HK Audio LUCAS PERFORMER User Manual [en, de, es, fr, it]

Manual 1.0

English
Deutsch
Français
Español

Wichtige Sicherheitshinweise!

Bitte vor Gebrauch lesen und für späteren Gebrauch
aufbewahren!

• Read all of these instructions!

• Save these instructions for later use!

•Follow all warnings and instructions marked on the product!

• Do not use this product near water, i.e. bathtub, sink, swimming pool,
wet basement, etc.

• Do not place this product on an unstable cart, stand or table. The product may
fall, causing serious damage to the product or to persons!

• Slots and openings in the cabinet and the back or bottom are provided for
ventilation; to ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered. This product should
not be placed in a built-in installation unless proper ventilation is provided.

• This product should not be placed near a source of heat such as a stove,
radiator, or another heat producing amplifier.

• Use only the supplied power supply or power cord. If you are not sure of the
type of power available, consult your dealer or local power company.

• Do not allow anything to rest on the power cord. Do not locate this product
where persons will walk on the cord.

• Never break off the ground pin on the power supply cord.

• Power supply cords should always be handled carefully. Periodically check cords
for cuts or sign of stress, especially at the plug and the point where the cord
exits the unit.

• The power supply cord should be unplugged when the unit is to be unused for
long periods of time.

• If this product is to be mounted in an equipment rack, rear support should be
provided.

• This product should be used only with a cart or stand that is recommended by
HK AUDIO

®

.

• Never push objects of any kind into this product through cabinet slots as they
may touch dangerous voltage points or short out parts that could result in risk
of fire or electric shock. Never spill liquid of any kind on the product.

• Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing
to qualified service personnel.

• Clean only with dry cloth.

• Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for the safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.

• Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:

• When the power cord or plug is damaged or frayed.

• If liquid has been spilled into the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally when the operating instructions are
followed.

• If the product has been dropped or the cabinet has been damaged.

• If the product exhibits a distinct change in performance, indicating a need of
service!

• Adjust only these controls that are covered by the operating instructions since
improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to
normal operation.

• Exposure to extremely high noise levels may cause a permanent hearing loss.

• Individuals vary considerably in susceptibility to noise induced hearing loss, but
nearly everyone will lose some hearing if exposed to sufficiently intense noise
for a sufficient time. The U.S. Government´s Occupational Safety and Health
Administration (OSHA) has specified the following permissible noise level
exposures:

Duration Per Day In Hours Sound LeveldBA, Slow Response

890
692
495
397
2 100
11/2 102
1 105
1/2 110
1/4 or less 115

• According to OSHA, any exposure in excess of the above permissible limits
could result in some hearing loss.

• Ear plug protectors in the ear canals or over the ears must be worn when operating
this amplification system in order to prevent a permanent hearing loss if exposure
is in excess of the limits as set forth above. To ensure against potentially
dangerous exposure to high sound pressure levels, it is recommended that all
persons exposed to equipment capable of producing high sound pressure levels
such as this amplification system be protected by hearing protectors while this
unit is in operation.

•Fuses: Replace with IEC 127 (5x 20 mms) type and rated fuse for best
performance only.

TO PREVENT THE RISK OF FIRE AND SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO MOISTURE OR RAIN. DO NOT OPEN CASE;
NO USER SERVICE-ABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Version 1.0 10/2004

• The unit has been built by HK AUDIO

®

in accordance with IEC 60065 and left
the factory in safe working order. To maintain this condition and ensure non­risk operation, the user must follow the advice and warning comments found in
the operating instructions. The unit conforms to Protection Class 1 (protectively
earthed).

•HK AUDIO®ONLY GUARANTEE THE SAFETY, RELIABILITY AND EFFICIENCY
OF THE UNIT IF:

• Assembly, extension, re-adjustment, modifications or repairs are carried out by
HK AUDIO®or by persons authorized to do so.

• The electrical installation of the relevant area complies with the requirements
of IEC (ANSI) specifications.

• The unit is used in accordance with the operating instructions.

• The unit is regularly checked and tested for electrical safety by a competent
technician.

WARNING:

• If covers are opened or sections of casing are removed, except where this can
be done manually, live parts can become exposed.

• If it is necessary to open the unit this must be insulated from all power sources.
Please take this into account before carrying out adjustments, maintenance,
repairs and before replacing parts.

• The appliance can only be insulated from all power sources if the mains
connection is unplugged.

• Adjustment, maintenance and repairs carried out when the unit has been opened
and is still live may only be performed by specialist personnel who are authorized
by the manufacturer (in accordance with VBG 4) and who are aware of the
associated hazards.

• Loudspeaker outputs which have the IEC 417/5036 symbol (Diagram 1, below)
can carry voltages which are hazardous if they are made contact with. Before
the unit is switched on, the loudspeaker should therefore only be connected
using the lead recommended by the manufacturer.

• Where possible, all plugs on connection cables must be screwed or locked onto
the casing.

• Replace fuses only with IEC127 type and specified ratings.

• It is not permitted to use repaired fuses or to short-circuit the fuse holder.

• Never interrupt the protective conductor connection.

• Surfaces which are equipped with the "HOT" mark (Diagram 2, below), rear
panels or covers with cooling slits, cooling bodies and their covers, as well as
tubes and their covers are purposely designed to dissipate high temperatures
and should therefore not be touched.

• High loudspeaker levels can cause permanent hearing damage. You should
therefore avoid the direct vicinity of loudspeakers operating at high levels.
Wear hearing protection if continuously exposed to high levels.

MAINS CONNECTION:

• The unit is designed for continuous operation.

• The set operating voltage must match the local mains supply voltage.

• The unit is connected to the mains via the supplied power unit or power cable.

• Power unit: Never use a damaged connection lead. Any damage must be rectified
by a competent technician.

•Avoid connection to the mains supply in distributor boxes together with several
other power consumers.

• The plug socket for the power supply must be positioned near the unit and
must be easily accessible.

PLACE OF INSTALLATION:

• The unit should stand only on a clean, horizontal working surface.

• The unit must not be exposed to vibrations during operation.

• Keep away from moisture and dust where possible.

• Do not place the unit near water, baths, wash basins, kitchen sinks, wet areas,
swimming pools or damp rooms. Do not place objects containing liquid on the
unit - vases, glasses, bottles etc.

• Ensure that the unit is well ventilated.

• Any ventilation openings must never be blocked or covered. The unit must be
positioned at least 20 cm away from walls. The unit may only be fitted in a rack
if adequate ventilation is ensured and if the manufacturer's installation instruc­tions are followed.

• Keep away from direct sunlight and the immediate vicinity of heating elements
and radiant heaters or similar devices.

• If the unit is suddenly moved from a cold to a warm location, condensation can
form inside it. This must be taken into account particularly in the case of tube
units. Before switching on, wait until the unit has reached room temperature.

• Accessories: Do not place the unit on an unsteady trolley, stand, tripod, base or
table. If the unit falls down, it can cause personal injury and itself become damaged.
Use the unit only with the trolley, rack stand, tripod or base recommended by
the manufacturer or purchased together with the unit. When setting the unit
up, all the manufacturer's instructions must be followed and the setup accessories
recommended by the manufacturer must be used. Any combination of unit and
stand must be moved carefully. A sudden stop, excessive use of force and uneven
floors can cause the combination of unit and stand to tip over.

• Additional equipment: Never use additional equipment which has not been
recommended by the manufacturer as this can cause accidents.

•To protect the unit during bad weather or when left unattended for prolonged
periods, the mains plug should be disconnected. This prevents the unit being
damaged by lightning and power surges in the AC mains supply.

Diagram 1 Diagram 2

•Das Gerät wurde von HK AUDIO®gemäß IEC 60065 gebaut und hat das Werk
in sicherheitstechnisch einwandfreiem Zustand verlassen. Um diesen Zustand
zu erhalten und einen gefahrlosen Betrieb sicherzustellen, muss der Anwender
die Hinweise und die Warnvermerke beachten, die in der Bedienungsanleitung
enthalten sind. Das Gerät entspricht der Schutzklasse I (schutzgeerdet).

• DIE SICHERHEIT, ZUVERLÄSSIGKEIT UND LEISTUNG DES GERÄTES WIRD
VON HK AUDIO®NUR DANN GEWÄHRLEISTET, WENN:

• Montage, Erweiterung, Neueinstellung, Änderungen oder Reparaturen von
HK AUDIO®oder von dazu ermächtigten Personen ausgeführt werden.

• die elektrische Installation des betreffenden Raumes den Anforderungen von
IEC (ANSI)-Festlegungen entspricht.

• das Gerät in Übereinstimmung mit der Gebrauchsanweisung verwendet wird.

WARNUNG:

•Wenn Abdeckungen geöffnet oder Gehäuseteile entfernt werden, außer wenn
dies von Hand möglich ist, können Teile freigelegt werden, die Spannung führen.

•Wenn ein Öffnen des Gerätes erforderlich ist, muss das Gerät von allen Span­nungsquellen getrennt sein. Berücksichtigen Sie dies vor dem Abgleich, vor
einer Wartung, vor einer Instandsetzung und vor einem Austausch von Teilen.

• Ein Abgleich, eine Wartung oder eine Reparatur am geöffneten Gerät unter
Spannung darf nur durch eine vom Hersteller autorisierte Fachkraft (nach VBG

4) geschehen, die mit den verbundenen Gefahren vertraut ist.

• Lautsprecher-Ausgänge, die mit dem IEC 417/5036-Zeichen (Abb.1, s.unten)
versehen sind können berührungsgefährliche Spannungen führen. Deshalb vor
dem Einschalten des Gerätes Verbindung nur mit dem vom Hersteller empfoh­lenen Anschlusskabel zum Lautsprecher herstellen.

• Alle Stecker an Verbindungskabeln müssen mit dem Gehäuse verschraubt oder
verriegelt sein, sofern möglich.

• Es dürfen nur Sicherungen vom Typ IEC 127 und der angegebenen Nennstrom­stärke verwendet werden.

• Eine Verwendung von geflickten Sicherungen oder Kurzschließen des Halters
ist unzulässig.

• Niemals die Schutzleiterverbindung unterbrechen.

• Oberflächen, die mit dem "HOT"-Zeichen (Abb.2, s.unten) versehen sind,
Rückwände oder Abdeckungen mit Kühlschlitzen, Kühlkörper und deren Ab­deckungen, sowie Röhren und deren Abdeckungen können im Betrieb erhöhte
Temperaturen annehmen und sollten deshalb nicht berührt werden.

• Hohe Lautstärkepegel können dauernde Gehörschäden verursachen.
Vermeiden Sie deshalb die direkte Nähe von Lautsprechern, die mit hohen
Pegeln betrieben werden. Verwenden Sie einen Gehörschutz bei dauernder
Einwirkung hoher Pegel.

NETZANSCHLUSS:

• Das Gerät ist für Dauerbetrieb ausgelegt.

• Die eingestellte Betriebsspannung muss mit der örtlichen Netzspannung
übereinstimmen.

• Der Anschluss an das Stromnetz erfolgt mit dem mitgelieferten Netzteil oder
Netzkabel.

• Netzteil: Eine beschädigte Anschlussleitung kann nicht ersetzt werden.
Das Netzteil darf nicht mehr betrieben werden.

•Vermeiden Sie einen Anschluss an das Stromnetz in Verteilerdosen zusammen
mit vielen anderen Stromverbrauchern.

• Die Steckdose für die Stromversorgung muss nahe am Gerät angebracht und
leicht zugänglich sein.

AUFSTELLUNGSORT:

• Das Gerät sollte nur auf einer sauberen, waagerechten Arbeitsfläche stehen.

• Das Gerät darf während des Betriebs keinen Erschütterungen ausgesetzt sein.

•Feuchtigkeit und Staub sind nach Möglichkeit fernzuhalten.

• Das Gerät darf nicht in der Nähe von Wasser, Badewanne, Waschbecken,
Küchenspüle, Nassraum, Swimmingpool oder feuchten Räumen betrieben
werden. Keine mit Flüssigkeit gefüllten Gegenstände -Vase, Gläser, Flaschen
etc. auf das Gerät stellen.

• Sorgen Sie für ausreichende Belüftung der Geräte.

•Eventuelle Ventilationsöffnungen dürfen niemals blockiert oder abgedeckt
werden. Das Gerät muß mindestens 20 cm von Wänden entfernt aufgestellt
werden. Das Gerät darf nur dann in ein Rack eingebaut werden, wenn für
ausreichende Ventilation gesorgt ist und die Einbauanweisungen des Her­stellers eingehalten werden.

•Vermeiden Sie direkte Sonneneinstrahlung sowie die unmittelbare Nähe von
Heizkörpern und Heizstrahlern oder ähnlicher Geräte.

•Wenn das Gerät plötzlich von einem kalten an einen warmen Ort gebracht wird,
kann sich im Geräteinnern Kondensfeuchtigkeit bilden. Dies ist insbesondere
bei Röhrengeräten zu beachten. Vor dem Einschalten solange warten bis das
Gerät Raumtemperatur angenommen hat.

• Zubehör: Das Gerät nicht auf einen instabilen Wagen, Ständer, Dreifuß, Unter­satz oder Tisch stellen. Wenn das Gerät herunterfällt, kann es Personenschäden
verursachen und selbst beschädigt werden. Verwenden Sie das Gerät nur mit
einem vom Hersteller empfohlenen oder zusammen mit dem Gerät verkauften
Wagen, Rack, Ständer, Dreifuß oder Untersatz. Bei der Aufstellung des Gerätes
müssen die Anweisungen des Herstellers befolgt und muss das vom Hersteller
empfohlene Aufstellzubehör verwendet werden. Eine Kombination aus Gerät
und Gestell muss vorsichtigt bewegt werden. Plötzliches Anhalten, übermäßige
Kraftanwendung und ungleichmäßige Böden können das Umkippen der Kombi­nation aus Gerät und Gestell bewirken.

• Zusatzvorrichtungen: Verwenden Sie niemals Zusatzvorrichtungen, die nicht
vom Hersteller empfohlen wurden, weil dadurch Unfälle verursacht werden
können

• Zum Schutz des Gerätes bei Gewitter oder wenn es längere Zeit nicht beauf­sichtigt oder benutzt wird, sollte der Netzstecker gezogen werden.
Dies verhindert Schäden am Gerät aufgrund von Blitzschlag und Spannungs­stößen im Wechselstromnetz.

Abb.1 Abb.2

Important Safety Instructions

Before connecting, read instructions

Important Advice on Safety!

Please read before use and keep for later use!

• L'appareil a été conçu par HK AUDIO®selon la norme IEC 60065 et a quitté
l'entreprise dans un état irréprochable. Afin de conserver cet état et d'assurer
un fonctionnement sans danger de l'appareil nous conseillons à l'utilisateur la
lecture des indications de sécurité contenues dans le mode d'emploi. L'appareil
est conforme à la classification I (mise à terre de protection).

• SURETE, FIABILITE ET EFFICACITE DE L'APPAREIL NE SONT GARANTIS PAR
HK AUDIO®QUE SI:

• Montage, extension, nouveau réglage, modification ou réparation sont
effectués par HK AUDIO®ou par toute personne autorisée par HK AUDIO®.

• L'installation électrique de la pièce concernée correspond aux normes
IEC (ANSI).

• L'utilisation de l'appareil suit le mode d'emploi.

AVERTISSEMENT:

•A moins que cela ne soit manuellement possible, tout enlèvement ou ouverture
du boîtier peut entrainer la mise au jour de pieces sous tension.

• Si l'ouverture de l'appareil est nécessaire, celui-ci doit être coupé de chaque
source de courant. Ceci est à prendre en considération avant tout ajustement,
entretien, réparation ou changement de pieces.

• Ajustement, entretien ou réparation sur l'appareil ouvert et sous tension ne
peuvent être éffectués que par un spécialiste autorisé par le fabricant (selon
VBG4). Le spécialiste étant conscient des dangers liés à ce genre de réparation.

• Les sorties de baffles qui portent le signe IEC 417/5036 (fig. 1, voir en bas)
peuvent être sous tension dangereuse. Avant de brancher l'appareil utiliser
uniquement le câble de raccordement conseillé par le fabricant pour raccorder
les baffles.

•Toutes les prises des câbles de raccordement doivent être, si possible, vissées
ou verrouillées sur le boîtier.

•L’utilisation de fusibles rafistolés ou court-circuites est inadmissible –
seulement: IEC127.

• L'utilisation de fusibles rafistolés ou court-circuites est inadmissible.

• Ne jamais interrompre la connexion du circuit protecteur.

• Il est conseillé de ne pas toucher aux surfaces pourvues du signe "HOT" (fig. 2,
voir en bas), aux parois arrières ou caches munis de fentes d'aération,
éléments d'aération et leurs caches ansi qu'aux tubes et leurs caches.
Ces éléments pouvant atteindre des températures élévées pendant l'utilisation
de l'appareil.

• Les Niveaux de puissance élévés peuvent entrainer des lésions auditives
durables. Evitez donc la proximité de haut-parleurs utilisés à haute puissance.
Lors de haute puissance continue utilisez une protection auditive.

BRANCHEMENT SUR LE SECTEUR:

• L'appareil est conçu pour une utilisation continue.

• La tension de fonctionnement doit concorder avec la tension secteur locale.

• Le raccordement au réseau éléctrique s'effectue avec l'adaptateur ou le cordon
d´alimentation livré avec l'appareil.

• Adaptateur: Un câble de raccordement abimé ne peut être remplacé. L'adapta­teur est inutilisable.

•Evitez un raccordement au réseau par des boîtes de distribution surchargées.

• La prise de courant doit être placée à proximité de l'appareil et facile à atteindre.

LIEU D'INSTALLATION:

• L'appareil doit être placé sur une surface de travail propre et horizontale.

• L'appareil en marche ne doit en aucun cas subir des vibrations.

•Evitez dans la mesure du possible poussière et humidité.

• L'appareil ne doit pas être placé à proximité d'eau, de baignoire, lavabo, évier,
pièce d'eau, piscine ou dans une pièce humide. Ne placez aucun vase, verre,
bouteille ou tout objet rempli de liquide sur l'appareil.

• L'appareil doit être suffisamment aéré.

• Ne jamais recouvrir les ouvertures d'aération. L'appareil doit être placé à 20 cm
du mur au minimum. L'appareil peut être monté dans un Rack si une
ventilation suffisante est possible et si les conseils de montage du fabricant
sont suivis.

•Evitez les rayons de soleil et la proximité de radiateurs, chauffages etc.

• Une condensation d'eau peut se former dans l'appareil si celui-ci est transporté
brusquement d'un endroit froid à un endroit chaud. Ceci est particulièrement
important pour des appareils à tubes. Avant de brancher l'appareil attendre
qu'il ait la température ambiante.

• Accessoires: L'appareil ne doit être placé sur un chariot, support, trépied, bâti
ou table instable. Une chute de l'appareil peut entrainer aussi bien des domma­ges corporels que techniques. Utilisez l'appareil uniquement avec un chariot,
Rack, support, trépied ou bâti conseillé par le fabricant ou vendu en combinai­son avec l'appareil. Les indications du fabricant pour l'installation de l'appareil
sont à suivre, et les accessoires d'installation conseillés par le fabricant sont à
utiliser. Un ensemble support et appareil doit être déplacé avec précaution.
Des mouvements brusques et des revêtements de sol irreguliers peuvent
entrainer la chute de l´ensemble.

• Equipements supplémentaires: Ne jamais utiliser un équipement supplémen­taire n'ayant pas été conseillé par le fabricant, ceci pouvant entrainer des
accidents.

• Afin de protéger l'appareil pendant un orage ou s'il ne doit pas être utilisé
pendant un certain temps, il est conseillé d'enlever la prise au secteur.
Ceci évite des dommages dûs à la foudre ou à des coups de tension dans le
réseau à courant alternatif.

Fig. 1 Fig. 2

• L'apparecchio è stato costruito dalla HK AUDIO®secondo la normativa euro­pea IEC 60065 ed ha lasciato il nostro stabilimento in stato ineccepibile. Per
garantire il mantenimento di tale stato e un utilizzo assolutamente privo di ri­schi l'utente è tenuto ad osservare le indicazioni e gli avvertimenti di sicurezza
contenuti nelle istruzioni per l'uso. L'apparecchio rispecchia il livello di
sicurezza I (collegato a terra).

• Sicurezza, affidabilità e prestazioni dell'apparecchio vengono garantiti dalla
HK AUDIO®solo ed esclusivamente se:

• Montaggio, ampliamento, rimessa a punto, modifiche e riparazioni vengono
eseguite dalla HK AUDIO®stessa o da personale da essa autorizzato.

• Gli impianti elettrici nei locali prescelti per l'uso dell'apparecchio rispondono
alle normative stabilite dall'ANSI.

• L'apparecchio viene utilizzato come indicato nel libretto delle istruzioni per l'uso.

Avvertimenti:

• In caso di apertura di parti di rivestimento o rimozione di parti dell'involucro,
a meno che non si tratti di pezzi rimovibili semplicemente a mano, possono
venire alla luce parti dell'apparecchio conduttrici di tensione.

• Se l'apertura dell'apparecchio dovesse risultare necessaria è indispensabile
staccare precedentemente quest'ultimo da tutte le fonti di tensione. Rispettare
tale misura di prevenzione anche prima di un allineamento, di operazioni di
manutenzione, della messa in esercizio o della sostituzione di componenti
all'interno dell'apparecchio.

• Allineamento, operazioni di manutenzione o eventuali riparazioni dell'appa­recchio in presenza di tensione vanno eseguite esclusivamente da personale
specializzato ed autorizzato, in grado di eseguire tali operazioni evitandone
i rischi connessi.

• Le uscite degli altoparlanti contrassegnate dai caratteri IEC 417/5036 (vedi
illustrazione 1 a fondo pag.) possono essere conduttrici di tensione pericolosa
con cui evitare il contatto. Per questo motivo, prima di accendere l'appa­recchio, collegare quest'ultimo agli altoparlanti servendosi esclusivamente del
cavetto d'allacciamento indicato dal produttore.

•Tutte le spine e i cavi di collegamento devono essere avvitati o fissati all'invo­lucro dell'apparecchio per quanto possibile.

• Utilizzare esclusivamente fusibili del tipo IEC 127 con la indicata corrente no­minale.

• L'utilizzo di fusibili di sicurezza non integri e la messa in corto circuito del
sostegno di metallo sono proibite.

• Non interrompere mai il collegamento con il circuito di protezione.

• Superfici contrassegnate dalla parola "HOT" (vedi illustrazione 2 a fondo pag.),
cosi come griglie di aerazione, dispositivi di raffreddamento e i loro rivestimen­ti di protezione, oppure valvole e i relativi rivestimenti protettivi possono surri­scaldarsi notevolmente durante l'uso e per questo motivo non vanno toccate.

• L'ascolto di suoni ad alto volume può provocare danni permanenti all'udito.
Evitate perciò la diretta vicinanza con altoparlanti ad alta emissione di suono
e utilizzate cuffie protettive in caso ciò non sia possibile.

Alimentazione:

• L'apparecchio è concepito per il funzionamento continuo.

• La tensione di esercizio deve corrispondere alla tensione di rete a cui ci si allaccia.

• L'allacciamento alla rete elettrica avviene tramite alimentatore o cavetto d'ali­mentazione consegnato insieme all'apparecchio.

• Alimentatore: un cavo di connessione danneggiato non può essere sostituito.
L'alimentatore non può più essere utilizzato.

•Evitate un allacciamento alla rete di corrente utilizzando cassette di distribu­zione sovraccariche.

• La spina di corrente deve essere situata nelle vicinanze dell'apparecchio e
facilmente raggiungibile in qualsiasi momento.

Locali di collocamento:

• Opportuno collocare l'apparecchio su una superficie pulita e orizzontale.

• Non sottoporre l'apparecchio in funzione a scosse e vibrazioni.

• Proteggere l'apparecchio per quanto possibile da umidità e polvere.

• Non collocare l'apparecchio vicino ad acqua, vasche da bagno, lavandini, lavelli
da cucina, locali umidi o piscine. Non appoggiare recipienti contenenti liquidi ­vasi, bicchieri, bottiglie, ecc. - sull'apparecchio.

• Provvedere ad una buone aerazione dell'apparecchio.

•Eventuali aperture previste per la ventilazione dell'apparecchio non vanno ne
bloccate, ne mai coperte. L'apparecchio va collocato ad almeno 20 cm di di­stanza dalle pareti circostanti e può essere inserito tra altre componenti di un
impianto solo in caso di sufficiente ventilazione e qualora le direttive di
montaggio del produttore vengano rispettate.

•Evitare di esporre l'apparecchio ai raggi del sole e di collocarlo direttamente
nelle vicinanze di fonti di calore come caloriferi, stufette, ecc.

• Se l'apparecchio viene trasportato rapidamente da un locale freddo ad uno
riscaldato può succedere che al suo interno si crei della condensa. Ciò va
tenuto in considerazione soprattutto in caso di apparecchi a valvole. Attendere
che l'apparecchio abbia assunto la temperatura ambiente prima di accenderlo.

• Accessori: non collocare l'apparecchio su carrelli, supporti, treppiedi, superfici
o tavoli instabili. Se l'apparecchio dovesse cadere a terra potrebbe causare
danni a terzi o danneggiarsi irreparabilmente. Utilizzate per il collocamento
dell'apparecchio supporti, treppiedi e superfici che siano consigliate dal
produttore o direttamente comprese nell'offerta di vendita. Per il collocamento
dell'apparecchio attenetevi strettamente alle istruzioni del produttore, utili­zzando esclusivamente accessori da esso consigliati. L'apparecchio in combina­zione ad un supporto va spostato con molta attenzione. Movimenti bruschi o il
collocamento su pavimenti non piani possono provocare la caduta dell'appa­recchio e del suo supporto.

• Accessori supplementari: non utilizzate mai accessori supplementari che non
siano consigliati dal produttore, potendo essere ciò causa di incidenti.

• Per proteggere l'apparecchio in caso di temporali o nel caso questo non venisse
utilizzato per diverso tempo si consiglia di staccarne la spina di corrente.
In questo modo si evitano danni all'apparecchio dovuti a colpi di fulmine o ad
improvvisi aumenti di tensione nel circuito di corrente alternata.

Illustrazione 1 Illustrazione 2

• El aparato ha sido producido por HK AUDIO®según el IEC 60065 y salió de la
fábrica en un estado técnicamente perfecto. Para conservar este estado y
asegurar un funcionamiento sin peligros el usuario debe tener en cuenta las
indicaciones y advertencias contenidas en las instrucciones de manejo.
El aparato corresponde a la clase de protección l (toma de tierra protegida).

• LA SEGURIDAD, LA FIABILIDAD Y EL RENDIMIENTO DEL APARATO SOLO
ESTAN GARANTIZADOS POR HK AUDIO®CUANDO:

• el montaje, la ampliación, el reajuste, los cambios o las reparaciones se
realicen por HK AUDIO®o por personas autorizadas para HK AUDIO®;

• la instalación eléctrica del recinto en cuestión corresponda a los requisitos
de la determinación del IEC (ANSI);

• el aparato se use de acuerdo con las indicaciones de uso.

ADVERTENCIA:

• Si se destapan protecciones o se retiran piezas de la carcasa, exceptuando si se
puede hacer manualmente, se pueden dejar piezas al descubierto que sean
conductoras de tensión.

• Si es necesario abrir el aparato, éste tiene que estar aislado de todas las
fuentes de alimentación. Esto se debe tener en cuenta antes del ajuste, de un
entretenimiento, de una reparación y de una sustitución de las piezas.

• Un ajuste, un entretenimiento o una reparación en el aparato abierto y bajo
tensión sólo puede ser llevado a cabo por un especialista autorizado por el
productor (según VBG 4) que conozca a fondo los peligros que ello conlleva.

• Las salidas de altavoces que estén provistas de la característica IEC 417/5036
(figura 1, véase abajo) pueden conducir tensiones peligrosas al contacto. Por
ello es indispensable que antes de poner en marcha el aparato; la conexión se
haya realizado únicamente con el cable de empalmes recomendado por el
productor.

• Las clavijas de contacto al final de los cables conectores tienen que estar
atornilladas o enclavadas a la carcasa, en tanto que sea posible.

• Sólo se pueden utilizar fusibles del tipo IEC 127 con la intensidad de corriente
nominal indicada.

• El uso de fusibles reparados o la puesta en cortocircuito del soporte es
inadmisible.

• El empalme del conductor de protección no se puede interrumpir en ningún
caso.

• Las superficies provistas de la característica "HOT" (figura 2, véase abajo),
los paneles de fondo trasero o las protecciones con ranuras de ventilación, los
cuerpos de ventilación y sus protecciones, así como las válvulas electrónicas y
sus protecciones pueden alcanzar temperaturas muy altas durante el funcio­namiento y por ello no se deberían tocar.

• Niveles elevados de la intensidad de sonido pueden causar continuos daños
auditivos; por ello debe evitar acercarse demasiado a altavoces que funcionen
a altos niveles. En tales casos utilice protecciones auditivas.

ACOMETIDA A LA RED:

• El aparato está proyectado para un funcionamiento continuo.

• La tensión de funcionamiento ajustada tiene que coincidir con la tensión de la
red del lugar.

• La conexión a la red eléctrica se efectuará con la fuente de alimentación o con
el cable de red que se entreguen con el aparato.

•Fuente de alimentación: una linea de conexión dañada no se puede sustituir.
La fuente de alimentación no puede volver a ponerse en funcionamiento.

•Evite una conexión de la red eléctrica a distribuidores con muchas tomas de
corriente.

• El enchufe para el suministro de corriente tiene que estar cerca del aparato
y ser de fácil acceso.

SITUACION:

• El aparato debería estar situado en una superficie limpia y totalmente horizontal.

• El aparato no puede estar expuesto a ningún tipo de sacudidas durante su
funcionamiento.

• Se deben evitar la humedad y el polvo.

• El aparato no puede ponerse en funcionamiento cerca del agua, la bañera, el
lavamanos, la pila de la cocina, un recinto con tuberías de agua, la piscina o en
habitaciones húmedas. Tampoco se pueden poner objetos llenos de líquido ­jarrones, vasos, botellas, etc. - encima de él.

• Procure que el aparato tenga suficiente ventilación.

• Las aberturas de ventilación existentes no se deben bloquear ni tapar nunca.
El aparato debe estar situado como mínimo a 20 cm de la pared. El aparato
sólo se puede montar en un rack, si se ha procurado la suficiente ventilación y
se han cumplido las indicaciones de montaje del productor.

•Evite los rayos del sol directos así como la proximidad a radiadores, electro­radiadores o aparatos similares.

• Si el aparato pasa repentinamente de un lugar frío a otro caliente, se puede
condensar humedad en su interior. Esto se debe tener en cuenta sobretodo en
los aparatos con válvulas electrónicas. Antes de poner en marcha el aparato se
debe esperar hasta que éste haya adquirido la temperatura ambiental.

• Accesorios: el aparato no se puede colocar encima de carros, estantes, trípodes,
soportes o mesas inestables. Si el aparato se cae puede causar daños perso­nales y se puede estropear. Coloque el aparato sólo en un carro, rack, estante,
trípode o soporte recomendado por el productor o que se le haya vendido junto
con el aparato. En la instalación se deben seguir las indicaciones del productor
así como utilizar los accesorios recomendados por el mismo para colocarlo
encima. El conjunto del aparato con el pedestal se debe mover con mucho
cuidado. Un paro brusco, la aplicación de una fuerza desmesurada o un suelo
irregular puede ocasionar la caida de todo el conjunto.

• Piezas adicionales: no utilice nunca piezas adicionales que no estén recomen­dadas por el productor, ya que se podrían provocar accidentes.

• Para protejer el aparato de una tormenta o si no se supervisa ni utiliza durante
algún tiempo, se debería desconectar la clavija de la red. Así se evitan daños en
el aparato a causa de un rayo y golpes de tensión en la red de corriente alterna.

Figura 1 Figura 2

Conseils de Securite Importants!

Priere de lire avant l'emploi et a conserver pour uti­lisation ulterieure!

Importanti avvertimenti di sicurezza!

Leggere attentamente prima dell'uso e conservare per
un utilizzo successivo:

¡Indicaciones de seguridad importantes!

¡Léanse antes de utilizar el aparato y guardense para
so uso posterior!

L.U.C.A.S PERFORMER Manual 1.0

Welcome to the HK AUDIO
family!

Thank you for choosing an HK AUDIO product.

L.U.C.A.S PERFORMER consists of two satellites and
a subwoofer equipped with a power amp and all the
electronics required to drive the bass bin and
satellite. Painstakingly fine-tuned to match the
speakers for the best possible sound and superior
impulse response, the electronic circuitry protects it
from overloads and makes this system so very easy
to operate.

You don't have to worry about tweaking frequencies
and finessing levels, all you have to do is set up the
system’s components, connect the signal-routing
and power cords, and you're ready to roll.

An HK AUDIO active system is so much more than
merely a pair of active cabinets on tripods; it is an
end-to-end sound-reinforcement solution consisting
of subwoofer, satellites and meticulously matched
circuitry.

Our engineers developed new technologies to satisfy
the stringent requirements of such an advanced
system. These unique features make this active
HK AUDIO sound reinforcement system stand out
from the crowd.

Best wishes from the HK AUDIO team. We hope you
enjoy your L.U.C.A.S PERFORMER system as much
as we enjoyed developing it!

WARRANTY

Register your L.U.C.A.S PERFORMER using the
enclosed warranty cards to extend your warranty to
five years free of charge!
Use the convenient ONLINE REGISTRATION option
at www.hkaudio.com

.
If you are unable to register online, please fill out
the enclosed warranty card completely and mail or
fax it to us.

Important note: Be sure to register the subwoofer
and satellites separately using one registration
card each.

The registration is only valid if the warranty registra­tion card is filled out and returned to HK AUDIO or
the device is registered via the Internet within 30
days of purchase. We are also interested in learning
where our products are used and by whom. This in­formation will help us design future products. Your
data is of course protected by privacy laws.

Thank you!

HK AUDIO

®

Technical Service
Postfach 1509
D-66959 St. Wendel, Germany

Contents

1 L.U.C.A.S PERFORMER System Components . .6

2Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

3Connections and Control Features . . . . . . . . . . .7

4 Tips and Tricks . . . . . . . . . . . . . . . . . . . . . . . . . .8

5 L.U.C.A.S PERFORMER Accessories . . . . . . . . .9

6Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .9

7Technical Data . . . . . . . . . . . . . . . . . . . . . . . . .11

5

Easy setup and handling for less pre-gig stress

Like all HK Audio active rigs, L.U.C.A.S PERFORMER
was conceived as a cohesive system comprising
painstakingly matched components. This rig was
engineered for easy portability and swift set-up.
Operation is simple, with no complicated tweaking
required.

• Genuine system design: All components are
precision-matched.

• Swift set-up & easy operation to save time

• Less stress = more fun + better music

Digital amping for enhanced efficiency and dynamic
response

With an efficiency rating topping the 90% mark,
Class-D digital power amps are substantially smaller,
lighter, and more compact than conventional amps.
The reduced thermal load on components enhances
reliability, while the far faster slew rate and higher
damping factor audibly enhances the speed and
precision of the system’s dynamic response.

Making the most of sonic energy with MonoTilt™

The newly developed, integrated MonoTilt ™ pole
mount allows sound energy to be utilized with great
efficiency. Troublesome ceiling reflections are
minimized; the sound is clearer, tighter, and more
focused. Beyond that, the cabinet is stabilized at
its center of gravity - no wobbling, tilting, or
unintentional turning.

Multi-band limiting and companding

Several matched limiters and companders are fine­tuned and optimised to process different frequency
ranges. This speaker-independent approach to signal
processing results in natural-sounding dynamic
response across the entire frequency spectrum and
produces a powerful yet finely balanced sonic image.

Subsonic filter

The integrated subsonic filter cuts unwanted ultral­ow frequencies. Infra sub-bass signals resulting from
stage rumble, wind or similar sources place heavy
demands on the power amp to render frequencies so
low that they exceed the useful range of the speaker
cabinet. The subsonic filter protects the amp from
these frequencies, thereby increasing the entire
system’s output power.

• Protects both power amps and speakers from
harmful ultralow frequencies.

• Enables cleaner and tighter bass response and
higher output levels.

OFR™ Optimized Frequency Response Technology

HK AUDIO

®

’s unique OFR™ technology deliver
commanding yet well-balanced sound at every level.
It corrects for non-linear frequency response in the
speaker components at the same time as it
compensates for the way human hearing works at
varying levels.

• Fine-tuned to each system

• Rectifies non-linear frequency response

• Adapts the system to different volumes

• Powerful, balanced sound in every situation

Unique features for premium performance

English

L.U.C.A.S PERFORMER Manual 1.0

1 L.U.C.A.S PERFORMER System

Components

Subwoofer

The L.U.C.A.S PERFORMER subwoofer’s housing is
split into two chambers. The front chamber serves
as the speaker cabinet for the 15" direct-loaded loud­speaker, which has a power-handling capacity of 500
W RMS and a nominal impedance of 8 ohms. The
active electronic circuitry, the power unit, controller
and Class D power amps are housed in a separate
compartment at the rear of the cabinet.

Satellites

Satellites are loaded with a 8" HK Audio Custom
speaker and a 1" compression driver with a 60° x 40°
CD horn. They are rated for 200 W RMS power­handling capacity and a nominal impedance of
8 ohms.

The newly developed, integrated MonoTilt ™ pole
mount allows sound energy to be utilized with great
efficiency. Troublesome ceiling reflections are
minimized; the sound is clearer, tighter, and more
focused.
Beyond that, the cabinet is stabilized at its center of
gravity - no wobbling, tilting, or unintentional
turning.

2 Transport

To transport the system, simply set the subwoofer
on its casters and place the satellites onto the sub­woofer with the foam-rubber grille side facing down.
Secure the satellites, for example, using a locking
strap. Use original HK Audio L.U.C.A.S PERFORMER
protective covers to gear up your personal system
for the rigors of the road. Amply padded and
protected against moisture, your L.U.C.A.S
PERFORMER is sure to deliver satisfying
performance for a long time to come.

More about Limiter LEDs

Dedicated LEDs, one each for the left and right
signal path as well as for the subwoofer, display the
limiter status for each of those paths.

What is this display telling me?
The green LED indicates that the input is receiving a
signal. As long as the LED lights up green, the
system is operating at low-to-medium levels, with
plenty of headroom available for the power amps.
The yellow LED may flash off and on, but it may not
illuminate continuously.

If it does this, back off the volume on your mixer.
Red indicates Protect status, that is, a malfunction
or overload has occurred and the power amps have
been muted as a precaution.

7

3 Connections and Control

Features

L.U.C.A.S PERFORMER Subwoofer

1 Limiter LEDs

Much like rev counters, these LEDs indicate the
active system’s operating status. For more info, read
the sidebar “More about Limiter LEDs.”

2 Power On LED

This LED lights up when the power switch (see rear
panel) is set to On and the system is connected to a
mains power supply.

3 Gain Left/ Right

Operation: Turn the Gain knob all the way down
(counterclockwise) before switching the system on.
Ensure the system is connected to the satellites and
all other connected components are on before
powering it up. Be sure to switch on the connected
mixer as well as all signal sources connected to it,
for example, keyboards, amps, effects, and so forth.

After you power the system up, set the Gain knob to
the 0 dBV or 12 o’clock setting. This is the preferred
level if you have connected a mixer. (Note: If you
connect a CD player or a keyboard directly to the
system, you may not be able to achieve peak volume
at this setting. If this is the case, twist the Gain knob
to the far right.)

If you hear distortion or a saturated signal, first
check the signal sources and, if possible, reduce the
output signal level there. If you are unable to turn
down the level of the signal sent to L.U.C.A.S
PERFORMER at the signal source, adjust the input
sensitivity using the Gain knobs. (see also Tips and
Tricks—section 4).

4 Subwoofer Level

Handling: When this knob is set to the 12 o’clock
position, the subwoofer’s and the satellite’s
respective volumes are matched, ensuring the
proper balance between the subwoofer’s bass output
and the stallites’ mid/high-range output. If desired,
you can twist the Subwoofer Level knob to the left,
i.e. counterclockwise, to cut the subwoofer’s level by
as much as -12 dB and to the right to boost it by as
much as 6 dB.

5 Ground

Ground lift button for separating the signal and
chassis ground in the event of hum. To rid the
system of low-frequency hum, press the Ground
switch in. If this doesn’t solve the problem, check all
power and audio cables connected to L.U.C.A.S
PERFORMER for damage, as well as all cables
routing signals to the mixing console (see also Tips
and Tricks in Section 4).

6 Input Left bzw. Input Right (Combination XLR/1/4"

jacks)
L.U.C.A.S PERFORMER is equipped with separate
left and right channel inputs for connecting to a
mixer. Connections: Connect the audio cables that
route the signal coming from your mixer (master
left/right, line out, or a similar circuit) to these
balanced inputs using microphone cables equipped
with XLR connectors. The XLR connectors’ pin
assignments must be as follows: 1= ground, 2= +,
3= -. You can also use a 1/4" Tip-Ring-Sleeve plug to
route signals via balanced circuits. Unbalanced sig­nals can be patched in via a mono plug.

7 Through Left, Trough Right

Connections: Parallel outputs for routing the line
signal (left or right) to other systems, outboard com­ponents, monitor power amps, etc., via XLR cables.

8 To Satellite Left and Right

Connections: Connect these Speakon®outputs to the
left and right L.U.C.A.S PERFORMER satellites using
speaker cables equipped with Speakon

®

connectors.
Note: Be sure to rotate the Speakon®connectors
clockwise until they lock in place!

9 Power Switch

Operation: On/off switch for the active system. The
red Power On LED in the upper control panel lights
up when the system is switched on. The active
L.U.C.A.S PERFORMER system should always be
switched on last after you power up all equipment
connected to it, and should be switched off first
before you switch off all the other equipment
connected to it.

L.U.C.A.S PERFORMER -- user panel

3 3 4

5

1 1 1 2

English

6

9

8 8

7 6 7

L.U.C.A.S PERFORMER - user panel rear

L.U.C.A.S PERFORMER Manual 1.0

10 Mains Input

Connections: Use the factory-included mains cable
(power cord) to connect from this socket to a wall
receptacle.

11 Mains Cable Tab

Clamp the power cable into the tab to prevent it
from being pulled out inadvertently.

12 Fans

These fans (on the side and back of the housing)
keep the power amp modules cool. Always keep the
fan and ventilation vents free of dirt and debris, and
ensure they remain unobstructed so air can circulate
freely.

L.U.C.A.S PERFORMER Satellite

Input

Connections: Connect the Speakon

®

inputs to the
left and right L.U.C.A.S PERFORMER satellite out­puts using speaker cables equipped with Speakon

®

connectors. Note: Be sure to twist the Speakon

®

connectors clockwise until they lock in place! You
must first disengage the safety catch before you can
unplug the connector. To do this, pull the bayonet
catch towards the cord.

4 Tips and Tricks

• Do not expose electronic circuitry to moisture!

When you set the system up outdoors, be sure to
protect it against rain. Keep soft drinks, beer or any
other liquids well away from the cabinets to protect
their electronic components from short circuits.

• To ensure proper ventilation, make sure the sub-

woofer is placed a sufficient distance away from
walls and isn’t covered by curtains and the like.
This is vital to keep the power amps cool.

• Ensure that the vents on the subwoofer’s side
panels are free of dirt and that the fan blades can
rotate freely. Otherwise, electronic components
may overheat and suffer damage.

• L.U.C.A.S PERFORMER takes care of delivering
optimum sound—so provide it with optimum
input signals! Noise such as hum is generally
caused by defective cables, the wrong type of
cables, or unbalanced signals being fed to the
mixing console. Check all audio cables and mains
cables.

• Avoid distortion! Not only is it unpleasant to your
audience’s ears, it also endangers your equipment.
Make sure all components that are connected
directly and indirectly to L.U.C.A.S PERFORMER
have sufficient power ratings, and that they are not
distorting from being driven at their respective
limits. Provide a clean, undistorted signal to the
system that won’t require backing off the Gain
knob to clean it up.

• Avoid ground loops! If, for example, you connect
the mixer to one mains circuit/wall outlet, and
L.U.C.A.S PERFORMER to another, you may
encounter a ground loop. To prevent this problem,
always connect the L.U.C.A.S PERFORMER system
and the mixing console to the same electrical
circuit (same phase!). If your equipment hums
despite this precaution, the Ground Lift switch can
be a great help.

CAUTION: Never tape over the plug’s ground
terminal – this endangers lives!

10

11

1212

L.U.C.A.S PERFORMER - user panel rear

9

5 L.U.C.A.S PERFORMER

Accessories

HK AUDIO Speaker Add On Package

This is the complete L.U.C.A.S PERFORMER
accessory kit consisting of two aluminum cabinet
tripods, one gig bag, and two speaker cables.

HK AUDIO Protective Covers for L.U.C.A.S
PERFORMER

This set comprises one cover for the subwoofer and
two covers for the satellites. Tear-resistant and
water-repellant, these rugged covers are thickly
padded to afford lasting protection for the L.U.C.A.S
PERFORMER system during transport.

To learn more about Original HK AUDIO
Accessories, talk to your HK AUDIO®dealer
or visit www.hkaudio.com.

6 Troubleshooting

The Power On LED dos not light up red after you
switch the system on.

1 Check if the power cable is plugged into the Mains

Input.

2 Check if the mains power supply is providing

current.

The Power On LED lights up, but there is no sound
coming from the cabinets.

1 Check the cables connected to the Left and Right

inputs.

2 Check if the signal sources (mixer, keyboard, CD

player) are on.
3 Is the Gain knob turned up?
4 Check the speaker cables for damage.
5 Check if the Speakon“ connectors are fully engaged

in their sockets (rotated to the right). They must
be locked in place to establish an electrical
connection.

The subwoofer’s low frequency output is too soft.

1 Check the setting of the Subwoofer Level knob.
2 Adjust this knob to set the volume of the sub-

woofer to the desired level.

Sound seems distorted.

1 Check the LED displays on your mixer. They should

not be constantly in the red. If necessary, reduce
the volume at the mixer.

2 If the LED displays on your mixer are in the green,

turn back L.U.C.A.S PERFORMER’s Gain knob.

3 Watch the LEDs of the Limit Left, Limit Right

and Limit Subwoofer displays on L.U.C.A.S
PERFORMER’s control panel. These may light up
yellow, but only intermittently. Under no
circumstances may they continuously illuminate
yellow. If this is the case, turn the Gain down
(knob counterclockwise).

Annoying hum

1 Check the cables connecting the source of the

audio signal to L.U.C.A.S PERFORMER. Replace
any damaged cords.

2 If you cannot pinpoint the cause of the humming,

press the Ground switch in. This should remedy
the problem in most cases.

English

This is to certify that

HK AUDIO

®

L.U.C.A.S PERFORMER

complies with the provisions of the Directive of
the Council of the European Communities on the
approximation of the laws of the Member States
relating to electromagnetic compatibility (EMC
Directive 89/336/EEC) and the low voltage Directive
(73/23/EEC). This declaration of conformity of the
European Communities is the result of an examination
carried out by the Quality Assurance Department
of STAMER GmbH in accordance with European
Standards EN 50081-1, EN 50082-1and EN 60065
for low voltage, as laid down in Article 10 of the
EMC Directive.

Stamer Musikanlagen
GmbH*
Magdeburger Str. 8
66606 St.Wendel

Lothar Stamer Dipl.Ing.
Managing Director
St.Wendel, 01/03/06

* Stamer Musikanlagen manufactures exclusively
for HK AUDIO

®

.

L.U.C.A.S PERFORMER Manual 1.0

Für das folgend bezeichnete Erzeugnis

HK AUDIO

®

L.U.C.A.S PERFORMER

wird hiermit bestätigt, dass es den wesentlichen
Schutzanforderungen entspricht, die in der Richtlinie
des Rates zur Angleichung der Rechtsvorschriften
der Mitgliedsstaaten über die elektromagnetische
Verträglichkeit (89/336/EWG) und der Nieder­spannungsrichtlinie (73/23/EWG) festgelegt sind.
Diese Erklärung gilt für alle Exemplare, und bestätigt
die Ergebnisse der Messungen, die durch die
Qualitätssicherung der Fa. Stamer Musikanlagen
GmbH durchgeführt wurden. Zur Beurteilung des
Erzeugnisses hinsichtlich elektromagnetischer
Verträglichkeit wurden folgende Normen herange­zogen: EN 50081-1 • EN 50082-1. Zur Beurteilung
der Einhaltung der Niederspannungsrichtlinie wurde
folgende Norm herangezogen: EN 60065

Diese Erklärung wird verantwortlich für den Hersteller

Stamer Musikanlagen
GmbH*
Magdeburger Str. 8
66606 St.Wendel

abgegeben durch

Lothar Stamer Dipl.Ing.
Geschäftsführer
St.Wendel, den 03/01/06

* Stamer Musikanlagen stellt exklusiv für
HK AUDIO®her.

11

7 Technical Specifications

L.U.C.A.S PERFORMER Subwoofer

Inputs/outputs:
Line In: XLR female, 1/4" combination jack

(pin 1= ground; 2= +, 3= -)
Input: Electronically balanced & floating
Input impedance: 47 k ohms
Sensitivity: 0 dBV (=1V)
Max. input level: + 20 dBu
Parallel out: XLR male (pin 1= ground; 2=+, 3= -)
Speaker outputs: Speakon

®

NL 4 (pin 1+= +, 1-= -)

Amplifiers:
Subwoofer output: 1x 500 W RMS / Class D power amp
Satellites output: 2x 200 W RMS / Class D power amp
Protective circuits: MultiBand limiter

Speakers:
Woofer: 1x 15"
Subwoofer frequency response: 47 Hz -130 Hz, ± 3 dB

38 Hz -130 Hz, - 10 dB

SPL 1W / 1m: 101 dB (half space)
Max. SPL / 1m: 126 dB @ 10% THD (half space)

Weights and measures:
Weight: 29,5 kg/ 64,9 lbs
Dimensions (WxHxD): 47.5 cm x 47 cm x 58.5 cm
without casters 18-3/4" x 18-1/2" x 23"

L.U.C.A.S PERFORMER Satellite

Inputs:
Speaker input: Speakon

®

NL 4 (pin 1+= +, 1-= -)

Speakers:
Woofer: 1x 8"
Driver: 1x 1"
Directivity: 60° x 40° CD horn

Overall nominal impedance: 8 ohms
Nominal power handling: 200 W RMS
SPL 1W / 1m: 102 dB (half space)
Max. SPL / 1m: 124 dB @ 10% THD (half space)
Frequency response: 130 Hz - 19 kHz, +/- 3 dB
(via Controller)
Crossover frequency (passive): 2.4 kHz/ 12 dB / octave
Driver protection: Dynamic protective circuit
Pole mount: HK Audio MonoTilt™ 36 mm, -10°

Weights and measures:
Weight: 7,2 kg/ 15,8 lbs.
Dimensions (WxHxD): 26 cm x 38,5 cm x 28,5 cm

10-1/8" x 15-1/8" x 11-1/4"

General electrical data:

Protection class 1 (protectively earthed)

Max. current consumption: 4.4 A (220 – 240 V) • 8 A (110 – 120 V)
Max. power consumption: 1000 Watts
Mains voltage range +/- 10%
Ambient temperature range
during operation: -10° C to +35° C

English