If you need additional
operating assistance after
reading this owner's manual
or to order replacement
accessories, please call
TOLL FREE : 1-800-448-2244.
VT-FX795A
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
The caution marking is located on the rear of the cabinet.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFEGUARDS
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
ANTENNA
LEAD
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND
CLAMP
GROUND CLAMP
ELECTRIC
SERVICE
EQUIPMENT
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC – NATIONAL ELECTRICAL CODE
S2898A
1. Read Instructions- All the safety and operating instructions should be read
before the appliance is operated.
2. Retain Instructions- The safety and operating instructions should be retained
for future reference.
3. Heed Warnings- All warnings on the appliance and in the operating instruc-
tions should be adhered to.
4. Follow Instructions- All operating and use instructions should be followed.
5.Cleaning- Unplug this video product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted service and, that for
some specific reason, such as the possibility of the loss of an authorization
code for a CATV converter, is not intended to be unplugged by the user for
cleaning or any other purpose, may exclude the reference to unplugging the
appliance in the cleaning description otherwise required in item 5.
6. Attachments- Do not use attachments not recommended by the video prod-
uct manufacturer as they may cause hazards.
7.Water and Moisture- Do not use this video product near water, for example,
near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or
near a swimming pool, and the like.
8. Accessories- Do not place this video product on an unstable cart, stand, tri-
pod, bracket, or table.The video product may fall, causing serious injury to a
child or adult, and serious damage to the appliance. Use only with a cart,
stand, tripod, bracket, or table recommended by the manufacturer, or sold with
the video product. Any mounting of the appliance should follow
the manufacturer's instructions and should use a mounting
accessory recommended by the manufacturer. An appliance
and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance
and cart combination to overturn.
9.Ventilation- Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the video product
and to protect it from overheating, and these openings must not be blocked or
covered.The openings should never be blocked by placing the video product
on a bed, sofa, rug, or other similar surface.This video product should not be
placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to .
10. Power Sources- This video product should be operated only from the type of
power source indicated on the marking label. If you are not sure of the type of
power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources,
refer to the operating instructions.
11. Grounding or Polarization- This video product is equipped with a polarized
alternating-current line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a safety feature. If
you are unable to insert the plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
12. Power Cord Protection- Power supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
13. Outdoor Antenna Grounding- If an outside antenna or cable system is con-
nected to the video product, be sure the antenna or cable system is grounded
so as to provide some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with regard to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode. (Fig.A)
14. Lightning- For added protection for this video product during a lightning storm,
or when it is left unattended and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or cable system. This will prevent
damage to the video product due to lightning and power-line surges.
15. Power Lines- An outside antenna system should not be located in the vicinity
of overhead power lines or other electric light or power circuits, or where it can
fall into such power lines or circuits.When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or
circuits as contact with them might be fatal.
16. Overloading- Do not overload wall outlets and extension cords as this can
result in a risk of fire or electric shock.
17. Object and Liquid Entry- Never push objects of any kind into this video prod-
uct through any openings as they may touch dangerous voltage points or
short-out parts that could result in a fire or electric shock. Never spill liquid of
any kind on the video product.
18. Servicing- Do not attempt to service this video product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
19. Damage Requiring Service- Unplug this video product from the wall outlet
and refer servicing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore the
video product to its normal operation.
e. If the video product has been dropped or damaged in any way.
f. When the video product exhibits a distinct change in performance-this indi-
cates a need for service.
20. Replacement Parts- When replacement parts are required, be sure the ser-
vice technician has used replacement parts specified by the manufacturer or
have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
21. Safety Check- Upon completion of any service or repairs to this video prod-
uct, ask the service technician to perform safety checks to determine that the
video product is in proper operating condition.
22. Heat- This video product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers) that
produce heat.
– 1 –EN
(
)
Display Window
1
234567891011
12
POWER CHANNEL
TRACKING
L-AUDIO IN-RVIDEO IN
REC/IRT STOP/EJECT REW PLAY F.FWD
nm
ab
s
PNV
14
15
16
17
18
13
Remote Control
SLOW
TAPE SPEED
SEARCH MODE
CH
PAUSE
REC
DISPLAY EXITMENU
COUNTER
RESET
MEMORY
POWER
EJECT
0
REW
STOP
PLAY
F.FWD
7
8
9
6
5
4
3
2
1
VCR/TV
1
2
16
17
3
6
7
14
15
12
9
18
11
10
8
13
4
5
Rear Panel
ANT
AUDIO
VIDEO
IN
OUT
OUT IN
OUT
L
R
IN
25
1920 21
242322
(
)
To insert the batteries
PRECAUTIONS
Front Panel
Install Location
For safety and optimum performance of your VCR:
• Install the VCR in a horizontal and stable position. Do not place
anything directly on top of the VCR. Do not place the VCR directly
on top of the TV.
• Shield it from direct sunlight and keep it away from sources of
intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the VCR. Avoid locations subject to strong
vibration or strong magnetic fields.
Avoid the Hazards of Electrical Shock and Fire
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from AC wall
outlet. Grasp it by the plug.
Moisture Condensation Warning
Moisture condensation may occur inside the unit when it is moved
from a cold place to a warm place, or after heating a cold room or
under conditions of high humidity. Do not use the VCR at least for 2
hours until its inside is dry.
FCC Warning
This equipment may generate or use radio frequency energy.
Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the
instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.
DESCRIPTION OF CONTROLS
1. Cassette Compartment
2. F.FWD button
3. PLAY button
4. REW button
5. STOP/EJECT button
6. REC/IRT button
7. Display Window
18. Remote Sensor
19.
CHANNEL/TRACKING
19.
buttons
10. POWER button
11. AUDIO Input jacks
12. VIDEO Input jack
Important Copyright Information
Unauthorized recording or use of broadcast television programming,
video tape, film or other copyrighted material may violate applicable
copyright laws. We assume no responsibility for the unauthorized
duplication, use, or other acts which infringe upon the rights of copyright owners.
A Note about Recycling
This product's packaging materials are recyclable and can be reused.
Please dispose of any materials in accordance with your local recycling regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
Note to the Cable TV System Installer
This reminder is provided to call the Cable TV system installer’s
attention to Article 820-40 of the National Electrical Code, which provides guidelines for proper grounding – in particular, specifying that
the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as possible.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
NOTE:
This product may contain lead and mercury. Disposal of these materials
be regulated due to environmental considerations. For the disposal or
recycling information, Please contact your local authorities or the
Electronics industries Alliance : www.eiae.org.
1. POWER button
2. NUMBER buttons
3. MENU button
4. DISPLAY button
5. PLAY button
6. REW button
7. REC button
8. SEARCH MODE button
9. TAPE SPEED button
10. PAUSE button
11. STOP button
12. F.FWD button
13.
COUNTER RESET/EXIT button
14.
COUNTER MEMORY button
15. SLOW button
16. CH buttons
17. EJECT button
18. VCR / TV button
13. PWR. (POWER) indicator
14. TAPE IN indicator
15. VCR indicator
19. AUDIO OUT jacks
20. AUDIO IN jacks
21. ANT. IN jack
22. ANT. OUT jack
Install two AA batteries
(supplied) matching the
polarity indicated on the
16. REC indicator
17. TIMER indicator
bottom of the remote
control.
18. CLOCK indicator
VIDEO OUT JACK
Connect a video cable going to
the VIDEO IN jack of a camcorder, another VCR, a TV, or an
audio-visual system (laser disc
player, video disc player, etc.)
23. VIDEO IN jack
24. VIDEO OUT jack
25. AC Power Cord
here.
AUDIO OUT JACKS
Connect the audio cables going
to the AUDIO IN jacks of a camcorder, another VCR, a stereo
amplifier, or an audio system
here.
– 2 –EN
VIDEO IN JACK
Connect a video cable coming
from the VIDEO OUT jack of a
camcorder, another VCR, or an
audio-visual source (laser disc
player, video disc player, etc.)
here.
AUDIO IN JACKS
Connect the audio cables coming from the AUDIO OUT jacks
of a camcorder, another VCR, or
an audio source here.
ANT
IN
OUT
[VHF/UHF
combination antenna]
[Back of the VCR]
IN
OUT
[Cable box or satellite box]
OR
[Indoor antenna]
[Back of the
UHF/VHF combination TV]
UHF/VHF
RF cable
(supplied)
From Cable or
Satellite Company
OR
(
)
(
)
(
)
IN
AUDIO
LR
VIDEO
VIDEO
L
R
OUT IN
OUT IN
AUDIO
[Playing VCR]
[TV A/V]
Audio/Video cables
(not supplied)
PREPARATION FOR USE
(
)
ENGLISH
LANGUAGE SELECT
FRANCAIS
AUTO SET UP
CH 01
SETUP
VCR to TV Connection
Disconnect the AC power cord of the TV from the
AC outlet.
1
Disconnect the antenna or cable from the TV.
2
Connect the antenna or cable to the ANT. IN jack of
3
the VCR.
Connect the VCR to the TV using the RF cable.
4
Plug the AC power cords of the VCR and TV into
5
the AC outlets.
RF Output Channel
If your TV does not have A/V terminals:
Press [PLAY] on the VCR for 3 seconds during playback.The
RF output channel will change to CH4 from CH3.
When you want to return to CH3 for RF output channel, press
[PLAY] on the VCR for 3 seconds during playback again.
(Default setting :CH3)
• There is case that the RF output channel does not change by
situation (For example, when you adjust tracking using [CHANNEL].
In this case, stop the playback, and start the playback again.
After that, press [PLAY] on the VCR for 3 seconds.
• If there is a power failure or the VCR is unplugged for more
than 30 seconds, the RF output channel setting will return to
CH3.
VCR to AV TV connection using AUDIO/VIDEO Cables
Using Optional AUDIO/ VIDEO Output Jacks
With this connection, you can get better pictures and sounds
when playing back a tape if your TV has A/V Input jacks.
Please refer to your TV’s owner’s manual.
Using AUDIO/VIDEO Input Jacks
You can use the A/V input jacks on the front or the back of
the VCR.
• To use the input jacks on the back of the VCR, select "L1"
position by pressing [0], [0], [1] on the remote control or
[CHANNEL].
• To use the input jacks on the front of the VCR, select "L2"
position by pressing [0], [0], [2] on the remote control or
[CHANNEL].
•
“L1” or “L2” is found before the lowest memorized channel.
(Example: CH2)
– 3 –EN
Automatic Channel Set Up
You can automatically program the tuner to scan only the
channels you receive in your area.
• Channel memory programming is NOT needed when you
connect the VCR to a cable box or satellite box as in "Connect
VCR to TV Connection". In this case, select the VCR and TV
to channel 3 or 4 the same channel as the RF output channel
of the VCR.Then, the channel you want to record or view may
be selected at the cable box or satellite box.
• Follow the steps below once. Repeat it only if there is a
power failure or if the VCR is unplugged for more than 30
seconds. (In these cases, the programmed channels are
erased.)
• You must follow the steps below before attempting to play or
record a video tape. If you want to play or record a video tape
BEFORE programming the tuner, you can cancel it by pressing [COUNTER RESET/EXIT].
You need to connect the antenna or cable to the
1
VCR first. Then, connect the VCR power plug into a
standard AC outlet.
Turn on the TV and set the TV to channel 3. If chan-
2
nel 3 is already occupied for broadcasting, change the
RF output to CH 4, and change the TV channel to CH4.
(See “RF Output Channel” on page 3 for the detail.)
Turn on the VCR by pressing [POWER]. When the
3
POWER is on, both the POWER and VCR indicators
on the VCR will be on.
Select the On Screen Language
4
("ENGLISH" , "FRANCAIS" or
"ESPAÑOL") by pressing [PLAY] or
[STOP]. Then, press [F.FWD].
Begin channel preset by pressing [F.FWD] once.The
5
tuner scans and memorizes all active
channels in your area.
•
The VCR distinguishes between standard
TV channels and cable channels.
After scanning, the tuner stops on the lowest mem-
6
orized channel. The TV screen returns to TV mode.
• If "AUTO SET UP" appears on the TV screen again, check
the cable connections. Press [F.FWD] once again and the
VCR will begin preset again.
To Select a Desired Channel
You can select the desired channel by using [CHANNEL
] or directly pressing [Number] on the remote control.
Note for using the Number buttons:
• When selecting cable channels which are higher than 99,
enter channel numbers as a three-digit number.(For example: 117, press 1,1,7)
• You must precede single-digit channel numbers with a zero
(For example: 02, 03, 04 and so on).
To Preset the Channel Again
Press [MENU] until the main menu appears.
1
Select "CHANNEL SET UP" by pressing [PLAY] or
2
[STOP]. Then, press [F.FWD].
Select "AUTO SET UP" by pressing [PLAY] or
3
[STOP]. Then, press [F.FWD]. After scanning, the
tuner stops on the lowest memorized channel.
To Add/Delete Channels
(
)
(
)
CLOCK SET
MONTH DAY YEAR
03 / 17 MON 2003
HOUR MINUTE AM/PM
05 : 40 PM AM
PM
Press [PLAY] or [STOP]repeatedly.
Then, press [F.FWD].
Press [PLAY] or [STOP] repeatedly.
Then, press [F.FWD].
The day of the week will appear automatically.
Press [PLAY] or [STOP] repeatedly.
Then, press [F.FWD].
Press [PLAY] or [STOP] repeatedly.
Then, press [F.FWD].
Press [PLAY] or [STOP]
repeatedly.
Press [PLAY] or [STOP] repeatedly.
Then, press [F.FWD].
Set the month
Set the day
Set the year
Set the hour
Set the minute
Set the AM
or PM
- MENU -
TIMER PROGRAMMING
AUTO REPEAT
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
SAP
[OFF]
[ON]
(
)
(
)
When the VCR automatically programs the tuner to scan
only the channels you receive in your area, some channels may be skipped due to weak signal.You can manually add the channel in the VCR memory.
Press [MENU] until the main
1
menu appears.
Select "CHANNEL SET UP" by
2
pressing [PLAY] or [STOP].
Then, press [F.FWD].
Select "MANUAL SET UP" by pressing [PLAY]
3
or [STOP]. Then, press [F.FWD].
Enter the desired channel number by pressing
4
[PLAY] or [STOP].
Add or Delete it from memory by pressing
5
[F.FWD] or [REW] so that "ADD" or "DELETE"
flashes on the TV screen accordingly.
Exit the Preset mode by pressing [COUNTER
6
RESET/EXIT].
To Change the On-Screen Language
Press [MENU] until the main menu appears.
1
Select "LANGUAGE SELECT" by pressing
2
[PLAY] or [STOP]. Then, press [F.FWD].
Select "ENGLISH" , "FRANCAIS" or
3
"ESPAÑOL" by pressing [PLAY] or [STOP].
Then, press [COUNTER RESET/EXIT].
• If you accidentally select Spanish or French and
need English: Press [MENU] and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press
[F.FWD], and select ENGLISH. Finally, press
[COUNTER RESET/EXIT].
Clock Set Up
Select main menu by pressing [MENU].(If the
1
clock is not set, the CLOCK SET menu appears
first. In this case, follow step [3].)
Select "CLOCK SET" by pressing [PLAY] or
2
[STOP]. Then, press [F.FWD].
Set the clock.
3
• To go back one step, press [REW].
Start the clock by pressing [COUNTER RESET/EXIT]
4
or [F.FWD].
PLAYBACK FUNCTION
Normal Playback
Insert the prerecorded tape. The VCR will turn
1
on. If the safety tab has been
removed, the VCR will start playback
automatically.
Turn on the TV and set the TV to channel 3. If
2
channel 3 is already occupied for broadcasting,
change the RF output to CH 4, and change the
TV channel to CH4. (See “RF Output Channel”
on page 3 for the detail.)
Begin playback by pressing [PLAY].
3
• Tracking adjustment will be set automatically
(Digital Tracking function) when you start playback.
To adjust the tracking manually, press
[CHANNEL]
You cannot manually adjust the tracking of a Still
•
picture. However, you may press [CHANNEL]
on the VCR to remove vertical jitter in a Still picture.
• When a tape has reached the end, the VCR will
rewind the tape to the beginning, eject the tape,
and turn off the VCR automatically.
• S-VHS Quasi Playback (SQPB): This unit allows you
to view a tape recorded in S-VHS format. (Noise lines
may appear on the picture.)
on the VCR.
To stop playback, press [STOP].
4
Counter Reset
• You can reset the counter by pressing [COUNTER
RESET/EXIT] on the remote control
Still / Slow
You can freeze the picture on TV screen by pressing
[PAUSE] during playback.
• You can advance the picture by one frame at a time
by pressing [PAUSE] during the still mode.
• If the picture begins to vibrate vertically during the
still mode, stabilize the picture by pressing
[CH].
• If the picture is distorted or rolling vertically, adjust
the vertical hold control on your TV, if equipped.
You can see the slow motion by pressing [SLOW]
during playback or the still mode.
• If the noise bar appears on the TV screen, you can
reduce it by pressing [CH].
• After the VCR has been in Still/Slow mode for 5 minutes, it will stop automatically to protect the tape and
the video head from damage.
This feature allows you to play a tape over and over.
Select main menu by pressing [MENU].
1
Select "AUTO REPEAT" by pressing [PLAY] or
2
[STOP].
Begin auto repeat playback by pressing
3
[F.FWD] so that [ON] appears next to "AUTO
REPEAT".
• If the on-screen menu still remains, press
[COUNTER RESET/EXIT] to exit the menu.
• To cancel the Auto repeat mode, press [F.FWD] at
step [3] so that [OFF] appears next to "AUTO
REPEAT".
Search Functions
Picture Search
If you want to skip or repeat a scene during playback,
press [F.FWD] or [REW].
• Press it again and the VCR will now search in super
high speed. (in the LP/SLP modes only)
Index Search
An index mark will be assigned at the beginning of
each recordings you make. You may skip to a specific
marked point by following the steps below.
Press [SEARCH MODE] so that the Index
1
Search menu appears.
Enter the number of recordings
2
you wish to skip by pressing [PLAY] or [STOP]
within 30 seconds.
Press [F.FWD] or [REW] to start index search. If
3
you want to go in the forward direction, press
[F.FWD]. If you want to go in the reverse direction, press [REW].
• After index search, the VCR will play the tape automatically.
Time Search
This feature allows you to go to a specific point on a
tape by entering the exact amount of time you wish to
skip in order to reach the point.
Press [SEARCH MODE] twice so that the Time
1
Search menu appears.
Enter your desired time to skip
2
by pressing [PLAY] or [STOP] within 30 seconds.
Press [F.FWD] or [REW] to start time search. If
3
you want to go in the forward direction, press
[F.FWD]. If you want to go in the reverse direction, press [REW].
• After time search, the VCR will play the tape automatically.
INDEX SEARCH
03
TIME SEARCH
2 : 50
RECORDING FUNCTION
It may be unlawful to record copyrighted material without the consent of the copyright owner.
Accidental erasure prevention
To prevent accidental recording on a
recorded cassette, remove its record
safety tab.To record on it later, cover
the hole with cellophane tape.
Before recording, make sure:
• The desired channel is selected by pressing
[Number] on the remote control or the
[CHANNEL]. (If you connected the VCR to a
cable box or satellite box as in "VCR to TV
Connection" on page 3, select the VCR to channel 3
or 4 the same channel as the RF output channel of
the VCR. Then, select the channel you want to record
at the cable box or satellite box. In this case, you can
Y record and view the SAME channel. )
ONL
• There is a tape with its safety tab into the VCR.
• The desired recording speed is selected in SP(stan-
dard play) or SLP(super long play) mode by pressing
[SPEED] on the remote control.
• TV STEREO or SAP is selected.
Viewing and Recording the Same Program
Begin the recording by pressing [RECORD].
1
• To temporarily stop recording or resume it, press
[PAUSE]. After the VCR has been in Pause mode
for 5 minutes, it will stop automatically to protect
the tape and the video head from damage.
Press [STOP] when recording is completed.
2
IRT (Instant Recording Timer)
This feature allows you to set the recording length simply by pressing [REC/IRT] on the VCR.
Begin IRT by pressing [REC/IRT] on the VCR
1
repeatedly until the desired recording length
appears.
– 5 –EN
– 5 –EN
TIMER RECORDING
Select once, daily or weekly recording
Set the tape speed
Set the channel number
Set the end time
Set the start time
Set the date
Set the program number (1~8)
Press [PLAY] or [STOP] repeatedly for the desired channel number.
Then, press [F.FWD].
If you connected the VCR to a cable box or satellite box as in "Connect
VCR to TV" on page 3, select the VCR to channel 3 or 4 the same channel
as RF output channel of the VCR.
Then, select the channel you want to record at the cable box or satellite box.
Leave the cable box or satellite box on for timer recording.
Press [PLAY] or [STOP] repeatedly for the
desired
tape speed.
Then, press [F.FWD].
Program number which is not set up flashes.
Press [PLAY] or [STOP] repeatedly for the
desired program number.Then, press [F.FWD].
First, press [PLAY] or [STOP] for the month. Then, press [F.FWD].
Next, press [PLAY] or [STOP] for the day. Then, press [F.FWD].
First, press [PLAY] or [STOP] for the hour. Then, press [F.FWD].
Next, press [PLAY] or [STOP] for the minute. Then, press [F.FWD]
.
And then, press [PLAY] or [STOP] for AM or PM. Then, press [F.FWD]
.
Follow the instructions of "Set the start time" to set the end time.
For weekly:
Press [PLAY] or [STOP] to point to
"WEEKLY".
Then, press [F.FWD].
For daily (Monday~Friday):
Press [PLAY] or
[STOP] to point to "DAILY".
PROGRAM NUMBER 4
ONCE
DAILY
WEEKLY
ONE TIME PROGRAM
PROGRAM NUMBER 4
DATE 05/12 MON
START TIME 07:30 PM
END TIME 08:30 PM
CHANNEL 16
REC SPEED SP
SP
SLP
PROGRAM NUMBER 4
DATE - - / - START TIME - - : - - - END TIME - - : - - - CHANNEL - REC SPEED - -
For once:
Press [PLAY] or [STOP] to point to "ONCE".
• To go back one step, press [REW].
You may set the VCR to start recording while you are
away.You can set eight programs to record on specific
days, daily or weekly within a 1 year period.
Insert a tape with its safety tab into the VCR.
1
Select main menu by pressing [MENU].
2
Select "TIMER PROGRAMMING" by pressing
3
[PLAY] or [STOP]. Then, press [F.FWD].
• If you have not yet set the clock, "CLOCK SET"
appears. If so, continue with the step [3] in "CLOCK
SET UP" section. Then, set the timer recording.
Set the timer.
4
Hints for Timer Recording
• If there is a power failure or the VCR is unplugged for
more than 30 seconds, the clock setting and all timer
settings will be lost.
• If the tape runs out before the end time, the VCR will
switch to the Stop mode immediately, eject the tape
and the VCR power will be turned off. The TIMER
indicator will flash.
• If a tape is not in the VCR or does not have the safety
tab, the TIMER indicator flashes and timer recording
cannot be performed. Please insert a recordable
tape.
To Stop an Automatic Timer Program already started
Press [STOP/EJECT]
To Check, Correct, or Cancel an Automatic Timer Program
Turn the power on by pressing [POWER].
on the VCR.
1
Select main menu by pressing [MENU].
2
Select "TIMER PROGRAMMING" by pressing
3
[PLAY] or [STOP]. Then, press [F.FWD].
Select the program number which you want
4
to check by pressing [PLAY] or [STOP].The
details of the selected program appears on the
TV screen.
• Go to the digit you want to change by pressing
[F.FWD] or [REW]. Then, enter correct numbers by
pressing [PLAY] or [STOP].
• You may cancel the entire program by pressing
[REW] during the program number flashes.
Press [COUNTER RESET/EXIT] to exit.
5
Press [POWER] to return to timer stand-by
6
mode.
5
6
To set another program, repeat step [4]. To exit, press
[COUNTER RESET/EXIT].
Press [POWER] to set the timer. The TIMER indicator
on the VCR comes on.
NOT BE ACTIVATED UNLESS YOU TURN THE VCR
OFF.
TIMER RECORDING WILL
Counter Memory Function
Use this feature to memorize the beginning of recording start point.
Press [COUNTER RESET/EXIT]
1
on the remote control to reset
the counter.
Press [COUNTER MEMORY] on
2
the remote control so that “M”
appears on the TV screen.
Record the program.
REC
SPM0:00:00M0:00:00
3
After recording, press [STOP] then [REW].
4
• When “0:00:00” is reached, rewinding operation goes to
stop. And you can view the recording program.
• [COUNTER MEMORY] does not function if the Auto
repeat mode is set to [ON]. In this case, set the Auto
repeat mode to [OFF].
• To cancel the Counter memory mode, press [COUNTER
MEMORY] so that “M” disappears from the TV screen.
– 6 –EN
MTS Recording / Monitor Mode
Type of
broadcast
Hi-Fi audio track
(2-channel)
Normal audio
track
L+R
L+R
STEREO/SAP
Selection
L
L
R
R
Display on the
TV screen
Regular
(monaural audio)
Bilingual
broadcast
Stereo &
Bilingual
broadcast
Stereo
broadcast
-None-
STEREO
STEREO
SAP
SAP
-Invalid-
-Invalid-
TV STEREO*
SAP*
TV STEREO*
SAP*
L-channel R-channel
MonoMono
Mono
Main audio
program
Sub audio
program
Main audio
program
Sub audio
program
Main audio
program
Sub audio
program
Sub audio
program
Sub audio
program
Sub audio
program
* You must select the recording mode in TV STEREO or SAP before you record a broadcast.
STOP 12:00AM
CH 32
STEREO
SAP
SP 0:00:00 HIFI
1)
2)
ANT in
[TV set]
(Use for monitoring)
RF cable
(supplied)
[Playing VCR]
(another source)
Audio/Video cables
(not supplied)
IN
OUT
AUDIO
VIDEO
LEFT
RIGHT
[Recording VCR]
(this unit)
ANT
AUDIO
VIDEO
IN
OUT
OUT IN
OUT
L
R
IN
SPECIAL FEATURES
Copying a Video TapeMTS (Multi-Channel Television
You can make copies of video tapes made by friends or
relatives for your enjoyment.
Warning: Unauthorized recordings of copyrighted video
tapes may be an infringement of copyright laws.
Connect the recording VCR(this unit), the playing VCR
(another source) and your TV using the following diagram.
Insert a pre-recorded tape into the playing
1
VCR.
Insert a tape with its safety tab into the
2
recording VCR.
Press [SPEED] on the remote control of the
3
recording VCR to select the desired recording
speed (SP/SLP).
Select the “L1” or “L2”position on the record-
4
ing VCR. See page 3, under “Using
AUDIO/VIDEO Input Jacks”.
Press [REC/IRT] on the recording VCR.
5
Begin playback of the tape in the playing VCR.
6
• For best results during dubbing, use the VCR’s front
panel controls whenever possible. The remote control might affect the playing VCR’s operation.
• Always use video-quality shielded cables with RCAtype connectors. Standard audio cables are not recommended.
• You can use a video disc player, satellite receiver, or
other audio/video component with A/V outputs in
place of the playing VCR.
To Monitor the Recording
Turn on the TV and set the TV to channel 3. If
1
channel 3 is already occupied for broadcasting,
change the RF output to CH4, and change the TV
channel to CH4.
(See “RF Output Channel” on page 3 for the
detail.)
Press [VCR/TV] on the remote control of the
2
recording VCR so that the VCR indicator
comes on.
Sound) System
When you play a VHS tape, or
receive a broadcast on the VCR
tuner channel you are watching,
the status shown below will
appear when you press [DISPLAY] on the remote control.
When you record the MTS broadcast signal, you need
setting the MTS mode.
Press [MENU] and select "TV STEREO" or
1
"SAP" by pressing [PLAY] or [STOP].Then,
press [F.FWD] for fix mode. To exit, press
[COUNTER RESET/EXIT].
• Although a program may be broadcast in both
stereo and second audio, you must select the
Recording mode in TV STEREO or SAP before you
record a broadcast.
Press [MENU] and select "AUDIO OUT" by
2
pressing [PLAY] or [STOP].Then, press
[F.FWD]. Next, select "HIFI" or "MONO" by
pressing [PLAY] or [STOP].To exit, press
[COUNTER RESET/EXIT].
• While the VCR is set in HIFI stereo mode, HIFI
appears on the TV screen. While the VCR is set in
monaural (MONO) mode, HIFI disappears from the
TV screen.
Auto Rewind
When a tape has reached the end during recording,
playback, or fast-forward, the tape will automatically
rewind to the beginning. After rewinding finishes, the
VCR will eject the tape and turn itself to off.
• The VCR will not rewind the tape automatically during timer recording or One Touch Recording.
Real Time Tape Counter
• This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time will
not change during blank portions on the tape.)
• The indication will appear when the tape is rewound
further than “0:00:00” on the tape counter.
– 7 –EN
(
)
Supplied Accessories
TROUBLESHOOTING GUIDE
If you have followed the instructions contained in this manual and have difficulty in operating your VCR, locate the PROBLEM
in the left column below. Check the corresponding CORRECTIVE ACTION column to remedy the problem.
PROBLEMCORRECTIVE ACTION
No power.• Make sure the power plug is connected to an AC outlet.
Timer recording is impossible.• Make sure the timer recording is set correctly.
Cannot go into Record mode.• Make sure the tape has a safety tab. If needed, cover the hole with cellophane tape.
Playback picture is partially noisy. • Adjust tracking control for a better picture by pressing [CHANNEL] on the VCR.
Cannot view a tape but the• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING” .
audio is OK
No or poor playback picture.• Turn on the TV and set the TV to channel 3. If channel 3 is already occupied for broad-
TV programs cannot be seen• Re-check the ANT. IN and ANT. OUT connections. See page 3.
normally.
No VCR operation from the• Make sure the power plug is connected to an AC outlet.
infrared Remote Control.
.
• Make sure the power is turned on.
• Make sure the power is off.
• Make sure the VCR clock is set correctly.
• Make sure the VCR is not in the Menu mode.
casting, change the RF output to CH 4, and change the TV channel to CH4. (See “RF
Output Channel” on page 3 for the detail.)
• Fine tune your TV.
• Press [VCR/TV] on the remote control so that the VCR indicator on the VCR disappears.
• Check batteries in remote control.
SPECIFICATIONS
Operating temperature : 41°F~104°F (5°C~40°C)
Converter output :VHF Channel 3 or 4.
Power requirement :120V, 60Hz
Power consumption :14 Watts
Dimensions :W 14-1/4” (360mm)
H 3-5/8” (92mm)
D 8-1/2” (216mm)
Weight :4.0 lbs. (1.8 Kg.) (approx.)
• Designs and specifications are subject to change without notice and legal obligation.
• If there is a discrepancy between languages, the default language will be English.
Should your VCR become inoperative, do not try to correct
the problem by yourself. There are no user-serviceable parts
inside. Turn off, unplug the power plug, and please call our
help line at
1-800-448-2244,
to locate an Authorized Service Center.
Remote control
Two AA batteries
VT-RM795A (TJ16963)
MAINTENANCE
DECLARATION OF CONFORMITY
with FCC Rules for Electromagnetic Compatibility
This device complies with part 15 of FCC Rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference
that may cause undesired operation.
Responsible Party:HITACHI AMERICA, LTD.
Products: VIDEO CASSETTE RECORDER
Models: VT-FX795A
Trade Name: HITACHI
HOME ELECTRONICS DIVISION
1855 Dornoch Court, San Diego,
CA 92154-7255 U.S.A
Tel:619-661-0227
RF Cable
(5857952)
Cabinet CleaningServicing
• Wipe the front panel and other exterior surfaces of the VCR
with a soft cloth immersed in lukewarm water and wrung dry.
• Never use a solvent or alcohol. Do not spray insecticide liquid near the VCR. Such chemicals may cause damage and
discoloration to the exposed surfaces.
Auto Head Cleaning
• Automatically cleans video heads as you insert or remove a
cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted while
the TV program reception is clear. Dirt accumulated on the
video heads after long periods of use, or the usage of rental
or worn tapes can cause this problem. If a streaky or snowy
picture appears during playback, the video heads in your
VCR may need to be cleaned.
1. Please visit your local Audio/Video store and purchase a
good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem,
please call our help line at 1-800-448-2244, to locate an
Authorized Service Center.
NOTES:
• Remember to read the instructions included with the video
head cleaner before use.
• Clean video heads only when problems occur.
– 8 –EN
Ajuste el mes.
Ajuste el día.
Ajuste el año.
Ajuste el minuto.
Ajuste la
mañana (AM) o
la tarde (PM).
Ajuste la ora.
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
Pulse repetidamente [PLAY] o [STOP].
Luego, pulse [F.FWD].
Pulse repetidamente [PLAY] o [STOP].
CONTROLES DE FUNCIONAMIENTO Y FUNCIONES
AJUSTE DE RELOJ
MES DIAAÑO
03 17/LUN 2003
HORA MINUTO
05 : 40
AM/PM
PMPMAM
Panel frontal
1. Compartimiento del videocasete
2. Botón de avance rápido
3. Botón de reproducción
4. Botón de rebobinado
5. Botón de parada/expulsión
6. Botón de grabación con un toque
7. Indicadores
8. Sensor de control remoto
9. Botones de selección de canales
10. Botón de la alimentación
11. Terminal de entrada de audio
12. Terminal de entrada de vídeo
Indicadores
13. Indicador de alimentación
14. Indicador de videocasete introducido
15. Indicador de videograbadora
16. Indicador del grabación
17. Indicador de temporizador
18. Indicador del reloj y tarde
Panel trasero
19. Terminal de salida de audio
20. Terminal de entrada de audio
21. Terminal de entrada de antena
22. Terminal de salida de antena
23. Terminal de entrada de vídeo
24. Terminal de salida de vídeo
25. Cable de alimentación
Mando a distancia
1. Botón de la alimentación (POWER)
2. Botones de número (NUMBER)
3. Botón de menús (MENU)
4. Botón de visualizador (DISPLAY)
5. Botón de reproducción (PLAY)
6. Botón de rebobinado (REW)
7. Botón de grabación (REC)
8. Botón del modo de búsqueda (SEARCH MODE)
9. Botón de velocidad (TAPE SPEED)
10. Botón de pausa (PAUSE)
11. Botón de parada (STOP)
12. Botón de avance rápido (F.FWD)
13.
Botón de c.reposición/salida (COUNTER RESET/EXIT)
14. Botón (COUNTER MEMORY)
15. Botón de cámara lenta (SLOW)
16. Botones de selección de canales (CH)
17. Botón de expulsión (EJECT)
18. Botón de videograbadora/televisor (VCR/TV)
PREPARACIÓN DE CANALES
(La antena o la caja de televisión por cable
deberá estar conectada)
NOTA: Cuando utilice su nueva videograbadora por
primera vez, o en el caso de ser necesario después
de producirse un fallo en la alimentación, la
videograbadora se pondrá inicialmente en el modo
de preajuste cuando se pulse [POWER].
1. Encienda el televisor y ponga el televisor en el
canal 3.
2. Pulse [POWER] para encender la
videograbadora.
3. Seleccione "ENGLISH" , "FRANCAIS"(French) o "ESPAÑOL"
(Spanish) pulsando [PLAY] o
[STOP].Y luego pulse [F.FWD].
4. Pulse una vez [F.FWD].
El sintonizador explora y memoriza todos los
canales activos de su zona. Tras la exploración, el
sintonizador se detiene en el canal memorizado
más bajo.
PREPARACIÓN DEL RELOJ
1. Pulse [MENU] hasta que aparezca el menú princi-
pal. (Si el reloj no está puesto en hora y se pulsa
[MENU], el menú AJUSTE DE RELOJ aparece en
primer lugar. En este caso, siga el paso 3.)
2. Pulse [PLAY] o [STOP] para indicar a "AJUSTE DE
RELOJ". Luego, pulse [F.FWD].
3.
• Para volver atrás un paso, pulse
[REW].
4. Pulse [COUNTER RESET/EXIT] o [F.FWD] para
poner en funcionamiento el reloj.
– 9 –EN
MEMO
– 10 –EN
WARRANTY
– 11 –EN
WARRANTY
Printed in China
TJ16971 C Hitachi, Ltd. 2003
0VMN03630 / HD455UD ★★★★★
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.