Your Complete Guide
to Videocassette Viewing
and Recording
Using these quality features:
VHS hi-fidelity sound in playback
Automatic tape head cleaning
Up to 8 delayed recording programs
Auto tracking for improved picture in playback
Frequency synthesizer quartz tuner
Illuminated remote control for use with your VCR and TV
On-screen programming guide
Multi-channel TV sound (MTS)
Auto clock set feature
VCR Plus+* for easy timed recording
* VCR Plus+ and PlusCode are trademarks of Gemstar Development Corp. VCR
Plus+ system is manufactured under license from Gemstar Development Corporation.
Tape Navigation
Displaying Captions
HITACHI HOME HITACHI SALES HITACHI (HSC)
ELECTRONICS CORPORATION CANADA INC.
(AMERICA), INC. OF HAWAII, INC. 3300 Trans Canada Hwy.
3890 Steve Reynolds Blvd., 3219 Koapaka Street Pointe
Claire, Quebec
Norcross, GA 30093 Honolulu, HI 96819 H9R1B1, CANADA
Tel. 404-279-5600 Tel. 808-836-3621 Tel. 514-697-9150
TABLE OF CONTENTS............................................................................................................................2
FOR YOUR SAFETY.................................................................................................................................5
Read This First........................................................................................................................................7
IMPORTANT SAFEGUARDS ..................................................................................................................8
POWER SUPPLY: AC 120V, 60 Hz ONLY.
The POWER switch turns the VCR on and off, leaving the clock/timer unaffected. If the
unit is to be left unattended for a long period, it is recommended that the unit be
completely switched off and unplugged.
Illustrated below is the label on the back of your unit.
This symbol warns the user that uninsulated voltage within the unit may have
sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of
contact with any inside part of this unit.
This symbol alerts the user that important literature concerning the operation and
maintenance of this unit has been included. Therefore, it should be read carefully in order
to avoid any problems.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: Many television programs and films are copyrighted. In certain circumstances,
copyright law may apply to private in-home videotaping of copyrighted materials.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
5
FOR YOUR SAFETY
Caution to user: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
"Note to CATV system installer: This reminder is provided to call the CATV system
installer's attention to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as practical".
6
Read This First
Read This First
Thank you for buying a Hitachi product. You've chosen the best VCR for you, and we
want to help you make the most of your purchase. Please take time to become familiar
with this manual and how it is set up. Keep it handy for future reference, too.
To guide you, we've concluded:
"Must read" sections containing important cautions for your family's safety as well as
the basic facts you need to use the VCR. These sections are highlighted like this in the
table of contents:
Information on the advanced features of your Hitachi VCR. We hope you'll take time
to learn about these functions since we've designed them for you. But you can use the
VCR without reading these sections.
We want this manual to be a tool for you, so we provide two ways to find the information
you need:
A quick index to the basic functions of the VCR which you will use often (this page).
A detailed table of contents directing you to specific information quickly (page 4).
Get to know your VCR by using this manual, and get to know Hitachi. We appreciate
your business.
7
IMPORTANT SAFEGUARDS
IMPORTANT SAFEGUARDS
In addition to the careful attention devoted to quality standards in the manufacture of
your video product, safety is a major factor in the design of every instrument. But,
safety is your responsibility too.
This page lists important information that will help to assure your enjoyment and proper
use of a Video Cassette Recorder and accessory equipment. Please read it carefully
before operating your video product and keep it in a handy place for future reference.
INSTALLATION
1 Read and Follow Instructions -- All the safety and operating instructions should be
read before the video product is operated. Follow all operating and use instructions.
2 Retain Instruction -- The safety and operating instructions should be retained for
future reference.
3 Heed Warnings -- Comply with all warnings on the video product and in the
operating instructions.
4 Polarized Plug -- This video product is equipped with a polarized alternating-current
line plug (a plug having one blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. To prevent electric shock do not use this
polarized plug with an extension cord, receptacle or other outlet unless the blades can
be fully inserted without blade exposure. If you need an extension, use a polarized
cord.
5 Power Sources -- This video product should be operated only from the type of power
source indicated on the marking label. If you are not sure of the type of power supply to
your home, consult your video dealer or local power company. For video products
intended to operate from battery power, or other sources, refer to the operating
8
IMPORTANT SAFEGUARDS
instructions.
6 Overloading -- Do not overload wall outlets and extension cords as this can result in
a risk of fire or electric shock. Overloaded AC outlets and extension cords are
dangerous, and so are frayed power cords, damaged or cracked wire insulation and
broken plugs. They may result in shock or fire hazard. Periodically examine the cord
and have it replaced by your service technician if appearance indicates damage or
deteriorated insulation.
7 Power Cord Protection -- Power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience receptacles, and the point where they
exit from the appliance.
8 Ventilation -- Slots and openings in the cabinet are provided for ventilation to ensure
reliable operation of the video product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be blocked by
placing the video product on a bed, sofa, rug or other similar surface. This video
product should never be placed near or over a radiator or heat register. This video
product should not be placed in a built-in installation such as a bookcase or rack unless
proper ventilation is provided or the video product manufacturer's instructions have
been followed.
9 Attachments -- Do not use attachments unless recommended by the video product
manufacturer as they may cause hazards.
Caution: Maintain electrical safety. Power-line operated equipment or accessories
connected to this unit should bear the UL listing mark or CSA certification mark on the
accessory itself and should not have been modified so as to defeat the safety features.
This will help avoid any potential hazard from electric shock or fire. If in doubt, contact
qualified service personnel.
10 Water and Moisture -- Do not use this video product near water -- for example,
9
IMPORTANT SAFEGUARDS
near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a
swimming pool, and the like.
11 Accessories -- Do not place this video product on an unstable card, stand, tripod,
bracket or table. The video product may fall, causing serious injury to a child or adult,
and serious damage to the appliance. Use only with a cart, stand, tripod, bracket or
table recommended by the manufacturer, or sold with the video product. Any mounting
of the product should follow the manufacturer's instructions, and should use a mounting
accessory recommended by the manufacturer.
11A An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart combination to
overturn.
12 Outdoor Antenna Grounding -- If an outside antenna or cable system is
connected to the video product, be sure the antenna or cable system is grounded so as
to provide some protection against voltage surges and built-up static charges. Section
810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with
respect to proper grounding of the mast and supporting structure, grounding of the leadin wire to an antenna discharge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirements for the grounding
electrode. See example below:
EXAMPLE OF ANTENNA GROUNDING
13 Power Lines -- An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside antenna system, extreme care
should be taken to keep from touching or approaching such power lines or circuits as
contact with them might be fatal. Installing an outdoor antenna can be hazardous and
should be left to a professional antenna installer.
USE
14 Cleaning -- Unplug this video product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
15 Object and Liquid Entry -- Never push objects of any kind into this video product
through openings as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of any kind on the video
product.
10
IMPORTANT SAFEGUARDS
16 Lightning -- For added protection for this video product during a lightning storm, or
when it its left unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable-system. This will prevent damage to the
video product due to lightning and power-line surges.
SERVICE
17 Servicing -- Do not attempt to service this video product yourself as opening or
removing covers may expose you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
18 Conditions Requiring Service -- Unplug this video product from the wall outlet and
refer servicing to qualified service personnel under the following conditions.
a. When the power-supply cord or plug is damaged
b. If liquid has been spilled or objects have fallen into the video product.
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions. Improper
adjustment of o t her controls may result in damage and will often require extensive work
11
IMPORTANT SAFEGUARDS
by a qualified technician to restore the video product to its normal operation.
e. If the video product has been dropped or the cabinet has been damaged.
f. When the video product exhibits a distinct change in performance -- this indicates a
need for service.
19 Replacement Parts -- When replacement parts are required, have the service
technician verify that the replacements he uses have the same safety characteristics as
the original parts. Use of replacements specified by the video product manufacturer can
prevent fire, electric shock or other hazards
20 Safety Check -- Upon completion of any service or repairs to this video product, ask
the service technician to perform safety checks recommended by the manufacturer to
determine that the video product is in safe operating condition.
12
Getting Started
Getting Started
Relax. Using a VCR is very straightforw ard.
This sections explains how to hookup the VCR, quick tour of the controls, set up for
first-time operation using on-screen menus, and videocassette tapes.
Enjoy getting to know all about your Hitachi VCR. Let's get started.
Simple Hookups
1 Decide Where to Put Your VCR
Be sure your chosen location allows for proper ventilation, stability, and protection
from heat and moisture (see Important Safeguards).
Place the VCR near your TV but not on top of it. For convenience in using the remote
control, locate them no more than three feet apart.
If you have an external cable or antenna, place the TV and VCR where you have
ample cable to hook them up. If necessary, you can purchase a cable extension and
connector.
If you plan to route your VCR audio through your stereo speakers for better sound
reproduction, place the VCR near the stereo receiver, or have enough long audio cables
to make the connections. (But keep in mind that the electronic signal weakens the
further it has to travel.)
2 Decide Which Hookup Method to Use
To make your VCR function, you'll deal with two basic hookups:
1. The audio and video signal: If all you want to do is view a prerecorded videotape on
the VCR, this three-line hookup is the only one you need.
2. The radio frequency (RF) signal from a cable or antenna: Make this hookup if you
also want to record programs, or if you have no audio/video connectors on your TV.
We will show you the simplest hookups first and then present several variations to suit
specific needs. Be aware that you may need to pur chase addi tional connector s to make
the desired hookup. These are available at video stores and electronic hardware
stores.
Choose which hookup method to use based on:
Your TV's capabilities
The type of antenna or cable system you have (for cable box hookup, see Advanced
Operations)
Any other devices you want to include in the system (stereo, second VCR, etc.)
We will guide you through the process. But first, turn the TV and the VCR around so
13
Getting Started
you are looking at their backs. Note the various input and output receptacles, their
shapes, and how they are labeled. Then read through the rest of this hookup section
before proceeding to an actual hookup.
DO NOT TURN ON THE POWER YET. FOR YOUR SAFETY, LEAVE YOUR TV AND
VCR UNPLUGGED WHILE HOOKING THEM UP.
3 Hook up the Audio/Video Signal
If your TV is a fairly recent model, you probably have both audio and video jacks. Look
on the back of your TV for three jacks--possibly color-coded yellow, white and red.
They will be labeled something like IN (L and R), AUDIO IN, or VIDEO IN. (If you are
not sure, look at the back of your VCR-- you will see two sets of these jacks.)
If you have no jacks like these on your TV, skip this step and proceed to Step 4.
TV with Audio and Video Jacks
If you do find all three jacks on your TV, you need to purchase a three-line audio/video
cable with bell (RCA) connectors, like this:
If you find a video jack and only one audio jack, your TV is probably monaural. You can
purchase a two-line audio/video cable, but the three-line is handy in case you get a
stereo TV later.
Connect the yellow VIDEO OUT jack on the VCR to the VIDEO IN jack on the TV.
This direct video input will give you the best picture. It will also let you play videos in a
"picture in picture" feature, if your TV has it.
Then connect the AUDIO OUT jacks (red and white) on the VCR to the AUDIO IN
jacks on the TV (left to left, right to right).
This audio hookup will give you better sound than the RF signal hookup, because the
electronic signal won't have to go through a conversion process.
Plus your VCR has a stereo decoder, which your TV might not. For big speaker sound,
you can also use these jacks to connect the VCR to your stereo system (page 74).
Capabilities: The audio and video signal connections are all you need to play back a
prerecorded tape. If you do not intend to record on your VCR from your antenna/cable,
then you're all hooked up now. Otherwise, continue with Step 4, which will let you
record off TV channels.
14
Getting Started
4 Hook up the RF Signal
Look at the back of your TV for a connector that looks like one of these, and follow the
corresponding hookup option. If you have any sort of cable box, see the hookup
options in Advanced Operations (page 71).
Simple Antenna/Cable 75 Ohm Hookup
This is an easy hookup that you can use if your cable or antenna has a 75 ohm round
wire connector. You will need the 75 ohm cable supplied with your VCR. It looks like
this:
If you have been watching the TV in your home before getting the VCR, you will already
have a round wire attached to your TV. Otherwise, look for a cable connection coming
in through the wall from outside. (If you find this connection, remember to call your local
cable company to start the service.)
1. If still hooked up to your TV, unscrew the round wire from the 75 ohm connector on
your television. Otherwise, take the wire that comes in from the wall.
2. Screw this round wire into the IN FROM ANT jack on the back of your VCR.
3. Using the 75 ohm cable supplied with your VCR, slide on either end to the OUT TO
TV jack on the back of the VCR.
4. Connect the other end of the same cable onto the 75 ohm antenna input on your TV
(where you first disconnected the TV in step 1.)
15
Getting Started
Capabilities: With this hookup, you should now be able to perform all the basic functions
provided by this equipment.
External or Internal 300 Ohm Antenna
If you have either an external or internal (rabbit ears) antenna rather than cable, you
may have 300 ohm connectors like these.
In this case, you will need special adapters to make the 75 ohm round wire connection
shown below. (You may already have one on your TV.)
1. Remove the antenna line from the back of your TV if it is already connected there, or
take it from where it comes in on the wall.
2. Considering the three pictures below, determine which adapter you will need to hook
it into your VCR.
If you have Use this adapter
Single 300 ohm flat wire
16
Getting Started
Separate UHF and VHF
antenna wires, both 300 ohm flat wire
300 ohm flat UHF and 75 ohm
round VHF
If you have "rabbit ears" (an antenna on top of your TV), you will need an additional
adapter and 75 ohm extension to make your leads reach from the antenna to the VCR.
This connection will work only if you have a strong, clear picture on the TV, indicating a
strong signal. Connect the antenna to the adapter, and use the cable extension to go
from the adapter to the VCR. Use the supplied 75 ohm cable to connect the VCR to the
TV.
Now continue with the hookup:
1. Using whichever adapter you have fit your antenna with, attach that connector to the
IN FROM ANT jack on the back of the VCR.
2. Using the 75 ohm cable supplied with your VCR, connect either end to the OUT TO
TV jack on the back of the VCR.
3. Use a second adapter to attach the other end of the 75 ohm connector back into the
TV (where you first disconnected the antenna).
Capabilities: With this hookup, you should now be able to perform all basic functions
17
Getting Started
provided by this equipment.
5 Attach the TV and VCR to the Power Supply
Plug in the TV and VCR power cords to the wall outlet or an appropriate extension cord
or surge protector. See Important Safeguards for further precautions (page 6).
6 Install Batteries in the Remote Control
The remote control requires two fresh "AA" batteries. On the back of the remote, a
plastic cover slides off in the direction shown by the arrow. Remove this cover and
install the batteries, matching the plus end of each battery with the plus mark on the
remote.
7 Set the RF or Video Channel Switch
When the VCR is on, its video signal can come into your TV on either channel 3 or
channel 4. You need to select the appropriate channel.
Turn the power on to both the TV and the VCR, and look for a switch on the back of
the VCR. Set the switch to 3 or 4, whichever is not a commercial channel in your area.
Your basic hookup is now complete. When you're ready to try hooking up a second
VCR or a video camera for a complete home entertainment system, see Advanced
Operations.
Now turn the TV and VCR back around facing you and begin your quick tour of the
controls (page 15).
18
Getting Started (Controls)
Getting Started (Controls)
Quick Tour of the Controls
Study these pictures carefully to learn about the buttons and controls that you'll need for
everyday operation. Various controls are explained throughout this manual as they are
needed, but now is a good time to get familiar with their locations.
Most of the time, you'll be directing the VC R from the remote contr ol, but there ar e some
controls on the VCR that will come in handy too.
When you're familiar with these basic controls, proceed to Initial Setup (page 20). We'll
show you how to program your local channels and set the clock to make your VCR fully
functional.
How the Remote Control Works
Pressing a button on the remote control transmits an invisible beam of light (infrared) to
a receiver at the right front of the VCR.
When using the remote, aim the front end toward the VCR and make sure nothi ng - - such
as a coffee table or your dog--is blocking the path of the infrared beam.
About the Illuminated Buttons
Try pressing the remote control's white buttons one at a time. As you press, one of the
three device buttons lights up - VCR, CAM, or TV. This helps you keep track of which
device you are controlling at the moment.
19
Getting Started (Controls)
Remote Control Buttons
Remote Control Illustration
POWER Turns the VCR on and off.
GUIDE Brings up an on-screen setup and programming guide, the Easy Guide System.
VCR/TV Switches between viewing through the VCR and not viewing through the VCR.
CLEAR Used in on-screen programming and indexing.
DISPLAY Used in on-screen programming and indexing.
VOLUME Increase or decrease the audio volume.
MUTE Turns off the audio until you press MUTE again.
REC Starts recording on the station the VCR is set to.
REW Rewinds the videotape.
PLAY Starts playing a loaded videocassette.
PAUSE Temporarily stops the cassette from recording or playing. Press PAUSE again
(or PLAY) to resume .
LIGHT Illuminates key function buttons for a few seconds.
SHUTTLE DIAL Controls the videocassette's forward and reverse motion with one
convenient dial.
JOG DIAL Moves the tape forward one frame at a time.
CC Used to display captions on the screen.
0 to 9 Number buttons used in on-screen programming. Can also be used to change
channels. (Simply press 2 or 3 digits for the channel you want--such as 0 and 6 for
channel 6, or 100/ENT and 2 and 4 for channel 124.)
AVX Used for recording from an auxiliary input such as a stereo system.
MENU Used to display the Tape Navigation directory.
Select
/ Used to select the type of tape and program using Tape Navigation.
VCR, CAM (camcorder)*, TV Device buttons let you set the remote to contr ol one of the
three devices.
CHANNEL Top button switches to next higher channel, bottom button switches to the
next lower channel. For these to operate, you must have preset your channels.
LAST CHANNEL Switches to the TV channel you watched previously during the
current viewing session.
F.FWD Fast forwards the videotape.
20
Getting Started (Controls)
STOP Stops a videocassette from playing, recording, pausing, rewinding--or anything it
is doing.
* Refer to the camcorder's instruction manual for its operation.
When the Remote Doesn't Work Right
Check out these possibilities:
Low Battery
If the remote is not working even at close range, try putting in two fresh AA batteries.
When replacing the batteries, remove the old batteries and press the POWER button
on the remote and hold it for about 10 seconds, then insert two fresh batteries.
Objects in the Way
There may be objects between the remote and the VCR--for instance, a stack of books
on the coffee table, your 2-year-old child, the dog. Hold the remote so that it points at
the VCR with nothing in the way.
If You Just Want to Watch TV
For normal TV viewing, you do not need to disconnect the VCR. When the TV and VCR
are already on, press POWER on the remote control. The VCR will shut off, but the TV
will stay on.
If you are recording on the VCR but want to watch a different channel on the TV, press
the VCR/TV button to switch back and forth between the TV channel and the recording
channel.
VCR Controls
Front Panel Controls Illustration
POWER Turns VCR power on and off.
STOP/EJECT Cancels any videotape action, and when pressed a second time, ejects
tape.
PLAY Play the loaded videotape.
DISPLAY Shows time, channel, and status indicators.
CHANNEL Up and down arrows for selecting channels.
REC/IRT To begin recording.
SHUTTLE Controls the videocassette's forward and reverse motion with one
convenient dial.
Select / Used to select the type of tape and program using Tape Navigation
21
Getting Started (Controls)
MENU Used to display the Tape Navigation directory.
Display Indicators
Watch for these signs and symbols that let you know that the VCR is responding to your
instructions.
Meet Your On-Screen Guide
Your Hitachi VCR has as a special feature called the Easy Guide System. This feature
guides you through simple setup and programming tasks right on the TV screen.
With the TV and VCR turned on, press GUIDE on the remo te control. You will see this
screen:
Now, you will do most of your programming and setup by pressing numbers on the
remote control which correspond to options presented in this and other on-screen
menus. Instructions are easy to follow, and blinking spaces on the screen will show you
where your input is needed.
When you want to leave the Easy Guide System, simply press GUIDE several times.
This will back you out to the normal TV viewing screen.
If you don't press any button for a while, the VCR will switch you back to an earlier
screen or to regular TV viewing.
22
Getting Started (Initial Setup)
Getting Started (Initial Setup)
Setup for First-Time Operation
Before you use your VCR to watch or record from your TV, you need to "tell" the VCR
whether your TV uses cable or antenna input and let it program itself to receive your
TV's channels. It's also a good idea to set the clock so you can do timed recording
later. With your TV and VCR hooked up, turn them both on and follow these steps
using the remote control.
Initial Setup Options
Press GUIDE, then press 5 to bring up the Initial Setup screen.
The screen shows the default settings on your VCR. The default settings are the ones
that are preset at the factory.
Look at each item to see if it matches your own setup:
To change a setting, press the button that has the same number as that item. This
will cycle you through several options.
When everything is set up as you want, press GUIDE again to back out of the Easy
Guide System.
If you do not use the cable box, you need to set items 1 and 8 the first time you set up
your VCR. If you receive all channels from the cable box, you need to set item 1 and
item 7 the first time you set your VCR (See page 48). The rest of the items can be set
later as needed.
Here is what the options mean:
1 CHANNEL
Press 1 to select the type of receiving setup you have:
23
Getting Started (Initial Setup)
<ANT> Internal or external antenna
<CATV1> Ordinary cable
<CATV2> Alternate cable (if CATV1 doesn't give you the channels you expect)
2 MOVIE
Press 2 to select whether you want prerecorded movies (safety tab removed) to play
automatically when loaded, and then rewind, eject and turn off the power when done.
Options are <ON> and <OFF>.
3 HIFI/LINEAR
Press 3 to control how the audio signal is processed by the VCR. Options are <HIFI>
and <LINEAR>.
4 STEREO/MONO
Press 4 to control how the audio signal is recorded and sent to the TV. Options are
<STEREO> and <MONO>.
5 SAP
Press 5 when you are ready to record a second audio program. Options are <OFF>
and <ON>.
7 CABLE BOX SET
Press 7 to set up your cable box if you receive all channels through a cable box.
8 AUTO CHANNEL SET
Press 7 to automatically program the VCR to receive all the channels that come in on
your antenna or cable.
9 ADD/ERASE CHANNEL
Press 8 to bring up a screen that lets you add new channels or limit the channels to the
ones you most often watch.
Note: Option 7 CABLE BOX SET is not enabled unless CATV 1 or CATV 2 has been
selected in option 1 CHANNEL setting.
Setting the Clock
This is easy to do and important for your later timed recordings.
You'll need to set the clock when first hooking up your VCR, and any time the power
goes out more than 1 hour.
When you first plug in the VCR or after a power outage, the clock display will read "--:-".
Auto Clock Set Function
This function sets the VCR's clock automatically when the VCR is tuned to a station
which transmits a time signal together with TV programs.
It also automatically sets the time differences between various time zones and sets the
24
Getting Started (Initial Setup)
time during Daylight Savings Time (DST). The auto clock set function operates each
time the VCR is turned off.
Some broadcast stations may not transmit a time signal. The auto clock set function
does not operate when the VCR is tuned to a station which does not transmit a time
signal. In this case, set the clock manually (See page 25).
When the clock is set automatically, the displayed time may drift from the current time
by up to one minute.
Setting the Clock with the Auto Clock Set Function
When the VCR is hooked up via an antenna or cable (no cable box):
1. Press POWER to turn the VCR power off.
When the VCR is turned off, press POWER to turn the power on, then press it again to
turn the power off.
The set time appears in the VCR display to show that the current time has been set.
It may take about five minutes for auto clock setting.
If the clock is not set after about five minutes have elapsed, press GUIDE then set the
clock manually (See page 25).
When the VCR power is recovered after a power failure of more than one hour, the
clock can be set automatically from the "--:--" indication.
If the displayed time drifts from the current time by more than one hour, select your
correct time zone and set the DST (See page 24).
When the VCR is hooked up via a cable box:
Before you begin:
Set up your cable box (See page 48).
1. Press GUIDE, then press 6 to bring up the CLOCK SET screen.
2. Check that item 1 is specified "CLOCK SET: AUTO".
If "CLOCK SET: MANUAL" is displayed, press 1 to switch it to "CLOCK SET: AUTO".
3. Press 2. The following screen appears to show that the clock is being set.
Since the VCR is searching for a broadcast station that transmits a time signal, the
channel indication on the cable box changes automatically.
25
Getting Started (Initial Setup)
4. The screen shown in step 3 above changes to a TV picture and the time appears in
the VCR's display.
It may take about five minutes for auto clock setting.
If the clock is not set after about five minutes have elapsed, press GUIDE then set the
clock manually (See page 25).
If the displayed time drifts from the current time by more than one hour, select your
correct time zone and set the DST (See page 24).
What to do if the displayed time drifts from the current time by more than one
hour
1. Press GUIDE, then press 6 to bring up the CLOCK SET screen. Check that item 1 is
specified "CLOCK SET: AUTO". Press 3 to bring up the TIME ZONE SETTING screen.
2. Press one of button 1-7 to select your local time zone.
1
3. Press GUIDE to bring up the CLOCK SET screen.
Press 4 to bring up the DST SETTING screen.
4. Choose one of the following options:
Press 1 to specify DST SETTING ON. The time advanced from the Standard Time by
one hour is displayed from the first Sunday of April through the last Sunday of October.
Press 2 to specify DST SETTING OFF. The Standard Time is displayed throughout the
year.
Press 3 to specify DST SETTING AUTO. The DST is set automatically.
If the displayed time drifts from the current time even after steps 1-5 have been
performed, reset the DST.
26
Loading...
+ 59 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.