enter “Download Setup from USB Settings”
menu. The USB device settings loaded to the DVR
Restore Factory Settings
Enter “Reduction Factory Settings” menu
Reduction the system settings to the initial value
Clean Event Record
Enter “Reset The System Event” menu. Remote
all event record in DVR
System Update
Enter “System Update” menu. Through USB update DVR software. Before Update, please backup
DVR settings and restart DVR after updating.
USB Drive Format
Enter “USB Drive Format” menu. Click “YES” to
clean all data of the USB and wait until “format
successfully” showing
Boot Logo Change
Enter “Boot Logo Change” to change Logo
41
4-8 System Setup
ICON
DESCRIPTION
DVR Name
Display name for application software log remotely into the DVR.
Language
Setup OSD display language
VGA Resolution
1024x768 or 1920x1080
Video Type
Auto or manual
Menu/ Key Lock
On/ Off
DVR ID Number
0~63
Display Setup
Enter display setup
Time/ Date Setup
Enter time/ date setup
User Account
Enter user account setup
Control Relay Setup
Enter relay setup
Device Setup
Enter device setup
42
4-8-1 Display Setup
ICON
DESCRIPTION
Time Display
On/ Off date and time display
Camera Info. Display
On/ Off camera information
Record Info. Display
On/ Off record information
Control Relay Display
On/ Off control relay
Border Display
On/ Off border
Time Position
up~ down
Disk and Status Info. Display
On/ Off disk and status info. display
AV Output Deflicker
On/ Off AV output Deflicker
Border Col-
or
Red
0~255
Green
0~255
Blue
0~255
43
4-8-2 Time/ Date Setup
ICON
DESCRIPTION
Date Format
year/ month/ date ~ date/ month/ year ~ month/
date/ year
Select Time Zone
Adjust to Greenwich Mean Time (GMT)
Change Date/ Time
On/ Off change date/ time
Daylight Saving Time Setup
On/ Off daylight saving time
Internet Time Setup
On/ Off network time
44
4-8-2-1 Change Date/ Time Setup
ICON
DESCRIPTION
Daylight Saving Time Mode
On/ Off
Select the year/ month/ date and press “Yes.”
4-8-2-2 Daylight Saving Time Setup
45
4-8-2-3 Internet Time Setup
ICON
DESCRIPTION
Automatically
Synchronize
Check to enable DVR automatic synchronization function.
Effective by this option selected, DVR will automatically
synchronize the time upon rebooting or by every 24 hours
after booting.
Update Now
Effectively, date and time show on DVR will immediately
correspond with those in internet server.
46
4-8-3 User Account Setup
ICON
DESCRIPTION
Number No.
Check to activate the user’s account
User Name
Setup username
Password
Set up password for each user
Permission
Set up Permissions for each user
Change Admin Password
Change administrator’s password
The account setup menu is used to provide role-based permission independently
setting for each user (maximum of 32users) to access DVR over network. The
default admin account and password is “admin” and “123456”
47
4-8-3-1 Permission Setup
ICON
DESCRIPTION
Camera Setup
On/ Off
Record Setup
On/ Off
Hard Disk Setup
On/ Off
Backup Setup
On/ Off
Stop Record
On/ Off
PTZ
On/ Off
Remote Relay Operation
On/ Off
Event Setup
On/ Off
Alarm Setup
On/ Off
Network Setup
On/ Off
System Setup
On/ Off
Playback
On/ Off
Network
On/ Off
Hosting Talk
On/ Off
Remote and Playback Mask
Ch1 ~ Ch4/8/16 option
48
4-8-3-2 Control Relay Setup
ICON
DESCRIPTION
No.
Choose relay 1,2,3,4
Unstable Time
0 is the solid-state (1~255 seconds)
Time Control
Enter the setup menu
4-8-3-2-1 Relay Timer Setup
There are 8 sections. Start the relay by setting the time and choose ON/OFF.
49
4-8-4 Device Setup
Volume control : (1-16)
4-9 EXIT Main Menu Option
50
Chapter 5 Backup and Playback Search
5-1 Backup Setup
Video data can be backed up from DVR hard disk. To do so, USB device must
plug into DVR USB port before entering to the backup menu.
The backup file, DVF file, can be played by “DVFPLAYER.”
NOTE : Use the USB flash backup, the system will automatically copy
"DVFPLAYER" to the USB
51
ICON
DESCRIPTION
Start Time
The start time of backup file
End Time
The end time of backup file
Backup Channel
Choose CH1 – CH4 CH1-CH8 CH1-CH16
Backup Destination
Select USB or PC as the backup device
Free Space
The available space in the backup device
Request Space
Show the size of the backup file
Pause the Live Image
On/ Off
52
5-1-1 DVF Player Usage
ICON
DESCRIPTION
DVR Disk
Play hard disk EXT3 file format.
Open
Open the file.
To AVI
Turn AVI.
Step 1 : Install “DVR play” software to your PC. You can get “DVR play” file
from the CD with DVR Packing.
PS : When you using USB to backup file, DVRplay.exe will copy to USB with the
backup file automatically.
Step 2 : Perform “DVR player”
53
Step 3 : Click “open” to choose and star a DVR backup file.
Step 4 : “DVR play” software will plays the backup file automatically.
54
5-2 Playback Search Setup
ICON
DESCRIPTION
Time Search
Enter time search menu
Event Search
Event search menu
55
5-2-1 Time Search
Time Search can search for the specific time of recording data to playback. Press
“Enter” or left click on the desired date to playback. Note that dates with recording data are marked with a red square “□” System will start playing back
according to the date you selected. Calendar will be shown by using mouse to
click on “year” and “month.”
Click “date” to display recording time of that specific date with time bar. You
can change time (hour/minute/second) or click on a specific time of time bar by
mouse then press “ok.” DVR will playback the selected recording data.
56
Chapter 6 Network Remote Control
“DVRemoteDesktop” and IE6.0 or above can allow you to remotely access and
control the DVR from PC.
P.S. Operation system currently supports Windows XP SP2 and above and Win-
dows Vista, Windows 7.
6-1 Application Software Installation and Setup
Step 1 : Enter the IP address of DVR in IE browser. Actual address is depending
on the setup of on-site DVR.
Step 2 : Windows as below will show up. Please enter the user name and pass-
word. Default user name and password is admin/123456. Actual user name and
password depend on the setup of on-site DVR setting.
57
Step 3 : Click on the link to start downloading the AP software.
Step 4 : Run or save our AP software
58
Step 5 : If you choose to run the software, Start window will be shown up. Please
enter information of login DVR : IP, Port, Username and Password, or choose
“Play Recorded File” to open backup files in your PC.
Step 6 : You’ve logged into the DVR
59
6-2 Do Remote Monitoring through IE
Step 1 : Enter the IP address of DVR in IE browser. The address appeared in this
image is only for demonstration. Actual address is depending on the setup of
on-site DVR.
Step 2 : Windows as below will show up. Please enter the user name and password. Default user name and password is admin/123456. Actual user name and
password depend on the setup of on-site DVR setting.
60
Step 3 : Click on “Internet Explorer 6, 7, and 8” to start downloading the AP
software. (The first option is for IE view; please refer to next chapter for more
information)
P.S. There will be IE connection security issue when clicking this link for the first
time. Please refer to index II for Remote Monitoring IE ActiveX Control Installation Instruction.
Step 4 : DVR images appear
61
6-3 Do Remote Monitoring through LIVE JPEG (Monitor
Function only)
Step 1 : Enter the IP address of DVR in IE browser. The address appeared in this
image is only for demonstration. Actual address is depending on the setup of
on-site DVR.
Step 2 : Windows as below will show up. Please enter the user name and pass-
word. Default user name and password is admin/123456. Actual user name and
password depend on the setup of on-site DVR setting.
62
Step 3 : Click on “LIVE JPEG”
Step 4 : DVR images appear
63
P.S. : Only for viewer, without any operation function
64
6-4 Application Software and IE Operation
CPU
Intel Pentium 4 above
RAM
512M above
OS
Microsoft Windows 7, Windows Vista, Windows XP SP2 above
VGA Card
Need to support DirectX 9.0 (above) – Note 1
Antivirus
Software
IE and AP connection need PORT 80 (according to HTTP PORT
settings)
Others
DirectX 9.0 above
Table 6-4-1 System Requirements for AP Software
Note 1:
Known VGA card that support DirectX9.0 currently:
NVIDIA : Geforce FXseries, Geforce 6series, Geforce 7series, Geforce 8series, Ge-
force 9series, Geforce 200series, etc.
Or visit :
http://en.wikipedia.org/wiki/Comparison_of_Nvidia_graphics_processing
_units
ATI : Radeon R300series, Radeon R400series, Radeon R500series, Radeon
R600series, Radeon R700series, Radeon HD 3xxx IGPseries, Mobility
Radeonseries (9500 above), Mobility Radeon Xseries, Mobility Radeon
HDseries, or FireGL Vseries etc.
Or visit :
http://en.wikipedia.org/wiki/Comparison_of_ATI_graphics_processing_units
SiS : SiS 67Xseries, or SiS 77Xseries etc.
Or visit : http://www.sis.com/support/support_compare.htm
Intel : 91Xseries, 94Xseries, 96Xseries, G3Xseries, or G4Xseries, etc.
Or visit : http://en.wikipedia.org/wiki/Intel_GMA
65
Chapter 7 Remote Connection of Mobile Appli-
cation and DVR
7-1 Mobile Software and Operation with DVR Networking
iPhone Software Installation and Operation
AquilaDVR Software Installation
Step 1 : Connect mobile phone to the internet and unlock
Step 2 : Open and execute App Store program
66
Step 3 : Key in software name “Aquila”
Step 4 : Display Software introduction and show “FREE” to download, click upper right “FREE” to star downloading
67
Step 5 : Select upper right “Install” to star downloading APP
When Login User Name is displayed, key in register Apple ID : Username/ password
Step 6 : After the installation is completed, it will show “AquilaDVR”
68
Step 7 : Add new DVR information
For first time connection, must enter and save DVR information. Select bottom
left “ ”
Step 8 : Select bottom left “Add” to add new DVR information
69
Step 9 : Key in DVR name, address & port, user name, password then select
“save” for saving
Step10 : After saving, it shows “Host Name”, select “Host Name” then click
“GO”
70
Step 11 : The logging time depends on network bandwidth. When login successfully, it shows DVR live view
71
7-2 Mobile Software and Operation with DVR Networking
Google Android Phone Software Installation & Operation
Step 1 : Connect the mobile phone to the internet
Step 2 : Open “Market”
72
Step 3 : Select upper right “Search”
Step 4 : Key in Software name “Aquila” and search
73
Step 5 : Select “Aquila” and “Install”
Step 6 : Select “OK” for authorization
74
Step 7 : Check “Notifications” for installation progress
Step 8 : After installation completed, it shows the download file “Aquila DVR”
75
Step 9 : Execute “AquilaDVR”
Step 10 : Add new DVR information for connecting DVR. For first time connection, must enter and save DVR information. Select bottom left “New”
76
Step 11 : After saving, it shows “DVR”, click DVR twice continously to log in
Step 12 : The logging time depends on network bandwidth. When login successfully, it shows DVR live view.
77
Loading...