Hitachi kp-hd20a User Manual

HD-SDeye
Thank you for procuring this fine Hitachi Kokusai Electric color camera. Before using the camera, please read this operation manual carefully and keep this manual on file for ready reference in the future.
Full HD HD-SDI Camera
Operation manual
Hitachi Kokusai Electric Inc.
E400359115
Contents
Caution for safe operation
Contents
Introduction ······························· 1
Features ···································· 1
Standard Composition ·················· 1
Name and function························ 2
Connections·································· 3
Lens·············································· 4-5
Setting ··········································6-10
Specifications································ 11
Introduction Features
Hitachi’s camera KP-HD20A is HD-SDI interface one which support Full HD.
High definition
They are high definition and wide viewing angle because
it is full HD.
Low delay HD video signal and long-distance transmission
(at the time of multiunit connection)
High sensitivity
1/3 type high sensitivity MOS sensor has made 0.2lux
high sensitivity.
High functioning
Full HD and double shutter WDR function
1080/30fps double shutter WDS function.
Coaxial superposition
A simple system configuration is possible by one cable
connection.
Standard composition
1) Camera
2) Operation manual
3) Tripod adapter
4) Attchement screw x 3
1
Name and function
Attachment of C mount adapter Attachment of tripod adapter
LENS mount ring
Tripode adaptor installation screw hole
LENS connector [LENS]
Connect the lens cable, when using automatic iris lens. Refer to page 4 (Lens connectors).
C mount adapter (optional accessories)
Lens mount fixing screw
Adjust the flange back Refer to page 4 (Flange back adjustment)
Camera attachment screw hole
Tripod adapter
Back
Status lamp [STATUS]
Camera state is indicated
HD-SDI output modeTurn green light VIDEO output mode Flicked green
light
Power supply input connector Refer to page 3 (Video output
connection).
REMOTE connector [REMOTE]
Refer to page 10 (Remote-contact).
Video output connector [VIDEO]
Refer to page 3 (Video output connection).
Camera menu setting operation switch [MENU]
Various setting and adjustment values are confirmed and changed with these 3 switches. Refer to page 6 to 10 (Setting menu operations).
HD-SDI output connector [SDI]
Refer to page 3 (Video output connection).
2
r
r
SXGA60p
Connections
Example of connection
HD-SDeye color camera KP-HD20A
or
Coaxial superposition
Analog video output for field angle adjustment
DC12V
Coaxial cable
HD-SDI output HD-VLC output
HD-SDI output HD-VLC output
Coaxial cable
Refer to cable length
standard
Coaxial cable
NTSCPAL monito
RGB monito
RGB cable
DVI-D cable
DVI – D moronit
Supported formats XGA 60p SXGA 60p
AC100230V
MU-HD101 back
Supported formats 1080 59.94
1080 50i 1080 29.97p 1080 25p XGA 60p
Cable length standard
HD-SDI mode(1.5Gbps) HD-VLC mode (270Mbps)
5C-FB No power supply
supperposition
* Actual distance changes with cable, connector, temperature, etc, because transmission distance is actual measurement
by sample cables.
* We recommend using cable of 7C-FB or 5C-FB at the time of using HD-SDI mode, because 7C-2V, 5C-2V and 3C-2V
are not guaranteed to support high-frequency signal transmission of HD-SDI mode.
100m 300m
3
A
Lens
Lens selection
1) Dimension A) of lens installation part should be according to the figure below. When the lens with dimention more than the following size is installed, the internal damage of camera may occur.
2) Please do not install a lens which is heavier than the camera body. In case of using such lens, please fix the lens to the installation stand.
Caution
Use of heavy lens may damage the camera because of unbalance.
C mount lensless than 4.1mm CS mount lensless than 4.1mm
Lens
Flange surface of lens
Lens connectors
When a lens-connector-free automatic iris lens is used, the optional lens plug is installed in the lens cable as follows. Please refer the manual for signal and color combination of camera cable.
DCDirect currentcontrol voltage input type lens
Damping coil
Damping coil Driving coil
Video signal input type lens
+12V
Install the head of lens cable to plug and then insert the plug in
the lens connector [LENS] of camera.
Driving coil
Video input
GND
Flange back adjustment
Flange back adjustment is needed after installation of lens or in cases where focus cannot be obtained by normal lens focus operation and focus is lost at the wide angle settings of a zoom lens. In such cases, open the lens iris (refer to page 9) and adjust as follows.
1) Fixed focus lens
Set the lens focus ring to infinity and pickup a camera subject at least 20 meters distant. Loosen the lens mount setscrews (2 screws) and turn the lens and lens mount ring to adjust the focus. After adjusting, tighten the lens mount setscrews.
2) Varifocal and Zoom lens
1) Set the lens to maximum telephoto and pickup a camera subject at least 20 meters distant. Loosen the lens mount setscrews (2 screws) and turn the focus ring to adjust the focus while using care not to turn the lens and lens mount ring.
2) Set the lens to maximum wide angle and pickup the same camera subject. While using care not to turn the lens focus ring, turn the lens and lens mount ring to adjust the focus. Repeat these steps until focus is obtained at both telephoto and wide angle settings. After adjusting, tighten the lens mount setscrews.
The flange back adjustment can adjust C~CS mount range. The angle of view is adjusted by turning the lens zoom ring.
Note
KP-HD20A camera has strucuture that user can change lenses. Therefore dust may adhere to the CCD or the optical filter unit depending on environmental conditions where lens are attached to this camera. If you use this camera under the bright outdoor conditions, dust may be seen depending on the aperture of lens In such cases we recommend that you use AES & LENS mode.
4
Note
If an auto iris lens is used and the object distance is less than few meters, due to focus length of lens, slight blurring can occur at certain iris positions. In such case, please refer to page 9[Lens open setting] and set the lens to full open. At this time, AES is operated.
Auto Electric Shutter (AES)
AES is a function to automatically adjust the electronic shutter speed according to the amount of incident light and keeps the image level constant.
5
Setting
Setup by the operating switch in a back part
MENU buttons
Up(U) Down(D) Right(R) Left(L) button Movement of a cursor
Center (Set) button: Determination of a selection item
Composition of camera setting menu
MAIN MENU [FILE1 ]
SHUTTER :1/30
LIGHT CONT. :-> GAIN :-> WHITE BAL. :-> SUB :-> TITLE :->
LENS :-> SYSTEM :->
SYSTEM MENU
SDI OUTPUT :HD-SDI TV FORMAT :1080p,59.94 VBS ASPECT :16:9
LIGHT CONT. MENU
PEAK/AVE. :0/100 LEVEL : 0
ALC GATE :OFF
WDR MODE :AUTO *WDR BLEND :128 *WDR SHUTTER:1/2000 *WDR LEVEL : 0
WHITE BAL. MENU
MODE :ATW ATW RANGE :NORMAL
*AWB :PUSH R *R GAIN : 0 *B GAIN : 0
GAIN MENU
GAIN MODE :AGC *PRESET GAIN: 0dB AGC LIMIT : 31dB
KNEE
SLOPE1 : 72 SLOPE2 : 24 POINT1 : 48 POINT2 : 80
TV FORMAT
1080i,59.94Hz * 1080i,50 Hz 1080p,29.97Hz * 1080p,25 Hz
Indication is factory
shipment setting.
WHITE GATE :OFF
SUB MENU
CHROMA : 0 DETAIL : 0 PEDESTAL : 0 GAMMA :ON KNEE :ON KNEE S/P :-> MASKING :PREST *HUE/SAT :->
INITIALIZE :PUSH R
TITLE
MODE :OFF TITLE :
MASKING
(HUE) (SAT) R: 150 R: 128 Y: 128 Y: 128 G: 172 G: 128 C: 150 C: 128 B: 120 B: 128 M: 160 M: 128
INITIALIZE :PUSH R
LENS MENU
LENS TYPE :DC IRIS GAIN : 0 LENS OPEN :OFF
L H
6
f
MAIN MENU
1) Press the Set button for at least 2 seconds to display the Main menu on the monitor screen.
……Seting scene files setting
……Shutter speed setting
……Light control menu ……AGC setting menu ……White balance setting menu ……Sub menu ……Camera title setting menu
……Lens setting menu ……Camera tilte setting menu
Main menu
2) Check the current settings at the main menu.
3) Shift the cursor vertically by pushing the Up and Down buttons, then press the Set button to change the setting of the selected item.
4) To return to the normal screen, press the Set button.
5) Changed settings are stored in the camera memory (flash memory) and restore them when the power is switched on.
6) When button operation is not performed for 1 minute during
displaying menu, changed items are saved and menu display disappears.
Scene file setting
Scene file is a function to record various mode settings and the adjusted values of the camera at the file.
1) Press the Set button for at least 2 seconds to display the
main menu on the monitor screen.
2) Use UP and Down buttons to move the cursor to MAIN MENU. push the Right and Left button to change the scene file.
FILE1<->FILE2<-> FILE3<->FILE4<->FILE5<->FILE1
Factory setting is FILE1.
SHUTTER SPEED
1) Shutter speed can be switched at MAIN MENU. Select "SHUTTER" by Up (Down) button. Then shutter speed can be changed by Right/Left button.
[Preset] 1/30(1/25) 1/50 1/100 1/250 1/500 1/1000
1/20001/50001/100001/20000 1/50000
AESAES&LENS(1/1000)AES&LENS(1/2000) AES&LENS(1/5000)
Factory setting is “1/30”.
* AES&LENS is AES priority mode.
7
LIGHT CONT MENU
……Exposure control mode ……Video level adjustment ……Automatic level conrol gate setting
……WDR function setting ……WDR brend ratio setting ……WDR short exposure shutter setting ……WDR short exposure convergence
level setting
Light control menu
Light control menu setting
1) Press the Set button for longer than 2 seconds to display the Main menu.
Select “LIGHT CONTROL” by Up (Down) button. Then LIGHT CONTROL MENU can be displayed by Rght, (1) PEAK/AVE:(PEAK/AVERAGE)
Set the rate of automatic iris PEAK/AVERAGE.
0/100, 15/85, 30/70, 50/50, 75/25, 100/0.
(2)LEVEL:(LEVEL)
Standard level of Automatic exdposure control( AUTO IRIS, AGC, AES ) (dark)-128 to 0 to127(bright)
(3)ALC GATE:(PEAK/AVERAGE
Set PEAK/AVERAGE Automatic level control gate. OFF:Full screen、 Select 1 to 9.
(4) WDR MODE:(Wide dynamic range mode)
Set WDR. OFF/ONmanual/AUTO
(5) WDR BLEND:(WDR short/long exposure ratio
Set WDR short/long exposure ratio.
12850%to 255100%
Effective only at the time of WDR ON
(6) WDR SHUTTTER(WDR short exposure shutter speed)
Set the shutter speed of short exposure at the time of WDR manual mode. Long exposure is set by SHUTTER command.
(7) WDR LEVEL:(Short exposure shutter desired value o AUTO
Short exposure convergence level setting of short exposure shutter automatic control 095%to 255110 % Effective only at the time of WDR Auto mode
GAIN MENU
SUB MENU
……Gain mode setting …… Fixed amplification setting …… Maximum amplification setting
Gain setting
1) Press the Set button for at least 2 seconds to display the main menu on the monitor screen.
2) Select GAIN by Up (Down) button, and display GAIN MENU by Right button. (1)MODESet gain mode.
PRESETPreset gain mode AGCAutomatic gain mode
(2)PRESET GAINSet gain value of manual.
0dB to 48dB
(3) AGC LIMITSet maximum of the automatic gain.
0dB to 48dB B
WHITE BALANCE MENU
……Mode setting ……Range of Following color
temperature setting ……One push setting ……Manual setting(R gain) ……Manual setting (B gain)
……
Auto level conrol gate setting
White balance setting menu
(1) MODESet white balance mode
AT WAutomatic whilte balance.
ManualSet white balance. (2) ATW RANGE Set Range of Following color temperature
NORMAL2500K to 8000K. SPECIAL2500K to 8000K+special light
Sodium lampmercury lamp
(3) AWBOne push automatic white balance
A white balance is adjusted with auto after pressing the right
button. The value of R and G GAIN is updated and it fixes to MANUAL.
(4) R GAINWhite balance hand regulation of R gain
-128 to 0 to 127 This operates, only when a white balance is a manual. (5) B GAIN:White balance hand regulation of B gain
-128 to 0 to 127
This operates, only when a white balance is a manual.
(6) WHITE GATE Set auto level control of white balance.
OFF/ NO.1 to NO.9
……Chroma level setting ……Detail correction setting ……Black level setting ……Gamma correction setting ……KNEE mode setting ……KNEE function setting ……Masking mode setting ……Masking function setting
(1) CHROMAChroma level setting
-128 to 0 to 50 Choroma level is fixed to the value of “-128”, and cannot
be adjusted, at time of B/W MODE.
(2) DETAIL The optimum detail levelseting
-128 to 0 to 127
(3) PEDESTALSet black level.
-28 to 0 to100 (4) GAMMA
(5) KNEE MODE: Mode select OFF : Not use KNEE function ON : Use Knee fnction (6) KNEE: KNEE function setting when KNEE MODE is
SLOPE 1 : KNEE slope 1 0 to 255 SLOPE 2 : KNEE slope 2 0 to 255 POINT 1 : KNEE point 1 0 to 255 (64 = 100%) POINT 2 : KNEE point 1 0 to 255 (64 = 100%)
SLOPE 1
(7) MASKING MODE: Mode select PRESET : Use a standard preset VARIABLE : Use a user setting mode (8) MASKING: Masking function setting when MASKING
(SAT): Degree of saturation of the color R : Red mask setting 1 to 255 Y : Yellow mask setting 1 to 255 G : Green mask setting 1 to 255 C : Cyan mask setting 1 to 255 B : Blue mask setting 1 to 255 M : Magenta mask setting 1 to 255 (HUE): Color phase R : Red mask setting 0 to 255 Y : Yellow mask setting 0 to 255 G : Green mask setting 0 to 255 C : Cyan mask setting 0 to 255 B : Blue mask setting 0 to 255 M : Magenta mask setting 0 to 255
8
Gamma correction setting
ON : Gamma ON HIGH : Gamma ON (High) OFF : Gamma OFF
“ON”.
SLOPE 2
POINT 1 POINT 2
MODE is “VARIABLE”.
R
M
LENS
LENS
Y
(SAT)
(HUE)
LENS TYPE :DC IRIS GAIN : 0 LENS OPEN :OFF
B
……Lens type setting ……Iris gain setting ……Lens open setting
G
(7) INITALIZEInitializing in the factory-shipments state for
the current scene file.
The following message is show after INITIALIZE
command execution.
Push RINITIALIZE command cancel Push DINITIALIZE command execution
TITLE
MODE Set the display position of a camera title OFF: A character is not displayed.
TOPA character is displayed on the upper part of a
screen.
.BOTTOMA character is displayed on the lower part of a
screen.
<TITLE setting>
(1) In the state where a cursor is in TITLE, if the Set button is
pushed, a cursor will move to the setting line of TITLE data, and the 1st character will blink.
(2)
Select the characters by four directions button.
(3)
The character chosen is inputted when the Set button was
pushed. This cursor moves to the following character.
(4)
Once it goes into character setting mode The Set button turn into a character selection button, and the usual menu ON/OFF operation is forbidden.
(5)
If the input of a character is completed, a cursor will be moved to RET by four directions buttons. If the Set buttons are pushed, a cursor will move to TITLE and will return to the usual menu operation.
(6) <-: Character blink of a character setting part moves to the
one character left.
(7) ->: Character blink of a character setting part moves to the
one character left.
(8) DEL : The blinking character eliminate. (9) INS : A space is inserted in the position of the blinking
character.
(10) RET : A cursor is moved to DATA SET.
C
Set data
Character
For edit control
L H
(1) LENS TYPE:DC type or VIDEO type
VIDEO : B/W MODE AUTO does not operate at the time of AGC
OFF and SENSUP OFF / manual..
DC : To which control of the lens of DC input control (position
servo) is attained.
(2) IRIS GAIN Set a control standard level
-128 to 0 to127
(3)LENS OPENA lens is opened wide and AES is turned ON.
OFF Control automatic iris ON Lens open and AES control. At the time of ENS OPEN ON, * is attached to a shutter speed
command and operation becomes improper.
(4) Level indicator
The NAM level meter for ALC
-
Explanation -
When the value of NAM detection is equal to the reference level of ALC, a marker moves to central "+" mark. When it is less than reference level, a marker moves on the left of a center. On the contrary, when it is larger than reference level, a marker moves on the right of a center.
SYSTEM MENU
……SDI output setting ……TV format setting
(1) SDI OUTPUT :Set transmission mode
HD-SDI100 transmission
HD-VLC300 transmission
(2) TV FORMAT (video output)
TV FORMAT function setting.
9
A
TV FORMAT MENU
OperationSelect TV FORMAT by Up (Down) button, and
press Right button.
HD-SDIHD-VLC mode change
Button operation at a camera start-up
(1) Starting in HD-SDI mode
A power supply is started pushing an Up button.
……1080i 59.94Hz ……1080i 50Hz ……1080p 29.97Hz ……1080p 25Hz
(1) 1080i 59.94Hz (NTSC MODEONLY) (2) 1080i 50Hz (PAL MODE ONLY) (3)1080p 29.97Hz (NTSC MODE ONLY) (4)1080p 25Hz (PAL MODE ONLY)
NTSCPAL mode change
PAL mode change
OperationThe following processings are performed at the
time of NTSC mode .
Push left button.5 times) ② Push Down button.
When it pushes except Down button, the change to NTSC mode is canceled. A change in PAL mode is canceled at the time of PAL mode (LED lights up green).
When it is canceled, LED blinks green.
LED is turned on orange after putting out lights of
LED. LED lights up green. (a camera reboots)
A PAL picture is displayed in about ten seconds.
NTSC mode change
OperationThe following processings are performed at the
time of PAL mode.
Push Right button.5 times) ② Push Down button.
When it pushes except Down button, the change to NTSC display mode is canceled. A change in PALmode is canceled at the time of NTSC mode (LED lights up green).
When it is canceled, LED green.
LED is turned on orange after putting out lights of
LED. LED lights up green. (a camera reboots)
A NTSC picture is displayed in about ten seconds
Caution!
Please do not turn off the power by any means during
the change of output mode.
LED lights up red.
LED lights up red.
(2) Starting in HD-VLC mode
A power supply is started pushing a Right button.
Exclusive multiunit MU-HD101 is required for HD-VLC
mode.
Remote-contact operation
n optional remote plug is available to enable remote controlling of the B/W MODE and scene file. The plug is wired as shown in the figure and connected to the remote connector of the camera rear panel.
Remote plug (option)
Scene file setting
Pin No. Signal name
1 N.C. 2 Serial data camera input 3 Serial data camera output 4 GND
Note
1) Nothing should connect with NC pin.
2) Please perform extraction and insertion of a remote plug
after turning off a camera power supply.
D-sub 9 pin (female)
10
Specifications
1) Imaging device 1/3” Progressive Scan MOS
Total pixels 2010(H)x1108(V) 2.2M pixels Effective pixels 1944(H)x1092(V) 2.1M pixels
2) Sync system Internal
3) Video output HD-SDI / Analog CVBS
4) Video format HD-SDI: 1080i 59.94/ 50, 1080P 29.97/ 25 CVBS: NTSC/ PAL
5) Transmission distance HD-SDI Std mode: max100m (5C-FB 75ohm) HD-VLC mode: max 300m (5C-2V 75ohm/ Exclusive multiunit MU-HD101 use)
*mode selectable
6) Minimum illumination Color: 0.2lx(F1.2/AGC48dB)
7) S/N ratio 50dBAGC: OFF/Weight: ON
8) Resolution 800TV line
9) Lens mount C/ CS *C: C mount Adaptor (optional accessory) use
10) Power consumption DC12V or Coaxial superposition from MU-HD101 5.8W
11) Operating temperature -10 to +45 C
12) External dimensions 44(W)x44(H)x59(D)mm
13) Mass Approx.130g
14) Accessory (optional accessory) Lens/Lens plug/Tripod adapter/Power plug/Remote plug/Multiunit (MU-HD101)
15) AGC OFF/ Auto (Max Gain 48dB)/ Manual (0dB to +48dB) *1dB step setting
16) Electronic shutter OFF/ AES/ Manual (1/30(1/25) to 1/50000 sec)
17) BLC OFF/ ON (photometry aria can be set)
18) White Balance Auto: ATW/ AWC Manual: Manual (2500K to 10000K)
19) Wide dynamic range OFF/ON/AUTO
*WDR: Double shutter sampling
20) Picture adjust menu Video level/Gamma correction/Chroma level/Black level/Enhance level
21) Lens control DC/VIDEO
22) Remote control RS-232C
6
12
Loading...