Hitachi SJ100 Supplemental Sheet

SJ100 Series Supplemental Sheet (NBM585XA-12)

ATTENTION

Note 1:

The revision level of the MFG No. distinguishes the following changes in Function Codes A81, C31
and C32

side of the housing. The changes apply to inverters, which carry a revision code per the table below.
When you copy parameters between units manufactured before and after this change with a copy unit,
confirm Function Codes C31 and C32.

Example of MFG No. :

112H

Revision
A…K…1A…1K…2A…2H…
Revision Increment--------

. The Inverter MGF No. is shown on the Specification Label (Nameplate), located on the right

T123451J001

Æ

Inverter Models

SJ100-002NFU 2E 2H

SJ100-004-022NFU 2G 2H

SJ100-037LFU 2E 2H

SJ100-055,075LFU K M

SJ100-004HFU 2F 2H

SJ100-007-040HFU 2G 2H

SJ100-055,075HFU L M

Revision

before change

Applied

Revision

Page

3-18

Changes

OLD DEFAULT SETTING:

“A” Function

Func.
Code

Name Description

A81 AVR function

select

Automatic (output) voltage
regulation, selects from three

Run-

time

Edit

Defaults DOP,DRW,DOP+

EU/

US

02

Units

Func.
Code

- F-03 AVR

types of AVR functions, three
option codes:
00…AVR enabled
01…AVR disabled
02…AVR enabled except
during deceleration

NEW DEFAULT SETTING:

*Inverters manufactured after the revision as defined in Note 1 will have the following settings:

Func.
Code

Name Description

A81 AVR function

select

“A” Function

Automatic (output) voltage
regulation, selects from three

Run-

time

Edit

Defaults DOP,DRW,DOP+

EU/

US

00

Units

Func.
Code

- F-03 AVR

types of AVR functions, three
option codes:
00…AVR enabled
01…AVR disabled
02…AVR enabled except
during deceleration

Name

MODE

Name

MODE

1/2

NBM585XA-12

Page

3-32

Changes

OLD DEFAULT SETTING:

“C” Function

Func.
Code

C31 Reserved Factory use only; do not

Name Description

change

Run-

time

Edit

Defaults DOP,DRW,DOP+

EU/

US

00

Units

Func.
Code

- F-35 OUT-TM

Name

O/C-1

C32 Terminal 11

active state

NEW DEFAULT SETTING:

*Inverters manufactured after the revision as defined in Note 1 will have the following settings:

“C” Function

Func.
Code

C31 Terminal 11

C32 Terminal 12

Name Description

active state

active state

Select logic convention, two
option codes:
00…normally open [NO]
01…normally closed [NC]

Select logic convention, two
option codes:
00…normally open [NO]
01…normally closed [NC]

Select logic convention, two
option codes:
00…normally open [NO]
01…normally closed [NC]

Run-

time

Edit

00

Defaults DOP,DRW,DOP+

EU/

US

00

00

- F-35 OUT-TM
O/C-2

Units

Func.
Code

- F-35 OUT-TM
O/C-1

- F-35 OUT-TM
O/C-2

Name

B-7

OLD DEFAULT SETTING:

“C” Group Parameters Default Setting User Setting

Func. Code Name -FE(Europe) -FU(USA)

C31 Factory-set - -

C32 Terminal 11 active state 00 00

NEW DEFAULT SETTING:

*Inverters manufactured after the revision as defined in Note 1 will have the following settings:

“C” Group Parameters Default Setting User Setting

Func. Code Name -FE(Europe) -FU(USA)

C31 Terminal 11 active state 00 00

C32 Terminal 12 active state 00 00

2/2

NBM585XA-12