Hitachi RAS-D10CDK, RAC-D10CDK, RAS-D13CDK, RAC-D13CDK User Manual

- 1 -

ENGLISH

– 1 –

HSILGNE

INDOOR UNIT/OUTDOOR UNIT

SPLIT TYPE AIR CONDITIONER

MODEL

RAS-D10CDK/RAC-D10CDK RAS-D13CDK/RAC-D13CDK

Instruction manual

Page 1~20

To obtain the best performance and ensure years of trouble free use, please read this instruction manual completely.

21~40

OUTDOOR UNIT INDOOR UNIT

RAS-D10CDK RAS-D13CDK

ENGLISH

RAC-D10CDK RAC-D13CDK

- 3 -

SAFETY PRECAUTION

•

Please read the “Safety Precaution” carefully before operating the unit to ensure correct usage of the unit.

•

Pay special attention to signs of“ Warning” and “ Caution”. The “Warning” section contains matters which,if

“

not observed strictly, may cause death or serious injury. The serious consequences if not observed properly. Please observe all instructions strictly to ensure safety. The signs indicate the following meanings.

•

Make sure to connect earth line.

Indicates the instructions that must be followed.

Please keep this manual after reading.

•

PRECAUTIONS DURING INSTALLATION

Do not reconstruct the unit.

• Water leakage, fault, short circuit or ﬁre may occur if you reconstruct the unit by yourself.

Please ask your sales agent or qualified technician for the installation of

• your unit. Water leakage, short circuit or ﬁ re may occur if you install the unit

WARNING

by yourself. Please use earth line.

• Do not place the earth line near water or gas pipes, lightning-conductor, or the earth line of telephone. Improper installation of earth line may cause electric shock.

Caution” section contains matters which may result in

The sign in the ﬁgure indicates prohibition.

CAUTION

•

A R N

•

A circuit breaker should be installed depending on the mounting site of the

• unit. Without a circuit breaker, the danger of electric shock exists.

Do not install near location where there is ﬂammable gas. The outdoor unit

• may catch ﬁre if ﬂammable gas leaks around it.

Please ensure smooth ﬂow of water when installing the drain hose.•

PRECAUTIONS DURING SHIFTING OR MAINTENANCE

Should abnormal situation arises (like burning smell), please stop operating the unit and turn off the circuit breaker. Contact your agent. Fault, shor t circuit or ﬁre may occur if you continue to operate the unit under abnormal situation.

Please contact your agent for maintenance. Improper self maintenance may cause electric shock and ﬁre.

Please contact your agent if you need to remove and reinstall the unit. Electric shock or ﬁre may occur if you remove and reinstall the unit yourself improperly.

If the supply cord is damaged, it must be replaced by the special cord obtainable at authorized service/parts centers.

PRECAUTIONS DURING OPERATION

A R N

I N G

Avoid an extended period of direct air ﬂ ow for your health.•

Do not put objects like thin rods into the panel of blower and suction side because

• the high-speed fan inside may cause danger.

Do not use any conductor as fuse wire, this could cause fatal accident.•

During thunder storm, disconnect and turn off the circuit breaker.•

- 2 -

PRECAUTIONS DURING OPERATION

The product shall be operated under the manufacturer speciﬁcation and not

•

for any other intended use.

Do not attempt to operate the unit with wet hands, this could cause fatal accident.•

When operating the unit with burning equipments, regularly ventilate the

•

room to avoid oxygen insufﬁciency.

Do not direct the cool air coming out from the air-conditioner panel to face

•

household heating apparatus as this may affect the working of apparatus such as the electric kettle, oven etc.

Please ensure that outdoor mounting frame is always stable, firm and

•

without defect. If not, the outdoor unit may collapse and cause danger.

Do not splash or direct water to the body of the unit when cleaning it as this may

•

cause short circuit.

Do not use any aerosol or hair sprays near the indoor unit. This chemical

•

can adhere on heat exchanger ﬁn and blocked the evaporation water ﬂow to drain pan. The water will drop on tangential fan and cause water splashing out from indoor unit.

ENGLISH

A R N

I N G

Please switch off the unit and turn off the circuit breaker during cleaning, the high-

•

speed fan inside the unit may cause danger.

Turn off the circuit breaker if the unit is not to be operated for a long period.•

Do not climb on the outdoor unit or put objects on it.•

Do not put water container (like vase) on the indoor unit to avoid water

•

dripping into the unit. Dripping water will damage the insulator inside the unit and causes short-circuit.

Do not place plants directly under the air ﬂ ow as it is bad for the plants.•

When operating the unit with the door and windows opened, (the room humidity is always above

•

80%) and with the air deﬂ ector facing down or moving automatically for a long period of time,water will condense on the air deﬂector and drips down occasionally. This will wet your furniture.Therefore, do not operate under such c If the amount of heat in the room is above the cooling or heating capability of the unit (for example:

•

more people entering the room, using heating equipments and etc.), the preset room temperature cannot be achieved.

•

This appliance is not intended for use by young children or infirm persons unless they have been

adequately supervised by a responsible person to ensure that they can use this appliance safely.

•

Young children should be supervised to ensure that they do not play with the appliance.

ondition for a long time.

- 3 -

- 5 -

PRODUCT PERFORMANCE AND TECHNICAL PARAMETERS

Fuzzy control

Quiet

Fuzzy control

•

High performance rotary

• compressor

Low noise air intake system

•

Temperature sensing automatic

• dehumidify cation

Sleep mode with automatic

• adjustable temperature controls

High performance timer

•

Remote control swing mode

•

Automatic parking air vent grilles

•

Automatic fan speed adjustment

•

Left right drain hoses

•

Automatic functions

•

High sensing thermostat

•

3 minute delay circuitry

•

3 fan speed selection

•

Flared piping joints

•

Instant dehumidifying functions

•

High performance cooling functions

•

Stainless ﬁlter

•

Fuzzy control

The common timer controls will always switch on the air conditioner at a predetermined time that could cause over cooling, however, with this advanced fuzzy control system the air conditioner will be either switched on before preset time or delayed depending on the indoor temperature changes, allowing the room temperature to reach the preset temperature within an optimal time frame, as such it will create an optimal air conditioned environment and will also provide greater savings on electrical energy consumption.

Low noise air intake system

This newly modiﬁed low noise air intake system allows better and smoother air ﬂ ows that will provide a quiet and refreshing environment.

Sleep mode with automatic adjustable temperature controls

After adjusting the sleep mode timer before sleep, the t emp erature w ill be automatically controlled and adjusted accordingly to the lowering or body temperature during sleep and lower temperature throu g h o u t the ni g h t , to p r o v i d e a c o n d u cive environment for a good sleep.

An hour after setting the sleep mode timer, the air conditioner wi ll automatically adjust the optimal temperature; during summer it will be adjusted to 2°C higher than the preset room temperature, and the timer can be set at a 1-hour, 2-hour, 3-hour and 7-hour cycle. All can be set by pressing the control buttons that save you the trouble to preset the required operating modes before sleep.

Temperature sensing automatic dehumidiﬁcation

Hitachi air conditioners are specially equipped with pricise and reliable temperature sensing automatic dehumidiﬁ cation function, that automatically operates the dehumidiﬁ cation whenever the room temperature exceeds the preset temperature and it stops whenever the room temperature falls back within the preset temperature as such it stabilizes the temperature and provides a more conducive environment for the user.

Well designed unit body

The indoor unit incorporates the latest design and has a non-bulky body that measures 211 x 780 x 280mm.

- 4 -

NAMES AND FUNCTIONS OF EACH PART

INDOOR UNIT

AIR FILTER

To prevent dust from coming into the door unit. (Refer page 15)

INDOOR UNIT INDICATORS

Light indicator showing the operating condition. (Refer page 6)

FRONT PANEL

SUPPORT PANEL

HORIZONTAL DEFLECTOR • VERTICAL DEFLECTOR (AIR OUTLET)

(Refer page 13)

REMOTE CONTROL

Send out operation signal to the indoor unit. So as to operate the whole unit. (Refer page 7)

ENGLISH

OUTDOOR UNIT

MODEL NAME AND DIMENSIONS

MODEL WIDTH(mm) HEIGHT(mm) DEPTH(mm) RAS-D10CDK, RAS-D13CDK 780 280 211 RAC-D10CDK, RAC-D13CDK 420 299792

DRAIN PIPE

Condensed water drain to outside.

CONNECTING CORD

AIR INLET (BACK, LEFT SIDE)

AIR OUTLET

- 5 -

- 7 -

ATTACHING AND REMOVING FRONT PANEL

While gripping both the left and right hand edges

• [recessed in the front housing] of the front panel, lift up to open the front panel.

After completion of job, sl ightly lif t up th e front

• panel and pull down to close the front panel. Ensure that the 3 sets of left, centre and right clips are fully secured.

RECEIVABLE INDICATOR FUNCTIONS

Operation Lamp (YELLOW)

This lamp lights during operation.The lamp ﬂashes when the defrosting is functioning in "heating" mode or at the time the pre-heating is operating in 2 to 3 minutes.

Timer Lamp (ORANGE)

This lamp lights when the timer is working. The lamp ﬂashes periodically when any abnormality occurs in the indoor unit.

Temporary Switch

OPERATION INDICATOR

TEMPORARY SWITCH

When the remote control device is not functioning, use the Temporary Switch mode

(1) When the Temporary Switch is pressed, the unit will operate as per the previous setting.

(2) Press the Temporary Switch a second time will stop the operations of the air conditioner unit.

AUTO RESTART FUNCTION

In the event of power failure, the air conditioner will restart automatically.

In the event of power failure during TIMER operation, the timer will be reset and the unit will begin or stop operating under a new timer setting.

- 6 -

NAMES AND FUNCTIONS OF REMOTE CONTROL UNIT

CIRCULATION / START

DEHUMIDIFY / START

COOLING / START

FAN

FAN SPEED LOW

MED HI

SLEEP TIMER

STOP

TIMER SELECTOR ON TIMER OFF TIMER

AUTO SWING

REMOTE CONTROLLER

This controls the operation of the indoor unit. The range of control is about 7 meters. If indoor lighting is controlled electronically, the range of control may be shorter. This unit can be ﬁ xed on a wall using the ﬁxture provided. Before ﬁxing it, make sure the indoor unit can be controlled from the remote controller.

Transmission sign

The transmission sign blinks when a signal is sent.

Display

This indicates the room temperature selected, current time, timer status, function and intensity of circulation selected.

AIR CIRCULATION button

Use this button to set air circulation in the room or start operation.

DEHUMIDIFYING button

Use this button to reduce water quantity in the room or start operation.

COOLING button

Use this button to set cooling mode in the room or start operation.

RESET button

ENGLISH

STOP button

Press this button to stop operation only.

SLEEP button

Use this button to set the sleep timer.

FAN SPEED selector

This determines the fan speed. Every time you press this button,the intensity of circulation will change from (AUTO) to (HI) to (MED) to (LOW) (during the (AIR CIRCULATION) mode, from HI to

MED to LOW).

AUTO SWING button

Controls the angle of the horizontal air deﬂector and to turn off ﬁlter lamp.

TEMPERATURE button

Use this button to raise or lower the temperature setting. (Keep pressed, and the value will change more quickly.)

OFF-TIMER button ON-TIMER button

Select the turn OFF time.

Select the turn ON time.

Precautions for Use

Do not put the remote controller in the following places.

• In direct sunlight.

• In the vicinity of a heater.

•

Handle the remote controller carefully. Do not drop it on the ﬂoor, and

• protect it from water. Once the outdoor unit stops, it will not restart for about 3 minutes

• (unless you turn the power switch off and on or unplug the power cord and plug it in again). This is to protect the device and does not indicate a failure. If you press the FUNCTION selector button during operation,the

• device may stop for about 3 minutes for protection.

- 7 -

- 9 -

COOLING OPERATION

STOP

Use the device for cooling when the outdoor temperature is 21-43°C. If humidity is very high (over 80°C) indoors, some dew may form on the air outlet grille of the indoor unit.

Press the button so that the display indicates

(COOL).

Set the desired FAN SPEED with the (FAN SPEED) button (the display indicates the setting).

(AUTO) :The FAN SPEED is HI at ﬁ rst and varies to MED or

LOW automatically when the preset temperature has been reached.

(HI) : Economical as the room will become cool quickly.

(MED) : Fan speed slow.

(LOW) :Fan speed slower.

Set the desired room temperature with the TEMPERATURE button (the display indicates the setting).

The range of 25-28°C is recommended as the room temperature for cooling. If the temperature setting is 27°C, the room temperature will be controlled at around 27°C.

The temperature setting and the actual room temperature may vary somewhat depending on conditions.

Press the (COOLING) button. Cooling operation starts with a beep. Press the (STOP) button to stop operation. The cooling function does not start if the temperature setting is higher than the current room temperature (even though the (OPERATION) lamp lights). The cooling function will start as soon as you set the temperature below the current room temperature.

■

As the settings are stored in memory in the remote controller, you only have to press the (COOLING) button next time.

- 8 -

DEHUMIDIFYING OPERATION

STOP

Press the

(DEHUMIDIFY) button.

STOP

Use the device for dehumidifying when the room temperature is over 16°C. When it is under 15°C, the dehumidifying function will not work.

Press the (DEHUMIDIFY) button. The FAN SPEED is set at LOW automatically. The FAN SPEED button does not work.

Set the desired room temperature with the TEMPERATURE button (the display indicates the setting).

The range of 20-26 room temperature for dehumidifying.

Press the (DEHUMIDIFY). Dehumidifying operation starts with a beep. Press the (STOP) button to stop operation.

C is recommended as the

ENGLISH

■

As the settings are stored in memory in the remote controller, you only have to press the (DEHUMIDIFY) button next time.

Dehumidifying Function

When the room temperature is higher than the temperature setting: The device will dehumidify the room, reducing the room temperature to the preset level. When the room temperature is lower than the temperature setting: Dehumidifying will be performed at the temperature setting slightly lower than the current room temperature, regardless of the temperature setting. The function will stop (the indoor unit will stop emitting air) as soon as the room temperature becomes lower than the setting temperature.

- 9 -

- 11 -

CIRCULATION OPERATION

STOP

■

Press the button so that the display indicates (CIRCULATE).

Press the FAN SPEED button and select the desired FAN SPEED (the display indicates your choice).

Press the te mperature con trol button to s et to t he desired temperature.

Press the (CIRCULATION) button. Circulating operation starts with a beep. Press the (STOP) button to stop operation.

As the settings are stored in memory in the remote controller, you only have to press the (CIRCULATION) button next time.

Circulation Function

During circulation operation, compressor will not be running and there is no cooling operation with only

•

indoor fan running. When the setting temperature is higher than roomtemperature, indoor fan will stop running.

•

- 10 -

HOW TO SET THE SLEEP TIMER

1 hour 2 hours 3 hours 7 hours

Sleep timer off

Press the (SLEEP) button, and the display changes as shown below.

Sleep timer

Sleep Timer:

of hours and then turn off.

Point the signal window of the remote controller toward the indoor unit, and press the SLEEP button.

The timer information will be displayed on the remote controller.

SLEEP

The TIMER lamp lights with a beep from the indoor unit. When the sleep timer has been set, the display indicates the turn-off time.

Explanation of the sleep timer

Mode Indication

ENGLISH

The device will continue working for the designated number

The device will control the FAN SPEED and room temperature automatically so as to be quiet and good for people’s health. You can set the sleep timer to turn off after 1, 2, 3 or 7 hours. The FAN SPEED and room temperature will be controlled as shown below.

Operation with the sleep timer

Function Operation

Cooling

“ ”

and

dehumidifying

“ ”

Fan

“ ”

The room temperature will be controlled 2°C above the setting temperature and the FAN SPEED will be set to LOW setting 60 minutes after the setting of the sleep timer.

The settings of room temperature and circulation are varied.

Sleep timer set

60 minutes later 3 hours later

2 hours later

7 hours later

- 11 -

- 13 -

HOW TO SET THE TIMER

1 2 3 9 1 0 1 1 1 2

■

ON Timer and OFF Timer are available.

OFF Timer Reservation

OFF TIME setting

Select the OFF TIME by pressing the (OFF) Button.

• Setting time will change according to the below sequence

• when you press the button.

1 hour interval

■

Operation stop at setting time

ON Timer Reservation

ON TIME setting

Select the ON TIMER by pressing the

• Setting time will change according to the below sequence.

•

1 hour interval

(ON) Button.

■

O p e r a t i o n w i ll st a r t fo r se t t i ng te m pe r at u re at set t in g t i me (Th e starting time may different depend on th e r o om te m pera t ure an d s e t temperature).

- 12 -

+ 28 hidden pages