Hitron TECHNOLOGIES XM2 User Manual

WIRELESS DOCSIS 3.1 METER

DOCSIS 3.1 meter using Intel® Puma™ 7 OFDM 2x2 with 2x2 5GHz
and 2x2 2.4GHz dual band Wi-Fi, LTE, GigE and USB ports

KEY FEATURES

XM2

• DOCSIS 3.1/3.0/2.0/1.1 compliant

• Wi-Fi 2x2 5GHz 802.11ac and 2x2 2.4GHz

802.11n dual band internal antennas

• Wireless connection with smartphone to
initiate tests and display results

• Smartphone App support (IOS / Android)

• 1 x RJ-45 Ethernet port 10/100/1000Mbps

• Two USB 2.0 ports (5V/1A)

• LTE detection

• Battery 9000mAh

• 2 RF connectors (outside & home)

• FAN cooling

• AC detection

• Full frequency spectrum support

• IQ constellation

• Pre-equalizer analysis

• Switchable Upstream 5-85/5-42

• QAM measurements

• Channel plan scan

• Ping and trace route

• Channel plan

• System information

• DOCSIS WAN

• DOCSIS logger

• DOCSIS provisioning status

• MoCA power spectrum display

• Downstream OFDM/OFDMA Metrics

• Fast reposting available QAM channel

• Wi-Fi scan capability including channel utilization

statistics to replace Raspberry Pi

• Speed test (iperf 3, ariac2)

• Buffers for persistence mode analysis

• Firmware & APK Upgrade

Empower technicians to troubleshoot the whole home

XM2 is a powerful troubleshooting tool offering the major tests required to measure both DOCSIS and
DVB-C networking environments. Through MSO partnerships, this wireless DOCSIS 3.1 meter was
specially tailored to the requirements faced by installers and service technicians in the field.

The XM2 is a cable/DVB-C probe with 1 Gigabit Ethernet port and 802.11b/g/n/ac wireless LAN Access
Point combined into one device to simplify cable connectivity testing and troubleshooting. The unit
contains a DOCSIS 3.1/3.0/2.0/1.1 compliant cable modem to insure interoperability with existing
cable systems. Through the use of technicians’ smartphones and our specifically-designed app (iOS &
Android), Hitron aims to offer the most cost-efficient testing solution containing the major features
MSOs require.

The XM2 also features a speed test function for proofing the customer’s premise as well as the outside
network. It enables customizable DOCSIS logging functions that allow increased visibility and details.

Hitron HQ - www.hitrontech.com

No. 1-8, Lihsin 1st Rd, Hsinchu Science Park

Hsinchu, Taiwan

Tel: [phone]

USA - www.hitron-americas.com

9000 E Nichols Ave

Centennial CO 80112 Suite 103

Tel: [phone]

Europe - www.hitron-europe.com

Kingsfordweg 151 1043 GR

Amsterdam, The Netherlands

Tel: [phone]

SPECIFICATIONS

XM2

Connectivity

• 2 x RF F-type male 75Ω connector

• LTE antenna 700 MHz ~ 1.8GHz

• 1 x RJ-45 Ethernet port 10/100/1000 Mbps (Auto-

MDI/MDIX)

• 2 x USB2.0 (5V, 1A)

Management

• App-based GUI for configuration and management

• Protocol support: SNMP v1, v2C, v3

• Power on self diagnostic

• MIB II/MCNS MIB

• Hitron proprietary MIBs for extended support

Reception-Demodulation

• DOCSIS 3.1/3.0/2.0 /1.1

• DOCSIS 3.1 demodulation: Multi-carrier OFDM 16

to 4096QAM

• DOCSIS 3.1 data rate: Up to 5Gps with 2 OFDM
192MHz downstream channels +32 QAM

• DOCSIS 3.0 demodulation: 64QAM, 256QAM

• DOCSIS 3.0 data rate: Up to 1.2Gbps with 32

bonded downstream channels

• Frequency (edge-to-edge):
108~1218MHZ/54~1218MHz (EuroDOCSIS/DOCSIS)

1350~1675MHZ(MoCA2.0)

• Channel bandwidth: 6/8 MHz (DOCSIS 3.0)

100Mhz (MoCA2.0)

• Signal level: -15dBmV to 15dBmV

• Input return loss: >6dB

Transmitter-Modulation

• DOCSIS 3.1/3.0/2.0 /1.1

• DPCSOS 3.1 modulation: Multi-carrier OFDMA

96MHz US channels

• DOCSIS 3.0 modulation: QPSK, 8QAM, 16QAM,
32QAM, 64QAM, and 128QAM (SCDMA only)

• DOCSIS 3.0 data rate: Up to 320Mbps with 8
bonded upstream channels

• Frequency: switchable 5-85/5-42MHz

1350~1675Mhz(MoCA2.0)

• Upstream transmit signal level: +11 to 65dBmV

• Output return loss: >6dB

Wireless

• Dual band Wi-Fi

• 802.11a/b/g/n/ac

• 2T2R 5GHz (5180MHz-5240MHz band 1, 5748-5825MHz

band 4) 802.11ac with 400Mbps PHY data rate

• 2T2R 2.4GHz (2412MHz-2462MHz) 802.11n with
150Mbps PHY data rate

• 20/40MHz channel bandwidth

• Up to 4 SSIDs for each frequency

• Security: WPS, WPA, WPA2, WPA-PSK and 64/128- bit

WEP encryption

• Wi-Fi output power Range :

Mechanical

• 7 status LEDs (Power, Wi-Fi, DS, US, Status, Charge, Bat)

• Factory reset button

• Power restart button

• Dimensions: 165mm (W) x 210mm (H) x 79mm (D)

• Weight: 1100g ± 10g

Electrical

• Power adaptor: 100-240VAC to 12VDC, 50/60Hz, 5A

• Power input: 12VDC

• Power consumption: 32W (typical), 48W (max)

• Battery: lithium battery cells 9000mAh

(8h of typical operation, 4.5h full load, 4h to charge)

• Surge protection: RF input sustains at least 4KV,

Ethernet RJ-45 sustains at least 4KV

Environmental

• Operating temperature: 0°C (32°F) - 40°C (104°F)

• Operating humidity: 10% - 90% (non-condensing)

• Storage temperature: -40°C (-40°F) - 80°C (176°F)

Compliance Certificates

• FCC, IC, UL

• RoHS compliant

• IP20

XM2_2018_1A - Issued Apr 2018

Specifications subject to change without further notice

Trademarks owned by Hitron Technologies Inc. 2018 © Hitron Technologies Inc. – All rights reserved

Federal Communication Commission Interference

Statement

•

• This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.

•

• This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one of
the following measures:

•

• - Reorient or relocate the receiving antenna.

• - Increase the separation between the equipment and

receiver.

• - Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.

• - Consult the dealer or an experienced radio/TV
technician for help.

• FCC Caution: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate this equipment.

• This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.

• Operations in the 5.15-5.25GHz band are restricted to
indoor usage only.

•

Radiation Exposure Statement:

• This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with
minimum distance 25 cm between the radiator & your
body.

• Industry Canada statement:

• This device complies with ISED’s licence-exempt RSSs.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.

• Le présent appareil est conforme aux CNR d’ ISED applicables
aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) le dispositif ne doit
pas produire de brouillage préjudiciable, et (2) ce dispositif doit
accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.

• Caution :

• (i) the device for operation in the band 5150-5250 MHz is only

for indoor use to reduce the potential for harmful interference
to co-channel mobile satellite systems;

• (iii) where applicable, antenna type(s), antenna models(s), and
worst-case tilt angle(s) necessary to remain compliant with the
e.i.r.p. elevation mask requirement set forth in section 6.2.2.3
shall be clearly indicated.

• Avertissement:

• (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz

sont réservés uniquement pour une utilisation à l’intérieur afin
de réduire les risques de brouillage préjudiciable aux systèmes
de satellites mobiles utilisant les mêmes canaux;

• (iii) lorsqu’il y a lieu, les types d’antennes (s’il y en a plusieurs),
les numéros de modèle de l’antenne et les pires angles
d’inclinaison nécessaires pour rester conforme à l’exigence de
la p.i.r.e. applicable au masque d’élévation, énoncée à la
section 6.2.2.3, doivent être clairement indiqués.

• Radiation Exposure Statement:

• This equipment complies with ISED radiation exposure

limits set forth for an uncontrolled environment. This equipment
should be installed and operated with greater than 30 cm between
the radiator & your body.

• Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux
rayonnements ISED établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé à plus de 30 cm entre le
radiateur et votre corps.

Specifications subject to change without further notice

Trademarks owned by Hitron Technologies Inc. 2018 © Hitron Technologies Inc. – All rights reserved