Hit Music CAM-LITE 200 OPERATION MANUAL

ENGLISH OPERATION MANUAL
JB SYSTEMS® 1/10 CAM-LITE 200
Thank you for buying this JB Systems® product. To take full advantage of all possibilities and for your own safety, please read these operating instructions very carefully before you start using this unit.
FEATURES
Budget friendly Lightpanel for livestreaming and small
Compact but powerful output: 2400 CW / WW 0,2W LEDs with 210W total power
Tunable white 3000K → 6300K
4 leaf barndoor included
Beam angle 110°
Flicker free dimming with refresh rates between 800Hz and 25kHz
Four dimmer curves: linear, square, inverse square, S-curve
Easy stand-alone use: 2 rotary knobs for dimming and color temperature adjustment.
Full DMX control with 2 modes
Wireless DMX (optional WTR dongle) or cabled XLR 3pin in/outputs
Cooling by natural convection (no noisy fans)
Lock function to avoid unwanted altering of the settings.
Rubber feet on the back for use as up-light projector.
Color LCD display.
PowerCON compatible in/outputs for easy daisy chaining.
BEFORE USE
Before you start using this unit, please check if there’s no transportation damage. Should there be any, do not use the device and consult your dealer first.
Important: This device left our factory in perfect condition and well packaged. It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual.
Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user manual.
Check the contents:
Check that the carton contains the following items:
Operating instructions
CAM-LITE 200 unit
Power cable
studio lighting.
ENGLISH OPERATION MANUAL
JB SYSTEMS® 2/10 CAM-LITE 200
SAFETY INSTRUCTIONS:
To protect the environment, please try to recycle the packing material as much as possible.
To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when bringing it into
a warm room after transport. Condense sometimes prevents the unit from working at full performance or may even cause damages.
This unit is for indoor use only.
Don’t place metal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign object enters
the unit, immediately disconnect the mains power.
Locate the fixture in a well ventilated spot, away from any flammable materials and/or liquids. The fixture must be fixed at least 50cm from surrounding walls.
Don’t cover any ventilation openings as this may result in overheating.
Prevent use in dusty environments and clean the unit regularly.
Keep the unit away from children.
Inexperienced persons should not operate this device.
Maximum safe ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.
Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging and servicing.
Allow the device about 10 minutes to cool down before to start servicing.
Always unplug the unit when it is not used for a longer time or before to start servicing.
The electrical installation should be carried out by qualified personal only, according to the regulations for electrical and
mechanical safety in your country.
Check that the available voltage is not higher than the one stated on the unit.
The power cord should always be in perfect condition. Switch the unit immediately off when the power cord is squashed
or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Never let the power-cord come into contact with other cables!
This fixture must be earthed in order to comply with safety regulations.
Don’t connect the unit to any dimmer pack.
Always use an appropriate and certified safety cable when installing the unit.
In order to prevent electric shock, do not open the cover. There are no user serviceable parts inside.
Never
repair a fuse or bypass the fuse holder.
Always
replace a damaged fuse with a fuse of the same type and
electrical specifications!
In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
The housing and the lenses must be replaced if they are visibly damaged.
Please use the original packing when the device is to be transported.
Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
Important:
Never look directly into the light source! Don’t use the effect in the presence of persons suffering from epilepsy.
CAUTION: To reduce the risk of electric shock, do not remove the top cover. No user-serviceable parts inside. Refer servicing to qualified service personnel only.
The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying this appliance.
This symbol means: indoor use only
This symbol means: Read instructions
This symbol determines: the minimum distance from lighted objects. The minimum distance between light­output and the illuminated surface must be more than x meters
CAUTION: Do not stare at operating lamp. May be harmful to the eyes.
ENGLISH OPERATION MANUAL
JB SYSTEMS® 3/10 CAM-LITE 200
DESCRIPTION:
1. HANGING BRACKET: You can use the hole in the center of the bracket to fix a hook or truss clamp.
2. KNOB FOR HANGING BRACKET: For tightening the hanging bracket to keep it in its position.
3. BARNDOORS (SMALL): To delimit the beam in horizontal directions.
4. BARNDOORS (BIG): To delimit the beam in vertical directions.
5. BUTTONS: to select different options of the setup MENU:
MENU-button: used to enter/exit the setup MENU.
-button: used to go to the next MENU option or to decrease a parameter value.
-button: used to go to the previous MENU option or to increase a parameter value.
ENTER-button: used to select a MENU option or confirm a setting.
6. DISPLAY: shows the information on the different modes and functions.
7. Indicator LEDs [MASTER-DMX]
8. Rubber foot.
9. MAINS INPUT: Lockable Power Connector 10A - Neutrik PowerCON® compatible. Connect the supplied
mains cable or an extension cable here.
10. MAINS OUTPUT: used to daisy chain the power to several other projectors. Always pay attention to the
maximum load while adding projectors! Special Multi cables (PowerCON® + DMX XLR-cables are optionally available: see our website!)
11. DMX IN: 3pin XLR connector used to connect the projector with other units or a DMX-controller. The DMX-
input is also used to update the firmware of the projector, see the upgrade instructions on our website.
12. DMX OUT: 3pin XLR connector used to daisy chain the projector with other units.
13. M-DMX INPUT: Please note that this USB-connector is NOT used for updates or to connect the unit to a
PC! Instead this USB-connector makes it very easy to add wireless DMX to the unit! Just add the (optional) WTR-DMX DONGLE from BRITEQ® and you will get wireless DMX! Moreover you will be able to connect other DMX-controlled equipment to the DMX-output so you can share the wireless DMX function with all connected units! No extra settings to be made in the setup menu, just follow the procedure in the user manual supplied with the WTR-DMX DONGLE from BRITEQ®. The separate WTR-DMX DONGLE is available from WWW.BRITEQ-LIGHTING.COM (order code: B04645)
14. FUSE HOLDER
15. COLOR TEMP KNOB: to increase or decrease the color temperature between 3000K and 6300K
16. DIMMER KNOB: to increase or decrease the light output level from 0 to 100%
SETUP MENU:
This is the list of all the functions in the machine.
To select any of these functions, press the [MENU] button and use the [▲/▼] buttons to browse the menu.
Select the desired function with the [ENTER] button.
Use [▲/▼] buttons to change the mode or value.
Once the required mode or value is selected, press the [ENTER] button to select.
Loading...
+ 11 hidden pages