CCD Camera
KP-DE500
KP-E500
Operation manual
Before using the camera, please read this operation manual
carefully and keep this manual on file for ready reference in
the future.
Hitachi Kokusai Electric Inc.
Table of contents
CAUTION FOR SAFE OPERATION…………... A
IMPORTANT NOTICE…………………………... K
General……………………………………………. 1
Features………………………………………….. 1
Operating considerations……………………... 2
Phenomena inherent to CCD image device... 3
Section names and functions………………… 4
Connections……………………………………... 6
Lens………………………………………………... 7
Recommended lenses………………………… 7
Note on lens selection…………………………. 8
Installation of CS-mount lens…………………. 8
Lens selector switch…………………………… 9
Flange back adjustment………………………. 10
Camera mounting……………………………….. 11
Setting menu description…………………….. 12
Setting menu composition…………………… 12
Menu operations………………………………. 13
Main Menu……………………………………... 13
Camera Title Menu……………………………. 14
Light Control Menu……………………………. 16
AGC setting……………………………………. 19
Shutter Speed setting…...……………………. 21
Sensitivity enhance setting…………………... 22
Raising sensitivity by color-B/W selection….. 23
White Balance Menu...……………………….. 25
Sub Menu……………………………………… 29
Remote menu operation………………………. 32
Specifications…………………………………… 33
Accessories……………………………………... 34
Supplied accessories…………………………. 34
Optional accessories…………………………. 34
General
The KP-DE500 is an ultra high sensitivity color camera
that utilizes the electron multiplication type CCD
(EM-CCD) image sensor.
The KP-E500 is an ultra high sensitivity camera that
utilizes the electron multiplication type CCD (EM-CCD)
image sensor.
Features
Ultra high sensitivity
Ultra high sensitivity is possible due to the electron
multiplication (EM) CCD which multiplies the charge on
the individual pixels before the charge is converted to a
voltage, eliminating noise that would be associated with
amplification gain. Moving images retain the clarity and
sharpness even under low light conditions.
High color fidelity
An RGB primary color mosaic filter is used to produce
images of high vertical resolution and color fidelity.
New digital signal processor (DSP)
A new Digital Signal Processor (DSP) with improved
luminance signal processing and a 5 H enhancer is used
to obtain high quality images with a high signal to noise
(S/N) ratio.
Various functions
・Auto tracking white balance (ATW)
・Color / Black & White select
・
Digital noise reduction (DNR)
・Electric shutter speed
・Electric sensitivity enhance
・Backlight compensation (BLC)
・Text display (character generator)
1
Operating considerations
Power supply
Be sure to use the power source specified in the Major
Specifications.
・Before plugging or unplugging a connector, be sure
to turn off power.
To plug or unplug a connector, be sure to hold the
connector section.
・Note that it will take several seconds until a picture is
displayed on the monitor after power on.
Handling
・Do not attempt to remove cover.
・When installing or removing a lens, be sure to use
care that water or dust does not enter the inside of.
the camera.
Installing and storage
Avoid installing or storing the camera in the following
environments.
・Environments exposed to direct sunlight, rain or snow
・Environments where combustible or corrosive gas
exists
・Excessively warm or cold environment (Operating
ambient temperature: -10 to 50℃)
・Humid or dusty environment
・Place subjected to excessive vibration or shock
・Environment exposed to strong electric or magnetic field
・Do not aim the camera lens at the sun.
・Do not shoot strong light or a scene including strong light.
When such a scene is shot, vertical trailings will appear.
However, this is not due to failure.
In case strong Tight enters the camera through the lens,
partial deterioration in picture quality will result.
To obtain stable performance for long time
When the camera is used continuously for long time
under high ambient temperature, the inside electrical
parts become deteriorated, resulting in shortening its life.
To use the camera continuously for long time, the
highest temperature must be below 40℃.
Cleaning
・Use a blower or a lens brush to remove dusts on the
lens or the optical filter.
・Wipe dirts on the case off with dry soft cloth. lf dirks
are hardened, wipe them off with cloth moistened
with neutral detergent liquid; wipe the cover with dry cloth.
・Do not use benzine,thinner,alcohol,liquid cleaner or
spray-type cleaner.
・In event dust or other debris is lodged between the CCD
and optical filter, consult dealer for cleaning by an optical
technician.
2
Phenomena inherent to CCD imaging device
Following are the phenomena inherent to a CCD imaging device, and not defects
1) Smear and blooming
When strong light (lamp, fluorescent lamp, and
reflected light, etc.) is shot, a blue belt to remain thinly
in vertical and the horizontal direction of light might go
out.
Moreover, the lower side on the monitor screen might
become pure-white momentarily.
In this case, change the angle of the camera so that
such strong light does not enter the camera through
the lens.
2) Fixed pattern noise
When the camera is operated in a high temperature,
fixed pattern noise may appear on the entire screen.
3) Moire
When fine patterns are shot, moire may be displayed.
4) Burning
When excessively intense light comes to the CCD for a
long time, the spectral filter in the CCD pixel may be
deteriorated, and the color of the corresponding portion
may change.
Avoid using the camera under such condition.
3
Section names and functions
Tripod adaptor holes
See camera mounting
on page 11.
Lens mount screws
See page 10.
Lens mount ring
See flange back adjustment
on page 8.
Lens connector［LENS］
Connect lens cable when
using an auto iris lens. See
page 9.
C-mount adaptor
See installation of CS-mount
lens on page 8.
Camera mounting hole
See page 11.
4
Remote connector
［REMOTE］
Use for remote menu
operations.See page 32.
DC input connector
See page 6.
Set up buttons［SETUP］
Use when setting up and adjusting
the camera with reference to the
screen menu. See page 13.
Lens select switch［LENS］
Set according to the type of
lens. See page 9.
Video output connector［VIDEO］
See connections on page 6.
5
Connections
Video output connection
Connect the video output of the camera to the video input of a
monitor or other equipment. When using a “loop through”
connection of two or the more monitors, set the 75Ω switch of
only the final monitor to ON.
Determine the type of cable according to the distance of the
connected equipment. The maximum cable lengths indicated
below are recommended for avoiding appreciable picture
degradation.
3C-2V ・・・・ 150m
5C-2V ・・・・ 200m
7C-2V ・・・・ 300m
10C-2V ・・・・ 400m
KP-DE500
KP-E500
Monitor 1
Monitor 2
Monitor 3
Set the 75Ω switch of only the final monitor to on.
Set the 75Ω switch of other monitors to off.
75-ohm coaxial cable
External power supply connection
Use a stabilized 12 VDC(±10%) power supply rated at 2.5
ampere or greater. Wire the accessory 3-pin DC plug as
shown in the figure for connecting the power supply to the
camera.
Caution
Be sure to confirm proper polarity before switching
on power.
DC input connector
6
Lens
Recommended lenses
Use an auto iris lens having a plug pin arrangement conforming to EIAJ (Electronic Industries Association of Japan)
specifications.
This camera is using a CCD that has sensitivity in infrared region ( from 700 to 1000nm ).
Please select a lens for use from the following recommendation lens table.
12VG412ASIR 4.0～12.0 ｍｍ F1.2～360 C-mount
12VG1040ASIR 10.0～40.0 ｍｍ F1.4～360 C-mount
DV5× 3.6R4B-SA2 3.6～18.0 ｍｍ F1.8～360 CS-mount
Type Lens model Specification Lens mount Lens switch
Auto iris 1/2
HG3Z4512FCS-IR 4.5～12.5 ｍｍ F1.2～360 CS-mount
NOTE
If another type of lens is used, it may detract from camera performance or there may be difficulty is attaching the lens.
When procuring, be sure to specify the EIAJ compatible plug.
DC
7
A
Note on lens selection
1) Observe the maximum size limit (A in the figure)
When installing the lens. Internal damage can occur
If a larger lens is used.
2) Avoid using a lens that is heavier than the camera.
If unavoidable, be sure to fix the lens itself on a support.
Caution
A heavy lens can disturb the balance with respect to
The camera and possibly result in damage.
C-mount lens: Less than 4.1mm
CS-mount lens: Less than 4.1mm
Lens
Lens flange surface
Installation of CS-mount lens
C-mount adaptor is provided for the camera in the factory.
When using a CS-mount lens, unscrew and remove the
C-mount adaptor. Save the C-mount adaptor for possible future.
8
A
Lens selector switch
Set the switch according to the type of auto-iris lens.
The factory setting is DC.
DC ：Set to DC when using a lens having a DC
Control voltage input.
VIDEO ：Set to VIDEO when using a lens having a
Video signal input.
NOTE
1) To the extent possible, set the lens response to
Average. Hunting can occur toward the Peak setting.
2) When adjusting the level, choose a location with
adequate brightness (more than 300 lux) where the
AGC and Sens Up functions are not needed.
Lens connector
When using an auto iris lens, install the lens plug on the lens
Cable as indicated in the figures. Refer to the lens instructions
Regarding the signals and wire colors.
DC type lens
Video type lens
fter installing the plug on the cable, connect it to the lens
connector on the rear of the camera.
Damping coil －
Damping coil ＋ Drive coil －
Video input
+12V
GND
Drive coil ＋
Flangeback adjustment
Flangeback adjustment is needed in cases where focus cannot
be obtained by normal lens focus operation or focus is lost at the
maximum telephoto and wide angle settings of a zoom lens.
In such cases, open the lens iris and adjust as follows.
Fixed focus lens
1) Set the lens focus ring to infinity.
2) Aim toward an object at least 20 meters distant.
3) Loosen the (2) lens mount screws and turn the lens mount
ring to adjust the focus. Use care not to disturb the lens
focus ring.
4) Tighten the lens mount screws.
NOTE
If using an auto iris lens and the adjustment object distance
is less than several meters, due to lens depth of focus
relationship, slight blurring can occur at certain iris positions.
In this event, darken the scene so as to open the iris and
adjust the focus or flangeback to prevent the blurring.
9
Zoom lens
1) Set the lens to telephoto and aim toward an object at least
20 meters distant.
2) Turn the lens focus ring to adjust the focus.
3) Set the lens to wide angle. Loosen the (2) lens mount
screws and turn the lens mount ring to adjust the focus.
Use care not to disturb the lens focus ring.
4) Again set to telephoto but adjust the focus by turning the
Lens focus ring.
5) Repeat these steps and carefully adjust for best focus.
6) Finally, tighten the lens mount screws.
10
(pag
)
Camera mounting
If the camera is to be suspended from the ceiling,
change the position of the tripod adaptor from the
bottom to the top of the camera, as indicated in the figure.
Tripod adaptor
Binding head screws M3 x 8
Caution:
Use the following type of camera mounting screw.
Type :U 1/4-20
Length:L=7mm
If longer than 7 mm, there is risk of internal damage to
the camera. Conversely, if too short, the camera will not
be firmly secured and there is risk of dropping.
11
Setting menu description
The camera setting and adjustments can be changed to conform to conditions of use. Use the setting menu indicated on the monitor
screen to check and change the settings and adjustments. The setting menu is comprised as follows.
Setting menu composition
Main Menu
(page 13 )
Camera Title Menu
e 14
・Display character setting
・Display position setting
Light Control Menu (page 16 )
AGC Menu (page 19 )
Shutter Speed setting (page 21 )
Sensitivity enhance setting (page 22)
Color-B/W selection (page 23 ) (*)
・Light control mode setting
・Video level adjustment, etc.
・AGC mode setting
・Fixed and limit gain setting
・WB mode setting
・WB detection area setting
・Manual R/B gain adjustments, etc
12
White Balance Menu (page 25 ) (*)
Sub Menu (page 29 )
(*) Note: Only KP-DE500
・Gamma
・Chroma gain adjustment
・Black reference level adjustment
・Detail adjustment
・Polarity
・Digital noise reduction
・Burst signal
・Camera reset
Menu operations
Three rear panel setup buttons are used to shift the cursor and
select items from the menus.
③
① Up button : Shift the cursor in the upward direction or
increase an adjustment value.
② Down button : Shift the cursor in the downward direction
or decrease an adjustment value.
③ Set button : Press to display the main menu or to
change a setting.
Note:
lf no button is pressed, the menu display extinguishes
automatically after about 5 minutes.
①
②
Main Menu
1) Press the SET button for at least 2 seconds to display
the main menu on the monitor screen.
◆◆ ＭＡＩＮ ＭＥＮＵ ◆◆
>ＣＡＭＥＲＡ ＴＩＴＬＥ ：ＯＦＦ ↵
ＬＩＧＨＴ ＣＯＮＴＲＯＬ：ＯＦＦ ↵
ＡＧＣ ：ＯＮ
ＳＨＵＴＴＥＲ ＳＰＥＥＤ：ＯＦＦ
ＳＥＮＳ ＵＰ ：ＯＦＦ
Ｂ／Ｗ ＭＯＤＥ ：ＯＦＦ
ＷＨＩＴＥ ＢＡＬＡＮＣＥ：ＡＴＷ
ＳＵＢ ＭＥＮＵ
ＥＮＤ
↵
↵
2)
Check the present settings at the main menu.
MAIN MENU
3) Shift the cursor vertically by pressing the UP and DOWN
buttons, then press the SET button to enable changing the
setting of the selected item.
4) If changes are unnecessary, shift the cursor to “END” and
Press the SET button to return to the normal screen.
5) When an item indicated by a
the SET button shifts to the next menu.
…… Camera title setting menu
…… Light control setting menu
…… AGC setting menu
…… Shutter speed setting
…… Sensitivity enhance Setting
…… B/W mode setting (*)
…… White balance mode setting menu (*)
↵
…… Sub menu
…… End of menu display
(*) Note: KP-E500 is not displayed.
↵ mark is selected, pressing
Camera Title Menu
One line of up to 22 alphanumeric characters can be displayed
on the screen. The display on/off and position are selected at the
camera title menu.
1) Press the SET button for longer than 2 seconds to display
the main menu.
2) Use the UP and DOWN buttons to shift the cursor to
“CAMERA TITLE”, then press the SET button to display the
camera title menu.
3) While the cursor is at “MODE”, press the SET button to shift
the mode in the sequence “OFF”, “TOP”, “BOTTOM”.
OFF : Characters not displayed. (Factory setting)
TOP : Characters displayed at top of screen.
BOTTOM : Characters displayed at bottom of screen.
◆ ＣＡＭＥＲＡ ＴＩＴＬＥ ＭＥＮＵ ◆
>ＭＯＤＥ ：ＯＦＦ
ＲＥＴ
ＥＮＤ
CAMERA TITLE MENU (MODE: OFF)
14
…… Display On/OFF and position
( OFF / TOP / BOTTOM )
…… Return to the main menu
…… End of menu display
Display character input
1) When the mode is Top or Bottom, the characters indicated in
the figure can be used.
◆ ＣＡＭＥＲＡ ＴＩＴＬＥ ＭＥＮＵ ◆
>ＭＯＤＥ ：ＴＯＰ
０１２３４５６７８９
ＡＢＣＤＥＦＧＨＩＪＫＬＭ
ＮＯＰＱＲＳＴＵＶＷＸＹＺ
！？＃＆（ ）、 ．：；～＊％
＋－ｘ／＝“‘
ＳＰＡＣＥ ← → ＲＥＳＥＴ
ＰＯＳＩＴＩＯＮ ＲＥＴ ＥＮＤ
ＣＡＭＥＲＡ ＮＯ．１・・・・・・・・・・・
CAMERA TITLE MENU (MODE: TOP or BOTTOM)
…… Display On/OFF and position
( OFF / TOP / BOTTOM )
Input character select table
…… Blank, cursor shift (left / right), character delete
…… Display position, return, end
…… Input character display
2) Press the DOWN button, then use the UP and DOWN
buttons to shift the flashing cursor sequentially among the
usable characters.
3) When the SET button is pressed, the selected character is
entered in sequence beginning with the left-most of 22 dots
shown at the bottom of the screen.
Afterwards, each newly selected character is entered
sequentially toward the right.
The item under character input selecting department uses it in
the following manner.
SPACE : To add a blank space, shift the flashing cursor to
“SPACE”, then press the SET button.
13
←・→ : The input characters can be edited by using the
1) Set the flashing cursor to either of the arrow symbols and
Press SET button. The flashing cursor shifts in the arrow
direction. Press the SET button repeatedly to where the
flashing cursor overlaps the character to be changed.
2) Select the character to be inserted with the UP and DOWN
buttons, then press SET to change the character.
RESET : To delete all characters from the display, shift the
RET : Position the flashing cursor to “RET” and press SET
END : Shift the cursor to “END” and press the SET button to
Title positioning setting POSITION
Use when the display position on the screen has been
determined.
1) Shift the flashing cursor to Position and press SET to open
the title position screen indicated in the figure. Screen top
and bottom positions are determined respectively by
“MODE” settings “TOP” and “BOTTOM”.
arrow symbols.
flashing cursor to “RESET”, then press SET. After
deleting, the flashing cursor returns to the start of
the input character select table.
to exit the “CAMERA TITLE MENU” and return to
the “MAIN MENU”.
close the menu and return to the normal screen.
2) Press the UP and DOWN buttons to shift the characters
horizontally. Afterwards, press SET to confirm the display
position and return to the main menu.
UP button DOWN button
ＣＡＭＥＲＡ ＮＯ．１
Title positioning screen (Top)
…… Character position (Top)
…… Character position (Bottom)
15
Light Control Menu
Light control mode setting
1) Press the SET button for longer than 2 seconds to display
the main menu.
2) Use the UP and DOWN buttons to shift the cursor to
“LIGHT CONTROL”, then press the SET button to display
the light control menu.
3) While the cursor is at “MODE”, press the SET button to shift
the mode in the sequence “AVERAGE”, “BLC”, “PEAK/AVE”.
AVERAGE : Responds to the average lighting over a
broad area. (Factory setting)
BLC : Exposure is controlled only by the
luminosity level of specific area.
(Scanning area is selectable from 9 area.)
PEAK/AVE : The peak level and the average level are
used together and exposure is controlled.
(The ratio of a peak value and average
value is changeable.)
16
◆ ＬＩＧＨＴ ＣＯＮＴＲＯＬ ＭＥＮＵ ◆
>ＭＯＤＥ ：ＡＶＥＲＡＧＥ
ＬＥＶＥＬ ： ０００
ＲＥＴ
ＥＮＤ
…… Select light control mode
…… Video level adjust (-128～000～+127)
…… Return to the main menu
…… End of menu display
LIGHT CONTROL MENU (MODE: AVERAGE)
Video level adjustment
The optimum video level is set at the factory (factory setting is
“000”). If necessary, the level can be changed as foIIows.
1) Use the UP and DOWN buttons to shift the cursor to
“LEVEL”, then press the SET button. The adjustment value
at the right of Level flashes.
2) Change the video level by pressing the UP and DOWN
buttons. (Variable range: -128～000～+127)
3) Return the factory setting(000) by simultaneously pressing
the UP and DOWN buttons for two seconds.
4) Press the SET button to confirm the setting and the cursor
migrates to “RET”.
Note
For video level adjustment on lenses that use the video
signal type lens iris, please refer to the user's manual
of the lens.
r
NOTE
The video level adjustment for lenses that use a video
signal type lens, is adjusted using the binding screws on
the side of the lens as shown in the method below.
1) The lens side sensitivity binding adjustment gauge is
displayed on the light control menu, when the LENS
SW on the camera back is set to [VIDEO].
◆ ＬＩＧＨＴ ＣＯＮＴＲＯＬ ＭＥＮＵ ◆
>ＭＯＤＥ ：ＡＶＥＲＡＧＥ
Ｌｅｖ
|||||||||||||||||||||||||||||||||||||||||||||||･･
･････････････････････
Ｒｅｆ
||||||||||||||||||||||||||||||||||||||||||||||･･･
････････････････････
ＬＥＶＥＬ ： ０００
LIGHT CONTROL MENU (MODE: AVERAGE)
…… Select light control mode
…… Video output level gauge
…… Control reference level gauge
…… Video level adjust (-128～000～+127)
…… Return to the main menu
…… End of menu display
2) Please do the sensitivity binding on the side of the
Lens so that the value of video output level gauge
[Lev] does not drop from the value of reference level
gauge [Ref].
3) When the value of [Lev] is adjusted to a lower value
than the value of [Ref] the repetition phenomenon
(hunting) of the lens iris may occur along automatic
gain control in the camera.
Setting of BLC
In the case where there is a strong light source and sunlight in
the background, the lens iris will close according to the scene
brightness, causing the desired object in the scene to appea
dark. This mode is used under such a condition.
4) Press the SET button for longer than 2 seconds to display
the main menu.
5) Use the UP and DOWN buttons to shift the cursor to
“LIGHT CONTROL”, then press the SET button to display
the light control menu.
6) The following menu is displayed. Push the SET button
to select “BLC”, when the cursor is in “MODE”.
◆ ＬＩＧＨＴ ＣＯＮＴＲＯＬ ＭＥＮＵ ◆
>ＭＯＤＥ ：ＢＬＣ
ＡＲＥＡ ＳＥＬＥＣＴ：ＮＯ．１
ＬＥＶＥＬ ： ０００
ＲＥＴ
ＥＮＤ
↵
…… Select light control mode
…… Go to area select menu and selected area No.
…… Video level adjust (-128～000～+127)
…… Return to the main menu
…… End of menu display
LIGHT CONTROL MENU (MODE: BLC)
7) Shift the cursor to “AREA SELECT” and push the SET
button to display the detection area(BLC) select menu.
17
ＡＲＥＡ（ＢＬＣ）
ＮＯ．１
┃ ┃
┃ ┃
┗━━━━━━┛
DETECTTION AREA (BLC) SELECT MENU
┏━━━━━━┓
5) There are 9 light detect areas selected by the UP and
DOWN buttons. Select the areas from nos. 1 to 9 that
include the subject of main interest. (Factory setting is NO.1)
UP button : 1→2→3→4→5→6→7→8→9
(ascending order)
DOWN button : 9→8→7→6→5→4→3→2→1
(descending order)
6) After deciding the detection area, push the SET button to
return to the light control menu.
Detect area position
6 5
2
1 3
7
8 9
4
Setting of PEAK/AVERAGE
When there is strong spot light in the background a halo may
appear and cause obstruction to a desired object in the image.
This mode is used under such a condition.
1) Press the SET button for longer than 2 seconds to display
the main menu.
2) Use the UP and DOWN buttons to shift the cursor to
“LIGHT CONTROL”, then press the SET button to display
the light control menu.
3) The following menu is displayed, push the SET button
and change to “PEAK/AVE”, when the cursor is in “MODE”.
◆ ＬＩＧＨＴ ＣＯＮＴＲＯＬ ＭＥＮＵ ◆
ＭＯＤＥ ：ＰＥＡＫ／ＡＶＥ
>ＰＫ／ＡＶ ： １５／ ８５
ＬＥＶＥＬ ： ０００
ＲＥＴ
ＥＮＤ
…… Select light control mode
…… Select peak / average value ratio
…… Video level adjust (-128～000～+127)
…… Return to the main menu
…… End of menu display
LIGHT CONTROL MENU (MODE: PEAK/AVE)
18
4) Shift the cursor to “PK/AV” and push the SET button, peak /
average ratio value changes. As the peak value is enlarged
It reacts to spot light. Factory setting is “15/85”.
SET button : 15/ 85→30/ 70→50/ 50→75/ 25→100/ 0
NOTE
As the peak value increases the hunting phenomenon
of the lens reacting to the video level may cause
flickering resulting in changes of brightness in the
image.
AGC Menu
Setting AGC mode
1) Press the SET button for longer than 2 seconds to display
the “MAIN MENU”.
2) Use the UP and DOWN buttons to shift the cursor to “AGC”,
then press the SET button to display the “AGC MENU”.
◆ ＡＧＣ ＭＥＮＵ ◆
>ＭＯＤＥ ：ＯＮ
ＡＧＣ ＬＩＭＩＴ ：２５０
ＲＥＴ
ＥＮＤ
AGC MENU (MODE: ON)
3) While the cursor is at “MODE”, press the SET button to shift
the mode in the sequence “ON”, “OFF”.
ON : The video output level is controlled automatically to a
proper value within the range of “AGC LIMIT”
according to brightness. (Factory setting)
OFF : “FIX. GAIN” mode that does not change, according
to light level.
…… Select AGC mode
…… Limit gain (155～250)
…… Return to the main menu
…… End of menu display
Setting AGC LIMIT (AGC ON)
1) Use the UP and DOWN buttons to shift the cursor to
“AGC LIMIT”, then press the SET button. The adjustment
value at the right of value flashes.
2) Change the “AGC LIMIT” by pressing the UP and DOWN
buttons. (Variable range: 155～250)
3) Return to the factory setting(250) by simultaneously pressing
the UP and DOWN buttons for two seconds.
4) Press the SET button to confirm the setting and the cursor
shifts to “RET”.
Setting FIX. GAIN (AGC OFF)
◆ ＡＧＣ ＭＥＮＵ ◆
ＭＯＤＥ ：ＯＦＦ
>ＦＩＸ． ＧＡＩＮ ：０００
ＲＥＴ
ＥＮＤ
AGC MENU (MODE: OFF)
…… Select AGC mode
…… Fix. Gain (000～250)
…… Return to the main menu
…… End of menu display
19
2) Change the “FIX. GAIN” by pressing the UP and DOWN
buttons. (Variable range: 000～250)
3) Return to the factory setting(000) by simultaneously pressing
the UP and DOWN buttons for two seconds.
4) Press the SET button to confirm the setting and the cursor
shifts to “RET”.
NOTE
The noise in the image may be conspicuous when high
levels of amplification are used.
1) Use the UP and DOWN buttons to shift the cursor to
“FIX. GAIN”, then press the SET button. The adjustment
value at the right of value flashes.
20
Shutter Speed setting
1) Press the SET button for longer than 2 seconds to display
the “MAIN MENU”.
2) Use the UP and DOWN buttons to shift the cursor to
“SHUTTER SPEED” ; the shutter speed setting flashes.
3) Press the SET button to select the speed sequentially in the
following order.
SET button:
OFF(1/60)→1/100→1/250→1/500→1/1000→1/2000→AES
The factory setting is OFF (1/60 second).
◆◆ ＭＡＩＮ ＭＥＮＵ ◆◆
>ＣＡＭＥＲＡ ＴＩＴＬＥ ：ＯＦＦ ↵
ＬＩＧＨＴ ＣＯＮＴＲＯＬ：ＯＦＦ ↵
ＡＧＣ ：ＯＮ
ＳＨＵＴＴＥＲ ＳＰＥＥＤ：ＯＦＦ
ＳＥＮＳ ＵＰ ：ＯＦＦ
Ｂ／Ｗ ＭＯＤＥ ：ＯＦＦ
ＷＨＩＴＥ ＢＡＬＡＮＣＥ：ＡＴＷ
ＳＵＢ ＭＥＮＵ
ＥＮＤ
↵
MAIN MENU
↵
↵
…… Camera title setting menu
…… Light control setting menu
…… AGC setting menu
…… Shutter speed setting
…… Sensitivity enhance Setting
…… B/W mode setting (*)
…… White balance mode setting menu (*)
…… Sub menu
…… End of menu display
(*) Note: KP-E500 is not displayed.
Auto electronic shutter (AES)
This function adjusts the light amount using only the CCD
shutter. Use this function with a fixed iris lens.
NOTE
1) lf using a DC type lens, fix the iris at fully open.
2) The AES function cannot be set with a video signal
type lens.
3) In the following types of cases, use a different shutter
speed. Strong light enters the scene, such as from a
spotlight or window.
・Strong smear or blooming occurs in the scene.
・Screen flicker or coloration occurs.
Sensitivity enhance setting (SENS UP)
The present camera includes a sensitivity enhancement function
that increases the CCD exposure time and interpolates the image
with an image stored in memory to effectively boost the sensitivity.
1) Press the SET button for longer than 2 seconds to display
the “MAIN MENU”.
◆◆ ＭＡＩＮ ＭＥＮＵ ◆◆
>ＣＡＭＥＲＡ ＴＩＴＬＥ ：ＯＦＦ ↵
ＬＩＧＨＴ ＣＯＮＴＲＯＬ：ＯＦＦ ↵
ＡＧＣ ：ＯＮ
ＳＨＵＴＴＥＲ ＳＰＥＥＤ：ＯＦＦ
ＳＥＮＳ ＵＰ ：ＯＦＦ
Ｂ／Ｗ ＭＯＤＥ ：ＯＦＦ
ＷＨＩＴＥ ＢＡＬＡＮＣＥ：ＡＴＷ
ＳＵＢ ＭＥＮＵ
ＥＮＤ
↵
MAIN MENU
↵
↵
…… Camera title setting menu
…… Light control setting menu
…… AGC setting menu
…… Shutter speed setting
…… Sensitivity enhance Setting
…… B/W mode setting (*)
…… White balance mode setting menu (*)
…… Sub menu
…… End of menu display
(*) Note: KP-E500 is not displayed.
2) Use the UP and DOWN buttons to shift the cursor to
“SENS UP” ; the setting flashes.
3) Press the SET button to select the setting sequentially in the
following order.
SET button: OFF→AUTO x2→AUTO x4→AUTO x6→
AUTO x8→AUTO x10→AUTO x12→AUTO x16→
AUTO x32→AUTO x64→OFF→MANU x2→MANU x4
→MANU x6→MAN x8→MANU x10→MANU x12→
MANU x16→MANU x32→MANU x64→MANU x88→
MANU x128
22
OFF : Sensitivity enhance function not used; factory setting.
AUTO : As the scene darkens, the sensitivity is automatically
enhanced by the selected multiple. Best mode for
day/night continuous surveillance.
MANU : Mode for fixed sensitivity boost. When AGC is ON,
fixed at maximum gain.
The setting state of SENS UP and SHUTTER SPEED
SHUTTER
SPEED
1/60 OFF OFF OFF
1/100 1/100
1/125
|
1/2000
AES AES AES
1/2000
SENS UP setting
OFF AUTO MANU
1/100
→OFF
1/125
|
→OFF
→OFF →OFF
1) When SENS UP setting is Manual, the shutter speed setting
is ineffective (off).
2) At SENS UP Auto, the shutter speed setting is as follows.
･ Shutter speed is 1/100 or effective during AES.
･ Shutter speed is 1/100 and ineffective (off) in modes other
AES.
21
NOTE
1) Enhanced sensitivity can cause blurring of moving
images.
2) In the following types of cases, reduce the sensitivity
multiple.
・ Noise increases at high sensitivity and further
increases at high frequency.
・ The Shutter speed cannot be changed during
Auto and Manual SENS UP settings. Temporarily
set SENS UP to OFF when changing the Shutter
speed.
・ White flaws may become apparent at high
sensitivity, but these are not due to malfunction.
Raising sensitivity by color-B/W selection
[Only KP-DE500 type]
1) Press the SET button for longer than 2 seconds to display
the “MAIN MENU”.
◆◆ ＭＡＩＮ ＭＥＮＵ ◆◆
>ＣＡＭＥＲＡ ＴＩＴＬＥ ：ＯＦＦ ↵
ＬＩＧＨＴ ＣＯＮＴＲＯＬ：ＯＦＦ ↵
ＡＧＣ ：ＯＮ
ＳＨＵＴＴＥＲ ＳＰＥＥＤ：ＯＦＦ
ＳＥＮＳ ＵＰ ：ＯＦＦ
Ｂ／Ｗ ＭＯＤＥ ：ＯＦＦ
ＷＨＩＴＥ ＢＡＬＡＮＣＥ：ＡＴＷ
ＳＵＢ ＭＥＮＵ
ＥＮＤ
↵
↵
MAIN MENU
2) Use the UP and DOWN buttons to shift the cursor to
“B/W MODE” ; the setting flashes.
3) Press the SET button to select the setting sequentially in
the following order.
SET button: OFF→ON→AUTO(H)→AUTO(M)→AUTO(L)
OFF : Color always mode; factory setting.
ON : B/W always mode
…… Camera title setting menu
…… Light control setting menu
…… AGC setting menu
…… Shutter speed setting
…… Sensitivity enhance Setting
…… B/W mode setting (*)
…… White balance mode setting menu (*)
↵
…… Sub menu
…… End of menu display
(*) Note: KP-E500 is not displayed.
AUTO : Changes to the color image and B/W image
About B/W mode
The camera CCD responds to infrared light (From 700nm
to 1000nm) that is invisible to the human eye.
The normal color mode uses an IR cut filter to remove the
infrared component.
Sensitivity is usually more important in the B/W mode.
Therefore, the IR cut filter is removed to take advantage of
sensitivity in the infrared region.
automatically according to brightness.
1) The character of the rest of “AUTO” is showing
the brightness (the image level) where the mode
changes from color to a B/W image.
AUTO(H) : About 70% or less of proper levels
AUTO(M) : About 50% or less of proper levels
AUTO(L) : About 30% or less of proper levels
2) Change is using the scale factor data of the
amplification data or SENS UP of automatic gain
control for the color image from a B/W image.
AGC setting is “OFF” or SENS UP setting is
“OFF” / ”MANU” are not able to use the “AUTO”
setting of BW MODE.
NOTE
1) In the case that near infrared lighting is used the
hunting phenomenon causing repeated changes
between the color and B/W mode may occur. Avoid
strong near Infrared lighting when using the AUTO
Mode.
2) When the mode is changed to a B/W image where
there is no near infrared light a change in sensitivity
does not occur.
3) The focus face of the lens differs in visible light (the
color image) and near infrared (the B/W image).
The focus has deviated when the mode is changed
to a B/W image even if the focus was set properly for
the color image. Please use a lens having near
infrared response when using the B/W mode.
4) “AGC LIMIT” binds B/W mode AUTO to (H) or (M) at
the time of, “220” or more binding.
23
24
White Balance Menu [Only KP-DE500 type]
Setting White Balance mode
1) Press the SET button for longer than 2 seconds to display
the “MAIN MENU”.
2) Use the UP and DOWN buttons to shift the cursor to
“WHITE BALANCE”, then press the SET button to display
the “WHITE BALANCE MENU”. But, it does not move to
“WHITE BALANCE MENU” at the time of B/W image
condition by B/W MODE setting.
◆ ＷＨＩＴＥ ＢＡＬＡＮＣＥ ＭＥＮＵ ◆
>ＭＯＤＥ ：ＡＴＷ
ＡＴＷ ＲＡＮＧＥ ：ＮＯＲＭＡＬ
ＷＢ ＡＲＥＡ ：ＯＦＦ
ＲＥＴ
ＥＮＤ
WHITE BALANCE MENU (MODE: ATW)
3) While the cursor is at “MODE”, press the SET button to shift
the mode in the sequence “ATW”, “AWC” and “MANUAL”.
Factory setting is “ATW”.
…… Select White Balance mode
…… ATW Range setting
…… Select WB area mode
…… Return to the main menu
…… End of menu display
･ATW (auto tracking white balance)
Ordinarily use this mode, which is suitable for lighting
color temperature from 2,500K to 8,000K.
Setting ATW Range (Color temperature flattery range)
1) Use the UP and DOWN buttons to shift the cursor to
“ATW RANGE”.
2) Press the SET button to shift the mode in the sequence
“NORMAL”, “SPECIAL”. Factory setting is “NORMAL”.
NORMAL : From 2,500K to 8,000K
SPECAIL : From 2,500K to 8,000K, and special
lighting such as the mercury lamp and
sodium vapor lamp
NOTE
1) Please set “ATW RANGE” to the “SPECIAL” mode
when you use sodium lighting. The color
distinction becomes possible though the white
balance may not be completely suitable.
2) White balance cannot be fully adjusted in the
following situations.
･ Most of the scene is a single color or there is very
little white component.
･ Background is red or blue.
Setting WB detection area
1) Use the UP and DOWN buttons to shift the cursor to
“WB AREA”.
2) Press the SET button to shift the mode in the sequence
“OFF”, “ON(NO.*)”. [*1～9] Factory setting is “OFF”.
OFF : All the screens
ON(NO.*) [*1～9] : Only the selection area
3) When the display is turned “ON(NO.*), “AREA SELECT” is
displayed in the line in the under.
4) Shift the cursor to “AREA SELECT” and push the SET
button to display the detection area(WB) select menu.
ＡＲＥＡ（ＷＢ）
ＮＯ．１
┃ ┃
┃ ┃
┗━━━━━━┛
DETECTTION AREA (WB) SELECT MENU
┏━━━━━━┓
Detect area position
6 5
2
1 3
7
8 9
4
25
5) There are 9 white detect areas selected by the UP and
DOWN buttons. Select the areas from nos. 1 to 9 that
include the subject of main interest. (Factory setting is NO.1)
UP button : 1→2→3→4→5→6→7→8→9
(ascending order)
DOWN button : 9→8→7→6→5→4→3→2→1
(descending order)
6) After deciding the detection area, push the SET button to
return to the “WHITE BALANE MENU”.
26
A
r
A
･AWC (preset white balance)
fter white balance condition is set, it is automatically stored in
memory. The AWC mode should be used where the colo
temperature does not change once it has been set. The color
temperature adjustment range of AWC is 2300 K～10,000 K.
◆ ＷＨＩＴＥ ＢＡＬＡＮＣＥ ＭＥＮＵ ◆
>ＭＯＤＥ ：ＡＷＣ
ＰＲＥＳＥＴ ＳＴＡＲＴ ：ＰＵＳＨ ＳＥＴ
Ｒ－ＧＡＩＮ ＯＦＦＳＥＴ： ０００
Ｂ－ＧＡＩＮ ＯＦＦＳＥＴ： ０００
ＲＥＴ
ＥＮＤ
WHITE BALANCE MENU (MODE: AWC)
1) Use the UP and DOWN buttons to shift the cursor to
…… Select White Balance mode
…… Set preset start
…… Adjustment of the R gain offset
…… Adjustment of the B gain offset
…… Return to the main menu
…… End of menu display
“PRESET START”.
2) Select a white object to image near the center of the screen.
3) When a SET button switch is pushed, the white balance
adjustment is begun. At that time, “PUSH SET” enters the
state of blinking.
4) The cursor moves to “R-GAIN OFFSET” when the automatic
setting is completed. The time required in the automatic
setting changes depending on the light condition. If the
white balance is not correct after about 15 seconds, please
repeat the process from step 1.
Fine-tuning of white balance
fter Preset is completed, the white balance can be fine-tuned by
the R/B gain offset.
1) Use the UP and DOWN buttons to shift the cursor to
“R-GAIN OFFSET” or “B-GAIN OFFSET”, then press the
SET button. The adjustment value at the right of value
flashes.
2) Change the “R-GAIN OFFSET” or “B-GAIN OFFSET” by
pressing the UP and DOWN buttons.
(Variable range: -128～000～+127)
3) Return the factory setting(000) by simultaneously pressing
the UP and DOWN buttons for two seconds.
4) The setting is fixed when the SET button is pushed, and the
cursor moves below by one line.
･MANUAL (preset white balance)
◆ ＷＨＩＴＥ ＢＡＬＡＮＣＥ ＭＥＮＵ ◆
>ＭＯＤＥ ：ＭＡＮＵＡＬ
Ｒ－ＧＡＩＮ ： ０００
Ｂ－ＧＡＩＮ ： ０００
ＲＥＴ
ＥＮＤ
WHITE BALANCE MENU (MODE: MANUAL)
1) Use the UP and DOWN buttons to shift the cursor to
“R-GAIN” or “B-GAIN”, then press the SET button.
The adjustment value at the right of value flashes.
2) Change the “R-GAIN” or “B-GAIN” by pressing the UP and
DOWN buttons. (Variable range: -128～000～+127)
3) Return the factory setting(000) by simultaneously pressing
the UP and DOWN buttons for two seconds.
4) The setting is fixed when the SET button is pushed, and the
cursor moves below by one line.
…… Select White Balance mode
…… Adjustment of the R gain
…… Adjustment of the B gain
…… Return to the main menu
…… End of menu display
27
28
f
f
Sub Menu
The sub menu is used for changing the picture quality
(video response) of the camera output image.
1) Press the SET button for longer than 2 seconds to display
the “MAIN MENU”.
2) Use the UP and DOWN buttons to shift the cursor to
“SUB MENU”, then press the SET button to display the
“SUB MENU”.
◆ ＳＵＢ ＭＥＮＵ ◆
>ＩＴＥＭ ：ＰＩＣＴＵＲＥ
ＣＨＲＯＭＡ ： ０００
ＤＥＴＡＩＬ ： ０００
ＰＥＤＥＳＴＡＬ ： ０００
ＧＡＭＭＡ ：ＯＮ
ＤＮＲ ：ＡＵＴＯ（ＨＩＧＨ）
ＰＯＬＡＲＩＴＹ ：ＰＯＳＩＴＩＶＥ
ＲＥＴ
ＥＮＤ
･CHROMA [Only KP-DE500 Type]
The optimum color level has been set at the factory. If necessary,
this can be changed as follows.
1) Use the UP and DOWN buttons to shift the cursor to
SUB MENU (ITEM: PICTURE)
“CHROMA”, then press the SET button. The adjustment
value at the right of value flashes.
…… Select SUB MENU item
…… Chroma setting[*]
…… Detail setting
…… Pedestal level setting
…… Gamma setting
…… Digital noise reduction setting
…… Negative/positive
…… Return to the main menu
…… End of menu display
(*) Note: KP-E500 is not displayed.
2) Change the “CHROMA” by pressing the UP and DOWN
buttons. (Variable range: -128～000～+50)
3) Return the factory setting(000) by simultaneously pressing
the UP and DOWN buttons for two seconds.
4) The setting is fixed when the SET button is pushed, and the
cursor moves below by one line.
NOTE
1) The color noise might stand out when the color level
is raised.
2) CHROMA is fixed to “-128” and cannot be adjusted
by the B/W MODE setting at a monochrome image.
･DETAIL
The optimum detail level has been set at the factory. I
necessary, this can be changed as follows.
1) Use the UP and DOWN buttons to shift the cursor to
“DETAIL”, then press the SET button. The adjustment value
at the right of value flashes.
2) Change the “DETAIL” by pressing the UP and DOWN
buttons. (Variable range: -128～000～+127)
3) Return the factory setting(000) by simultaneously pressing
the UP and DOWN buttons for two seconds.
4) The setting is fixed when the SET button is pushed, and the
cursor moves below by one line.
29
NOTE
The noise might stand out when the detail level is raised.
･PEDESTAL
The optimum pedestal level has been set at the factory. I
necessary, this can be changed as follows.
1) Use the UP and DOWN buttons to shift the cursor to
“PEDESTAL”, then press the SET button. The adjustment
value at the right of value flashes.
2) Change the “PEDESTAL” by pressing the UP and DOWN
buttons. (Variable range: -128～000～+127)
3) Return the factory setting(000) by simultaneously pressing
the UP and DOWN buttons for two seconds.
4) The setting is fixed when the SET button is pushed, and the
cursor moves below by one line.
･GAMMA
1) Use the UP and DOWN buttons to shift the cursor to
“GAMMA”.
2) Press the SET button to shift the mode in the sequence
“ON”, “OFF”. Factory setting is “ON”.
OFF : γ=1.0
ON : γ=0.45
30
･DNR (Digital noise reduction)
It is a function to decrease the noise generation by AGC.
1) Use the UP and DOWN buttons to shift the cursor to “DNR”.
2) Press the SET button to select the setting sequentially in
the following order. Factory setting is “AUTO(HIGH)”.
SET button: AUTO(HIGH)→ON-1→ON-2→ON-3→ON-4
→ON-5→ON-6→ON-7→OFF
→AUTO(LOW)→AUTO(MID)
AUTO( ) : It synchronizes with the amplification of
AGC and the DNR setting changes from
turning “OFF” to “ON-7”.
LOW : Movement priority mode
(Change into “ON-5” in the maximum. )
MID : The middle mode
(Change into “ON-6” in the maximum. )
HIGH : Image quality priority mode
(Change into “ON-7” in the maximum. )
OFF : DNR doesn't operate.
ON-*(1～7) : DNR always operates. The afterimage
increases according to the coefficient of
the mode, and the noise decrease is
effective.
･POLARITY
1) Use the UP and DOWN buttons to shift the cursor to
“POLARITY”.
2) Press the SET button to shift the mode in the sequence
“POSITIVE”, “NEGATIVE”. Factory setting is “POSITIVE”.
The negative polarity is convenient when using negative
material, such as negative film.
･Change in submenu item
1) Use the UP and DOWN buttons to shift the cursor to
“ITEM”.
2) Press the SET button to shift the mode in the sequence
“PICTURE”, “PRESET”.
The display changes into the following menu when “ITEM” is
“PRESET”.
◆ ＳＵＢ ＭＥＮＵ ◆
>ＩＴＥＭ ：ＰＲＥＳＥＴ
ＢＵＲＳＴ ：ＯＮ
ＣＡＭ－ＲＥＳＥＴ ：ＰＵＳＨ ＳＥＴ
ＲＥＴ
ＥＮＤ
SUB MENU (ITEM: PRESET)
…… Select SUB MENU item
…… Burst signal ON/OFF of monochrome image [*]
…… Camera initialize
…… Return to the main menu
…… End of menu display
(*) Note: KP-E500 is not displayed.
･BURST [Only KP-DE500 type]
Burst signal ON/OFF when a monochrome image is output is set.
1) Use the UP and DOWN buttons to shift the cursor to
“BURST”.
2) Press the SET button to shift the mode in the sequence
“ON”, “OFF”. Factory setting is “ON”.
ON : The burst signal is added
OFF : The burst signal is not added
NOTE
A malfunction may occur when the camera is connected
to a VTR and monitor when the BURST is set to OFF.
Please change after confirming the specification of the
connected equipment enough.
･CAM-RESET
It returns the camera settings to the factory presets that were set
in the factory.
1) Use the UP and DOWN buttons to shift the cursor to
“CAM-RESET”.
2) Press the SET button for two seconds or
more, it executes it. Afterwards, it returns to the
“MAIN MENU”.
31
A
Remote menu operation
n optional remote plug is available to enable operating
the camera mode and set buttons by remote control.
Confirm the plug is properly wired as indicated in the
figure and connect it to the rear panel Remote connector.
Do not connect anything to the unused Pins.
Pin Signal Abbrev. Remarks
1 Not connected N.C. Do not connect
2 Serial data input Tx Connect to RS-232C
1
9
8 2
10
12 11
7
6
5
3
4
Remote plug(option)
External key switch connections for remote operation
Keep the distance between the remote plug and
external key switches to less than about 2 meters.
Disconnect the remote plug from the camera Remote
connector when not using the key switches.
UP
SET
DOWN
3 Serial data output Rx Connect to RS-232C
4 Up key UP Key switch connection
5 Down key DOWN Key switch connection
6 Not connected N.C. Do not connect
7 Not connected N.C. Do not connect
8 Set key SET Key switch connection
9 Not connected N.C. Do not connect
10 GND GND Connect to RS-232C
11 Not connected N.C. Do not connect
12 Not connected N.C. Do not connect
Remote operation with RS-232C
Signals 2, 3 and 10 can be used for control by personal
computer. Consult dealer for retailed information.
NOTE
Be sure to switch off the camera power before
connecting or disconnecting the remote plug.
data terminal
data terminal
ground
Specifications
1.Color system NTSC
2.Pickup element 1/2-inch progressive scan frame
Total pixels 680(H)
Effective pixels 658(H)
Scanning area 6.58(H)
Sell size 10.0(H)
3.Scanning system 2:1 interlace
4.Scanning frequency Hor. 15.734kHz
5.Sync system internal
6. Video signal output KP-DE500：VBS1.0Vp-p/75Ω
KP-E500：VS1.0Vp-p/75Ω
7. Signal processing Digital processing ( input 10 bits )
8. S/N( Y signal ) More than 50dB
(AGC,enhancer and gamma OFF)
9. Resolution( Y signal at center ) Hor. ：480 lines
Ver. ：350 lines
10.Minimum illumination
KP-DE500
0.009 lx ( Color, F1.4, AGC ON, SENS UP OFF, 50IRE )
0.0005 lx( Monochrome, F1.4, AGC ON, SENS UP OFF, 50IRE )
0.00015lx(Color 64 time accumulation, F1.4, AGC ON, 50IRE)
0.000008lx
(Monochrome 64 time accumulation, F1.4, AGC ON, 50IRE)
33
interline CCD( with on-chip microlenses )
× 500(V)
× 489(V)
× 4.89(V)mm
× 10.0(V)μm
Ver. 59.94Hz
32
KP-E500
0.0003 lx
(Monochrome, F1.4, AGC ON, SENS UP OFF, 50IRE )
0.000005 lx
(Monochrome 64 time accumulation, F1.4, AGC ON, 50IRE)
11. Sensitivity setting AGC OFF/ON(Factory setting is1/60)
Manual Gain Adjustable at AGC OFF
Limit Gain Adjustable at AGC ON
12. Electronic shutter speeds
Selectable in 7 steps & AES
( Factory setting is 1/60 )
1/60,1/100,1/125,1/250,1/500,1/1000,1/2000
AES:From 1/60 second to 1/2000 second
13.
Integration multiple [SENS UP] setting
：Automatic or Manual (fixed) ( Factory setting is OFF )
Automatic : 2,4,6,8,10,12,16,32,64 times
Manual : 2,4,6,8,10,12,16,32,64,88,128 times
14. Backlight compensation ON/OFFswitchable
Sensing area:selectable from 9 areas
15.Auto-iris lens outputs
Video signal
Input type lens
Iris control voltage input
(galvanometer)
Luminance signal
1.0Vp-p/high impedance
Power supply 12V DC 40mA
Coupling coil impedance
Damper:1150Ω±10%
Drive:190Ω±10%
16. White balance Selectable in 3 modes
Only KP-DE500 (Factory setting is ATW)
17. Text display 22 characters (number, alphabet, and mark)
18. B/W mode
Only KP-DE500 OFF (Color always mode)
(color) ON (B/W always mode)
Can be set for high, medium or low
19.NDR Selectable in 3 modes
OFF / AUTO / ON
20. Lens mount C/CS mount
21. Ambient temperature -10～＋50℃、30～80％RH
22. Storage ambient -20～＋60℃、20～90％RH
23. Power supply 12 VDC ± 10 %
24. Power consumption Approx. 1.5A
25. External dimensions 64(W)
26. .Mass Approx. 610g
(color) Auto-tracking[ATW] / preset[AWC] /
R/B gain manual control[MANUAL]
Selectable in 3 modes (Factory setting is OFF)
AUTO(Mode selected in response to
brightness)
(Noise reduction) ( Factory setting is AUTO(HI) )
(Omitting 40mA for auto-iris lens)
× 63(H)× 123(D)mm
Note:
If used continuously, be sure to operate at less than
40℃ for long term stable performance.
Accessories
Supplied accessories
Operation manual 1
DC input plug (R03-P3F) 1
Optional accessories
Lenses (see Page 7 )
Remote plug HR-10A-10P-12P(01) (Part code: JMH0093)
34
Loading...