QI-150P Modular User Manual(NA)
Model Name: QI-150P
Ver. 1.0 2018.07.12
Hitachi Information & Telecomunication Engineering,Ltd.
All Rights Reserved,Copyright© 2018 Hitachi Information & Telecommunication Engineering,Ltd. 1
Revision
Date
Description
Ver. 1.0
July 12, 2018
Initial release
Revision history
All Rights Reserved,Copyright© 2018 Hitachi Information & Telecommunication Engineering,Ltd. 2
1. Introduction
This document describes notes on using wireless communication module (model name:
QI-150P) in North America.
Country list:
USA
2. Features
WiGig and IEEE 802.11ad-2012 standard compliant
- Supported Frequency Range : 57~64GHz
- Supported Channel: 1~3 (subject to regional regulatory restrictions)
- Supported Data Rate: MCS0, MCS1 (385Mbps) ~ MCS12 (4.6Gbps)
- Supported Modulation: π/2-BPSK, π/2-QPSK, π/2-16QAM
-state) host interface
-S3-A-E form factor: 22 x 30mm
following potential applications
- Instant wireless sync
- Wireless display
- Cordless computing (i.e. wireless docking)
- Internet access.
-state) host interface
-2700
-2702
All Rights Reserved,Copyright© 2018 Hitachi Information & Telecommunication Engineering,Ltd. 3
3. FCC compliance information
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
(Section 15.21)
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device
could void the user's authority to operate the equipment.
(FCC 2.1091 and FCC 2.1093)
RF exposure warning
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not be
co-located or operating in conjunction with any other antenna or transmitter.
All Rights Reserved,Copyright© 2018 Hitachi Information & Telecommunication Engineering,Ltd. 4
End-users and installers must be provide with antenna installation instructions
No.
Manufacturer
Part No.
Antenna Type
Peak Gain
1
STAF
T17-002-1054
Dipole Antenna
3 dBi for 2.4 & 5 GHz
and transmitter operating conditions for satisfying RF exposure compliance.
This radio transmitter FCCID: 2AOV3QI-150P has been approved by FCC to operate
with the antenna types listed below with the maximum permissible gain and required
antenna impedance for each antenna type indicated. Antenna types not included in
this list, having a gain greater than the maximum gain indicated for that type,
are strictly prohibited for use with this device.
Antenna List
Note: The antenna connector is Reverse SMA type.
All Rights Reserved,Copyright© 2018 Hitachi Information & Telecommunication Engineering,Ltd. 5
Loading...