Hitachi L19DP03C Schematic

No. 0250

«MODEL NAMES»

L19DP03C L19DP03U L19HP03C

SERVICE MANUAL MANUEL D'ENTRETIEN WARTUNGSHANDBUCH

CAUTION:

Before servicing this chassis, it is important that the service technician read the “Safety Precautions” and “Product Safety Notices” in this service manual.

ATTENTION:

Avant d’effectuer l’entretien du châssis, le technicien doit lire les «Précautions de sécurité» et les «Notices de sécurité du produit» présentés dans le présent manuel.

VORSICHT:

Vor Öffnen des Gehäuses hat der Service-Ingenieur die „Sicherheitshinweise“ und „Hinweise zur Produktsicherheit“ in diesem Wartungshandbuch zu lesen.

L19HP03U

Data contained within this Service manual is subject to alteration for improvement.

Les données fournies dans le présent manuel d’entretien peuvent faire l’objet de modifications en vue de perfectionner le produit.

Die in diesem Wartungshandbuch enthaltenen Spezifikationen können sich zwecks Verbesserungen ändern.

FOR ALL PARTS PLEASE MAKE

CONTACT WITH ASWO.

FOR YOUR LOCAL OUTLET GO TO

www.aswo.com

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT

Colour Television

May 2009

TABLE OF CONTENTS

1 INTRODUCTION....................................................................................................3

2 GENERAL DESCRIPTION...................................................................................3

3 POWER CONSUMPTION.....................................................................................6

4 MICROCONTROLLER PORT CONFIGURATION.........................................6

5 SIDE BOARDS AND CONNECTORS .................................................................7

5.1 Keypad .........................................................................................................................................7

5.2 Infrared & LED ...........................................................................................................................7

5.3 DVB-T .........................................................................................................................................8

5.4 DVD.............................................................................................................................................9

5.5 LVDS .........................................................................................................................................11

5.6 Inverter.......................................................................................................................................12

6 IC SPECIFICATIONS..........................................................................................13

6.1 Microcontoller/Video&Audio Processor (VCT4953G) ............................................................13

6.2 Scaler/De-interlacer (MST5x7A-M)..........................................................................................16

6.3 Audio Amplifier (TDA2822).....................................................................................................19

6.4 HeadPhone Amplifier (TDA1308T) ..........................................................................................19

6.5 Audio Matrix Switch (TEA6422D) ...........................................................................................20

6.6 HDMI Receiver (ANX9021) ....................................................................................................21

6.7 Video Switch (PI5V512)...........................................................................................................23

6.8 Tuner (DTT71306).....................................................................................................................24

6.9 SAW Filter (X6966M)...............................................................................................................25

6.10 I2C Switch (74HCT4053)..........................................................................................................26

6.11 Audio DAC (CS4334)................................................................................................................27

6.12 SPDIF Switch (NLAST4599) ....................................................................................................28

1 INTRODUCTION

The purpose of this document is to define the operation of 17MB27 chassis, capable of driving 15” and 19” TFT LCD panels. It is aimed to provide information to engineering staff to understand the operation and specs of the TV. The other related technical documents are given in Table1:

Title

1 17MB27 schematics 2 IR receiver and LED display board schematics 3 Keypad board schematics 4 DVD module card schematics 5 DVB-T module card schematics

Table1.1: Related documents

2 GENERAL DESCRIPTION

The system is a low to mid end; 15” and 19” TFT TV solution basically for EU market with VCT4913G microcontroller / video audio processor chip on a 2-layer PCB. Since the target market is EU, the first release of the TV will support PAL/SECAM B/G/D/K/I/L/L’.

The target panels are 15” 1024x768 and 19”w 1440x900 TFT-LCD panels. A DVD loader is used to read DVD content and a DVB-T module card is used to support DVB-T. 15” TV will use 12V/4.16A DC adapter; 19” TV will use 12V/5.83A DC adapter.

Inputs

• 1xTuner (both analog and DVB-T)

• 1xDVD

• 1xScart

• 1xPC (VGA) (optional) (supports also YPbPr)

• 2xHDMI (optional)

• 1xBack AV (optional)

Outputs

• Speaker (stereo, 2x16 , 2x2Watt)

• Headphone (stereo) (optional)

• Audio line out (stereo) (optional)

• DVD/DVB-T coaxial SPDIF out(optional)

General default features

• Multi System Reception: PAL-SECAM BG-DK-I/I’-L/L’

• Menu system (multi language)

• 100 program storage locations

• OSD (on-screen display)

• Teletext

• IR Control (RC5 and other customer specific protocols)

• “No Ident” Timer

• Child Lock

• Sleep Timer

• WSS (16:9/4:3 Aspect Ratio Auto Switch)

Sound Features

• Equalizer

• FM Radio

• Linear Stereo

• German-NICAM Stereo

• 5-Band Equalizer Control

• SRS TRU Surround (OPT)

• SRS TRU Bass (OPT)

• BBE, WOW (OPT)

Picture Features

• 4:3 PANEL --- 4:3, 16:9, Auto

• WIDE PANEL---4:3,16:9, Auto(opt), Subtitle(opt), Zoom(opt), Panoramic(opt)

• Picture Modes ( Bright, Standard, Soft)

• Media Window Enhancement (MWE)

• White balance settings (warm/normal/cool) for TV&PC

• Backlight brightness setting (movie/normal/bright)

• Multi System Reception : PAL-SECAM BG-DK-I/I’-L/L’

• NTSC Video Playback

• WSS (16:9 / 4:3 Aspect Ratio Auto Switch)

• Channel Type Sorting (Favorite/Sport/Music/News/Movie)

Tuning Options

• FST

• Frequency Search (Optional)

• APS (Auto Search/Name/Sort)

• Auto Search

• CATV/HYPERBAND

Keyboard

• Volume -/ +Button

• Program -/+ Button

• Menu Button

• TV / AV Button

Teletext/OSD

• Simple Text 10 Pages

• Fastext & Top Text (OPT)

• Teletext Languages (ALL)

• Character Based OSD

• OSD Color & Transparency Selection

Electrical features

• 12V 4.16A DC / 100 - 240V AC adapter for 15” TV

• 12V 5.83A DC / 100 - 240V AC adapter for 19” TV

• <1W standby power consumption

System Building Blocks

17MB27 chassis main blocks are as follows:

• Analog Front End : VCTI (Microcontroller+Video Proccessor+Audio Proccessor+IF Demodulator+

Teletext Decoder+ OSD Generator)

• Back End : MST517a-M, MST507a-M (Scaler, Deinterlacer, OSD Generator)

Analog Front End

17MB27 main board consists of two major blocks. The first block is analog front-end and this block is handled by VCTI chip that is highly multifunctional. VCTI performs Tuner IF demodulation, CVBS, RGB, SVHS and audio input selection and processing. The audio processor (MSP) supports equalizer, tone control, volume control, AVL, surround effect etc. The video processor (VSP) handles video processing such as color standard detection and demodulation, picture alignment (brightness, contrast, color etc.). The IC also has a teletext decoder with fastext memory. The processed video output is sent to MST5x7A-M, scaler/deinterlacer in RGB format together with a composite sync.

The TV tuner is PLL controlled symmetrical IF output type. The IF signal is filtered by a single SAW filter. Inter-carrier sound demodulation is performed by the system. After the SAW filter block, IF signal is processed by VCTI IF demodulator. Audio signal is digitally filtered in the IF demodulator block. The same IF signal is buffered and sent to DVB-T module card, tdm1300.

Since VCTI can handle all the audio processing, there is no need for additional audio processor solution on the board. MSP has two audio inputs which are assigned to the Scart in L/R and Audio Switch L/R output. MSP has three audio outputs which are assigned to the headphone amplifier L/R input, audio amplifier L/R input and Audio switch L/R input. The board employs TDA2822M and TDA1308 to drive speaker and headphone outputs, respectively. Switching control for other audio inputs and outputs (HDMI, Back AV, PC, DVD, and DVB-T) is achieved by an I2C controlled audio switch (TEA6422).

Back End

MST5x7A-M has two ADC inputs. First ADC input is assigned to the VCTI RGB output. Other RGB/YPbPr inputs are multiplexed for the second ADC input. HDMI receiver ANX9021 analog output, VGA RGB input and the synchronization signals are multiplexed by a primary RGB switch (PI5V512).

MST5x7A-M has an embedded LVDS transmitter. It can be configured as either single LVDS, or dual LVDS output.

There are three PWM output ports. PWM0 is assigned to analog/digital dimming control for the backlight, PWM1 is used for backlight on/off and panel logic power supply on/off control and PWM2 is used to control PC/HDMI switch IC (PI5V512).

3 POWER CONSUMPTION

The power block diagram with the currents drawn is shown below:

4 MICROCONTROLLER PORT CONFIGURATION

PIN NO

47 P10 MST_RESET

48 P11 TV_RXD I IDTV UART receive signal 49 P12 TV_TXD O IDTV UART transmit signal 50 P13 IRQ O IDTV interrupt request signal 51 P14 KEY I Keyboard function select 52 P15 SC_PIN8 I Scart function select 53 P16 DVD_IR_ON/OFF O DVD infrared signal on/off control 54 P17 POWCON O Standby on/off control

PORT NAME

SIGNAL NAME TYPE FUNCTION

PROTECT

O I

Scaler reset Short circuit detection

PIN NO

PORT NAME

SIGNAL NAME TYPE FUNCTION

55 P20 HDMI_HP_INV O HDMI hot plug signal 56 P21 CS O Switching control for Mstar bus and system I2C 62 Safety VCTI_HS O VCTI composite sync output 78 FBIN DVD_SENSE I DVD module detection 85 Vert+ TV/DVB_SW O IDTV/TV I2C and AGC switch control for tuner 27 P22 WP O Write protection control for NVM 28 P23 IR I Infrared input

Table 4.1 VCTI port configuration

5 SIDE BOARDS & CONNECTORS

5.1 Keyboard

A four-pin connector is used between 17mb27 and the keyboard:

Figure 5.1.1: Keyboard connector

KEY signal is sent directly to microcontroller ADC port and depending on the voltage level of KEY signal, microcontroller performs one of these actions: menu, program+, program-, volume+, volume-, and source.

SOFT_SW signal is used to switch between “power-off” and “standby” modes.

5.2 Infra-red & LED

A five-pin connector is used between 17mb27 and the LED board:

Figure 5.2.1: LED board connector

Pin2 and pin3 carry the control signals for the LED. Pin4 carries the infra-red signal to the microcontroller. Pin5 is used to power up the LED board.

5.3 DVB-T module board

DVB-T module board (tdm1300) is used to receive digital terrestrial broadcast signals. Three cables are used to connect 17mb27 and tdm1300: power, data, and IF.

12V (500mA) is sent to tdm1300 by power cable:

Figure 5.3.1: DVB-T module card power connection on 17mb27

Analog RGB(YPbPr), CVBS, stereo audio, tuner control (SCL, SDA, AGC), and three GPIO port outputs of tdm1300, together with UART ports (TV_RXD, TV_TXD, IRQ) are carried by data cable.

Figure 5.3.2: DVB-T data connector on 17mb27

Tdm1300 board has no tuner on it. Instead, the tuner of 17mb27 is used for both analogue and digital reception. Tuner is controlled by either the 17mb27 microcontroller (VCTI), or tdm1300 board microcontroller. The IF (intermediate frequency) output of the tuner is sent to tdm1300 board for digital reception.

Figure 5.3.3: IDTV IF connector on 17mb27

5.4 DVD module board

DVD module board has two parts: a loader and an electronic card. Electronic card controls the loader and has connections with 17mb27 and DVD keypad.

Three cables are used to connect 17mb27 and DVD electronic card: power, data, and sense.

12V (500mA) is sent to DVD electronic card by power cable:

Figure 5.4.1: DVD module board power connection on 17mb27

Y/C and/or CVBS video, stereo audio outputs and infra-red input of DVD module board is carried on data cable:

Figure 5.4.2: DVD data connector on 17mb27

When a DVD is inserted into the loader, the DVD electronic card sends an interrupt signal (DVD_SENSE) to the 17mb27 microcontroller:

Figure 5.4.3: DVD_SENSE connector on 17mb27

5.5 LVDS connector

MST507A-M is used for single LVDS output and MST517A-M is used for dual LVDS output on 17mb27:

Figure 5.5.1: Single LVDS output connector on 17mb27

Figure 5.5.2: Dual LVDS output connector on 17mb27

Panel_Vcc1 is the power input for the panel LCD module. PIN7 signal is a logic 1 or 0 signal depending

on the panel type.

5.6 Inverter

12V power, backlight on/off control, and dimming control signal are sent to the inverter board:

Figure 5.6.1: Inverter connector on 17mb27

6 IC SPECIFICATIONS

6.1 Microcontoller/Video&Audio Processor (VCT4913G)

VCTI49xy is composed of microcontroller, video proccessor, display and deflection processor, sound proccessor and IF blocks as shown in below figure .

Figure 6.1.1: VCTI49xy block diagram

+ 30 hidden pages