HMC Electronics 1631-16S User Manual

G3 Flux Remover

1631

Flux removers (defluxers) remove flux residues and other contaminants left by manufacture, rework, or repair of printed circuit boards.
Residues from higher, leadfree temperatures are more baked on and harder to clean. G3, Ecoline and PrecisionV flux removers have
been proven very effective at removing fluxes baked on at leadfree temperatures.

Microcomponents and fine pitch leads are delicate and easily damaged, so brushing and scrubbing should be avoided if possible. Both
G3, Ecoline and PrecisionV have a powerful spray and strong solvent that blasts off residues and cleans areas under components that a
brush cannot touch.

Non-flammable & powerful cleaner

Flux removers (defluxers) remove flux residues and other contaminants left by manufacture, rework, or
repair of printed circuit boards. Residues from higher, lead-free temperatures are more baked on and
harder to clean. G3®, Ecoline™ and Precision-V™ flux removers have been proven very effective at
removing fluxes baked on at lead-free temperatures. Micro-components and fine pitch leads are
delicate and easily damaged, so brushing and scrubbing should be avoided if possible. Both G3,
Ecoline and Precision-V have a powerful spray and strong solvent that blasts off residues and cleans
areas under components that a brush cannot touch. Patented defluxer formulated to be powerful and
nonflammable, yet economical. Eliminates brushing and scrubbing, saving time and materials.

Powerful cleaner
Non-flammable
Non-ozone depleting
Safe on electronics
Rapid evaporation
Zero residue
Safe on most plastics
EPA SNAP approved
Proven effective for lead-free processes

Product Packaging

1631-16S

G3 Flux Remover

16 oz

12 units/case

1631-5S

G3 Flux Remover

5 oz

12 units/case

Instructions

Make sure opening of sprayhead is pointing toward surface to be cleaned. Hold can 15-20 cm away. Direct spray to saturate soiled surface. A TechBrush® (2000 Series)
may be utilized to help in the removal of heavy soils. When used as a general cleaner, start at top of area to be cleaned using a sweeping motion, and spray the area
slowly, working towards the bottom. To clean in hard to reach areas, insert extension tube in sprayhead to direct spray. Allow components to dry completely before
applying current. For flat surface cleaning, saturate a lint-free TechClean® Twillwipe (2357) or Purwipe™ (2355) and wipe surface with cloth. Rotate the cleaning side of the
wipe periodically and re-saturate.

page 1 / 2

Techspray - US office, P.O. Box 949,

Amarillo, TX 79105-0949,
Tel. [phone], Toll-free 800-858-4043
Fax [phone], [e-mail]

Documentation Provided By HMC Electronics

33 Springdale Ave. Canton, MA 02021

http://www.hmcelectronics.com

[phone]

Chemical & Physical Properties

Appearance Clear, colorless liquid
Odor Faint ethereal odor
Flash Point none
VOC (EPA) 64%
VOC (CARB) 75%
Boiling Point 39°C (102.2°F)
Density

Chemical Composition

CHEMICAL NAME CAS #

1,1,1,2,2,3,4,5,5,5-decafluoropentane
(HFC-4310mee)

138495-42-8

1,2-transdichloroethylene 156-60-5
Ethanol 64-17-5
1,1,1,2-Tetrafluoroethane 811-97-2
Carbon dioxide 124-38-9

Environmental Policy

Techspray is committed to developing products to ensure a safer and cleaner environment. We will continue to meet and sustain the regulations of all federal, state and
local government agencies.

Resources

Techspray products are supported by a global sales, technical and customer services resources.

For additional technical information on this product or other Techspray products in the United States, call the technical sales department at 800-858-4043, email
[e-mail] or visit our web site at: www.techspray.com.

North America

Techspray
P.O. Box 949
Amarillo, TX 79105
800-858-4043
email: [e-mail]

Europe

ITW Contamination Control BV
Saffierlaan 5
2132 VZ Hoofddorp
The Netherlands
[phone]
email: [e-mail]

Countries Outside US

Call to locate a distributor in your country

Important Notice to Purchaser/User: The information in this publication is based on tests that we believe are reliable. The results may vary due to differences in tests type and conditions. We recommend that each
user evaluate the product to determine its suitability for the intended application. Conditions of use are outside our control and vary widely. Techspray's only obligation and your only solution is replacement of
product that is shown to be defective when you receive it. In no case will Techspray be liable for any special, incidental, or consequential damages based on breach of warranty, negligence or any other theory.

page 2 / 2

Techspray - US office, P.O. Box 949,

Amarillo, TX 79105-0949,
Tel. [phone], Toll-free 800-858-4043
Fax [phone], [e-mail]

Documentation Provided By HMC Electronics

33 Springdale Ave. Canton, MA 02021

http://www.hmcelectronics.com

[phone]