Hitachi KP-FD500GV, KP-F500GV, KP-FD202GV, KP-FD145GV, KP-F145GV Operation Manual
...
CCD camera
KP-FD500GV/F500GV
KP-FD202GV/F202GV
KP-FD145GV/F145GV
KP-FD140GV/F140GV
KP-FD83GV/F83GV
KP-FD33GV/F33GV
Operation Manual
Thank you for producing this fine Hitachi Kokusai Electric CCD camera.
Before using the camera, please read this operation manual carefully and
keep this manual on file for ready reference in the future.
Hitachi Kokusai Electric Inc.
RoHS Compliant
These products compile with the requirement of he RoHS (Restriction of the
use of Certain Hazardous Substances in Electrical and electronic Equipment)
Directive 2002/95/EC.
August 31, 2012 Version 1.11
For R1 or later models
IMPORTANT SAFETY INSTRUCTIONS
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Heed Warnings
All warnings on the product and the operating instructions should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming
pool; and the like.
8. Accessories
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and
serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product.
Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the
manufacturer.
9. Moving
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
10. Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and
these openings must not be blocked or covered.
The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a
built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.
11. Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply
to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to
the operating instructions.
12. Grounding or Polarization
This product is equipped with a three-wire grounding-type plug a plug having a third (grounding) pin. This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the grounding-type plug.
13. Power-Cord Protection
Power-supply cords should be routed to that they are not likely to be walked on or pinched by items placed upon or against them, paying particular
attention to cords at plug, convenience receptacles, and the point where they exit from the product.
14. Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall
outlet. This will prevent damage to the product due to lightning and power-line surges.
15. Overloading
Do not overload wall outlets, extension cords or integral convenience receptacles as this can result in a risk of fire or electric shock.
16. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a
fire or electric shock. Never spill liquid of any kind on the product.
17. Inflammable and Explosive Substance
Avoid using this product where there are gases, and also where there are inflammable and explosive substances in the immediate vicinity.
18. Heavy Shock or Vibration
When carrying this product around, do not subject the product to heavy shock or vibration.
19. Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
20. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
a.When the power-supply cord or plug is damaged.
b.If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to
restore the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance-this indicates a need for service.
21. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock, or other hazards.
22. Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in
proper operating condition.
23. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
24. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce
heat.
A
WICHTIGE SICHERHEITS ANWEISUNGEN
1. Alle Anweisungen lesen
Vor Betrieb des Erzeugnisses sollten alle Sicherheits-und Bedienungsanleitungen gelesen werden.
2. Die Anweisungen aufbewahren
Die Sicherheits-und Bedienungsanleitungen sollten fünftigen Bezug aufbewahrt werden.
3. Warnungen beachten
Die Warnungen auf dem Erzeugnis und in den Bedienungsanleitungen solten beachtet werden.
4. Anweisungen befolgen
Alle Bedienungsanleitung-und Verwendungsanweisungen sollten befolgt werden.
5. Reinigung
Den Stecker des Geräts vor Reinigung aus der Steckdose ziehen. Keine flüssigen Reinigungsmittel oder Aerosolreiniger verwenden. Zum Reinigen
einen feuchten Lappen verwenden.
6. Zubehör
Nur vom-Hersteller des Erzeugnisses empfohlenes Zubehör verwenden, da es sonst zu Störungen kommen kann.
7. Wasser und Feuchtigkeit
Dieses Erzeugnis nicht in der Nähe von Wasser verwenden - z.B, in der Nähe einer Badewanne, eines Waschbeckens, einer Küchenspüle, eines
Waschzubers, in einem nassen Keller, in der Nähe eines Schwimmbeckens usw.
8. Aufstellung
Das Erzeugnis nicht auf einen unstabilen Wagen, Stand, Dreifuß, Träger oder Tisch stellen. Das Erzeugnis kann sonst herunterfallen und ein kind
oder einen Erwachsenen schwer verietzen. Außerdem kann das Gerät schwer beschädigt werden. Nur mit einem Wagen, Stand, Dreifuß, Träger
oder Tisch verwenden, der vom Hersteller empfohlen oder mit dem Erzeugnis verkauft worden ist. Für jegliche Anbringung sollten die Anweisungen
des Herstellers befolgt werden, und das vom Hersteller empfohlene Anbringungszubehör sollte verwendet werden.
9. Eine Kombination von Erzeugnis und Wagen sollte vorsichtig bewegt werden
Schneller Halt, übermäßige Krafteinwirkung und unebene Oberflächen können Umkippen der kombination von Erzeugnis und Wagen verursachen.
10. Ventilation
Schlitze und Öffnungen im Gehäuse dienen der Ventilation. Sie sind für zuverlässigen Betrieb des Gerätes und Schutz vor Überhitzung erforderlich
und dürfen nicht blockiert oder abgedeckt werden. Die Öffnungen sollten niemals dadurch blockiert werden, daß, das Gerät auf ein Bett, ein Sofa, einen
Teppich oder eine ähnliche Oberfläche gestellt wird.
Das Gerät sollte nur dann in Einbauinstallierung wie in einem Bücherschrank oder einem Gestell verwendet werden, wenn angemessene Ventilation
vorgesehen ist bzw. Die Anweisungen des Herstellers befolgt worden sind.
11. Stromversorgung
Dieses Erzeugnis sollte nur an der auf dem Typenschild angegebenen Stromversorgungsart betrieben werden. Wenn Sie nicht sicher sind, was für
eine Stromversorgung Sie haben, so wenden Sie sich bitte an Ihren Erzeugnishändler oder an das lokale Elektrizitätswerk. Beziehen Sie sich für
Batteriebetrieb oder andere Stromquellen vorgesehene Erzeugnisse bitte auf die Bedienungsanleitungen.
12. Erdung oder Polarisierung
Dieses Erzeugnis ist mit einem Schutzkontaktstecker mit drei Leitern ausgerüstet, mit einem Erdungskontakt. Dieser Stecker paßt nur in ein
schuko-Steckdose. Dies ist eine Sicherheitsmaßnahme. Wenn Sie den Stecker nicht in die Steckdose stecken können, so wenden Sie sich bitte
an ihren Elektriker, damit er die veraltete Schuts des Schutzkontaktsteckers unwirksam.
13. Netzkabelschutz
Netzkabel sollten so verlegt werden, deß möglichst nicht darauf getreten wird und daß sie nicht eingeklemmt werden, mit besonderer Beachtung der
kabel an Stackern, Verlängerungskabeln und dem Austritt des Kabels aus dem Erzeugnis.
14. Blitzschlag
Für zusätzlichen Schutz des Erzeugnisses während eines Gewitters oder bei Nichtverwendung für lange Zeit den Stecker aus der Steckdose ziehen.
Dies verhütet Beschädigung durch Blitzschlag und Netzspannungsstöße.
15. Überlastung
Wandsteckdosen, Verlängerungskabel und eingebaute Bequemlickkeitssteckdosen nicht überlasten, da dies Feuer oder elektrischen Schlag
verursachen kann.
16. Eindringen von Fremdkörpern und Flüssigkeit
Niemals Objekte irgendwelcher Art durch die Öffnungen in das Gerät schieben, da diese unter hoher Spannung stehende Teile berühren oder
kurzschließen können, wodurch es zu Feuer oder elektrischem Schlag kommen kann. Niemals Flüssigkeiten irgendwelcher Art auf das Erzeugnis
verschütten.
17. Entflammbare und explosive Substanzen
Vermeiden Sie Verwendung dieses Erzeugnisses an Orten mit Gasen bzw. entflammbaren oder explosiven Substanzen in der direkten Umgebung.
18. Starke stöße oder Vibrationen
Setzen Sie das Erzeugnis beim Transport nicht starken Stößen oder Vibrationen aus.
19. Wartung
Versuchen Sie nicht, dieses Erzeugnis Selbst zu warten, da Sie sich durch Öffnen bzw. Entfernen von Abdeckungen hohen Spannungen und
sonstigen Gefährdungen ausserzen können. Beziehen Sie sich für jegliche Wartung auf qualifiziertes Wartungspersonal.
20. Beschädigung, die Wartung erfordert
Ziehen Sie den Stecker dieses Erzeugnisses aus der Steckdose und wenden Sie sich an qualifiziertes Wartungspersonal, wenn eine der folgenden
Bedingungen vorliegt:
a. Wenn das Netzkabel oder der Stecker beschädigt ist.
b. Bei Eindringen von Flüssigkeit oder Fremdkörpern in das Gerät.
c. Wenn das Erzeugnis Regen oder Wasser ausgesetzt worden ist.
d. Wenn das Erzeugnis bei Befolgen der Bedienungsanleitungen nicht normal funktioniert. Nur die Regelelemente verstellen, die in den
Bedienungsanleitungen behandelt werden, da unangemessene Einstellung anderer Regelelemente Beschädigung verursachen kann und oft
beträchtliche Arbeit durch einen qualifizierten Techniker erfordert, um das Erzeugnis wieder, zu normalem Betrieb zurückzubringen.
e. Wenn das Erzeugnis fallen gelassen oder beschädigt worden ist.
f. Wenn das Erzeugnis eine klare Änderung in der Leistung zeigt-dies weist darauf hin, daß Wartung erforderlich ist.
21. Ersatzteile
Wenn Ersatzteile erforderlich sind, darauf achten, daß der Wartungstechniker nur die vom Hersteller festgelegten Ersatzteile oder Teile mit den
gleichen Charakteristiken wie die ursprünglichen Teile verwendet. Unautorisierte Ersatzteile können Feuer, elektrischen Schlag oder sonstige
Gefährdungen verursachen.
22. Sicherheitsprüfung
Bitten Sie den Wartungstechniker nach der Vollendung von Wartung oder Reparaturarbeiten an diesem Erzeugnis um die Durchführung von
Sicherheitsprüfungen, um zu bestimmen, daß das Erzeugnis im angemissenen Betriebszustand ist
23. Anbringung an der Wand oder an der Decke
Das Erzeugnis sollte nur entsprechend den Empfehlungen des Herstellers an einer Wand oder an der Decke angebracht werden.
24. Wärme
Das Erzeugnis sollte fern von W ärmequellen wie Radiatoren, Heizwiderständen, Öfen und anderen Wärme erzeugenden Erzeugnissen
(einschließlich Verstärkern) aufgestellt werden.
B
MISES EN GARDE IMPORTANTES
1. Lire les instructions
Lire toutes les instructions de sécurité et de fonctionnement avant de faire fonctionner l’appareil.
2. Conserver ces instructions
Conserver les instructions de sécurité et de fonctionnement á des fins de référence ultérieure.
3. Tenir compte des avertissements
Tous les avertissements qui figurent sur l’appareil et dans le mode d’emploi devront être respectés.
4. Observer les instructions
Observer toutes les instructions de fonctionnement et d’utilisation.
5. Nettoyage
Avant de procéder au nettoyage, débrancher l’appareil de la prise secteur. Ne pas utiliser de produits de nettoyage liquides ou en aérosol.
Nettoyer l’appareil avec un chiffon humide.
6. Fixations
Ne pas utiliser de fixations non recommandées par le fabricant de l’appareil car elles pourraient être source de danger.
7. Eau et humidité
Ne pas utiliser l’appareil á proximité d’eau-ar exemple prés d’une baignoire, d’un lavabo, d’un évier ou d’un bac á lessive, dans un sous-sol humide, ou prés
d’une piscine, etc.
8. Accessoires
Ne pas placer l’appareil sur un chariot, un socle, un pied, un support ou one table instables L’appareil pourrait tomber, blessant griévement des
enfants ou des adultes, et étant sérieusement endommagé.
Utiliser exclusivement le chariot, le socle, le pied, le support ou la table recommandés par le fabricant, ou vendus avec l’appareil. Pour tout
montage de l’appareil, respecter les instructions du fabricant, et utiliser á cette fin l’accessoire de montage recommandé par le fabricant.
9. L’appareil monté sur son chariot devra être déplacé avec précaution
Des arrêts brusques, une force excessive et des surfaces irréguliéres pourraient provoquer le renversement de l’ensemble appareil-chariot.
10. Ventilation
Les fentes et les ouvertures du coffret sont prévues pour la ventilation ainsi que pour garantir un fonctionnement en toute sécurité de l’appareil et le
protéger de toute surchauffe, et ces ouvertures ne devront donc être ni obstruées ni recouvertes. Ne jamais obstruer les ouvertures en placant
l’appareilsur un lit, un sofa, un tapis ou toute surface similaire. Ne jamais placer l’appareil dans un support confiné, par exemple une bibliothéque ou
une é tagé re, sans ventilation suffisante ou sans repecter les instructions du fabricant.
11. Sources d’allmentation
L’appareil devra être alimenté exclusivement sur le type d’alimentation indiqué sur l’étiquette signalétique. Sil’on n’est pas sûr du type d’alimentatio
du local, consulter le revendeur de l’appareil ou la compagnie d’électricité locale. Pour les appareils qui fonctionnent sur batterie ou sur d’autres
sources, voir le mode d’emploi.
12. Mise á la terre ou polarisation
L’appareil est doté d’une fiche trifilaire avec mise á la terre, dont la troisiéme broche assure la mise á la terre. Cette fiche ne rentrera que dans les
prises trifilaires de mise á la terre. Ceci est une mesure de sécurité. Si la fiche ne rentre pas dans la prise, faire remplacer la prise désuéte par un
électricien.
Ne pas rendre vaine la measure de sécurité assurée par cette prise avec mise á la terre.
13. Protection du cordon d’alimentation
Acheminer les cordons d’alimentation de facon qu’on ne risque pas de marcher dessus ou de les coincer sous un objet placé dessus ou contre eux.
Faire particuliérement attention aux fiches des cordons, á la proximité des prises, et á l’endroit oú ils ressortent de l’appareil.
14. Foudre
Pour renforcer la protection de l’appareil pendant un orage, ou si l’on s’en éloigne ou qu’on reste longtemps sans l’utiliser, le débrancher de la source
d’alimentation. Ceci permettra d’éviter tout dommage de l’appareil dú á la foudre et aux surtensions de ligne.
15. Surcharge
Ne pas surcharger les prises, rallonges et prises multiples car cela pourrait entraîner un risque de feu ou de choc électrique.
16. Pénétration d’objets et de liquides
Ne jamais enfoncer d’objets d’aucune sorte dans les ouvertures de l’appareil car ils pourraient toucher des points de tension dangereuse ou
court-circuiter des piéces, ce qui pourrait provoquer un feu ou un choc électrique. Ne jamais renverser de liquide d’aucune sorte sur l’appareil.
17. Substances inflammabes et explosives
Eviter d’utiliser l’appareil en présence de gaz, ainsi qu’á proximité immédiate de substances inflammables et explosives.
18. Chocs ou vibrations violents
Lorsqu’on transporte l’appareil, ne pas le soumettre á des chocs ou des vibrations violents.
19. Réparations
Ne pas tenter de réparer l’aapareil soi-même car le fait d’ouvrir ou de retirer les caches risque d’exposer l’utilisateur á des tensions dangereuses
notamment. Confier toute réparation á un personnel qualifié.
20. Dommages nécessitant réparations
Débrancher l’appareil de la source d’alimentation et confier les réparations á un personnel qualifié dans les cas suivants:
a. Lorsque le cordon d’alimentation ou sa fiche sont endommagés
b. Si du liquide s’est renversé sur l’appareil ou que des objets sont tombés dedans
c. Si l’appareil a été exposé á la pluie ou á l’eau.
d. Si l’appareil ne fonctionne pas normalement lorsqu’on observe les instructions d’utilisation.
Ne régler que les commandes couvertes par le mode d’emploi ; en effet, un réglage incorrect des autres commandes pourrait entrainer des
dommages et nécessiteront souvent des travaux de réparation coûteux par un technicien qualifié pour remettre l’appareil en état de marche.
e. Si l’appareil est tombé ou qu’il a été endommagé.
f. Si l’appareil affiche une nette modification de ses performances, cela signifie qu’il a besoin d’être réparé.
21. Piéces de rechange
Si l’on a besoin de piéces de rechange, veiller á ce que le technicien de réparation utilise exclusivement les piéces de rechange spécifiées par le
fabricant ou des piéces ayant les mêmes caractéristiques que les piéces d’origine. Les piéces de rechange non autorisées risquent de provoquer
un feu, un choc électrique et autres dangers.
22. Vérificaton de sécurité
Aprés tout travail d’entretien ou de réparation de l’appareil, demander au technicien de réparation d’effectuer les vérifications de sécurité pour
s’assurer que l’appareil est en bon état de marche.
23.Montage au mur ou au plafond
L’appareil ne pourra être monté au mur ou au plafond que de la maniére recommandée par le fabricant.
24. Chaleur
Eloigner l’appareil des sources de chaleur, telles que radiateurs, appareils de chauffage, cuisiniéres, et de tour produit engendrant de la chaleur (y
compris les amplificateurs).
C
IMPORTANT NOTICE
These products have been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this product in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
WARNING
Changes or modifications not expressly approved by HITACHI KOKUSAI ELECTRIC responsible for compliance
could void the user’s authority to operate the equipment.
These products do not exceed the class A/class B limits for radio noise emissions from digital apparatus as set out in
the radio interference regulations.
Le présent appareil n’émet pas de bruits radioélectriques dépassant les limités applicable aux appareils numériques
de classe A prescrites dans le rVglement sur le brouillage radioélectrique édicter par le ministére des
communications du canada.
For U.S.A.
For Canada
China RoHS
The following statement is related to the regulation on “ Measures for the Administration of the control of Pollution by Electronic
Information Products “ , known as “ China RoHS “.
The table shows contained Hazardous Substances in this camera.
说明书（环境方面：补充资料）
对象产品：CCD 摄像机
１．电子产品污染控制标志
此 标 志 是 根据 2006 年 2 月 28 日公 布 的《 电 子信 息产 品 污染控制 管 理 办 法》 以及
SJ/T11364-2006《电子信息产品污染控制标识要求》而制定的，是用来表示适用于在中华人民
共和国流通的电子信息产品的环保使用期限。
只要遵守此类产品的安全事项以及使用上应注意的问题，从制造日起到此年限内，不会发生
产品中的有害物质外泄、突变等，不会对环境、人体以及财产产生严重影响。同时，此年限是
除去必须定期交换的保守部品的，是其他产品的环保使用期限。
产品在正常情况下使用完毕要废弃时，请遵守各地区对电子信息产品的回收・再利用的相关各项法律、法规。
另外，从第三者处转买的情况下即使在本期限内也视为失去效力。
２．产品中有毒有害物质或元素的名称及含量
部件名称
１ 主机 × ○ ○ ○ ○ ○
○：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
×：表示该有毒有害物质至少在该部件的某一均材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
铅
(Pb)
水银
(Hg)
有毒有害物质或元素
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
D
Note: This product using following equipments satisfies the CE standards.
The shield type camera cable (C-201KSS)
The shield type LAN cable (C5E(S-HFR)(K)-HSL-1: Oki)
Clamp filter (ZCAT 2035-0930A: TDK) at both ends (camera and video processor ends).
E
Note: This product using following equipments satisfies the CE standards.
The shield type camera cable (C-201KSS)
The shield type LAN cable (C5E(S-HFR)(K)-HSL-1: Oki)
Clamp filter (ZCAT 2035-0930A: TDK) at both ends (camera and video processor ends).
F
Note: This product using following equipments satisfies the CE standards.
The shield type camera cable (C-201KSS)
The shield type LAN cable (C5E(S-HFR)(K)-HSL-1: Oki)
Clamp filter (ZCAT 2035-0930A: TDK) at both ends (camera and video processor ends).
G
Note: This product using following equipments satisfies the CE standards.
The shield type camera cable (C-201KSS)
The shield type LAN cable (C5E(S-HFR)(K)-HSL-1: Oki)
Clamp filter (ZCAT 2035-0930A: TDK) at both ends (camera and video processor ends).
H
Note: This product using following equipments satisfies the CE standards.
The shield type camera cable (C-201KSS)
The shield type LAN cable (C5E(S-HFR)(K)-HSL-1: Oki)
Clamp filter (ZCAT 2035-0930A: TDK) at both ends (camera and video processor ends).
I
Note: This product using following equipments satisfies the CE standards.
The shield type camera cable (C-201KSS)
The shield type LAN cable (C5E(S-HFR)(K)-HSL-1: Oki)
Clamp filter (ZCAT 2035-0930A: TDK) at both ends (camera and video processor ends).
J
Phenomena inherent to CCD imaging device
The following phenomena are inherent to a charge coupled device imaging element and do not indicate malfunction.
1) Smear and blooming
Vertical bands are visible when a strong light enters the scene. Adjust the camera aiming direction carefully to avoid strong
direct or reflected light.
2) Fixed pattern noise
High ambient temperature can cause fixed pattern noise to appear throughout the scene.
3) White spot
Imperceptible white spots may rarely come up on the screen due to cosmic rays and so on. It becomes easy to appear when the
sensitivity of the camera is raised in the operation at the high temperature.
4) Moire
Interaction between patterns can produce an additional "phantom" pattern to appear. The CCD picture elements (pixels) are
arranged in a pattern, which can interact with a pattern in the scene (e.g., a performer wearing a finely striped necktie) to result in
a Moire pattern. The effect should be considered when selecting costumes, props and other scene elements.
5) Ghosting
Strong direct or reflected light near an object of interest can cause ghosting of the object to appear in the picture. The effect is
more obtrusive with certain iris settings and lens types. Select the scene layout and camera pointing direction carefully in order
to avoid this effect.
Operating considerations Notes to users
1. Important safety notes
・ Use this camera with a 12VDC power supply,
・ Observe that flammable objects, water or metal do not enter the camera interior. These may lead to failure or accident.
・ Do not modify the camera or use the camera with external covers removed. These may cause failure, void any warranties and pose a
safety hazard.
・ Sop using the camera at the approach of electrical storm (thunder audible). Protect the camera from rain if using it outdoors.
・ In event the camera shows any abnormality, switch off the camera and disconnect the power cord. Contract a Hitachi Denshi service
representative.
2. Handling
・ Do not attempt to remove cover.
・ When installing or removing a lens, be sure to use care that water or dust dose not enter the inside of the camera.
3. Installing and storage
Avoid installing or storing the camera in the following environments.
・ Environments exposed to direct sunlight, rain or snow.
・ Environments where combustible or corrosive gas exists.
・ Excessively warm or cold environment (Operating ambient temperature: -10 to 50℃).
・ Humid or dusty environment.
・ Place subjected to excessive vibration or shock.
・ Environment exposed to strong electric or magnetic field.
・ Do not aim the camera lens at the sun.
・ Do not shoot strong light.
When such a scene is shot, vertical trailing will appear. However, this is not due to failure. In case strong light enters camera through the
lens, partial deterioration in picture quality will result.
4. To obtain stable performance for long time
・ When the camera is used continuously for long time under high ambient temperature, the inside electrical parts become deteriorated,
resulting in shortening its life. To use the camera continuously for long time, the highest temperature must be below 40℃.
5. Connectors
・ Confirm the power is off before connecting or disconnecting a signal cable. Grasp connectors by the body, not the attached wires.
6. Cleaning
・ Use a blower or a lens brush to remove dusts on the lens or the optical filter.
・ Wipe dirt on the case off with dry soft cloth. If dirt are hardened, wipe them off with cloth moistened with neutral detergent liquid; wipe
the cover with dry cloth.
・ Do not use benzene, thinner, alcohol, liquid cleaner or spray-type cleaner.
・ In event dust or other debris is lodged between the CCD and optical filter, consult dealer for cleaning by an optical technician.
7. Attention about laser light
・ Laser light may do damage to CCD.
・ When you use laser light, be careful to irradiate it on the CCD surface.
・ The CCD breakage by laser light irradiation is out of warranty. (The repair is not free of charge.)
K
Table of Contents
1. Overview ········································································································································································································ 1
2. Standard Composition ············································································································································································· 1
3. Features ········································································································································································································· 1
4. Section name and functions ································································································································································ 2
5. Camera mounting ······················································································································································································· 2
6. Lens ················································································································································································································· 2
7. Optical filter ································································································································································································· 3
8. Connector ····································································································································································································· 4
9. System example ························································································································································································· 5
10. Functions and operations ······································································································································································ 7
11. Frame rate ···································································································································································································· 28
12. Packet size and Packet delay ····························································································································································· 33
13. Trigger mode ································································································································································································ 34
14. Digital output ······························································································································································································· 37
15. Trigger operation and timing chart ··················································································································································· 38
16. Input /Output signal ················································································································································································· 44
17. Photo coupler delay ················································································································································································· 44
18. Output sequence of RAW data ··························································································································································· 45
19. Spectral response ····················································································································································································· 47
20. Specifications ······························································································································································································ 53
21. Dimensions ··································································································································································································· 57
L
Overview
Molded type
Shield type
2m C-201KSM
C-
201KSS
5m C-
501KSM
C-
501KSS
10m C-102KSM
C-
102KSS
KP-FD500GV/FD202GV/F145GV/FD140GV/FD83GV/FD33GV are Gigabit Ethernet output type color camera which utilized
the progressive scan CCD image sensor with square pixel which adopted the RGB primary color mosaic filter. KP-F500GV
/F202GV/F145GV/F140GV/F83GV/F33GV are black and white type. KP-FD145GV and KP-F145GV have sensitivity in the
near-infrared region.
Since these cameras are Power over Ethernet (PoE) type, power supply is input via LAN cable.
Standard composition
Check when unpacking
Camera (with IR cut filter / Dummy glass） ·································· 1
Composition table ·················································································· 1
Optional accessories
(1) 12 pin plug HR10A-10P-12S(01)
(2) Junction box JU-F30/JC-100
(3) Dummy glass (AR coated) ARC1214
(4) IR cut filter IRC650
(5) Tripod adaptor TA-M1
(6) LAN cable (CAT5E or CAT6)
In the CE Marking region, use a high flexibility shielded cable
(recommended C5E(S-HFR)(K)-HSL-1: Oki). Refer to page 6.
(7) Camera cable
In the CE Marking region, use the shield type and attach clamp
filter (ZCAT 2035-0930A: TDK) at both ends (camera and
video processor ends). Refer to page 6.
Note: When not using the specified junction box, LAN cable,
camera cable and clamp filter, malfunctions may be caused.
Features
・High resolution
The 2/3-inch 5.00 million pixels (KP-FD500GV/F500GV), the 1/1.8-inch 2.02 million pixels (KP-FD202GV/F202GV), the
2/3-inch 1.45 million pixels (KP-FD145GV/F145GV), the 1/2-inch 1.45 million pixels (KP-FD140GV/F140GV), the 1/3-inch
0.8 million pixels (KP-FD83GV/F83GV) and the 1/3- inch 0.33 million pixels (KP-FD33GV/F33GV) square lattices CCD
achieve a high resolution.
・Gigabit Ethernet
By adoption of Gigabit Ethernet interface, high-speed connection of maximum of 1 Gbps can be possible. Moreover, by using
hub or switcher, construction of multiple camera system can be easily performed.
It is also possible to 100m.
・GigE VisionTM correspondence
Based on Industrial camera interface standard GigE Vision, a maximum of 1Gbps high speed data transmit is available and
suitable for image processing.
・GENiCAMTM correspondence
Development of camera control system is easy because industrial camera control API "GENiCAM" lead EMVA (European
Machine Vision Association).
・High color fidelity
RGB primary color mosaic filter and 6 color independent achieve a high resolution and high color fidelity.
・Power over type Ethernet
Power supply can be input via Ethernet cable.
GENiCAMTM is a trademark of EMVA (European Machine Vision Association). Ethernet is a trademark of XEROX Corporation.
GigE VisionTM and the distinctive logo are trademarks of AIA (Automated Imaging Association).
1
Section name and functions
Camera / Tripod adaptor
Lens mount
Camera / Tripod adaptor
mounting screw holes
（C mount）
mounting screw holes
Ethernet connector
Use for digital video output and
camera control signal input/
output signal.
DC IN/SYNC connector
Use for DC+12V power or external
ＲＡ Ｔ ＥＤ
ＳＥ Ｒ ． ＮＯ ．
Ｐ ＬＡ Ｔ Ｅ
trigger /VD signal input.
Camera mounting
Attached optional accessory the tripod adaptor "TA-M1", mount the camera to a tripod or mounting bracket.
L
Screw type: Ｕ1/4-20
Length Ｌ = 4 to 5.5mm
Screws longer than 5.5 mm can cause internal damage, while less
than 4 mm prevents secure fastening and risks dropping to cause
damage and injury.
Lens
CAUTION
Observe the dimensions of the lens mounting selection as
illustrated at the right.
If the dimensions are not observed, do not use such a lens,
because the lens and the camera will be damaged.
Lens optics
Lens flange
Max 6.5mm
2
Optical filter
1
2
3 4
How to remove the IR cut filter / Dummy glass (*).
(1) Remove two screws ① and filter holder ② will come off.
(2) Remove the IR cut filter / Dummy glass ③ from filter frame ④.
(3) Then, reinstall and secure filter holder ② with two screws ①.
Note: Prior to removing the optical filter, be sure to turn off the power. Since garbage etc. invades into image reception surface
camera, please work under the clean air, such as a CLEAN ROOM.
* IR cut filter is equipped in the KP-FD500GV/FD202GV/FD145GV/FD140GV/FD83GV/FD33GV.
Dummy glass is equipped in the KP-F500GV/F202GV/F145GV/F140GV/F83GV/F33GV.
3
Connector
LED 1
LED 2
1. Ethernet connector
PIN NO.
1 TRP1+
2 TRP13 TRP2+
4 TRP3+
5 TRP36 TRP27 TRP4+
8 TRP4-
Status LED 1 LED 2
Immediately after Power ON Green Light On Orange Light On
1Gb Transmission Green Light On Orange Blink On
100Mb Transmission Red Light On Orange Blink On
2. DCIN/SYNC connector
PIN NO.
1 GND (+12V) 7 TRIG-A / VD (H)
2 +12V 8 TRIG-B (C)
3 GND 9 TRIG-B (H)
4 N.C. 10 FLASH / VD OUT
5 GND 11 N.C.
6 N.C. 12 TRIG-A / VD (C)
Connector (matching camera: SNH-10-12(RPCB) SANWOO or equivalent
Plug (matching cable plug: HR10A-10P-12S(01) HIROSE or equivalent
In the CE Marking region, use the shield type and attach clamp filter (ZCAT 2035-0930A: TDK) at both ends (camera
and video processor ends). Refer to page 6 for details.
Please do not connect 1 pin and 3/5 pin when using PoE. When connecting it, PoE may stop the power supply.
Because TRIG-A/VD and TRIG-B are photo coupler input, 8/12 pin is isolated with 1/3/5 pin. When 8/12 pin is
connected to GND, please connect to 3 pin or 5 pin.
(Note) Please do not unplug and insert cable (digital out cable) with a power supplied to a camera.
Please do not input any single to N.C. pin because .the camera may break down.
Signal
Signal PIN NO.
Signal
3
11
10
1
2
9
8
12
4
6
5
7
4
System example
KP-FD500GV/F500GV/FD202GV/F202GV/FD145GV/F145GV/FD140GV/F140GV/FD83GV/F83GV/FD33GV/F33GV connect
to PC sing LAN cable.
HIT ACH I
Camera
Camera cable
LAN cable
(CAT5E/CAT6)
JU-F30
HIT ACH I
LAN cable
(CAT5E/CAT6)
Camera
PoE hub
(*) Note that following point when connecting the camera
(1) Please connect the camera to device for Gigabit Ethernet (1000BASE-T).
Please set the imaging size according to following formula when the camera is connected to 100BASE network.
(Image Width) x (Image Height) x (Data bit) ≦ 20000000 ･･･ KP-FD500GV
≦ 18750000 ･･･ KP-F500GV
≦ 16000000 ･･･ KP-FD202GV/F202GV
Any Image size is OK ･･･ Models except the above
(2) Please use LAN cable of CAT5E or more (recommendation: CAT6 straight cable).
(3) To the NIC for Jumbo frame is recommended to be used
Recommended NIC: Intel Pro1000 PT Desktop
(4) When the camera is connected to Laptop PC, please use the one whose built-in LAN is Gigabit Ethernet
(1000BASE-T) correspondence.
The external LAN card (CardBus32 or USB2.0) may not display the cameras ability because of the bus limitation.
ExpressCard is corresponded on the standard but useable product is unconfirmed (.as of April, 2008).
(5) Please connect the camera and PC by 1 to 1 as much as possible
Please use the device corresponded to Jumbo frame when using the switching hub etc.
(6) Please confirm if the camera and the connected LAN port have same subnet.
Example-1: Same subnet --> Controllable
IP address Subnet mask Subnet
Camera 192.168.1.100 255.255.255.0 192.168.1.0/24
LAN port 192.168.1.1 255.255.255.0 192.168.1.0/24
Example-2: Different subnet --> Uncontrollable
IP address Subnet mask Subnet
Camera 192.168.1.100 255.255.255.0 192.168.1.0/24
LAN port 192.168.2.1 255.255.255.0 192.168.2.0/24
(7) A striped noise might be caused according to the equipment (hub etc.) connected with the camera.
In that case, please connect the cable to another port of the equipment again.
(8) Please disable UAC (User Account Control) when using WindowsVista.
Please set UAC to "Never notify" when using Windows7.
+12V
PC with NIC
for Gigabit
5
(C-201KSS)
(8) In the CE Marking region, use following specified cables and clamp filters
Camera cable
HIT ACH I
Camera
(C5E(S-HFR)(K)-HSL-1: Oki)
LAN cable
(ZCAT 2035-0930A: TDK)
Clamp filter
Camera cable / LAN cable
Approx. 100 to 150 mm
(Same applies to LAN cable)
Ferrite core
Plastic case
6
Functions and operations
START
Various mode setup and adjustment of KP-FD500GV/F500GV/FD202GV/F202GV/FD145GV/F145GV/FD140GV/F140GV
/FD83GV/F83GV/FD33GV/F33GV are performed by the remote control via Gigabit Ethernet. Operation and adjustment way
of function utilized are described below.
Each command is classified into following 5 types:
・ Enumeration : Command dealing with enumeration-type parameter
・ Integer : Command dealing with integer-type parameter
・ Float : Command dealing with float-type parameter
・ Command : Executable format command
・ String : Command dealing with string
"Standard" means the function based on GENiCAMTM Standard Feature Naming Convention (SFNC) and "Custom" means the
original function. The function with description of "related to SELECTOR" is affected to change of SELECTOR value.
The software for GENiCAMTM can operate by using command name. Moreover, it can also be operated by reading /writing the
value to address directly.
1. Commands for acquisition (1) ACQUITION ： Setting for image acquisition method
・MODE ： Select of mode
Command name ： AcquitionMode (Enumeration / Standard)
Address ： A0030000 h
Values (Factory setting 1) ： 1 "Continuous" Frames are captured continuously until stopped with the STOP command.
2 "MultiFrame" The number of frames specified by FRAME COUNT is captured.
3 "SingleFrame" One frame is captured.
・START ： Acquisition start
Command name ： AcquiationStart (Command / Standard)
Address ： A0030004 h
Values (write only) ： 1 Start the acquisition of the camera image.
・STOP ： Acquisition stop
Command name ： AcquitionStop (Command / Standard)
Address ： A0030008 h
Values (write only) ： 0 Stop the acquisition of he camera image.
・EXTRA MODE ： Special one shot *using when MODE is SingleFrame
Command name ： AcquitionModeExtra (Enumeration / Custom)
Address ： A0F30018 h
Values (Factory setting 0) ： 0 "Off" The camera releases the shutter according to internal synchronization.
1 "On" The camera releases the shutter when START command is received.
Exposure
(Internal sync)
Data output
Data output timing when EXTRA MODE is Off
Exposure
START command
Data output
Data output timing when EXTRA MODE is On
7
・FRAME COUNT ： Set the number of capture *using when MODE is MultiFrame
Command name ： AcquitionFrameCount (Integer / Standard)
Address ： A003000C h
Values (Factory setting 1) ： 1 to 255 Set the number of frames to be acquired in MultiFrame mode.
・FRAMERATE RAW ： Acquisition frame rate
Command name ： AcquitionFrameRateRaw (Integer / Standard)
Address ： A0030014 h
Values (Factory setting 36: KP-FD500GV
63: KP-F500GV
251: KP-FD202GV
265: KP-F202GV
245: KP-FD145GV/FD140GV
261: KP-F145GV/F140GV
297: KP-FD83GV
313: KP-F83GV
384: KP-FD33GV
403: KP-F33GV
： 1 to 36 : KP-FD500GV
7 to 63: KP-F500GV
7 to 251: KP-FD202GV
7 to 265: KP-F202GV
7 to 245: KP-FD145GV/FD140GV
7 to 261: KP-F145GV/F140GV
7 to 297: KP-FD83GV
7 to 313: KP-F83GV
7 to 384: KP-FD33GV
7 to 403: KP-F33GV Control the Frame rate in 1 fps step.
* Refer to page 28 "Frame rate"
・CURRENT FRAMERATE ： Current actually frame rate
Command name ： CurrentFrameRateRaw (Integer / Custom)
Address ： A0F30104 h
Values (read only) ： 1 to 9 : KP-FD500GV
7 to 63: KP-F500GV
7 to 251: KP-FD202GV
7 to 265: KP-F202GV
7 to 245: KP-FD145GV/FD140GV
7 to 261: KP-F145GV/F140GV
7 to 297: KP-FD83GV
7 to 313: KP-F83GV
7 to 384: KP-FD33GV
7 to 403: KP-F33GV
It is frame rate that camera actually drives.
* Refer to page 28 "Frame rate"
8
2. Commands for acquisition image (1) WIDTH MAX ： Maximum width of the image
Command name ： WidthMax (Integer / Standard)
Address ： A002F008 h
Values (read only) ： 2448: KP-FD500GV/F500GV
1620: KP-FD202GV/F202GV
1360: KP- FD145GV/F145GV/FD140GV/F140GV
1024: KP-FD83GV/F83GV
656: KP-FD33GV/F33GV
(2) HEIGHT MAX ： Maximum height of the image
Command name ： HeightMax (Integer / Standard)
Address ： A002F00C h
Values (read only) ： 2050: KP-FD500GV/F500GV
1220: KP-FD202GV/F202GV
1024: KP- FD145GV/F145GV/FD140GV/F140GV
768: KP-FD83GV/F83GV
492: KP-FD33GV/F33GV
(3) WIDTH ： Set the actual image width
Command name ： Width (Integer / Standard)
Address ： A0020000 h
Values (Factory setting 2448: KP-FD500GV/F500GV
1620: KP-FD202GV/F202GV
1280: KP-FD145GV/FD140GV
1360: KP-F145GV/F140GV
1024: KP-FD83GV/F83GV
652: KP-FD33GV/F33GV)
： 2 to WIDTH MAX Set the actual image width at intervals of 2 pixels.
(4) HEIGHT ： Set the actual image height
Command name ： Height (Integer / Standard)
Address ： A0020004 h
Values (Factory setting 2050: KP-FD500GV/F500GV
1220: KP-FD202V/F202GV
960: KP-FD145GV/FD140GV
1024: KP-F145GV/F140GV
768: KP-FD83GV/F83GV
490: KP-FD33GV/F33GV)
： 2 to HEIGHT MAX Set the actual image height at intervals of 2 pixels.
(5) OFFSET ： Setting of start position of the actual image
・OFFSET X ： Set the horizontal offset
Command name ： OffsetX (Integer / Standard)
Address ： A0020008 h
Values (Factory setting 0) ： 0 to (WIDTH MAX - WIDTH - 2)
Set the horizontal start position of the actual image at intervals of
2 pixels.
・OFFSET Y ： Set the vertical offset
Command name ： OffsetY (Integer / Standard)
Address ： A002000C h
Values (Factory setting 0) ： 0 to (HEIGHT MAX - HEIGHT - 2)
Set the vertical start position of the actual image at intervals of
2 pixels.
9
Loading...