HK AUDIO ELIASPX User Manual

Manual 1.0

English
Deutsch
Français
Español

Wichtige Sicherheitshinweise!

Bitte vor Gebrauch lesen und für späteren Gebrauch
aufbewahren!

• Read all of these instructions!

• Save these instructions for later use!

•Follow all warnings and instructions marked on the product!

• Do not use this product near water, i.e. bathtub, sink, swimming pool,
wet basement, etc.

• Do not place this product on an unstable cart, stand or table. The product may
fall, causing serious damage to the product or to persons!

• Slots and openings in the cabinet and the back or bottom are provided for
ventilation; to ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered. This product should
not be placed in a built-in installation unless proper ventilation is provided.

• This product should not be placed near a source of heat such as a stove,
radiator, or another heat producing amplifier.

• Use only the supplied power supply or power cord. If you are not sure of the
type of power available, consult your dealer or local power company.

• Do not allow anything to rest on the power cord. Do not locate this product
where persons will walk on the cord.

• Never break off the ground pin on the power supply cord.

• Power supply cords should always be handled carefully. Periodically check cords
for cuts or sign of stress, especially at the plug and the point where the cord
exits the unit.

• The power supply cord should be unplugged when the unit is to be unused for
long periods of time.

• If this product is to be mounted in an equipment rack, rear support should be
provided.

• This product should be used only with a cart or stand that is recommended by
HK AUDIO

®

.

• Never push objects of any kind into this product through cabinet slots as they
may touch dangerous voltage points or short out parts that could result in risk
of fire or electric shock. Never spill liquid of any kind on the product.

• Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing
to qualified service personnel.

• Clean only with dry cloth.

• Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for the safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.

• Unplug this product from the wall outlet and refer servicing to qualified service
personnel under the following conditions:

• When the power cord or plug is damaged or frayed.

• If liquid has been spilled into the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally when the operating instructions are
followed.

• If the product has been dropped or the cabinet has been damaged.

• If the product exhibits a distinct change in performance, indicating a need of
service!

• Adjust only these controls that are covered by the operating instructions since
improper adjustment of other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to
normal operation.

• Exposure to extremely high noise levels may cause a permanent hearing loss.

• Individuals vary considerably in susceptibility to noise induced hearing loss, but
nearly everyone will lose some hearing if exposed to sufficiently intense noise
for a sufficient time. The U.S. Government´s Occupational Safety and Health
Administration (OSHA) has specified the following permissible noise level
exposures:

Duration Per Day In Hours Sound LeveldBA, Slow Response

890
692
495
397
2 100
11/2 102
1 105
1/2 110
1/4 or less 115

• According to OSHA, any exposure in excess of the above permissible limits
could result in some hearing loss.

• Ear plug protectors in the ear canals or over the ears must be worn when operating
this amplification system in order to prevent a permanent hearing loss if exposure
is in excess of the limits as set forth above. To ensure against potentially
dangerous exposure to high sound pressure levels, it is recommended that all
persons exposed to equipment capable of producing high sound pressure levels
such as this amplification system be protected by hearing protectors while this
unit is in operation.

•Fuses: Replace with IEC 127 (5x 20 mms) type and rated fuse for best
performance only.

TO PREVENT THE RISK OF FIRE AND SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO MOISTURE OR RAIN. DO NOT OPEN CASE;
NO USER SERVICE-ABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Version 1.0 10/2004

• The unit has been built by HK AUDIO

®

in accordance with IEC 60065 and left
the factory in safe working order. To maintain this condition and ensure non­risk operation, the user must follow the advice and warning comments found in
the operating instructions. The unit conforms to Protection Class 1 (protectively
earthed).

•HK AUDIO®ONLY GUARANTEE THE SAFETY, RELIABILITY AND EFFICIENCY
OF THE UNIT IF:

• Assembly, extension, re-adjustment, modifications or repairs are carried out by
HK AUDIO®or by persons authorized to do so.

• The electrical installation of the relevant area complies with the requirements
of IEC (ANSI) specifications.

• The unit is used in accordance with the operating instructions.

• The unit is regularly checked and tested for electrical safety by a competent
technician.

WARNING:

• If covers are opened or sections of casing are removed, except where this can
be done manually, live parts can become exposed.

• If it is necessary to open the unit this must be insulated from all power sources.
Please take this into account before carrying out adjustments, maintenance,
repairs and before replacing parts.

• The appliance can only be insulated from all power sources if the mains
connection is unplugged.

• Adjustment, maintenance and repairs carried out when the unit has been opened
and is still live may only be performed by specialist personnel who are authorized
by the manufacturer (in accordance with VBG 4) and who are aware of the
associated hazards.

• Loudspeaker outputs which have the IEC 417/5036 symbol (Diagram 1, below)
can carry voltages which are hazardous if they are made contact with. Before
the unit is switched on, the loudspeaker should therefore only be connected
using the lead recommended by the manufacturer.

• Where possible, all plugs on connection cables must be screwed or locked onto
the casing.

• Replace fuses only with IEC127 type and specified ratings.

• It is not permitted to use repaired fuses or to short-circuit the fuse holder.

• Never interrupt the protective conductor connection.

• Surfaces which are equipped with the "HOT" mark (Diagram 2, below), rear
panels or covers with cooling slits, cooling bodies and their covers, as well as
tubes and their covers are purposely designed to dissipate high temperatures
and should therefore not be touched.

• High loudspeaker levels can cause permanent hearing damage. You should
therefore avoid the direct vicinity of loudspeakers operating at high levels.
Wear hearing protection if continuously exposed to high levels.

MAINS CONNECTION:

• The unit is designed for continuous operation.

• The set operating voltage must match the local mains supply voltage.

• The unit is connected to the mains via the supplied power unit or power cable.

• Power unit: Never use a damaged connection lead. Any damage must be rectified
by a competent technician.

•Avoid connection to the mains supply in distributor boxes together with several
other power consumers.

• The plug socket for the power supply must be positioned near the unit and
must be easily accessible.

PLACE OF INSTALLATION:

• The unit should stand only on a clean, horizontal working surface.

• The unit must not be exposed to vibrations during operation.

• Keep away from moisture and dust where possible.

• Do not place the unit near water, baths, wash basins, kitchen sinks, wet areas,
swimming pools or damp rooms. Do not place objects containing liquid on the
unit - vases, glasses, bottles etc.

• Ensure that the unit is well ventilated.

• Any ventilation openings must never be blocked or covered. The unit must be
positioned at least 20 cm away from walls. The unit may only be fitted in a rack
if adequate ventilation is ensured and if the manufacturer's installation instruc­tions are followed.

• Keep away from direct sunlight and the immediate vicinity of heating elements
and radiant heaters or similar devices.

• If the unit is suddenly moved from a cold to a warm location, condensation can
form inside it. This must be taken into account particularly in the case of tube
units. Before switching on, wait until the unit has reached room temperature.

• Accessories: Do not place the unit on an unsteady trolley, stand, tripod, base or
table. If the unit falls down, it can cause personal injury and itself become damaged.
Use the unit only with the trolley, rack stand, tripod or base recommended by
the manufacturer or purchased together with the unit. When setting the unit
up, all the manufacturer's instructions must be followed and the setup accessories
recommended by the manufacturer must be used. Any combination of unit and
stand must be moved carefully. A sudden stop, excessive use of force and uneven
floors can cause the combination of unit and stand to tip over.

• Additional equipment: Never use additional equipment which has not been
recommended by the manufacturer as this can cause accidents.

•To protect the unit during bad weather or when left unattended for prolonged
periods, the mains plug should be disconnected. This prevents the unit being
damaged by lightning and power surges in the AC mains supply.

Diagram 1 Diagram 2

•Das Gerät wurde von HK AUDIO®gemäß IEC 60065 gebaut und hat das Werk
in sicherheitstechnisch einwandfreiem Zustand verlassen. Um diesen Zustand
zu erhalten und einen gefahrlosen Betrieb sicherzustellen, muss der Anwender
die Hinweise und die Warnvermerke beachten, die in der Bedienungsanleitung
enthalten sind. Das Gerät entspricht der Schutzklasse I (schutzgeerdet).

• DIE SICHERHEIT, ZUVERLÄSSIGKEIT UND LEISTUNG DES GERÄTES WIRD
VON HK AUDIO®NUR DANN GEWÄHRLEISTET, WENN:

• Montage, Erweiterung, Neueinstellung, Änderungen oder Reparaturen von
HK AUDIO®oder von dazu ermächtigten Personen ausgeführt werden.

• die elektrische Installation des betreffenden Raumes den Anforderungen von
IEC (ANSI)-Festlegungen entspricht.

• das Gerät in Übereinstimmung mit der Gebrauchsanweisung verwendet wird.

WARNUNG:

•Wenn Abdeckungen geöffnet oder Gehäuseteile entfernt werden, außer wenn
dies von Hand möglich ist, können Teile freigelegt werden, die Spannung führen.

•Wenn ein Öffnen des Gerätes erforderlich ist, muss das Gerät von allen Span­nungsquellen getrennt sein. Berücksichtigen Sie dies vor dem Abgleich, vor
einer Wartung, vor einer Instandsetzung und vor einem Austausch von Teilen.

• Ein Abgleich, eine Wartung oder eine Reparatur am geöffneten Gerät unter
Spannung darf nur durch eine vom Hersteller autorisierte Fachkraft (nach VBG

4) geschehen, die mit den verbundenen Gefahren vertraut ist.

• Lautsprecher-Ausgänge, die mit dem IEC 417/5036-Zeichen (Abb.1, s.unten)
versehen sind können berührungsgefährliche Spannungen führen. Deshalb vor
dem Einschalten des Gerätes Verbindung nur mit dem vom Hersteller empfoh­lenen Anschlusskabel zum Lautsprecher herstellen.

• Alle Stecker an Verbindungskabeln müssen mit dem Gehäuse verschraubt oder
verriegelt sein, sofern möglich.

• Es dürfen nur Sicherungen vom Typ IEC 127 und der angegebenen Nennstrom­stärke verwendet werden.

• Eine Verwendung von geflickten Sicherungen oder Kurzschließen des Halters ist
unzulässig.

• Niemals die Schutzleiterverbindung unterbrechen.

• Oberflächen, die mit dem "HOT"-Zeichen (Abb.2, s.unten) versehen sind, Rück­wände oder Abdeckungen mit Kühlschlitzen, Kühlkörper und deren Abdeckun­gen, sowie Röhren und deren Abdeckungen können im Betrieb erhöhte Tempe­raturen annehmen und sollten deshalb nicht berührt werden.

• Hohe Lautstärkepegel können dauernde Gehörschäden verursachen.
Vermeiden Sie deshalb die direkte Nähe von Lautsprechern, die mit hohen
Pegeln betrieben werden. Verwenden Sie einen Gehörschutz bei dauernder
Einwirkung hoher Pegel.

NETZANSCHLUSS:

• Das Gerät ist für Dauerbetrieb ausgelegt.

• Die eingestellte Betriebsspannung muss mit der örtlichen Netzspannung
übereinstimmen.

• Der Anschluss an das Stromnetz erfolgt mit dem mitgelieferten Netzteil oder
Netzkabel.

• Netzteil: Eine beschädigte Anschlussleitung kann nicht ersetzt werden.
Das Netzteil darf nicht mehr betrieben werden.

•Vermeiden Sie einen Anschluss an das Stromnetz in Verteilerdosen zusammen
mit vielen anderen Stromverbrauchern.

• Die Steckdose für die Stromversorgung muss nahe am Gerät angebracht und
leicht zugänglich sein.

AUFSTELLUNGSORT:

• Das Gerät sollte nur auf einer sauberen, waagerechten Arbeitsfläche stehen.

• Das Gerät darf während des Betriebs keinen Erschütterungen ausgesetzt sein.

•Feuchtigkeit und Staub sind nach Möglichkeit fernzuhalten.

• Das Gerät darf nicht in der Nähe von Wasser, Badewanne, Waschbecken,
Küchenspüle, Nassraum, Swimmingpool oder feuchten Räumen betrieben
werden. Keine mit Flüssigkeit gefüllten Gegenstände -Vase, Gläser, Flaschen
etc. auf das Gerät stellen.

• Sorgen Sie für ausreichende Belüftung der Geräte.

•Eventuelle Ventilationsöffnungen dürfen niemals blockiert oder abgedeckt
werden. Das Gerät muß mindestens 20 cm von Wänden entfernt aufgestellt
werden. Das Gerät darf nur dann in ein Rack eingebaut werden, wenn für
ausreichende Ventilation gesorgt ist und die Einbauanweisungen des Her­stellers eingehalten werden.

•Vermeiden Sie direkte Sonneneinstrahlung sowie die unmittelbare Nähe von
Heizkörpern und Heizstrahlern oder ähnlicher Geräte.

•Wenn das Gerät plötzlich von einem kalten an einen warmen Ort gebracht wird,
kann sich im Geräteinnern Kondensfeuchtigkeit bilden. Dies ist insbesondere
bei Röhrengeräten zu beachten. Vor dem Einschalten solange warten bis das
Gerät Raumtemperatur angenommen hat.

• Zubehör: Das Gerät nicht auf einen instabilen Wagen, Ständer, Dreifuß, Unter­satz oder Tisch stellen. Wenn das Gerät herunterfällt, kann es Personenschäden
verursachen und selbst beschädigt werden. Verwenden Sie das Gerät nur mit
einem vom Hersteller empfohlenen oder zusammen mit dem Gerät verkauften
Wagen, Rack, Ständer, Dreifuß oder Untersatz. Bei der Aufstellung des Gerätes
müssen die Anweisungen des Herstellers befolgt und muss das vom Hersteller
empfohlene Aufstellzubehör verwendet werden. Eine Kombination aus Gerät
und Gestell muss vorsichtigt bewegt werden. Plötzliches Anhalten, übermäßige
Kraftanwendung und ungleichmäßige Böden können das Umkippen der Kombi­nation aus Gerät und Gestell bewirken.

• Zusatzvorrichtungen: Verwenden Sie niemals Zusatzvorrichtungen, die nicht
vom Hersteller empfohlen wurden, weil dadurch Unfälle verursacht werden
können

• Zum Schutz des Gerätes bei Gewitter oder wenn es längere Zeit nicht beauf­sichtigt oder benutzt wird, sollte der Netzstecker gezogen werden.
Dies verhindert Schäden am Gerät aufgrund von Blitzschlag und Spannungs­stößen im Wechselstromnetz.

Abb.1 Abb.2

Important Safety Instructions

Before connecting, read instructions

Important Advice on Safety!

Please read before use and keep for later use!

• L'appareil a été conçu par HK AUDIO®selon la norme IEC 60065 et a quitté
l'entreprise dans un état irréprochable. Afin de conserver cet état et d'assurer
un fonctionnement sans danger de l'appareil nous conseillons à l'utilisateur la
lecture des indications de sécurité contenues dans le mode d'emploi. L'appareil
est conforme à la classification I (mise à terre de protection).

• SURETE, FIABILITE ET EFFICACITE DE L'APPAREIL NE SONT GARANTIS PAR
HK AUDIO®QUE SI:

• Montage, extension, nouveau réglage, modification ou réparation sont
effectués par HK AUDIO®ou par toute personne autorisée par HK AUDIO®.

• L'installation électrique de la pièce concernée correspond aux normes
IEC (ANSI).

• L'utilisation de l'appareil suit le mode d'emploi.

AVERTISSEMENT:

•A moins que cela ne soit manuellement possible, tout enlèvement ou ouverture
du boîtier peut entrainer la mise au jour de pieces sous tension.

• Si l'ouverture de l'appareil est nécessaire, celui-ci doit être coupé de chaque
source de courant. Ceci est à prendre en considération avant tout ajustement,
entretien, réparation ou changement de pieces.

• Ajustement, entretien ou réparation sur l'appareil ouvert et sous tension ne
peuvent être éffectués que par un spécialiste autorisé par le fabricant (selon
VBG4). Le spécialiste étant conscient des dangers liés à ce genre de réparation.

• Les sorties de baffles qui portent le signe IEC 417/5036 (fig. 1, voir en bas)
peuvent être sous tension dangereuse. Avant de brancher l'appareil utiliser
uniquement le câble de raccordement conseillé par le fabricant pour raccorder
les baffles.

•Toutes les prises des câbles de raccordement doivent être, si possible, vissées
ou verrouillées sur le boîtier.

•L’utilisation de fusibles rafistolés ou court-circuites est inadmissible –
seulement: IEC127.

• L'utilisation de fusibles rafistolés ou court-circuites est inadmissible.

• Ne jamais interrompre la connexion du circuit protecteur.

• Il est conseillé de ne pas toucher aux surfaces pourvues du signe "HOT" (fig. 2,
voir en bas), aux parois arrières ou caches munis de fentes d'aération,
éléments d'aération et leurs caches ansi qu'aux tubes et leurs caches.
Ces éléments pouvant atteindre des températures élévées pendant l'utilisation
de l'appareil.

• Les Niveaux de puissance élévés peuvent entrainer des lésions auditives
durables. Evitez donc la proximité de haut-parleurs utilisés à haute puissance.
Lors de haute puissance continue utilisez une protection auditive.

BRANCHEMENT SUR LE SECTEUR:

• L'appareil est conçu pour une utilisation continue.

• La tension de fonctionnement doit concorder avec la tension secteur locale.

• Le raccordement au réseau éléctrique s'effectue avec l'adaptateur ou le cordon
d´alimentation livré avec l'appareil.

• Adaptateur: Un câble de raccordement abimé ne peut être remplacé. L'adapta­teur est inutilisable.

•Evitez un raccordement au réseau par des boîtes de distribution surchargées.

• La prise de courant doit être placée à proximité de l'appareil et facile à atteindre.

LIEU D'INSTALLATION:

• L'appareil doit être placé sur une surface de travail propre et horizontale.

• L'appareil en marche ne doit en aucun cas subir des vibrations.

•Evitez dans la mesure du possible poussière et humidité.

• L'appareil ne doit pas être placé à proximité d'eau, de baignoire, lavabo, évier,
pièce d'eau, piscine ou dans une pièce humide. Ne placez aucun vase, verre,
bouteille ou tout objet rempli de liquide sur l'appareil.

• L'appareil doit être suffisamment aéré.

• Ne jamais recouvrir les ouvertures d'aération. L'appareil doit être placé à 20 cm
du mur au minimum. L'appareil peut être monté dans un Rack si une
ventilation suffisante est possible et si les conseils de montage du fabricant
sont suivis.

•Evitez les rayons de soleil et la proximité de radiateurs, chauffages etc.

• Une condensation d'eau peut se former dans l'appareil si celui-ci est transporté
brusquement d'un endroit froid à un endroit chaud. Ceci est particulièrement
important pour des appareils à tubes. Avant de brancher l'appareil attendre
qu'il ait la température ambiante.

• Accessoires: L'appareil ne doit être placé sur un chariot, support, trépied, bâti
ou table instable. Une chute de l'appareil peut entrainer aussi bien des domma­ges corporels que techniques. Utilisez l'appareil uniquement avec un chariot,
Rack, support, trépied ou bâti conseillé par le fabricant ou vendu en combinai­son avec l'appareil. Les indications du fabricant pour l'installation de l'appareil
sont à suivre, et les accessoires d'installation conseillés par le fabricant sont à
utiliser. Un ensemble support et appareil doit être déplacé avec précaution.
Des mouvements brusques et des revêtements de sol irreguliers peuvent
entrainer la chute de l´ensemble.

• Equipements supplémentaires: Ne jamais utiliser un équipement supplémen­taire n'ayant pas été conseillé par le fabricant, ceci pouvant entrainer des
accidents.

•Afin de protéger l'appareil pendant un orage ou s'il ne doit pas être utilisé
pendant un certain temps, il est conseillé d'enlever la prise au secteur.
Ceci évite des dommages dûs à la foudre ou à des coups de tension dans le
réseau à courant alternatif.

Fig. 1 Fig. 2

• L'apparecchio è stato costruito dalla HK AUDIO®secondo la normativa euro­pea IEC 60065 ed ha lasciato il nostro stabilimento in stato ineccepibile. Per
garantire il mantenimento di tale stato e un utilizzo assolutamente privo di ri­schi l'utente è tenuto ad osservare le indicazioni e gli avvertimenti di sicurezza
contenuti nelle istruzioni per l'uso. L'apparecchio rispecchia il livello di
sicurezza I (collegato a terra).

•Sicurezza, affidabilità e prestazioni dell'apparecchio vengono garantiti dalla
HK AUDIO®solo ed esclusivamente se:

•Montaggio, ampliamento, rimessa a punto, modifiche e riparazioni vengono
eseguite dalla HK AUDIO®stessa o da personale da essa autorizzato.

• Gli impianti elettrici nei locali prescelti per l'uso dell'apparecchio rispondono
alle normative stabilite dall'ANSI.

• L'apparecchio viene utilizzato come indicato nel libretto delle istruzioni per l'uso.

Avvertimenti:

• In caso di apertura di parti di rivestimento o rimozione di parti dell'involucro,
a meno che non si tratti di pezzi rimovibili semplicemente a mano, possono
venire alla luce parti dell'apparecchio conduttrici di tensione.

• Se l'apertura dell'apparecchio dovesse risultare necessaria è indispensabile
staccare precedentemente quest'ultimo da tutte le fonti di tensione. Rispettare
tale misura di prevenzione anche prima di un allineamento, di operazioni di
manutenzione, della messa in esercizio o della sostituzione di componenti
all'interno dell'apparecchio.

• Allineamento, operazioni di manutenzione o eventuali riparazioni dell'appa­recchio in presenza di tensione vanno eseguite esclusivamente da personale
specializzato ed autorizzato, in grado di eseguire tali operazioni evitandone
i rischi connessi.

• Le uscite degli altoparlanti contrassegnate dai caratteri IEC 417/5036 (vedi
illustrazione 1 a fondo pag.) possono essere conduttrici di tensione pericolosa
con cui evitare il contatto. Per questo motivo, prima di accendere l'appa­recchio, collegare quest'ultimo agli altoparlanti servendosi esclusivamente del
cavetto d'allacciamento indicato dal produttore.

•Tutte le spine e i cavi di collegamento devono essere avvitati o fissati all'invo­lucro dell'apparecchio per quanto possibile.

• Utilizzare esclusivamente fusibili del tipo IEC 127 con la indicata corrente no­minale.

• L'utilizzo di fusibili di sicurezza non integri e la messa in corto circuito del
sostegno di metallo sono proibite.

• Non interrompere mai il collegamento con il circuito di protezione.

• Superfici contrassegnate dalla parola "HOT" (vedi illustrazione 2 a fondo pag.),
cosi come griglie di aerazione, dispositivi di raffreddamento e i loro rivestimen­ti di protezione, oppure valvole e i relativi rivestimenti protettivi possono surri­scaldarsi notevolmente durante l'uso e per questo motivo non vanno toccate.

• L'ascolto di suoni ad alto volume può provocare danni permanenti all'udito.
Evitate perciò la diretta vicinanza con altoparlanti ad alta emissione di suono
e utilizzate cuffie protettive in caso ciò non sia possibile.

Alimentazione:

• L'apparecchio è concepito per il funzionamento continuo.

• La tensione di esercizio deve corrispondere alla tensione di rete a cui ci si allaccia.

• L'allacciamento alla rete elettrica avviene tramite alimentatore o cavetto d'ali­mentazione consegnato insieme all'apparecchio.

• Alimentatore: un cavo di connessione danneggiato non può essere sostituito.
L'alimentatore non può più essere utilizzato.

•Evitate un allacciamento alla rete di corrente utilizzando cassette di distribu­zione sovraccariche.

• La spina di corrente deve essere situata nelle vicinanze dell'apparecchio e
facilmente raggiungibile in qualsiasi momento.

Locali di collocamento:

• Opportuno collocare l'apparecchio su una superficie pulita e orizzontale.

• Non sottoporre l'apparecchio in funzione a scosse e vibrazioni.

• Proteggere l'apparecchio per quanto possibile da umidità e polvere.

• Non collocare l'apparecchio vicino ad acqua, vasche da bagno, lavandini, lavelli
da cucina, locali umidi o piscine. Non appoggiare recipienti contenenti liquidi ­vasi, bicchieri, bottiglie, ecc. - sull'apparecchio.

• Provvedere ad una buone aerazione dell'apparecchio.

•Eventuali aperture previste per la ventilazione dell'apparecchio non vanno ne
bloccate, ne mai coperte. L'apparecchio va collocato ad almeno 20 cm di di­stanza dalle pareti circostanti e può essere inserito tra altre componenti di un
impianto solo in caso di sufficiente ventilazione e qualora le direttive di
montaggio del produttore vengano rispettate.

•Evitare di esporre l'apparecchio ai raggi del sole e di collocarlo direttamente
nelle vicinanze di fonti di calore come caloriferi, stufette, ecc.

• Se l'apparecchio viene trasportato rapidamente da un locale freddo ad uno
riscaldato può succedere che al suo interno si crei della condensa. Ciò va
tenuto in considerazione soprattutto in caso di apparecchi a valvole. Attendere
che l'apparecchio abbia assunto la temperatura ambiente prima di accenderlo.

• Accessori: non collocare l'apparecchio su carrelli, supporti, treppiedi, superfici
o tavoli instabili. Se l'apparecchio dovesse cadere a terra potrebbe causare
danni a terzi o danneggiarsi irreparabilmente. Utilizzate per il collocamento
dell'apparecchio supporti, treppiedi e superfici che siano consigliate dal
produttore o direttamente comprese nell'offerta di vendita. Per il collocamento
dell'apparecchio attenetevi strettamente alle istruzioni del produttore, utili­zzando esclusivamente accessori da esso consigliati. L'apparecchio in combina­zione ad un supporto va spostato con molta attenzione. Movimenti bruschi o il
collocamento su pavimenti non piani possono provocare la caduta dell'appa­recchio e del suo supporto.

• Accessori supplementari: non utilizzate mai accessori supplementari che non
siano consigliati dal produttore, potendo essere ciò causa di incidenti.

• Per proteggere l'apparecchio in caso di temporali o nel caso questo non venisse
utilizzato per diverso tempo si consiglia di staccarne la spina di corrente.
In questo modo si evitano danni all'apparecchio dovuti a colpi di fulmine o ad
improvvisi aumenti di tensione nel circuito di corrente alternata.

Illustrazione 1 Illustrazione 2

• El aparato ha sido producido por HK AUDIO®según el IEC 60065 y salió de la
fábrica en un estado técnicamente perfecto. Para conservar este estado y
asegurar un funcionamiento sin peligros el usuario debe tener en cuenta las
indicaciones y advertencias contenidas en las instrucciones de manejo.
El aparato corresponde a la clase de protección l (toma de tierra protegida).

• LA SEGURIDAD, LA FIABILIDAD Y EL RENDIMIENTO DEL APARATO SOLO
ESTAN GARANTIZADOS POR HK AUDIO®CUANDO:

• el montaje, la ampliación, el reajuste, los cambios o las reparaciones se
realicen por HK AUDIO®o por personas autorizadas para HK AUDIO®;

• la instalación eléctrica del recinto en cuestión corresponda a los requisitos
de la determinación del IEC (ANSI);

• el aparato se use de acuerdo con las indicaciones de uso.

ADVERTENCIA:

• Si se destapan protecciones o se retiran piezas de la carcasa, exceptuando si se
puede hacer manualmente, se pueden dejar piezas al descubierto que sean
conductoras de tensión.

• Si es necesario abrir el aparato, éste tiene que estar aislado de todas las
fuentes de alimentación. Esto se debe tener en cuenta antes del ajuste, de un
entretenimiento, de una reparación y de una sustitución de las piezas.

• Un ajuste, un entretenimiento o una reparación en el aparato abierto y bajo
tensión sólo puede ser llevado a cabo por un especialista autorizado por el
productor (según VBG 4) que conozca a fondo los peligros que ello conlleva.

• Las salidas de altavoces que estén provistas de la característica IEC 417/5036
(figura 1, véase abajo) pueden conducir tensiones peligrosas al contacto. Por
ello es indispensable que antes de poner en marcha el aparato; la conexión se
haya realizado únicamente con el cable de empalmes recomendado por el
productor.

• Las clavijas de contacto al final de los cables conectores tienen que estar
atornilladas o enclavadas a la carcasa, en tanto que sea posible.

• Sólo se pueden utilizar fusibles del tipo IEC 127 con la intensidad de corriente
nominal indicada.

• El uso de fusibles reparados o la puesta en cortocircuito del soporte es
inadmisible.

• El empalme del conductor de protección no se puede interrumpir en ningún
caso.

• Las superficies provistas de la característica "HOT" (figura 2, véase abajo),
los paneles de fondo trasero o las protecciones con ranuras de ventilación, los
cuerpos de ventilación y sus protecciones, así como las válvulas electrónicas y
sus protecciones pueden alcanzar temperaturas muy altas durante el funcio­namiento y por ello no se deberían tocar.

• Niveles elevados de la intensidad de sonido pueden causar continuos daños
auditivos; por ello debe evitar acercarse demasiado a altavoces que funcionen
a altos niveles. En tales casos utilice protecciones auditivas.

ACOMETIDA A LA RED:

• El aparato está proyectado para un funcionamiento continuo.

• La tensión de funcionamiento ajustada tiene que coincidir con la tensión de la
red del lugar.

• La conexión a la red eléctrica se efectuará con la fuente de alimentación o con
el cable de red que se entreguen con el aparato.

•Fuente de alimentación: una linea de conexión dañada no se puede sustituir.
La fuente de alimentación no puede volver a ponerse en funcionamiento.

•Evite una conexión de la red eléctrica a distribuidores con muchas tomas de
corriente.

• El enchufe para el suministro de corriente tiene que estar cerca del aparato
y ser de fácil acceso.

SITUACION:

• El aparato debería estar situado en una superficie limpia y totalmente horizontal.

• El aparato no puede estar expuesto a ningún tipo de sacudidas durante su
funcionamiento.

• Se deben evitar la humedad y el polvo.

• El aparato no puede ponerse en funcionamiento cerca del agua, la bañera, el
lavamanos, la pila de la cocina, un recinto con tuberías de agua, la piscina o en
habitaciones húmedas. Tampoco se pueden poner objetos llenos de líquido ­jarrones, vasos, botellas, etc. - encima de él.

• Procure que el aparato tenga suficiente ventilación.

• Las aberturas de ventilación existentes no se deben bloquear ni tapar nunca.
El aparato debe estar situado como mínimo a 20 cm de la pared. El aparato
sólo se puede montar en un rack, si se ha procurado la suficiente ventilación y
se han cumplido las indicaciones de montaje del productor.

•Evite los rayos del sol directos así como la proximidad a radiadores, electro­radiadores o aparatos similares.

• Si el aparato pasa repentinamente de un lugar frío a otro caliente, se puede
condensar humedad en su interior. Esto se debe tener en cuenta sobretodo en
los aparatos con válvulas electrónicas. Antes de poner en marcha el aparato se
debe esperar hasta que éste haya adquirido la temperatura ambiental.

• Accesorios: el aparato no se puede colocar encima de carros, estantes, trípodes,
soportes o mesas inestables. Si el aparato se cae puede causar daños perso­nales y se puede estropear. Coloque el aparato sólo en un carro, rack, estante,
trípode o soporte recomendado por el productor o que se le haya vendido junto
con el aparato. En la instalación se deben seguir las indicaciones del productor
así como utilizar los accesorios recomendados por el mismo para colocarlo
encima. El conjunto del aparato con el pedestal se debe mover con mucho
cuidado. Un paro brusco, la aplicación de una fuerza desmesurada o un suelo
irregular puede ocasionar la caida de todo el conjunto.

• Piezas adicionales: no utilice nunca piezas adicionales que no estén recomen­dadas por el productor, ya que se podrían provocar accidentes.

• Para protejer el aparato de una tormenta o si no se supervisa ni utiliza durante
algún tiempo, se debería desconectar la clavija de la red. Así se evitan daños en
el aparato a causa de un rayo y golpes de tensión en la red de corriente alterna.

Figura 1 Figura 2

Conseils de Securite Importants!

Priere de lire avant l'emploi et a conserver pour uti­lisation ulterieure!

Importanti avvertimenti di sicurezza!

Leggere attentamente prima dell'uso e conservare per
un utilizzo successivo:

¡Indicaciones de seguridad importantes!

¡Léanse antes de utilizar el aparato y guardense para
so uso posterior!

ELIAS PX Manual 1.0

Welcome to the HK AUDIO
family!

Thank you for choosing an HK AUDIO®product.

With ELIAS PX, you now have at your disposal a two­way active PA system that combines state-of-the-art
technology with very easy operation, as well as a
professional tool for mastering demanding sound
reinforcement challenges. The system comprises two
EPX 112 A cabinets for rendering mid/high-range
frequencies and two EPX 115 A Sub subwoofers for
low-range frequencies. All the circuitry required to
operate each enclosure is integrated in that same
enclosure. Power amps, crossovers, controller
circuitry, limiters and the bottom-end–response
enhancing Dynaclip™ circuitry combine in each loud­speaker cabinet to form a self-contained, cohesive
unit. No more lengthy cables, no more passive
components. What’s more, the circuitry is matched
precisely to each cabinet’s speakers. All this adds up
to make ELIAS PX a better performing and better
sounding system that offers enhanced pulse
response and maximum protection against overload.

Our engineers developed new technologies to satisfy
the stringent requirements of such an advanced
system. With its unique and sophisticated features
every active HK AUDIO sound reinforcement system
stands out from the rest of the crowd.

All the best from the HK AUDIO team; enjoy your
ELIAS PX!

Warranty

Register your ELIAS PX using the enclosed warranty
card to extend your warranty to five years free of
charge! Use the convenient online registration
option at www

.hkaudio.com.
If you are unable to register online, please fill out the
enclosed warranty card completely and mail or fax it
to us. The registration is only valid if the warranty
registration card is filled out and returned to
HK AUDIO®or the device is registered via the
Internet within 30 days of the date of purchase.
We are also interested in learning where our
products are used and by whom. This information
will help us design future products. Your personal
information is of course protected by privacy laws.

Thank you!

HK AUDIO

®

Technical Service
Postfach 1509
D-66959 St. Wendel
Germany

Table of Contents

1 ELIAS PX System Components . . . . . . . . . . . . . .6

2Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

3 Setup and Cable Connections . . . . . . . . . . . . . . .6

4Connections and Control Features . . . . . . . . . . .8

5 Tips and Tricks . . . . . . . . . . . . . . . . . . . . . . . . . .8

6 ELIAS PX Accessories . . . . . . . . . . . . . . . . . . . . .9

7Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . .9

8Technical Specifications . . . . . . . . . . . . . . . . . . .10

5

English

Unique features for premium performance

Opto-Limiter

for the mid/high-range

Mid/high-range signals and low frequencies must be
processed in different ways. This is why ELIAS PX is
equipped with an Opto-limiter based on technology
initially developed for high-end recording gear. Its
soft-knee attack sounds more pleasant and incon­spicuous. The signal’s original envelope remains
virtually intact, ensuring far more natural-sounding
dynamic response.

• Ultra-low distortion for enhanced signal quality

• Soft-knee attack for far more harmonious and
unobtrusive limiting

• The initial waveform remains uncorrupted for
natural-sounding dynamic response

DynaClip™ Limiter

for the bass power amp

HK AUDIO’s DynaClip™ technology was developed
specifically for enhancing low-end performance. The
DynaClip™ Limiter compensates for the subwoofer’s
slower initial transient response and audibly
improves pulse behavior. This makes the most of
low-frequency energy, and enhanced efficiency
translates to more power.

• More efficient use of energy for more powerful low­end punch

• Compensates for transient response of speaker
diaphragms for improved pulse behavior

• Fine-tuned for peak bass power amp performance

OFR™

Optimized Frequency Response Technology

A new technology unique to HK AUDIO, OFR™ helps
this system deliver assertive yet well-balanced sound
at every volume level. OFR™ corrects for the non­linear frequency response inherent in the speaker
components and adapts the system’s sound output
to comply with the way the human ear hears at
different levels.

• Fine-tuned to each system

• Compensates for non-linear frequency response

• Adapts the system to differing volume levels

• Powerful, balanced sound in every situation

1" driver

for natural-sounding response

ELIAS PX mid/high units feature a professional-grade
1" driver engineered to deliver low-distortion
performance even at threshold levels and conjure
a natural-sounding sonic image. In combination with
a 60° x 40° horn, it provides the focused directivity
required to satisfy real-world sound reinforcement
demands.

DuoTilt™

– making the most of sonic energy

The novel DuoTilt™ pole mount enables sound
energy to be utilized more efficiently. It offers two
angles of tilt (7.5° and 15°), allowing satellites to be
aligned perfectly toward the audience. Troublesome
ceiling reflections are minimized; the sonic image
becomes clearer, tighter, and more focused.

Easy Setup and Handling

– less pre-gig stress

Like all HK AUDIO Active Systems, ELIAS PX was
designed as a cohesive unit consisting of perfectly
matched components. Painstaking effort was
invested to ensure ELIAS PX can be transported
easily and set up quickly. Handling and EQing
couldn’t be any easier.

ELIAS PX Manual 1.0

1 ELIAS PX System Components

EPX 112 A Mid/High Unit

These enclosures are loaded with one 12" HK AUDIO
Custom speaker and one 1" compression driver with
a 60° x 40° CD horn. Delivering 400 W RMS, the
power amp and other electronic circuitry are housed
in a separate chamber.

The novel integrated HK AUDIO DuoTilt™ pole
mount allows sound energy to be utilized far more
efficiently. Troublesome ceiling reflections are
minimized, enhancing punch and clarity. The cabinet
is stabilized at its center of gravity - no wobbling or
unintentional tilting or turning.

EPX 115 Sub A Subwoofer

The ELIAS PX subwoofer’s housing is split into two
chambers. The front chamber serves as the speaker
cabinet for the 15” direct-loaded woofer with 400­watt RMS power-handling capacity and 8-ohm
nominal impedance. The power amp and other
circuitry are housed in a separate compartment
at the rear of the cabinet.

2 Transport

To transport the system, simply set the subwoofers
on their casters and place the mid/high units onto
the subwoofers with the foam rubber grille side
facing down. Use original HK AUDIO‚ covers to get
your system ready to handle the rigors of the road.
Padded and protected against moisture, your ELIAS
PX system is sure to serve you well for a long time to
come.

3 Setup and Cable Connections

3.1 Aligning Speakers with DuoTilt™

The new, integral DuoTilt™ pole mount enables
sound energy to be used far more efficiently.
Offering two different angles of 7.5° and 15°, it lets
you angle the speakers directly at the audience.
DuoTilt™ stabilizes the cabinet at its center of
gravity with no wobbling or unintentional tilting or
turning.

Your choice of DuoTilt™ angle 7.5° or 15° depends on
the required speaker height and the size of the room.
The front opening of the HK Audio DuoTilt™ inclines
the cabinet 7.5°, and the rear opening 15°.

If you set mid/high units on fully extended tripods or
mounting poles, select 15° to minimize ceiling
reflections.

If you want to address an audience where the
majority of listeners are farther from the speakers,
opt for 7.5°.

ELIAS EPX 112 A

ELIAS EPX 115 Sub A

7.5° and 15° angles of tilt

7

English

3.2 ELIAS PX Standard Setup

The Standard Setup comprises two ELIAS
EPX A 112 mid/high units and two ELIAS EPX
115 A Sub subwoofers.

With the benefit of the ELIAS PX system’s integrated
design, it takes but a few minutes to connect cables.
Before you get started, make sure the mains switch
is set to the OFF position.
Connect cords carrying signals from your mixer
(master left/right, line out, or similar circuit) to the
balanced input socket of any component. It doesn’t
matter which component you connect first—sub­woofer or mid/high unit. Using a standard XLR
microphone cord, patch the signal from this first
component’s Through output jack to the next
component’s Input. Connect all subsequent
components in the same manner.
Yo u can vary the number of the components freely
without having to cope with compatibility, frequency
separation or impedance problems, which lets you
flexibly adapt the ELIAS PX system to your needs.

Connect the power cable only after you have made
sure that the local mains voltage matches the
voltage specified on the device. Connecting to the
wrong mains voltage may destroy ELIAS PX’s
electronic components.

The metal cleat below the Mains socket prevents the
power cord from being pulled out accidentally. Feed
the power cable through this mains cord cleat to
assure the cable is relieved of undue tension.

3.2 ELIAS PX Fullrange Setup

The full-range setup comprises two ELIAS
EPX 112 A mid/high units.

When operating mid/high units without subwoofers,
please set the mode switch to Full-range so that the
entire frequency range including low frequencies is
rendered.

3.3 ELIAS PX Extension Setup

The extension setup comprises two ELIAS
EPX 112 A mid/high units and four ELIAS EPX
115 Sub A subwoofers.

The procedure for setting up components and
connecting cords is the same as for a standard ELIAS
PX system, with the addition of two more
subwoofers.

3.4 Using the Tilt Unit to Align an Extension

Setup’s Mid/High Units

Mounting the optional tilt unit couldn’t be easier:
Proceed as if mounting the enclosure on a pole. Set
the tilt unit with the bottom plate facing down atop
the upper subwoofer, and then set the ELIAS PX
mid/high unit on it in such a way that the tilt unit’s
rod is inserted into one of the two holes (7.5° or 15°).

Tilt unit in action

Question

Can I connect speakers other than an ELIAS PX Sub
A subwoofer to an ELIAS PX mid/high unit?

Answer

The system components are acoustically matched
for optimum audio performance and may be
operated in the indicated configuration only.
Using other subwoofers can degrade the sound.

Standard system connections

Full-range setup connections

Extension setup connections

ELIAS PX Manual 1.0

4 Connections and Control

Features

ELIAS EPX 112 A

1 Mode Switch

Operation: This switch configures the ELIAS PX
mid/high unit for use in full-range mode (without
subwoofers) or for use as a satellite in combination
with the subwoofer.

2 Ground

Ground Lift button for separating the signal and
chassis ground if humming noises occur. In the
event of low-frequency hum, engage the Ground Lift
switch. The ground circuit is severed when this
button is pressed. If this doesn’t solve the problem,
check for damage to any cord connected to ELIAS PX
as well as all cords routing signals to the mixing
console (see also Tips and Tricks).

3 Line In

Connecting cords: Connect cords carrying signals
from your mixer (master left/right, line out, or a
similar circuit) to the balanced inputs using a mic
cord equipped with XLR connectors.
Ensure XLR connectors are wired as follows:
1= ground, 2= +, 3= -.

4 Line Through

Connecting cords: Use this parallel output to route
the incoming line signal to other components (for
example, additional ELIAS PX systems or other com­ponents) via XLR cords.

5 Gain

Operation: Use this knob to adjust the input signal
level. The standard setting is 0 dB at the 12 o’clock
position. For weaker signal sources such as small
mixers equipped with unbalanced circuitry and RCA
connectors or _" jacks, you can boost levels by up to
+6 dB (twist the Gain knobs to the far right).

6 Fan

This ventilator keeps the power amp modules cool.
Always make sure that the fan and the vents are free
of dirt and debris and that they remain unobstructed
so air can circulate freely.

7 Circuit Breaker

Operation: This automatic circuit breaker serves the
same purpose as a standard fuse. If it trips, first
switch the system off entirely (Power switch set to
OFF). Then after you have identified and fixed the
problem, you can reset the circuit breaker by simply
pressing it.

8 Mains Input

Connecting cords: Use the factory-included mains
cord to connect this socket to a wall receptacle.
Caution! Make sure the local mains voltage matches
the voltage specified on the device. If you connect
the system to the wrong mains voltage, you may
destroy the ELIAS PX system’s electronic
components.

9 Power Switch

Operation: This is the on/off switch for the active
system. When engaged, the Power On LED lights up.
Always switch the ELIAS PX active system on last,
that is, after powering up all other components such
as the mixing console, and switch it off first before
powering down all other connected devices.

10 Power On LED

This LED lights up when the Power switch is set to
On and the system is connected to a mains power
supply.

11 Mains Cord Cleat

Secure the power cord with this cleat to prevent it
from being pulled out inadvertently.

5 Tips and Tricks

1 Do not expose electronic circuitry to moisture!
When you set the system up outdoors, be sure to
protect it against rain. Keep soft drinks, beer and all
other liquids well away from the cabinets to protect
their electronic components from short-circuiting.

2 Ensure that the vents on the enclosures’ rear
panels are free of dirt and the devices are ventilated
properly. Otherwise, the electronic components are
likely to overheat and be damaged by thermal
breakdown.

ELIAS EPX 112 A controls

1

2

10

3

4

5

6

9

7

8

11

9

English

3 ELIAS PX delivers optimum sound, so you should
provide it with optimum input signals! Noise such as
humming is generally caused by defective cables, the
wrong type of cords, or unbalanced signals routed
into the mixing console. Check all signal and mains
cables.

4 Prevent distortion! Not only is it unpleasant to
your audience’s ears, it can also damage your equip­ment. Make sure all components that are connected
directly and indirectly to ELIAS PX have sufficient
power ratings, and that they don’t distort as a result
of operating at or beyond their respective limits.
Provide an undistorted signal to the system in the
first place, so that it doesn’t have to be cleaned up
by backing off the system’s Gain knob.

5 Avoid ground loops! A ground loop can occur when
the mixer and ELIAS PX are each connected to two
different mains circuits. To prevent this problem,
always connect the ELIAS PX system and the mixing
console to the same electrical circuit (same phase!).
If your equipment hums despite this precaution, the
Ground Lift switch can be a great help.

CAUTION: Never tape over the plug’s ground
terminal - this endangers lives!

6 ELIAS PX Accessories

HK AUDIO Tilt-Unit

Designed to hold the ELIAS PX mid/high unit, the
tilt unit is placed on the subwoofer, with the Duo­Tilt™ fitting offering a choice of 7.5° or 15 ° angles.

HK AUDIO Dust Covers for ELIAS PX

This set comprises subwoofer and satellite covers.
Extremely tear resistant, water repellant and thickly
padded, these covers afford lasting protection for the
ELIAS PX system during transport.

To learn more about original HK AUDIO accessories,
talk to your HK AUDIO dealer or visit
www.hkaudio.com.

7 Troubleshooting

The Power On LED does not light up when switched
on.

1 Check if the power cord is plugged into the Mains

Input.

2 Check if the mains power supply is providing

current.

3 Check if the house circuit breaker has tripped.

The Power On LED lights up red, but no sound is
coming from the cabinets.

1 Check the cords connected to the inputs.
2 Check if the signal sources (mixer, keyboard, CD

player, etc.) are on.

3 Check if the Gain knobs are turned up.

The subwoofer’s low frequency output is weak.

1 Check the Subwoofer Gain knob’s setting

The signal sounds distorted.

1 Check the LED displays on your mixer. Ensure they

are not constantly in the red. If necessary, back off
the volume at the mixer.

2 If the LED displays on your mixer are in the green,

turn ELIAS PX’s Gain knobs to reduce the input
level.

Annoying hum

1 Check the cords connecting the signal source to

ELIAS PX. Replace damaged cords.

2 If you cannot pinpoint the cause of the hum, press

the Ground Lift switch. This should remedy the
problem in most cases.

ELIAS EPX 115 Sub A controls

2

10

3

4

5

6

9

10

7

8

11

ELIAS PX Manual 1.0

8 Technical Specifications

ELIAS EPX 112 A

Connections: 1x XLR Line In

1x XLR Line Through
Line In: XLR female (pin 1= Ground; 2= +, 3= -)
Input: Electronically balanced & floating
Input impedance: 20 k ohms
Max. input level: +22 dBu
Frequency response +/- 3dB:

1

80 Hz – 19 kHz fullrange mode

130 Hz – 19 kHz satellite mode
Axial sensitivity 1W@1m:

2

104 dB
Maximum SPL @1m:

2

128 dB @ 10% THD
Mid/high-range amplifier: 400 W RMS
Active protection circuitry: Opto limiter, subsonic filter
Midrange speaker: 12"
Tweeter/ driver: 1“
Directivity: 60° x 40° CD horn
Crossover frequency: 2 kHz, 12 dB/ octave
Pole mount: HK AUDIO DuoTilt™, 36 mm, 7.5°, 15°
Accessories: Tilt Unit, 7.5°, 15°

Dimensions (WxHxD): 39 x 58,5 x 45 cm

15" x 23" x 17-7/8"
Weight: 25,5 kg/ 54 lbs.

ELIAS EPX 115 Sub A

Connections: 1x XLR Subwoofer Input

1x XLR Subwoofer Through
Subwoofer Input: XLR female (pin 1= Ground; 2= +, 3= -)
Input: Electronically balanced & floating
Input impedance: 20 k ohms
Max. input level: +22 dBu
Frequency response+/- 3dB: 1) 48 Hz – 130 Hz
Axial sensitivity 1W@1m: 2) 104 dB
Maximum SPL @1m: 2) 126 dB @ 10% THD
Subwoofer amplifier: 400 W RMS
Active protective circuits: DynaClip™ Limiter, Subsonic Filter
Woofer: 15"
Pole mount: M20 thread base plate
Wheels 4x 80 mm casters on the rear panel

Dimensions (WxHxD): 46,5 x 64,5 x 66 cm incl. casters

18-1/4 x 25-1/2 x 26"
Weight: 36 kg/ 79,2 lbs.

11

English

General electrical data:

Protection class 1 (protectively earthed)

Max. current consumption: 2.7 A (230 V)

5.4 A (117 V)

6.3 A (100 V)

Mains voltage 230 V
Power fuse: T 2A (EPX 112 A and EPX 115 A)

Mains voltage 117 V
Power fuse: T 4A or SB 4A (EPX 112 A and EPX 115 A)

Mains voltage 100 V
Power fuse: T 4A (EPX 112 A and EPX 115 A)

Max. power consumption: 690 VA

Mains voltage range: +/- 10%

Ambient temperature range: -10° C to +35° C

Internal fuses: 4x T 4A

1) Via active crossover

2) All measurements taken under half-space conditions

This is to certify that

HK AUDIO®ELIAS PX

complies with the provisions of the Directive of
the Council of the European Communities on the
approximation of the laws of the Member States
relating to electromagnetic compatibility
(EMC Directive 89/336/EEC) and the low voltage
Directive (73/23/EEC).
This declaration of conformity of the European
Communities is the result of an examination carried
out by the Quality Assurance Department of
STAMER GmbH in accordance with European
Standards EN 50081-1, EN 50082-1and EN 60065
for low voltage, as laid down in Article 10 of the
EMC Directive.

Stamer Musikanlagen
GmbH*
Magdeburger Str. 8
66606 St.Wendel

Lothar Stamer Dipl.Ing.
Managing Director
St.Wendel, 04/15/05

* Stamer Musikanlagen manufactures exclusively
for HK AUDIO®.