Hitachi SJ700D-022L, SJ700D-004L, SJ700D-022H, SJ700D-037L, SJ700D-037H Quick Reference Manual
...
SJ700D-3 SERIES
Read through this Quick Reference Guide, and keep it handy for future reference.
HITACHI INVERTER
Quick Reference Guide
NT2311X
Introduction
No.
Revision content
Date of issue
Manual code
1
First edition
April, 2014
NT2311X
Introduction
Thank you for purchasing Hitachi SJ700D-3 Series Inverter. This Quick Reference Guide describes the contents of
planning the installation, installing, commissioning, using and servicing the Hitachi SJ700D-3 Series Inverter.
Please read this document and the instruction manual before operation to perfectly understand proper handling and
safety precautions for the product to ensure safety and proper usage. Before attempting installation, operation and
maintenance work, you should understand the knowledge of equipment, information of safety, caution and how to
use and service the inverter. You should also use the inverter by observing specifications described this guide and
prevent risks by performing maintenance.
This guide is “Quick Reference Guide”. Refer to "SJ700D-3 series Instruction Manual" on CD bundled with the
inverter for more information. If you use the inverter with optional products, also you should read the manuals for
those products. Note that this guide, the instruction manual and the manual for each optional product to be used
should be delivered to the end user of the inverter.
Handling of this Quick Reference Guide and bundled CD (the Instruction Manual)
- The contents of the guide and the CD are subject to change without prior notice.
- Even if you lose the guide and the CD, it will not be resupplied, so please keep it carefully.
- No part of the guide and the CD may be reproduced in any form without the publisher’s permission.
- If you find any incorrect description, missing description or have a question concerning the contents of these
manuals, please contact the publisher.
Revision History
- The current edition of this Quick Reference Guide also includes some corrections of simple misprints, missing
letters, misdescriptions and certain added explanations other than those listed in the above Revision History table.
Safety Instructions
CAUTION
- Many of the drawings in the Quick Reference Guide show the inverter with covers and/or parts blocking your view as
removed. Do not operate the inverter in the status shown in those drawings. If you have removed the covers and/or parts, be
sure to reinstall them in their original positions before starting operation, and follow all instructions in this Instruction
Manual when operating the inverter.
CAUTION
- Install the inverter on a non-flammable surface, e.g., metal. Otherwise, you run the risk of fire.
- Do not place flammable materials near the installed inverter. Otherwise, you run the risk of fire.
- When carrying the inverter, do not hold its top cover. Otherwise, you run the risk of injury by dropping the inverter.
- Prevent foreign matter (e.g., cut pieces of wire, sputtering welding materials, iron chips, wire, and dust) from entering the
inverter. Otherwise, you run the risk of fire.
- Install the inverter on a structure able to bear the weight specified in this Instruction Manual. Otherwise, you run the risk of
injury due to the inverter falling.
- Install the inverter on a vertical wall that is free of vibrations. Otherwise, you run the risk of injury due to the inverter falling.
- Do not install and operate the inverter if it is damaged or its parts are missing. Otherwise, you run the risk of injury.
- Install the inverter in a well-ventilated indoor site not exposed to direct sunlight. Avoid places where the inverter is exposed
to high temperature, high humidity, condensation, dust, explosive gases, corrosive gases, flammable gases, grinding fluid
mist, or salt water. Otherwise, you run the risk of fire.
- The inverter is precision equipment. Do not allow it to fall or be subject to high impacts, step on it, or place a heavy load on
it. Doing so may cause the inverter to fail.
WARNING
- Be sure to ground the inverter. Otherwise, you run the risk of electric shock or fire.
- Commit wiring work to a qualified electrician. Otherwise, you run the risk of electric shock or fire.
- Before wiring, make sure that the power supply is off. Otherwise, you run the risk of electric shock or fire.
- Perform wiring only after installing the inverter. Otherwise, you run the risk of electric shock or injury.
- Do not remove rubber bushings from the wiring section. Otherwise, the edges of the wiring cover may damage the wire,
resulting in a short circuit or ground fault.
CAUTION
- Make sure that the voltage of AC power supply matches the rated voltage of your inverter. Otherwise, you run the risk of
injury or fire.
- Do not input single-phase power into the inverter. Otherwise, you run the risk of fire.
- Do not connect AC power supply to any of the output terminals (U, V, and W). Otherwise, you run the risk of injury or fire.
- Do not connect a resistor directly to any of the DC terminals (PD, P, and N). Otherwise, you run the risk of fire.
- Connect an earth-leakage breaker to the power input circuit. Otherwise, you run the risk of fire.
- Use only the power cables, earth-leakage breaker, and magnetic contactors that have the specified capacity (ratings).
Otherwise, you run the risk of fire.
- Do not use the magnetic contactor installed on the primary and secondary sides of the inverter to stop its operation.
- Tighten each screw to the specified torque. No screws must be left loose. Otherwise, you run the risk of fire.
- Before operating, slide switch SW1 in the inverter, be sure to turn off the power supply. Otherwise, you run the risk of
electric shock and injury.
- Since the inverter supports two modes of cooling-fan operation, the inverter power is not always off, even when the cooling
fan is stopped. Therefore, be sure to confirm that the power supply is off before wiring. Otherwise, you run the risk of electric
shock and injury.
CAUTION
CAUTION
WARNING
Safety Instructions
Be sure to read this Quick Reference Guide and appended documents thoroughly before installing, operating,
maintaining, or inspecting the inverter. In this Quick Reference Guide, safety instructions are classified into two
levels, namely WARNING and CAUTION.
: Indicates that incorrect handling may cause hazardous situations, which may result in serious
personal injury or death.
: Indicates that incorrect handling may cause hazardous situations, which may result in
moderate or slight personal injury or physical damage alone.
Note that even a level situation may lead to a serious consequence according to circumstances.
Be sure to follow every safety instruction, which contains important safety information. Also focus on and observe
the items and instructions described under "Notes" in the text.
1. Installation
2. Wiring
i
Safety Instructions
WARNING
- While power is supplied to the inverter, do not touch any terminal or internal part of the inverter, check signals, or connect or
disconnect any wire or connector. Otherwise, you run the risk of electric shock or fire.
- Be sure to close the terminal block cover before turning on the inverter power. Do not open the terminal block cover while
power is being supplied to the inverter or voltage remains inside. Otherwise, you run the risk of electric shock.
- Do not operate switches with wet hands. Otherwise, you run the risk of electric shock.
- While power is supplied to the inverter, do not touch the terminal of the inverter, even if it has stopped. Otherwise, you run
the risk of injury or fire.
- If the retry mode has been selected, the inverter will restart suddenly after a break in the tripping status. Stay away from the
machine controlled by the inverter when the inverter is under such circumstances. (Design the machine so that human safety
can be ensured, even when the inverter restarts suddenly.) Otherwise, you run the risk of injury.
- Do not select the retry mode for controlling an elevating or traveling device because output free-running status occurs in retry
mode. Otherwise, you run the risk of injury or damage to the machine controlled by the inverter.
- If an operation command has been input to the inverter before a short-term power failure, the inverter may restart operation
after the power recovery. If such a restart may put persons in danger, design a control circuit that disables the inverter from
restarting after power recovery. Otherwise, you run the risk of injury.
- The [STOP] key is effective only when its function is enabled by setting. Prepare an emergency stop switch separately.
Otherwise, you run the risk of injury.
- If an operation command has been input to the inverter before the inverter enters alarm status, the inverter will restart
suddenly when the alarm status is reset. Before resetting the alarm status, make sure that no operation command has been
input.
- While power is supplied to the inverter, do not touch any internal part of the inverter or insert a bar in it. Otherwise, you run
the risk of electric shock or fire.
CAUTION
- Do not touch the heat sink, which heats up during the inverter operation. Otherwise, you run the risk of burn injury.
- The inverter allows you to easily control the speed of motor or machine operations. Before operating the inverter, confirm
the capacity and ratings of the motor or machine controlled by the inverter. Otherwise, you run the risk of injury.
- Install an external brake system if needed. Otherwise, you run the risk of injury.
- When using the inverter to operate a standard motor at a frequency of over 60 Hz, check the allowable motor speeds with
the manufacturers of the motor and the machine to be driven and obtain their consent before starting inverter operation.
Otherwise, you run the risk of damage to the motor and machine.
- During inverter operation, check the motor for the direction of rotation, abnormal sound, and vibrations. Otherwise, you run
the risk of damage to the machine driven by the motor.
WARNING
- Before inspecting the inverter, be sure to turn off the power supply and wait for 10 minutes or more. Otherwise, you run the
risk of electric shock. (Before inspection, confirm that the Charge lamp on the inverter is off and the DC voltage between
terminals P and N is 45 V or less.)
- Commit only a designated person to maintenance, inspection, and the replacement of parts. (Be sure to remove wristwatches
and metal accessories, e.g., bracelets, before maintenance and inspection work and to use insulated tools for the work.)
Otherwise, you run the risk of electric shock and injury.
WARNING
- Never modify the inverter. Otherwise, you run the risk of electric shock and injury.
CAUTION
- Do not discard the inverter with household waste. Contact an industrial waste management company in your area who can
treat industrial waste without polluting the environment.
3. Operation
4. Maintenance, inspection, and parts replacement
5. Others
ii
Safety Instructions
WARNING: This equipment must be installed, adjusted, and maintained by qualified engineers who have
expert knowledge of electric work, inverter operation, and the hazardous circumstances that
can occur. Otherwise, personal injury may result.
Caution for EMC (Electromagnetic Compatibility) (0.4kW-150kW)
The SJ700D series inverter conforms to the requirements of Electromagnetic Compatibility (EMC) Directive
(2004/108/EC). However, when using the inverter in Europe, you must comply with the following specifications and
requirements to meet the EMC Directive and other standards in Europe:
1. Power supply requirements
a. Voltage fluctuation must be -15% to +10% or less.
b. Voltage imbalance must be ±3% or less.
c. Frequency variation must be ±4% or less.
d. Total harmonic distortion (THD) of voltage must be ±10% or less.
2. Installation requirement
a. The integrated filter in the SJ700D series inverter must be enabled. (See chapter 2 Installation andWiring)
* When using the specific external filter for the SJ700D series inverter, please refer to the instruction
described in the dedicated guide book for the filter.
3. Wiring requirements
a. A shielded wire (screened cable) must be used for motor wiring, and the length of the cable must be
according to the following table (Table 1).
b. The carrier frequency must be set according to the following table to meet an EMC requirement (Table 1).
c. The main circuit wiring must be separated from the control circuit wiring.
4. Environmental requirements (to be met when a filter is used)
a. Ambient temperature must be within the range -10°C to +50°C.
b. Relative humidity must be within the range 20% to 90% (non-condensing).
c. Vibrations must be 5.9 m/s2 (0.6 G) (10 to 55 Hz) or less. (0.4 to 22kW)
2.94 m/s2 (0.3 G) (10 to 55Hz) or less. (30 to 150kW)
d. The inverter must be installed indoors (not exposed to corrosive gases and dust) at an altitude of 1,000 m
or less.
iii
Safety Instructions
model
cat.
cable
length(m)
carrier
frequency(kHz)
model
cat.
cable
length(m)
carrier
frequency(kHz)
SJ700D-004L
C3 5 2.5
SJ700D-007L
C3 5 2.5
SJ700D-007H
C3 5 2.5
SJ700D-015L
C3 5 2.5
SJ700D-015H
C3 5 2.5
SJ700D-022L
C3 5 2.5
SJ700D-022H
C3 5 2.5
SJ700D-037L
C3 5 2.5
SJ700D-037H
SJ700D-040H
C3 5 2.5
SJ700D-055L
C3 1 1
SJ700D-055H
C3 1 2.5
SJ700D-075L
C3 1 1
SJ700D-075H
C3 1 2.5
SJ700D-110L
C3 1 1
SJ700D-110H
C3 1 2.5
SJ700D-150L
C3 1 1
SJ700D-150H
C3 1 2.5
SJ700D-185L
C3 1 1
SJ700D-185H
C3 1 2.5
SJ700D-220L
C3 5 2.5
SJ700D-220H
C3 1 2.5
SJ700D-300L
C3 5 2.5
SJ700D-300H
C3 1 2.5
SJ700D-370L
C3 5 2.5
SJ700D-370H
C3 1 2.5
SJ700D-450L
C3 5 2.5
SJ700D-450H
C3 5 2.5
SJ700D-550L
C3 5 2.5
SJ700D-550H
C3 5 2.5
SJ700D-750H
C3
10
2.5
SJ700D-900H
C3
10
2.5
SJ700D-1100H
C3
10
2.5
SJ700D-1320H
C3
10
2.5
SJ700D-1500H
C3
10
2.5
Table 1
iv
Safety Instructions
Model No.
Required Torque (N.m)
Wire Range (AWG)
SJ700D-004L
1.8
14(Stranded only)
SJ700D-007L
1.8
14(Stranded only)
SJ700D-015L
1.8
14(Stranded only)
SJ700D-022L
1.8
14(Stranded only)
SJ700D-037L
1.8
10(Stranded only)
SJ700D-050L
3.0
8
SJ700D-055L
4.0
8
SJ700D-075L
4.0
6
SJ700D-110L
4.0
6-4
SJ700D-150L
4.9
2
SJ700D-185L
4.9
1
SJ700D-220L
8.8
1 or 1/0
SJ700D-300L
8.8
2/0 or Parallel of 1/0
SJ700D-370L
20.0
4/0 (Prepared wire only) or Parallel of 1/0
SJ700D-450L
20.0
4/0 (Prepared wire only) or Parallel of 1/0
SJ700D-550L
19.6
350 kcmil
(Prepared wire only) or Parallel of 2/0 (Prepared wire only)
Cautions for UL and cUL (0.4kW-150kW)
(Standard to comply with: UL508C, CSA C22.2 No14-5)
Warning Markings
GENERAL:
These devices are open type and/or Enclosed Type 1 (when employing accessory Type 1 Chassis Kit) AC Inverters
with three phase input and three phase output. They are intended to be used in an enclosure. They are used to
provide both an adjustable voltage and adjustable frequency to the ac motor. The inverter automatically maintains
the required volts-Hz ration allowing the capability through the motor speed range.
(1) “Use 60/75C CU wire only” or equivalent.
For models SJ700D series except for models SJ700D-055H, SJ700D-075H, SJ700D-110H.
(2) “Use 75C CU wire only” or equivalent.
For models SJ700D series except for SJ700D-075H, SJ700D-110H, SJ700D-055H.
(3) “Suitable for use on a circuit capable of delivering not more than 100,000rms symmetrical amperes,
240V maximum”. For models with suffix L.
(4) “Suitable for use on a circuit capable of delivering not more than 100,000 rms symmetrical amperes,
480V maximum”. For models with suffix H.
(5) “Install device in pollution degree 2 environment”
(6) “Maximum Surrounding Air Temperature 45 or 50C”
(7) “CAUTION - Risk of Electric Shock - Capacitor discharge time is at least 10 min.”
(8) ”Integral solid state short circuit protection does not provide branch circuit protection.
Branch circuit protection must be provided in accordance with the NEC and any additional local codes”
(9) “Solid State motor overload protection reacts with max. 120% of FLA”.
(10) Tightening torque and wire range for field wiring terminals are in the table below:
v
Safety Instructions
Model No.
Fuse Size (Maximum A)
Circuit Breaker (A)
Type
Rating Type
SJ700D-004L
J
30 A
SJ700D-004L
J
SJ700D-007L
J
30 A
SJ700D-007L
J
SJ700D-015L
J
30 A
SJ700D-015L
J
SJ700D-022L
J
30 A
SJ700D-022L
J
SJ700D-037L
J
30 A
SJ700D-037L
J
SJ700D-050L
J
30 A
SJ700D-050L
J
SJ700D-055L
J
100 A
SJ700D-055L
J
SJ700D-075L
J
100 A
SJ700D-075L
J
SJ700D-110L
J
100 A
SJ700D-110L
J
SJ700D-150L
J
125 A
SJ700D-150L
J
SJ700D-185L
J
125 A
SJ700D-185L
J
SJ700D-220L
J
125 A
SJ700D-220L
J
SJ700D-300L
J
225 A
SJ700D-300L
J
SJ700D-370L
J
225 A
SJ700D-370L
J
SJ700D-450L
J
250 A
SJ700D-450L
J
SJ700D-550L
J
300 A
SJ700D-550L
J
Model No.
Required Torque (N.m)
Wire Range (AWG)
SJ700D-007H
1.8
14(Stranded only)
SJ700D-015H
1.8
14(Stranded only)
SJ700D-022H
1.8
14(Stranded only)
SJ700D-037H
1.8
14(Stranded only)
SJ700D-040H
1.8
14(Stranded only)
SJ700D-055H
4.0
12
SJ700D-075H
4.0
10
SJ700D-110H
4.0
8
SJ700D-150H
4.9
6
SJ700D-185H
4.9
6
SJ700D-220H
4.9
6 or 4
SJ700D-300H
4.9
3
SJ700D-370H
20.0
1
SJ700D-450H
20.0
1
SJ700D-550H
20.0
2/0
SJ700D-750H
20.0
Parallel of 1/0
SJ700D-900H
20.0
Parallel of 1/0
SJ700D-1100H
35.0
Parallel of 3/0
SJ700D-1320H
35.0
Parallel of 3/0
SJ700D-1500H
35.0
Parallel of 3/0
(11) Distribution fuse / circuit breaker size marking is included in the manual to indicate that the unit shall be
connected with a listed inverse time circuit breaker, rated 600 V with the current ratings as shown in the
table below:
vi
Safety Instructions
Model No.
Fuse Size (Maximum A)
Circuit Breaker (A)
Type
Rating
Type
SJ700D-007H
J
20 A
SJ700D-007H
J
SJ700D-015H
J
20 A
SJ700D-015H
J
SJ700D-022H
J
20 A
SJ700D-022H
J
SJ700D-037H
J
20 A
SJ700D-037H
J
SJ700D-040H
J
20 A
SJ700D-040H
J
SJ700D-055H
J
40 A
SJ700D-055H
J
SJ700D-075H
J
40 A
SJ700D-075H
J
SJ700D-110H
J
40 A
SJ700D-110H
J
SJ700D-150H
J
75 A
SJ700D-150H
J
SJ700D-185H
J
75 A
SJ700D-185H
J
SJ700D-220H
J
75 A
SJ700D-220H
J
SJ700D-300H
J
100 A
SJ700D-300H
J
SJ700D-370H
J
100 A
SJ700D-370H
J
SJ700D-450H
J
150 A
SJ700D-450H
J
SJ700D-550H
J
150 A
SJ700D-550H
J
SJ700D-750H
J
225 A
SJ700D-750H
J
SJ700D-900H
J
225 A
SJ700D-900H
J
SJ700D-1100H
J
300 A
SJ700D-1100H
J
SJ700D-1320H
J
350 A
SJ700D-1320H
J
Note) Please select an appropriate fuse or an appropriate circuit breaker for a system.
(12) “Field wiring connection must be made by a UL Listed and CN closed-loop terminal connector sized for the
wire gauge involved. Connector must be fixed using the crimp tool specified by the connector
manufacturer.”
(13) “Motor over temperature protection is not provided by the drive.”
DANGER! RISQUE DE BLESSURE OU DE CHOC ELECTRIQUE
- Lire attentivement le manuel avant l’installation et suivre les instructions
- Avant d’intervenir dans le variateur, couper le circuit de puissance et attendre 10 minutes avant d’ouvrir le capot
vii
SJ700-2 to SJ700D-3
Subject
SJ700-2
SJ700D-3
Point!
Dual rating
Constant torque/
Variable torque
N/A
Selectable
If the inverter drives the light
load application (e.g. fan pump
application), you can choose
the one size smaller capacity
inverter than the motor capacity,
which allows you to reduce the
total cost of your system.
Easy sequence
(EzSQ) – Drive
program function
Process with 1 task.
Supporting 5 tasks
processing with
improved user
friendliness.
The inverter processes 5 tasks at
the same time, which allows you
to realize 5 times faster EzSQ
processing in maximum.
Optional LCD
Operator
WOP operator
(2-line LCD)
Full compatibility with
WOP operator
(5-line LCD and
multi-language)
WOP, the optional LCD
Operator, provides several user
friendliness;
− Multi data monitoring
− Parameter configuration as
monitoring data
− Parameter / Program copy
− Multi-language display
RS-485 serial
communications
19.2kbps (maximum)
115.2kbps (maximum),
and so on.
Approx. 6 times faster
communication in comparison
with the former model are
supported. In addition, some
communication commands are
newly supported.
Initialization
After setting b084
(initialization selection),
press some keys.
In addition to the
conventional method,
executing initialization
by a parameter is
possible.
(Select b084 and
b180=01 : enable the
initializing)
You can initialize easily only by
setting the parameter and no
special procedure is required
Phase loss
protection
Phase loss input
protection
Phase loss input
protection
Phase loss output
protection
Protection function expands to
not only input side but output
side, which provides more
reliable protection against the
phase loss.
The Hitachi SJ700D-3 series succeed the SJ700-2 series with the additional and enhanced features.
The table below is a belief summary of the major improved features.
Contents
Start-up Commissioning the drive
S.1 Quick installation and commissioning flowchart ................................................................................... S - 2
S.2 Instructing in using the panel.................................................................................................................. S - 3
S.3 Example of I/O connections ................................................................................................................... S - 4
S.4 Basic Parameter Setting to Drive Motor ................................................................................................. S - 8
S.4.1 Setting Frequency command source and Run command source .............................................. S - 8
S.4.2 Frequency command source selection ..................................................................................... S - 9
S.4.3 Run command source selection ............................................................................................... S - 11
S.5 Selecting the control mode ..................................................................................................................... S - 13
Chapter 1 Overview
1.1 Inspection of the Purchased Product ············································································· 1 - 2
1.1.1 Inspecting the product·················································································· 1 - 2
1.1.2 Quick Reference Guide and Instruction Manual···················································· 1 - 2
1.2 Method of Inquiry and Product Warranty ······································································· 1 - 3
1.2.1 Method of inquiry ······················································································ 1 - 3
1.2.2 Product warranty ························································································ 1 - 3
1.2.3 Warranty Terms ························································································· 1 - 3
1.3 Exterior Views and Names of Parts ·············································································· 1 - 4
Chapter 2 Installation and Wiring
2.1 Installation ·········································································································· 2 - 2
2.1.1 Precautions for installation ············································································ 2 - 3
2.1.2 Backing plate ································ ···························································· 2 - 5
2.2 Wiring ··············································································································· 2 - 6
2.2.1 Terminal connection diagram and explanation of terminals and switch settings ··············· 2 - 7
2.2.2 Wiring of the main circuit ············································································· 2 - 10
2.2.3 Wiring of the control circuit ··········································································· 2 - 19
2.2.4 Wiring of the digital operator ········································································· 2 - 20
Chapter 3 Operation
3.1 Operating Methods ································································································· 3 - 2
3.2 How to operate the Digital Operator (OPE-SBK) ····························································· 3 - 4
3.2.1 Names and functions of components ······························································· 3 - 4
3.2.2 Code display system and key operations ···························································· 3 - 5
Chapter 4 List of Data Settings
4.1 Precautions for Data Setting ······················································································ 4 - 2
4.2 Monitoring Mode ·································································································· 4 - 2
4.3 Function Mode ····································································································· 4 - 3
4.4 Extended Function Mode ························································································· 4 - 4
Chapter 5 Error Codes
5.1 Error Codes and Troubleshooting ················································································ 5 - 2
5.1.1 Error codes ······························································································ 5 - 2
5.1.2 Trip conditions monitoring ············································································ 5 - 4
5.2 Warning Codes ····································································································· 5 - 5
Chapter 6 Specifications
6.1 Specifications ······································································································· 6 - 2
6.2 External dimensions ······························································································· 6 - 5
Contents
(Memo)
Start-up Commissioning the drive
This chapter contains quick installation and commissioning flowchart to drive the motor.
S.1 Quick installation and commissioning flowchart ............. S - 2
S.2 Instructing in using the panel ........................................... S - 3
S.3 Example of I/O connections ............................................. S - 4
S.4 Basic Parameter Setting to Drive Motor .......................... S - 8
S.5 Selecting the control mode ............................................... S - 13
Start-up Commissioning the drive
Start to confirm
Product inspection
Refer to chapter 1.
Installing
Wiring
Selecting the suitable control mode
End of Confirmation and start to drive
ON
Motor
Speed
Time
RUN
Frequency
command
Motor
speed
Refer to section 2.1.
・Installing
Initial settings of
SJ700D-****FF3
Initial settings of
3
Example 1
Example 2
Example 3
Example 4
Frequency
command
Data setting
(Operator)
External analog signal
(Voltage)
Data setting
(Multi-speed)
External analog signal
(Voltage and Current)
Drive
command
Push key
(Operator)
Push key
(Operator)
External signal
Before setting parameters,
see section S.2.
For basic settings to drive
the motor, see section S.4.
Example of basic setup
the motor, see section S.3.
Setting of control mode
see section S.5
Refer to section 2.2.
・Wiring
What are the desired sources
RUN command?
Setting of commands
S.1 Quick installation and commissioning flowchart
command
(IO connection) to drive
for giving frequency and
SJ700D-****FEF
External signal
S - 2
Start-up Commissioning the drive
Key
Operation
Display(Example)
Use examples (*** is a three digit number)
d001 ←→ 0.00
(Frequency monitor)
In case d*** or F*** display on the panel, indication changes
between parameters and data with pushing FUNC key.
A--- → A044
↑ ↓
A044 ← 00
(Control mode)
In case A***, B***, C***, H***, P*** or U*** display on the
panel, indication changes among A--- (head of group), A044
(parameter) and 00 (data) with pushing FUNC key.
00 → A044
(Control mode)
When the panel indication displays 00 (data), the inverter saves the
displayed value as the new setting with pushing the STR key, and
panel indication changes to the A044 (parameter). The saved data
are held even if the power supply to the inverter is turned off.
d001→d002→…
→F004→A---→…
Panel Indication scrolls up through d***, F*** and the heads of
group (for example A---, B---, C---, H---, P--- and U---).
1.00→1.01→…
A011→A012→…
The value increases if panel indication displays parameters or data.
Holding the key down changes the value faster.
A---→F004→…→
d002→d001→…
Panel indication scrolls down through d***, F*** and the heads of
group (for example A---, B---, C---, H---, P--- and U---).
1.01→1.00→…
A012→A011→…
The value decreases if panel indication displays parameters or data.
Holding the key down changes the value faster.
Simultaneously
A044→’A’044
Pushing simultaneously enables to change each digit directly.
Operating of
the blinking digit is as follows.
0.00→’0’.00
FUNC
STR
1
2
2
1
A
ALARM
POWER
%
RUN
PRG
V
Hz
STR
FUNC
RUN
STOP/
RESET
kW
STR
FUNC
1
2
Left
Right/Save
Increasing
Decreasing
S.2 Instructing in using the panel
This section describes how to use the operator to
change the settings.
For more information, refer to the SJ700D-3 manual or
section 3.2 : How to operate the Digital Operator.
Indication of using the control panel Standard Operator (OPE-SBK)
*) In some cases parameters and data are discontinuous.
(For more information, refer to SJ700D-3 manual.)
S - 3
Start-up Commissioning the drive
Parameter
Details
Setting data
A001
Digital Operator
A002
Digital Operator
F001
Output frequency setting
.Note)
ELB
R/L1
S/L2
T/L3 R T
R0
T0
P
PD N RB
U
V
W
M
3-phase induction motor
RUN
STOP/
RESET
S.3 Example of I/O connections
Example 1: Frequency command source Setting data in F001 (Digital Operator)
Run command source RUN/STOP key (Digital Operator)
*) SJ700D-****FF3 (Initial settings)
(1) I/O connections
(2) Operation
Frequency: By using the digital operator, set the frequency command into parameter F001.
Run/Stop: Push the key and on the digital operator to run and stop.
*) Refer to section S.4.2 for changing the frequency command source and section S.4.3 for changing the run
command source.
(3) Parameter settings
Note) Initial settings are 0.00Hz. You need to set the appropriate data.
S - 4
Start-up Commissioning the drive
Parameter
Details
Setting data
A001
Control circuit terminal block
A002
Digital Operator
H O L
Potentiometer
R/L1
S/L2
T/L3
R T R0
T0
P
PD N RB
ELB
U
V
W
M
3-phase induction motor
RUN
STOP/
RESET
Example 2: ：Frequency command source External potentiometer (Control terminal)
Run command source RUN/STOP key (Control panel)
(1) I/O connections
(2) Operation
Frequency: Set the frequency command via a potentiometer connected to H/O/L terminal.
Run/Stop: Push the key and to run and stop.
*) Refer to section S.4.2 for changing the frequency command source and section S.4.3 for changing the run
command source.
(3) Parameter settings
S - 5
Start-up Commissioning the drive
Parameter
Details
Setting data
A001
Digital Operator
A002
Control circuit terminal block
A020
Multi speed 1 and 2 are not active.
.Note)
A021
Multi speed 1is active and
multi speed 2 is not active.
.Note)
A022
Multi speed 1is not active and
multi speed 2 is active.
.Note)
FW
8：RV
CM1
Forward
7：CF1
6：CF2
P24
PLC
Reverse
Multi-speed1
Multi-speed2
CM1
P24
PLC
Sink logic
Source logic
R/L1
S/L2
T/L3
R
T
R0
T0
P
PD N RB
ELB
U
V
W
M
3-phase induction motor
Example 3: Frequency command source Setting data in F001 (Control panel) + multi speed select
Run command source External signal (Control terminal)
(1) I/O connections
*) In case of SJ700D-****FUF3, you need to set C006=03 and C016=00.
*) You need to set multi speed frequency command into parameters (from A020 to A022).
*) Refer to section S.4.2 for changing the frequency command source and section S.4.3 for changing the run
command source.
(2) Operation
Frequency: By using the multi speed terminals, set the frequency command.
Run/Stop: Using the forward / reverse terminal to run and stop.
(3) Parameter settings
Note) Initial settings are 0.00Hz. You need to set the appropriate data.
S - 6
Start-up Commissioning the drive
Parameter
Details
Setting data
A001
Control circuit terminal block
A002
Control circuit terminal block
FW
8：RV
CM1
Forward
2：AT
P24
PLC
Reverse
Analog select
CM1
P24
PLC
Sink logic
Source logic
R/L1
S/L2
T/L3 R T
R0
T0
P
PD N RB
OI O L
Voltage source
(0V to 10V)
Current source
(4mA to 20mA)
ELB
U
V
W
(+)
(-)
(+)
(-)
M
3-phase induction motor
Example 4: Frequency command source External analog voltage source and current source (Control terminal)
Run command source External signal (Control terminal)
*) SJ700D-****FEF3/FUF3 (Initial settings)
(1) I/O connections
*) Refer to S.4.2 for changing the frequency command source and S.4.3 for changing the run
command source.
(2) Operation
Frequency: Using the voltage source and current source to set the frequency command with analog
select terminal (AT terminal: OFF: Voltage command / ON: Current command).
* AT terminal is used to switch the analog input O and OI to which the inverter refers as the
frequency command. (e.g. When AT terminal is OFF, the inverter outputs the frequency
according to the voltage input given to the O terminal)
Run/Stop: Using the forward / reverse terminal to run and stop.
(3) Parameter settings
S - 7
Start-up Commissioning the drive
Parameter
Detail
Data range
Initial settings
****FF3
****FEF3
****FUF3
A001
Frequency source
00(keypad potentiometer)
01(control circuit terminal block)
02(operator)
03(RS485)
04(option 1)
05(option 2)
06(pulse-string input)
07(easy sequence)
10(operation function result)
02
01
A002
Run command source
01(control circuit terminal block)
02(operator)
03(RS485)
04(option 1)
05(option 2)
02
01
S.4 Basic Parameter Setting to Drive Motor
S.4.1 Setting Frequency command source and Run command source
This section describes how to drive the motor with SJ700D briefly.
The frequency and run command are necessary to drive the motor with the inverter.
In many cases, these sources are set as below;
Setting the frequency : (A) Data settings (Digital operator)
(B) Via external analog signals (Control terminal)
Run and stop : (A) RUN / STOP key (Digital operator)
(B) Via external signal (Control terminal)
The frequency command and Run command sources can be changed by the parameter A001 (Frequency command
source) and A002 (Run command source) respectively.
In addition to the basic setting mentioned above, there are several options for A001 and A002 setting.
*) This chapter explains 01(control circuit terminal block) and 02(operator) mainly.
S - 8
Start-up Commissioning the drive
Procedure
Key operation
Indication
Details
1-1
.
After powering up of the inverter, the operator displays 0.00,
output frequency monitor (d001)
1-2
Indication changes from data display (0.00) to parameter
display (d001).
1-3
or
Push the key and select the head of Group A.
1-4
Push the key and indication changes from A--- to A001.
1-5
Push the key and indication changes to 02(operator).
1-6
Push the key and change from 02 to 01 (control circuit
terminal block).
1-7
Push the key and indication changes A001 (Data save).
1-8
.
By pushing the key for more than three seconds,
indication changes to the output frequency data (d001).
(It depends on b038 setting)
Procedure
Key operation
Indication
Details
1-5’
Push the key and indication changes to 01(control circuit
terminal block).
1-6’
Push the key and change the data to 02 (operator).
FUNC
2
1
FUNC
FUNC
2
STR
FUNC
FUNC
1
S.4.2 Frequency command source selection
Key operation to set A001
****FF3 : Change A001 from 02 (operator) to 01 (control circuit terminal block).
****FEF3/FUF3 : Change from 01 (control circuit terminal block) to 02 (operator).
*) Replace the procedure 1-5 and 1-6 in the list above with 1-5’ and 1-6’ in the list below.
S - 9
Start-up Commissioning the drive
Procedure
Key operation
Indication
Details
1
.
After powering up of the inverter, the operator displays
0.00, output frequency monitor (d001)
2
Indication changes from data (0.00) to parameter (d001).
3
or
Push the key and select F001 (setting frequency).
4
.
Push the key and indication changes setting frequency.
5
or
.
(Example) Set the frequency to 40Hz.
6
Push the key and indication goes back to F001 (Data save).
note)
7
.
By pushing the key for more than three seconds,
the indication changes to the output frequency data.
(It depends on b038 setting)
Parameters
Condition
Setting
A001
Operator
*1)
A020
Multi speed 1 and 2 are not active.
.*2)
A021
Multi speed 1is active and
multi speed 2 is not active.
.*2)
A022
Multi speed 1is not active and
multi speed 2 is active.
.*2)
FUNC
2
1
FUNC
2
1
STR
FUNC
Setting frequency command
(A) A001=02: Digital operator
With this setting, the value set in the parameter F001 defines the target frequency of the inverter.
The procedure below shows an example of a procedure to set F001=40Hz.
note) In case of the setting A001=02, on displaying the output frequency, the setting frequency can change by the
up and down keys.
(B) A001=01: Control terminal
The frequency command can be changed in accordance with the analog input given to the O/OI terminal on the
control terminal by using a potentiometer (connected to H/O/L terminal) or an analog voltage / current supply.
With this setting, the parameter F001 indicates the frequency command value given via the control terminal.
Please refer to the instruction manual for the detailed information about the analog input (e.g. adjustment of he
start / end value).
(C) Multi-speed selection – Binary operation
The inverter can store several target frequencies (up to 16), which is useful to define such low / middle / high
frequencies and those frequencies are switched by external signals. The actual target frequency is selected from
those pre-set frequencies in accordance with the signal status of the multi speed inputs. This part describes an
example using 3 frequency sets.
*1) In case multi speed 1 and 2 are not active, the setting of A001 defines the frequency command source.
In case of A001=02, and if multi speed 1 and 2 are not active, F001 adopts the A020 value.
*2) Initial settings are 0.00Hz. You should set the appropriate data.
S - 10
Start-up Commissioning the drive
Procedure
Key operation
Indication
Details
2-1
.
After powering up of the inverter, the operator displays
0.00, output frequency monitor (d001)
2-2
Indication changes from data (0.00) to parameter (d001).
2-3
or
Push the key and select the head of Group A.
2-4
Push the key and indication changes to A001.
2-5
Push the key and select A002 (Run command source).
2-6
Push the key and indication changes to 02(operator).
2-7
Push the key and change the data to 01 (control circuit
terminal block).
2-8
Push the key and indication changes to A002 (Data save).
2-9
.
By pushing the key for more than three seconds,
indication changes to the output frequency data.
(It depends on b038 setting)
Procedure
Key operation
Indication
Details
2-6’
Push the key and indication changes to 01 (control circuit
terminal block).
2-7’
Push the key and change to 02(operator).
FUNC
2
1
FUNC
1
FUNC
2
STR
FUNC
FUNC
1
S.4.3 Run command source selection
Key operation to set A002
****FF3 : Change from 02 (operator) to 01 (control circuit terminal block).
****FEF3/FUF3 : Change 01 (control circuit terminal block) to 02 (operator).
*) Replace the procedure 2-6 and 2-7 on the list above with 2-6’ and 2-7’ in the list below.
S - 11
Start-up Commissioning the drive
RUN
STOP/
ON
Motor
Speed
Time
RUN
command
Frequency
command
Motor
speed
Operating run command
(A) A001=02: Digital operator
RUN and STOP key on the digital operator allows you to start and stop the motor respectively.
RUN: STOP:
RESET
*) Changing the rotatory direction can be done by changing the parameter F004, keypad run key routing or to
exchange any two phases of the wiring to the motor. Before wiring, you should confirm that the power supply
to the inverter has been cut off.
(B) A001=01: Control terminal
You can start and stop the motor operation via the FW terminal (forward rotation) or RV terminal (Reverse
rotation).
In case of terminal FW:
Sink logic (short between P24 and PLC)
FW-CM1 short: The inverter runs the motor in the forward direction --- RUN command is active.
FW-CM1 open: The inverter decelerates and stops the motor --- RUN command is not active.
Source logic (short between CM1 and PLC)
FW-P24 short: The inverter runs the motor in the forward direction --- RUN command is active.
FW-P24 open: The inverter decelerates and stops the motor --- RUN command is not active.
S - 12
Start-up Commissioning the drive
Check
In case you want to drive fun, pump or light load
application :
-Using the reduced torque mode (A044=01)
-Use the light load mode (b049=01) to drive the motor
with the one size smaller inverter.
In case you want to set the characteristic of
voltage/frequency freely :
-Using Free V/f mode (A044=02)
In case you want to drive the application which
requires high torque control without the motor
feedback :
-Using sensor-less vector mode (A044=03)*
In case you want to drive the application which
requires the high torque control at low frequency range
without the motor feedback.
-Using 0Hz sensor-less vector mode (A044=04)*
In case you want to
- drive the application which requires high torque
control
- drive the application which requires the position
control with the motor feedback :
-Using vector control mode (A044=05)*
S.5 Selecting the control mode
The SJ700D-3 inverter series provides several options for motor control to satisfy various application
requirements. Please choose a suitable control mode for your application by referring to the table below.
Initial setting of A044 is 00 (V/f control mode).
*) Depending on the load, applying the one size bigger inverter may be required. For more information,
refer to SJ700D-3 manual.
S - 13
Start-up Commissioning the drive
(Memo)
S - 14
Chapter 1 Overview
This chapter describes the inspection of the purchased product, the product warranty, and the
names of parts.
1.1 Inspection of the Purchased Product ······· 1 - 2
1.2 Method of Inquiry and Product Warranty · 1 - 3
1.3 Exterior Views and Names of Parts ········ 1 - 4
Chapter 1 Overview
Specification label
Figure 1 Location of the specifications label
Figure 1-2 Contents of the specifications label
Inverter model
Input ratings
Output ratings
Serial number
Model: SJ700D-150HFF3
50Hz,60Hz 380-480V 3 Ph 35/41A
Output/Sortie: 0 - 400Hz 380-480V 3 Ph 32/37A
Input/Entree: 50Hz,60Hz V 1 Ph A
MFGNo. 44A T12345AA 001 Date: 1404
Hitachi Industrial Equipment
MADE IN JAPAN
NE18238-29
INVERTER
1.1 Inspection of the Purchased Product
1.1.1 Inspecting the product
After unpacking, inspect the product as described below.
If you find the product is abnormal or defective, contact your supplier or local Hitachi Distributor.
(1) Check the product for damage (including falling of parts and dents in the inverter body) caused during
transportation.
(2) Check that the product package contains an inverter set, this Quick Reference Guide and a CD (including the
SJ700D-3 Instruction Manual).
(3) Check the specification label to confirm that the product is the one you have ordered.
Systems Co.,Ltd.
1.1.2 Quick Reference Guide and Instruction Manual
This Quick Reference Guide describes how to handle and maintain the Hitachi SJ700D-3 Series Inverter briefly and
"SJ700D-3 series Instruction Manual" on CD bundled with inverter describes the more detailed information. Read
these manuals carefully before using the inverter, and then keep it handy for those who operate, maintain, and
inspect the inverter. When using the inverter together with optional products, also read the manuals for those
products.
Note that these manuals and the manual for each optional product to be used should be delivered to the end user
of the inverter.
1 - 2
Chapter 1 Overview
1.2 Method of Inquiry and Product Warranty
1.2.1 Method of inquiry
For an inquiry about product damage or faults or a question about the product, notify your supplier of
the following information:
(1) Model of your inverter
(2) Serial number (MFG No.)
(3) Date of purchase
(4) Content of inquiry
- Location and condition of damage
- Content of your question
1.2.2 Product warranty
The product will be warranted under the term described in the next section “1.2.3 Warranty Terms”.
Even within the warranty period, repair of a product fault will not be covered by the warranty (but the repair will be
at your own cost) if:
(1) the fault has resulted from incorrect usage not conforming to the instructions given in this Instruction Manual
or the repair or modification of the product carried out by an unqualified person,
(2) the fault has resulted from a cause not attributable to the delivered product,
(3) the fault has resulted from use beyond the limits of the product specifications, or
(4) the fault has resulted from disaster or other unavoidable events.
The warranty will only apply to the delivered inverter and excludes all damage to other equipment and facilities
induced by any fault of the inverter.
Repair at the user's charge :
Following the warranty period, any examination and repair of the product will be accepted at your charge. Even
during the warranty period, examination and repairs of faults, subject to the above scope of the warranty disclaimer,
will be available at charge. To request a repair at your charge, contact your supplier or local Hitachi Distributor.
1.2.3 Warranty Terms
The warranty period under normal installation and handling conditions shall be two (2) years from the date of
manufacture (“DATE” on product nameplate), or one (1) year from the date of installation, whichever occurs first.
The warranty shall cover the repair or replacement, at Hitachi’s sole discretion, of ONLY the inverter that was
installed.
(1) Service in the following cases, even within the warranty period, shall be charged to the purchaser:
a. Malfunction or damage caused by mis-operation or modification or improper repair
b. Malfunction or damage caused by a drop after purchase and transportation
c. Malfunction or damage caused by fire, earthquake, flood, lightening, abnormal input voltage,
contamination, or other natural disasters
(2) When service is required for the product at your work site, all expenses associated with field repair shall be
charged to the purchaser.
(3) Always keep this manual handy; please do not lose it. Please contact your Hitachi distributor to purchase
replacement or additional manuals.
1 - 3
Chapter 1 Overview
Option slot 1
Main circuit terminals
Backing plate
Control circuit terminals
Option slot 2
POWER lamp
ALARM lamp
Digital operator
Spacer cover
Specification label
Terminal block cover
Front cover
1.3 Exterior Views and Names of Parts
The figure below shows an exterior view of the inverter.
For the wiring of the main circuit and control circuit terminals, open the terminal block cover.
For mounting optional circuit boards, open the front cover.
Exterior view of inverter with the removed front and terminal block covers
Exterior view of inverter
1 - 4
Chapter 2 Installation and Wiring
This chapter describes how to install the inverter and the wiring of main circuit and control
signal terminals with typical examples of wiring.
2.1 Installation ····································· 2 - 2
2.2 Wiring ··········································· 2 - 6
Chapter 2 Installation and Wiring
CAUTION
- Install the inverter on a non-flammable surface, e.g., metal. Otherwise, you run the risk of fire.
- Do not place flammable materials near the installed inverter. Otherwise, you run the risk of fire.
- When carrying the inverter, do not hold its top cover. Otherwise, you run the risk of injury by dropping the
inverter.
- Prevent foreign matter (e.g., cut pieces of wire, sputtering welding materials, iron chips, wire, and dust) from
entering the inverter. Otherwise, you run the risk of fire.
- Install the inverter on a structure able to bear the weight specified in this Instruction Manual. Otherwise, you
run the risk of injury due to the inverter falling.
- Install the inverter on a vertical wall that is free of vibrations. Otherwise, you run the risk of injury due to the
inverter falling.
- Do not install and operate the inverter if it is damaged or its parts are missing. Otherwise, you run the risk of
injury.
- Install the inverter in a well-ventilated indoor site not exposed to direct sunlight. Avoid places where the
inverter is exposed to high temperature, high humidity, condensation, dust, explosive gases, corrosive gases,
flammable gases, grinding fluid mist, or salt water. Otherwise, you run the risk of fire.
- The inverter is precision equipment. Do not allow it to fall or be subject to high impacts, step on it, or place a
heavy load on it. Doing so may cause the inverter to fail.
2.1 Installation
2 - 2
Chapter 2 Installation and Wiring
5 cm or more
5 cm or more
(*1)
(*2)
Inverter
Keep enough clearance between the
inverter and the wiring ducts located
above and below the inverter to prevent
the latter from obstructing the ventilation
of the inverter.
(*1) 10 cm or more : ~ 55kW
(*2) 10 cm or more : ~ 55kW
But for exchanging the DC bus capacitor,
take a distance.
22cm or more : 15kW ~ 55kW
30cm or more : 75kW ~
Inverter
Air flow
Wall
2.1.1 Precautions for installation
(1) Transportation
The inverter uses plastic parts. When carrying the inverter, handle it carefully to prevent damage to the parts.
Do not carry the inverter by holding the front or terminal block cover. Doing so may cause the inverter to fall.
Do not install and operate the inverter if it is damaged or its parts are missing.
(2) Surface on which to install the inverter
The inverter will reach a high temperature (up to about 150°C) during operation. Install the inverter on a vertical
wall surface made of nonflammable material (e.g., metal) to avoid the risk of fire.
Leave sufficient space around the inverter. In particular, keep sufficient distance between the inverter and other
heat sources (e.g., braking resistors and reactors) if they are installed in the vicinity.
(3) Ambient temperature
Avoid installing the inverter in a place where the ambient temperature goes above or below the allowable range
(-10°C to +40°C), as defined by the standard inverter specification.
Measure the temperature in a position about 5 cm distant from the bottom-center point of the inverter, and check
that the measured temperature is within the allowable range.
Operating the inverter at a temperature outside this range will shorten the inverter life (especially the capacitor
life).
(4) Humidity
Avoid installing the inverter in a place where the relative humidity goes above or below the allowable range (20%
to 90% RH), as defined by the standard inverter specification.
Avoid a place where the inverter is subject to condensation.
Condensation inside the inverter will result in short circuits and malfunctioning of electronic parts. Also avoid
places where the inverter is exposed to direct sunlight.
(5) Ambient air
Avoid installing the inverter in a place where the inverter is subject to dust, corrosive gases, combustible gases,
flammable gases, grinding fluid mist, or salt water.
Foreign particles or dust entering the inverter will cause it to fail. If you use the inverter in a considerably dusty
environment, install the inverter inside a totally enclosed panel.
30cm or more : 75kW ~
30cm or more : 75kW ~
2 - 3
Chapter 2 Installation and Wiring
Inverter
Inverter
Enclosure
Horizontal mounting
Inverter
Inverter
Enclosure
Guide
Plate
Vertical mounting
(Unacceptable)
Ventilation fan
Inverter
(Acceptable)
Ventilation fan
Inverter
(6) Installation method and position
Install the inverter vertically and securely with screws or bolts on a surface that is free from vibrations and that
can bear the inverter weight. If the inverter is not installed vertically, its cooling performance may be degraded
and tripping or inverter damage may result.
(7) When mounting multiple inverters in an enclosure with a ventilation fan, carefully design the layout of the
ventilation fan, air intake port, and inverters. An inappropriate layout will reduce the inverter-cooling effect and
raise the ambient temperature. Plan the layout so that the inverter ambient temperature will remain within the
allowable range.
Position of ventilation fan
(8) Mounting in an enclosure
The internal fan releases the heat generated by the inverter from the upper part of the inverter. When it is
necessary to install a device above the inverter, please ensure that the device is protected against this heat.
When several inverters are mounted in the same cabinet the standard arrangement of the inverters is side-by-side
with certain space as shown in the figure on the left below. If the inverters must be mounted one above the other
in order to save the cabinet space or similar, the heat from the lower inverter may lead to temperature rise and
breakdown of the higher inverter. Please ensure that the heat generated by the lower inverter does not affect the
one above by installing a mechanical separation or similar (e.g. guide plate between the inverters as shown in the
figure below right).
When mounting several inverters in the same cabinet, design the cabinet so that the temperature inside the
cabinet does not exceed the allowable specific range for the inverter (by using increased ventilation and/or
enlarging the size of cabinet etc.)
2 - 4
Chapter 2 Installation and Wiring
Section to be cut off
Joint
Inverter capacity (kW)
0.4
0.75
1.5
2.2
3.7/4.0
5.5
7.5
11
15
18.5
Loss with 70% load (W)
64
76
102
127
179
242
312
435
575
698
Loss with 100% load (W)
70
88
125
160
235
325
425
600
800
975
Efficiency at rated output (%)
85.1
89.5
92.3
93.2
94.0
94.4
94.6
94.8
94.9
95.0
Inverter capacity (kW)
22
30
37
45
55
75
90
110
132/150
Loss with 70% load (W)
820
1100
1345
1625
1975
2675
3375
3900
4670
Loss with 100% load (W)
1150
1550
1900
2300
2800
3800
4800
5550
6650
Efficiency at rated output (%)
95.0
95.0
95.1
95.1
95.1
95.2
95.2
95.2
95.2
Backing plate
Rubber bushing
(9) Reduction of enclosure size
If you mount the inverter inside an enclosure such that the heat sink of the inverter is positioned outside the
enclosure, the amount of heat produced inside the enclosure can be reduced and likewise the size of the
enclosure. Mounting the inverter in an enclosure with the heat sink positioned outside requires an optional
dedicated special metal fitting. To mount the inverter in an enclosure with the heat sink positioned outside, cut
out the enclosure panel according to the specified cutting dimensions. The cooling section (including the heat
sink) positioned outside the enclosure has a cooling fan. Therefore, do not place the enclosure in any
environment where it is exposed to waterdrops, oil mist, or dust.
(10) Approximate loss by inverter capacity
2.1.2 Backing plate
(1) For models with 30 kW or less capacity
On the backing plate, cut the joints around each section to be cut off with cutting pliers or a cutter, remove them,
and then perform the wiring.
(2) For the models with 37 kW to 75kW
1) For wiring without using conduits
Cut an X in each rubber bushing of the backing plate with cutting pliers or a cutter, and then perform the wiring.
2) For wiring using conduits
Remove the rubber bushings from the holes to be used for wiring with conduits, and then fit conduits into the
holes.
Note: Do not remove the rubber bushing from holes that are not used for wiring with a conduit.
If a cable is connected through the plate hole without a rubber bushing and conduit, the cable insulation
may be damaged by the edge of the hole, resulting in a short circuit or ground fault.
2 - 5
Chapter 2 Installation and Wiring
WARNING
- Be sure to ground the inverter. Otherwise, you run the risk of electric shock or fire.
- Commit wiring work to a qualified electrician. Otherwise, you run the risk of electric shock or fire.
- Before wiring, make sure that the power supply is off. Otherwise, you run the risk of electric shock or fire.
- Perform wiring only after installing the inverter. Otherwise, you run the risk of electric shock or injury.
- Do not remove rubber bushings from the wiring section. Otherwise, the edges of the wiring cover may damage
the wire, resulting in a short circuit or ground fault.
CAUTION
- Make sure that the voltage of AC power supply matches the rated voltage of your inverter. Otherwise, you run
the risk of injury or fire.
- Do not input single-phase power into the inverter. Otherwise, you run the risk of fire.
- Do not connect AC power supply to any of the output terminals (U, V, and W). Otherwise, you run the risk of
injury or fire.
- Do not connect a resistor directly to any of the DC terminals (PD, P, and N). Otherwise, you run the risk of fire.
- Connect an earth-leakage breaker to the power input circuit. Otherwise, you run the risk of fire.
- Use only the power cables, earth-leakage breaker, and magnetic contactors that have the specified capacity
(ratings). Otherwise, you run the risk of fire.
- Do not use the magnetic contactor installed on the primary and secondary sides of the inverter to stop its
operation.
- Tighten each screw to the specified torque. No screws must be left loose. Otherwise, you run the risk of fire.
- Before operating, slide switch SW1 in the inverter, be sure to turn off the power supply. Otherwise, you run the
risk of electric shock and injury.
- Since the inverter supports two modes of cooling-fan operation, the inverter power is not always off, even when
the cooling fan is stopped. Therefore, be sure to confirm that the power supply is off before wiring. Otherwise,
you run the risk of electric shock and injury.
2.2 Wiring
2 - 6
Chapter 2 Installation and Wiring
3-phase power supply
(50/60 Hz ±5%)
Jumper
When connecting separate power
cables beforehand.
Power supply for
control circuit
Forward rotation
Intelligent input
Digital monitor output
(PWM output)
Thermistor
Frequency
500 to 2,000Ω
0 to 10 VDC (12 bits)
-10 to +10 VDC (12 bits)
4 to 20 mA (12 bits)
Analog monitor
Analog monitor
0 to 10 V (10 bits)
4 to 20 mA (10 bits)
Motor
Jumper bar
Braking resistor
The dotted line indicates
terminal board.
Intelligent relay output contact
Intelligent output
For terminating
resistor
Option 1
Option 2
Type-D grounding (for 200 V class model)
(See page 2-12.)
PLC
P24
DC24V
CM
R S T
R0
T0 U V
W
PD
P
RB
N
FW
7
6
1
8
FM
CM1
H
O
O2
OI
L
AM
AMI
SP
SN
RP
SN
RS485
AL0
AL1
AL2
1
2
HITACHI
POWER
ALARM
Hz
V
A
%
kW
RUN
PRG
RUN
FUNC
STR
DC10V
100Ω
10kΩ
10kΩ
15
11
CM2
R
T
TH
J51
STOP/
RESET
M
100Ω
Default jumper position
(source type : FEF)
DCL
(without jumper bar)
BRD
2.2.1 Terminal connection diagram and explanation of terminals and switch settings
200 V class: 200 to 240 V +10%, -15%
(50/60 Hz ±5%)
400 V class: 380 to 480 V +10%, -15%
supplies to main and control
circuits, remove J51 connector
(sinking type : FUF/FF)
Default jumper position
(Models with 22kW
or less capacity )
the detachable control
command
(8 contacts)
setting circuit
(default: alarm output)
(5 terminals)
output
(voltage output)
output
(current output)
Type-C grounding (for 400 V class model)
2 - 7
Chapter 2 Installation and Wiring
Symbol
Terminal name
Description
R, S, T
(L1, L2, L3)
Main power input
Connect to the AC power supply.
Leave these terminals unconnected when using a regenerative converter (HS900 series).
U, V, W
(T1, T2, T3)
Inverter output
Connect a 3-phase motor.
PD, P
(+1, +)
DC reactor connection
Remove the jumper from terminals PD and P, and connect the optional power factor reactor (DCL).
P, RB
(+, RB)
External braking resistor
connection
Connect the optional external braking resistor.
(The RB terminal is provided on models with 30 kW or less capacity.)
P, N
(+, -)
Regenerative braking unit
connection
Connect the optional regenerative braking unit (BRD).
G
Inverter ground
Connect to ground for grounding the inverter chassis by type-D grounding (for 200 V class models)
or type-C grounding (for 400 V class models).
Symbol
Terminal name
Description
Electric property
Analog
Power
supply
L
Analog power
supply (common)
This common terminal supplies power to frequency command terminals (O, O2,
and OI) and analog output terminals (AM and AMI). Do not ground this terminal.
H Frequency setting
power supply
This terminal supplies 10 VDC power to the O, O2, OI terminals.
Allowable load current:
20 mA or less
Frequency setting input
O
Frequency
command
(voltage)
Input a voltage (0 to 10 VDC) as a frequency command. 10 V specifies the
maximum frequency.
To specify the maximum frequency with a voltage of 10 V or less, set the voltage
using function "A014".
Input impedance: 10kΩ
Allowable input voltages: -0.3
to +12 VDC
O2
Auxiliary
frequency
command
(voltage)
Input a voltage (0 to ±10 VDC) as a signal to be added to the frequency command
input from the O or OI terminal. You can input an independent frequency
command from this terminal (O2 terminal) alone by changing the setting.
Input impedance: 10kΩ
Allowable input voltages:
0 to 12 VDC
OI
Frequency
command
(current)
Input a current (4 to 20 mA DC) as a frequency command. 20 mA specifies the
maximum frequency.
The OI signal is valid only when the AT signal is on. Assign the AT function to an
intelligent input terminal.
Input impedance: 10kΩ
Maximum allowable current:
24 mA
Monitor output
AM
Analog monitor
(voltage)
This terminal outputs one of the selected "0 to 10 VDC voltage output"
monitoring items. The monitoring items available for selection include output
frequency, output current, output torque (signed or unsigned), output voltage,
input power, electronic thermal overload, LAD frequency, motor temperature,
heat sink temperature, and general output.
Maximum allowable current:
2 mA
Output voltage accuracy
±20%
(Ta=25±10 degrees C)
AMI
Analog monitor
(current)
This terminal outputs one of the selected "4 to 20 mA DC current output"
monitoring items. The monitoring items available for selection include output
frequency, output current, output torque (unsigned), output voltage, input power,
electronic thermal overload, LAD frequency, motor temperature, heat sink
temperature, and general output.
Allowable load impedance:
250Ω or less
Output current accuracy
±20%
(Ta=25±10 degrees C)
Digital (contact)
Monitor output
FM
Digital monitor
(voltage)
This terminal outputs one of the selected "0 to 10 VDC voltage output (PWM
output mode)" monitoring items. The monitoring items available for selection
include output frequency, output current, output torque (unsigned), output voltage,
input power, electronic thermal overload, LAD frequency, motor temperature,
heat sink temperature, general output, digital output frequency, and digital current
monitor.
For the items "digital output frequency" and "digital current monitor," this
terminal outputs a digital pulse signal at 0/10 VDC with a duty ratio of 50%.
Maximum allowable current:
1.2 mA
Maximum frequency:
3.6 kHz
Power supply
P24
Interface power
supply
This terminal supplies 24 VDC power for contact input signals.
If the source logic is selected, this terminal is used as a common contact input
terminal.
Maximum allowable output
current: 100 mA
CM1
Interface power
supply (common)
This common terminal supplies power to the interface power supply (P24),
thermistor input (TH), and digital monitor (FM) terminals. If the sink logic is
selected, this terminal is used as a common contact input terminal. Do not ground
this terminal.
Contact input
Operation
command
FW
Forward rotation
command
Turn on this FW signal to start the forward rotation of the motor; turn it off to stop
forward rotation after deceleration.
[Conditions for turning
contact input on]
Voltage across input and PLC:
18 VDC or more
Input impedance between
input and PLC: 4.7kΩ
Maximum allowable voltage
across input and PLC:
27 VDC
Load current with 27 VDC
power: about 5.6 mA
Function selection and logic
switching
1
2
3
4
5
6
7
8
Intelligent input
Select eight of a total 56 functions, and assign these eight functions to terminals 1
to 8.
Note:
If the emergency stop function is used, terminals 1 and 3 are used exclusively for
the function. For details, refer to the SJ700D-3 instruction manual.
(1) Explanation of main circuit terminals
(2) Explanation of control circuit terminals
2 - 8
Chapter 2 Installation and Wiring
Symbol
Terminal name
Description
Electric property
Digital (contact)
Contact input
Function selection and
logic switching
PLC
Intelligent input
(common)
To switch the control logic between sink logic and source logic, change the
jumper connection of this (PLC) terminal to another terminal on the control
circuit terminal block.
Jumper terminals P24 and PLC for the sink logic; jumper terminals CM1 and PLC
for the sink logic.
To use an external power supply to drive the contact inputs, remove the jumper,
and connect the PLC terminal to the external interface circuit.
Open collector
output
Status and factor
11
12
13
14
15
Intelligent output
Select five of a total 51 functions, and assign these five functions to terminals 11
to 15.
If you have selected an alarm code using the function "C062", terminals 11 to 13
or 11 to 14 are used exclusively for the output of cause code for alarm (e.g.,
inverter trip). The control logic between each of these terminals and the CM2
terminal always follows the sink or source logic.
Voltage drop between each
terminal and CM2 when
output signal is on: 4 V or less
Maximum allowable voltage:
27 VDC
Maximum allowable current:
50 mA
CM2
Intelligent output
(common)
This terminal serves as the common terminal for intelligent output terminals [11]
to [15].
Relay contact output
Status and alarm
AL0
AL1
AL2
Intelligent relay
output
Select functions from the 43 available, and assign the selected functions to these
terminals, which serve as C contact output terminals.
In the initial setting, these terminals output an alarm indicating that the inverter
protection function has operated to stop inverter output.
(Maximum contact capacity)
AL1-AL0: 250 VAC, 2 A
(resistance) or 0.2 A
(inductive load)
AL2-AL0: 250 VAC, 1 A
(resistance) or 0.2 A
(inductive load)
(Minimum contact capacity)
100 VAC, 10 mA
5 VDC, 100 mA
Analog
Analog input
Sensor
TH
External
thermistor input
Connect to an external thermistor to make the inverter trip if an abnormal
temperature is detected.
The CM1 terminal serves as the common terminal for this terminal.
[Recommended thermistor properties]
Allowable rated power: 100 mW or more
Impedance at temperature error: 3kΩ
The impedance to detect temperature errors can be adjusted within the range 0Ω
to 9,999Ω.
Allowable range of input
voltages
0 to 8 VDC
[Input circuit]
DC8V
10kΩ
1kΩ
CM1
TH
Thermistor
ＯＮ
Slide switch SW1
OFF
ON
Slide lever (factory setting: OFF)
(3) Explanation of switch
In case of using the emergency stop function*, you need to set the SW1 to “ON”. Refer to the SJ700D-3 manuals
for more information.
* This function does not comply with any functional safety norm.
*) Do not change the other switch, which is intended
for factory adjustment
2 - 9
Chapter 2 Installation and Wiring
washer of the terminal screw
2.2.2 Wiring of the main circuit
(1) Wiring instructions
Before wiring, be sure to confirm that the Charge lamp on the inverter is turned off. When the inverter power has
been turned on once, a dangerous high voltage remains in the internal capacitors for some time after power-off,
regardless of whether the inverter has been operated. When rewiring after power-off, always wait 10 minutes or
more after power-off, and check with a multimeter that the residual voltage across terminals P and N is zero to
ensure safety during rewiring work.
(note) As for the 5.5kW and 7.5kW inverters, the washer on the main terminal screw (R, S, T, PD, P, N, U, V, W,
RB) has two cutouts. Since those cutouts are to avoid the cable fixing portion of crimp terminal goes
under the washer, it should be fixed in direction with those two cutouts in line with cable as described
below. Otherwise, you run the risk of loose connection and fire.
1) Main power input terminals (R, S, and T)
- Install an earth-leakage breaker for circuit (wiring) protection between the power supply and main power
input terminals (R, S, and T).
- Use an earth-leakage breaker with a high rating of a high-frequency sensitive current to prevent the breaker
from malfunctioning under the influence of high frequency.
- When the protective function of the inverter operates, a fault or accident may have occurred in your system.
Therefore, you are recommended to connect a magnetic contactor that interrupts the power supply to the
inverter.
- Do not use the magnetic contactor connected to the power input terminal (primary side) or power output
terminal (secondary side) of the inverter to start or stop the inverter. To start and stop inverter operation by
external signals, use only the operation commands (FW and RV signals) that are input via control circuit
terminals.
- This inverter does not support a single-phase input but supports only a three-phase input.
If you need to use a single-phase power input, contact your supplier or local Hitachi Distributor.
- Do not operate the inverter when an input phase is lost (input phase loss), otherwise the inverter may be
damaged. Since the factory setting of the inverter disables the phase loss input protection, the inverter will go
into the following status if a phase of power supply input is interrupted and not supplied to the inverter:
R or T phase interrupted: The inverter does not power up.
S phase interrupted: The inverter goes into single-phase operation, and may trip because of insufficient
voltage or overcurrent, or be damaged.
Internal capacitors remain charged, even when the power input is under a phase loss condition. Therefore,
touching an internal part may result in electric shock and injury.
When rewiring the main circuit, follow the instructions given in Item (1), "Wiring instructions."
- Carefully note that the internal converter module of the inverter may be damaged if:
- The imbalance of power voltage is 3% or more,
- The power supply capacity is at least 10 times as high as the inverter capacity and 500 kVA or more, or
- The power voltage changes rapidly.
Example: The above conditions may occur when multiple inverters are connected to each other by a short bus
line or your system includes a phase-advanced capacitor that is turned on and off during operation.
- Do not turn the inverter power on and off more often than once every 3 minutes. Otherwise, the inverter may
be damaged.
2 - 10
Chapter 2 Installation and Wiring
Remove the jumper only when connecting the DCL. If the jumper is removed and the DCL is not
connected, power is not supplied to the main circuit of the inverter, and the inverter cannot operate.
Inverter
Inverter
Inverter
Grounding bolt
prepared by user
Inverter
Inverter
Inverter
2) Inverter output terminals (U, V, and W)
- Use a cable thicker than the specified applicable cable for the wiring of output terminals to prevent the output
voltage between the inverter and motor dropping. Especially at low frequency output, a voltage drop due to
cable will cause the motor torque to decrease.
- Do not connect a phase-advanced capacitor or surge absorber on the output side of the inverter. If connected,
the inverter may trip or the phase-advanced capacitor or surge absorber may be damaged.
- If the cable length between the inverter and motor exceeds 20 m (especially in the case of 400 V class models),
the stray capacitance and inductance of the cable may cause a surge voltage at motor terminals, resulting in a
motor burnout. A special filter to suppress the surge voltage is available. If you need this filter, contact your
supplier or local Hitachi Distributor.
- When connecting multiple motors to the inverter, connect a thermal relay to the inverter output circuit for
each motor.
- The RC rating of the thermal relay must be 1.1 times as high as the rated current of the motor. The thermal
relay may go off too early, depending on the cable length. If this occurs, connect an AC reactor to the output
of the inverter.
3) DC reactor connection terminals (PD and P)
- Use these terminals to connect the optional DC power factor reactor (DCL). As the factory setting, terminals P
and PD are connected by a jumper. Remove this to connect the DCL.
- The cable length between the inverter and DCL must be 5 m or less.
4) External braking resistor connection terminals (P and RB) and regenerative braking unit connection terminals
(P and N)
- Inverter models with 22 kW or less capacity have a built-in regenerative braking (BRD) circuit. If you need
increased braking performance, connect an optional external braking resistor to terminals P and RB. Do not
connect an external braking resistor with resistance less than the specified value. Such a resistor may cause
damage to the regenerative braking (BRD) circuit.
- Inverter models with capacity of 30 kW or more do not have a built-in regenerative braking (BRD) circuit.
Increasing the braking performance of these models requires an optional regenerative braking unit and an
external braking resistor. Connect the P and N terminals of the optional regenerative braking unit to the P and
N terminals of the inverters.
- The cable length between the inverter and optional regenerative braking unit must be 5 m or less, and the two
cables must be twisted for wiring.
- Do not use these terminals for connecting any devices other than the optional external braking resistor and
regenerative braking unit.
5) Inverter ground terminal (G )
- Be sure to ground the inverter and motor to prevent electric shock.
- According to the Electric Apparatus Engineering Regulations, connect 200 V class models to grounding
electrodes constructed in compliance with type-D grounding (conventional type-III grounding with ground
resistance of 100Ω or less) or the 400 V class models to grounding electrodes constructed in compliance with
type-C grounding (conventional special type-III grounding with ground resistance of 10Ω or less).
- Use a grounding cable thicker than the specified applicable cable, and make the ground wiring as short as
possible.
- When grounding multiple inverters, avoid a multi-drop connection of the grounding route and formation of a
ground loop, otherwise the inverter may malfunction.
2 - 11
Chapter 2 Installation and Wiring
Terminal layout
Inverter model
SJ700D-004-037LFF3
SJ700D-007-037HFF3
R0 and T0: M4
Ground terminal: M4
Other terminals: M4
Enabling PIN(J61)
Disabling PIN(J62)
EMC filter disables
(factory setting)
Dummy plug (green)
Short plug
EMC filter enables
Short plug
Dummy plug (green)
If you need to activate the
EMC filter, you need to set
the dummy plug and the
short plug in reference to
below list appropriately.
Note:
Before setting the plugs,
make sure that the power
supply is off. Otherwise, you
run the risk of electric shock.
You need to set the plugs
before power supply to the
inverter.
Dummy plug (green)
Enabling PIN(J61)
Short plug
Disabling PIN(J62)
R
(L1) S (L2) T (L3)
PD
(+1) P (+) N U
(T1) V (T2) W (T3)
R0
T0
Charge lamp
Jumper connecting terminals PD and P
When not using the DCL,
do not remove the jumper
from terminals PD and P.
G
G
RB
(-)
[Method of enabling/disabling the EMC filter function]
(2) Layout of main circuit terminals
The figures below show the terminal layout on the main circuit terminal block of the inverter.
2 - 12
Chapter 2 Installation and Wiring
Terminal layout
Inverter model
SJ700D-055，075LFF3
SJ700D-055，075HFF3
R0 and T0: M4
Ground terminal: M5
Other terminals: M5
SJ700D-110LFF3
SJ700D-110HFF3
R0 and T0: M4
Ground terminal: M5
Other terminals: M6
SJ700D-150 to 185 LFF3
SJ700D-150 to 220 HFF3
R0 and T0: M4
Ground terminal: M6
Other terminals: M6
SJ700D-220LFF3
R0 and T0: M4
Ground terminal: M6
Other terminals: M8
[Method of enabling/disabling the EMC filter function]
Enabling the EMC filter
Disabling the EMC filter
(factory setting)
Disabling the EMC filter
(factory setting)
[Method of enabling/disabling the EMC filter function]
Enabling the EMC filter
R
(L1) S (L2) T (L3)
PD
(+1) P (+) N U
(T1) V (T2) W (T3)
Charge lamp
Jumper connecting
terminals PD and P
When not using the DCL,
do not remove the jumper
from terminals PD and P.
G
G
RB
(-)
R0
T0
Ground terminal with jumper (shaded in the figure) to
enable/disable the EMC filter function.
R
(L1) S (L2) T (L3)
PD
(+1)
P
(+)
N U (T1) V (T2) W (T3)
Charge lamp
Jumper connecting
terminals PD and P
When not using the DCL,
do not remove the jumper
from terminals PD and P.
G
G
RB
(-)
R0
T0
Ground terminal with jumper (shaded in the figure) to
enable/disable the EMC filter function
2 - 13
Chapter 2 Installation and Wiring
Terminal layout
Inverter model
SJ700D-300LFF3
R0 and T0: M4
Ground terminal: M6
Other terminals: M8
SJ700D-300HFF3
R0 and T0: M4
Ground terminal: M6
Other terminals: M6
SJ700D-370LFF3
SJ700D-370HFF3
R0 and T0: M4
Ground terminal: M8
Other terminals: M8
SJ700D-450LFF3
SJ700D-450HFF3
SJ700D-550HFF3
R0 and T0: M4
Ground terminal: M8
Other terminals: M8
R
(L1) S (L2) T (L3)
PD
(+1)
P (+N
U
(T1)
V
(T2)
W
(T3)
Charge lamp
Jumper connecting
terminals PD and P
G
G
(-)
R0
T0
Ground terminal with jumper (shaded in the figure) to
enable/disable the EMC filter function
When not using the DCL,
do not remove the jumper
from terminals PD and P.
[Method of enabling/disabling the EMC filter function]
Enabling the EMC filter
Disabling the EMC filter
(factory setting)
[Method of enabling/disabling the EMC filter function]
Enabling the EMC filter
Disabling the EMC filter
(factory setting )
R
(L1) S (L2) T (L3)
PD
(+1)
P
(+)
N U (T1) V (T2) W (T3)
Charge lamp
Jumper connecting
terminals PD and P
G
G
(-)
R0
T0
Ground terminal with jumper (shaded in the figure) to
enable/disable the EMC filter function
When not using the DCL,
do not remove the jumper
from terminals PD and P.
G
2 - 14
Chapter 2 Installation and Wiring
Terminal layout
Inverter model
SJ700D-550LFF3
R0 and T0: M4
Ground terminal: M8
Other terminals: M10
SJ700D750 to 1320 HFF3
R0 and T0:M4
Ground terminal:M8
Other terminal:M10
200 V class model (input power: 200 VAC, 50 Hz)
400 V class model (input power: 400 VAC, 50 Hz)
0.4kW
to 3.7kW
5.5kW
to 11kW
15kW
to 37kW
45kW
to 55kW
0.75kW
to 3.7kW
5.5kW
to11kW
15kW
to 37kW
45kW
to 55kW
75kW to
150kW
Internal EMC filter enabled
Ca. 2.5mA
Ca. 48mA
Ca. 23mA
Ca. 23mA
Ca. 5mA
Ca. 95mA
Ca 56mA
Ca 56mA
-
Internal EMC filter disabled
Ca. 0.1mA
Ca. 0.1mA
Ca. 0.1mA
Ca. 0.1mA
Ca. 0.2mA
Ca. 0.2mA
Ca 0.2mA
Ca. 0.2mA
Ca. 0.2mA
[Method of enabling/disabling the EMC filter function]
Enabling the EMC filter
Disabling the EMC filter
(factory setting)
R0
T0
Jumper connecting terminals
PD and P
Charge lump
R
(L1) S (L2) T (L3)
PD
(+1) P (+N U
(T1)
V
(T2) W (T3)
Charge lamp
Jumper connecting
terminals PD and P
G
G
(-)
Ground terminal with jumper (shaded in the figure) to
enable/disable the EMC filter function
When not using the DCL,
do not remove the jumper
from terminals PD and P.
G
R
(L1) S (L2) T (L3)
Reference: Leakage current by inverter with model EMC filter enabled or disabled (reference data). The table below lists the reference currents
that may leak from the inverter when the internal EMC filter is enabled or disabled. (Leakage current is in proportion to the voltage and
frequency of input power.) Note that the values listed in the table below indicate the reference currents leaking from the inverter alone. The
values exclude current leakage from external devices and equipment (e.g., power cables). The drive in the range from 75kW to 150kW doesn't
have the switch to activate and deactivate the internal EMC filter. They complies EMC directive C3 level in standard condition.
PD
(+1) P (+) N (-) U (T1) V (T2) W (T3)
2 - 15
Chapter 2 Installation and Wiring
Total cable length
Sensitivity current (mA)
100 m or less
50
300 m or less
100
Name
Description
Reactor on input side (for
harmonic control, power supply
coordination, and power factor
improvement)
(ALI-XXX)
Use this reactor to control harmonic waves or when the imbalance
of power supply voltage is 3% or more, when the power supply
capacity is 500 kVA or more, or when the power voltage may
change rapidly. This reactor also improves the power factor.
Noise filter for inverter
(NF-XXX)
This noise filter reduces the conductive noise that is generated by
the inverter and transmitted in cables. Connect this noise filter to the
primary side (input side) of the inverter.
Radio noise filter
(Zero-phase reactor) (ZCL-X)
The inverter may generate radio noise through power supply wiring
during operation. Use this noise filter to reduce the radio noise
(radiant noise).
Radio noise filter on input side
(Capacitor filter) (CFI-X)
Use this noise filter to reduce the radiant noise radiated from input
cables.
DC reactor (DCL-X-XX)
Use this reactor to control the harmonic waves generated by the
inverter.
Braking resistor
Regenerative braking unit
Use these devices to increase the braking torque of the inverter for
operation in which the inverter turns the connected load on and off
very frequently or decelerates the load running with a high moment
of inertia.
Noise filter on the output side
(ACF-CX)
Connect this noise filter between the inverter and motor to reduce
the radiant noise radiated from cables for the purpose of reducing
the electromagnetic interference with radio and television reception
and preventing malfunctions of measuring equipment and sensors.
Radio noise filter
(Zero-phase reactor)
(ZCL-XXX)
Use this noise filter to reduce the noise generated on the output side
of the inverter. (This noise filter can be used on both the input and
output sides.)
AC reactor for the output side
For reducing vibrations and
preventing thermal relay
malfunction
(ACL-X-XX)
Using the inverter to drive a general-purpose motor may cause
larger vibrations of the motor when compared with driving it
directly with the commercial power supply. Connect this AC reactor
between the inverter and motor to lessen the pulsation of motor.
Also, connect this AC reactor between the inverter and motor, when
the cable length between them is long (10 m or more), to prevent
thermal relay malfunction due to the harmonic waves that are
generated by the switching operation on the inverter. Note that the
thermal relay can be replaced with a current sensor to avoid the
malfunction.
LCR filter
Connect this noise filter between the inverter and motor to convert
the inverter output into a sinusoidal waveform and to reduce the
motor vibration, motor noise and the radiant noise radiated from
cables.
R S T
R0
T0
Inverter
Power
supply
ELB
Magnetic
contactor
U V W
PD P N
Motor
M
RB
(3) Applicable peripheral equipment
See Item (4), "Recommended cable gauges, wiring accessories, and crimp terminals."
Note 1: The peripheral equipment described here is applicable when the inverter connects a
Note 2: Select breakers that have proper capacity. (Use breakers that comply with inverters.)
Note 3: Use earth-leakage breakers (ELB) to ensure safety.
Note 4: Use copper electric wire (HIV cable) of which the maximum allowable temperature of
Note 5: If the power line exceeds 20 m, cable that is thicker than the specified applicable cable
Note 6: Use a 0.75 mm2 cable to connect the alarm output contact.
Note 7: Tighten each terminal screw with the specified tightening torque. Loose terminal
Note 8: Select an earth-leakage breaker (ELB) of which the rated sensitivity current matches
Note 9: When a CV cable is used for wiring through a metal conduit, the average current
Note 10: When an IV cable, which has a high relative dielectric constant, is used, the leakage
standard Hitachi 3-phase, 4-pole squirrel-cage motor.
the insulation is 75°C.
must be used for the power line.
screws may cause short circuits and fire. Tightening a terminal screw with excessive
torque may cause damage to the terminal block or inverter body.
the total length of cables connected between the inverter and power supply and
between the inverter and motor. Do not use a high-speed type ELB but use a
delayed-type ELB because the high-speed type may malfunction.
leakage is 30 mA/km.
current is about eight times as high as the standard cable. Therefore, when using an IV
cable, use the ELB of which the rated sensitivity current is eight times as high as that
given in the table below. If the total cable length exceeds 100 m, use a CV cable.
2 - 16
Chapter 2 Installation and Wiring
Motor
output
(kW)
Applicable
inverter model
Gauge of
power line
cable (mm2)
(Terminals:
R, S, T, U, V,
W, P, PD, and
N)
Grounding
cable
(mm2)
External
braking resistor
across terminals
P and RB (mm2)
Size of
terminal
screw
Crimp
termin
al
Tightening
torque (N-m)
Applicable device
Earth-leakage
breaker (ELB)
Magnetic
contactor
(MC)
200 V class
0.4
SJ700D-004L***3
1.25
1.25
1.25
M4
1.25-4
1.2(MAX1.8)
EX50B(5A)
HS10
0.75
SJ700D-007L***3
1.25
1.25
1.25
M4
1.25-4
1.2(MAX1.8)
EX50B(10A)
HS10
1.5
SJ700D-015L***3
2 2 2
M4
2-4
1.2(MAX1.8)
EX50B(15A)
HS10
2.2
SJ700D-022L***3
2 2 2
M4
2-4
1.2(MAX1.8)
EX50B(20A)
HS20
3.7
SJ700D-037L***3
3.5
3.5
3.5
M4
3.5-4
1.2(MAX1.8)
EX50B(30A)
HS20
5.5
SJ700D-055L***3
5.5
5.5
5.5
M5
R5.5-5
2.4(MAX4.0)
EX50B(50A)
HS25
7.5
SJ700D-075L***3
8 8 8
M5
R8-5
2.4(MAX4.0)
EX60(60A)
HS35
11
SJ700D-110L***3
14
14
14
M6
R14-6
4.0(MAX4.4)
RXK100-H(75A)
HS50
15
SJ700D-150L***3
22
22
22
M6
22-6
4.5(MAX4.9)
RXK100-H(100A)
H65C
18.5
SJ700D-185L***3
30
22
30
M6
38-6
4.5(MAX4.9)
RXK100-H(100A)
H80C
22
SJ700D-220L***3
38
30
38
M8
38-8
8.1(MAX8.8)
RXK225-H(150A)
H100C
30
SJ700D-300L***3
60(22×2)
30 ― M8
60-8
8.1(MAX8.8)
RXK225-H(200A)
H125C
37
SJ700D-370L***3
100(38×2)
38 ― M8
100-8
8.1(MAX20)
RXK225-H(225A)
H150C
45
SJ700D-450L***3
100(38×2)
38 ― M8
100-8
8.1(MAX20)
RXK225-H(225A)
H200C
55
SJ700D-550L***3
150(60×2)
60 ― M10
150-10
19.5(MAX22)
RX400B(350A)
H250C
400 V class
0.75
SJ700D-007H***3
1.25
1.25
1.25
M4
1.25-4
1.2(MAX1.8)
EX50C(5A)
HS10
1.5
SJ700D-015H***3
2 2 2
M4
2-4
1.2(MAX1.8)
EX50C(10A)
HS10
2.2
SJ700D-022H***3
2 2 2
M4
2-4
1.2(MAX1.8)
EX50C(10A)
HS10
3.7
SJ700D-037H***3
2 2 2
M4
2-4
1.2(MAX1.8)
EX50C(15A)
HS20
5.5
SJ700D-055H***3
3.5
3.5
3.5
M5
R2-5
2.4(MAX4.0)
EX50C(30A)
HS20
7.5
SJ700D-075H***3
3.5
3.5
3.5
M5
3.5-5
2.4(MAX4.0)
EX50C(30A)
HS25
11
SJ700D-110H***3
5.5
5.5
5.5
M6
R5.5-6
4.0(MAX4.4)
EX50C(50A)
HS35
15
SJ700D-150H***3
8 8 8
M6
8-6
4.5(MAX4.9)
EX60B(60A)
HS35
18.5
SJ700D-185H***3
14
14
14
M6
14-6
4.5(MAX4.9)
EX60B(60A)
HS50
22
SJ700D-220H***3
14
14
14
M6
14-6
4.5(MAX4.9)
RXK100-H(75A)
HS50
30
SJ700D-300H***3
22
22 ― M6
22-6
4.5(MAX4.9)
RXK100-H(100A)
H65C
37
SJ700D-370H***3
38
22 ― M8
38-8
8.1(MAX20)
RXK100-H(100A)
H80C
45
SJ700D-450H***3
38
22 ― M8
38-8
8.1(MAX20)
RXK225-H(150A)
H100C
55
SJ700D-550H***3
60
30 ― M8
R60-8
8.1(MAX20)
RXK225-H(175A)
H125C
75
SJ700D-750H***3
100(38×2)
38 ― M10
100-10
20.0(MAX22)
RXK225-H(225A)
H150C
90
SJ700D-900H***3
100(38×2)
38 ― M10
100-10
20.0(MAX22)
RXK225-H(225A)
H200C
110
SJ700D-1100H***3
150(60×2)
60 ― M10
150-10
20.0(MAX35)
RX400B(350A)
H250C
132
SJ700D-1320HFF3
SJ700D-1320HFEF3
80×2
80 ― M10
80-10
20.0(MAX35)
RX400B(350A)
H300C
150
SJ700D-1320HFF3
80×2
80 ― M10
80-10
20.0(MAX35)
RX400B(350A)
H300C
(4) Recommended cable gauges, wiring accessories, and crimp terminals
Note: For compliance with CE and UL standards, see the safety precautions concerning EMC and the
compliance with UL and cUL standards under Safety Instructions.
The table below lists the specifications of cables, crimp terminals, and terminal screw tightening torques
for reference.
Note: Cable gauges indicate those of HIV cables (maximum heat resistance: 75°C).
Note: *** is described as FF, FEF or FUF.
Note: Please use the round type crimp terminals (for the UL standard) suitable for the use electric wire when you connect the
electric wire with the main circuit terminal stand. Please put on pressure to the crimp terminals l with a crimp tool that the
terminal stand maker recommends.
2 - 17
Chapter 2 Installation and Wiring
2. Remove the J51 connector.
1. Remove the connected cables.
3. Connect the control circuit power
supply cables to the control circuit
power supply terminal block.
J51
(5) Connecting the control circuit to a power supply separately from the main circuit.
If the protective circuit of the inverter operates to open the magnetic contactor in the input power supply circuit,
the inverter control circuit power is lost, and the alarm signal cannot be retained. To retain the alarm signal,
connect control circuit terminals R0 and T0 to a power supply. In details, connect the control circuit power
supply terminals R0 and T0 to the primary side of the magnetic contactor as shown below.
(Connection method)
Power-receiving specifications
200 V class model:
200 to 240 V (+10%, -15%)
(50/60 Hz ±5%), (282 to 339 VDC)
400 V class model:
380 to 480 V (+10%, -15%)
(50/60 Hz ±5%), (537 to 678 VDC)
Note the following when connecting separate power supplies to control circuit power supply terminals (R0 and T0) and
main circuit power supply terminals (R, S, and T):
- Use a cable thicker than 1.25 mm2 to connect the terminals R0 and T0 (terminal screw size: M4).
- Connect a 3A fuse in the control circuit power supply line. (Tightening torque: 1.2Nm,max torque: 1.4Nm)
- If the control circuit power supply (connected to R0 and T0) is turned on earlier than the main circuit power supply
(connected to R, S, and T), ground fault is not checked at power-on.
- When supplying DC power to the control circuit power supply terminals (R0 and T0), specify "00" as the "a/b (NO/NC)"
selection (function code C031 to C036) for intelligent output terminals ([11] to [15]) and intelligent relay terminals (AL0,
AL1, and AL2). If "01" is specified as the "a/b (NO/NC)" selection, output signals may chatter when the DC power supply
is shut off.
2 - 18
Chapter 2 Installation and Wiring
H O2
AM
FM
TH
FW 8 CM1 5 3 1 14
13
11
AL1
L O OI
AMI
P24
PLC
CM1 7 6 4 2
15
CM2
12
AL0
AL2
TH
PLC
CM1
7
6
CM1
8
FW
Thermistor
PLC
5
4
2.2.3 Wiring of the control circuit
(1) Wiring instructions
1) Terminals L and CM1 are common to I/O signals and isolated from each other.
Do not connect these common terminals to each other or ground them.
Do not ground these terminals via any external devices. (Check that the external devices connected to these
terminals are not grounded.)
2) Use a shielded, twisted-pair cable (recommended gauge: 0.75 mm2) for connection to control circuit
terminals, and connect the cable insulation to the corresponding common terminal. (Tightening torque:
0.7Nm,max torque: 0.8Nm)
3) The length of cables connected to control circuit terminals must be 20 m or less. If the cable length exceeds
20 m unavoidably, you should use UP/DOWN function or current signal input with an isolation amplifier.
4) Separate the control circuit wiring from the main circuit wiring (power line) and relay control circuit wiring.
If these wirings intersect with each other unavoidably, square them with each other. Otherwise, the inverter
may malfunction.
5) Twist the cables connected from a thermistor to the thermistor input terminal (TH) and terminal CM1, and
separate the twisted cables from other cables connected to other common terminals. Since very low current
flows through the cables connected to the thermistor, separate the cables from those (power line cables)
connected to the main circuit. The length of the cables connected to the thermistor must be 20 m or less.
6) When connecting a contact to a control circuit terminal (e.g., an intelligent input terminal), use a relay contact
(e.g., crossbar twin contact) in which even a very low current or voltage will not trigger any contact fault.
7) When connecting a relay to an intelligent output terminal, also connect a surge-absorbing diode in parallel
with the relay.
8) Do not connect analog power supply terminals H and L or interface power supply terminals P24 and CM1 to
each other. Otherwise, the inverter may fail.
(2) Layout of control circuit terminals
Terminal screw size: M3 (Tightening torque:0.7Nm,max torque:0.8Nm)
(3) Switching the input control logic
- In the factory setting, the input control logic for terminal FW and intelligent input terminals is the sink logic.
To switch the input control logic to the source logic, remove the jumper connecting terminals P24 and PLC on
the control circuit block, and then connect terminals PLC and CM1 with the jumper.
2 - 19
Chapter 2 Installation and Wiring
When using the internal interface power supply
When using an external power supply
(Remove the jumper from the control circuit terminal block.)
Sink logic
Source logic
Sink logic
Source logic
Inverter
Output module
(EH-YT**,etc.)
Jumper
S
COM
P24
PLC
CM1
FW
8
Inverter
P24
DC24V
CM1
FW
DC24V
S
COM
Output module
(EH-YTP**,etc.)
8
Inverter
Output module
(EH-YTP**,etc.)
DC24V
DC24V
COM
P24
PLC
CM1
FW 8 DC24V
Inverter
Output module
(EH-YT**,etc.)
S
COM
P24
PLC
CM1
FW
8
Jumper
11
12
CM2
COM
Inverter
Input module
(EH-XD**,etc.)
DC24V
Inverter
11
Input module
(EH-XD**,etc.)
12
CM2
COM
DC24V
DC24V
PLC
(4) Connecting a programmable controller to intelligent input terminals
(5) Connecting a programmable controller to intelligent output terminals
2.2.4 Wiring of the digital operator
- You can operate the inverter with not only the digital operator mounted in the inverter as standard equipment but
also an optional digital operator (OPE-S, OPE-SR, WOP).
- When you intend to remove the standard digital operator from the inverter and use it as remote equipment, request
your local Hitachi Distributor to supply a connection cable, ICS-1 (1-meter cable) or ICS-3 (3-meter cable). If you
prepare the cable by yourself, the following product is recommended: HUTP5 PC 4P -X-X: Straight cable
equipped with connector at both ends (made by Hitachi Metal, Ltd.)
- The length of the connection cable must be 3 m or less. If a cable over 3 m is used, the inverter may malfunction.
2 - 20
Chapter 3 Operation
This chapter describes typical methods of operating the inverter, how to operate the digital
operator, and how to make a test run of the inverter.
3.1 Operating Methods ······································ 3 - 2
3.2 How To Operate the Digital Operator (OPE-SBK) ···· 3 - 4
Chapter 3 Operation
WARNING
- While power is supplied to the inverter, do not touch any terminal or internal part of the inverter, check signals,
or connect or disconnect any wire or connector. Otherwise, you run the risk of electric shock or fire.
- Be sure to close the terminal block cover before turning on the inverter power. Do not open the terminal block
cover while power is being supplied to the inverter or voltage remains inside. Otherwise, you run the risk of
electric shock.
- Do not operate switches with wet hands. Otherwise, you run the risk of electric shock.
- While power is supplied to the inverter, do not touch the terminal of the inverter, even if it has stopped.
Otherwise, you run the risk of injury or fire.
- If the retry mode has been selected, the inverter will restart suddenly after a break in the tripping status. Stay
away from the machine controlled by the inverter when the inverter is under such circumstances. (Design the
machine so that human safety can be ensured, even when the inverter restarts suddenly.) Otherwise, you run the
risk of injury.
- Do not select the retry mode for controlling an elevating or traveling device because output free-running status
occurs in retry mode. Otherwise, you run the risk of injury or damage to the machine controlled by the inverter.
- If an operation command has been input to the inverter before a short-term power failure, the inverter may
restart operation after the power recovery. If such a restart may put persons in danger, design a control circuit
that disables the inverter from restarting after power recovery. Otherwise, you run the risk of injury.
- The [STOP] key is effective only when its function is enabled by setting. Prepare an emergency stop switch
separately. Otherwise, you run the risk of injury.
- If an operation command has been input to the inverter before the inverter enters alarm status, the inverter will
restart suddenly when the alarm status is reset. Before resetting the alarm status, make sure that no operation
command has been input.
- While power is supplied to the inverter, do not touch any internal part of the inverter or insert a bar in it.
Otherwise, you run the risk of electric shock or fire.
CAUTION
- Do not touch the heat sink, which heats up during the inverter operation. Otherwise, you run the risk of burn
injury.
- The inverter allows you to easily control the speed of motor or machine operations. Before operating the
inverter, confirm the capacity and ratings of the motor or machine controlled by the inverter. Otherwise, you run
the risk of injury and damage to machine.
- Install an external brake system if needed. Otherwise, you run the risk of injury.
- When using the inverter to operate a standard motor at a frequency of over 60 Hz, check the allowable motor
speeds with the manufacturers of the motor and the machine to be driven and obtain their consent before starting
inverter operation. Otherwise, you run the risk of damage to the motor and machine and injury
- During inverter operation, check the motor for the direction of rotation, abnormal sound, and vibrations.
Otherwise, you run the risk of damage to the machine driven by the motor.
3.1 Operating Methods
3 - 2
Chapter 3 Operation
Digital operator
Operation command input device
(switch)
Frequency-setting command input
device (control)
Control circuit
terminal block
H O L
FW
You can operate the inverter in different ways, depending on how to input the operation and frequency-setting
commands as described below.
This section describes the features of operating methods and the items required for operation.
(1) Entering operation and frequency-setting commands from the digital operator
This operating method allows you to operate the inverter through key operations on the standard digital operator
mounted in the inverter or an optional digital operator.
When operating the inverter with a digital operator alone, you need not wire the control circuit terminals.
(Items required for operation)
*) Optional digital operator (not required when you use the standard digital operator)
(2) Entering operation and frequency-setting commands via control circuit terminals
This operating method allows you to operate the inverter via the input of operation signals from external devices
(e.g., frequency-setting circuit and start switch) to control circuit terminals. The inverter starts operation when
the input power supply is turned on and then an operation command signal (FW or RV) is turned on. You can
select the frequency-setting method (setting by voltage specification or current specification) through the input to
a control circuit terminal according to your system. For details, see Item (2), "Explanation of control circuit
terminals," in Section 2.2.1. (Items required for operation)
1) Operation command input device: External switch or relay
2) Frequency-setting command input device: External device to input signals (0 to 10 VDC, -10 to +10 VDC, or 4
to 20 mA)
(3) Entering operation and frequency-setting commands; both from a digital operator and via control circuit
terminals
This operating method allows you to arbitrarily select the digital operator or control circuit terminals as the
means to input operation commands and frequency-setting commands. (Items required for operation)
1) See the items required for the above two operating methods.
(4) Operation by Easy sequence function (Drive programming function)
The inverter can be operated by downloading the user's program made with the dedicated PC software,
ProDriveNext. Please refer to “Easy sequence function” for details.
(5) Operation via communication
The inverter can be operated by an external communication device via Modbus-RTU or ASCII protocol (Hitachi
protocol) through the TM2 terminal on the control terminal l board. Please refer to “Communication function”
for details.
3 - 3
Chapter 3 Operation
Name
Function
POWER lamp
Lights when the control circuit power is on.
ALARM lamp
Lights to indicate that the inverter has tripped.
RUN (operation) lamp
Lights to indicate that the inverter is operating.
PRG (program) lamp
Lights when the monitor shows a value set for a function.
This lamp starts blinking to indicate a warning (when the set value is invalid).
Monitor
Displays a frequency, output current, or set value.
Monitor lamps
Indicates the type of value and units displayed on the monitor. "Hz" (frequency), "V"
(voltage), "A" (current), "kW" (electric power), and "%" (percentage)
RUN key enable LED
Lights up when the inverter is ready to respond to the RUN key. (When this lamp is on,
you can start the inverter with the RUN key on the digital operator.)
RUN key
Starts the inverter to run the motor. This key is effective only when the RUN command
source setting A002 is set to “02”: digital operator. (To use this key, confirm that RUN
key enable LED is on.)
STOP/RESET key
Decelerates and stops the motor or resets the inverter from alarm status.
FUNC (function) key
Makes the inverter enter the monitor, function, or extended function mode.
STR (storage) key
Stores each set value. (Always press this key after changing a set value.)
1 (up) or 2 (down) key
Switches the inverter operation mode (among monitor, function, and extended function
modes) or increases or decreases the value set on the monitor for a function.
Monitor lamps
2 (down) key
ALARM lamp
POWER lamp
STR (storage) key
PRG (program) lamp
RUN key enable LED
1 (up) key
RUN (operation) lamp
Monitor
(4-digit LED display)
RUN key
FUNC (function) key
STOP/RESET key
3.2 How To Operate the Digital Operator (OPE-SBK)
3.2.1 Names and functions of components
3 - 4
Chapter 3 Operation
The initial display on the monitor screen after power-on depends on the setting of function "b038". For details, see
"Initial-screen selection,”
When the setting of function "b038" is "01" (factory setting), the monitor initially shows as the
setting of function "d001" (output frequency monitoring). Pressing the key in this status changes the
display to .
FUNC
FUNC
FUNC
FUNC
3.2.2 Code display system and key operations
This section describes typical examples of digital operator operation (full display mode). Refer to SJ700D-3
Instruction manual for more information.
Note: The display contents on the monitor depend on the settings of functions "b037" (function code display
restriction), "b038" (initial-screen selection), and "b039" (automatic setting of user parameters). Refer to
SJ700D-3 Instruction manual for more information.
- The following procedure enables you to turn the monitor display back to or *
regardless of the current display mode:
- Hold down the key for 3 seconds or more. The monitor shows * .
- During this status, press the key. The monitor will show only or *,
which is shown when the is pressed.
*) The monitor shows only when the motor driven by the inverter is stopped. While the motor is
running, the monitor shows an output frequency. The displayed monitor is depending on "b038" (initial-screen
selection).
3 - 5
Chapter 3 Operation
Key operation and transition
of codes on display (in
monitor or function mode)
Key operation and transition
of monitored data on display
(in monitor or function
mode)
Key operation and transition
of codes on display (in
extended function mode)
Key operation and transition
of monitored data on display
(in extended function mode)
1
2
1
2
*1 The content of the display varies depending on the parameter type.
*2 To update numerical data, be sure to press the key after
changing the data.
FUNC
Monitor
mode
(Monitor
display)
(*1)
(Data display)
(*1) (*2)
Function
mode
or
FUNC
STR
FUNC
FUNC
FUNC
FUNC
FUNC
or
FUNC
STR
or
FUNC
STR
or
FUNC
STR
or
FUNC
STR
or
FUNC
STR
or
FUNC
STR
or
FUNC
STR
FUNC
Extended
function
mode A
Refer to the
SJ700D-3
Instruction Manual.
(*1) (*2)
(Data display)
Extended
function
mode B
Extended
function
mode C
Extended
function
mode H
Extended
function
mode P
or
FUNC
STR
FUNC
STR
FUNC
Example of operation in full display mode ("b037" = "00") [Factory setting]
All parameters can be displayed in full display mode. If you use other display mode, refer to the SJ700D-3
Instruction Manual.
Pressing the or key respectively scrolls up or down the code displayed in code display mode or increases
or decreases the numerical data displayed in data display mode.
Press the or key until the desired code or numerical data is shown. To scroll codes or increase/decrease
numerical data fast, press and hold the key.
3 - 6
Chapter 3 Operation
FUNC
STR
RUN
STOP/
RESET
FUNC
STR
RUN
STOP/
RESET
FUNC
RUN
STOP/
RESET
FUNC
STR
RUN
STOP/
RESET
STR
FUNC
RUN
STOP/
RESET
STR
FUNC
STR
RUN
STOP/
RESET
FUNC
RUN
STOP/
RESET
STR
FUNC
STR
RUN
STOP/
RESET
FUNC
STR
RUN
STOP/
RESET
FUNC
STR
FUNC
FUNC
STR
FUNC
(*2)
(*3)
2) Change to the extended function mode.
Press the and keys
together. (*1)
1
- Character "d" in the leftmost digit (fourth digit
from the right) starts blinking.
2
Press the key twice.
1
("A001" is displayed.)
(*3)
- Character "A" is blinking.
- Pressing the [STR] key determines the blinking
character.
(*2)
Press the key
(to determine character "A").
3) Change the third digit of the code.
- Character "0" in the third digit is blinking.
- Since the third digit need not be changed,
press the [STR] key to determine the character
"0".
- Character "0" in the second digit is
blinking.
Press the
key.
(Character "0" is
determined.)
(*2)
4) Change the second digit of the code.
Press the key twice.
1
- Character "2" in the second digit is
blinking.
(*2)
(*2)
- Character "1" in the first digit is blinking.
STR
Press the key.
("A021" is displayed.)
5) Change the first digit of the code.
- Character "9" in the first digit is blinking.
Press the key eight times or
the key twice.
1
2
(*2)
STR
Press the
key.
(Character "9"
is determined.)
- Selection of code "A029" is completed.
* If a code that is not defined in the code list or
not intended for display is entered, the
leftmost digit (fourth digit) (character "A" in
this example) will start blinking again.
In such a case, confirm the code to be entered
and enter it correctly. For further information,
refer to Section 4.2.84. " Function code
display restriction," (on page 4-79), Section
4.2.85, "Initial-screen selection," (on page
4-81), Section 4.2.86, "Automatic
user-parameter setting," (on page 4-82), and
Chapter 8, "List of Data Settings."
7) Press the key to display the data
corresponding to the function code, change
the data with the and/or
key, and then press the key to
store the changed data. (*4)
Note that you can also use the procedure
(steps 1) to 6)) described here to change the
data. (*3)(*4)
*1
This procedure can also be used on screens
displaying a code other than "d001".
*2
If the key is pressed while a digit is
blinking, the display will revert to the
preceding status for entering the digit to the
right of the blinking digit.
*3
If the key is pressed while the leftmost
(fourth) digit is blinking, the characters
having been entered to change the code will
be cancelled and the display will revert to the
original code shown before the and
keys were pressed in step 1).
*4
When changing data, be sure to press the
key first.
FUNC
1
2
FUNC
FUNC
FUNC
1
2
STR
("d001" is displayed.)
1) Display the monitor mode code.
6) End the change of the extended function code.
Procedure for directly specifying or selecting a code
- You can specify or select a code or data by entering each digit of the code or data instead of scrolling codes or
data in the monitor, function, or extended function mode.
- The following shows an example of the procedure for changing the monitor mode code "d001" displayed to
extended function code "A029":
("A029" is displayed.)
3 - 7
Chapter 3 Operation
(Memo)
3 - 8
Chapter 4 List of Data Settings
This chapter describes the data settings for the various functions of the inverter.
4.1 Precautions for Data Setting ....................... 4 - 2
4.2 Monitoring Mode ....................................... 4 - 2
4.3 Function Mode ......................................... 4 - 3
4.4 Extended Function Mode ......................... 4 - 4
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
d001
Output frequency monitoring
0.00 to 99.99, 100.0 to 400.0 (Hz)
Allowed
Allowed
d002
Output current monitoring
0.0 to 999.9, 1000 to 9999 (A)
d003
Rotation direction monitoring
(forward rotation), (stopped), (reverse rotation)
d004
Process variable (PV),
PID feedback monitoring
0.00 to 99.99, 100.0 to 999.9, 1000. to 9999.
1000 to 9999 (10000 to 99990), 100 to 999 (100000 to 999000)
d005
Intelligent input
terminal status
(Example)
Terminals FW, 7, 2, and 1: ON
Terminals 8, 6, 5, 4, and 3: OFF
d006
Intelligent output
terminal status
(Example)
Terminals 12 and 11: ON
Terminals AL, 15, 14, and 13: OFF
d007
Scaled output frequency
monitoring
0.00 to 99.99, 100.0 to 999.9, 1000. to 9999,
1000 to 3996 (10000 to 39960)
Allowed
Allowed
d008
Actual-frequency monitoring
-400. to -100., -99.9 to 0.00 to 99.99, 100.0 to 400.0 (Hz)
d009
Torque command monitoring
-200. to +200. (%)
d010
Torque bias monitoring
d012
Torque monitoring
d013
Output voltage monitoring
0.0 to 600.0 (V)
d014
Power monitoring
0.0 to 999.9 (kW)
d015
Cumulative power monitoring
0.0 to 999.9, 1000. to 9999.1000 to 9999 (10000 to 99990),
100 to 999 (100000 to 999000)
d016
Cumulative operation RUN time
monitoring
0. to 9999., 1000 to 9999 (10000 to 99990),
100 to 999 (100000 to 999000) (hr)
d017
Cumulative power-on time
monitoring
d018
Heat sink temperature monitoring
-020. to 200.0 (C)
d019
Motor temperature monitoring
FW
8 7 6 5 4 3 2
1
AL
15
14
13
12
11
IMPORTANT! Please be sure to set the motor nameplate data into appropriate parameters to ensure proper
operation and protection of the motor.
*b012 is the motor overload protection value
*A003 is the motor base frequency setting *A082 is the motor voltage selection
*H003 is the motor kW capacity *H004 is the number of motor poles
Please refer to the appropriate pages in this guide and the Instruction Manual for further details.
4.1 Precautions for Data Setting
- FF, FEF and FUF are the parts of inverter model.
For example, in case of 1.5kW/400V class, SJ700D-015H***3 (*** is described as FF, FEF or FUF.)
- Even though the inverter is driving the motor, you can change some parameters. If you specify "10" for the
software lock mode selection (b031), you can change some more parameters. See the table below.
- In case of setting VT mode, some parameters and some data become invisible. Refer to the SJ700D-3 instruction
manual for more information.
4.2 Monitoring Mode
With the default settings, the initial display on the operator after powering on is always the output frequency monitor
(d001). To change the initial display content, change the setting of the initial-screen selection (b038) as required.
4 - 2
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
F001
Output frequency setting
0.0, "start frequency" to "maximum frequency"
(or maximum frequency, 2nd/3rd motors) (Hz)
0.0 to 100.0 (when PID function is enabled)
0.00
Allowed
Allowed
F002
Acceleration time setting
0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)
30.00
Allowed
Allowed
F202
Acceleration time setting,
2nd motor
30.00
Allowed
Allowed
F302
Acceleration time setting,
3rd motor
30.00
Allowed
Allowed
F003
Deceleration time setting
0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)
30.00
Allowed
Allowed
F203
Deceleration time setting,
2nd motor
30.00
Allowed
Allowed
F303
Deceleration time setting,
3rd motor
30.00
Allowed
Allowed
F004
Keypad Run key routing
00 (forward rotation), 01 (reverse rotation)
00
Not
Not
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
d022
Life-check monitoring
1: Capacitor on main circuit board
2: Cooling-fan speed drop
d023
Program counter
0 to 1024 d024
Program number monitoring
0000 to 9999
d025
User monitor 0
-2147483647 to 2147483647 (upper 4 digits including “-“)
d026
User monitor 1
d027
User monitor 2
d028
Pulse counter
0 to 2147483647 (upper 4 digits)
d029
Position setting monitor
-1073741823 to 1073741823 (upper 4 digits including “-“)
d030
Position feedback monitor
d031
Clock monitor
* In case you use WOP (option), this monitor is activated.
d060
Inverter mode monitor
I-C(CT)/ I-v(VT)
d080
Trip Counter
0. to 9999., 1000 to 6553 (10000 to 65530) (times)
d081
Trip monitoring 1
Factor,
frequency (Hz),
current (A),
voltage across P-N (V),
running time (hours),
power-on time (hours)
d082
Trip monitoring 2
d083
Trip monitoring 3
d084
Trip monitoring 4
d085
Trip monitoring 5
d086
Trip monitoring 6
d090
Programming error monitoring
Warning code
d102
DC voltage monitoring
0.0 to 999.9 (V)
d103
BRD load factor monitoring
0.0 to 100.0 (%)
d104
Electronic thermal overload
monitoring
2 1 ON
OFF
(Note) CT : Constant torque mode, VT : Variable torque mode, you can set CT or VT by b049.
4.3 Function Mode
4 - 3
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
Basic settings
A001
Frequency source setting
00 (keypad potentiometer) (*1), 01 (control circuit terminal block),
02 (digital operator), 03 (RS485), 04 (option 1), 05 (option 2),
06 (pulse-string input), 07 (easy sequence),
10 (operation function result)
02
01
01
Not
Not
A002
Run command source setting
01 (control circuit terminal block), 02 (digital operator), 03 (RS485),
04 (option 1), 05 (option 2)
02
01
01
Not
Not
A003
Base frequency setting
30. to "Maximum frequency " (Hz)
60.
50.
60.
Not
Not
A203
Base frequency setting, 2nd motor
30. to "Maximum frequency, 2nd motor" (Hz)
60.
50.
60.
Not
Not
A303
Base frequency setting, 3rd motor
30. to "Maximum frequency, 3rd motor" (Hz)
60.
50.
60.
Not
Not
A004
Maximum frequency setting
"Base frequency” (Hz) to 400. (Hz)
60.
50.
60.
Not
Not
A204
Maximum frequency setting, 2nd motor
"Base frequency, 2nd motor” (Hz) to 400. (Hz)
60.
50.
60.
Not
Not
A304
Maximum frequency setting, 3rd motor
"Base frequency, 3rd motor” (Hz) to 400. (Hz)
60.
50.
60.
Not
Not
Analog input and others
A005
[AT] selection
00 (switching between O and OI terminals),
01 (switching between O and O2 terminals),
02 (switching between O terminal and keypad potentiometer) (*1),
03 (switching between OI terminal and keypad potentiometer) (*1),
04 (switching between O2 and keypad potentiometer) (*1)
00
Not
Not
A006
[O2] selection
00 (single),
01 (auxiliary frequency input via O and OI terminals) nonreversible),
02 (auxiliary frequency input via O and OI terminals) (reversible),
03 (disabling O2 terminal)
03
Not
Not
A011
[O]-[L] input active range start frequency
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
A012
[O]-[L] input active range end frequency
0.00 to 99.99, 100.0 to 400.0 (Hz)
(In case of setting 0.00, internal setting is "Maximum frequency ")
0.00
Not
Allowed
A013
[O]-[L] input active range start voltage
0. to "[O]-[L] input active range end voltage" (%)
0.
Not
Allowed
A014
[O]-[L] input active range end voltage
"[O]-[L] input active range start voltage" to 100. (%)
100.
Not
Allowed
A015
[O]-[L] input active range start frequency
selection
00 (external start frequency), 01 (0 Hz)
01
Not
Allowed
A016
External frequency filter time const.
1. to 30. or 31. (500 ms filter ±0.1 Hz with hysteresis)
31.
Not
Allowed
A017
Easy sequence function selection
00 (disabling), 01 (enabling)
00
Not
Not
Multispeed operation and jogging
A019
Multispeed operation selection
00 (binary: 16 speeds selectable with 4 terminals),
01 (bit: 8 speeds selectable with 7 terminals)
00
Not
Not
A020
Multispeed frequency setting
0.0 or “start frequency” to “maximum frequency” (Hz)
0.00
Allowed
Allowed
A220
Multispeed frequency setting, 2nd motor
0.0 or “start frequency” to “maximum frequency, 2nd motor” (Hz)
0.00
Allowed
Allowed
A320
Multispeed frequency setting, 3rd motor
0.0 or “start frequency” to “maximum frequency, 3rd motor” (Hz)
0.00
Allowed
Allowed
A021
Multispeed 1 setting
0.0 or “start frequency” to “1st maximum frequency” (Hz)
0.00
Allowed
Allowed
A022
Multispeed 2 setting
0.0 or “start frequency” to “2nd maximum frequency” (Hz)
0.00
Allowed
Allowed
A023
Multispeed 3 setting
0.0 or “start frequency” to “3rd maximum frequency” (Hz)
0.00
Allowed
Allowed
A024
Multispeed 4 setting
0.0 or “start frequency” to “n-th maximum frequency” (Hz) (n=1 to 3)
0.00
Allowed
Allowed
A025
Multispeed 5 setting
0.0 or “start frequency” to “n-th maximum frequency” (Hz) (n=1 to 3)
0.00
Allowed
Allowed
A026
Multispeed 6 setting
0.0 or “start frequency” to “n-th maximum frequency” (Hz) (n=1 to 3)
0.00
Allowed
Allowed
A027
Multispeed 7 setting
0.0 or “start frequency” to “n-th maximum frequency” (Hz) (n=1 to 3)
0.00
Allowed
Allowed
A028
Multispeed 8 setting
0.0 or “start frequency” to “n-th maximum frequency” (Hz) (n=1 to 3)
0.00
Allowed
Allowed
A029
Multispeed 9 setting
0.0 or “start frequency” to “n-th maximum frequency” (Hz) (n=1 to 3)
0.00
Allowed
Allowed
A030
Multispeed 10 setting
0.0 or “start frequency” to “n-th maximum frequency” (Hz) (n=1 to 3)
0.00
Allowed
Allowed
A031
Multispeed 11 setting
0.0 or “start frequency” to “n-th maximum frequency” (Hz) (n=1 to 3)
0.00
Allowed
Allowed
A032
Multispeed 12 setting
0.0 or “start frequency” to “n-th maximum frequency” (Hz) (n=1 to 3)
0.00
Allowed
Allowed
A033
Multispeed 13 setting
0.0 or “start frequency” to “n-th maximum frequency” (Hz) (n=1 to 3)
0.00
Allowed
Allowed
A034
Multispeed 14 setting
0.0 or “start frequency” to “n-th maximum frequency” (Hz) (n=1 to 3)
0.00
Allowed
Allowed
A035
Multispeed 15 setting
0.0 or “start frequency” to “n-th maximum frequency” (Hz) (n=1 to 3)
0.00
Allowed
Allowed
A038
Jog frequency setting
"Start frequency" to 9.99 (Hz)
1.00
Allowed
Allowed
A039
Jog stop mode
00 (free-running after jogging stops [disabled during operation]),
01 (deceleration and stop after jogging stops [disabled during operation]),
02 (DC braking after jogging stops [disabled during operation]),
03 (free-running after jogging stops [enabled during operation]),
04 (deceleration and stop after jogging stops [enabled during operation]),
05 (DC braking after jogging stops [enabled during operation])
00
Not
Allowed
4.4 Extended Function Mode
*1 This setting is valid only when the OPE-SR is connected.
4 - 4
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
V/f characteristic
A041
Torque boost method selection
00 (manual torque boost),
01 (automatic torque boost)
00
Not
Not
A241
Torque boost method selection, 2nd motor
00
Not
Not
A042
Manual torque boost value
0.0 to 20.0 (%)
1.0
Allowed
Allowed
A242
Manual torque boost value, 2nd motor
1.0
Allowed
Allowed
A342
Manual torque boost value, 3rd motor
1.0
Allowed
Allowed
A043
Manual torque boost frequency adjustment
0.0 to 50.0 (%)
5.0
Allowed
Allowed
A243
Manual torque boost frequency adjustment,
2nd motor
5.0
Allowed
Allowed
A343
Manual torque boost frequency adjustment,
3rd motor
5.0
Allowed
Allowed
A044
V/F characteristic curve selection,
1st motor
00 (VC), 01 (VP), 02 (free V/f), 03 (sensorless vector control),
04 (0Hz sensorless vector control)(only CT),
05(vector with sensor)(only CT)
00
Not
Not
A244
V/F characteristic curve selection,
2nd motor
00 (VC), 01 (VP), 02 (free V/f), 03 (sensorless vector control),
04 (0Hz sensorless vector control)(only CT)
00
Not
Not
A344
V/F characteristic curve selection,
3rd motor
00(VC), 01(VP)
00
Not
Not
A045
V/f gain setting
20. to 100. (%)
100.
Allowed
Allowed
A046
Voltage compensation gain setting for
automatic torque boost. 1st motor
0. to 255.
100.
Allowed
Allowed
A246
Voltage compensation gain setting for
automatic torque boost, 2nd motor
100.
Allowed
Allowed
A047
Slippage compensation gain setting for
automatic torque boost, 1st motor
0. to 255.
100.
Allowed
Allowed
A247
Slippage compensation gain setting for
automatic torque boost, 2nd motor
100.
Allowed
Allowed
DC braking
A051
DC braking enable
00 (disabling), 01 (enabling), 02 (set frequency only)
00
Not
Allowed
A052
DC braking frequency setting
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.50
Not
Allowed
A053
DC braking wait time
0.0 to 5.0 (s)
0.0
Not
Allowed
A054
DC braking force during deceleration
0. to 100. (%) <0. to 80. (%)> (In case of CT)
0. to 70. (%) <0. to 50. (%)> (In case of VT)
20.
Not
Allowed
A055
DC braking time for deceleration
0.0 to 60.0 (s)
0.5
Not
Allowed
A056
DC braking/edge or level detection
for [DB] input
00 (edge operation), 01 (level operation)
01
Not
Allowed
A057
DC braking force for starting
0. to 100. (%) <0. to 80. (%)> (In case of CT)
0. to 70. (%) <0. to 50. (%)> (In case of VT)
0.
Not
Allowed
A058
DC braking time for starting
0.0 to 60.0(s)
0.0
Not
Allowed
A059
DC braking carrier frequency setting
0.5 to 15.0(kHz) <0.5 to 10.0 (kHz) > (In case of CT)
0.5 to 12.0(kHz) <0.5 to 8.0 (kHz) > (In case of VT)
5.0<3.0> (CT)
3.0 (VT)
Not
Not
Frequency upper/lower limit and jump frequency
A061
Frequency upper limit setting
0.00 or "1st minimum frequency limit" to
"maximum frequency" (Hz)
0.00
Not
Allowed
A261
Frequency upper limit setting, 2nd motor
0.00 or "2nd minimum frequency limit" to
"maximum frequency, 2nd motor" (Hz)
0.00
Not
Allowed
A062
Frequency lower limit setting
0.00 or "start frequency" to "maximum frequency limit" (Hz)
0.00
Not
Allowed
A262
Frequency lower limit setting, 2nd motor
0.00 or "start frequency" to "maximum frequency,
2nd motor limit" (Hz)
0.00
Not
Allowed
A063
Jump (center) frequency setting 1
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
A064
Jump (hysteresis) frequency width setting 1
0.00 to 10.00 (Hz)
0.50
Not
Allowed
A065
Jump (center) frequency setting 2
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
A066
Jump (hysteresis) frequency width setting 2
0.00 to 10.00 (Hz)
0.50
Not
Allowed
A067
Jump (center) frequency setting 3
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
A068
Jump (hysteresis) frequency width setting 3
0.00 to 10.00 (Hz)
0.50
Not
Allowed
A069
Acceleration stop frequency setting
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
A070
Acceleration stop time frequency setting
0.0 to 60.0 (s)
0.0
Not
Allowed
PID control
A071
PID Function Enable
00 (disabling), 01 (enabling), 02 (enabling inverted-data output)
00
Not
Allowed
A072
PID proportional gain
0.2 to 5.0
1.0
Allowed
Allowed
A073
PID integral time constant
0.0 to 999.9, 1000. to 3600. (s)
1.0
Allowed
Allowed
A074
PID derivative gain
0.00 to 99.99, 100.0 (s)
0.00
Allowed
Allowed
A075
PV scale conversion
0.01 to 99.99
1.00
Not
Allowed
A076
PV source setting
00 (input via OI), 01 (input via O), 02 (external communication),
03 (pulse-string frequency input), 10 (operation result output)
00
Not
Allowed
A077
Output of inverted PID deviation
00(OFF), 01 (ON)
00
Not
Allowed
A078
PID variation range
0.0 to 100.0 (%)
0.00
Not
Allowed
A079
PID feed forward selection
00 (disabled), 01 (O input), 02 (OI input), 03 (O2 input)
00
Not
Allowed
(Note) < > indicate the setting range of 75 to 150kW
(Note) CT : Constant torque mode, VT : Variable torque mode, you can set CT or VT by b049.
4 - 5
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
AVR
A081
AVR function select
00 (always on), 01 (always off), 02 (off during deceleration)
02
00
00
Not
Not
A082
AVR voltage select
200 V class: 200, 215, 220, 230, 240 (V)
400 V class: 380, 400, 415, 440, 460, 480 (V)
200/
400
230/
400
230/
460
Not
Not
Operation mode and acceleration/deceleration function
A085
Operation mode selection
00 (normal operation), 01 (energy-saving operation)
02 (fuzzy operation)(only CT)
00
Not
Not
A086
Energy saving mode tuning
0.0 to 100.0
50.0
Allowed
Allowed
A092
Acceleration (2) time setting
0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)
15.00
Allowed
Allowed
A292
Acceleration (2) time setting, 2nd motor
15.00
Allowed
Allowed
A392
Acceleration (2) time setting, 3rd motor
15.00
Allowed
Allowed
A093
Deceleration (2) time setting
0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)
15.00
Allowed
Allowed
A293
Deceleration (2) time setting, 2nd motor
15.00
Allowed
Allowed
A393
Deceleration (2) time setting, 3rd motor
15.00
Allowed
Allowed
A094
Select method to switch to Acc2/Dec2
profile
00 (switching by 2CH terminal), 01 (switching by setting),
02 (switching only when rotation is reversed)
00
Not
Not
A294
Select method to switch to Acc2/Dec2,
2nd motor
00
Not
Not
A095
Acc1 to Acc2 frequency transition point
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Not
A295
Acc1 to Acc2 frequency transition point,
2nd motor
0.00
Not
Not
A096
Dec1 to Dec2 frequency transition point
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Not
A296
Dec1 to Dec2 frequency transition point,
2nd motor
0.00
Not
Not
A097
Acceleration curve selection
00 (linear), 01 (S curve), 02 (U curve),
03 (inverted-U curve), 04 (EL-S curve)
00
Not
Not
A098
Deceleration curve setting
00
Not
Not
External frequency adjustment
A101
[OI]-[L] input active range start frequency
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
A102
[OI]-[L] input active range end frequency
0.00 to 99.99, 100.0 to 400.0 (Hz)
(In case of setting 0.00, internal setting is "Maximum
frequency ")
0.00
Not
Allowed
A103
[OI]-[L] input active range start current
0. to "[OI]-[L] input active range end current" (%)
20.
Not
Allowed
A104
[OI]-[L] input active range end current
"[OI]-[L] input active range start current" to 100. (%)
100.
Not
Allowed
A105
[OI]-[L] input start frequency enable
00 (external start frequency), 01 (0 Hz)
00
Not
Allowed
A111
[O2]-[L] input active range start
frequency
-400. to -100., -99.9 to 0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
A112
[O2]-[L] input active range end frequency
-400. to -100., -99.9 to 0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
A113
[O2]-[L] input active range start voltage
-100. to 02 end-frequency rate (%)
-100.
Not
Allowed
A114
[O2]-[L] input active range end voltage
"02 start-frequency rate" to 100. (%)
100.
Not
Allowed
Acceleration and
deceleration
A131
Acceleration curve constants setting
01 (smallest swelling) to 10 (largest swelling)
02
Not
Allowed
A132
Deceleration curve constants setting
01 (smallest swelling) to 10 (largest swelling)
02
Not
Allowed
Operation-target
frequency
A141
Operation-target frequency selection 1
00 (digital operator), 01 (keypad potentiometer),
02 (input via O), 03 (input via OI),
04 (external communication), 05 (option 1), 06 (option 2),
07 (pulse-string frequency input)
02
Not
Allowed
A142
Operation-target frequency selection 2
03
Not
Allowed
A143
Operator selection
00 (addition: A141 + A142), 01 (subtraction: A141 - A142),
02 (multiplication: A141 x A142)
00
Not
Allowed
A145
Frequency to be added
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
A146
Sign of the frequency to be added
00 (frequency command + A145),
01 (frequency command - A145)
00
Not
Allowed
Acceleration and
deceleration
A150
EL-S-curve acceleration
ratio 1
0. to 50. (%)
25.
Not
Not
A151
EL-S-curve acceleration
ratio 2
25.
Not
Not
A152
EL-S-curve deceleration
ratio 1
0. to 50. (%)
25.
Not
Not
A153
EL-S-curve deceleration
ratio 2
25.
Not
Not
*1 This setting is valid only when the OPE-SR is connected.
(Note) CT : Constant torque mode, VT : Variable torque mode, you can set CT or VT by b049.
4 - 6
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
Restart after instantaneous power failure or tripping
b001
Selection of restart mode
00 (tripping), 01 (starting with 0 Hz),
02 (starting with matching frequency),
03 (tripping after deceleration and stopping with matching
frequency), 04 (restarting with active matching frequency)
00
Not
Allowed
b002
Allowable under-voltage power failure time
0.3 to 25.0 (s)
1.0
Not
Allowed
b003
Retry wait time before motor restart
0.3 to 100.0 (s)
1.0
Not
Allowed
b004
Instantaneous power failure/under-voltage trip
alarm enable
00 (disabling), 01 (enabling),
02 (disabling during stopping and decelerating to stop)
00
Not
Allowed
b005
Number of restarts on power
failure/under-voltage trip events
00 (16 times), 01 (unlimited)
00
Not
Allowed
b006
Input phase loss detection enable
00 (disabling), 01 (enabling)
00
Not
Allowed
b007
Restart frequency threshold
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
b008
Selection of retry after tripping
00 (tripping), 01 (starting with 0 Hz),
02 (starting with matching frequency),
03 (tripping after deceleration and stopping with matching
frequency), 04 (restarting with active matching frequency)
00
Not
Allowed
b009
Selection of retry after under voltage
00 (16 times), 01 (unlimited)
00
Not
Allowed
b010
Selection of retry count after overvoltage or
overcurrent
1 to 3 (times)
3
Not
Allowed
b011
Retry wait time after tripping
0.3 to 100.0 (s)
1.0
Not
Allowed
Electronic thermal function
b012
Electronic thermal setting
0.20 x "rated current" to 1.00 x "rated current" (A)
Rated current
Not
Allowed
b212
Electronic thermal setting , 2nd motor
Rated current
Not
Allowed
b312
Electronic thermal setting, 3rd motor
Rated current
Not
Allowed
b013
Electronic thermal characteristic
00 (reduced-torque characteristic),
01 (constant-torque characteristic),
02 (free setting)
00
01
01
Not
Allowed
b213
Electronic thermal characteristic, 2nd motor
00
01
01
Not
Allowed
b313
Electronic thermal characteristic, 3rd motor
00
01
01
Not
Allowed
b015
Free setting, electronic thermal frequency (1)
0. to 400. (Hz)
0.
Not
Allowed
b016
Free setting, electronic thermal current (1)
0.0 to rated current (A)
0.0
Not
Allowed
b017
Free setting, electronic thermal frequency (2)
0. to 400. (Hz)
0.
Not
Allowed
b018
Free setting, electronic thermal current (2)
0.0 to rated current (A)
0.0
Not
Allowed
b019
Free setting, electronic thermal frequency (3)
0. to 400. (Hz)
0.
Not
Allowed
b020
Free setting, electronic thermal current (3)
0.0 to rated current (A)
0.0
Not
Allowed
Overload restriction and overcurrent restraint
b021
Overload restriction operation mode
00 (disabling), 01 (enabling during acceleration and deceleration),
02 (enabling during constant speed),
03 (enabling during acceleration and deceleration (increasing the
speed during regeneration))
01
Not
Allowed
b022
Overload restriction setting
0.20 x "rated current" to 2.00 x "rated current" (A)
<0.20 x "rated current" to1.80 x "rated current" (A)>
(In case of CT)
0.20 x "rated current" to 1.50 x "rated current" (A)
(In case of VT)
Rated current
x 1.50 (CT)
Rated current
x1.20 (VT)
Not
Allowed
b023
Deceleration rate at overload restriction
0.10 to 30.00 (s)
1.00
Not
Allowed
b024
Overload restriction operation mode (2)
00 (disabling), 01 (enabling during acceleration and deceleration),
02 (enabling during constant speed),
03 (enabling during acceleration and deceleration (increasing the
speed during regeneration))
01
Not
Allowed
b025
Overload restriction setting (2)
0.20 x "rated current" to 1.50 x "rated current" (A)
<0.20 x "rated current" to1.50 x "rated current" (A)>
Rated current
x 1.50 (CT)
Rated current
x1.20 (VT)
Not
Allowed
b026
Deceleration rate at overload restriction (2)
0.10 to 30.00 (s)
1.00
Not
Allowed
b027
Overcurrent suppression enable
00 (disabling), 01 (enabling)
01
Not
Allowed
b028
Active frequency matching, scan start frequency
0.20 x "rated current" to 2.00 x "rated current" (A)
<0.20 x "rated current" to1.80 x "rated current" (A)>
(In case of CT)
0.20 x "rated current" to 1.50 x "rated current" (A)
(In case of VT)
Rated current
Not
Allowed
b029
Active frequency matching, scan-time constant
0.10 to 30.00 (s)
0.50
Not
Allowed
b030
Active frequency matching, restart frequency
select
00 (frequency at the last shutoff),
01 (maximum frequency), 02 (set frequency)
00
Not
Allowed
Software lock
b031
Software lock mode selection
00 (disabling change of data other than "b031" when SFT is on),
01 (disabling change of data other than "b031" and frequency
settings when SFT is on),
02 (disabling change of data other than "b031"),
03 (disabling change of data other than "b031" and frequency
settings),
10 (enabling data changes during operation)
01
Not
Allowed
(Note) < >indicate the setting range of 75 to 150kW
(Note) CT : Constant torque mode, VT : Variable torque mode, you can set CT or VT by b049.
4 - 7
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
Others
b034
Run/power-on warning time
0. to 9999. (0 to 99990),
1000 to 6553 (100000 to 655300) (hr)
0.
Not
Allowed
b035
Rotational direction restriction
00 (enabling both forward and reverse rotations),
01 (enabling only forward rotation),
02 (enabling only reverse rotation)
00
Not
Not
b036
Reduced voltage start selection
0 (minimum reduced voltage start time) to
255 (maximum reduced voltage start time)
6
Not
Allowed
b037
Function code display restriction
00 (full display), 01 (function-specific display),
02 (user setting), 03 (data comparison display), 04 (basic display)
00
Not
Allowed
b038
Initial-screen selection
00 (screen displayed when the STR key was pressed last),
001~060 (d001~d060), 201 (F001) 202 *)
001
Not
Allowed
b039
Automatic user-parameter setting
function enable
00 (disabling), 01 (enabling)
00
Not
Allowed
Torque limitation
b040
Torque limit selection
00 (quadrant-specific setting), 01 (switching by terminal),
02 (analog input), 03 (option 1), 04 (option 2)
00
Not
Allowed
b041
Torque limit (1)
(forward-driving in 4-quadrant mode)
0. to 200. (%), no (disabling torque limitation)
<0. to 150. (%), no (disabling torque limitation)> (In case of CT)
0. to 150. (%), no (disabling torque limitation)(In case of VT)
150.(CT)
120.(VT)
Not
Allowed
b042
Torque limit (2)
(reverse-regenerating in 4-quadrant mode)
150.(CT)
120.(VT)
Not
Allowed
b043
Torque limit (3)
(reverse-driving in 4-quadrant mode)
150.(CT)
120.(VT)
Not
Allowed
b044
Torque limit (4)
(forward-regenerating in 4-quadrant mode)
150.(CT)
120.(VT)
Not
Allowed
b045
Torque limit LADSTOP enable
00 (disabling), 01 (enabling)
00
Not
Allowed
b046
Reverse Run protection enable
00 (disabling), 01 (enabling)
00
Not
Allowed
Mode
b049
Dual rating selection
00 (CT : Constant torque)
01 (VT : Variable torque)
00(CT)
01(VT)
Not
Not
Non-stop operation at momentary
power failure
b050
Controller deceleration and stop on power
loss
00 (disabling), 01 (nonstop deceleration to stop),
02 (DC voltage constant control, with resume),
03 (DC voltage constant control, without resume)
00
Not
Not
b051
DC bus voltage trigger level during power
loss
0.0 to 999.9, 1000. (V)
220.0/440.0
Not
Not
b052
Over-voltage threshold during power loss
0.0 to 999.9, 1000. (V)
360.0/720.0
Not
Not
b053
Deceleration time setting during power loss
0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s)
1.00
Not
Not
b054
Initial output frequency decrease during
power loss
0.00 to 10.00 (Hz)
0.00
Not
Not
b055
Proportional gain setting for nonstop
operation at power loss
0.00 to 2.55
0.20
Allowed
Allowed
b056
Integral time setting for nonstop operation
at power loss
0.000 to 9.999 /10.00 to 65.53 (s)
0.100
Allowed
Allowed
Window comparator
b060
Maximum-limit level of window
comparators O
0. to 100. (lower limit : b061 + b062 x 2) (%)
100
Allowed
Allowed
b061
Minimum-limit level of window
comparators O
0. to 100. (upper limit : b060 - b062 x 2) (%)
0
Allowed
Allowed
b062
Hysteresis width of window comparators O
0. to 10. (upper limit : b060 - b061 / 2) (%)
0
Allowed
Allowed
b063
Maximum-limit level of window
comparators OI
0. to 100. (lower limit : b064 + b065 x 2) (%)
100
Allowed
Allowed
b064
Minimum-limit level of window
comparators OI
0. to 100. (upper limit : b063 - b064 x 2) (%)
0
Allowed
Allowed
b065
Hysteresis width of window comparators
OI
0. to 10. (upper limit : b063 - b064 / 2) (%)
0
Allowed
Allowed
b066
Maximum-limit level of window
comparators OI
-100. to 100. (lower limit : b067 + b068 x 2) (%)
100
Allowed
Allowed
b067
Minimum-limit level of window
comparators O/OI/O2
-100. to 100. (upper limit : b066 - b068 x 2) (%)
-100
Allowed
Allowed
b068
Hysteresis width of window comparators
O/OI/O2
0. to 10. (upper limit : b066 - b067 / 2) (%)
0
Allowed
Allowed
b070
Operation level at O disconnection
0. to 100. (%) or "no" (ignore)
no
Not
Allowed
b071
Operation level at OI disconnection
0. to 100. (%) or "no" (ignore)
no
Not
Allowed
b072
Operation level at O2 disconnection
-100. to 100. (%) or "no" (ignore)
no
Not
Allowed
(Note) < > indicate the setting range of 75 to 150kW
(Note) CT : Constant torque mode, VT : variable torque mode, you can set CT or VT by b049.
*) In case of connecting OPE-S to the inverter, ‘201’ setting is same as ‘00’ setting. Refer to the SJ700D-3 instruction manual.
4 - 8
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
Others
b078
Cumulative input power data clearance
Clearance by setting "01" and pressing the STR key
00
Allowed
Allowed
b079
Cumulative input power display gain
setting
1. to 1000.
1.
Allowed
Allowed
b082
Start frequency adjustment
0.10 to 9.99 (Hz)
0.50
Not
Allowed
b083
Carrier frequency setting
0.5～15.0(kHz) <0.5～10.0(kHz)> (In case of CT)
0.5～12.0(kHz) (In case of VT)
5.0<3.0>(CT)
3.0(VT)
Not
Not
b084
Initialization mode
(parameters or trip history)
00 (disabled), 01 (clearing the trip history), 02 (initializing the data),
03 (clearing the trip history and initializing the data),
04 (clearing the trip history and initializing the data and EzSQ program)
00
Not
Not
b085
Country for initialization
00 (JPN), 01(EU), 02(USA)
00
01
02
Not
Not
b086
Frequency scaling conversion factor
0.1 to 99.0
1.0
Allowed
Allowed
b087
STOP key enable
00 (enabling), 01 (disabling), 02 (disabling only the function to stop)
00
Not
Allowed
b088
Restart mode after FRS
00 (starting with 0 Hz), 01 (starting with matching frequency),
02 (starting with active matching frequency)
00
Not
Allowed
b089
Automatic carrier frequency reduction
00: invalid, 01: valid
00
Not b090
Dynamic braking usage ratio
0.0 to 100.0 (%)
0.0
Not
Allowed
b091
Stop mode selection
00 (deceleration until stop), 01 (free-run stop)
00
Not
Allowed
b092
Cooling fan control
00 (always operating the fan), 01 (operating the fan only during
inverter operation [including 5 minutes after power-on and power-off])
01
Not
Allowed
b095
Dynamic braking control
00 (disabling), 01 (enabling [disabling while the motor is topped]),
02 (enabling [enabling also while the motor is topped])
01
Not
Allowed
b096
Dynamic braking activation level
330 to 390 (V) (200 V class model),
660 to 780 (V) (400 V class model)
360/720
Not
Allowed
b098
Thermistor for thermal protection control
00 (disabling the thermistor), 01 (enabling the thermistor with PTC),
02 (enabling the thermistor with NTC)
00
Not
Allowed
b099
Thermal protection level setting
0. to 9999. ()
3000.
Not
Allowed
Free setting of V/f characteristic
b100
Free-setting V/f frequency (1)
0. to "free-setting V/f frequency (2)" (Hz)
0.
Not
Not
b101
Free-setting V/f voltage (1)
0.0 to 800.0 (V)
0.0
Not
Not
b102
Free-setting V/f frequency (2)
"free-setting V/f frequency (1)" to "free-setting V/f frequency (3)" (Hz)
0.
Not
Not
b103
Free-setting V/f voltage (2)
0.0 to 800.0 (V)
0.0
Not
Not
b104
Free-setting V/f frequency (3)
"free-setting V/f frequency (2)" to "free-setting V/f frequency (4)" (Hz)
0.
Not
Not
b105
Free-setting V/f voltage (3)
0.0 to 800.0 (V)
0.0
Not
Not
b106
Free-setting V/f frequency (4)
"free-setting V/f frequency (3)" to "free-setting V/f frequency (5)" (Hz)
0.
Not
Not
b107
Free-setting V/f voltage (4)
0.0 to 800.0 (V)
0.0
Not
Not
b108
Free-setting V/f frequency (5)
"free-setting V/f frequency (4)" to "free-setting V/f frequency (6)" (Hz)
0.
Not
Not
b109
Free-setting V/f voltage (5)
0.0 to 800.0 (V)
0.0
Not
Not
b110
Free-setting V/f frequency (6)
"free-setting V/f frequency (5)" to "free-setting V/f frequency (7)" (Hz)
0.
Not
Not
b111
Free-setting V/f voltage (6)
0.0 to 800.0 (V)
0.0
Not
Not
b112
Free-setting V/f frequency (7)
"free-setting V/f frequency (6)" (Hz) to 400. (Hz)
0.
Not
Not
b113
Free-setting V/f voltage (7)
0.0 to 800.0 (V)
0.0
Not
Not
Brake control
b120
Brake control enable
00 (disabling), 01 (enabling)
00
Not
Allowed
b121
Brake wait time for release
0.00 to 5.00 (s)
0.00
Not
Allowed
b122
Brake wait time for acceleration
0.00
Not
Allowed
b123
Brake wait time for stopping
0.00
Not
Allowed
b124
Brake wait time for confirmation
0.00
Not
Allowed
b125
Brake release frequency setting
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
b126
Brake release current setting
0.00 x "rated current" to 2.00 x "rated current" (A)
Rated current
Not
Allowed
b127
Braking frequency
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
Overvoltage suppression
b130
Overvoltage suppression enable
00 (disabling restraint), 01 (controlled deceleration),
02 (enabling acceleration with decelerating), 03 (enabling acceleration)
00
Not
Allowed
b131
Overvoltage suppression level
330 to 390 (V) (200 V class), 660 to 780 (V) (400 V class)
380/760
Not
Allowed
b132
Acceleration and deceleration rate at
overvoltage suppression
0.10 to 30.00 (s)
1.00
Not
Allowed
b133
Overvoltage suppression proportional gain
0.00 to 2.55
0.50
Allowed
Allowed
b134
Overvoltage suppression Integral time
0.000 to 9.999 / 10.00 to 65.53 (s)
0.060
Allowed
Allowed
Others
b141
Output loss detection enable
00 (disabling), 01 (enabling)
00
Not
Allowed
b142
Output loss detection sensibility
1.~100.(%)
10.
Allowed
Allowed
b164
Automatic return to initial display
00 (disabling), 01 (enabling)
00
Allowed
Allowed
b166
Data Read/Write select
00 (Read/Write OK), 01 (Protected)
00
Not
Allowed
b180
Initialization trigger
00 (Initialization disable), 01 (Perform initialization)
00
Not
Not
(Note) < >indicate the setting range of 75 to 150kW
(Note) CT : Constant torque mode, VT : variable torque mode, you can set CT or VT by b049.
4 - 9
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
Intelligent input terminals
C001
Terminal [1] function (*2)
01 (RV: Reverse RUN), 02 (CF1: Multispeed 1 setting),
03 (CF2: Multispeed 2 setting),
04 (CF3: Multispeed 3 setting),
05 (CF4: Multispeed 4 setting), 06 (JG: Jogging),
07 (DB: external DC braking),
08 (SET: Set 2nd motor data),
09 (2CH: 2-stage acceleration/deceleration),
11 (FRS: free-run stop), 12 (EXT: external trip),
13 (USP: unattended start protection),
14: (CS: commercial power source enable),
15 (SFT: software lock),
16 (AT: analog input voltage/current select),
17 (SET3: 3rd motor control), 18 (RS: reset),
20 (STA: starting by 3-wire input),
21 (STP: stopping by 3-wire input),
22 (F/R: forward/reverse switching by 3-wire input),
23 (PID: PID disable), 24 (PIDC: PID reset),
26 (CAS: control gain setting),
27 (UP: remote control UP function),
28 (DWN: remote control DOWN function),
29 (DWN: remote control data clearing),
31 (OPE: forcible operation), 32 (SF1: multispeed bit 1),
33 (SF2: multispeed bit 2), 34 (SF3: multispeed bit 3),
35 (SF4: multispeed bit 4), 36 (SF5: multispeed bit 5),
37 (SF6: multispeed bit 6), 38 (SF7: multispeed bit 7),
39 (OLR: overload restriction selection),
40 (TL: torque limit enable),
41 (TRQ1: torque limit selection bit 1),
42 (TRQ2: torque limit selection bit 2),
43 (PPI: P/PI mode selection), 44(BOK:braking confirmation),
46 (LAC: LAD cancellation),
47(PCLR:clearance of position deviation)
48(STAT:pulse train position command input enable)
50 (ADD: trigger for frequency addition [A145]),
51 (F-TM: forcible-terminal operation),
52(ATR:permision of torque command input),
53 (KHC: cumulative power clearance),
54(SON:servo-on), 55(FOC:pre-excitation),
56 (MI1: general-purpose input 1),
57 (MI2: general-purpose input 2),
58 (MI3: general-purpose input 3),
59 (MI4: general-purpose input 4),
60 (MI5: general-purpose input 5),
61 (MI6: general-purpose input 6),
62 (MI7: general-purpose input 7),
63 (MI8: general-purpose input 8),
64(EMR: Emergency stop signal),
65 (AHD: analog command holding),
66(CP1:multi stage position settings selection 1),
67(CP2:multi stage position settings selection 2),
68(CP3:multi stage position settings selection 3),
69(ORL:Zero-return limit function),
70(ORG:Zero-return trigger function),
71(FOT:forward drive stop),72(ROT:reverce drive stop),
73(SPD:speed/position switching),
74 (PCNT: pulse counter), 75 (PCC: pulse counter clear),
82(PRG:EzSQ program-run terminal),
no (NO: no assignment)
18
(*)
Not
Allowed
C002
Terminal [2] function
16
Not
Allowed
C003
Terminal [3] function (*2)
06
(*)
Not
Allowed
C004
Terminal [4] function
11
Not
Allowed
C005
Terminal [5] function
09
Not
Allowed
C006
Terminal [6] function
03
03
13
Not
Allowed
C007
Terminal [7] function
02
Not
Allowed
C008
Terminal [8] function
01
Not
Allowed
C011
Terminal [1] active state
00 (NO) / 01 (NC)
00
Not
Allowed
C012
Terminal [2] active state
00 (NO) / 01 (NC)
00
Not
Allowed
C013
Terminal [3] active state
00 (NO) / 01 (NC)
00
Not
Allowed
C014
Terminal [4] active state
00 (NO) / 01 (NC)
00
Not
Allowed
C015
Terminal [5] active state
00 (NO) / 01 (NC)
00
Not
Allowed
C016
Terminal [6] active state
00 (NO) / 01 (NC)
00
Not
Allowed
C017
Terminal [7] active state
00 (NO) / 01 (NC)
00
Not
Allowed
C018
Terminal [8] active state
00 (NO) / 01 (NC)
00
Not
Allowed
C019
Terminal [FW] active state
00 (NO) / 01 (NC)
00
Not
Allowed
(*) When the emergency stop function is enabled (SW1 = ON), "18" (RS) and "64" (EMR) are forcibly written to parameters "C001" and "C003", respectively. (You
cannot arbitrarily write "64" to "C001".) If the SW1 signal is turned off and then turned on, "no" (no assignment) is set in parameter "C003".
4 - 10
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
Intelligent output terminals
C021
Terminal [11] function
00 (RUN: running), 01 (FA1: constant-speed reached),
02 (FA2: set frequency overreached),
03 (OL: overload notice advance signal (1)),
04 (OD: output deviation for PID control),
05 (AL: alarm signal),
06 (FA3: set frequency reached), 07 (OTQ: over-torque),
08 (IP: instantaneous power failure),
09 (UV: under voltage), 10 (TRQ: torque limited),
11 (RNT: operation time over), 12 (ONT: plug-in time over),
13 (THM: thermal alarm signal), 19(BRK:brakge release),
20(BER:braking error)21 (ZS: 0 Hz detection signal),
22(DSE:speed deviation maximum),
23(POK:positioning completed),
24 (FA4: set frequency overreached 2),
25 (FA5: set frequency reached 2),
26 (OL2: overload notice advance signal (2)),
27 (Odc: Analog O disconnection detection),
28 (OIDc: Analog OI disconnection detection),
29 (O2Dc: Analog O2 disconnection detection),
31 (FBV: PID feedback comparison),
32 (NDc: communication line disconnection),
33 (LOG1: logical operation result 1),
34 (LOG2: logical operation result 2),
35 (LOG3: logical operation result 3),
36 (LOG4: logical operation result 4),
37 (LOG5: logical operation result 5),
38 (LOG6: logical operation result 6),
39 (WAC: capacitor life warning),
40 (WAF: cooling-fan speed drop),
41 (FR: starting contact signal),
42 (OHF: heat sink overheat warning),
43 (LOC: low-current indication signal),
44 (M01: general-purpose output 1),
45 (M02: general-purpose output 2),
46 (M03: general-purpose output 3),
47 (M04: general-purpose output 4),
48 (M05: general-purpose output 5),
49 (M06: general-purpose output 6),
50 (IRDY: inverter ready), 51 (FWR: forward rotation),
52 (RVR: reverse rotation), 53 (MJA: major failure),
54(WCO: window comparator O),
55(WCOI: window comparator OI),
56 (WCO2: window comparator O2)
(When alarm code output is selected for "C062", functions "AC0" to
"AC2" or "AC0" to "AC3" [ACn: alarm code output] are forcibly
assigned to intelligent output terminals 11 to 13 or 11 to 14,
respectively.)
01
Not
Not
C022
Terminal [12] function
00
Not
Not
C023
Terminal [13] function
03
Not
Not
C024
Terminal [14] function
07
Not
Not
C025
Terminal [15] function
40
Not
Not
C026
Alarm relay terminal function
05
Not
Not
Analog monitoring
C027
[FM] signal selection
00 (output frequency), 01 (output current),
02 (output torque), 03 (digital output frequency),
04 (output voltage), 05 (input power),
06 (electronic thermal overload), 07 (LAD frequency),
08 (digital current monitoring), 09 (motor temperature),
10 (heat sink temperature), 12 (general-purpose output YA0)
00
Not
Not
C028
[AM] signal selection
00 (output frequency), 01 (output current),
02 (output torque), 04 (output voltage), 05 (input power), 06
(electronic thermal overload), 07 (LAD frequency),
09 (motor temperature), 10 (heat sink temperature),
11 (output torque [signed value]), 13 (general-purpose output YA1)
00
Not
Not
C029
[AMI] signal selection
00 (output frequency), 01 (output current),
02 (output torque), 04 (output voltage), 05 (input power), 06
(electronic thermal overload), 07 (LAD frequency),
09 (motor temperature), 10 (heat sink temperature),
14 (general-purpose output YA2)
00
Not
Not
C030
Digital current monitor reference
value
0.20 x "rated current" to 1.50 x "rated current" (A)
(Current with digital current monitor output at 1,440 Hz)
Rated current
Allowed
Allowed
Intelligent output terminals
C031
Terminal [11] active state
00 (NO) / 01 (NC)
00
Not
Not
C032
Terminal [12] active state
00 (NO) / 01 (NC)
00
Not
Not
C033
Terminal [13] active state
00 (NO) / 01 (NC)
00
Not
Not
C034
Terminal [14] active state
00 (NO) / 01 (NC)
00
Not
Not
C035
Terminal [15] active state
00 (NO) / 01 (NC)
00
Not
Not
C036
Alarm relay active state
00 (NO) / 01 (NC)
01
Not
Not
4 - 11
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
Levels and output terminal status
C038
Low-current indication signal output mode
selection
00 (output during acceleration/deceleration and constant-speed
operation),
01 (output only during constant-speed operation)
01
Not
Allowed
C039
Low-current indication signal detection level
0.00 to 2.00 x "rated current" (A)
<0.00 to 1.80 x "rated current" (A) > (In case of CT)
0.00 to 1.50 x "rated current" (A) (In case of VT)
Rated
current
Allowed
Allowed
C040
Overload signal output mode
00 (output during acceleration/deceleration and constant-speed
operation),
01 (output only during constant-speed operation)
01
Not
Allowed
C041
Overload level setting
0.00 to 2.00 x "rated current" (A)
<0.00 to 1.80 x "rated current" (A) > (In case of CT)
0.00 to 1.50 x "rated current" (A) (In case of VT)
Rated
current
Allowed
Allowed
C042
Frequency arrival setting for accel.
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
C043
Frequency arrival setting for decel.
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
C044
PID deviation level setting
0.0 to 100.0 (%)
3.0
Not
Allowed
C045
Frequency arrival setting for acceleration (2)
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
C046
Frequency arrival setting for deceleration (2)
0.00 to 99.99, 100.0 to 400.0 (Hz)
0.00
Not
Allowed
C052
Maximum PID feedback data
0.0 to 100.0 (%)
100.0
Not
Allowed
C053
Minimum PID feedback data
0.0 to 100.0 (%)
0.0
Not
Allowed
C055
Over-torque (forward-driving) level setting
0. to 200. (%), no (disabling torque limitation)
<0. to 150. (%), no (disabling torque limitation)> (In case of CT)
0. to 150. (%), no (disabling torque limitation)(In case of VT)
100.
Not
Allowed
C056
Over-torque (reverse regenerating) level
setting
100.
Not
Allowed
C057
Over-torque (reverse driving) level setting
100.
Not
Allowed
C058
Over-torque (forward regenerating) level
setting
100.
Not
Allowed
C061
Electronic thermal warning level setting
0. to 100. (%)
80.
Not
Allowed
C062
Alarm code output
00 (disabling), 01 (3 bits), 02 (4 bits)
00
Not
Allowed
C063
Zero speed detection level
0.00 to 99.99, 100.0 (Hz)
0.00
Not
Allowed
C064
Heat sink overheat warning level
0. to 200.0 (C)
120.
Not
Allowed
Communication function
C071
Communication speed selection
02 (loopback test), 03(2400bps), 04(4800bps),
05(9600bps), 06(19.2kbps), 07(38.4kbps),
08(57.6kbps), 09(76.8kbps), 10(115.2kbps)
04
Not
Allowed
C072
Node allocation
1. to 32.
1.
Not
Allowed
C073
Communication data length selection
7 (7 bits), 8 (8 bits)
7
Not
Allowed
C074
Communication parity selection
00 (no parity), 01 (even parity), 02 (odd parity)
00
Not
Allowed
C075
Communication stop bit selection
1 (1 bit), 2 (2 bits)
1
Not
Allowed
C076
Selection of the operation after
communication error
00 (tripping),
01 (tripping after decelerating and stopping the motor),
02 (ignoring errors),
03 (stopping the motor after free-running),
04 (decelerating and stopping the motor)
02
Not
Allowed
C077
Communication timeout limit before tripping
0.00 to 99.99 (s)
0.00
Not
Allowed
C078
Communication wait time
0. to 1000. (ms)
0.
Not
Allowed
C079
Communication mode selection
00(ASCII), 01(Modbus-RTU)
00
Not
Allowed
Adjustment
C081
[O] input span calibration
0. to 9999., 1000 to 6553(10000 to 65530)
Factory
setting
Allowed
Allowed
C082
[OI] input span calibration
Factory
setting
Allowed
Allowed
C083
[O2] input span calibration
Factory
setting
Allowed
Allowed
C085
Thermistor input tuning
0.0 to 999.9, 1000.
Factory
setting
Allowed
Allowed
C091
Debug mode enable
(Do not change this parameter, which is intended for factory
adjustment.)
00
Not
Not
Others
C101
Up/Down memory mode selection
00 (not storing the frequency data),
01 (storing the frequency data)
00
Not
Allowed
C102
Reset mode selection
00 (resetting the trip when RS is on),
01 (resetting the trip when RS is off),
02 (enabling resetting only upon tripping [resetting when RS is
on]), 03(resetting only trip)
00
Allowed
Allowed
C103
Restart mode after reset
00 (starting with 0 Hz), 01 (starting with matching frequency),
02 (restarting with active matching frequency)
00
Not
Allowed
Meter
adjustment
C105
FM gain adjustment
50. to 200. (%)
100.
Allowed
Allowed
C106
AM gain adjustment
100.
Allowed
Allowed
C107
AMI gain adjustment
100.
Allowed
Allowed
C109
AM bias adjustment
0. to 100. (%)
0.
Allowed
Allowed
C110
AMI bias adjustment
20.
Allowed
Allowed
(Note) < >indicate the setting range of 75 to 150kW
(Note) CT : Constant torque mode, VT : variable torque mode, you can set CT or VT by b049.
4 - 12
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
Terminal
C111
Overload setting (2)
0.20 to 2.00 x "rated current" (A)
<0.20 to 1.80 x "rated current" (A) > (In case of CT)
0.20 to 1.50 x "rated current" (A) (In case of VT)
Rated current
Allowed
Allowed
Adjustm
ent
C121
[O] input zero calibration
0. to 9999., 1000 to 6553 (10000 to 65530)
Factory setting
Allowed
Allowed
C122
[OI] input zero calibration
Factory setting
Allowed
Allowed
C123
[O2] input zero calibration
Factory setting
Allowed
Allowed
Output terminal operation function
C130
Output 11 on-delay time
0.0 to 100.0 (s)
0.0
Not
Allowed
C131
Output 11 off-delay time
0.0
Not
Allowed
C132
Output 12 on-delay time
0.0 to 100.0 (s)
0.0
Not
Allowed
C133
Output 12 off-delay time
0.0
Not
Allowed
C134
Output 13 on-delay time
0.0 to 100.0 (s)
0.0
Not
Allowed
C135
Output 13 off-delay time
0.0
Not
Allowed
C136
Output 14 on-delay time
0.0 to 100.0 (s)
0.0
Not
Allowed
C137
Output 14 off-delay time
0.0
Not
Allowed
C138
Output 15 on-delay time
0.0 to 100.0 (s)
0.0
Not
Allowed
C139
Output 15 off-delay time
0.0
Not
Allowed
C140
Output RY on-delay time
0.0 to 100.0 (s)
0.0
Not
Allowed
C141
Output RY off-delay time
0.0
Not
Allowed
C142
Logical output signal 1 selection 1
Same as the settings of C021 to C026
(except those of LOG1 to LOG6)
00
Not
Allowed
C143
Logical output signal 1 selection 2
00
Not
Allowed
C144
Logical output signal 1 operator selection
00 (AND), 01 (OR), 02 (XOR)
00
Not
Allowed
C145
Logical output signal 2 selection 1
Same as the settings of C021 to C026
(except those of LOG1 to LOG6)
00
Not
Allowed
C146
Logical output signal 2 selection 2
00
Not
Allowed
C147
Logical output signal 2 operator selection
00 (AND), 01 (OR), 02 (XOR)
00
Not
Allowed
C148
Logical output signal 3 selection 1
Same as the settings of C021 to C026
(except those of LOG1 to LOG6)
00
Not
Allowed
C149
Logical output signal 3 selection 2
00
Not
Allowed
C150
Logical output signal 3 operator selection
00 (AND), 01 (OR), 02 (XOR)
00
Not
Allowed
C151
Logical output signal 4 selection 1
Same as the settings of C021 to C026
(except those of LOG1 to LOG6)
00
Not
Allowed
C152
Logical output signal 4 selection 2
00
Not
Allowed
C153
Logical output signal 4 operator selection
00 (AND), 01 (OR), 02 (XOR)
00
Not
Allowed
C154
Logical output signal 5 selection 1
Same as the settings of C021 to C026
(except those of LOG1 to LOG6)
00
Not
Allowed
C155
Logical output signal 5 selection 2
00
Not
Allowed
C156
Logical output signal 5 operator selection
00 (AND), 01 (OR), 02 (XOR)
00
Not
Allowed
C157
Logical output signal 6 selection 1
Same as the settings of C021 to C026
(except those of LOG1 to LOG6)
00
Not
Allowed
C158
Logical output signal 6 selection 2
00
Not
Allowed
C159
Logical output signal 6 operator selection
00 (AND), 01 (OR), 02 (XOR)
00
Not
Allowed
Input terminal response
C160
Input terminal response time setting 1
0. to 200. ( 2ms)
1
Not
Allowed
C161
Input terminal response time setting 2
0. to 200. ( 2ms)
1
Not
Allowed
C162
Input terminal response time setting 3
0. to 200. ( 2ms)
1
Not
Allowed
C163
Input terminal response time setting 4
0. to 200. ( 2ms)
1
Not
Allowed
C164
Input terminal response time setting 5
0. to 200. ( 2ms)
1
Not
Allowed
C165
Input terminal response time setting 6
0. to 200. ( 2ms)
1
Not
Allowed
C166
Input terminal response time setting 7
0. to 200. ( 2ms)
1
Not
Allowed
C167
Input terminal response time setting 8
0. to 200. ( 2ms)
1
Not
Allowed
C168
Input terminal response time setting FW
0. to 200. ( 2ms)
1
Not
Allowed
Other
C169
Multistage speed/position determination time
0. to 200. ( 10ms)
0
Not
Allowed
(Note) < >indicate the setting range of 75 to 150kW
4 - 13
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
Control constants
H001
Auto-tuning Setting
00 (disabling auto-tuning),
01 (auto-tuning without rotation),
02 (auto-tuning with rotation)
00
Not
Not
H002
Motor data selection, 1st motor
00 (Hitachi standard data), 01 (auto-tuned data),
02 (auto-tuned data [with online auto-tuning function])
00
Not
Not
H202
Motor data selection, 2nd motor
00
Not
Not
H003
Motor capacity, 1st motor
0.20 to 160. (kW)
Factory setting
Not
Not
H203
Motor capacity, 2nd motor
Factory setting
Not
Not
H004
Motor poles setting, 1st motor
2, 4, 6, 8, 10 (poles)
4
Not
Not
H204
Motor poles setting, 2nd motor
4
Not
Not
H005
Motor speed constant, 1st motor
0.001 to 9.999, 10.00 to 80.00 (10.000 to 80.000)
1.590
Allowed
Allowed
H205
Motor speed constant, 2nd motor
1.590
Allowed
Allowed
H006
Motor stabilization constant, 1st motor
0. to 255.
100.
Allowed
Allowed
H206
Motor stabilization constant, 2nd motor
100.
Allowed
Allowed
H306
Motor stabilization constant, 3rd motor
100.
Allowed
Allowed
H020
Motor constant R1, 1st motor
0.001 to 9.999, 10.00 to 65.53 ()
Factory setting
Not
Not
H220
Motor constant R1, 2nd motor
Factory setting
Not
Not
H021
Motor constant R2, 1st motor
0.001 to 9.999, 10.00 to 65.53 ()
Factory setting
Not
Not
H221
Motor constant R2, 2nd motor
Factory setting
Not
Not
H022
Motor constant L, 1st motor
0.01 to 99.99, 100.0 to 655.3 (mH)
Factory setting
Not
Not
H222
Motor constant L, 2nd motor
Factory setting
Not
Not
H023
Motor constant Io
0.01 to 99.99, 100.0 to 655.3 (A)
Factory setting
Not
Not
H223
Motor constant Io, 2nd motor
Factory setting
Not
Not
H024
Motor constant J
0.001 to 9.999, 10.00 to 99.99, 100.0 to 999.9,
1000. to 9999.
Factory setting
Not
Not
H224
Motor constant J, 2nd motor
Factory setting
Not
Not
H030
Auto constant R1, 1st motor
0.001 to 9.999, 10.00 to 65.53 ()
Factory setting
Not
Not
H230
Auto constant R1, 2nd motor
Factory setting
Not
Not
H031
Auto constant R2, 1st motor
0.001 to 9.999, 10.00 to 65.53 ()
Factory setting
Not
Not
H231
Auto constant R2, 2nd motor
Factory setting
Not
Not
H032
Auto constant L, 1st motor
0.01 to 99.99, 100.0 to 655.3 (mH)
Factory setting
Not
Not
H232
Auto constant L, 2nd motor
Factory setting
Not
Not
H033
Auto constant Io, 1st motor
0.01 to 99.99, 100.0 to 655.3 (A)
Factory setting
Not
Not
H233
Auto constant Io, 2nd motor
Factory setting
Not
Not
H034
Auto constant J, 1st motor
0.001 to 9.999, 10.00 to 99.99, 100.0 to 999.9,
1000. to 9999.
Factory setting
Not
Not
H234
Auto constant J, 2nd motor
Factory setting
Not
Not
H050
PI proportional gain for 1st motor
0.0 to 999.9, 1000.
100.0
Allowed
Allowed
H250
PI proportional gain for 2nd motor
100.0
Allowed
Allowed
H051
PI integral gain for 1st motor
0.0 to 999.9, 1000.
100.0
Allowed
Allowed
H251
PI integral gain for 2nd motor
100.0
Allowed
Allowed
H052
P proportional gain setting for
1st motor
0.01 to 10.00
1.00
Allowed
Allowed
H252
P proportional gain setting for
2nd motor
1.00
Allowed
Allowed
H060
Zero level limit for 1st motor
0.0 to 100.0
100.0
Allowed
Allowed
H260
Zero level limit for 2nd motor
100.0
Allowed
Allowed
H061
Zero level starting boost current for 1st
motor
0. to 50. (%)
50.
Allowed
Allowed
H261
Zero level starting boost current for 2nd
motor
50.
Allowed
Allowed
H070
Terminal selection PI proportional gain
setting
0.0 to 999.9, 1000.
100.0
Allowed
Allowed
H071
Terminal selection PI integral gain setting
100.0
Allowed
Allowed
H072
Terminal selection P proportional gain
setting
0.00 to 10.00
1.00
Allowed
Allowed
H073
Gain switching time
0. to 9999. (ms)
100.
Allowed
Allowed
4 - 14
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
Optional functions
P001
Operation mode on expansion card 1 error
00 (tripping), 01 (continuing operation)
00
Not
Allowed
P002
Operation mode on expansion card 2 error
00
Not
Allowed
P011
Encoder pulse-per-revolution (PPR) setting
128. to 9999., 1000 to 6500 (10000 to 65000) (pulses)
1024.
Not
Not
P012
Control pulse setting
00 (ASR), 01 (APR), 02 (APR2), 03 (HAPR)
00
Not
Not
P013
Pulse input mode setting
00 (mode 0), 01 (mode 1), 02 (mode 2)
00
Not
Not
P014
Home search stop position setting
0. to 4095.
0.
Not
Allowed
P015
Home search speed setting
"start frequency" to "maximum frequency"
(up to 120.0) (Hz)
5.00
Not
Allowed
P016
Home search direction setting
00 (forward), 01 (reverse)
00
Not
Allowed
P017
Home search completion range setting
0. to 9999., 1000 (10000) (pulses)
5.
Not
Allowed
P018
Home search completion delay time setting
0.00 to 9.99 (s)
0.00
Not
Allowed
P019
Electronic gear set position selection
00 (feedback side), 01 (commanding side)
00
Not
Allowed
P020
Electronic gear ratio numerator setting
1. to 9999.
1.
Allowed
Allowed
P021
Electronic gear ratio denominator setting
1. to 9999.
1.
Allowed
Allowed
P022
Feed-forward gain setting
0.00 to 99.99, 100.0 to 655.3
0.00
Allowed
Allowed
P023
Position loop gain setting
0.00 to 99.99, 100.0
0.50
Allowed
Allowed
P024
Position bias setting
-204 (-2048.) / -999. to 2048
0.
Allowed
Allowed
P025
Temperature compensation thermistor enable
00 (no compensation), 01 (compensation)
00
Not
Allowed
P026
Over-speed error detection level setting
0.0 to 150.0 (%)
135.0
Not
Allowed
P027
Speed deviation error detection level setting
0.00 to 99.99, 100.0 to120.0 (Hz)
7.50
Not
Allowed
P028
Numerator of motor gear ratio
1. to 9999.
1.
Not
Allowed
P029
Denominator of motor gear ratio
1. to 9999.
1.
Not
Allowed
P031
Accel/decel time input selection
00 (digital operator), 01 (option 1), 02 (option 2),
03 (easy sequence)
00
Not
Not
P032
Positioning command input selection
00 (digital operator), 01 (option 1), 02 (option 2)
00
Not
Allowed
P033
Torque command input selection
00 (O terminal), 01 (OI terminal), 02 (O2 terminal),
03 (digital operator)
00
Not
Not
P034
Torque command setting
0. to 200. (%) <0. to 180. (%)>
0.
Allowed
Allowed
P035
Polarity selection at the torque command
input via O2 terminal
00 (as indicated by the sign),
01 (depending on the operation direction)
00
Not
Not
P036
Torque bias mode
00 (disabling the mode), 01 (digital operator),
02 (input via O2 terminal)
00
Not
Not
P037
Torque bias value
-200. to +200. (%) <-180. to +180. (%)>
0.
Allowed
Allowed
P038
Torque bias polarity selection
00 (as indicated by the sign),
01 (depending on the operation direction)
00
Not
Not
P039
Speed limit for torque-controlled operation
(forward rotation)
0.00 to "maximum frequency" (Hz)
0.00
Allowed
Allowed
P040
Speed limit for torque-controlled operation
(reverse rotation)
0.00
Allowed
Allowed
P044
DeviceNet comm watchdog timer
0.00 to 99.99 (s)
1.00
Not
Not
P045
Inverter action on DeviceNet comm error
00 (tripping),
01 (tripping after decelerating and stopping the motor),
02 (ignoring errors),
03 (stopping the motor after free-running),
04 (decelerating and stopping the motor)
01
Not
Not
P046
DeviceNet polled I/O: Output instance
number
20, 21, 100
21
Not
Not
P047
DeviceNet polled I/O: Input instance number
70, 71, 101
71
Not
Not
P048
Inverter action on DeviceNet idle mode
00 (tripping),
01 (tripping after decelerating and stopping the motor),
02 (ignoring errors),
03 (stopping the motor after free-running),
04 (decelerating and stopping the motor)
01
Not
Not
P049
DeviceNet motor poles setting for RPM
0, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26,
28, 30, 32, 34, 36, 38 (poles)
0
Not
Not
(Note) < >indicate the setting range of 75 to 150kW
4 - 15
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
Output
pulse
P055
Pulse-string frequency scale
1.0 to 50.0 (kHz)
25.0
Not
Allowed
P056
Time constant of pulse-string frequency filter
0.01 to 2.00 (s)
0.10
Not
Allowed
P057
Pulse-string frequency bias
-100. to +100. (%)
0.
Not
Allowed
P058
Pulse-string frequency limit
0. to 100. (%)
100.
Not
Allowed
Absolute position control
P060
Multistage position setting 0
Position setting range reverse side – forward side
(upper 4 digits including “-“)
0
Allowed
Allowed
P061
Multistage position setting 1
Position setting range reverse side – forward side
(upper 4 digits including “-“)
0
Allowed
Allowed
P062
Multistage position setting 2
Position setting range reverse side – forward side
(upper 4 digits including “-“)
0
Allowed
Allowed
P063
Multistage position setting 3
Position setting range reverse side – forward side
(upper 4 digits including “-“)
0
Allowed
Allowed
P064
Multistage position setting 4
Position setting range reverse side – forward side
(upper 4 digits including “-“)
0
Allowed
Allowed
P065
Multistage position setting 5
Position setting range reverse side – forward side
(upper 4 digits including “-“)
0
Allowed
Allowed
P066
Multistage position setting 6
Position setting range reverse side – forward side
(upper 4 digits including “-“)
0
Allowed
Allowed
P067
Multistage position setting 7
Position setting range reverse side – forward side
(upper 4 digits including “-“)
0
Allowed
Allowed
P068
Zero-return mode selection
00(Low)/01 (Hi1)/00 (Hi2)
00
Allowed
Allowed
P069
Zero-return direction selection
00 (FW)/01 (RV)
00
Allowed
Allowed
P070
Low-speed zero-return frequency
0.00 to 10.00 (Hz)
0.00
Allowed
Allowed
P071
High-speed zero-return frequency
0.00 – 99.99 / 100.0 – Maximum frequency setting, 1st
motor (Hz)
0.00
Allowed
Allowed
P072
Position range specification (forward)
0 – 268435455 (when P012 = 02)
0 – 1073741823 (When P012 = 03) (upper 4 digits)
2684
(268435455)
Allowed
Allowed
P073
Position range specification (reverse)
-268435455 – 0 (when P012 = 02)
-1073741823 - 0 (When P012 = 03) (upper 4 digits)
-268
(-268435455)
Allowed
Allowed
P074
Teaching selection
00 (X00) / 01 (X01) / 02 (X02) / 03 (X03) /04 (X04) / 05
(X05) / 06 (X06) / 07 (X07)
00
Allowed
Allowed
Easy sequence function
P100
Easy sequence user parameter U (00)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P101
Easy sequence user parameter U (01)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P102
Easy sequence user parameter U (02)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P103
Easy sequence user parameter U (03)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P104
Easy sequence user parameter U (04)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P105
Easy sequence user parameter U (05)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P106
Easy sequence user parameter U (06)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P107
Easy sequence user parameter U (07)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P108
Easy sequence user parameter U (08)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P109
Easy sequence user parameter U (09)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P110
Easy sequence user parameter U (10)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
4 - 16
Chapter 4 List of Data Settings
Code
Function name
Monitored data or setting
Default
Change during
RUN operation
FF
FEF
FUF
b031≠10
b031=10
Easy sequence function
P111
Easy sequence user parameter U (11)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P112
Easy sequence user parameter U (12)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P113
Easy sequence user parameter U (13)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P114
Easy sequence user parameter U (14)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P115
Easy sequence user parameter U (15)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P116
Easy sequence user parameter U (16)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P117
Easy sequence user parameter U (17)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P118
Easy sequence user parameter U (18)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P119
Easy sequence user parameter U (19)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P120
Easy sequence user parameter U (20)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P121
Easy sequence user parameter U (21)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P122
Easy sequence user parameter U (22)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P123
Easy sequence user parameter U (23)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P124
Easy sequence user parameter U (24)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P125
Easy sequence user parameter U (25)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P126
Easy sequence user parameter U (26)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P127
Easy sequence user parameter U (27)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P128
Easy sequence user parameter U (28)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P129
Easy sequence user parameter U (29)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P130
Easy sequence user parameter U (30)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
P131
Easy sequence user parameter U (31)
0. to 9999., 1000 to 6553 (10000 to 65535)
0.
Allowed
Allowed
User parameters
U001
User-selected function 1
no/d001 to P131
no
Allowed
Allowed
U002
User-selected function 2
no/d001 to P131
no
Allowed
Allowed
U003
User-selected function 3
no/d001 to P131
no
Allowed
Allowed
U004
User-selected function 4
no/d001 to P131
no
Allowed
Allowed
U005
User-selected function 5
no/d001 to P131
no
Allowed
Allowed
U006
User-selected function 6
no/d001 to P131
no
Allowed
Allowed
U007
User-selected function 7
no/d001 to P131
no
Allowed
Allowed
U008
User-selected function 8
no/d001 to P131
no
Allowed
Allowed
U009
User-selected function 9
no/d001 to P131
no
Allowed
Allowed
U010
User-selected function 10
no/d001 to P131
no
Allowed
Allowed
U011
User-selected function 11
no/d001 to P131
no
Allowed
Allowed
U012
User-selected function 12
no/d001 to P131
no
Allowed
Allowed
(Note) < >indicate the setting range of 75 to 150kW
4 - 17
Chapter 4 List of Data Settings
(Memo)
4 - 18
Chapter 5 Error Codes
This chapter describes the error and warning codes of the inverter.
5.1 Error Codes and Troubleshooting ··········· 5 - 2
5.2 Warning Codes ································ 5 - 5
Chapter 5 Error Codes
Name
Description
Display on
digital operator
Overcurrent
protection
If the motor is constrained or
suddenly accelerated or
decelerated, a high current
will flow in the inverter and
the inverter may fail. To
avoid this problem, the
inverter shuts off its output
and displays the error code
shown on the right when it
detects a current higher than
a specified level.
This protective function uses
a DC current detector to
detect overcurrent.
When a current as high as
about 220% of the inverter's
rated output current of
constant torque mode is
detected, the protective
circuit operates and the
inverter trips.
During
constant-
speed operation
During
deceleration
During
acceleration
Others
Overload
protection
(*1)
This protective function monitors the inverter
output current, and shuts off the inverter
output and displays the error code shown on
the right when the internal electronic thermal
protection circuit detects a motor overload.
If the error occurs, the inverter will trip
according to the setting of the electronic
thermal function.
Braking
resistor
overload
protection
When the BRD operation rate exceeds the
setting of "b090", this protective function
shuts off the inverter output and displays the
error code shown on the right.
Overvoltage
protection
If the DC voltage across the P and N terminals
rises too high, an inverter failure may result.
To avoid this problem, this protective function
shuts off the inverter output and displays the
error code shown on the right when the DC
voltage across the P and N terminals exceeds
a specified level because of an increase in the
energy regenerated by the motor or the input
voltage (during operation).
The inverter will trip if the DC voltage across
the P and N terminals exceeds about 400
VDC (in case of the 200 V class models) or
about 800 VDC (in case of the 400 V class
models).
EEPROM
error
(*2) (*3)
When an internal-EEPROM is caused by
external noise or an abnormal temperature
rise, the inverter shuts off its output and
displays the error code shown on the right.
Note: An EEPROM error may result in a CPU
error.
Under
voltage
If the inverter input voltage drops, the control
circuit of the inverter cannot function
normally. Therefore, the inverter shuts off its
output when the input voltage falls below a
specified level.
The inverter will trip if the DC voltage across
the P and N terminals exceeds about 175
VDC (in case of the 200 V class models) or
about 345 VDC (in case of the 400 V class
models).
Name
Description
Display on
digital operator
CT error
If an error occurs in the internal current
detector (CT), the inverter will shut off its
output and display the error code shown on
the right. The inverter will trip when the CT
outputs about 0.6 V or more at power-on.
CPU error (*3)
If the internal CPU malfunctions or an error
occurs in it, the inverter will shut off its
output and display the error code shown on
the right.
Note: Reading an abnormal data from the
EEPROM may result in a CPU error.
External trip
If an error occurs in the external equipment
or device connected to the inverter, the
inverter will fetch the error signal and shut
off its output. (This protective function is
enabled when the external trip function is
enabled.)
USP error
A USP error is indicated when the inverter
power is turned on with an input operation
signal remaining in the inverter. (This
protective function is enabled when the USP
function is enabled.)
Ground-fault
protection (*3)
When the inverter power is turned on, this
protective function detects the ground fault
between the inverter output circuit and the
motor to protect the inverter. (This function
does not operate when a residual voltage
remains in the motor.)
Input
overvoltage
protection
This protective function determines an error
if the input voltage is kept above the
specification level for 100 seconds while the
inverter is stopped.
The inverter will trip if the DC voltage of
the main circuit is kept above about 390
VDC (in case of the 200 V class models) or
about 780 VDC (in case of the 400 V class
models).
Instanta-
neous power
failure
protection
If an instantaneous power failure lasts 15 ms
or more, the inverter will shut off its output.
When the power failure duration is long, the
inverter assumes a normal power-off. If a
restart mode has been selected and an
operation command remains in the inverter,
the inverter will restart after the power is
recovered.
Temperature
error due to
low
cooling-fan
speed
The inverter will display the error code
shown on the right if the lowering of
cooling-fan speed is detected at the
occurrence of the temperature error
described below.
Temperature
error
If the main circuit temperature rises because
of a high ambient temperature or for other
reasons, the inverter will shut off its output.
5.1 Error Codes and Troubleshooting
5.1.1 Error Codes
*1 The inverter will not accept any reset command within about 10 seconds after tripping (i.e., after the protective function operates).
*2 The inverter will not accept any reset command after an EEPROM error occurs with error code displayed. Turn off the inverter
power once. If error code "E08" is displayed when the inverter power is turned on subsequently, the internal memory device may have failed
or parameters may have not been stored correctly. In such cases, initialize the inverter, and then re-set the parameters.
*3 The inverter will not accept reset commands input via the RS terminal or entered by the STOP/RESET key. Therefore, turn off the inverter
power.
5 - 2
Chapter 5 Error Codes
to
to
Name
Description
Display on
digital operator
User Trip
The inverter detects errors in the easy
sequence. Refer to SJ700D-3 instruction
manual.
Option 1 error
The inverter detects errors in the option
board mounted in the optional slot 1. For
details, refer to the instruction manual for
the mounted option board.
Option 2 error
The inverter detects errors in the option
board mounted in the optional slot 1. For
details, refer to the instruction manual for
the mounted option board.
Waiting in
under voltage
status
If the input voltage falls, the inverter will
shut off its output, display the code shown
on the right, and wait for the recovery of
the input voltage.
The inverter will display the same error
code also during an instantaneous power
failure.
(remark) Inverter trips with under voltage
when this status continues for 40 seconds.
Communica-
tion error
If a problem occurs in the communication
between the digital operator and inverter,
the inverter will display the code shown on
the right. For example disconnection.
Waiting for
retry
When the retry after instantaneous power
failure or tripping has been enabled, the
inverter displays the code shown on the
right while awaiting retry after an
instantaneous power failure or tripping.
Power-off
The inverter displays the code shown on
the right when the inverter power is turned
off.
Restricted
operation
command
When an operation direction has been
restricted by the setting of "b035", the
inverter will display the error code shown
on the right if the operation command
specifying the restricted operation direction
is input.
Empty trip
history
If the inverter has not tripped before, the
inverter displays .
Name
Description
Display on
digital operator
Gate array
communica-
tion error
If an error occurs in the communication
between the internal CPU and gate array, the
inverter will trip.
Phase loss
input
protection
When the phase loss input protection has
been enabled (b006 = 01), the inverter will
trip to avoid damage if an phase loss input is
detected. The inverter trips when the phase
loss input continues for about 1 second or
more.
Main circuit
error (*4)
The inverter will trip if the gate array cannot
confirm the on/off state of IGBT because of
a malfunction due to noise,short or damage
to the main circuit element.
IGBT error
If instantaneous overcurrent occurs, the main
circuit element temperature is abnormal, or
the main circuit element drive power drops,
the inverter will shut off its output to protect
the main circuit element. (After tripping
because of this protective function, the
inverter cannot retry the operation.)
Phase loss
output
protection
When the phase loss output protection has
been enabled (b141 = 01), the inverter will
trip to avoid damage if an phase loss output
is detected. The inverter can detect an phase
loss when the output frequency is from 5 Hz
to 100 Hz.
Thermistor
error
The inverter monitors the resistance of the
thermistor (in the motor) connected to the
inverter's TH terminal, and will shut off the
inverter output if the motor temperature
rises.
Emergency
stop (*5)
If the EMR signal (on three terminals) is
turned on when the slide switch (SW1) on
the logic board is set to ON, the inverter
hardware will shut off the inverter output
and display the error code shown on the
right.
Malfunction due to incoming noise, in case
EMR terminal is not ON.
Low-speed
overload
protection
If overload occurs during the motor
operation at a very low speed at 0.2 Hz or
less, the electronic thermal protection circuit
in the inverter will detect the overload and
shut off the inverter output. (2nd electronic
thermal control)
(Note that a high frequency may be recorded
as the error history data.)
Modbus
communica-
tion error
If timeout occurs because of line
disconnection during the communication in
Modbus-RTU mode, the inverter will display
the error code shown on the right. (The
inverter will trip according to the setting of
"C076".)
Invalid
instruction
The inverter detects errors in the easy
sequence. Refer to SJ700D-3 instruction
manual.
Nesting count
error
Execution
error
to
*4 The inverter will not accept reset commands input via the RS terminal or entered by the STOP/RESET key. Therefore, turn off the inverter
power.
*5 The inverter will not accept the reset command entered from the digital operator. Therefore, reset the inverter by turning on the RS terminal.
5 - 3
Chapter 5 Error Codes
: Resetting/Initialization at power-on or with the reset terminal
turned on
: Stopping the motor
: Decelerating or operating the motor
: During constant speed
: Accelerating the motor
: Status after receiving a zero-frequency operation command
: Starting the motor
: Applying DC braking to the motor
: Overload-restricted operation
: Forcible or servo-on operation
1) Trip factor
These digits indicate a trip factor.
See Section 5.1.1.
This digit indicates the inverter status at tripping.
2) Output frequency (Hz) at tripping
3) Output current (A) at tripping
4) DC voltage (V) across P and N terminals at tripping
5) Accumulated time (h) for which the inverter has
been running before tripping
6) Accumulated time for which the inverter power has
been on before tripping
Explanation of display
Note: The above descriptions indicate the inverter status at the occurrence of
tripping, which may not correspond to the apparent operation of the motor.
(Example)
When the PID control is used or the frequency command is input as an analog
signal (a voltage or current signal), the inverter may repeat acceleration and
deceleration alternately at short intervals to make up for the fluctuations of the
analog signal, even if the motor is apparently running at constant speed.
In such cases, the inverter status at tripping may not correspond to the
apparent operation of the motor.
5.1.2 Trip conditions monitoring
5 - 4
Chapter 5 Error Codes
Warning code
Target function code
Condition
Basic function code
001/
201
Frequency upper limit setting (A061/A261)
>
Maximum frequency setting
(A004/A204/A304)
002/
202
Frequency lower limit setting (A062/A262)
>
005/
205/
305
Output frequency setting (F001) (*)
>
015/
215
Output frequency setting (F001) (*)
>
Frequency upper limit setting
(A061/A261)
019
Home search speed setting (P015)
>
025/
225
Output frequency setting (F001) (*)
<
Frequency lower limit setting
(A062/A262)
029
Home search speed setting (P015)
<
031/
231
Frequency upper limit setting (A061/A261)
<
Start frequency adjustment (b082)
032/
232
Frequency lower limit setting (A062/A262)
<
035/
235/
335
Output frequency setting (F001) (*)
<
037
Jog frequency setting (A038)
<
085/
285/
385
Output frequency setting (F001) (*)
< >
Jump (center) frequency settings
1/2/3 ± " Jump (hysteresis) frequency
width settings 1/2/3"
A063 ± A064, A065 ± A066,
A067 ± A068
086
Multispeed 1 to 15 settings (A021 to A035)
< >
091/
291
Frequency upper limit setting (A061/A261)
＞
Free-setting V/f frequency (7) (b112)
092/
292
Frequency lower limit setting (A062/A262)
＞
095/
295
Output frequency setting (F001) (*)
＞
5.2 Warning Codes
The following table lists the warning codes and the contents of parameter readjustments:
- The inverter displays a warning code when the data set as a target function code satisfies the condition (specified in the
Condition column) in relation to the data set as the corresponding basic function code.
- When the inverter is warning, it can not run to work the motor. Refer to the above column and modify the patramerters to the
correct data.
- When the inverter is warning, you can confirm the warning information ‘d090’.
* These parameters are checked, even when the digital operator (02) is not specified for the frequency source setting (A001).
5 - 5
Chapter 5 Error Codes
(Memo)
5 - 6
Chapter 6 Specifications
This chapter describes the specifications and external dimensions of the inverter.
6.1 Specifications ............................................... 6 - 2
6.2 External dimensions ..................................... 6 - 5
Chapter 6 Specifications
Model name (type name)
SJ700D-***LFF3/FUF3
004
007
015
022
037
055
075
110
150
185
220
300
370
450
550
Max. applicable motor
capacity (4-pole) (kW)
CT
0.4
0.75
1.5
2.2
3.7
5.5
7.5
11
15
18.5
22
30
37
45
55
VT
0.75
1.1
2.2
3.0
5.5
7.5
11
15
18.5
22
30
37
45
55
75
Rated capacity
(kVA)
200V
CT
1.0
1.7
2.5
3.6
5.7
8.3
11.0
15.9
22.1
26.3
32.9
41.9
50.2
63.0
76.2
VT
1.2
2.1
3.2
4.1
6.7
10.3
15.2
20.0
25.2
29.4
39.1
48.4
58.5
72.7
93.5
240V
CT
1.2
2.0
3.1
4.3
6.8
9.9
13.3
19.1
26.6
31.5
39.4
50.2
60.2
75.6
91.4
VT
1.5
2.6
3.9
4.9
8.1
12.4
18.2
24.1
30.3
35.3
46.9
58.1
70.2
87.2
112.2
Rated input AC voltage
Three-phase (3-wire), 200 to 240 V (+10%, -15%), 50/60 Hz (±5%)
Rated output voltage
Three-phase (3-wire), 200 to 240 V (corresponding to the input voltage)
Rated output current
(A)
CT
3.0
5.0
7.5
10.5
16.5
24
32
46
64
76
95
121
145
182
220
VT
3.7
6.3
9.4
12
19.6
30
44
58
73
85
113
140
169
210
270
Braking
Regenerative braking
Internal BRD circuit (external discharge resistor)
External regenerative
braking unit
Minimum connectable
resistance ()
50
50
35
35
35
16
10
10
7.5
7.5
5
-
Approx. weight (kg)
3.5
3.5
3.5
3.5
3.5 6 6 6 14
14
14
22
30
30
43
Model name (type name)
SJ700D-****FF3/FEF3/FUF3
007
015
022
037
040
055
075
110
150
185
220
300
370
450
550
750
900
1100
1320
1500
Max. applicable
motor capacity
(4-pole) (kW)
CT
0.75
1.5
2.2
3.7/
4.0
5.5
7.5
11
15
18.5
22
30
37
45
55
75
90
110
132/
150
VT
1.5
2.2
3.7
5.5
7.5
11
15
18.5
22
30
37
45
55
75
90
110
132
160
Rated
capacity
(kVA)
400V
CT
1.7
2.6
3.6
6.2
9.7
13.1
17.3
22.1
26.3
33.2
40.1
51.9
62.3
76.2
103.2
121.9
150.3
180.1
VT
2.1
3.3
4.6
7.6
11.0
15.2
20.0
25.6
29.7
39.4
48.4
58.8
72.7
93.5
110.8
135
159.3
200.9
480V
CT
2.0
3.1
4.3
7.4
11.6
15.8
20.7
26.6
31.5
39.9
48.2
62.3
74.8
91.4
123.8
146.3
180.4
216.1
VT
2.5
3.9
5.5
9.2
13.3
18.2
24.1
30.7
35.7
47.3
58.1
70.6
87.2
112.2
133
162.1
191.2
241.1
Rated input AC voltage
Three-phase (3-wire), 380 to 480 V (+10%, -15%), 50/60 Hz (±5%)
Rated output voltage
Three-phase (3-wire), 380 to 480 V (corresponding to the input voltage)
Rated output
current (A)
CT
2.5
3.8
5.3
9.0
14
19
25
32
38
48
58
75
91
112
149
176
217
260
VT
3.1
4.8
6.7
11.1
16
22
29
37
43
57
70
85
105
135
160
195
230
290
Braking
Regenerative braking
Internal BRD circuit
(external discharge resistor)
External regenerative braking unit
Minimum connectable
resistance ()
100
100
100
70
70
35
35
24
24
20
-
Approx. weight (kg)
3.5
3.5
3.5
3.5 6 6 6 14
14
14
22
30
30
30
55
55
70
70
Model name (type name)
SJ700D-****FF3/FEF3/FUF3
004 L 007
L/H
015
L/H
022
L/H
037
040
L/H
055
L/H
075
L/H
110
L/H
150
L/H
185
L/H
220
L/H
300
L/H
370
L/H
450
L/H
550
L/H
750
L/H
900 H 1100
H
1320
1500
H
Protective structure
IP20
IP00
Control system
Sine-wave PWM control
Output frequency range
0.1 to 400 Hz (Note 3)
Frequency accuracy
Within ±0.01% of the maximum output frequency for digital input,
within ±0.2% of maximum frequency for digital input (at 25±10C)
Frequency setting
resolution
Digital input: 0.01 Hz
Analog input: Maximum output frequency/4000
(O terminal input: 12 bits/0 to +10 V, O2 terminal input: 12 bits/-10 to +10 V,
OI terminal input: 12 bits/0 to +20 mA)
Voltage/frequency
characteristic
IM : V/f characteristic variable with the base frequency set between 30 to 400 Hz,
constant- or reduced-torque V/f control, SLV : sensorless vector control,
0Hz-SLV : 0Hz ranged sensorless vector control (only CT), vector with sensor (only CT)
Speed fluctuation
±0.5% (with sensorless vector control) Note8)
Rated overload current
CT : 150%/60sec, 200%/3sec
VT : 120％/60sec, 150%/5sec
CT：150%/60sec,
180％/3sec
VT：120％/60sec,
150%/5sec
Acceleration/deceleration
time
0.01 to 3,600.0 seconds (in linear or curved pattern)
Starting
torque
SLV
CT : 200%/0.3Hz
VT : 150％/0.5Hz
CT : 180%/0.3Hz
VT : 120%/0.5Hz
0Hz-SLV
CT : 150%/0Hz range (with motor less one power level than inverter)
VT : Disable.
CT : 130% (same as the left)
VT : Disable.
6.1 Specifications (CT : Constant torque mode, VT : Variable torque mode)
(1) Specifications of the 200 V class model
(2) Specifications of the 400 V class model
(3) Common specifications of 200 V class and 400 V class models
note) There are only 037HFF3, 037HFUF3 and 040HFEF3 as 037/040 model.
note) There are only 1320HFF3, 1320HFEF3 and 1500HFUF3 as 1320/1500 model.
6 - 2
Chapter 6 Specifications
Model name (type name)
SJ700D-****FF3/FEF3/FUF3
004 L 007
L/H
015
L/H
022
L/H
037
040
L/H
055
L/H
075
L/H
110
L/H
150
L/H
185
L/H
220
L/H
300
L/H
370
L/H
450
L/H
550
L/H
750 H 900 H 1100
H
1320
1500
H
Input
Frequency
setting
Standard
operator
Setting with
2
1
and2 keys
External
signal
(Note6)
0 to +10 VDC, -10 to +10 VDC (input impedance: 10k), 4 to 20 mA (input impedance: 100)
External
port
Setting via RS485 communication
Start/stop command
Forward/reverse command
Standard
operator
Start/stop commands (forward/reverse switching by parameter setting)
External
signal
Forward-operation start/stop commands (reverse-operation start/stop possible when relevant commands are assigned to
intelligent input terminals)
3-wire input possible (when relevant commands are assigned to control circuit terminals)
External
port
Setting via RS485 communication
Intelligent input
terminals
8 terminals, NO/NC switchable, sink logic/source logic switchable
[Terminal functions] Select eight of 69 functions.
Reverse operation (RV), Multispeed 1 setting (CF1), Multispeed 2 setting (CF2), Multispeed 3 setting (CF3), Multispeed 4
setting (CF4), Jogging (JG), external DC braking (DB), 2nd motor control (SET), 2-stage acceleration/deceleration (2CH),
free-run stop (FRS), external trip (EXT), unattended start protection (USP), commercial power supply switching (CS),
software lock (SFT), analog input switching (AT), 3rd motor control (SET3), reset (RS), starting by 3-wire input (STA),
stopping by 3-wire input (STP), forward/reverse switching by 3-wire input (F/R), PID disable (PID), PID integration reset
(PIDC), control gain switching (CAS), acceleration by remote control (UP), deceleration by remote control (DWN), data
clearance by remote control (UDC), forcible operation (OPE), multispeed bit 1 (SF1), multispeed bit 2 (SF2), multispeed
bit 3 (SF3), multispeed bit 4 (SF4), multispeed bit 5 (SF5), multispeed bit 6 (SF6), multispeed bit 7 (SF7), overload
restriction selection (OLR), torque limit selection (enabling/disabling) (TL), torque limit 1 (TRQ1), torque limit 2 (TRQ2),
P/PI switching (PPI), LAD cancellation (LAC), trigger for frequency addition (A145) (ADD), forcible-terminal
operation (F-TM), cumulative power clearance (KHC), general-purpose input 1 (MI1), general-purpose input 2 (MI2),
general-purpose input 3 (MI3), general-purpose input 4 (MI4), general-purpose input 5 (MI5), general-purpose input 6
(MI6), general-purpose input 7 (MI7), general-purpose input 8 (MI8), analog command holding (AHD), emergency
stop(EMR)*Note4,no assignment (no)
Thermistor input
terminal
1 terminal (positive temperature coefficient/negative temperature coefficient switchable for resistor)
Output
Intelligent
output terminals
5 open-collector output terminals, NO/NC switchable, sink logic/source logic switchable
1 relay (1c-contact) output terminal: NO/NC switchable
[Terminal functions] Select six of 51 functions.
Running (RUN), constant-speed reached (FA1), set frequency overreached (FA2), overload notice advance signal (1)
(OL), output deviation for PID control (OD), alarm signal (AL), set frequency reached (FA3), over-torque (OTQ),
instantaneous power failure (IP), under voltage (UV), torque limited (TRQ), operation time over (RNT), plug-in time
over (ONT), thermal alarm signal (THM), 0 Hz detection signal (ZS), set frequency overreached 2 (FA4), set frequency
reached 2 (FA5), overload notice advance signal (2) (OL2), PID feedback comparison (FBV), communication line
disconnection (NDc), logical operation result 1 (LOG1), logical operation result 2 (LOG2), logical operation result 3
(LOG3), logical operation result 4 (LOG4), logical operation result 5 (LOG5), logical operation result 6 (LOG6),
capacitor life warning (WAC), cooling-fan speed drop (WAF), starting contact signal (FR), heat sink overheat warning
(OHF), low-current indication signal (LOC), general-purpose output 1 (M01), general-purpose output 2 (M02),
general-purpose output 3 (M03), general-purpose output 4 (M04), general-purpose output 5 (M05), general-purpose
output 6 (M06), inverter ready (IRDY), forward rotation (FWR), reverse rotation (RVR), major failure (MJA), alarm code
0 to 3 (AC0 to AC3)
Intelligent
monitor output
terminals
Analog voltage output(Note7), analog current output(Note7), pulse-string output
(e.g., A-F, D-F [n-fold, pulse output only], A, T, V, P)
Monitoring on
display
Output frequency, output current, output torque, frequency conversion data, trip history,
input/output terminal status, electric power, and others
DC braking
Triggered at motor start-up, when the actual motor frequency exceeds the acceleration frequency set by a stop
command, when the actual motor frequency exceeds the frequency set by a frequency command,
or by an externally input command (braking force, time, and frequency are variable).
Other functions
Free V/f setting (7 breakpoints), frequency upper/lower limit, jump (center) frequency, acceleration/deceleration
according to characteristic curve, manual torque boost level/breakpoint, energy-saving operation, analog meter
adjustment, start frequency setting, carrier frequency adjustment, electronic thermal function (available also for free
setting), external start/end frequency/frequency rate, analog input selection, retry after trip, restart after instantaneous
power failure, output of various signals, starting with reduced voltage, overload restriction, initial-value setting, automatic
deceleration at power failure, AVR function, fuzzy acceleration/deceleration, online/offline auto-tuning, high-torque
multi-motor operation (sensorless vector control of two motors by one inverter)
Carrier frequency
variation
CT : 0.5 to 15kHz
VT : 0.5 to 12 kHz
CT : 0.5 to 10kHz
VT : 0.5 to 8 kHz
Protective functions
Overcurrent protection, overvoltage protection, under voltage protection, electronic thermal protection, temperature error
protection, instantaneous power failure protection, phase loss input protection, braking-resistor overload protection,
ground-fault current detection at power-on, USP error, external trip, emergency stop trip, CT error, communication error,
option board error, and others
(3) Common specifications of 200 V class and 400 V class models (continued)
6 - 3
Chapter 6 Specifications
Model name (type name)
SJ700D-****FF3/FEF3/FUF3
004 L 007
L/H
015
L/H
022
L/H
037
040
L/H
055
L/H
075
L/H
110
L/H
150
L/H
185
L/H
220
L/H
300
L/H
370
L/H
450
L/H
550
L/H
750 H 900 H 1100
H
1320
1500
H
Operating
environment
Ambient temperature,
storage
temperature(Note5),
humidity
-10C to +50C (ambient), -20C to +65C (storage), 20% to 90% RH (no condensation allowed)
Vibration tolerance
(See Note 1.)
5.9m/s2 (0.6G),10～55Hz
2.94m/s2 (0.3G),10～55Hz
Installation
environment
Environment without corrosive gases and dust, at an altitude of 1,000 m or less Note9)
Coating color
Grey
Optional
boards
Feedback option
Vector control with sensor
Digital input option
4-digit BCD input, 16-bit binary input
DeviceNet option
Option to support the open-network DeviceNet function (Same as SJ700-2) note12)
Profibus-DP option
Option to support the open-network Profibus-DP function (Same as SJ700-2) note12)
Other optional components
LCD operator WOP, digital operator with potentiometer,
Braking resistor, AC reactor, DC reactor, Noise filter, Operator cables, Harmonic-wave suppressor unit,
LCR filter, Analog operation panel, Regenerative braking unit, Regenerative energy-saving unit,
Harmonics suppression unit, Controllers for various applications, PC tool ProdriveNext
(3) Common specifications of 200 V class and 400 V class models (continued)
Note 1: The vibration tolerance was tested in compliance with JIS C60068-2-6:2010 (IEC 60068-2-6:2007).
Note 2: The insulation distance complies with the UL and CE standards.
Note 3: The applicable motor refers to Hitachi standard 3-phase motor(4-pole).when using other motors, care must be taken to prevent the rated
motor current(50/60Hz)from exceeding the rated output current of the inverter.
Note 4: Function “64(EMR)”cannot be assigned to input terminal 3 by an operation from the operator. The function is automatically assigned to
the terminal when slide switch SW1 is set to ON.
Note 5: The storage temperature refers to the short-term temperature during transport.
Note 6: The frequency command will equal the maximum frequency at 9.8V for input voltage 0 to 10VDC, or at 19.6mA for input current 4 to
20mA.If this characteristic is not satisfactory for your application, contact your Hitachi sales representative.
Note 7: The analog voltage monitor and the analog current monitor are rough output values for analog meter connection.
The maximum output value might shift a little by the difference of the analog output circuit than 10V or 20mA.
Please inquire when there is a possibility that the inconvenience is caused.
Note8: As for the range of the speed change, the variation range is different according to the installation situation and the characteristic and the
usage condition of the motor. Please inquire about details.
Note9: The density of air decreases by 1% whenever rising by 100m when the altitude exceeds 1000m. Therefore, it is necessary to decrease the
calorific value. The calorific value of the main circuit semiconductor such as IGBT is proportional to the current and the voltage.
Therefore, please decrease by 1% and use the current rating every time it rises by 100m.
Please inquire about use in the high ground of 2500m or more.
Note10: When Sensor-less vector control is selected (A044=03), you may not obtain an intended starting torque or motor may trip depending on
the applied motor.
Note11: The inverter detects IGBT error (E30) as a protection function.
However IGBT error (E30) is not a protection for an output short circuit, therefore there is a possibility that IGBT will get damaged.
Moreover overcurrent error (E01 to E04) may be detected instead of IGBT error depending on the operational condition of an inverter.
Note12: The option cannot access new parameters in SJ700D-3.
6 - 4
Chapter 6 Specifications
6.2 External dimensions
（200V class）SJ700D-004 to 037 LFF3/LFEF3/LFUF3
（400V class）SJ700D-007 to 037 HFF3/HFEF3/HFUF3
SJ700D-055 to 110 LFF3/LFEF3/LFUF3/HFF3/HFEF3/HFUF3
6 - 5
Chapter 6 Specifications
SJ700D-150 to 220 LFF3/LFEF3/LFUF3/HFF3/HFEF3/HFUF3
SJ700D-300 LFF3/LFEF3/LFUF3/HFF3/HFEF3/HFUF3
6 - 6
Chapter 6 Specifications
SJ700D-370 to 450 LFF3/LFEF3/LFUF3/HFF3/HFEF3/HFUF3
SJ700D-550HFF3/HFEF3/HFUF3
SJ700D-550LFF3/LFEF3/LFUF3
6 - 7
Chapter 6 Specifications
SJ700D-750 to 900 HFF3/HFEF3/HFUF3
SJ700D-1100HFF3/HFEF3/HFUF3，SJ700D-1320HFF3/HFEF3，SJ700D-1500HFUF3
6 - 8
Loading...