2 1 3 4
2 1
3
A
1. General
The KP-FD202GV is single CCD type RGB color camera which utilized the progressive scan CCD
image sensor with square pixel for SXGA format of 1/1.8-inch which adopted the RGB primal color
mosaic filter. By adoption of Gigabit Ethernet interface, high-speed connection of maximum of 1
B
C
D
Gbps can be possible. Moreover, by using hub or switcher, construction of multiple camera system
can be easily performed.
2. Outstanding features
(1) High resolution and color fidelity
The 1/1.8-inch 2,010,000 pixels square lattice progressive scan CCD and the RGB primary
color mosaic filter achieve a high resolution and high color fidelity of 1620(H) x 1220(V) (UXGA).
(2) Gigabit Ethernet interface
High-speed serial interface Gigabit Ethernet is supported and direct connection is possible to
PC by the diameter cable of thin as compared with parallel output. It is possible to 100m.
(3) GigE Vision (Ver. 1.00) correspondence
Based on Industrial camera interface standard GigE Vision, a maximum of 1Gbps high speed
data transmit is available and suitable for image processing.
(4) GENiCAM (Ver. 1.00) correspondence
Development of camera control system is easy because industrial camera control API
"GENiCAM" lead EMVA (European Machine Vision Association).
(5) PoE correspondence
Power supply can be input via Ethernet cable (Power over Ethernet).
(6) Remote control
- Multi-step electronic shutter (from 1/30 to 1/50000 second in 8 steps)
- Variable shutter (from 10 to 1/100000 second)
- The image capture at desired timing using the external trigger signal
- White balance (ATW, Manual and One-push)
- 6 color independent masking (R, G, B, Cy, Mg, Ye can be independently varied)
and other various functions are set by remote control via a Gigabit Ethernet cable.
Gigabit Ethernet
Progressive scan CCD color camera
KP-FD202GV
Specifications (Preliminary) Ver.1.00
A
B
C
D
0 0
1
E
F
9
E
-
SYMBOL DATE DESCRIPTION
MODEL KP-FD202GV
DESIGNED DATE
F
CHECKED DATE
May.31,2008
APPROVED DATE
STORED DATE
(first edition)
TOLERANCE
UNIT
SCALE
Prod. Code - Order No.
TITLE
KP-FD202GV
Specifications
DWG.
No.
D F 0 2 2 - 4 P E - T 1
(DRAWN) DESIGNED
REV.
SHEET
4
2 1 3 4
2 1
3
3. Specifications
(1) Imaging device 1/1.8-inch progressive scan interline CCD
A
(2) Scanning area 7.16 mm (H) x 5.44 mm (V)
(3) Scanning system Progressive
(4) Aspect ratio 4 : 3
(5) Frame rate 18 frames per second (full pixel readout RGB 8bit)
B
C
D
E
(6) Sync system Internal / external
(7) Lens mount C mount
(8) Flange focal distance 17.526 mm
(9) Video output
(10) Sensitivity 2000lx, F5.6, 3200K
(11) Minimum illumination 10 lx (F1.4 GAIN MAX)
(12) Electric shutter OFF / Auto (AES) / Manual (PRESET or VARIABLE)
OFF is normal exposure (frame rate)
1/10000, 1/50000 second.
Total pixels 1688 (H) x 1248 (V)
Effective pixels 1628 (H) x 1236 (V)
Pixel size 4.4 um (H) x 4.4 um (V) (square lattice)
Color filter RGB primary color mosaic filter
Interface Gigabit Ethernet
Protocol GigE Vision compliant
Transfer 1 Gbit per second
Image format RGB 8/10/12bit YUV(4:2:2) 8/10/12bit
RAW 8/10/12bit Mono 8/10/12bit
Maximum image size 1620 (H) x 1220 (V)
Frame rate 30 frame per second
*Frame rate is different for following format
RGB 8bit: 18 frame per second
RGB 10bit: 12 frame per second
RGB 12bit: 9 frame per second
YUV 8bit: 28 frame per second
YUV 10bit: 24 frame per second
YUV 12bit: 24 frame per second
RAW 10bit: 28 frame per second
RAW 12bit: 28 frame per second
RAW 10bit: 28 frame per second
RAW 12bit: 28 frame per second
PRESET 1/30, 1/60, 1/100, 1/250, 1/1000, 1/2000,
VARIABLE 10 to 1/100000 second
A
B
C
D
E
F
DWG.
No.
D F 0 2 2 - 4 P E - S 1
4
SHEET
2
F
9
2 1 3 4
A
2 1
3
B
C
D
E
(13) External trigger shutter
Mode Fixed shutter
One trigger
VD Sync
Reset control
Input Via Gigabit Ethernet cable (Software trigger)
12-pin connector (Hardware trigger)
Input level 24Vp-p +/- 1V
Threshold 3.7V +/- 0.5V (Low --> High)
3.3V +/- 0.5V (High --> Low)
Input polarity High / Low adjustable
Input delay Adjustable
(14) External sync signal
VD output 5Vp-p +/- 0.3V
Strobe out 5Vp-p +/- 0.3V
Output polarity High / Low adjustable
Strobe delay Adjustable
Strobe duration Adjustable
(15) Partial scan Selectable start position and width of picture grabbing in 2H step.
(16) ALC (Auto level control) Adjustable for video level
(17) White balance ATW / MANUAL / One-push
(18) Gain Auto / Manual (0dB to 18db) (Approx. 0.0358dB step)
(19) Gamma OFF (γ=1) / ON
(20) Color masking OFF / ON (6 vector independent masking)
(21) Paint black Adjustable
(22) Sharpness Adjustable
(23) Black level Adjustable
(24) Knee Adjustable
(25) Power supply voltage DC+12V +/- 1V (input from 12-pin connector)
48V (PoE)
(26) Current consumption Approx. 5.0W (DC+12V)
(27) Ambient
Performance 0 to +40℃ (+32 to +104 F), less than 90 % RH
Operation -10 to +50℃ (+14 to 122 F), less than 90 % RH
Storage -20 to +60℃ (-4 to 140 F), less than 70 % RH (without dew condensation)
(28) Vibration endurance 10 to 55 Hz (2.37 to 71.7 m/s2), sweep: 1 min XYZ 30min
(29) Shock endurance 490.3 m/s2 (Drop test, once each top, bottom, left and right)
(30) External dimensions 44(W) x 29(H) x 72(D) mm (not including protrusions)
(31) Mass Approx. 140g
A
B
C
D
E
F
DWG.
No.
D F 0 2 2 - 4 P E - S 1
4
SHEET
3
F
9
2 1 3 4
2 1
3
4. Composition
(1) Camera (with IR cut filter)
A
(2) CD-ROM (Operation manual, Control software and SDK)
(3) Composition table
5. Optional accessories
(1) Dummy glass (AR coated) ARC1214
(2) IR cut filter IRC650
(3) Junction box JU-F30,
B
C
D
(4) Tripod adaptor TA-M1
(5) 12pin plug HR10A-10P-12S(01)
(6) Camera cable
Molded type Shield type
2 m C-201KSM C-201KSS
5 m C-501KSM C-501KSS
10 m C-102KSM C-102KSS
In the CE Marking region, use the shield type and install clamp filter
（ZCAT2035-0930A: TDK） at both ends of the cable.
(7) LAN cable (Commercial item) CAT5E Straight cable
CAT5E Cross cable
CAT6 Straight cable
CAT6 Cross cable
A
B
C
D
E
F
DWG.
No.
D F 0 2 2 - 4 P E - S 1
4
SHEET
4
E
F
9
2 1 3 4
2 1
3
6. Specification of Digital output connector
A
B
C
D
E
F
(1) Gigabit Ethernet connector
PIN NO.
Signal
LED1 LED2
1 TRP1+
2 TPR13 TRP2+
4 TPR3+
5 TRP36 TRP27 TRP4+
8 TRP4-
Connector: RJ-45
*LED Status
STATUS LED1(Green) LED2 (Yellow)
Power ON Light Off Light On
Transmission Blink On Light On
Transmission pause Light Off Light On
(2) 12-pin connector
PIN NO.
Signal PIN NO.
Signal
1 GND (+12V) 7 TRIG-A / VD (H)
2 +12V 8 TRIG-B (C)
3 GND 9 TRIG-B (H)
4 AUX 10 FLASH / VD OUT
5 GND 11 N.C.
6 N.C. 12 TRIG-A / VD (C)
Connector (camera side) : SAMWOO SNH-10-12 (RPCB) or equivalent
Plug (matching cable plug) : Hirose HR10A-10P-12S (01) or equivalent
Please do not unplug and insert cable (camera cable) with a power supplied to a camera.
Install clamp filter (ZCAT 2035-0930A: TDK) at both ends (camera and video processor
ends) in the CE marking legion.
Please do not connect 1 pin and 3/5 pin when using PoE. When connecting it, PoE may stop
the power supply. Because TRIG-A/VD and TRIG-B are photo coupler input, 8/12 pin is
isolated with 1/3/5 pin. When 8/12 pin is connected to GND, please connect to 3 pin or 5 pin.
Note: Please do not input any signal to N.C. pin because machine may break down.
A
B
C
D
E
F
DWG.
No.
D F 0 2 2 - 4 P E - S 1
4
SHEET
5
9
2 1 3 4
2 1
3
Pixel
Line
B
G
8. Output sequence when format is RAW
A
B
C
1 2
1
R
G R G
2
G B
・
・
・
1219
R G R G
G B G B
1220
・・・
1619 1620
G B
A
B
C
9. Spectral response
D
1
0.9
0.8
0.7
0.6
0.5
0.4
E
Relative Response
0.3
0.2
0.1
0
400 450 500 550 600 650 700
R
D
IR cut filter
E
Wave Length (nm)
F
DWG.
No.
F
SHEET
D F 0 2 2 - 4 P E - S 1
4
6
9
2 1 3 4
2 1
3
10. External view
A
A
ＤＣ ＩＮ/ＳＹＮＣ
Ｅｔｈｅｒｎｅｔ
B
C
D
１３
ＭＡＮＵＥＬ
ＡＰＥＲＣＥＶＯＩＲ
ＳＥＥ ＭＡＮＵＡＬ
６６.０８.７
ＣＯＬＯＲ：ＢＬＡＣＫ
７７.２
７２.０
５.２
６６.０８.７
４－Ｍ２（ＤＥＰＴＨ：３.５）
２５
２１.２
ＣＯＬＯＲ：ＢＬＡＣＫ ＣＯＬＯＲ：ＢＬＡＣＫ
ＣＯＬＯＲ：ＢＬＡＣＫ
・ＭＡＳＳ： ＡＰＰＲＯＸ １４０ ｇ
・ＴＯＬＥＲＡＮＣＥ： ±０.５
B
・ＵＮＩＴ： ｍｍ
・ＳＣＡＬＥ： ＮＴＳ
C
ＳＥＲ．Ｎ Ｏ．
ＰＬＡＴＥ ＲＡＴＥＤ
D
Ｕ１
２６（φ２７.４）
２５
２６
２９
DWG.
No.
１４.５
E
４－Ｍ３（ＤＥＰＴＨ：３.５）
F
SHEET
D F 0 2 2 - 4 P E - S 1
4
7
9
E
４－Ｍ３（ＤＥＰＴＨ：３.５）
４４ （６.３）
F
2 1 3 4
A
2 1
3
This product complies with the requirement of the RoHS(Restriction of
e use of Certain Hazardous Substances in Electrical and Electronic
itachi Kokusai certifies this product complies with the standard
warranty conditions of Hitachi Kokusai, and that quality control is
B
Notice:
These specifications are subject to change without prior notice due to
product improvement.
Confirm the most recent specifications at time of order.
H
implemented to the extent required to comply with these conditions.
RoHS Compliant
th
Equipment) Directive 2002/95/EC
A
B
C
D
E
Warranty and service:
(1) The guarantee period is one year after the data purchase.
However, the defects due to erroneous use or intentional act are excluded.
(2) As the defect after expiration of the guarantee period, where product repair is
possible, repair will be performed at charge.
(3) The present Warranty pertains only to the camera unit. Secondary malfunctions
attributable to camera failure as well as expenses incurred by disassembly and
reassembly of the related system, are beyond the scope of this Warranty.
(4) Compensation for loss of business, loss or damage to software, database and other
contingent losses are beyond the scope of this Warranty.
(5) Hitachi Kokusai Electric Inc. is not liable for the losses caused when the equipment
is used in a system, use for business trades, production process, medical fields,
crime prevention applications, etc.
(6) In the case of camera trouble by miss wiring of cable, it will be considered as out of
warranty.
C
D
E
F
DWG.
No.
D F 0 2 2 - 4 P E - S 1
F
SHEET
8
9
4
2 1 3 4
2 1
3
Modification history
A
SIMBLE
B
C
DATE CORRECTION AND REASONS DESIGNED
A
B
C
D
E
D
E
F
DWG.
No.
D F 0 2 2 - 4 P E - S 1
4
SHEET
9
F
9
Loading...