Hitachi VT-F462A User Manual

FEATURES

HITACHI

Instruction Manual

Video Deck

VT-F462A

Hitachi Home Electronics (America), Inc.

For information concerning repairs, operation or technical assistance, please contact the Service Department of your nearest Regional Office.

Eastern Regional Office

1290 Wall Street West, Lyndhurst, New Jersey 07071 Tel. 201-935-8980

Mid-Western Regional Office

1400 Morse Ave., Elk Grove Village, Ill. 60007 Tel. 708-593-1550

Southern Regional Office

3890 Steve Reynolds Blvd., Norcross, GA 30093 Tel. 404-279-5600

Western Regional Office

401 West Artesia Boulevard, Compton, California 90220

HITACHI SALES CORPORATION OF HAWAII, INC.

3219 Koapaka Street, Honolulu, Hawaii 96819 Tel. 808-836-3621

HITACHI (HSC) CANADA INC.

3300 Trans Canada Highway, Pointe Claire, Quebec, H9R 1B1, CANADA Tel. 514-697-9150

E72118 P4706886 ©Hitachi, Ltd. 1992 Printed in Japan KF-N(N)

FEATURES

FOR YOUR SAFETY .....................................................................................................................................5

IMPORTANT SAFEGUARDS .........................................................................................................................7

...................................................................................................................................................3

FEATURES

CONTROLS AND FEATURES......................................................................................................................11

USING THE REMOTE CONTROL UNIT....................................................................................................18

INSTALLATION INTRODUCTION & ANTENNA SYSTEM .............................................................................19

INTRODUCTION .....................................................................................................................................19

CABLE SYSTEMS ...................................................................................................................................19

Rabbit ear antenna ..................................................................................................................................19

INSTALLATION CABLE SYSTEM................................................................................................................20

CABLE SYSTEM INFORM AT IO N.............................................................................................................20

ADDITIONAL INFORMATION...................................................................................................................20

CABLE SYSTEM VCR OPERAT IO N.........................................................................................................22

VIDEO CHANNEL SETTING ........................................................................................................................24

NORMAL TV VIEWING................................................................................................................................24

SETTIN G TH E C L O C K................................................................................................................................25

CHANNEL TUNING .....................................................................................................................................29

VCR FUNCTION SETTING..........................................................................................................................33

CONNECTION WITH A/V TV........................................................................................................................37

CASSETTE TAPES .....................................................................................................................................38

RECORDING TV PROGRAMS.....................................................................................................................39

INSTANT RECORDING ...............................................................................................................................42

PLAYBACK .................................................................................................................................................43

PLAYBACK USING SHUTTLE RING ............................................................................................................47

VCR Plus + FEATURE .................................................................................................................................48

VCR Plus+ SET UP FOR CONNECTION A 3 .........................................................................................51

VCR Plus+ SET UP FOR CONNECTION B...................................................................................................55

VCR Plus+ SET UP FOR CONNECTION C...................................................................................................56

VCR Plus+ RECORDING .............................................................................................................................58

TIMER RECORDING ...................................................................................................................................61

RECALLING THE PROGRAM ......................................................................................................................66

CLEARING ("ERASING") INFORMATION FROM A PROGRAM 3 ...............................................................67

PROGRAM PRIORITY.................................................................................................................................68

RECORDING FROM ANOTHER VCR...........................................................................................................69

RECORDING FROM A VIDEO CAMERA/RECORDER..................................................................................69

USING AS AN AUDIO DECK 6 ...........................................................................................................70

AUDIO DUBBING ........................................................................................................................................72

VIDEO DUBBING ........................................................................................................................................73

EASY EDIT BY USING OPTIONAL SYNCHRO EDIT CABLE.........................................................................73

PROGRAM EASY EDIT ...............................................................................................................................74

HOW TO OPERATE YOUR TV OR CABLE CONVERTER BY USING THE REMOTE CONTROL UNIT ...........77

HEAD CLEANING........................................................................................................................................79

PERIODIC MAINTENANCE.......................................................................................................................... 80

PROBLEM GUIDE....................................................................................................................................... 81

SPECIFICATIONS .......................................................................................................................................83

ACCESSORIES PARTS NUMBERS (For U.S.A. only) ...................................................................................84

Please read this instruction manual carefully before use and refer to it if any difficulties arise.

FEATURES

• VCR Plus+* programming feature

• VHS Hi-Fi stereo system

• Auto head cleaning system

• Setting 8 programs/1 year is possible with built-in programmable timer

• Cable-compatible frequency synthesizer quartz tuner

• Auto tracking

• Illuminated remote control for use in common by TV/VCR/Cable Converter

• Multichannel Television Sound (MTS) is receivable

• Easy guide system feature

• High speed rewind (2.5 minutes with T-120 tape) * VCR Plus+ is trademark of Gemstar Development Corporation.

EASY GUIDE SYSTEM FEATURE

This feature displays an outline of VCR operation procedure (playback, recording, clock setting, etc.) in 3 languages on the TV screen to guide you when operating the VCR. Connect the VCR and TV by the procedure shown on pages 11 - 17, and then perform the following.

1. Turn on TV and VCR.

2. Set the TV to channel 3 (or 4).

3. Press GUIDE button on the remote control unit.

HELLO I AM HITACHI'S EASY GUIDE SYSTEM

SELECT LANGUAGE

1 ENGLISH

2 FRANCAIS 3 ESPANOL

*TO START PRESS GUIDE

4. Select the language by pressing one of buttons "1" ~ "3" and then press the GUIDE button. "1" for English "2" for French "3" for spanish

SELECT NUMBER 1 TO 7 1 VCR PLUS RECORDING 2 DELAYED RECORDING 3 PROGRAM REVIEW

4 INITIAL SETUP 5 CLOCK SET 6 VCR PLUS SETUP 7 PROBLEM GUIDE *TO END PRESS GUIDE

5. Press "1" through "7" on the remote control unit. For example, press "5" for clock setting.

FEATURES

CLOCK SET

TIME --:- MONTH/DAY/YEAR

DATE --/--/- FILL IN BLINKING SPACE *TO END PRESS GUIDE

6. Press "GUIDE" to return to "original menu".

FOR YOUR SAFETY

Power supply: AC 120V 60 Hz only The POWER switch switches the VCR on and off, leaving the clock/timer unaffected. If the unit is to be left unattended for a long period, it is recommended that the unit be completely switched off and the plug removed. Illustrated below is the label on the back of your unit.

This symbol warns the user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: Many television programs and films are copyrighted. In certain circumstances, copyright law may apply to private in-home videotaping of copyrighted materials.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Moisture condensation

If you pour cold liquid into a glass, water vapor in the air will condense on the surface of the glass. This is moisture condensation. Moisture condensation on the head drum, one of the most crucial parts of the unit, will cause damage to the tape. When the VCR is exposed to a rapid temperature change from cold to warm, some condensation will occur. Under this condition, connect the power cord to the AC line, press POWER button on and allow at least two hours for the VCR to dry out.

FOR YOUR SAFETY

Caution for users living in an area with frequent electrical storms

Your VCR and TV may be damaged by power surges, or during electrical storms if they are connected to a cable systems/outside antenna, or they are plugged into an AC outlet. The use of surge protection devices at the antenna and AC inputs to the VCR and television will decrease the likelihood of damage from lightning surges in the power line or antenna/cable system. Two surge suppressor models are available from Hitachi Parts Distributers for U.S.A. only. Model COMBO #1 provides one protected AC receptacle and a set of in/out cable/antenna protection ports. Model COMBO #2 offers four protected AC receptacles, a six foot line cord, master rocker switch and a set of in/out cable/antenna protection ports.

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference regulations of the Canadian Department of Communications.

IMPORTANT SAFEGUARDS

In addition to the careful attention devoted to quality standards in the manufacture of your video product, safety is a major factor in the design of every instrument. But, safety is your responsibility too. This page lists important information that will help to assure your enjoyment and proper use of a Video Cassette Recorder and accessory equipment. Please read it carefully before operating your video product and keep it in a handy place for future reference.

INSTALLATION

1 Read and Follow Instructions -- All the safety and operating instructions should be read before the

video product is operated. Follow all operating and use instructions.

2 Retain Instruction -- The safety and operating instructions should be retained for future reference. 3 Heed Warnings -- Comply with all warnings on the video product and in the operating instructions. 4 Polarized Plug -- This video product is equipped with a polarized alternating current line plug (a plug

having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. To prevent electric shock do not use this polarized plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted without blade exposure. If you need an extension, use a polarized cord.

5 Power Sources -- This video product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your video dealer or local power company. For video products intended to operate from battery power, or other sources, refer to the operating instructions. 6 Overloading -- Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. Overloaded AC outlets and extension cords are dangerous, and so are frayed power cords, damaged or cracked wire insulation and broken plugs. They may result in a shock or fire hazard. Periodically examine the cord and have it replaced by your service technician if appearance indicates damage or deteriorated insulation.

7 Power Cord Protection -- Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

IMPORTANT SAFEGUARDS

8 Ventilation -- Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the video product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the video product on a bed, sofa, rug or other similar surface. This video product should never be placed near or over a radiator or heat register. This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the video product manufacturer's instructions have been followed.

9 Attachments -- Do not use attachments unless recommended by the video product manufacturer as they may cause hazards.

Caution: Maintain electrical safety. Powerline operated equipment or accessories connected to this unit should bear the UL listing mark or CSA certification mark on the accessory itself and should not have been modified so as to defeat the safety features. This will help avoid any potential hazard from electric shock or fire. If in doubt, contact qualified service personnel.

10 Water and Moisture -- Do not use this video product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 11 Accessories -- Do not place this video product on an unstable card, stand, tripod, bracket or table. The video product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket or table recommended by the manufacturer, or sold with the video product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. 11A An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

IMPORTANT SAFEGUARDS

IMPORTANT SAFEGUARDS (cont.) pg. 5

12 Outdoor Antenna Grounding -- If an outside antenna or cable system is connected to the video

product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antennadischarge unit, connection to grounding electrodes, and requirements for the grounding electrode. See example below.

EXAMPLE OF ANTENNA GROUNDING

13 Power Lines -- An outside antenna system should not be located in the vicinity of overhead power

lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching or approaching such power lines or circuits as contact with them might be fatal. Installing an outdoor antenna can be hazardous and should be left to a professional antenna installer.

USE

14 Cleaning -- Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners

or aerosol cleaners. Use a damp cloth for cleaning. 15 Object and Liquid Entry -- Never push objects of any kind into this video product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product.

16 Lightning -- For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable-system. This will prevent damage to the video product due to lightning and power-line surges.

IMPORTANT SAFEGUARDS

17 Servicing -- Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. 18 Conditions Requiring Service -- Unplug this video product from the wall outlet and refer servicing to qualified service personnel under the following conditions. a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the video product. c. If the video product has been exposed to rain or water. d. If the video product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions. Improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation. e. If the video product has been dropped or the cabinet has been damaged. f. When the video product exhibits a distinct change in performance - this indicates a need for service. 19 Replacement Parts -- When replacement parts are required, have the service technician verify that the replacements he uses have the same safety characteristics as the original parts. Use of replacements specified by the video product manufacturer can prevent fire, electric shock or other hazards. 20 Safety Check -- Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks recommended by the manufacturer to determine that the video product is in safe operating condition.

SERVICE

CONTROLS AND FEATURES

1. VIDEO IN

Receives video signal from a video camera or another VCR.

2. AUDIO IN

Receive audio signals from a stereo system or another VCR. AUDIO IN (L) handles the left-channel stereo sound or monaural sound. If you connect an audio source to only AUDIO IN (L), the same sound is recorded on Hi-Fi tracks (L) and (R) in monaural.

3. EDIT IN/OUT JACK

This jack allows you to connect selected models of VCR's and video camera using optional synchro edit cables. Refer to page 49 for details.

4. CASSETTE COMPARTMENT

Insert a cassette in through a door, and loading will be completed automatically.

CONTROLS AND FEATURES

Note: Power is turned on automatically when the cassette is loaded.

5. AUDIO DUBBING BUTTON

Turns the audio dubbing features on. To turn this feature off, press STOP button. See page 47 for details.

6. VIDEO DUBBING BUTTON

Turns the video dubbing features on. To turn this feature off, press STOP button. See page 48 for details.

7. CHANNEL SELECT BUTTONS

Select the channels you wish to view or to record by pressing these buttons. And you can also select L (line)* by pressing these buttons to record or watch the program input at the VIDEO IN and AUDIO IN. (*One channel position either higher or lower outside the range of your preset channels.)

8. REC/IRT BUTTON

Press to start recording.

9. PAUSE/STILL BUTTON

Press to pause during recording or playback.

10. INFRARED RA Y RECEIVING SECTION

Receives the infrared ray from remote control unit.

11. SHUTTLE RING

During play, turn this ring to speed up or slow down playback speed at a smooth variable rate for everything from slow motion to forward search. Removing the hand from the ring restores a normal play.

12. PLAY/STILL BUTTON

Press in the stop mode to set the VCR to the playback mode. Press during play to set the VCR to the still play mode. Press again to restore normal play.

13. POWER BUTTON

Turn system power on and off.

14. STOP/EJECT BUTTON

If this button is pressed, while the set is operating, the running of tape stops and all operating modes are cancelled (except for timer recording). The cassette is ejected, when this button is pressed again in STOP mode.

CONTROLS AND FEATURES

Note: Power may be on or off when removing the cassette.

CONTROLS AND FEATURES (cont.) pg. 7

15. CLOCK DISPLAY

Shows the clock and tape counter.

16. STEREO INDICATOR

Lights when receiving a stereo broadcast.

17. TIMER INDICATOR

Will light when turning power off after programming.

18. LEVEL METER

Shows the input level of each audio channel during recording and the recorded levels during playback. However, when a tape on which normal (linear) sound was recorded is played back, the "L" and "R" indications disappear from the display.

19. CHANNEL INDICATOR

Normally shows the channel number. "L" lights when you select the LINE position by pressing the AVX button or CHANNEL select button. LINE position is used to record or watch the program input at the VIDEO IN and AUDIO IN.

20. VCR MODE INDICATOR

•

• PAUSE button is pressed again.

•

21. SAP INDICATOR

Some TV stations transmit a "Second Audio Program" (SAP). The SAP is normally used for a second language. This indicator lights when the VCR is tuned to SAP broadcast.

22.

Appears when the VCR is turned on or the VCR is in the playback mode.

23. TAPE SPEED INDICATORS

24. TAPE-IN INDICATOR

Lights when cassette is loaded in the compartment.

25. VIDEO IN

appears during recording.

appears during the rewind mode.

appears during the fast-forward mode.

appears during the playback.

appears when the PAUSE button is pressed during record or play mode and disappears when the

appears during slow-motion play using the shuttle ring.

INDICATOR

CONTROLS AND FEATURES

Receives video signal from a video camera or another VCR.

26. AUDIO IN

Receives audio signals from a stereo system or another VCR. AUDIO IN (L) handles the left-channel stereo sound or monaural sound. If you connect an audio source to only AUDIO IN (L), the same sound is recorded on Hi-Fi tracks (L) and (R) in monaural.

27. ANTENNA OUTPUT

Connect this terminal to the antenna terminal on the back of the TV.

28. RF CONVERTER SWITCH

Set this switch to whichever channel (CH3 or CH4) is unused in your area.

29. ANTENNA INPUT

Connect the UHF and/or VHF antenna to this terminal.

30. AUDIO OUT

For a connection to a monitor or another VCR.

31. VIDEO OUT

For connection to monitor TV.

CONTROLS AND FEATURES

CONTROLS AND FEATURES (cont.) pg. 8

32. SIGNAL TRANSMISSION WINDOW

Transmits an invisible light beam (infrared) from the remote control unit to the VCR.

33. TV BUTTON

First press this button when operating your TV with this remote control, and then press the button which corresponds to the function you want.

34. EJECT BUTTON

When this button is pressed in modes other than recording, the tape stops, and the cassette is ejected.

35. CATV BUTTON

First press this button when operating your Cable Converter with this remote control, and then press the button which corresponds to the function you want.

36. VCR 2 BUTTON

Press this button when using another Hitachi VCR and operating the remote control provided to control the two VCRs.

37. LAST CH BUTTON

Used to control the TV. You need not press the TV button before pressing this button.

38. CHANNEL SELECT BUTTONS

Same as the buttons on the VCR.

39. REC BUTTON

Press to start recording.

40. FAST FORWARD BUTTON

Press to activate fast forward. Press this button during playback, and forward playback picture at high speed can be seen.

41. PAUSE BUTTON

Press to pause during recording or playback.

42. STOP BUTTON

Press to stop tape. The STOP button must be pressed between "RECORD" and another operation.

CONTROLS AND FEATURES

43. F.ADV BUTTON

Press this button during still playback to advance the picture by one frame. Press this button during playback for forward high-speed search that lasts for about 1 minute of playing time, then goes back to normal play mode.

44. TRACKING CONTROL BUTTONS

To minimize noise in playback and slow playback.

45. NUMBER BUTTONS "0" THROUGH "9"

Select any channel (whether or not it is in the "Tuner Scan List") by pressing two buttons. (Press "0" and then "8" for channel 8.) The number buttons are also used for setting the clock and programming the timer.

46. VCR/TV SELECT BUTTON

Selects the signal to be viewed. The VCR indicator comes on when the unit is in VCR mode and the signal received by the VCR is displayed on the TV screen. With the switch in the TV position (indicator light off) the broadcast signal is received directly by your TV set. When the VCR power is turned off, the VCR automatically switches to "TV".

CONTROLS AND FEATURES (cont.) pg. 9

47. LIGHT BUTTON

When this button is pressed, the VOLUME, CHANNEL, REW, F.FWD and PLAY buttons light for about 8 seconds.

Note: The VCR1, TV, CATV or VCR2 button lights according to the mode you have selected.

48. 100/ENT BUTTON

Used to select TV or CATV channels. Press "100", "2", "3" in this order to select channel 123. Press "100", "0" and "5" for channel 105.

49. EDIT BUTTON

Use this button to create an edit program during "Program Easy Edit". See page 50 for details.

50. GO-TO/INDEX BUTTON

Press this button to search for the scene you want to view using the counter GO-TO or INDEX feature.

51. AVX BUTTON

Press to select tuner position to record or view an off-the-air TV program (through the VCR's built-in tuner) the L1 or L2 (line) position to record or view the program input through the video and audio line input jacks.

52. DISPLAY BUTTON

1st Press....Calls up the mode display on TV screen.

2nd Press (before display disappears)....The display on TV screen disappears except for "Linear Time

Counter".

3rd Press....The counter memory "M" appears on TV screen.

Also changes the VCR's display from the clock to the counter.

4th Press....Clears the display on TV screen. Also changes the VCR's display from the counter to the

clock.

53. SLOW SPEED BUTTONS

Press the (-) or (+) button to view the pictures at slow speed. During slow playback the slow speed can be adjusted by pressing the (-) or (+) button.

54. TAPE SPEED SELECT BUTTON

Recording time using Cassette tape T-160: EP: 8 hours SP: 2.6 hours

Notes:

• Playback speed automatically corresponds with recorded speed.

CONTROLS AND FEATURES

• This VCR cannot record in LP mode, but can play LP recorded tapes.

. CLEAR BUTTON

Used for programming the timer. And also used for counter reset button.

56. GUIDE BUTTON

Press this button to use the easy guide system feature. (See page 2 for details.)

57. REW BUTTON

Press to start rewind. Press this button during playback, and reverse playback picture at high speed can be seen.

58. PLAY BUTTON

Press to start play.

59. TV CONTROL BUTTONS

Used for controlling the TV.

60. VCR1 BUTTON

First press this button when operating the VCR with this remote control and then press the button which corresponds to the function you want.

61. POWER BUTTON

Press to turn VCR on. Press again to turn VCR off.

CONTROLS AND FEATURES

CONTROLS AND FEATURES (cont.) pg. 10

USING THE REMOTE CONTROL UNIT

HOW TO INSTALL BATTERIES

NOTES:

1. Be sure to install two "AA" size batteries before use.

2. Be aware of the polarity.

Aim the remote control at the receiver on the front panel of the VCR.

NOTES:

1. If the range is short, try new batteries.

2. An object in between the VCR and remote control unit may block the invisible light beam and operation will not be possible.

3. If you cannot operate the VCR with this remote control, first press the VCR 1 button and then press the button which corresponds to the VCR function you want.

INSTALLATION INTRODUCTION & ANTENNA SYSTEM

INTRODUCTION

Place your Video Cassette Recorder (VCR) in a horizontal position on a solid, stable surface near your TV. Connect the VCR AC plug into a non-switched AC outlet. Before you can use your VCR, the TV antenna connection must be moved to the VCR. Then new connections must be added from the VCR to the TV. An accessory for common connections is included with your VCR. If your installation requires other accessories, they may be purchased at your Dealer or Electronic Parts Stores. There are several installations shown in the following figures. Select the figure which best matches your TV signal source, equipment features, and operating needs. TV broadcasts in your area may be VHF, UHF, or both. In a UHF-only area, use figure A3 for VHF and UHF connections between the VCR and TV. The VHF connection from VCR to TV is always needed for the VCR output channel of VHF Channel 3 or 4. Even if your VCR has Cable Tuning Ability (CTA), cable channels can only be received by connection to a Cable Service.

CABLE SYSTEMS

Cable system features and services vary in each local area. If you presently use your TV with a cable system, please read CABLE SYSTEMS INFORMATION on page 13 before making any connections.

"Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical".

Rabbit ear antenna

Your VCR can be sued with this type of antenna only if the picture is very clear and stable. When the antenna is part of the TV, the leads may not reach the VCR. You can either extend the leads, or obtain a movable rabbit ear antenna. We recommend using an outside antenna.

Note: If your TV has single antenna input (UHF/VHF), use figure A1.

Precautions

• Avoid extreme heat, cold, moisture, dust, magnetic fields, and strong vibrations.

• Protect the VCR from household pets.

• In areas with frequent electrical storms, lightning protection devices attached to the cable/antenna should be checked each year for good connections and condition. AC power line Surge Protection accessories are recommended for the VCR and TV. Such devices are commonly used for computer protection, and will minimize damage to the TV and VCR in the event of AC surge from lightning strike or other cause. Whenever possible, the TV and VCR should be unplugged from AC, and disconnected from the antenna/cable during electrical storms.

CAUTION:

Do not place the VCR by a window where it will be exposed to strong sunlight as it may malfunction.

INSTALLATION INTRODUCTION & ANTENNA SYSTEM (cont.) pg. 12

INSTALLATION CABLE SYSTEM

Figure A1

Figure A2

Figure A3

INSTALLATION CABLE SYSTEM

CABLE SYSTEM INFORMATION

Cable systems vary in features and services. The information and figures which follow cover most installations. If you need information about other installations, please write to Service at the nearest Hitachi address listed at the back of this manual. The tuning abilities of your VCR and the type of cable service you have will determine what connections can be used. The VCR Tuning Range is listed in the rear of this Manual. VCRs with Cable Tuning Ability (CTA) are able to tune channels listed for CATV. Most cable services will be one of the following four types.

1. Basic Cable: Apartment buildings and planned communities may provide this type of service. No channel selection Cable Box is used with the TV. All channels are received using VHF channels 2 - 13. With this system, no special connections or operating procedures are needed. Connect the VCR and TV as shown in figure C1.

2. Extended Cable - A Cable Box is used for TV Channel Selection: The TV is usually set to channel 3 or 4, and all channel selection is performed using the cable company supplied Cable Box. In this type of system, no extra cost channels are available, and no channels are scrambled. A CTA VCR can select channels on this system without a Cable Box, if the channels on the cable are in the VCR tuning range. The Cable Box may still be needed for the TV, unless the VCR is used as a cable converter. You can use figure C1, C2, or C3 for Extended Cable connection. Connections in C1 and C2 need no additional accessories. The connection of figure C3 allows recording and watching different programs but operation is more complicated.

3. Extended Cable With Extra Cost Channels - No Scrambled Channels On System-Cable Converter Box Used For TV: In this type of cable system, extra cost channels are added or deleted before the cable enters the customer home. If a CTA VCR and a CTA TV are used, a Cable Box is not needed. Connections can be made as shown in figure C1. If a non-CTA TV is used with a CTA VCR, either figure C2 or C3 can be used. If both nonCTA VCR and TV are used, figure C2 must be used.

4. Extended Cable With Extra Cost Channels - Scrambled Channels on System-Cable Descrambler/Converter Box Used For TV: In this type of system the cable company supplied Box must always be used to get proper reception of Extra Cost channels. All Extra Cost channels on the cable are scrambled, but the Cable Box unscrambles any that you pay extra to view. Channels included in the basic cable service fee are usually not scrambled, and can be tuned by a CTA VCR or CTA TV.

ADDITIONAL INFORMATION

When any type of scrambling is used for Extra Cost channels, the Cable Box must be used to view or record those channels. A CTA VCR does not include unscrambling ability. that ability is restricted to only cable company supplied equipment. On cable systems with scrambled channels, you have several choices. Among them are: a. Recording and watching only channels selected by the Cable Box (see figure C2). b. Adding a second cable company supplied Box. c. Adding switches to allow either recording and watching the channel selected by the Cable Box or recording a channel which is non-scrambled while watching another channel selected by the Cable Box (see figure C3). Two Cable Systems: In some areas, two cables are used as inputs to the Cable Box. One cable may contain mostly non-scrambled channels, the other mostly Extra Cost scrambled channels. When you have a two-cable system, the cable with non-scrambled channels you wish to record (Cable A or Cable B) can usually be connected as in figure C3. One Cable can be connected directly, or both cables can be accessed by using the Cable Box. If you need to use both cables directly, write Hitachi service for a connection diagram.

INSTALLATION CABLE SYSTEM

CAUTION: Only high quality, low loss switches and splitters should be used. All connections must be with shielded Coax cable. If your added connections degrade the performance of Extra Cost channels, all connections should be removed. The circuit of figure C2 should cause least signal loss. If even the circuit of figure C2 is not satisfactory, consult your cable company about installation.

INSTALLATION CABLE SYSTEM

INSTALLATION CABLE SYSTEM (cont.) pg. 14

CABLE SYSTEM VCR OPERATION Direct Cable Connection

When a direct cable connection is used as in figure C1, VCR operation requires no special procedures.

Setting VCR Channels For Cable

Due to the many channels available on Cable, programming channel memory will require patience. Although the VCR is preset for channels 2 - 13 (air signals), the sequence of channels may be different on cable. For example, channel 6 of the VCR may actually receive channel 28, as identified by the station. Any VCR channel memory position can be programmed to select any channel. Please refer to the section on presetting channel memory for details. (See page 20.)

Cable: Figure C1

INSTALLATION CABLE SYSTEM (cont.) pg. 15

Cable Connection Using Cable Box Only

Interconnect as in figure C2.

1. Set the TV, Cable Box, and VCR power ON. Select a channel on the Cable Box.

2. Set the VCR/TV switch to the VCR position, and set the channel selector of the TV to the Video channel output by the VCR (CH 3/4 setting on RF modulator).

3. Using Channel Up/Down on the VCR, select the channel used for Cable Box output to the TV. You should be able to view the Cable Box output in only one VCR channel setting. If you are correctly set to the Cable Box, changing the channel setting of the VCR to any other channel will provide only a snowy picture. If no picture is obtained, re-check your connections and TV tuning to the VCR output channel. Setting TV tuning to view the VCR output is often easiest by playing a pre-recorded tape. The VCR should now be set to tune the Cable Box. To record from the Cable Box, the Cable Box must be turned ON. If the Cable Box is used to control TV power, and you do not wish to have the TV on during Recording or Timer Recording, turn the TV OFF with the power switch on the TV. If the Cable Box controls the TV volume using a Remote Control, the volume setting must be set to normal. Timer Recording: When you program the Timer for unattended recording, set the VCR to select the VCR channel used to view the Cable Box. The same VCR channel setting must be used for all timer programs. The VCR is unable to control channel selection when it is used with the Cable Box. The VCR can only select the Cable Box or no picture. Before leaving the VCR to perform Timer Recording, be sure to activate the timer mode, set the Cable Box power ON, and set the channel on the Cable Box to the channel you want to record.

Cable: Figure C2

INSTALLATION CABLE SYSTEM (cont.) pg. 16

Accessories required for optional cable connections - not provided

Cable: Figure C3

INSTALLATION CABLE SYSTEM

INSTALLATION CABLE SYSTEM (cont.) pg. 17

Cable Connection Direct or Using Cable Box

When using figure C3 with a non-scrambled cable system, the VCR Input Selector Switch No. 1 and the 2 Way Splitter No. 2 can be omitted, along with the coax interconnecting the two. Connecting the VCR Input directly to splitter No. 1, and the cable box Output directly to A/B switch No. 2.

Function of Accessories 2 Way Splitter No. 1: Divides the cable signal so the signal is provided to the VCR and the Cable Box. A/B Selector Switch No. 1, VCR Recording Input Selector: Used to select the Source for VCR use. In

one position, the cable can be recorded directly. In the other position, the VCR can record the Cable Box. 2 Way Splitter No. 2: Divides the signal from the Cable Box so the VCR can record it, or it can be viewed on TV. A/B Selector Switch No. 2, TV Viewing Switch: Used to allow the TV to view the Cable Box while the VCR is recording Direct cable sources. In the other position, TV can view VCR Recording or Playing. (VCR/TV switch of video tape recorder must be in VCR mode.) Operation: After completing connections, set A/B No. 2 to A position. Verify cable channels to TV. In this position, the TV and Cable Box can be used as previously, except when making unattended recording of the Cable Box. Then the Cable Box power must remain ON. To view what the VCR is Recording or playing, set the switch to position B. Tune the TV to the VCR output channel, and set the VCR/TV Switch to the VCR mode.

Operation of VCR

When the VCR Input Selector Switch A/B No. 1 is in position A, the VCR can record the Cable Box. One channel position of the VCR should be set to tune the Cable Box. Channel position 01 is recommended. Set the VCR as in the section for Using Cable Box Only, when using position A. When the A/B No. 1 is in position B, the VCR operates as indicated in Direct Connection to Cable. Refer to Setting channels for Cable. Remember that when making a Timer Recording using the Cable Box, the Cable Box channel must be programmed into the Timer, the A/B No. 1 switch must be set to A, and Cable Box power must be left ON. When recording the Cable directly, be sure to set the switch to position B. The VCR cannot select betwee the Cable Box and Direct Cable inputs, so unattended recordings of both sources alternately should not be programmed unless someone is available to change the setting of switch A/B No. 1 during Timer operation.

VIDEO CHANNEL SETTING

The RF converter changes the video and audio signals from the tuner or tape playback, to a standard television broadcast signal on channel 3 or 4. To obtain video recorder output on either channel 3 or 4, set the RF converter switch to CH3 or 4 whichever channel is unused in your area.

NORMAL TV VIEWING

You do not need to disconnect VCR from your TV set to watch TV. When you turn off the POWER switch on your VCR, the VCR automatically switches to "TV". To watch TV, turn on TV and select a channel as usual.

SETTING THE CLOCK

Things to know before starting

• The clock uses the 12-hour system. (Be aware of AM and PM.)

• When you first plug in your VCR, the clock will read "--:--".

• While you are setting the clock, the "menu" display on the TV screen will prompt you through the procedures.

• If you press a wrong digit, press GUIDE button and restart the procedure from the beginning.

1. Turn on the power of both VCR and TV.

2. Be sure that the TV is set to the video channel (channel 3 or 4). (See page 17.)

3. Aim the remote control unit at the receiver on the front panel of the VCR.

4. Press the GUIDE button until the "MENU", as illustrated, appears on the TV screen.

Original menu

SELECT NUMBER 1 TO 7 1 VCR PLUS RECORDING 2 DELAYED RECORDING 3 PROGRAM REVIEW

4 INITIAL SETUP 5 CLOCK SET 6 VCR PLUS SETUP 7 PROBLEM GUIDE *TO END PRESS GUIDE

NOTE: If the menu does not appear when the GUIDE button is pressed, press the VCR 1 button and then the

GUIDE button.

5. Press "5" button to set the clock. CLOCK SET

TIME --:- MONTH/DAY/YEAR

DATE --/--/- FILL IN BLINKING SPACE *TO END PRESS GUIDE

6. Set the hour by pressing two number buttons on the remote control unit and two more for the minute (for example, 0 2 1 5 for 2:15).

SETTING THE CLOCK

CLOCK SET

TIME 02:15 PRESS AM:1 PM:2

MONTH/DAY/YEAR

DATE --/--/- FILL IN BLINKING SPACE *TO END PRESS E

SETTING THE CLOCK (cont.) pg. 19

7. Press "1" for AM or "2" for PM.

CLOCK SET

TIME 02:15 PM MONTH/DAY/YEAR

DATE --/--/- FILL IN BLINKING SPACE *TO END PRESS GUIDE

8. Set the date by pressing six digits in order of month, day and year (for example, 1 2 2 0 9 2 for December 20, 1992).

CLOCK SET

TIME 02:15 PM MONTH/DAY/YEAR

DATE 12/20/92 SUN FILL IN BLINKING SPACE *TO END PRESS GUIDE

NOTE: Always press "0" before single-digit months and days.

9. Press GUIDE button to start the clock.

SELECT NUMBER 1 TO 7 1 VCR PLUS RECORDING 2 DELAYED RECORDING 3 PROGRAM REVIEW

+ 58 hidden pages