Hitachi SJ700-2 SERIES Service Manual

HITACHI INVERTER

SJ700-2 SERIES

SERVICE MANUAL

After reading this manual, keep it handy for future reference.

NTS204X

Revision History

No. Revision content Date of issue Manual code

1 First edition Octover 2007 NTS204X

- The current edition of this Instruction Manual also includes some corrections of simple misprints, missing letters, misdescriptions and certain added explanations other than those listed in the above Revision History table.

Table of contents

Chapter 1 Investigation of the inverter

1.1 Spesification label(Model name,manufacturing number:MFG) ················································1 - 1

1.1.1 Model name, ················································································································1 - 1

1.1.2 MFG number················································································································1 - 1

1.2 Precautions for Data Setting·····································································································1 - 2

1.2.1 Monitor Mode···············································································································1 - 2

1.2.2 Function Mode·············································································································1 - 3

1.2.3 Extended Function Mode ····························································································1 - 4

1.3 Code display system and key operations ·················································································1 - 20

1.3.1 Example of operation in basic display mode(“b037”=”04”[factory setting])·················1 - 21

1.3.2 Example of operation in full display mode(“b037”=”00”[factory setting])·····················1 - 23

1.3.3 Code/data display and key operator in extended function mode U ····························1 - 24

Chapter 2 Troubleshooting

2.1 Inverter trip contents,remedy,advise·························································································2 - 1

2.2 Option board error codes··········································································································2 - 5

2.2.1 Error indications by protective functions with the feedback option board (SJ-FB) mounted

·································································································································2 - 5

2.2.2 Error indications by protective functions with the digital option board (SJ-DG) mounted

·································································································································2 - 6

2.2.3 Error indications by protective functions with the DeviceNet option board (SJ-DN) mounted

·································································································································2 - 7

2.2.4 Error indications by protective functions with the easy sequence function used········2 - 8

2.3 Trip conditions monitoring········································································································2 - 9

2.4 Warning Codes·························································································································2 -10

2.5

Initialization setting················································································································2 -11

Chapter 3 Debug Mode

3.1 Monitor Modes ··························································································································3 - 1

3.2 Function Modes ························································································································3 - 2

3.3 How To Reference the Data Area (d105) Corresponding to Trip History··································3 - 2

3.4 Inverter Setting ·························································································································3 - 3

3.4.1 Setting procedure ········································································································ 3 - 3

3.4.2 Confirming the completion of initialization···································································3 - 4

Chapter 4 The check of control power supply voltage and a control signal

4.1 Control power supply ················································································································4 - 1

4.2 Control signal····························································································································4 - 1

Chapter 5 Maintenance and Inspection

5.1 Precautions for Maintenance and Inspection ···········································································5 - 1

5.1.1 Daily inspection············································································································5 - 1

5.1.2 Cleaning·······················································································································5 - 1

5.1.3 Periodic inspection·······································································································5 - 1

5.2 Daily and Periodic Inspections·································································································5 - 2

5.3 Ground Resistance Test with a Megger···················································································5 - 3

5.4 Withstand Voltage Test·············································································································5 - 3

5.5 Method of Checking the Inverter and Converter Circuits························································· 5 - 4

5.6 Replacing Parts························································································································5 - 5

5.7 Inverter Replacement···············································································································5 - 8

iii

Appendix

Circuit Diagram····························································································································6 - 1 Internal block diagram ·················································································································6 - 2 Structure figure····························································································································6 - 15

iv

1. Investigation of the inverter

1.1 Specification label(Model name,Manufacturing number:MFG)

･There is a specification label attached to the inverter as shown in Figure 1-1.

Figure 1-1 Location of the specifications label

･Please confirm the model name and MFG number from the specification label as follows.

Maximum applicable motor capacity

Inverter model

Input ratings

Output ratings Serial number

Model: SJ700-150HFF2

kW/(HP): 15/(20)

Input/Entree: 50Hz,60Hz V 1 Ph A

50Hz,60Hz 380-480V 3 Ph 35A

Output/Sortie: 0 -400Hz 380-480V 3 Ph 32A

MFGNo. 77AAT12345 A 001 Date: 0707

Hitachi Industrial Equipment

Systems Co.,Ltd.

Figure 1-2 Contents of the specifications label

1.1.1 Model name

SJ700-150 H F F 2

2:type2

F:with EMC filter F:with digital operator L:3Ø200V class H:3Ø400V class Applicable motor(150:15kW)

Model name

1.1.2 MFG number

77 A T12345 7 001

Serial No.(001-999) Year of production(7:2007 Production No. REV.No.(1 charactor or 2 character)

Production year & month(78:2007/August)

Specification label

MADE IN JAPAN

)

NE

1 - 1

1.2 Precautions for Data Setting

The default display mode limits the screens (parameters) that can be displayed on the monitor. To enable the display of all parameters, specify "00" (full display) for the function code display restriction (b037). To enable the parameters to be changed while the inverter is operating, specify "10" for the software lock mode selection (b031).

1.2.1 Monitoring Mode

Code Function name Monitored data or setting Default d001 Output frequency monitoring 0.00 to 99.99, 100.0 to 400.0 (Hz) d002 Output current monitoring 0.0 to 999.9, 1000 to 9999 (A) d003 Rotation direction minitoring F (forward rotation), o (stopped), r (reverse rotation) d004 Process variable (PV), PID feedback

monitoring

d005 Intelligent input terminal status (Example)

d006 Intelligent output terminal status (Example)

0.00 to 99.99, 100.0 to 999.9, 1000. to 9999. 1000 to 9999 (10000 to 99990), 100 to 999 (100000 to 999000)

8 7

FW

5

4

3 2 1

6

Terminals FW, 7, 2, and 1: ON Terminals 8, 6, 5, 4, and 3: OFF

Terminals 12 and 11: ON Terminals AL, 15, 14, and 13: OFF

AL 15 14 13 12 11

d007 Scaled output frequency monitoring 0.00 to 99.99, 100.0 to 999.9, 1000. to 9999., 1000 to 3996 (10000 to 39960) d008 Actual-frequency monitoring -400. to -100., -99.9 to 0.00 to 99.99, 100.0 to 400.0 (Hz) d009 Torque command monitoring -200. to +200. (%) d010 Torque bias monitoring -200. to +200. (%) d012 Torque monitoring -200. to +200. (%) d013 Output voltage monitoring 0.0 to 600.0 (V) d014 Power monitoring 0.0 to 999.9 (kW) d015 Cumulative power monitoring 0.0 to 999.9, 1000. to 9999.

d016 Cumulative operation RUN time

monitoring d017 Cumulative power-on time monitoring d018 Heat sink temperature monitoring d019 Motor temperature monitoring d022 Life-check monitoring 1: Capacitor on main circuit board

d023 Program counter 0 to 1024 d024 Program number monitoring 0000 to 9999

1000 to 9999 (10000 to 99990), 100 to 999 (100000 to 999000)

0. to 9999., 1000 to 9999 (10000 to 99990), 100 to 999 (100000 to 999000) (hr)

0. to 9999., 1000 to 9999 (10000 to 99990), 100 to 999 (100000 to 999000) (hr) 

-020. to 200.0 (C) 

2: Cooling-fan speed drop

ON OFF

2 1

Note

  



      



 

1 - 2

Code Function name Monitored data or setting Default Note

d025 User monitor 0 -2147483647 to 2147483647 (upper 4 digits including “-“)

d026 User monitor 1 -2147483647 to 2147483647 (upper 4 digits including “-“)

d027 User monitor 2 -2147483647 to 2147483647 (upper 4 digits including “-“)

d028 Pulse counter 0 to 2147483647 (upper 4 digits)

d029 Position setting monitor -1073741823 to 1073741823 (upper 4 digits including “-“)

d030 Position feedback monitor -1073741823 to 1073741823 (upper 4 digits including “-“)

d080 Trip Counter 0. to 9999., 1000 to 6553 (10000 to 65530) (times)

Trip monitoring 1 Factor, frequency (Hz), current (A), voltage across P-N (V), running time (hours),

d081

Trip monitoring 2 Factor, frequency (Hz), current (A), voltage across P-N (V), running time (hours),

d082

Trip monitoring 3 Factor, frequency (Hz), current (A), voltage across P-N (V), running time (hours),

d083

Trip monitoring 4 Factor, frequency (Hz), current (A), voltage across P-N (V), running time (hours),

d084

Trip monitoring 5 Factor, frequency (Hz), current (A), voltage across P-N (V), running time (hours),

d085

Trip monitoring 6 Factor, frequency (Hz), current (A), voltage across P-N (V), running time (hours),

d086

d090 Programming error monitoring Warning code

d102 DC voltage monitoring 0.0 to 999.9 (V)

d103 BRD load factor monitoring 0.0 to 100.0 (%)

d104 Electronic thermal overload monitoring 0.0 to 100.0 (%)

power-on time (hours)

−

1.2.2 Function Mode

Code Function name Monitored data or setting

Output frequency setting 0.0, "start frequency" to "maximum frequency" (or maximum frequency,

F001

F002 Acceleration (1) time setting 0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s) 30.00

F202 Acceleration (1) time setting, 2nd

motor

F302 Acceleration (1) time setting, 3rd

motor

F003 Deceleration (1) time setting 0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s) 30.00

F203 Deceleration time setting, 2nd motor 0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s) 30.00

F303 Deceleration time setting, 3rd motor 0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s) 30.00

F004 Keypad Run key routing 00 (forward rotation), 01 (reverse rotation) 00

2nd/3rd motors) (Hz)

0.0 to 100.0 (when PID function is enabled)

0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s) 30.00

Default

_FF _FEF _FUF

0.00

1 - 3

1.2.3 Extended Function Mode

Code Funct ion name Monitored data or setting

Frequency source setting 00 (keypad potentiometer) (*1), 01 (control circuit terminal block), 02 (digital

A001

Run command source setting 01 (control circuit terminal block), 02 (digital operator), 03 (RS485), 04 (option

A002

A003 Base frequency setting 30. to "maximum frequency " (Hz) 60. 50. 60.

Base frequency setting, 2nd

A203

motor

Base frequency setting, 3rd

A303

Basic settings

Analog input and others

Multispeed operation and jogging

.

motor

A004 Maximum frequency setting 30. to 400. (Hz) 60. 50. 60.

Maximum frequency setting, 2nd

A204

motor

Maximum frequency setting, 3rd

A304

motor

[AT] selection 00 (switching between O and OI terminals), 01 (switching between O and O2

A005

[O2] selection 00 (single), 01 (auxiliary frequency input via O and OI terminals)

A006

[O]-[L] input active range start

A011

frequency

[O]-[L] input active range end

A012

frequency

[O]-[L] input active range start

A013

voltage

[O]-[L] input active range end

A014

voltage

[O]-[L] input active range start

A015

frequency selection

External frequency filter time

A016

const.

Easy sequence function

A017

selection

Multispeed operation selection 00 (binary: 16 speeds selectable with 4 terminals), 01 (bit: 8 speeds selectable

A019

A020 Multispeed frequency setting 0.0 or “start frequency” to “maximum frequency” (Hz) 0. 00

Multispeed frequency setting,

A220

2nd motor

Multispeed frequency setting,

A320

3rd motor

A021 Multispeed 1 setting 0.0 or “start frequency” to “1st maximum frequency” (Hz) 0.00

A022 Multispeed 2 setting 0.0 or “start frequency” to “2nd maximum frequency” (Hz) 0.00

A023 Multispeed 3 setting 0.0 or “start frequency” to “3rd maximum frequency” (Hz) 0.00

A024 Multispeed 4 setting 0.0 or “start frequency” to “n-th maximum frequency” (Hz) 0.00

A025 Multispeed 5 setting 0.0 or “start frequency” to “n-th maximum frequency” (Hz) 0.00

A026 Multispeed 6 setting 0.0 or “start frequency” to “n-th maximum frequency” (Hz) 0.00

A027 Multispeed 7 setting 0.0 or “start frequency” to “n-th maximum frequency” (Hz) 0.00

A028 Multispeed 8 setting 0.0 or “start frequency” to “n-th maximum frequency” (Hz) 0.00

A029 Multispeed 9 setting 0.0 or “start frequency” to “n-th maximum frequency” (Hz) 0.00

A030 Multispeed 10 setting 0.0 or “start frequency” to “n-th maximum frequency” (Hz) 0.00

A031 Multispeed 11 setting 0.0 or “start frequency” to “n-th maximum frequency” (Hz) 0.00

A032 Multispeed 12 setting 0.0 or “start frequency” to “n-th maximum frequency” (Hz) 0.00

A033 Multispeed 13 setting 0.0 or “start frequency” to “n-th maximum frequency” (Hz) 0.00

A034 Multispeed 14 setting 0.0 or “start frequency” to “n-th maximum frequency” (Hz) 0.00

A035 Multispeed 15 setting 0.0 or “start frequency” to “n-th maximum frequency” (Hz) 0.00

A038 Jog frequency setting "Start frequency" to 9.99 (Hz) 1.00

A039 Jog stop mode

operator), 03 (RS485), 04 (option 1), 05 (option 2), 06 (pulse-string input), 07 (easy sequence), 10 (operation function result)

1), 05 (option 2)

30. to "maximum frequency, 2nd motor" (Hz)

30. to "maximum frequency, 3rd motor" (Hz)

30. to 400. (Hz)

terminals), 02 (switching between O terminal and keypad potentiometer) (*1), 03 (switching between OI terminal and keypad potentiometer) (*1), 04 (switching between O2 and keypad potentiometer) (*1)

(nonreversible), 02 (auxiliary frequency input via O and OI terminals) (reversible), 03 (disabling O2 terminal)

0.00 to 99.99, 100.0 to 400.0 (Hz)

0. to "[O]-[L] input active range end voltage" (%)

"[O]-[L] input active range start voltage" to 100. (%)

00 (external start frequency), 01 (0 Hz)

1. to 30. or 31. (500 ms filter ±0.1 Hz with hysteresis)

00 (disabling), 01 (enabling)

with 7 terminals)

0.0 or “start frequency” to “maximum frequency, 2nd motor” (Hz)

0.0 or “start frequency” to “maximum frequency, 3rd motor” (Hz)

00 (free-running after jogging stops [disabled during operation]), 01 (deceleration and stop after jogging stops [disabled during operation]), 02 (DC braking after jogging stops [disabled during operation]), 03 (free-running after jogging stops [enabled during operation]), 04 (deceleration and stop after jogging stops [enabled during operation]), 05 (DC braking after jogging stops [enabled during operation])

Default

_FF _FEF _FUF

02 01 01

60. 50. 60.

00

03

0.00

0.

100.

01

31.

00

0.00

00

Note

1 - 4

Code Function name Monitored data or setting

A041 Torque boost method selection 00 (manual torque boost), 01 (automatic torque boost) 00

Torque boost method selection,

A241

2nd motor

A042 Manual torque boost value 0.0 to 20.0 (%) 1.0

Manual torque boost value, 2nd

A242

motor

Manual torque boost value, 3rd

A342

motor

Manual torque boost frequency

A043

adjustment

Manual torque boost frequency

A243

adjustment, 2nd motor

Manual torque boost frequency

A343

adjustment, 3rd motor

V/F characteristic curve

A044

selection, 1st motor

V/F characteristic curve

A244

V/f characteristic

DC braking

Frequency upper/lower limit and jump frequency

PID control

selection, 2nd motor

V/F characteristic curve

A344

selection, 3rd motor

A045 V/f gain setting 20. to 100. (%) 100.

Voltage compensation gain

A046

setting for automatic torque boost. 1st motor

Voltage compensation gain

A246

setting for automatic torque boost, 2nd motor

Slippage compensation gain

A047

setting for automatic torque boost, 1st motor

Slippage compensation gain

A247

setting for automatic torque boost, 2nd motor

A051 DC braking enable 00 (disabling), 01 (enabling), 02 (set frequency only) 00

A052 DC braking frequency setting 0.00 to 99.99, 100.0 to 400.0 (Hz) 0.50

A053 DC braking wait time 0.0 to 5.0 (s) 0.0

DC braking force during

A054

deceleration

A055 DC braking time for deceleration 0.0 to 60.0 (s) 0.0

DC braking/edge or level

A056

detection for [DB] input

A057 DC braking force for starting 0. to 100.(%) 0.

A058 DC braking time for starting 0.0 to 60.0( s) 0.0

DC braking carrier frequency

A059

setting

A061 Frequency upper limit setting 0.00 or "1st minimum frequency limit" to "maximum frequency" (Hz) 0.00

Frequency upper limit setting,

A261

2nd motor

A062 Frequency lower limit setting

Frequency lower limit setting,

A262

2nd motor

Jump (center) frequency setting

A063

1

Jump (hystere sis) frequency

A064

width setting 1

Jump (center) frequency setting

A065

2

Jump (hystere sis) frequency

A066

width setting 2

Jump (center) frequency setting

A067

3

Jump (hystere sis) frequency

A068

width setting 3

Acceleration stop frequency

A069

setting

Acceleration stop time frequency

A070

setting

A071 PID Function Enable 00 (disabling), 01 (enabling), 02 (enabling inverted-data output) 00

A072 PID proportional gain 0.2 to 5.0 1.0

A073 PID integral time constant 0.0 to 999.9, 1000. to 3600. (s) 1.0

A074 PID derivative gain 0.00 to 99.99, 100.0 (s) 0.00

A075 PV scale conversion 0.01 to 99.99 1.00

A076 PV source setting

A077 Output of inverted PID deviation 00(OFF), 01 (ON) 00

A078 PID variation range 0.0 to 100.0 (%) 0.00

A079 PID feed forward selection 00 (disabled), 01 (O input), 02 (OI input), 03 (O2 input) 00

00 (manual torque boost), 01 (automatic torque boost) 00

0.0 to 20.0 (%) 1.0

0.0 to 50.0 (%) 5.0

00 (VC), 01 (VP), 02 (free V/f), 03 (sensorless vector control), 04 (0Hz-range sensorless vector), 05 (vector with sensor)

00 (VC), 01 (VP), 02 (free V/f), 03 (sensorless vector control), 04 (0Hz-range sensorless vector)

00(VC), 01(VP) 00

0. to 255. 100.

0. to 100. (%) 0.

00 (edge operation), 01 (level operation) 01

0.5 to 15.0(kHz) 5.0

0.00 or "2nd minimum frequency limit" to "maximum frequency, 2nd motor" (Hz) 0.00

0.00 or "start frequency" to "maximum frequency limit" (Hz)

0.00 or "start frequency" to "maximum frequency, 2nd motor limit" (Hz)

0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00

0.00 to 10.00 (Hz) 0.50

0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00

0.00 to 10.00 (Hz) 0.50

0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00

0.00 to 10.00 (Hz) 0.50

0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00

0.0 to 60.0 (s) 0.0

00 (input via OI), 01 (input via O), 02 (external communication), 03 (pulse-string frequency input), 10 (operation result output)

Default

_FF _FEF _FUF

00

0.00

00

Note

1 - 5

Code Function name Monitored data or setting

A081 AVR function select 00 (always on), 01 (always off), 02 (off during deceleration) 02 00 00

AVR

A082 AVR voltage select

A085 Operation mode selection 00 (normal operation), 01 (energy-saving operation), 02 (fuzzy operation) 00

A086 Energy saving mode tuning 0.1 to 100.0 50.0

A092 Acceleration (2) time setting 0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s) 15.00

Acceleration (2) time setting,

A292

2nd motor

Acceleration (2) time setting,

A392

3rd motor

A093 Deceleration (2) time setting 0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s) 15.00

Deceleration (2) time setting,

A293

2nd motor

Deceleration (2) time setting,

A393

3rd motor

Select method to switch to

A094

Acc2/Dec2 profile

Select method to switch to

A294

Acc2/Dec2, 2nd motor

Acc1 to Acc2 frequency

A095

transition point

Acc1 to Acc2 frequency

A295

transition point, 2nd motor

Dec1 to Dec2 frequency

A096

Operation mode and acceleration/deceleration function

External frequency adjustment

n and

deceleratio

Operation-target frequency

deceleration

Acceleration and

transition point

Dec1 to Dec2 frequency

A296

transition point, 2nd motor

A097 Acceleration curve selection 00 (linear), 01 (S curve), 02 (U curve), 03 (inverted-U curve), 04 (EL-S curve) 00

A098 Deceleration curve setting 00 (linear), 01 (S curve), 02 (U curve), 03 (inverted-U curve), 04 (EL-S curve) 00

[OI]-[L] input active range start

A101

frequency

[OI]-[L] input active range end

A102

frequency

[OI]-[L] input active range start

A103

current

[OI]-[L] input active range end

A104

current

[OI]-[L] input start frequency

A105

enable

[O2]-[L] input active range start

A111

frequency

[O2]-[L] input active range end

A112

frequency

[O2]-[L] input active range start

A113

voltage

[O2]-[L] input active range end

A114

voltage

Acceleration curve constants

A131

setting

Deceleration curve constants

A132

setting

Operation-target frequency

A141

selection 1

Operation-target frequency

A142

selection 2

A143 Operator selection

A145 Frequency to be added 0. 00 to 99.99, 100.0 to 400.0 (Hz) 0.00

Sign of the frequency to be

A146

added

EL-S-curve acceleration

A150

ratio 1

EL-S-curve acceleration

A151

ratio 2

EL-S-curve deceleration

A152

ratio 1

EL-S-curve deceleration

A153

ratio 2

200 V class: 200, 215, 220, 230, 240 (V) 400 V class: 380, 400, 415, 440, 460, 480 (V)

0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s) 15.00

00 (switching by 2CH terminal), 01 (switching by setting), 02 (switching only when rotation is reversed)

0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00

0. to "[OI]-[L] input active range end current" (%) 20.

"[OI]-[L] input active range start current" to 100. (%) 100.

00 (external start frequency), 01 (0 Hz) 00

-400. to -100., -99.9 to 0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00

-100. to 02 end-frequency rate (%) -100.

"02 start-frequency rate" to 100. (%) 100.

01 (smallest swelling) to 10 (largest swelling) 02

00 (digital operator), 01 (keypad potentiometer), 02 (input via O), 03 (input via OI), 04 (external communication), 05 (option 1), 06 (option 2), 07 (pulse-string frequency input)

00 (addition: A141 + A142), 01 (subtraction: A141 - A142), 02 (multiplication: A141 x A142)

00 (frequency command + A145), 01 (frequency command - A145) 00

0. to 50. (%) 25.

Default

Note

_FF _FEF _FUF

200/400 230/400 230/460

00

02

03

00

1 - 6

Code Function name Monitored data or setting

b001 Selection of restart mode

Allowable under-voltage power

b002

failure time

b003 Retry wait time before motor restart 0.3 to 100.0 (s) 1.0

Instantaneous power

b004

failure/under-voltage trip alarm enable

Number of restarts on power

b005

failure/under-voltage trip events

b006 Phase loss detection enable 00 (disabling), 01 (enabling) 00

b007 Restart frequency threshold 0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00

b008 Selection of retry after tripping

b009 Selection of retry after undervoltage 00 (16 times), 01 (unlimited) 00

Selection of retry count after

b010

Restart after instantaneous power failure or tripping

Electronic thermal function

Overload restriction and overcurrent restraint

Software

lock

overvoltage or overcurrent

b011 Retry wait time after tripping 0.3 to 100.0 (s) 1.0

Electronic thermal setting

b012

(calculated within the inverter from current output)

Electronic thermal setting

b212

(calculated within the inverter from current output), 2nd motor

Electronic thermal setting

b312

(calculated within the inverter from current output), 3rd motor

b013 Electronic thermal characteristic

Electronic thermal characteristic, 2nd

b213

motor

Electronic thermal characteristic, 3rd

b313

motor

Free setting, electronic thermal

b015

frequency (1)

Free setting, electronic thermal

b016

current (1)

Free setting, electronic thermal

b017

frequency (2)

Free setting, electronic thermal

b018

current (2)

Free setting, electronic thermal

b019

frequency (3)

Free setting, electronic thermal

b020

current (3)

b021 Overload restriction operation mode

b022 Overload restriction setting 0.20 x "rated current" to 1.00 x "rated current" (A)

Deceleration rate at overload

b023

restriction

Overload restriction operation mode

b024

(2)

b025 Overload restriction setting (2) 0.20 x "rated current" to 2.00 x "rated current" (A)

Deceleration rate at overload restriction

b026

(2)

b027 Overcurrent suppression enable 00 (disabling), 01 (enabling) 01

Active frequency matching, scan

b028

start frequency

Active frequency matching,

b029

scan-time constant

Active frequency matching, restart

b030

frequency select

b031 Software lock mode selection

00 (tripping), 01 (starting with 0 Hz), 02 (starting with matching frequency), 03 (tripping after deceleration and stopping with matching frequency), 04 (restarting with active matching frequency)

0.3 to 25.0 (s) 1.0

00 (disabling), 01 (enabling), 02 (disabling during stopping and decelerating to stop)

00 (16 times), 01 (unlimited) 00

00 (tripping), 01 (starting with 0 Hz), 02 (starting with matching frequency), 03 (tripping after deceleration and stopping with matching frequency), 04 (restarting with active matching frequency)

1 to 3 (times) 3

0.20 x "rated current" to 1.00 x "rated current" (A) Rated current of inverter

00 (reduced-torque characteristic), 01 (constant-torque characteristic), 02 (free setting)

0. to 400. (Hz) 0.

0.0 to rated current (A) 0.0

0. to 400. (Hz) 0.

0.0 to rated current (A) 0.0

0. to 400. (Hz) 0.

0.0 to rated current (A) 0.0

00 (disabling), 01 (enabling during acceleration and deceleration), 02 (enabling during constant speed), 03 (enabling during acceleration and deceleration (increasing the speed during regeneration))

0.10 to 30.00 (s) 1.00

00 (disabling), 01 (enabling during acceleration and deceleration), 02 (enabling during constant speed), 03 (enabling during acceleration and deceleration (increasing the speed during regeneration))

0.10 to 30.00 (s) 1.00

0.20 x "rated current" to 2.00 x "rated current" (A) Rated current of inverter

0.10 to 30.00 (s) 0.50

00 (frequency at the last shutoff), 01 (maximum frequency), 02 (set frequency)

00 (disabling change of data other than "b031" when SFT is on), 01 (disabling change of data other than "b031" and frequency settings when SFT is on), 02 (disabling change of data other than "b031"), 03 (disabling change of data other than "b031" and frequency settings), 10 (enabling data changes during operation)

Default

_FF _FEF _FUF

00

00 01 01

01

Rated current of inverter x

1.50

01

Rated current of inverter x

1.50

00

01

Note

1 - 7

Code Function name Monitored data or setting

b034 Run/power-on warning time 0. to 9999. (0 t o 99990), 1000 to 6553 (10000 to 655300) (hr) 0.

b035 Rotational direction restriction

b036 Reduced voltage start selection

b037 Function code display restriction

Others

b038 Initial-screen selection

Automatic us er-parameter

b039

setting function enable

b040 Torque limit selection

Torque limit (1) (forward-driving

b041

in 4-quadrant mode)

Torque limit (2)

b042

(reverse-regenerating in 4-quadrant mode)

Torque limit (3) (reverse-driving

b043

Torque limitation

failure

Non-stop operation at momentary power

Window comparator

in 4-quadrant mode)

Torque limit (4)

b044

(forward-regenerating in 4-quadrant mode)

b045 Torque limit LADSTOP enable 00 (disabling), 01 (enabling) 00

b046 Reverse Run protection enable 00 (disabling), 01 (enabling) 00

Controller deceleration and stop

b050

on power loss

DC bus voltage trigger level

b051

during power loss

Over-voltage threshold during

b052

power loss

Deceleration time setting during

b053

power loss

Initial output frequency decrease

b054

during power loss

Proportional gain setting for

b055

nonstop operation at power loss

Integral time setting for nonstop

b056

operation at power loss

Maximum-limit level of window

b060

comparators O

Minimum-limit level of window

b061

comparators O

Hysteresis width of window

b062

comparators O

Maximum-limit level of window

b063

comparators O I

Minimum-limit level of window

b064

comparators O I

Hysteresis width of window

b065

comparators O I

Maximum-limit level of window

b066

comparators O I

Minimum-limit level of window

b067

comparators O/OI/O2

Hysteresis width of window

b068

comparators O/OI/O2

Operation level at O

b070

disconnection

Operation level at OI

b071

disconnection

Operation level at O2

b072

disconnection

00 (enabling both forward and reverse rotations), 01 (enabling only forward rotation), 02 (enabling only reverse rotation)

0 (minimum reduced voltage start time) to 255 (maximum reduced voltage start time)

00 (full display), 01 (function-specific display), 02 (user setting), 03 (data comparison display), 04 (basic display)

00 (screen displayed when the STR key was pressed last), 01 (d001), 02 (d002), 03 (d003), 04 (d007), 05 (F001)

00 (disabling), 01 (enabling) 00

00 (quadrant-specific setting), 01 (switching by terminal), 02 (analog input), 03 (option 1), 04 (option 2)

0. to 200. (%), no (disabling torque limitation) 150.

00 (disabling), 01 (nonstop deceleration to stop), 02 (DC voltage constant control, with resume), 03 ( without resume)

0.0 to 999.9, 1000. (V) 220/440

0.0 to 999.9, 1000. (V) 360/720

0.01 to 99.99, 100.0 to 999.9, 1000. to 3600. (s) 1.00

0.00 to 10.00 (Hz) 0.00

0.00 to 2.55 0.20

0.000 to 9.999 /10.00 to 65.53 (s) 0.100

0. to 100. (lower limit : b061 + b062 / 2) (%) 100

0. to 100. (lower limit : b060 - b062 / 2) (%) 0

0. to 10. (lower limit : b061 - b062 / 2) (%) 0

0. to 100. (lower limit : b064 + b066 / 2) (%) 100

0. to 100. (lower limit : b063 - b066 / 2) (%) 0

0. to 10. (lower limit : b063 - b064 / 2) (%) 0

-100. to 100. (lower limit : b067 + b068 / 2) (%) 100

-100. to 100. (lower limit : b066 - b068 / 2) (%) 0

0. to 10. (lower limit : b066 - b067 / 2) (%) 0

0. to 100. (%) or "no" (ignore) no

-100. to 100. (%) or "no" (ignore) no

Default

_FF _FEF _FUF

00

6

04

01

00

Note

1 - 8

Code Function name Monitored data or setting

Cumulative input power data

b078

clearance

Cumulative input power display

b079

gain setting

b082 Start frequency adjustment 0.10 to 9.99 (Hz) 0.50

b083 Carrier frequency setting 0.5 to 15.0 (kHz) (subject to derating) 5.0

Initialization mode (parameters or

b084

trip history)

b085 Country code for initialization 00 (Japan), 01 (EU), 02 (U.S.A.) 00 01 02

Frequency scaling conversion

b086

factor

b087 STOP key enable 00 (enabling), 01 (disabling), 02 (disabling only the function to stop) 00

b088 Restart mode after FRS

Others

Free setting of V/f characteristic

Others

Automatic carrier frequency

b089

reduction

b090 Dynamic braking usage ratio 0.0 to 100.0 (%) 0.0

b091 Stop mode selection 00 (deceleration until stop), 01 (free-run stop) 00

b092 Cooling fan control

b095 Dynamic braking control

b096 Dynamic braking activation level 330 to 380, 660 to 760(V)

Thermistor for thermal protection

b098

control

b099 Thermal protection level setting

b100 Free-setting V/f frequency (1) 0. to "free-setting V/f frequency (2)" (Hz) 0.

b101 Free-setting V/f voltage (1) 0.0 to 800.0 (V) 0.0

b102 Free-setting V/f frequency (2) 0. to "free-setting V/f frequency (3)" (Hz) 0.

b103 Free-setting V/f voltage (2) 0.0 to 800.0 (V) 0.0

b104 Free-setting V/f frequency (3) 0. to "free-setting V/f frequency (4)" (Hz) 0.

b105 Free-setting V/f voltage (3) 0.0 to 800.0 (V) 0.0

b106 Free-setting V/f frequency (4) 0. to "free-setting V/f frequency (5)" (Hz) 0.

b107 Free-setting V/f voltage (4) 0.0 to 800.0 (V) 0.0

b108 Free-setting V/f frequency (5) 0. to "free-setting V/f frequency (6)" (Hz) 0.

b109 Free-setting V/f voltage (5) 0.0 to 800.0 (V) 0.0

b110 Free-setting V/f frequency (6) 0. to "free-setting V/f frequency (7)" (Hz) 0.

b111 Free-setting V/f voltage (6) 0.0 to 800.0 (V) 0.0

b112 Free-setting V/f frequency (7) 0. to 400. (Hz) 0.

b113 Free-setting V/f voltage (7) 0.0 to 800.0 (V) 0.0

b120 Brake Control Enable 00 (disabling), 01 (enabling) 00

b121 Brake Wait Time for Release 0.00 to 5.00 (s) 0.00

b122 Brake Wait Time for Acceleration 0.00 to 5.00 (s) 0.00

b123 Brake Wait Time for Stopping 0.00 to 5.00 (s) 0.00

b124 Brake Wait Time for Confirmation 0.00 to 5.00 (s) 0.00

b125 Brake Release Frequency Setting 0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00

b126 Brake Release Current Setting 0.0 to 2.00 x "rated current" Rated current of inverter

b127 Braking frequency 0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00

b130 Overvoltage suppression enable

b131 Overvoltage suppression level 330 to 390 (V) (200 V class model), 660 to 780 (V) (400 V class model)

Acceleration and deceleration

b132

rate at overvoltage suppression

Overvoltage suppression

b133

propotional gain

Overvoltage suppression Integral

b134

time

Clearance by setting "01" and pressing the STR key 00

1. to 1000. 1.

00 (clearing the trip history), 01 (initializing the data), 02 (clearing the trip history and initializing the data)

0.1 to 99.0 1.0

00 (starting with 0 Hz), 01 (starting with matching frequency), 02 (starting with active matching frequency)

00: invalid, 01: valid 00

00 (always operating the fan), 01 (operating the fan only during inverter operation [including 5 minutes after power-on and power-off])

00 (disabling), 01 (enabling [disabling while the motor is topped]), 02 (enabling [enabling also while the motor is topped])

00 (disabling the thermistor), 01 (enabling the thermistor with PTC), 02 (enabling the thermistor with NTC)

0. to 9999. (Ω)

00 (disabling the restraint), 01 (controlled deceleration), 02 (enabling acceleration)

0.10 to 30.00 (s) 1.00

0.00 to 2.55 0.50

0.000 to 9.999 / 10.00 to 65.53 (s) 0.060

Default

_FF _FEF _FUF

00

360/

720

00

3000.

00

380/

760

Note

1 - 9

Code Function name Monitored data or setting

C001 Terminal [1] function (*2)

C002 Terminal [2] function 16

C003 Terminal [3] function (*2)

C004 Terminal [4] function 11

C005 Terminal [5] function 09

C006 Terminal [6] function 03 03 13

C007 Terminal [7] function 02

C008 Terminal [8] function

Intelligent input terminals

C011 Terminal [1] active state 00 (NO) / 01 (NC) 00

C012 Terminal [2] active state 00 (NO) / 01 (NC) 00

C013 Terminal [3] active state 00 (NO) / 01 (NC) 00

C014 Terminal [4] active state 00 (NO) / 01 (NC) 00

C015 Terminal [5] active state 00 (NO) / 01 (NC) 00

C016 Terminal [6] active state 00 (NO) / 01 (NC) 00

C017 Terminal [7] active state 00 (NO) / 01 (NC) 00

C018 Terminal [8] active state 00 (NO) / 01 (NC) 00

C019 Terminal [FW] active state 00 (NO) / 01 (NC) 00

01 (RV: Reverse RUN), 02 (CF1: Multispeed 1 setting), 03 (CF2: Multispeed 2 setting), 04 (CF3: Multispeed 3 setting), 05 (CF4: Multispeed 4 setting), 06 (JG: Jogging), 07 (DB: external DC braking), 08 (SET: Set 2nd motor data), 09 (2CH: 2-stage acceleration/deceleration), 11 (FRS: free-run stop), 12 (EXT: external trip), 13 (USP: unattended start protection), 14: (CS: commercial power source enable), 15 (SFT: software lock), 16 (AT: analog input voltage/current select), 17 (SET3: 3rd motor control), 18 (RS: reset), 20 (STA: starting by 3-wire input), 21 (STP: stopping by 3-wire input), 22 (F/R: forward/reverse switching by 3-wire input), 23 (PID: PID disable), 24 (PIDC: PID reset), 26 (CAS: control gain setting), 27 (UP: remote control UP function), 28 (DWN: remote control DOWN function), 29 ( DWN: remote control data clearing), 31 (OPE: forcible operation), 32 (SF1: multispeed bit 1), 33 (SF2: multispeed bit 2), 34 (SF3: multispeed bit 3), 35 (SF4: multispeed bit 4), 36 (SF5: multispeed bit 5), 37 (SF6: multispeed bit 6), 38 (SF7: multispeed bit 7), 39 (OLR: overload restriction selection), 40 (TL: torque limit enable), 41 (TRQ1: torque limit selection bit 1), 42 (TRQ2: torque limit selection bit 2), 43 (PPI: P/PI mode selection), 44 (BOK: braking confirmation), 45 (ORT: orientation), 46 (LAC: LAD cancellation), 47 (PCLR: clearance of position deviation), 48 (STAT: pulse train position command input enable), 50 (ADD: trigger for frequency addition [A145]), 51 (F-TM: forcible-terminal operation), 52 (ATR: permission of torque command input), 53 (KHC: cumulative power clearance), 54 (SON: servo-on), 55 (FOC: forcing), 56 (MI1: general-purpose input 1), 57 (MI2: general-purpose input 2), 58 (MI3: general-purpose input 3), 59 (MI4: general-purpose input 4), 60 (MI5: general-purpose input 5), 61 (MI6: general-purpose input 6), 62 (MI7: general-purpose input 7), 63 (MI8: general-purpose input 8), 65 (AHD: analog command holding), 66 (CP1: multistage position settings selection 1 ), 67 (CP2: multistage position settings selection 2), 68 (CP3: multistage position settings selection 3), 69 (ORL: Zero-return limit function), 70 (ORG: Zero-return trigger function), 71 (FOT: forward drive stop), 72 (ROT: reverse drive stop), 73 (SPD: speed / position switching), 74 (PCNT: pulse counter), 75 (PCC: pulse counter clear), no (NO: no assignment)

Default

_FF _FEF _FUF

18

(*2)

06

(*2)

01

Note

1 - 10

Code Function name Monitored data or setting

C021 Terminal [11] function 01

C022 Terminal [12] function 00

C023 Terminal [13] function 03

C024 Terminal [14] function 07

C025 Terminal [15] function 40

C026 Alarm relay terminal function

Intelligent output terminals

C027 [FM] siginal selection

C028 [AM] siginal selection

Analog monitoring

C029 [AMI] siginal selection

Digital current monitor reference

C030

value

C031 Terminal [11] active state 00 (NO) / 01 (NC) 00

C032 Terminal [12] active state 00 (NO) / 01 (NC) 00

C033 Terminal [13] active state 00 (NO) / 01 (NC) 00

C034 Terminal [14] active state 00 (NO) / 01 (NC) 00

terminals

C035 Terminal [15] active state 00 (NO) / 01 (NC) 00

Intelligent output

C036 Alarm relay active state 00 (NO) / 01 (NC) 01

00 (RUN: running), 01 (FA1: constant-speed reached), 02 (FA2: set frequency overreached), 03 (OL: overload notice advance signal (1)), 04 (OD: output deviation for PID control), 05 (AL: alarm signal), 06 (FA3: set frequency reached), 07 (OTQ: over-torque), 08 (IP: instantaneous power failure), 09 (UV: undervoltage), 10 (TRQ: torque limited), 11 (RNT: operation time over), 12 (ONT: plug-in time over), 13 (THM: thermal alarm signal), 19 (BRK: brake release), 20 (BER: braking error), 21 (ZS: 0 Hz detection signal), 22 (DSE: speed deviation maximum), 23 (POK: positioning completed), 24 (FA4: set frequency overreached 2), 25 (FA5: set frequency reached 2), 26 (OL2: overload notice advance signal (2)), 27 (Odc: Analog O disconnection detection), 28 (OIDc: Analog OI disconnection detection), 29 (O2Dc: Analog O2 disconnection detection), 31 (FBV: PID feedback comparison), 32 (NDc: communication line disconnection), 33 (LOG1: logical operation result 1), 34 (LOG2: logical operation result 2), 35 (LOG3: logical operation result 3), 36 (LOG4: logical operation result 4), 37 (LOG5: logical operation result 5), 38 (LOG6: logical operation result 6), 39 (WAC: capacitor life warning), 40 (WAF: cooling-fan speed drop), 41 (FR: starting contact signal), 42 (OHF: heat sink overheat warning), 43 (LOC: low-current indication signal), 44 (M01: general-purpose output 1), 45 (M02: general-purpose output 2), 46 (M03: general-purpose output 3), 47 (M04: general-purpose output 4), 48 (M05: general-purpose output 5), 49 (M06: general-purpose output 6), 50 (IRDY: inverter ready), 51 (FWR: forward rotation), 52 (RVR: reverse rotation), 53 (MJA: major failure), 54(WCO: window comparator O), 55(WCOI: window comparator OI), 56 (WCO2: window comparator O2) (When alarm code output is selected for "C062", functions "AC0" to "AC2" or "AC0" to "AC3" [ACn: alarm code output] are forcibly assigned to intelligent output terminals 11 to 13 or 11 to 14, respectively.)

00 (output frequency), 01 (output current), 02 (output torque), 03 (digital output frequency), 04 (output voltage), 05 (input power), 06 (electronic thermal overload), 07 (LAD frequency), 08 (digital current monitoring), 09 (motor temperature), 10 (heat sink temperature), 12 (general-purpose output YA0)

00 (output frequency), 01 (output current), 02 (output torque), 04 (output voltage), 05 (input power), 06 (electronic thermal overload), 07 (LAD frequency), 09 (motor temperature), 10 (heat sink temperature), 11 (output torque [signed value]), 13 (general-purpose output YA1)

00 (output frequency), 01 (output current), 02 (output torque), 04 (output voltage), 05 (input power), 06 (electronic thermal overload), 07 (LAD frequency), 09 (motor temperature), 10 (heat sink temperature), 14 (general-purpose output YA2)

0.20 x "rated current" to 2.00 x "rated current" (A) (Current with digital current monitor output at 1,440 Hz)

Default

_FF _FEF _FUF

05

00

Rated current of

inverter

Note

1 - 11

Code Function name Monitored data or setting

Low-current indication signal

C038

output mode selection

Low-current indication signal

C039

detection level

C040 Overload signal output mode

C041 Overload level setting 0.0 to 2.00 x "rated current" (A)

C042 Frequency arrival setting for accel. 0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00

C043 Frequency arrival setting for decel. 0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00

C044 PID deviation level setting 0.0 to 100.0 (%) 3.0

Frequency arrival setting for

C045

acceleration (2)

Frequency arrival setting for

C046

deceleration (2)

C052 Maximum PID feedback data 0.0 to 100.0 (%) 100.0

C053 Minimum PID feedback data 0.0 to 100.0 (%) 0.0

Over-torque (forward-driving) level

C055

setting

Levels and output terminal status

Communication function

Adjustment

Others

Meter

adjustment

Over-torque (reverse

C056

regenerating) level setting

Over-torque (reverse driving) level

C057

setting

Over-torque (forward

C058

regenerating) level setting

Electronic thermal warning level

C061

setting

C062 Alarm code output 00 ( disabling), 01 (3 bits), 02 (4 bits) 00

C063 Zero speed detection level 0.00 to 99.99, 100.0 (Hz) 0.00

C064 Heat sink overheat warning level

C071 Communication speed selection

C072 Node allocation 1. to 32. 1.

Communication data length

C073

selection

C074 Communication parity selection 00 (no parity), 01 (even parity), 02 (odd parity) 00

C075 Communication stop bit selection 1 (1 bit), 2 (2 bits) 1

Selection of the operation after

C076

communication error

Communication timeout limit

C077

before tripping

C078 Communication wait time 0. to 1000. (ms) 0.

C079 Communication mode selection 00(ASCII), 01(Modbus-RTU) 00

C081 [O] input span calibration 0. to 9999., 1000 to 6553(10000 to 65530) Factory setting

C082 [OI] input span calibration 0. to 9999., 1000 to 6553(10000 to 65530) Factory setting

C083 [O2] input span calibration 0. to 9999., 1000 to 6553(10000 to 65530) Factory setting

C085 Thermistor input tuning 0.0 to 999.9, 1000. Factory setting

C091 Debug mode enable (Do not change this parameter, which is intended for factory adjustment.) 00

C101 Up/Down memory mode selection 00 (not storing the frequency data), 01 (storing the frequency data) 00

C102 Reset mode selection

C103 Restart mode after reset

C105 FM gain adjustment 50. to 200. (%) 100.

C106 AM gain adjustment 50. to 200. (%) 100.

C107 AMI gain adjustment 50. to 200. (%) 100.

C109 AM bias adjustment 0. to 100. (%) 0.

C110 AMI bias adjustment 0. to 100. (%) 20.

00 (output during acceleration/deceleration and constant-speed operation), 01 (output only during constant-speed operation)

0.0 to 2.00 x "rated current" (A)

00 (output during acceleration/deceleration and constant-speed operation), 01 (output only during constant-speed operation)

0.00 to 99.99, 100.0 to 400.0 (Hz) 0.00

0. to 200. (%) 100.

0. to 100. (%) 80.

0. to 200.0 (°C)

02 (loopback test), 03 (2,400 bps), 04 (4,800 bps), 05 (9,600 bps), 06 (19,200 bps)

7 (7 bits), 8 (8 bits) 7

00 (tripping), 01 (tripping after decelerating and stopping the motor), 02 (ignoring errors), 03 (stopping the motor after free-running), 04 (decelerating and stopping the motor)

0.00 to 99.99 (s) 0.00

00 (resetting the trip when RS is on), 01 (resetting the trip when RS is off), 2 (enabling resetting only upon tripping [resetting when RS is on])

00 (starting with 0 Hz), 01 (starting with matching frequency), 02 (restarting with active matching frequency),03(resetting only trip)

Default

_FF _FEF _FUF

01

Rated current of

inverter

01

Rated current of

inverter

120.

04

02

00

Note

1 - 12

Code Function name Monitored data or setting

C111 Overload setting (2) 0.0 to 2.00 x "rated current" (A)

inal

Ter m

C121 [O] input zero calibration 0. to 9999., 1000 to 6553 (10000 to 65530) Factory setting

C122 [OI] input zero calibration 0. to 9999., 1000 to 6553 (10000 to 65530) Factory setting

ment

Adjust

C123 [O2] input zero calibration 0. to 9999., 1000 to 6553 (10000 to 65530) Factory setting

C130 Output 11 on-delay time 0.0 to 100.0 (s) 0.0

C131 Output 11 off-delay time 0.0 to 100.0 (s) 0.0

C132 Output 12 on-delay time 0.0 to 100.0 (s) 0.0

C133 Output 12 off-delay time 0.0 to 100.0 (s) 0.0

C134 Output 13 on-delay time 0.0 to 100.0 (s) 0.0

C135 Output 13 off-delay time 0.0 to 100.0 (s) 0.0

C136 Output 14 on-delay time 0.0 to 100.0 (s) 0.0

C137 Output 14 off-delay time 0.0 to 100.0 (s) 0.0

C138 Output 15 on-delay time 0.0 to 100.0 (s) 0.0

C139 Output 15 off-delay time 0.0 to 100.0 (s) 0.0

C140 Output RY on-delay time 0.0 to 100.0 (s) 0.0

C141 Output RY off-delay time 0. 0 to 100.0 (s) 0.0

C142 Logical output signal 1 selection 1 Same as the settings of C021 to C026 (except those of LOG1 to LOG6) 00

C143 Logical output signal 1 selection 2 Same as the settings of C021 to C026 (except those of LOG1 to LOG6) 00

Logical output signal 1 operator

C144

selection

C145 Logical output signal 2 selection 1 Same as the settings of C021 to C026 (except those of LOG1 to LOG6) 00

C146 Logical output signal 2 selection 2 Same as the settings of C021 to C026 (except those of LOG1 to LOG6) 00

Logical output signal 2 operator

C147

selection

C148 Logical output signal 3 selection 1 Same as the settings of C021 to C026 (except those of LOG1 to LOG6) 00

C149 Logical output signal 3 selection 2 Same as the settings of C021 to C026 (except those of LOG1 to LOG6) 00

Output terminal operation function

Input terminal response

Logical output signal 3 operator

C150

selection

C151 Logical output signal 4 selection 1 Same as the settings of C021 to C026 (except those of LOG1 to LOG6) 00

C152 Logical output signal 4 selection 2 Same as the settings of C021 to C026 (except those of LOG1 to LOG6) 00

Logical output signal 4 operator

C153

selection

C154 Logical output signal 5 selection 1 Same as the settings of C021 to C026 (except those of LOG1 to LOG6) 00

C155 Logical output signal 5 selection 2 Same as the settings of C021 to C026 (except those of LOG1 to LOG6) 00

Logical output signal 5 operator

C156

selection

C157 Logical output signal 6 selection 1 Same as the settings of C021 to C026 (except those of LOG1 to LOG6) 00

C158 Logical output signal 6 selection 2 Same as the settings of C021 to C026 (except those of LOG1 to LOG6) 00

Logical output signal 6 operator

C159

selection

Input terminal response time

C160

setting 1

Input terminal response time

C161

setting 2

Input terminal response time

C162

setting 3

Input terminal response time

C163

setting 4

Input terminal response time

C164

setting 5

Input terminal response time

C165

setting 6

Input terminal response time

C166

setting 7

Input terminal response time

C167

setting 8

Input terminal response time

C168

setting FW

00 (AND), 01 (OR), 02 (XOR) 00

0. to 200. ( ¯2ms) 1

Default

_FF _FEF _FUF

Rated current of

inverter

Note

Multistage speed/position

C169

Other

determination time

0. to 200. ( ¯10ms) 0

1 - 13

Code Function name Monitored data or setting

H001 Auto-tuning Setting

H002 Motor data selection, 1st motor

H202 Motor data selection, 2nd motor

H003 Motor capacity, 1st motor 0.20 to 75.00 (kW) Factory setting

H203 Motor capacity, 2nd motor 0.20 to 75.00 (kW) Factory setting

H004 Motor poles setting, 1st motor 2, 4, 6, 8, 10 (poles) 4

H204 Motor poles setting, 2nd motor 2, 4, 6, 8, 10 (poles) 4

H005 Motor speed constant, 1st motor 0.001 to 9.999, 10.00 to 80.00 (10.000 to 80.000) 1.590

H205 Motor speed constant, 2nd motor 0.001 to 9.999, 10.00 to 80.00 (10.000 to 80.000) 1. 590

Motor stabilization constant, 1st

H006

motor

Motor stabilization constant, 2nd

H206

motor

Motor stabilization constant, 3rd

H306

motor

H020 Motor constant R1, 1st motor

H220 Motor constant R1, 2nd motor

H221 Motor constant R2, 1st motor

H221 Motor constant R2, 2nd motor

Control constants

H222 Motor constant L, 1st motor 0.01 to 99.99, 100.0 to 655.3 (mH) Depending on motor capacity

H222 Motor constant L, 2nd motor 0.01 to 99.99, 100.0 to 655.3 (mH) Depending on motor capacity

H223 Motor constant Io 0.01 to 99.99, 100.0 to 655.3 (A) Depending on motor capacity

H223 Motor constant Io, 2nd motor 0.01 to 99.99, 100.0 to 655.3 (A) Depending on motor capacity

H224 Motor constant J 0.001 to 9.999, 10.00 to 99.99, 100.0 to 999.9, 1000. to 9999. Depending on motor capacity

H224 Motor constant J, 2nd motor 0.001 to 9.999, 10.00 to 99.99, 100.0 to 999.9, 1000. to 9999. Depending on motor capacity

H030 Auto constant R1, 1st motor

H230 Auto constant R1, 2nd motor

H231 Auto constant R2, 1st motor

H231 Auto constant R2, 2nd motor

H232 Auto constant L, 1st motor 0. 01 to 99.99, 100.0 to 655.3 (mH) Depending on motor capacity

H232 Auto constant L, 2nd motor 0.01 to 99.99, 100.0 to 655.3 (mH) Depending on motor capacity

H233 Auto constant Io, 1st motor 0.01 to 99.99, 100.0 to 655.3 (A) Depending on motor capacity

H233 Auto constant Io, 2nd motor 0.01 to 99.99, 100.0 to 655.3 (A) Depending on motor capacity

H234 Auto constant J, 1st motor 0.001 to 9.999, 10.00 to 99.99, 100.0 to 999.9, 1000. to 9999. Depending on motor capacity

H234 Auto constant J, 2nd motor 0.001 to 9.999, 10.00 to 99.99, 100.0 to 999.9, 1000. to 9999. Depending on motor capacity

00 (disabling auto-tuning), 01 (auto-tuning without rotation), 02 (auto-tuning with rotation)

00 (Hitachi standard data), 01 (auto-tuned data), 02 (auto-tuned data [with online auto-tuning function])

0. to 255. 100.

0.001 to 9.999, 10.00 to 65.53 (Ω)

Default

Note

_FF _FEF _FUF

00

Depending on motor capacity

1 - 14

Code Function name Monitored data or setting

H050 PI proportional gain for 1st motor 0.0 to 999.9, 1000. 100.0

H250 PI proportional gain for 2nd motor 0.0 to 999.9, 1000. 100.0

H051 PI integral gain for 1st motor 0.0 to 999.9, 1000. 100.0

H251 PI integral gain for 2nd motor 0.0 t o 999.9, 1000. 100.0

P proportional gain setting for 1st

H052

motor

P proportional gain setting for 2nd

H252

motor

H060 Zero LV lmit for 1st motor 0.0 to 100.0 100.0

H260 Zero LV lmit for 2nd motor 0.0 to 100.0 100.0

Zero LV starting boost current for

H061

Control constants

1st motor

Zero LV starting boost current for

H261

2nd motor

Terminal selection PI proportional

H070

gain setting

Terminal selection PI integral gain

H071

setting

Terminal selection P proportional

H072

gain setting

H073 Gain switching time 0. to 9999. (ms) 100.

0.01 to 10.00 1. 00

0. to 50. (%) 50.

0.0 to 999.9, 1000. 100.0

0.00 to 10.00 1. 00

Default

Note

_FF _FEF _FUF

1 - 15

Code Function name Monitored data or setting

Operation mode on expansion card

P001

1 error

Operation mode on expansion card

P002

2 error

Encoder pulse-per-revolution

P011

(PPR) setting

P012 Control pulse setting 00 ( ASR), 01 (APR), 02 (APR2), 03 (HAPR) 00

P013 Pulse train mode setting 00 (mode 0), 01 (mode 1), 02 (mode 2) 00

P014 Home search stop position setting 0. to 4095. 0.

P015 Home search speed setting "start frequency" to "maximum frequency" (up to 120.0) (Hz) 5.00

P016 Home search direction setting 00 (forward), 01 (reverse) 00

Home search completion range

P017

setting

Home search completion delay

P018

time setting

Electronic gear set position

P019

selection

Electronic gear ratio numerator

P020

setting

Electronic gear ratio denominator

P021

setting

P022 Feed-forward gain setting 0.00 to 99.99, 100.0 to 655.3 0.00

P023 Position loop gain setting 0.00 to 99.99, 100.0 0.50

P024 Position bias setting -204 (-2048.) / -999. to 2048. 0.

Temperature compensation

P025

thermistor enable

Over-speed error detection level

P026

setting

Speed deviation error detection

P027

level setting

P028 Numerator of motor gear ratio 0. to 9999. 1.

P029 Denominator of motor gear ratio 0. to 9999. 1.

P031 Accel/decel time input selection 00 (digital operator), 01 (option 1), 02 (option 2), 03 (easy sequence) 00

Positioning command input

P032

Optional functions

selection

P033 Torque command input selection 00 (O terminal), 01 (OI terminal), 02 (O2 terminal), 03 (digital operator) 00

P034 Torque command setting 0. to 200. (%) 0.

Polarity selection at the torque

P035

command input via O2 terminal

P036 Torque bias mode 00 (disabling the mode), 01 (digital operator), 02 (input via O2 terminal) 00

P037 Torque bias value -200. to +200. (%) 0.

P038 Torque bias polarity selection 00 (as indicated by the sign), 01 (depending on the operation direction) 00

Speed limit for torque-controlled

P039

operation (forward rotation)

Speed limit for torque-controlled

P040

operation (reverse rotation)

P044 DeviceNet comm watchdog timer 0.00 to 99.99 (s) 1.00

Inverter action on DeviceNet comm

P045

error

DeviceNet polled I/O: Output

P046

instance number

DeviceNet polled I/O: Input

P047

instance number

Inverter action on DeviceNet idle

P048

mode

DeviceNet motor poles setting for

P049

RPM

P055 Pulse-string frequency scale 1.0 to 50.0 (kHz) 25. 0

Time constant of pul se-string

P056

frequency filter

P057 Pulse-string frequency bias -100. to +100. (%) 0.

P058 Pulse-string frequency limit 0. to 100. (%) 100.

00 (tripping), 01 (continuing operation) 00

128. to 9999., 1000 to 6553(10000 to 65535) (pulses) 1024.

0. to 9999., 1000 (10000) (pulses) 5.

0.00 to 9.99 (s) 0.00

00 (feedback side), 01 (commanding side) 00

0. to 9999. 1.

00 (no compensation), 01 (compensation) 00

0.0 to 150.0 (%) 135.0

0.00 to 99.99, 100.0 to120.0 (Hz) 7.50

00 (digital operator), 01 (option 1), 02 (option 2) 00

00 (as indicated by the sign), 01 (depending on the operation direction) 00

0.00 to "maximum frequency" (Hz) 0.00

00 (tripping), 01 (tripping after decelerating and stopping the motor), 02 (ignoring errors), 03 (stopping the motor after free-running), 04 (decelerating and stopping the motor)

20, 21, 100 21

70, 71, 101 71

00 (tripping), 01 (tripping after decelerating and stopping the motor), 02 (ignoring errors), 03 (stopping the motor after free-running), 04 (decelerating and stopping the motor)

0, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30, 32, 34, 36, 38 (poles)

0.01 to 2.00 (s) 0.10

Default

Note

_FF _FEF _FUF

01

0

1 - 16

Code Function name Monitored data or setting

P060 Multistage position setting 0

P061 Multistage position setting 1

P062 Multistage position setting 2

P063 Multistage position setting 3

P064 Multistage position setting 4

P065 Multistage position setting 5

P066 Multistage position setting 6

P067 Multistage position setting 7

P068 Zero-return mode selection 00(Low) / 01 (Hi1) / 00 (Hi2) 00

Absolute position control

P069 Zero-return direction selection 00 (FW) / 01 (RV) 00

P070 Low-speed zero-return frequency 0.00 to 10.00 (Hz) 0.00

High-speed zero-return

P071

frequency

Position rang e specificatio n

P072

(forward)

Position rang e specificatio n

P073

(reverse)

P074 Teaching selection

Easy sequence user parameter U

P100

(00)

Easy sequence user parameter U

P101

(01)

Easy sequence user parameter U

P102

(02)

Easy sequence user parameter U

P103

(03)

Easy sequence user parameter U

P104

(04)

Easy sequence user parameter U

P105

(05)

Easy sequence user parameter U

P106

(06)

Easy sequence user parameter U

P107

(07)

Easy sequence user parameter U

P108

(08)

Easy sequence user parameter U

P109

Easy sequence function

(09)

Easy sequence user parameter U

P110

(10)

Easy sequence user parameter U

P111

(11)

Easy sequence user parameter U

P112

(12)

Easy sequence user parameter U

P113

(13)

Easy sequence user parameter U

P114

(14)

Easy sequence user parameter U

P115

(15)

Position setting range reverse side to forward side (upper 4 digits including “-“)

0.00 to 99.99 / 100.0 to Maximum frequency setting, 1st motor (Hz) 0.00

0 to 268435455 (when P012 = 02) 0 to 1073741823 (when P012 = 03) (upper 4 digits)

-268435455 to 0 (when P012 = 02)

-1073741823 to 0 (when P012 = 03) (upper 4 digits)

00 (X00) / 01 (X01) / 02 (X02) / 03 (X03) / 04 (X04) / 05 (X05) / 06 (X06) / 07 (X07) /

0. to 9999., 1000 to 6553 (10000 to 65535) 0.

Default

_FF _FEF _FUF

0

268435455

-268435455

00

Note

1 - 17

Code Function name Monitored data or setting

Easy sequence user parameter U

P116

(16)

Easy sequence user parameter U

P117

(17)

Easy sequence user parameter U

P118

(18)

Easy sequence user parameter U

P119

(19)

Easy sequence user parameter U

P120

(20)

Easy sequence user parameter U

P121

(21)

Easy sequence user parameter U

P122

(22)

Easy sequence user parameter U

P123

(23)

Easy sequence user parameter U

P124

(24)

Easy sequence user parameter U

P125

Easy sequence function

(25)

Easy sequence user parameter U

P126

(26)

Easy sequence user parameter U

P127

(27)

Easy sequence user parameter U

P128

(28)

Easy sequence user parameter U

P129

(29)

Easy sequence user parameter U

P130

(30)

Easy sequence user parameter U

P131

(31)

0. to 9999., 1000 to 6553 (10000 to 65535) 0.

Default

Note

_FF _FEF _FUF

1 - 18

Code Function name Monitored data or setting

U001 User-selected function 1 no/d001 to P131 no

U002 User-selected function 2 no/d001 to P131 no

U003 User-selected function 3 no/d001 to P131 no

U004 User-selected function 4 no/d001 to P131 no

U005 User-selected function 5 no/d001 to P131 no

U006 User-selected function 6 no/d001 to P131 no

U007 User-selected function 7 no/d001 to P131 no

U008 User-selected function 8 no/d001 to P131 no

User parameters

U009 User-selected function 9 no/d001 to P131 no

U010 User-selected function 10 no/d001 to P131 no

U011 User-selected function 11 no/d001 to P131 no

U012 User-selected function 12 no/d001 to P131 no

Default

_FF _FEF _FUF

Note

1 - 19

1.3 Code display system and key operations

This section describes typical examples of digital operator operation (in basic and full display modes) and an example of special digital operator operation in extended function mode U.

The initial display on the monitor screen after power-on depends on the setting of function "b038". For details, see Section 4.2.81, "Initial-screen selection," (on page 4-76).

When the setting of function "b038" is "01" (factory setting), the monitor initially shows as

the setting of function "d001" (output frequency monitoring). Pressing the key in this status

changes the display to .

Note: The display contents on the monitor depend on the settings of functions "b037" (function code

display restriction), "b038" (initial-screen selection), and "b039" (automatic setting of user parameters). For details, see Sections 4.2.80, "Function code display restriction," (on page 4-74),

4.2.81, "Initial-screen selection," (on page 4-76), and 4.2.82, "Automatic user-parameter setting," (on page 4-77).

Item Function code Data Description

00 Full display

Function code display

restriction

Initial-screen selection

(Initial display at

power-on)

user-parameter settings

*1 Not displayed with the factory setting

b037

b038

(*1)

b039

(*1)

01 Function-specific display 02 User setting 03 Data comparison display 04 Basic display (factory setting)

00

01 d001 (output frequency monitoring) 02 d002 (output current monitoring) 03 d003 (rotation direction minitoring) 04 d007 (Scaled output frequency monitoring) 05 F001 (output frequency setting) 00 Disable Selection of automatic 01 Enable

Screen displayed when the [STR] key was pressed last (same as the operation on the SJ300 series)

* The following procedure enables you to turn the monitor display back to or (*1)

regardless of the current display mode:

- Hold down the key for 3 seconds or more. The monitor shows and (*1)

FUNC

alternately.

During this status, press the key. The monitor will show only or (*1),

which is shown when the is pressed.

FUNC

*1 The monitor shows only when the motor driven by the inverter is stopped. While the

motor is running, the monitor shows an output frequency.

FUNC

1 - 20

1.3.1 Example of operation in basic display mode ("b037" = "04" [factory setting])

- Only basic parameters can be displayed in basic display mode. (All parameters in monitor mode, four parameters in function mode, or 20 parameters in extended function mode)

- Other parameters are not displayed. To display all parameters, select the full display mode ("b037" = "00").

No. Display code Item

1 d001 to d104 Monitor display 2 F001 Output frequency setting 3 F002 Acceleration (1) time setting 4 F003 Deceleration (1) time setting 5 F004 Operation direction setting 6 A001 Frequency source setting 7 A002 Run command source setting 8 A003 Base frequency setting

9 A004 Maximum frequency setting 10 A005 [AT] selection 11 A020 Multispeed frequency setting 12 A021 Multispeed 1 setting 13 A022 Multispeed 2 setting 14 A023 Multispeed 3 setting 15 A044 1st control method 16 A045 V/f gain setting 17 A085 Operation mode selection 18 b001 Selection of restart mode 19 b002 Allowable under-voltage power failure time 20 b008 Retry-after-trip selection 21 b011 Retry wait time after trip 22 b037 Function code display restriction 23 b083 Carrier frequency setting 24 b084 Initialization mode selection

25 b130

26 b131 Setting of overvoltage suppression level 27 C021 Setting of intelligent output terminal 11 28 C022 Setting of intelligent output terminal 12 29 C036 Alarm relay active state

Selection of overvoltage suppression function

Note:

If a desired parameter is not displayed, check the setting of function "b037" (function code display restriction). To display all parameters, specify "00" for "b037".

1 - 21