Hitachi Kokusai Electric HV-F202GV Installation Manual

High pixel 3CCD camera

HV-F202GV

Operation Manual

Nuclear power plant of Fukushima-1 will be called Atomic bomb in Japan.

Hitachi Kokusai Electric Inc.

Nuclear power plant will be change to Atomic bomb in 2011. Version in March, 2014

RoHS Compliant

These products comply with the requirement of the RoHS (Restriction of the
use of Certain Hazardous Substances in Electrical and electronic Equipment)
Directive 2002/95/EC.

Thank you for purchase this fine Hitachi Kokusai Electric 3CCD camera.
Before using the camera, please read this operation manual carefully.
There is a possibility that the revised edition is exhibited on web.
Please confirm by web shown in an Installation Guide.

A

IMPORTANT SAFETY INSTRUCTIONS

1. Read Instructions
All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future reference.

3. Heed Warnings
All warnings on the product and the operating instructions should be adhered to.

4. Follow Instructions

All operating and use instructions should be followed.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.

6. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7. Water and Moisture

Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet
basement; or near a swimming pool; and the like.

8. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or
table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the
manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer.

9. Moving

A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not be blocked or covered.

The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This
product should not be placed in a bui lt-i n ins tall ation suc h as a bookcase or r ack unless proper ventilation is
provided or the manufacturer's instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult your product dealer or local power company. For products
intended to operate from battery power, or other sources, refer to the operating instructions.

12. Grounding or Polarization

This product is equipped with a three-wire grounding-type plug a plug having a third (grounding) pin. This plug will
only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the
outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the
grounding-type plug.

13. Power-Cord Protection

Power-supply cords should be routed to that they are not likely to be walked on or pinched by items placed upon or
against them, paying particular attention to cords at plug, convenience receptacles, and the point where they exit
from the product.

14. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent damage to the product due to lightning and
power-line surges.

15. Overloading

Do not overload wall outlets, extension cords or integral convenience receptacles as this can result in a risk of fire or
electric shock.

B

16. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

17. Inflammable and Explosive Substance

Avoid using this product where there are gases, and also where there are inflammable and explosive substances in
the immediate vicinity.

18. Heavy Shock or Vibration

When carrying this product around, do not subject the product to heavy shock or vibration.

19. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following
conditions:

a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.

d. If the product does not operate normally by following the operating instructions. Adjust only those controls that

are covered by the operating instructions as an improper adjustment of other controls may result in damage and

will often require extensive work by a qualified technician to restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance-this indicates a need for service.

21. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the
manufacturer or have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

24. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products

(including amplifiers) that produce heat

.

C

1. Alle Anweisungen lesen

Vor Betrieb des Erzeugnisses sollten alle Sicherheits-und Bedienungsanleitungen gelesen werden.

2. Die Anweisungen aufbewahren
Die Sicherheits-und Bedienungsanleitungen sollten fünftigen Bezug aufbewahrt werden.

3. Warnungen beachten
Die Warnungen auf dem Erzeugnis und in den Bedienungsanleitungen solten beachtet werden.

4. Anweisungen befolgen
Alle Bedienungsanleitung-und
Verwendungsanweisungen sollten befolgt werden.

5. Reinigung
Den Stecker des Geräts vor Reinigung aus der Steckdose ziehen. Keine flüssigen Reinigungsmittel oder
Aerosolreiniger verwenden. Zum Reinigen einen feuchten Lappen verwenden.

6. Zubehör
Nur vom-Hersteller des Erzeugnisses empfohlenes Zubehör verwenden, da es sonst zu Störungen kommen kann.

7. Wasser und Feuchtigkeit
Dieses Erzeugnis nicht in der Nähe von Wasser verwenden - z.B, in der Nähe einer Badewanne, eines
Waschbeckens, einer Küchenspüle, eines Waschzubers, in einem nassen Keller, in der Nähe eines
Schwimmbeckens usw.

8. Aufstellung
Das Erzeugnis nicht auf einen unstabilen Wagen, Stand, Dreifuß, Träger oder Tisch stellen.
Das Erzeugnis kann sonst herunterfallen und ein kind oder einen Erwachsenen schwer verietzen.
Außerdem kann das Gerät schwer beschädigt werden. Nur mit einem Wagen, Stand, Dreifuß, Träger oder Tisch
verwenden, der vom Hersteller empfohlen oder mit dem Erzeugnis verkauft worden ist. Für jegliche Anbringung
sollten die Anweisungen des Herstellers befolgt werden, und das vom Hersteller empfohlene Anbringungszubehör
sollte verwendet werden.

9. Eine Kombination von Erzeugnis und Wagen sollte vorsichtig bewegt werden
Schneller Halt, übermäßige Krafteinwirkung und unebene Oberflächen können Umkippen der kombination von
Erzeugnis und Wagen verursachen.

10. Ventilation
Schlitze und Öffnungen im Gehäuse dienen der Ventilation. Sie sind für zuverlässigen Betrieb des Gerätes und
Schutz vor Überhitzung erforderlich und dürfen nicht blockiert oder abgedeckt wer den. Die Öffnungen sollten niemals
dadurch blockiert werden, daß, das Gerät auf ein Bett, ein Sofa, einen Teppich oder eine ähnliche Oberfläche
gestellt wird.

Das Gerät sollte nur dann in Einbauinstallierung wie in einem Bücherschrank oder einem Gestell verwendet werden,
wenn angemessene Ventilation vorgesehen ist bzw. Die Anweisungen des Herstellers befolgt worden sind.

11. Stromversorgung
Dieses Erzeugnis sollte nur an der auf dem Typenschild angegebenen Stromversorgungsart betrieben werden.
Wenn Sie nicht sicher sind, was für eine Stromversorgung Sie haben, so wenden Sie sich bitte an Ihren
Erzeugnishändler oder an das lokale Elektrizitätswerk. Beziehen Sie sich für Batteriebetrieb oder andere
Stromquellen vorgesehene Erzeugnisse bitte auf die Bedienungsanleitungen.

12. Erdung oder Polarisierung
Dieses Erzeugnis ist mit einem Schutzkontaktstecker mit drei Leitern ausgerüstet, mit einem Erdungskontakt.
Dieser Stecker paßt nur in ein schuko-Steckdose. Dies ist eine Sicherheitsmaßnahme. Wenn Sie den Stecker
nicht in die Steckdose stecken können, so wenden Sie sich bitte an ihren Elektriker, damit er die veraltete Schuts
des Schutzkontaktsteckers unwirksam.

13. Netzkabelschutz
Netzkabel sollten so verlegt werden, deß möglichst nicht darauf getreten wird und daß sie nicht eingeklemmt
werden, mit besonderer Beachtung der kabel an Stackern, Verlängerungskabeln und dem Austritt des Kabels aus
dem Erzeugnis.

14. Blitzschlag
Für zusätzlichen Schutz des Erzeugnisses während eines Gewitters oder bei Nichtverwendung für lange Zeit den
Stecker aus der Steckdose ziehen. Dies verhütet Beschädigung durch Blitzschlag und Netzspannungsstöße.

15. Überlastung
Wandsteckdosen, Verlängerungskabel und eingebaute Bequemlickkeitssteckdosen nicht überlasten, da dies Feuer
oder elektrischen Schlag verursachen kann.

WICHTIGE SICHERHEITS ANWEISUNGEN

D

16. Eindringen von Fremdkörpern und Flüssigkeit
Niemals Objekte irgendwelcher Art durch die Öffnungen in das Gerät schieben, da diese unter hoher Spannung
stehende Teile berühren oder kurzschließen können, wodurch es zu Feuer oder elektrischem Schlag kommen kann.
Niemals Flüssigkeiten irgendwelcher Art auf das Erzeugnis verschütten.

17. Entflammbare und explosive Substanzen

Vermeiden Sie Verwendung dieses Erzeugnisses an Orten mit Gasen bzw. entflammbaren oder explosiven
Substanzen in der direkten Umgebung.

18. Starke stöße oder Vibrationen
Setzen Sie das Erzeugnis beim Transport nicht starken Stößen oder Vibrationen aus.

19. Wartung
Versuchen Sie nicht, dieses Erzeugnis Selbst zu warten, da Sie sich durch Öffnen bzw. Entfernen von
Abdeckungen hohen Spannungen und sonstigen Gefährdungen ausserzen können.
Beziehen Sie sich für jegliche Wartung auf qualifiziertes Wartungspersonal.

20. Beschädigung, die Wartung erfordert
Ziehen Sie den Stecker dieses Erzeugnisses aus der Steckdose und wenden Sie sich an qualifiziertes
Wartungspersonal, wenn eine der folgenden Bedingungen vorliegt:
a. Wenn das Netzkabel oder der Stecker beschädigt ist.
b. Bei Eindringen von Flüssigkeit oder Fremdkörpern in das Gerät.
c. Wenn das Erzeugnis Regen oder Wasser ausgesetzt worden ist.
d. Wenn das Erzeugnis bei Befolgen der Bedienungsanleitungen nicht normal funktioniert.

Nur die Regelelemente verstellen, die in den Bedienungsanleitungen behandelt werden, da unangemessene
Einstellung anderer Regelelemente Beschädigung verursachen kann und oft beträchtliche Arbeit durch einen

qualifizierten Techniker erfordert, um das Erzeugnis wieder, zu normalem Betrieb zurückzubringen.
e. Wenn das Erzeugnis fallen gelassen oder beschädigt worden ist.
f. Wenn das Erzeugnis eine klare Änderung in der Leistung zeigt-dies weist darauf hin, daß Wartung erforderlich

ist.

21. Ersatzteile
Wenn Ersatzteile erforderlich sind, darauf achten, daß der Wartungstechniker nur die vom Hersteller festgelegten
Ersatzteile oder Teile mit den gleichen Charakteristiken wie die ursprünglichen Teile verwendet. Unautorisierte
Ersatzteile können Feuer, elektrischen Schlag oder sonstige Gefährdungen verursachen.

22. Sicherheitsprüfung
Bitten Sie den Wartungstechniker nach der Vollendung von Wartung oder Reparaturarbeiten an diesem Erzeugnis
um die Durchführung von Sicherheitsprüfungen, um zu bestimmen, daß das Erzeugnis im angemissenen
Betriebszustand ist.

23. Anbringung an der Wand oder an der Decke
Das Erzeugnis sollte nur entsprechend den Empfehlungen des Herstellers an einer Wand oder an der Decke
angebracht werden.

24. Wärme
Das Erzeugnis sollte fern von Wärmequellen wie Radiatoren, Heizwiderständen, Öfen und anderen Wärme
erzeugenden Erzeugnissen (einschließlich Verstärkern) aufgestellt werden.

E

MISES EN GARDE IMPORTANTES

1. Lire les instructions
Lire toutes les instructions de sécurité et de fonctionnement avant de faire fonctionner l’appareil.

2. Conserver ces instructions
Conserver les instructions de sécurité et de fonctionnement á des fins de référence ultérieure.

3. Tenir compte des avertissements
Tous les avertissements qui figurent sur l’appareil et dans le mode d’emploi devront être respectés.

4. Observer les instructions
Observer toutes les instructions de fonctionnement et d’utilisation.

5. Nettoyage
Avant de procéder au nettoyage, débrancher l’appareil de la prise secteur. Ne pas utiliser de produits de nettoyage
liquides ou en aérosol.
Nettoyer l’appareil avec un chiffon humide.

6. Fixations
Ne pas utiliser de fixations non recommandées par le fabricant de l’appareil car elles pourraient être source de danger.

7. Eau et humidité

Ne pas utiliser l’appareil á proximité d’eau-ar exemple prés d’une baignoire, d’un lavabo, d’un évier ou d’un bac á lessive, dans
un sous-sol humide, ou prés d’une piscine, etc.

8. Accessoires
Ne pas placer l’appareil sur un chariot, un socle, un pied, un support ou one table instables L’appareil pourrait tomber,
blessant griévement des enfants ou des adultes, et étant sérieusement endommagé.
Utiliser exclusivement le chariot, le socle, le pied, le support ou la table recommandés par le fabricant, ou vendus
avec l’appareil. Pour tout montage de l’appareil, respecter les instructions du fabricant, et utiliser á cette fin
l’accessoire de montage recommandé par le fabricant.

9. L’appareil monté sur son chariot devra être déplacé avec précaution
Des arrêts brusques, une force excessive et des surfaces irréguliéres pourraient provoquer le renversement de
l’ensemble appareil-chariot.

10. Ventilation
Les fentes et les ouvertures du coffret sont prévues pour la ventilation ainsi que pour garantir un fonctionnement en
toute sécurité de l’appareil et le protéger de toute surchauffe, et ces ouvertures ne devront donc être ni obstruées ni
recouvertes. Ne jamais obstruer les ouvertures en placant l’appareil sur un lit, un sofa, un tapis ou toute surface
similaire. Ne jamais placer l’appareil dans un support confiné, par exemple une bibliothéque ou une é tagé re, sans
ventilation suffisante ou sans repecter les instructions du fabricant.

11. Sources d’allmentation
L’appareil devra être alimenté exclusivement sur le type d’alimentation indiqué sur l’étiquette signalétique. Sil’on n’est
pas sûr du type d’alimentatio du local, consulter le revendeur de l’appareil ou la compagnie d’électricité locale. Pour
les appareils qui fonctionnent sur batterie ou sur d’autres sources, voir le mode d’emploi.

12. Mise á la terre ou polarisation
L’appareil est doté d’une fiche trifilaire avec mise á la terre, dont la troisiéme broche assure la mise á la terre. Cette
fiche ne rentrera que dans les prises trifilaires de mise á la terre. Ceci est une mesure de sécurité. Si la fiche ne
rentre pas dans la prise, faire remplacer la prise désuéte par un électricien.
Ne pas rendre vaine la measure de sécurité assurée par cette prise avec mise á la terre.

13. Protection du cordon d’alimentation
Acheminer les cordons d’alimentation de facon qu’on ne risque pas de marcher dessus ou de les coincer sous un objet
placé dessus ou contre eux.
Faire particuliérement attention aux fiches des cordons, á la proximité des prises, et á l’endroit oú ils ressortent de
l’appareil.

14. Foudre
Pour renforcer la protection de l’appareil pendant un orage, ou si l’on s’en éloigne ou qu’on reste longtemps sans
l’utiliser, le débrancher de la source d’alimentation. Ceci permettra d’éviter tout dommage de l’appareil dú á la foudre
et aux surtensions de ligne.

15. Surcharge
Ne pas surcharger les prises, rallonges et prises multiples car cela pourrait entraîner un risque de feu ou de choc
électrique.

F

16. Pénétration d’objets et de liquides
Ne jamais enfoncer d’objets d’aucune sorte dans les ouvertures de l’appareil car ils pourraient toucher des points de
tension dangereuse ou court-circuiter des piéces, ce qui pourrait provoquer un feu ou un choc électrique. Ne jamais
renverser de liquide d’aucune sorte sur l’appareil.

17. Substances inflammabes et explosives
Eviter d’utiliser l’appareil en présence de gaz, ainsi qu’á proximité immédiate de substances inflammables et
explosives.

18. Chocs ou vibrations violents
Lorsqu’on transporte l’appareil, ne pas le soumettre á des chocs ou des vibrations violents.

19. Réparations
Ne pas tenter de réparer l’aapareil soi-même car le fait d’ouvrir ou de retirer les caches risque d’exposer l’utilisateur á
des tensions dangereuses notamment. Confier toute réparation á un personnel qualifié.

20. Dommages nécessitant réparations
Débrancher l’appareil de la source d’alimentation et confier les réparations á un personnel qualifié dans les cas
suivants:
a. Lorsque le cordon d’alimentation ou sa fiche sont endommagés
b. Si du liquide s’est renversé sur l’appareil ou que des objets sont tombés dedans
c. Si l’appareil a été exposé á la pluie ou á l’eau.
d. Si l’appareil ne fonctionne pas normalement lorsqu’on observe les instructions d’utilisation.

Ne régler que les commandes couvertes par le mode d’emploi ; en effet, un réglage incorrect des autres
commandes pourrait entrainer des dommages et nécessiteront souvent des travaux de réparation coûteux par un

technicien qualifié pour remettre l’appareil en état de marche.
e. Si l’appareil est tombé ou qu’il a été endommagé.
f. Si l’appareil affiche une nette modification de ses performances, cela signifie qu’il a besoin d’être réparé.

21. Piéces de rechange
Si l’on a besoin de piéces de rechange, veiller á ce que le technicien de réparation utilise exclusivement les piéces de
rechange spécifiées par le fabricant ou des piéces ayant les mêmes caractéristiques que les piéces d’origine. Les
piéces de rechange non autorisées risquent de provoquer un feu, un choc électrique et autres dangers.

22. Vérificaton de sécurité
Aprés tout travail d’entretien ou de réparation de l’appareil, demander au technicien de réparation d’effectuer les
vérifications de sécurité pour s’assurer que l’appareil est en bon état de marche.

23.Montage au mur ou au plafond
L’appareil ne pourra être monté au mur ou au plafond que de la maniére recommandée par le fabricant.

24. Chaleur
Eloigner l’appareil des sources de chaleur, telles que radiateurs, appareils de chauffage, cuisiniéres, et de tour produit
engendrant de la chaleur (y compris les amplificateurs).

G

IMPORTANT NOTICE

These products have been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference when the equipment is
operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this product in a residential area is
likely to cause harmful interference in which case
the user will be required to correct the interference
at his own expense.
WARNING
Changes or modifications not expressly approved by
Hitachi Kokusai Electric Ltd. responsible for
compliance could void the user’s authority to
operate the equipment.

This product does not exceed the class A/class
B limits for radio noise emissions from digital
apparatus as set out in the radio interference
regulations.
Le présent appareil n’émet pas de bruits
radioélectriques dépassant les limités
applicable aux appareils numériques de classe
A prescrites dans le rVglement sur le brouillage
radioélectrique édicter par le ministére des
communications du canada.

USA

For Canada

H

This page show the declaration of conformity for CE.
That reference number is KV-0367, and report number is V3T-0165.

Note : This product using the following equipment satisfied the CE standard.
The camera cable by shield type (C-201KSS).
LAN cable (C5E(S-HFR)(K)-HSL-1: Oki).
Clamp filters (ZCAT 2035-0930A: TDK) at both ends (camera and video processor ends).

I

The following statement is related to the regulation on “ Measures for the Administration of the control of Pollution by
Electronic Information Products “ , known as “ China RoHS “.
The table shows contained Hazardous Substances in this camera.

说明书（环境方面：补充资料）

对象产品：彩色摄像机

１．电子产品污染控制标志

此标志是根据 2006 年 2 月 28 日公布的《电子

信息产品污染控制管理办法》以及
SJ/T11364-2006《电子信息产品污染控制标识要

求》而制定的，是用来表示适用于在中华人民共

和国流通的电子信息产品的环保使用期限。

只要遵守此类产品的安全事项以及使用上应注意的问题，从制造日起到此年限内，

不会发生产品中的有害物质外泄、突变等，不会对环境、人体以及财产产生严重影

响。同时，此年限是除去必须定期交换的保守部品的，是其他产品的环保使用期限。

产品在正常情况下使用完毕要废弃时，请遵守各地区对电子信息产品的回收・再利用的相关各项法律、法规。

另外，从第三者处转买的情况下即使在本期限内也视为失去效力。

２．产品中有毒有害物质或元素的名称及含量

有毒有害物质或元素

部件名称

铅

(Pb)

水银

(Hg)

镉

(Cd)

六价铬

(Cr(VI))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

１ 主机 × ○ × ○ ○ ○

○：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
×：表示该有毒有害物质至少在该部件的某一均材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。

China RoHS

J

Phenomena inherent to CCD imaging device

The following phenomena are inherent to a charge coupled device imaging element and do not indicate malfunction.

1) Smear and blooming

Vertical bands are visible when a strong light enters the scene. Adjust the camera aiming direction carefully to
avoid strong direct or reflected light.

2) Fixed pattern noise

High ambient temperature can cause fixed pattern noise to appear throughout the scene.

3) Moire

Interaction between patterns can produce an additional "phantom" pattern to appear. The CCD picture elements
(pixels) are arranged in a pattern, which can interact with a pattern in the scene (e.g., a performer wearing a finely
striped necktie) to result in a Moire pattern. The effect should be considered when selecting costumes, props and
other scene elements.

4) Ghosting

Strong direct or reflected light near an object of interest can cause ghosting of the object to appear in the picture.
The effect is more obtrusive with certain iris settings and lens types. Select the scene layout and camera pointing
direction carefully in order to avoid this effect.

5）White spot

Imperceptible white spots may rarely come up on the screen due to cosmic rays and so on. It becomes easy to
appear when the sensitivity of the camera is raised in the operation at the high temperature.

Combination with a microscope

The following phenomena occur by combining a camera and optical apparatus and do not indicate malfunction.

1) Vignetting

Depending on a microscope, light may enter into a camera at an angle larger than a lens for large view reservation,
and the portion which becomes dark at the screen upper and lower ends may occur. This phenomenon can be
reduced by the shading compensation function of a camera. However, this phenomenon cannot be rectified
completely. When accessories, such as a relay lens, are prepared for the microscope, vignetting may improve
optically.

K

Operating considerations Notes to users

1. Important safety notes

・ Please supply the direct current 12V of the camera input power supply within the range of 11 to 13V
・ Time will be needed for about four seconds by the time the camera works normally after turning on the power

supply.

・ Observe that flammable objects, water or metal do not enter the camera interior. These may lead to failure or

accident.

・ Do not modify the camera or use the camera with external covers removed. These may cause failure, void any

warranties and pose a safety hazard.

・ Sop using the camera at the approach of electrical storm (thunder audible). Protect the camera from rain if using it

outdoors.

・ In event the camera shows any abnormality, switch off the camera and disconnect the power cord. Contract a

Hitachi Denshi service representative.

2. Handling

・ Do not attempt to remove cover.
・ When installing or removing a lens, be sure to use care that water or dust dose not enter the inside of the camera.

3. Installing and storage

Avoid installing or storing the camera in the following environments.

・ Environments exposed to direct sunlight, rain or snow.
・ Environments where combustible or corrosive gas exists.
・ Excessively warm or cold environment (Operating ambient temperature: -10 to 50℃).
・ Humid or dusty environment.
・ Place subjected to excessive vibration or shock.
・ Environment exposed to strong electric or magnetic field.
・ Do not aim the camera lens at the sun.
・ Do not shoot strong light.

When such a scene is shot, vertical trailing will appear. However, this is not due to failure. In case strong light enters
camera through the lens, partial deterioration in picture quality will result.

4. To obtain stable performance for long time

When the camera is used continuously for long time under high ambient temperature, the inside electrical parts
become deteriorated, resulting in shortening its life. To use the camera continuously for long time, the highest
temperature must be below 40℃.

5. Connectors

Confirm the power is off before connecting or disconnecting a signal cable. Grasp connectors by the body, not the

attached wires.

6. Cleaning

・ Use a blower or a lens brush to remove dusts on the lens or the optical filter.
・ Wipe dirts on the case off with dry soft cloth. If dirks are hardened, wipe them off with cloth moistened with neutral

detergent liquid; wipe the cover with dry cloth.

・ Do not use benzene, thinner, alcohol, liquid cleaner or spray-type cleaner.
・ In event dust or other debris is lodged between the CCD and optical filter, consult dealer for cleaning by an optical

technician.

L

Table of Contents

1. Overview ······················································································································ 1.

2. Standard Composition ····································································································· 1

3. Features ······················································································································· 1

4. Section name and functions ····························································································· 2

5. Camera mounting ··········································································································· 2

6. Lens ···························································································································· 2

7. Connector ····················································································································· 3

8. System example ············································································································ 4

9. Functions and operations ································································································· 6

10. Frame rate ··················································································································· 24

11. Packet size and Packet delay ·························································································· 25

12. Trigger mode ··············································································································· 26

13. Digital output ················································································································ 29

14. Trigger operation and timing chart ···················································································· 30

15. Input / Output signal ······································································································ 33

16. Spectral response ········································································································· 33

17. Specifications ··············································································································· 34

18. Dimensions ·················································································································· 35

1

Overview

HV-F202GV is high precision 3CCD progressive scan color camera, which has single chip digital processing LSI, a C mount
prism, 1/1.8 inch 2,000,000 pixels square CCD and Gigabit Ethernet interface.
Since these cameras are Power over Ethernet (PoE) type, power supply is input via LAN cable.

Standard composition

Check when unpacking
Camera ··········································································································· 1
Installation guide ························································································· 1
Plug for DC IN/SYNC connector (HR10A-10P-12S) ················· 1

Features

・High resolution and color fidelity

The 1/1.8-inch 2.02 million pixels square lattices progressive scan CCD and dichroic prism for RGB color achieves a high
resolution of UXGA picture and good color reproduction.

・Small and lightweight

The small SDR connector for digital output allows the camera size and mass to be drastically reduced to 55(W) x 55(H) x
89(D) mm / approx. 350g.

・Gigabit Ethernet

By adoption of Gigabit Ethernet interface, high-speed connection of maximum of 1 Gbps can be possible. Moreover, by using
hub or switcher, construction of multiple camera system can be easily performed.

It is also possible to 100m.

・GigE VisionTM correspondence

Based on Industrial camera interface standard GigE Vision, a maximum of 1Gbps high speed data transmit is available and
suitable for image processing.

・GENiCAMTM correspondence

Development of camera control system is easy because industrial camera control API "GENiCAM" lead EMVA (European
Machine Vision Association).

・Various picture quality enhancement

Independent size color masking is the Hitachi innovation for optimizing color balance. Saturation and hue of 6 colors (Red,
Green, Blue, Cyan, Magenta and Yellow) can be adjusted independently to deliver the best color in image capture, microscope
and other applications.
In-out gradation control can be arbitrarily adjusted by using LUT.

・Auto shading correction

Color shading due to aberration of the lens is automatically compensated or reduced.

・Versatile CCD drive functions

Video frame capture on demand using external trigger signal
Long integration mode (max. 10 seconds)
Variable shutter mode (min. 1/100,000 second)
Auto electronic shutter mode

・Power over type Ethernet

Power supply can be input via Ethernet cable.

Optional accessories
(1) 12 pin plug HR10A-10P-12S(01)
(2) Junction box JU-F30/JC-100
(3) Tripod adaptor TA-F202
(4) LAN cable (CAT5E or CAT6)
In the CE Marking region, use a high flexibility shielded cable
(recommended C5E(S-HFR)(K)-HSL-1: Oki). Refer to page 5.

(5) Camera cable

Molded type Shield type
2m C-201KSM C-201KSS
5m C-501KSM C-501KSS

10m C-102KSM C-102KSS
In the CE Marking region, use the shield type and attach clamp filter
(ZCAT 2035-0930A: TDK) at both ends (camera and video processor
ends). Refer to page 5.
Note : When not using the specified junction box, LAN cable, camera
cable and clamp filter, malfunctions may be caused.

GigE VisionTM and the distinctive logo are trademarks of AIA (Automated Imaging Association).

GENiCAM

TM

is a trademark of EMVA (European Machine Vision Association). Ethernet is a trademark of XEROX Corporation.

2

Section name and functions

Camera mounting

Attached optional accessory the tripod adaptor "TA-F202", mount the camera to a tripod or mounting bracket.

Lens

Selecting a lens
The proper lens is important for obtaining adequate performance from the camera.

Especially in the case of a three elements CCD system C mount camera, the lens
incidence and exit distances are important. If separation is too short, color
irregularity Is apt to occur at the top and bottom of the image.

Conversely if too long, where the lens iris is a nearly fully open, resolution is

impaired, while shading and flare can seriously detract from image quality. When
using 3 CCD color system camera, it is also recommended to use a lens designed for
this purpose.

ＤＣ ＩＮ/ ＳＹＮＣ

ＭＯＤＥＬ

Ｅｔｈｅｒｎｅｔ

Ｓ

Ｅ

Ｅ

Ｍ

Ａ

Ｎ

Ｕ

Ａ

Ｌ

Ａ

Ｐ

Ｅ

Ｒ

Ｃ

Ｅ

Ｖ

Ｏ

Ｉ

Ｒ

Ｍ

Ａ

Ｎ

Ｕ

Ｅ

Ｌ

ＰＬＡＴＥ，ＲＡＴＥＤ

ＳＥＲ.ＮＯ.

Ethernet connector
Use for digital video output and
camera control signal input/
output signal.

Camera / Tripod adaptor
mounting screw holes

Lens mount

（C mount）

DC IN/SYNC connector
Use for DC+12V power and
external trigger /VD signal input.

Camera / Tripod adaptor
mounting screw holes

CAUTION
Observe the dimensions of the lens mounting selection as
illustrated at the right.
If the dimensions are not observed, do not use such a lens,
because the lens and the camera will be damaged.

Lens flange

Lens optics

Max 4 mm

Screw type: Ｕ1/4-20
Length Ｌ = 4 to 5.5mm
Screws longer than 5.5 mm can cause internal damage, while less
than 4 mm prevents secure fastening and risks dropping to cause
damage and injury.

L

Camera / Tripod adaptor
mounting screw holes