Hitachi С29-TF641S, С29-TF641SN, С29-TF641ST, С29-TF641SNT, С29-TF651S Service Manual

...

…

HITACHI

HCPT

C29-TF641S/SN/ST/SNT C29-TF651S/SN/ST/SNT

T1-003

SERVICE MANUAL

C29-TF751S/SN/ST/SNT

T1 Chassis

CAUTION :

CONTENTS

SAFETY PRECAUTIONS ...………………...…………….…………………………………………… PRODUCT SAFETY NOTICE …………...…………….………...……………...…………….……… REMOTE CONTROL UNIT ……………..………...…………….…………………………………… GENERAL OPERATIONS GUIDE .………………...…………….……………………………………

Before servicing this chassis, it is important that the service techician reads the " Safety Precaution "

and " Product Safety Notices " in this Service Manual.

CIRCUIT DESCRIPTION …………...…………….…………………………………………………… ADJUSTMENT INSTRUCTIONS ……………………...…………….………………………………… REPLACEMENT PARTS LIST …………………...…………….………………………………………

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.

COLOR TELEVISION

MARCH 2005 Hitachi Consumer Products ( THAILAND ) , Ltd.

SAFTY PRECAUTIONS

WARNING: The following precautions should be

opserved.

1. Do not install , remove, or handle the picture tube in could produce X-radiation moderately in excess of de any manner unless shatter proof goggles are worn. sign levels. The high voltage must not, under any cir People not so equipped should be kept away while cumstances, exceed 34kV on the chassis. picture tubes are handled. Keep picture tube away from the body while handing.

2. When service is required, an isolation transformer receiver is the picture tube. The tube utilized for the should be inserted between power line and the above mentioned function in this chassis is specially receiver before any service is performed on the constructed to limit X - radiatuion. chassis. For continued X-radiation protection, replace tube with

3. When replacing the chassis in the cabinet,ensure all the protective devices are put back in place,such as barriers, non - metallic knobs, adjustment or compartment covers or shields, isolation resistors/ Many electrical and mechanical parts in HITACHI capacitors, etc. television receiver have special safety related

4. When service is required, observe the original lead evident from visual inspection, nor can be protection dressing. Extra precaution should be taken to afforded by them necessarily be obtained by using

assure correct lead dressing in the high voltage

circuitry area. Particularly note the R. G. B. lead wattage, etc. Replacement parts which have these dressing. Ensure they are dressed well away from special safety characteristics are identified by marking the horizontal scan and F.B.T. circuitry. with a on the schematics and replacement

5. Always use the manufacturer ' s replacement component. Always replace original spacers and safety characteristics as the HITACHI recommended maintain lead lengths. Especially critical components replacement one, shown in the parts list in this Service are indicated thus on the parts list and Manual, may create electrical shock, fire, X - radiation, should not be replaced by other makes. Furthermore, where a short circuit has occurred, replace those components that indicate evidence of Product Safety is continuously under review and new overheating. instructions are issued from time to time. For the latest

6. Before returning a serviced receiver to the customer, Manual. A subscription to ,or additional copies of the service technician must thoroughly test the unit HITACHI Service Manuals may be obtained at a nominal to be certain that it is completely safe to operate charge from your HITACHI sales offices. without danger of electrical shock, and be sure that no protective device built into the instrucment by the manufacturer has became defective, or inadvertenly The line output stage can develop voltages in excess damaged during servicing. Therefore, the following of 25 kV; if the E.H.T cap is required to be removed, checks are recommended for the continued discharge the anode cap to chassis via a high value protection of the customers and service techninians. resistor, prior to its removal from the tube.

HIGH VOLTAGE

High voltage should always be kept at the rated value of the chassis and no higher. Operating at higher voltages may cause a failure of the picture tube or high voltage supply, and also, under certain circumstances

X-RADIATION

TUBES : The primary source of X - radiation in this

the same type as the original, HITACHI approved type.

PRODUCT SAFETY NOTICE

characteristics. These characteristics are often not

replacement components rated for higher voltage,

parts list in this Service Manual.The use of a substitute

replacement component which does not have the same

or other hazards.

information,always consult the current HITACHI Service

TUBE DISCHARGE

INSULATION

Insulation resistantce should not be less than 4.5 Mohm at 500 VDC between the mains poles and any accessible metal parts. Also, no flashover or breakdown should occur during the dielectric strength test, applying 3.2kV AC for two seconds between the main poles and accessible metal parts.

- 2 -

REMOTE CONTROL UNIT

8 9

3 15 13

9 8

3 15 13

Models without Teletext Models with Teletext

POWER ON/OFF SWITCH DEFAULT

1. 11.

2. 12.

INPUT SELECTOR MUTE

3. 13.

VOLUME UP/DOWN CHI/II (FOR NICAM/A2 MODELS)

4. 14.

PROGRAMME UP/DOWN PROGRAMME SELECTOR (DIRECT KEY)

5. 15.

RECALL CURSO

6. 16.

SURROUND SOUND RETURN

7. 17.

MENU COLOR SYSTEM

8. 18.

TIMER SOUND SYSTEM

9. 19.

PICTURE EQUALIZER

10. 20

SOUND T/TEXT FUNCTION KEY (T/TEXT MODELS ONLY)

- 3 -

GENERAL OPERATIONS GUIDE

With this set, all adjustments/settings are performed by selecting from menu screens. Different menu screens and details

of adjustments/settings are shown below. To access the menu screen, press the button, then select the item by

pressing the up/down cursor buttons and adjust by the left/right cursor buttons .

- 4 -

BLOCK DIAGRAM

- 5 -

DJUSTMENT INSTRUCTIONS

HOW TO GO TO SERVICE MODE

1. How to go to adjustment mode no 001 ~ 022

Procedure

(1) Turn TV off by power switch on the TV set.

(2) Press " FUNCTION " button on the TV set and kept depress the button.

(3) Turn TV on by power switch on the TV set.

2. How to go to adjustment mode no 101 ~ 328

Procedure

(1) Set volume to be “0”.

(2) Press button on remote control to go to standby mode.

(3) Press “TV/VIDEO” button on the TV set, and kept depress the button.

(4) Press button on remote control to go to operation mode.

(5) TV will show service table,then please cancel to keep depress the "TV/VIDEO" button.

Note : 1. Press the UP/DOWN cursor buttons

2. Adjust data by the left/right cursor buttons .

3. Press "RECALL" buttons to restore the data.

+B ADJUSTMENT

PREPARATION PROCEDURES

AC input voltage 230 +

2 Turns on the set and set the brightness and contrast +B voltage : TP902

to Max.(Signal : Philips Pattern) GND : TP901

3 After 30 sec heat-run, check & adjust the +B voltage

FREE RUN FREQUENCY ADJUSTMENT

Receive a PAL-I monoscope signal on TV mode.

5V(50Hz)

PREPARATION PROCEDURES

to select adjustment mode no.

djust R954 to obtain +B voltage as below

Select adjustment mode no. 1 and press "MENU" button

one time.

VIF-VCO FREE RUN FREQUENCY ADJUSTMENT

PREPARATION PROCEDURES

Receive a PAL-I monoscope signal on TV mode.

Select adjustment mode no. 2 and press "MENU" button

one time.

- 6 -

SOUND TRAP FREQUENCY ADJUSTMENT

PREPARATION PROCEDURES

Receive a PAL-I monoscope signal on TV mode.

Select adjustment mode no. 3 and press "MENU" button

one time.

SECAM R-Y OFFSET ADJUSTMENT

PREPARATION PROCEDURES

1 Receive a secam color bar signal on Video 2. 1 Select adjustment mode no. 4.

2 Connect oscilloscope probe to pin 5 of E701. 2 Adjust output level at pin 5 of E701 as indicated below

using service mode no. 4.

0.1 V

0 +

SECAM B-Y OFFSET ADJUSTMENT

PREPARATION

1 Receive a secam color bar signal on Video 2. 1

2 Connect oscilloscope probe to pin 5 of E701. 2

Select adjustment mode no. 5.

djust output level at pin 5 of E701 as indicated below

PROCEDURES

using service mode no. 5.

0.1 V

0 +

WHITE PEAK LEVEL ADJUSTMENT

PREPARATION PROCEDURES

1 Connect oscilloscope probe to pin 3 of E202 on CPT 1 Adjust output level at pin 3 of E202 as indicated below

P.W.B with respect to ground. using service mode no. 15.

2 Input PAL cross hatch signal to Video 2 terminal.

Cross hatch signal input level : 1 Vpp + 10%(with load

75 ohm) or 2 Vpp + 10%(no load).

3 Set CONTRAST to MAX.

4 Set data in adjustment mode no.15 to 90. A = 2.8 + 0.1Vpp

- 7 -

VERTICAL SHIFT ADJUSTMENT

PREPARATION PROCEDURES

1 Preheat more than 5 minutes of power supply. 1 Select the IIC control address No. 11.

2 Receive PAL Philips pattern signal. 2 Set the horizontal center line to vertical center maker

of CRT by adjustment of IIC.

Vertical center marker of CRT

VERTICAL SIZE ADJUSTMENT

PREPARATION PROCEDURES

1 Preheat more than 5 minutes of power supply. 1 Select the IIC control address No. 12.

2 Receive Philips pattern signal. 2 Adjust IIC data to obtain the following conditions.

PAL

Check vertical amplitude as below by

NTSC circle pattern.

NTSC

4 If picture isn't center, go back to IIC control No. 11 and

adjust IIC data to obtain the following conditions.

- 8 -

SIDE PIN DISTORTION ADJUSTMENT

PREPARATION PROCEDURES

Purity adjustment and convergence adjustment should

be already completed. 2

Set Contrast = 100, Brightness = 50

Set horizontal size adjustment to approximately 2-2 by

1 Receive the circle pattern signal.

Adjust the 1

outer vertical line (R/L) to pin, 2nd outer

vertical line (R/L) to straight using side pin adjustment

(PCC-AMP VR R557 / PCC-PHASE VR R564).

H-WIDTH VR R559. 3 Receive the cross hatch signal.

Vertical amplitude adjustment should be already

4 Check that the vertical line is straight, except 1st outer

completed. vertical line (R/L).

*Pin distortion spec. DL ≤ 3mm ,DR ≤ 2mm*

HORIZONTAL CENTER ADJUSTMENT

PREPARATION PROCEDURES

1 Side pin adjustment should be already completed. 1 Adjust adjustment mode no. 13 so that the average

2 Receive circle pattern signal. reading of R and L is 2.0 +

HORIZONTAL SIZE ADJUSTMENT

PREPARATION PROCEDURES

Horizontal center adjustment should be already

1 Adjust Horizontal size (H-WIDTH VR R559) so that the

completed. average reading of right and left is 2.0 +

2 Receive circle pattern signal.

3 Set Contrast = 100, Brightness = 50

2.0 + 0.5

0.5 at circle pattern signal.

0.5.

2.0 + 0.5

- 9 -

FOCUS ADJUSTMENT

PREPARATION

PROCEDURES

1 Receive Philips pattern signal. 1 Set picture to mode 1

2 Vertical amplitude adjustment should be already 2 Turn the focus VR gradually clockwise from the full

completed. counterclockwise and adjust so that the halo of vertical

3 Adjust the cut-off after pre-adjust focus VR. center line does not appear, and horizontal line is

4 Check the cut-off in case focus is re-adjusted MIN. width.

HORIZONTAL

1 2 3 4 5 6 7

NO.5

ZOOM

HALO

VERTICAL

WHITE BALANCE ADJUSTMENT

PREPARATION

1 Adjust the W/B after the Power is turned ON for 20 minute

1 Turn the screen adjusting VR clockwise and set it to the

PROCEDURES

2 Purity adjustment should be completed. position where the bright line starts appearing on CPT

3 Set the vertical incident illumination on the CPT surface screen.

to 20 lux or less. 2 Take the first appeared color as the reference. Adjust the

4 Receive white raster signal. other colors by remote until both appear to be the same

5 Set adjustment mode data as table on the next page level as the reference. (A white horizontal line is seen at

to default.

Disp No ITEM Default

016

017

018

019

020

021

R-CUTOFF

G-CUTOFF

B-CUTOFF

R-DRIVE

B-DRIVE

SUB-BRIGHT

127

6 Turn the screen adjustment VR fully counterclockwise. 5

7 Set to lateral line mode by Press “MUTE” button on

the CPT center.)

Low brightness adjustment data

Red

Green

Blue

………. ”1” key for up, “4” key for down.

………. ”2” key for up, “5” key for down.

………. ”3” key for up, “6” key for down

Don’t change the data of the reference color

3 Exit the lateral line mode. (Press “MUTE” by remote).

4 Set white balance meter at the center of the screen.

djust brightness control so that the indication of the

brightness meter is a prescribed value of brightness

remote control . adjustment. Adjust white balance with the white balance

control data (Red/Blue).

High brightness adjustment data

Red

Blue

………. ”7” key for up, “0” key for down.

………. ”8” key for up, “9” key for down.

- 10 -

SUB-BRIGHTNESS ADJUSTMENT

PREPARATION PROCEDURES

1 Turn the TV set on and heat run for 20 minutes or more. 1 Press "PICTURE" key until go to picture mode 2.

2 Horizontal size adjustment and side pin adjustment 2 The sub-brightness should be adjusted (Adjustment

should be completed. mode no. 21) using11 steps gray scale (A1-A1) of color

3 Receive Philips pattern signal. bar pattern

Set picture mode 2 as shown below. 3 Adjust until A10 is complete black and A9 is lightly black.

4 Go out from service mode.

CONTRAST : 0

COLOR : 0

BRIGHTNESS : 50

A10A

A8A7A6A5A4A3A2A

5 Adjust picture mode 2 as below.

CONTRAST : 100

COLOR : 60

BRIGHTNESS : 50

6 Press "PICTURE" key until go to picture mode 1.

AGC ADJUSTMENT

PREPARATION PROCEDURES

1 All adjustment except for AGC adjustment should be 1 Select adjustment mode no. 14 (TUNER AGC) and press

completed. Heat-run for more than 5 min. “MENU” key one time. Data will be adjusted automatically

2 Receive signal as table on the next page. 2 .When AGC adjustment is complete,screen should be

3 Set Contrast = 100, Brightness = 50. shown "OK" on the right-top side. It the screen show

4 Set the Sound System and Color System depending on "NG" ,it means AGC adjustment is abnormal.

the broadcast system.

5 Set the antenna input level as specified below.

NO.

014 43 OK

DJUSTMENT 10

"OK"

MODEL T1

DESTINATION ALL

BGSYSTEM

CHANNEL CH10

INPUT SIGNAL Philips Pattern

INPUT LEVEL - 54 dBm / 55dBµ(75Ω)

NO.

014 15 NG

Caution : After AGC adjustment is complete, data in

adjustmentment mode no. 14 should be more than 30.

DJUSTMENT 10

"NG"

If not, please re-check or/and adjust again.

- 11 -

REPLACEMENT PARTS LIST

PRODUCT SAFETY NOTE : Components marked with a have special characteristics important to safety. Before

replacing any of these components, read carefully the PRODUCT SAFETY NOTICE of this Service Manual. Don't degrade the safety of the receiver through improper servicing

NO CCT NO.

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

#I904 #I501

#Q502

#I901 #Q503 #D902

C101 C102 C103 C107 C108 C201 C202 C203 C206 C207 C208 C209 C210 C211 C212 C213 C214 C215 C216 C217 C218 C219 C220 C221 C222 C223 C224 C225 C226 C227

HITACHI HITACHI

PARTS NO. DESCRIPTION THS0401001P THS0402001P THS0403001P THS0404002P THS0405001P THS0405002P

0800358R

CE-1TZ103

0800294R 0800303R 0890092R 0800352R

CE-1TZ104

CE-1TZ103 CE-1TCHJ181

CE-1TZ103

0800352R 0800279R

CE-1TZ103

0800279R 0800279R 0880183R

CE-1TCHJ221

CE-1TZ104

0800352R 0800317R

EL-B10V471R

0800362F 0890092R 0800279R 0890065R 0800277R 0880198R 0880198R

CE-1TZ104

HEAT SINK I904 / I905 HEAT SINK I501 HEAT SINK Q502 HEAT SINK I901 ( L = 60mm ) HEAT SINK Q503 ( L = 40mm ) HEAT SINK D902 ( L = 25mm ) CAP ELEC 1000UF 6.3V M CAP CER 0.01UF 50V Z CAP ELEC 10UF 50V M CAP ELEC 22UF 50V M CAP CER 2200PF 50V M CAP ELEC 470UF 10V M CAP CER 0.1UF 50V Z CAP CER 0.1UF 50V Z CAP CER 0.01UF 50V Z CAP CER 180PF 50V J CH CAP CER 0.01UF 50V Z CAP ELEC 470UF 10V M CAP ELEC 1UF 50V M CAP CER 0.01UF 50V Z CAP ELEC 1UF 50V M CAP ELEC 1UF 50V M CAP POLYESTER 0.015UF 50V J CAP CER 220PF 50V J CH CAP CER 0.1UF 50V Z CAP ELEC 470UF 10V M CAP ELEC 47UF 16V M

CAP ELEC 470UF 10V M 105 CAP ELEC 1000UF 25V M

CAP CER 2200PF 50V M CAP ELEC 1UF 50V M CAP CER 22PF 50V J SL CAP ELEC 0.47UF 50V M CAP POLYESTER 0.22UF 50V J CAP POLYESTER 0.22UF 50V J CAP CER 0.1UF 50V Z

SN ST SNT S

REMARK

- 12 -

+ 26 hidden pages