Hitachi Freedom Storage Lightning 9900 V Error Code List

Hitachi Freedom Storage™

Lightning 9900™ V Series

Remote Console Error Codes

© 2002 Hitachi Data Systems Corporation, ALL RIGHTS RESERVED

Notice: No part of this publication may be reproduced or transmitted in any form or by any electronic or mechanical means, including photocopying and recording, or stored in a database or retrieval system for any purpose, without the express written permission of Hitachi Data Systems Corporation.

Hitachi Data Systems reserves the right to make changes to this document at any time without notice and assumes no responsibility for its use. Hitachi Data Systems products and services can only be ordered under the terms and conditions of Hitachi Data Systems’ applicable agreements, including license agreements. All of the features described in this document may not be currently available. Refer to the most recent product announcement or contact your Hitachi Data Systems representative for information on feature and product availability.

This document contains the most current information available at the time of publication. When new and/or revised information becomes available, this entire document will be updated and distributed to all registered users.

Trademarks

Hitachi Data Systems is a registered trademark and service mark of Hitachi, Ltd. The Hitachi Data Systems design mark is a trademark and service mark of Hitachi, Ltd.

Hitachi Freedom Storage and Lightning 9900 are trademarks of Hitachi Data Systems Corporation.

S/390 is a registered trademark of International Business Machines Corporation.

All other brand or product names are or may be registered trademarks, trademarks or service marks of and are used to identify products or services of their respective owners.

Notice of Export Controls

Export of technical data contained in this document may require an export license from the United States government and/or the government of Japan. Contact the Hitachi Data Systems Legal Department for any export compliance questions.

Document Revision Level

Revision Date Description

MK-92RD132-P April 2002 Preliminary Release

MK-92RD132-0 May 2002 Initial Release

Hitachi Lightning 9900™ V Series Remote Console Error Codes iii

Source Documents for this Revision

 Ecd45d0a.doc (RSD source document)

Changes in this Revision

 Added description of Remote Console messages (new section 1.1).

 Added severity level N and failure level 7 (section 1.2).

 Added error codes: 0001 5075, 0001 5508, 0001 5509, 0002 5510, 0003 2085-2094,

0405 5013, 1110 9080, 3010 9019, 5310 1110.

 Revised message text and recommended action for error codes: 0002 2016, 0003 2085-

2094, 0110 5085, 1110 1110.

Referenced Documents

 Hitachi Lightning 9900™ V Series User and Reference Guide, MK-92RD100

 Hitachi Lightning 9900™ V Series Hitachi Remote Console – Storage Navigator User’s

Guide, MK-92RD101

iv Preface

Preface

This document presents a list of the error codes and error messages for the Lightning 9900™ V Series Remote Console and provides recommended action for each error condition. This document assumes that:

 the user has a background in data processing and understands direct-access storage

 the user is familiar with the Hitachi Freedom Storage™ Lightning 9900™ V Series array

 the user is familiar with the Hitachi Remote Console – Storage Navigator software for the

For further information on the Lightning 9900™ V Series subsystem, please refer to the Hitachi Lightning 9900™ V Series User and Reference Guide (MK-92RD100), or contact your Hitachi Data Systems account team.

For further information on the Hitachi Remote Console – Storage Navigator software, please refer to the Hitachi Lightning 9900™ V Series Hitachi Remote Console – Storage Navigator User’s Guide (MK-92RD101).

Note: In this document the term “9900V” refers to the entire Hitachi Lightning 9900™ V Series subsystem family, unless otherwise noted.

device (DASD) subsystems and their basic functions, and

subsystem, and

Lightning 9900™ V Series subsystem.

Note: The use of the Lightning 9900™ V Series subsystem, Hitachi Remote Console – Storage Navigator software, and all other Hitachi Data Systems products is governed by the terms of your license agreement(s) with Hitachi Data Systems.

Microcode Level

This document revision applies to 9900V microcode versions 21-01-xx and higher.

Please send us your comments on this document: doc.comments@hds.com.

Make sure to include the document title, number, and revision.

Please refer to specific page(s) and paragraph(s) whenever possible.

(All comments become the property of Hitachi Data Systems Corporation.)

COMMENTS

Thank you!

Hitachi Lightning 9900™ V Series Remote Console Error Codes v

vi Preface

Chapter 1 Remote Console Messages and Error Codes

1.1 Remote Console Messages

Figure 1.1 shows a typical message panel displayed by the Hitachi Lightning 9900™ V Series Remote Console – Storage Navigator software.

Figure 1.1 Sample Error Message

All 9900V message panels display the following information:

 Message level:

Information

Warning

Fatal error

The server is unable to accept the request from the Remote Console.

One possible cause is that some processing is in progress at the server. This message does not indicate an error.

 Message text: Descriptive text, may include variables %s (character string) and %d

(numeral). The values of these variables are determined when processing is performed.

 Part code: The ID of the application that issued the message. In Figure 1.1 the part

code is 110.

 Message number: decimal number within the range of 0000 to 9999. In Figure 1.1 the

message number is 9102.

Hitachi Lightning 9900™ V Series Remote Console Error Codes 1

1.2 Error Codes

Table 1.1 lists the error codes and error messages for the Lightning 9900™ V Series Remote Console and provides recommended action for the error conditions. Table 1.1 also provides the severity level and failure level of each error condition.

Severity Levels. The severity levels for the 9900V error codes are:

 I: Information

 E: Error

 W: Warning

 N: The server is unable to accept the request from the Remote Console.

One possible cause is that some processing is in progress at the server. This message does not indicate an error.

Failure Levels. The failure levels for the 9900V error codes are:

 O: No Error

 1: Select MSG OK to end forcibly

 2: Exit is valid only

 3: Refresh/Exit is valid only

 4: To make refresh possible

 5: No status change

 6: No change with refreshing automatically

 7: Remote Console will automatically be switched to view mode. If necessary, you must

change the mode to modify mode.

Table 1.1 Error Codes

Part

Error

Code

Number

0001 1000 An error occurred. If this problem persists, please call

0001 1001 An error occurred. If this problem persists, please call

0001 1002 An error occurred. If this problem persists, please call

0001 1003 An error occurred. If this problem persists, please call

0001 1004 An error occurred. If this problem persists, please call

0001 2000 An error occurred. If this problem persists, please call

0001 2001 An error occurred. If this problem persists, please call

0001 2002 An error occurred. If this problem persists, please call

Error Message Recommended Action

the Support Center.

If nothing changes despite retrying, call the service personnel.

Severity Level

Failure Level

E 2

2 Chapter 1 Error Codes

0001 2005 An error occurred. If this problem persists, please call

the Support Center.

Call the service personnel. E 2

0001 3000 An error occurred. If this problem persists, please call

the Support Center.

0001 3001 An error occurred. If this problem persists, please call

the Support Center.

0001 3002 An error occurred. If this problem persists, please call

the Support Center.

0001 4001 An error occurred. If this problem persists, please call

the Support Center.

0001 4003 An error occurred. If this problem persists, please call

the Support Center.

0001 4004 An error occurred. If this problem persists, please call

the Support Center.

0001 4005 The user ID is already logged in. Do you want to log in

forcibly?

0001 4006 An error occurred. If this problem persists, please call

the Support Center.

0001 4007 An error occurred. If this problem persists, please call

the Support Center.

0001 4008 An error occurred. If this problem persists, please call

the Support Center.

0001 4009 An error occurred. If this problem persists, please call

the Support Center.

Call the service personnel. E 2

Reduce the set processing number and retry. E 2

Reduce the number of the characters set. E 2

Call the service personnel. E 3

Input the correct user name and log in again. E 2

Input the correct password and log in again. E 2

Since the same user name is being used, log in with the other user name.

Call the service personnel. E 2

W 5

0001 4010 An error occurred. If this problem persists, please call

the Support Center.

0001 4011 An error occurred. If this problem persists, please call

the Support Center.

0001 4012 The number of connections set exceeds the

maximum(32).

0001 4013 The server configuration is invalid. Please call the

Support Center.

0001 4020 Network error detected; exclusive lock is released. Lock is removed. Lock again. E 2

0001 5075 This key code is invalid. Please input the correct key code. W 5

0001 5132 You cannot log on because the specified user ID is

already being logged on, or because the termination process in the previous logon was not performed properly.

0001 5508 An administrator is changing a system environment

file. Please log on again after waiting for a while.

0001 5509 Modify mode was canceled forcibly. If you want to make settings, please change to

0001 7050 An error occurred. If this problem persists, please call

the Support Center.

The error occurs only in the internal process. E 2

Log in again. E 2

The number of the users is the maximum. Wait for a while and retry.

Failed to access the Config file. Call the service personnel.

Log on with other user's ID. There is a possibility that the termination process in the previous logon was invalid. (Terminated by pressing the end button of the browser.) After RMI Time-out (default 1 min.), log on again.

Please log on again after waiting for a while. E 1

Modify mode.

Call the service personnel. E 2

E 2

E 1

W 7

Hitachi Lightning 9900™ V Series Remote Console Error Codes 3

0002 2001 An error occurred. If this problem persists, please call

the Support Center.

If nothing changes despite retrying, call the service personnel.

E 2

0002 2002 An error occurred. If this problem persists, please call

the Support Center.

0002 2003 An error occurred. If this problem persists, please call

the Support Center.

0002 2004 An error occurred. If this problem persists, please call

the Support Center.

0002 2005 An error occurred. If this problem persists, please call

the Support Center.

0002 2006 An error occurred. If this problem persists, please call

the Support Center.

0002 2006 An error occurred. If this problem persists, please call

the Support Center.

0002 2007 An error occurred. If this problem persists, please call

the Support Center.

0002 2008 An error occurred. If this problem persists, please call

the Support Center.

0002 2009 An error occurred. If this problem persists, please call

the Support Center.

0002 2010 An error occurred. If this problem persists, please call

the Support Center.

0002 2011 The server configuration is invalid. Please call the

Support Center.

If nothing changes despite retrying, call the service personnel.

Call the service personnel. E 2

If nothing changes despite retrying, call the service personnel.

Call the service personnel. E 2

E 2

E 3

0002 2012 An error occurred. If this problem persists, please call

the Support Center.

0002 2013 An error occurred. If this problem persists, please call

the Support Center.

0002 2015 An error occurred. If this problem persists, please call

the Support Center.

0002 2016 Array is refreshing, or the settings by the user are

being registered. Please retry in a while.

0002 5040 The maximum number which can be processed was

exceeded. Please reduce the number of requests and try again.

0002 5130 A sequence error occurred. Please call the developer

of the client program.

0002 5510 Array is refreshing, or some other user is changing

configuration. After you reply to this message, a panel appears which contains only the Refresh button and Exit button. Please select the Refresh button after a while.

0002 6012 An error occurred. If this problem persists, please call

the Support Center.

0002 6022 An error occurred. If this problem persists, please call

the Support Center.

Call the service personnel. E 2

The volume which links as an expanded LU extend over CU#. The error does not occur normally because it is guarded in the screen. Contact the program maker.

Call the service personnel. E 2

Please retry after a while. N 6

You cannot specify anymore. W 6

Connection is terminated from the server due to the network failure etc. Log in again.

Please select the Refresh button after a while. N 3

If the same error occurs despite retrying, call the service personnel.

E 2

E 5

E 2

4 Chapter 1 Error Codes

0002 6023 An error occurred. If this problem persists, please call

the Support Center.

Call the service personnel. E 2

0002 7030 An error occurred. If this problem persists, please call

the Support Center.

0002 7060 An error occurred. If this problem persists, please call

the Support Center.

0002 7211 An error occurred. If this problem persists, please call

the Support Center.

0002 9000 Another user has lock, please try again later. Another user is accessing with Modify mode.

0002 9001 An error occurred. If this problem persists, please call

the Support Center.

0002 9999 An error occurred. If this problem persists, please call

the Support Center.

0003 1002 The specified volume cannot be set as the Command

Device, because the volume is being used as a TrueCopy/ShadowImage volume. Select another volume.

0003 1003 An error occurred. If this problem persists, please call

the Support Center.

0003 1004 An error occurred. If this problem persists, please call

the Support Center.

Call the service personnel. E 2

Wait for while and retry.

Modify mode is not preserved. Preserve the Modify mode and execute.

Call the service personnel. E 2

Correct the contents of the command device setting, and request the setting of the configuration information again.

The setting of the command device security is requested, or the command device of the target volume is not set. The error does not occur normally because it is guarded in the screen. Contact the program maker.

A file access error occurs for the file required by the agent. Contact the Hitachi Data Systems Support Center.

E 5

E 2

E 6

E 2

0003 1005 An error occurred. If this problem persists, please call

the Support Center.

0003 1007 Failed to remove the path. The specified path is the

last path of TrueCopy/ShadowImage volume.

0003 1009 An error occurred. If this problem persists, please call

the Support Center.

0003 1010 An error occurred. If this problem persists, please call

the Support Center.

0003 1011 An error occurred. If this problem persists, please call

the Support Center.

0003 1012 An error occurred. If this problem persists, please call

the Support Center.

0003 1013 An error occurred. If this problem persists, please call

the Support Center.

0003 1015 An error occurred. If this problem persists, please call

the Support Center.

0003 1018 An error occurred. If this problem persists, please call

the Support Center.

A nickname is not specified when the configuration change of LUN-Security is requested. The error does not occur normally because it is guarded in the screen. Contact the program maker.

Correct the contents of LU path setting, and request the setting of the configuration information again.

Call the service personnel. E 2

E 2

E 6

Hitachi Lightning 9900™ V Series Remote Console Error Codes 5

0003 1020 An error occurred. If this problem persists, please call

the Support Center.

Call the service personnel. E 2

0003 1021 An error occurred. If this problem persists, please call

the Support Center.

0003 1022 An error occurred. If this problem persists, please call

the Support Center.

0003 1024 An error occurred. If this problem persists, please call

the Support Center.

0003 1025 An error occurred. If this problem persists, please call

the Support Center.

0003 1027 An error occurred. If this problem persists, please call

the Support Center.

0003 1028 An error occurred. If this problem persists, please call

the Support Center.

0003 1029 An error occurred. If this problem persists, please call

the Support Center.

Call the service personnel. E 2

CHA high-speed mode is specified to unmounted CHA. The error does not occur normally because it is guarded in the screen. Contact the program maker.

CHA high-speed mode is specified, but a topology includes what the high-speed mode cannot be set. The error does not occur normally because it is guarded in the screen. Contact the program maker.

CHA high-speed mode is specified, Fibre Address of the specified port includes what the high-speed mode cannot be set. The error does not occur normally because it is guarded in the screen. Contact the program maker.

Channel speed change is requested, but Fibre PCB does not support it. The error does not occur normally because it is guarded in the screen. Contact the program maker.

E 2

0003 1031 An error occurred. If this problem persists, please call

the Support Center.

0003 1033 An error occurred. If this problem persists, please call

the Support Center.

0003 1034 An error occurred. If this problem persists, please call

the Support Center.

0003 1035 An error occurred. If this problem persists, please call

the Support Center.

0003 1036 An error occurred. If this problem persists, please call

the Support Center.

0003 1037 An error occurred. If this problem persists, please call

the Support Center.

Command device setting is requested for Reserve volume of CruiseControl/On-Demand volume. Or it is requested for volumes other than open volumes (including un-installed volumes). The error does not occur normally because it is guarded in the screen. Contact the program maker.

CU, which is specified during Virtual LVI/LUN operation (Install CV) cannot be set. The error does not occur normally because it is guarded in the screen. Contact the program maker.

Virtual LVI/LUN operation is requested for uninstalled volumed. The error does not occur normally because it is guarded in the screen. Contact the program maker.

FlashAccess pre-staging command was accepted, but FlashAccess setting is not done. Or FlashAccess setting is done, but pre-staging is not set. The error does not occur normally because it is guarded in the screen. Contact the program maker.

Download error occurs. Call the service personnel.

Failed to acquire the external function pointer for obtaining race information. Contact the Hitachi Data Systems Support Center.

E 2

6 Chapter 1 Error Codes

0003 1038 An error occurred. If this problem persists, please call

the Support Center.

Failed to acquire the external function pointer which is required by the agent. Contact the Hitachi Data Systems Support Center.

E 2

0003 1039 An error occurred. If this problem persists, please call

the Support Center.

0003 1040 An error occurred. If this problem persists, please call

the Support Center.

0003 1041 An error occurred. If this problem persists, please call

the Support Center.

0003 1042 An error occurred. If this problem persists, please call

the Support Center.

0003 1043 An error occurred. If this problem persists, please call

the Support Center.

0003 1044 An error occurred. If this problem persists, please call

the Support Center.

0003 1045 The specified Subsystem ID already exists. Specify

another SSID.

0003 1048 An error occurred. If this problem persists, please call

the Support Center.

Failed to connect the communication between DKCs (SVPs). If the same error occurs despite retrying, call the service personnel.

Failed to load files necessary for the execution. (Insufficient memory, or the necessary files do not exist.) If the same error occurs despite retrying, call the service personnel.

Failed to read the information on configuration from DKC (SVP). If the same error occurs despite retrying, call the service personnel.

Failed to reserve the memory required for the execution. If the same error occurs despite retrying, call the service personnel.

Failed to write MIB management information. Contact the Hitachi Data Systems Support Center.

Correct the specified content, and issue the request again.

Fibre topology information is invalid. (The specified value is not in the specification.) The error does not occur normally because it is guarded in the screen. Contact the program maker.

E 2

E 5

E 2

0003 1049 An error occurred. If this problem persists, please call

the Support Center.

0003 1050 An error occurred. If this problem persists, please call

the Support Center.

0003 1051 An error occurred. If this problem persists, please call

the Support Center.

0003 1059 An error occurred. If this problem persists, please call

the Support Center.

0003 1061 An error occurred. If this problem persists, please call

the Support Center.

0003 1062 An error occurred. If this problem persists, please call

the Support Center.

0003 1063 The specified WWN is already in use. Specify another

WWN.

Host group number, which is not registered, is specified. (When deleting, or changing) The error does not occur normally because it is guarded in the screen. Contact the program maker.

Host mode is invalid. (The specified value is not in the specification.) The error does not occur normally because it is guarded in the screen. Contact the program maker.

Instruction was given to a logical parity group which is not installed in Virtual LVI/LUN operation. The error does not occur normally because it is guarded in the screen. Contact the program maker.

Interface logical error in the agent is detected. Or a non-registered error occurs. Contact the Hitachi Data Systems Support Center.

Internal logical error is detected. Contact the Hitachi Data Systems Support Center.

Correct the specified contents, and request the setting of the configuration information again.

E 2

E 6

Hitachi Lightning 9900™ V Series Remote Console Error Codes 7

0003 1065 The specified Name is already in use. Correct the specified contents, and request the

setting of the configuration information again.

E 6

0003 1066 An error occurred. If this problem persists, please call

the Support Center.

0003 1067 An error occurred. If this problem persists, please call

the Support Center.

0003 1068 An error occurred. If this problem persists, please call

the Support Center.

0003 1074 An error occurred. If this problem persists, please call

the Support Center.

0003 1075 An error occurred. If this problem persists, please call

the Support Center.

0003 1101 An error occurred. If this problem persists, please call

the Support Center.

0003 1102 Volume initialization operation cannot take to the last

LDEV of RAID striping group.

0003 1103 An error occurred. If this problem persists, please call

the Support Center.

Internal logical error is detected. Contact the Hitachi Data Systems Support Center.

Invalid interface between the functions inside the agent is detected. Contact the Hitachi Data Systems Support Center.

LU path is set to a volume which links as an expanded LU. The error does not occur normally because it is guarded in the screen. Contact the program maker.

LU path is set to the releasing expanded LU. (You need to release the expanded LU and path at the same time.) The error does not occur normally because it is guarded in the screen. Contact the program maker.

Since at least one LDEV is required in the parity group, you cannot de-install anymore.

LUN is invalid. (The specified value is not in the specification.) The error does not occur normally because it is guarded in the screen. Contact the program maker.

E 2

E 6

E 2

0003 1104 An error occurred. If this problem persists, please call

the Support Center.

0003 1105 An error occurred. If this problem persists, please call

the Support Center.

0003 1108 An error occurred. If this problem persists, please call

the Support Center.

0003 1111 An error occurred. If this problem persists, please call

the Support Center.

0003 1113 The selected CU:LDEV cannot be apply because it is

being used by HPAV. Please select another CU:LDEV.

0003 1116 An error occurred. If this problem persists, please call

the Support Center.

0003 1123 An error occurred. If this problem persists, please call

the Support Center.

0003 1124 An error occurred. If this problem persists, please call

the Support Center.

0003 1125 An error occurred. If this problem persists, please call

the Support Center.

Port blockade error occurs. Call the service personnel.

Port recovery error occurs. Call the service personnel.

Reserve volume of CruiseControl or On-Demand volume is included to a volume which links as an expanded LU. The error does not occur normally because it is guarded in the screen. Contact the program maker.

Retry the same operation. If the same error occurs despite retrying, call the service personnel.

After changing the volume which creates CV in Virtual LVI/LUN operation, retry the Virtual LVI/LUN operation.

Retry the same operation. If the same error occurs, call the service personnel.

E 2

E 6

E 2

8 Chapter 1 Error Codes

0003 1126 The Command Device cannot be set within a LUSE

volume. Select another volume.

Correct the specified contents, and request again.

E 5

0003 1127 An error occurred. If this problem persists, please call

the Support Center.

0003 1128 An error occurred. If this problem persists, please call

the Support Center.

0003 1129 An error occurred. If this problem persists, please call

the Support Center.

0003 1130 The specified name is the same as the system default

name. Please change the name.

0003 1131 An error occurred. If this problem persists, please call

the Support Center.

0003 1132 An error occurred. If this problem persists, please call

the Support Center.

0003 1133 An error occurred. If this problem persists, please call

the Support Center.

Subsystem ID, which is required for Virtual LVI/LUN operation, is not set. The error does not occur normally because it is guarded in the screen. Contact the program maker.

SVP and DKC are processing Virtual LVI/LUN. Wait for a while, and request the setting of the configuration information again.

SVP or DKC micro program cannot execute the request. (The version cannot execute the request.) If the same error occurs despite retrying, call the service personnel.

Correct the specified contents, and request again.

The CU numer specified in Virtual LVI/LUN operation and LDEV number overlap with other volume number. The error does not occur normally because it is guarded in the screen. Contact the program maker.

The directory of MIB management information does not exist. Contact the Hitachi Data Systems Support Center.

The emulation type is specified incorrectly in Virtual LVI/LUN operation. The error does not occur normally because it is guarded in the screen. Contact the program maker.

E 2

E 6

E 2

0003 1134 An error occurred. If this problem persists, please call

the Support Center.

0003 1135 An error occurred. If this problem persists, please call

the Support Center.

0003 1136 An error occurred. If this problem persists, please call

the Support Center.

0003 1137 An error occurred. If this problem persists, please call

the Support Center.

0003 1201 Invalid components for High Speed mode. The

specified port cannot be changed to High Speed mode.

0003 1203 An error occurred. If this problem persists, please call

the Support Center.

The emulation type of a volume which links as an expanded LU is not Open volume. The error does not occur normally because it is guarded in the screen. Contact the program maker.

The emulation type of a volume which links as an expanded LU is not the same. The error does not occur normally because it is guarded in the screen. Contact the program maker.

The instruction of the whole volume in FlashAccess is specified to the mainframe volume. The error does not occur normally because it is guarded in the screen. Contact the program maker.

The method of specifying FlashAccess setting place and the volume type do not match. (LBA number is specified to main frame volume. Cylinder number /header number is specified to Open volume.) The error does not occur normally because it is guarded in the screen. Contact the program maker.

Change the parameter to a path where the highspeed mode can be set, and request again.

The number of LDEV ID which can be set in Virtual LVI/LUN operation is exceeded. The error does not occur normally because it is guarded in the screen. Contact the program maker.

E 2

E 5

E 2

Hitachi Lightning 9900™ V Series Remote Console Error Codes 9

0003 1204 An error occurred. If this problem persists, please call

the Support Center.

The number of volumes which link as expanded LUs is beyond the range. The error does not occur normally because it is guarded in the screen. Contact the program maker.

E 2

0003 1350 Add path to the initiator port failed. The port you are trying to set is for Fibre

TrueCopy. You need to change the attribute when adding a path. Attribute (Target or RCU Target)

0003 1351 Failed to change to High Speed mode with specified

port attribute.

The port you are trying to set is for Fibre TrueCopy. You need to change all the attributes of the port to initiator, when you changing to the high-speed mode.

0003 1352 Logical paths remain on the Fibre-MCU port. This

operation may cause a fatal damage to the logical paths , so stop this operation. If you want to continue

Since the port you are trying to set is for Fibre TrueCopy, you need to delete the logical path,

and then set. this operation, please remove the logical paths from the MCU port at first.

0003 1353 S-VOLs remain on the Fibre-RCU port. This operation

may cause a fatal damage to S-VOLs, so stop this operation. If you want to continue this operation,

Since the port you are trying to set is for Fibre

TrueCopy, you need to delete the S-VOL logical

path which is set to RCU Target, and then set. please remove the S-VOLs from the RCU port at first.

0003 1354 Failed to add the WWN to the initiator port. The port you are trying to set is for Fibre

TrueCopy. You need to change the attribute

when adding a WWN. Attribute (Target or RCU

Target)

0003 1355 Host group to the initiator port cannot be changed. The port you are trying to set is for Fibre

TrueCopy. You need to change the attribute

when adding a WWN. Attribute (Target or RCU

Target)

E 6

0003 1356 Host group to the initiator port cannot be added. The port you are trying to set is for Fibre

TrueCopy. You need to change the attribute

when adding a host group. Attribute (Target or

RCU Target)

0003 1600 This functionality is not available. LUN Management is

Install the necessary program product. E 6 required.

0003 1601 This functionality is not available. Open Volume

Install the necessary program product. E 6 Management is required.

0003 1602 This functionality is not available. Virtual LVI is

Install the necessary program product. E 6 required.

0003 1603 This functionality is not available. FlashAccess is

Install the necessary program product. E 6 required.

0003 1604 This functionality is not available. FlashAccess -

S/390

®

is required.

0003 2002 An error occurred. If this problem persists, please call

the Support Center.

Install the necessary program product. E 6

The setting method of command

device/command device security is incorrect. The

following settings are invalid.

*Set command device+Release command device

security

*Release command device+Set command device

security.

It does not occur normally because it is guarded

in the screen. Contact the program maker.

E 6

E 2

10 Chapter 1 Error Codes

0003 2003 An error occurred. If this problem persists, please call

the Support Center.

The size of CV is larger than the possible size. (It is smaller than the minimum size, or is larger than the maximum.) The error does not occur normally because it is guarded in the screen. Contact the program maker.

E 2

0003 2004 An error occurred. If this problem persists, please call

the Support Center.

0003 2005 An error occurred. If this problem persists, please call

the Support Center.

0003 2006 An error occurred. If this problem persists, please call

the Support Center.

0003 2009 An error occurred. If this problem persists, please call

the Support Center.

0003 2010 The LDEV is in use by the HOST, or an error occurred

in the server procedure.

0003 2011 You cannot perform processing because a volume

pair is being created for remote copy operations, correction copy is in progress, or the LDEV is closed. Release the volume pair or wait for a while and then retry processing. If you still cannot perform processing, please call the technical support center.

The specified area in FlashAccess is beyond the volume size. The error does not occur normally because it is guarded in the screen. Contact the program maker.

The specified LU path does not exist. (You have specified wrong path control index.) The error does not occur normally because it is guarded in the screen. Contact the program maker.

The specified port does not exist. You have specified a wrong port number. Or the specified port type (exclusively for mainframe) cannot be processed in this agent. The error does not occur normally because it is guarded in the screen. Contact the program maker.

The specified value of the command device setting is invalid. (The specified value is not in the specification.) The error does not occur normally because it is guarded in the screen. Contact the program maker.

Check if I/O from the host to target path/volume does not occur.

Check the DKC status (if it is blocked or not). If the same error occurs again, call the service personnel.

E 2

E 6

W 6

0003 2012 An error occurred. If this problem persists, please call

the Support Center.

0003 2013 An error occurred. If this problem persists, please call

the Support Center.

0003 2014 An error occurred. If this problem persists, please call

the Support Center.

0003 2015 An error occurred while connecting to the subsystem.

Please retry a little later.

0003 2016 SNMP or SVP has lock, please try again later. Wait for a while and reissue the request. E 5

0003 2017 Network error detected; exclusive lock is released. Request again. (Re-execute exclusive lock start

The specified volume does not exist, or the delete request was given to a volume where FlashAccess is not specified. The error does not occur normally because it is guarded in the screen. Contact the program maker.

The specified volume does not exist. (You have specified wrong CU#:LDEV#) Or the LDEV (exclusively for mainframe) cannot be procesed in this agent. The error does not occur normally because it is guarded in the screen. Contact the program maker.

There is no capacity left in the logical parity group to create CV. The error does not occur normally because it is guarded in the screen. Contact the program maker.

Communication error occurs. If the same error occurs despite retrying, call the service personnel.

request.)

E 2

E 6

E 2

Hitachi Lightning 9900™ V Series Remote Console Error Codes 11

0003 2022 An error occurred. If this problem persists, please call

the Support Center.

There is no host group where WWN is

registered. The error does not occur normally

because it is guarded in the screen. Contact the

program maker.

E 2

0003 2033 The server is not ready yet, or an internal processing

is being executed. Please wait a while, and then click the Refresh button.

0003 2080 Prestaging not completed. Wait for a while, and press the Refresh button,

0003 2081 An error occurred during custom volume

install/uninstall operation. Please retry.

0003 2082 The process can not be performed, because a host is

mounted or a cluster configuration is set.

0003 2083 The subsystem status is invalid. Please call the

Support Center.

0003 2084 The subsystem status is invalid. Please call the

Support Center.

0003 2085 Copying is in progress for Remote

Copy/ShadowImage/ShadowImage- S/390(R) pairs. Please wait for a while and then retry.

0003 2086 The configuration of ShadowImage/ShadowImage-

S/390(R) is defined. Reset the configuration definetion, and then retry the operation.

Wait for a while, and press the Refresh button. E 3

and then change the same configuration again.

Or check the DKC status (if it is not blocked). If

the same error occurs, call the service personnel.

If the same error occurs, call the service

personnel.

Host is mounted, or cluster configuration is set.

Release the status.

Check the DKC status and the current status of

the configuration setting. If necessary, re-

execute the setting operation.

Check the DKC status and the current status of

the configuration setting. If necessary, re-

execute the setting operation.

Please wait for awhile and then retry. W 6

Reset the configuration definetion, and then retry

the operation.

E 6

E 2

W 6

0003 2087 The system is online from the mainframe host. Vary

the subsystem offline from the host.

0003 2088 The Remote Copy pair is suspended. Add an

alternative path.

0003 2089 The corresponding CHA might contain the last path

between the MCU and RCU of Remote Copy. Make sure that there is an alternative path from the MCU.

0003 2090 The ShadowImage/ShadowImage - S/390(R) settings

exist. Either reset the settings or stop the I/Os, and then retry the operation.

0003 2091 The backup server of ShadowImage/ShadowImage -

S/390(R) is running . Please stop it and then retry.

0003 2092 Some ShadowImagae/ShadowImage- S/390(R) pairs

exist. Please split them.

0003 2093 Some ShadowImagae/ShadowImage- S/390(R) pairs

exist. Please resynchronize them.

0003 2094 Some ShadowImagae/ShadowImage- S/390(R) pairs

exist. Please change the status of their volumes to Simplex.

Vary the subsystem offline from the host. W 6

Add an alternative path. W 6

Make sure that there is an alternative path from

the MCU.

Either reset the settings or stop the I/Os, and

then retry the operation.

Please stop the backup server and then retry. W 6

Please split the ShadowImage pairs. W 6

Please resynchronize the ShadowImage pairs. W 6

Please change the status of their volumes to

Simplex.

W 6

12 Chapter 1 Error Codes

0003 3000 An error occurred. If this problem persists, please call

the Support Center.

When a path is set (add/delete), the maximum value you can set in the PORT is exceeded. The error does not occur normally because it is guarded in the screen. Contact the program maker.

E 2

0003 3001 An error occurred. If this problem persists, please call

the Support Center.

0003 3002 An error occurred. If this problem persists, please call

the Support Center.

0003 3003 An error occurred. If this problem persists, please call

the Support Center.

0003 3004 An error occurred. If this problem persists, please call

the Support Center.

0003 3005 An error occurred. If this problem persists, please call

the Support Center.

When CHA high-speed mode is set, multiple change instructions are set to the same PORT. The error does not occur normally because it is guarded in the screen. Contact the program maker.

When Virtual LVI/LUN operation (Volume Initialize) is performed, CV is not set in the target logical parity group. The error does not occur normally because it is guarded in the screen. Contact the program maker.

When host group is set (add/change/delete), the maximum value you can set in the PORT is exceeded. The error does not occur normally because it is guarded in the screen. Contact the program maker.

When PORT information (Fibre Address/Fibre Topology/Channel Speed) is set, multiple change instructions are set to the same PORT. The error does not occur normally because it is guarded in the screen. Contact the program maker.

When WWN is registered in LUN-Security operation, the number of WWNs you can register is exceeded. The error does not occur normally because it is guarded in the screen. Contact the program maker.

E 2

0003 3006 An error occurred. If this problem persists, please call

the Support Center.

0003 3007 An error occurred. If this problem persists, please call

the Support Center.

0004 2006 An error occurred. If this problem persists, please call

the Support Center.

0004 6037 The subsystem status is invalid. Please call the

Support Center.

0004 8010 The subsystem status is invalid. Please call the

Support Center.

0005 5099 An error occurred. If this problem persists, please call

the Support Center.

0005 5200 This functionality is not available. SNMP API is

required.

When WWN is set (add/change), the maximum value you can set in the PORT is exceeded. The error does not occur normally because it is guarded in the screen. Contact the program maker.

When you perform Virtual LVI/LUN (Volume Initialize), only Deleted Normal Volume information is specified. The error does not occur normally because it is guarded in the screen. Contact the program maker.

Call the service personnel. E 2

Retry the same operation several times. If the same error occurs, call the service personnel.

You are trying to perform LUN Security operation for non-Fibre port. The error does not occur normally because it is guarded in the screen. Contact the program maker.

Install the program product. E 6

E 2

Hitachi Lightning 9900™ V Series Remote Console Error Codes 13

0005 5201 This functionality is not available. Hitachi Parallel

Access Volume is required.

Install the program product. If you want to

perform release process, release after the

emergency key is installed.

E 6

0005 5202 This functionality is not available. Performance

Monitor is required.

0005 5203 This functionality is not available. Hitachi

CruiseControl is required.

0005 5204 This functionality is not available. Priority Access is

required.

0005 8401 The subsystem status is invalid. Please call the

Support Center.

0006 1005 An error occurred. If this problem persists, please call

the Support Center.

0006 1006 An error occurred. If this problem persists, please call

the Support Center.

0006 1007 An error occurred. If this problem persists, please call

the Support Center.

0006 1008 An error occurred. If this problem persists, please call

the Support Center.

0006 1009 An error occurred. If this problem persists, please call

the Support Center.

0006 1010 An error occurred. If this problem persists, please call

the Support Center.

0006 4000 The server configuration is invalid. Please call the

Support Center.

Install the program product. E 6

Retry the same operation several times. If the

same error occurs, call the service personnel.

Call the service personnel. E 2

If nothing changes despite retrying, call the

service personnel.

Call the service personnel. E 2

E 2

0006 4002 The server configuration is invalid. Please call the

Support Center.

0007 6012 An error occurred. If this problem persists, please call

the Support Center.

0010 4005 The user ID is already logged in. Do you want to log in

forcibly?

0010 6026 The client system is illegal environment. E 2

0010 6027 An error occurred while connecting to the server.

Note: This message will not be issued when you attempt to log on.

A network error occurred, the server is not ready, or

an error occurred in the server. Note: This message might be issued when you attempt to log on.

0010 6060 A network error occurred. Failed to connect from the server due to a

0010 6070 An error occurred while connecting to the server. Failed to connect from the server due to a

0010 7060 An error occurred in the Client logic. Call the service personnel. E 2

Register the authentication data. Call the service

personnel.

E 2

Since the same user name is being used, log in

with the other user name.

You cannot connect to the server because of the

factors, such as a network error. Check the IP

address. If the IP address is correct, close the

browser (also close the browser of the storage

list), and log in again.

You cannot connect to the server because of the

factors, such as a network error. Check the IP

address. If the IP address is correct, close the

browser (also close the browser of the storage

list), and log in again.

network error etc. Check the IP address.

E 2

W 5

E 2

E 1

E 2

14 Chapter 1 Error Codes

0010 8101 The system cannot apply the new configuration. Do

you want to refresh?

Press the Refresh button, and retry the operation.

W 5

0110 5030 The displayed information has not been changed. Specify what you register, and retry the

0110 5081 The evaluation license for this product (%s) will expire

in 45days. Purchase required to continue using this product beyond the evaluation license.

0110 5082 The evaluation license for this product (%s) will expire

in 30days. Contact your sales representative to convert to a permanent license and continue use of this product.

0110 5083 The evaluation license and use of this product (%s)

will expire in %d days. You will receive no further warnings. Contact your sales representative to purchase a permanent license.

0110 5084 The evaluation license for this product (Web Console)

is not installed. Please install.

0110 5085 The total physical (raw) disk capacity of the array

exceeds the installed licensed capacity. Please install additional license key(s) to expand the license capacity of this software title.

0110 5086 The program product installation status has changed.

Try again after exit this program.

0110 5088 The maximum permissible capacity of program

product became insufficient because of the installation of PDEV.

operation.

I 5

Install Web Console program product. I 5

Please install additional license key(s) to expand the license capacity of this software title.

Log in again, and retry. I 2

Install the program product whose permissible capacity is insufficient, and retry.

W 0

I 5

0110 6027 A network error ocurred, the server is not ready, or an

error occurred in the server.

0110 6070 A network error ocurred, the server is not ready, or an

error occurred in the server.

0110 7060 An error occurred in the Client logic. Call the service personnel. E 2

0110 8100 A SIM occurred. Retry the same operation several times. If the

0110 8200 A SIM occurred. Retry the same operation several times. If the

0110 8201 The system detects an error. Retry the same operation several times. If the

0110 9100 Do you want to exit? I 0

0110 9101 Do you want to cancel? To cancel, press the OK button. I 0

0110 9102 Do you want to apply? To execute the operation in Preset, press the OK

0110 9103 Do you want to change? I 0

You cannot connect to the server because of the factors, such as a network error. Check the IP address. If the IP address is correct, close the browser (also close the browser of the storage list), and log in again.

same error occurs, call the service personnel.

button.

E 1

E 5

W 5

I 0

Hitachi Lightning 9900™ V Series Remote Console Error Codes 15

0110 9104 Do you want to change the mode? I 0

0110 9105 The value has been changed: but the server cannot

reflect the value. Do you want to exit?

0110 9106 The value has been changed: but the server cannot

reflect the value. Do you want to change the mode?

0110 9107 The value has been changed: but the server cannot

apply the value. Do you want to continue?

0190 5001 Enter the nickname. Input the nickname and retry.

0190 5002 Enter the product name. Input the product name and retry.

0190 5003 Enter the serial number. Input the serial number and retry.

0190 5004 Enter a numerical value for the serial number. Input the serial number with the numerical value

0190 5005 Enter the IP address. Input the IP address and retry.

0190 5006 Enter numerical values for the IP address. Input the IP address with the numerical value

0190 5007 Enter the location name. Input the location name and retry.

0190 5008 You cannot use the following characters: \" \\ , ; : * ? <

> | /

0190 5009 You cannot use multi-byte characters. Remove the multi-byte characters and retry.

0190 5010 This page can be accessed by the administrator only. None.

I 0

and retry.

Remove the invalid characters and retry.

0190 5011 The same nickname is already registered. Specify other nickname and register again.

0190 5012 Enter the nickname with up to 16 alphanumeric

characters.

0190 5013 Enter the product name with up to 16 alphanumeric

characters.

0190 5014 Enter the location name with up to 16 alphanumeric

characters.

0190 5015 Enter the serial no. with a number fewer than 65536. Specify the serial number with a number 65535

0190 5041 The same serial number is already registered. Specify other serial number and register again.

0190 5061 The IP address is already registered. Specify other IP address and register again.

0190 5100 The files is compressing now. After completing FDCOPY which is booted last

0190 5110 Failed to compress the trace files. If the same error occurs again despite retrying,

0190 5200 Security-file for download does not exist. Call the service personnel.

0190 5210 The number of storage devices exceeds the

maximum.

0190 6001 Failed to open the storage list file. If the same error occurs again despite retrying,

Specify the nickname using up to 16 characters

and less and retry.

Specify the product name using up to 16

characters and less and retry.

Specify the location name using up to 16

characters and less and retry.

and less, and retry.

time, retry the operation.

call the service personnel.

You cannot register anymore.

call the service personnel.

0190 6002 Failed to open the storage list file. If the same error occurs again despite retrying,

call the service personnel.

16 Chapter 1 Error Codes

0190 6003 The storage list file does not exist. Call the service personnel.

0190 6004 Failed to open the storage list file. If the same error occurs again despite retrying,

call the service personnel.

0190 6005 The storage list file does not exist. Call the service personnel.

0190 6010 The storage list file does not exist. Call the service personnel.

0190 6011 Failed to open the storage list file. If the same error occurs again despite retrying,

0190 6012 The storage list file does not exist. Call the service personnel.

0190 6013 Failed to back up the storage list file. None.

0190 6014 The user ID or password is invalid. Specify the correct password.

0190 6015 A permission error occurred. (Storage List Edit

Permission)

0190 6016 The storage list was modified by the administrator

while you were making settings.

0190 6017 The user account list was modified by the

administrator while you were making settings.

0190 6018 A permission error occurred. (Trace File Download

Permission)

0190 9000 Are you sure you want to register the storage device

entry ?

call the service personnel.

If the same error occurs again despite retrying, call the service personnel.

Reboot the process.

None.

0190 9001 Are you sure you want to delete the selected storage

device entry ?

0190 9100 Are you sure you want to compress the trace files ? None.

0210 7060 An error occurred in the Client logic. Call the service personnel. E 2

0290 5010 Enter the user ID. Specify the user ID.

0290 5014 The user ID or password is invalid. Input the correct user name or password.

0290 5015 Enter the user ID with up to 16 alphanumeric

characters.

0290 5016 The Password is invalid. Access Denied. Correct the specified content, and retry. W 5

0290 5020 The password is invalid. Input the correct password.

0290 5021 The password is invalid. Input the correct password.

0290 5022 The new password is invalid. Input the correct password.

0290 5030 You cannot use the following characters: \" \\ , ; : * ? <

> | /

0290 5040 You cannot use multi-byte characters. Remove the multi-byte characters and retry.

0290 5050 The user ID is already registered. Register the other user ID.

0290 5060 The number of user accounts exceeds the maximum. You cannot register anymore.

0290 5070 The current password is invalid. Input the password again.

None.

You can specify the user ID with up to 16 characters.

Remove the invalid characters and retry.

0290 5080 The password is invalid. Specify the correct password.

Hitachi Lightning 9900™ V Series Remote Console Error Codes 17

0290 6010 The user account list was modified by the

administrator while you were making settings.

0290 6020 The user ID was deleted by the administrator. Terminate the process.

Reopen.

0290 6030 Failed to open the user account list file. If the same error occurs again despite retrying,

call the service personnel.

0290 6040 The user account list file does not exist. Call the service personnel.

0290 6050 Failed to open the backup file of the user account list. Call the service personnel.

0290 6060 Failed to back up the user account list file. Call the service personnel.

0290 6070 Failed to restore the user account list file. Call the service personnel.

0290 6080 Failed to open the user account list file. If the same error occurs again despite retrying,

0290 6090 Failed to back up the user account list file. Call the service personnel.

0290 6100 The password is invalid. Set the correct password.

0290 6110 A permission error occurred. (User Account List Edit

Permission)

0290 6120 A permission error occurred. (User Option Panel View

Permission)

0290 6130 Failed to open the user account list file. Call the service personnel.

0290 6140 Failed to open the user account list file. If the same error occurs again despite retrying,

0290 6150 Failed to open the user account list file. If the same error occurs again despite retrying,

call the service personnel.

Call the service personnel.

call the service personnel.

0290 6160 Failed to open the user account list file. If the same error occurs again despite retrying,

0290 6170 Failed to open the user account list file. If the same error occurs again despite retrying,

0290 6180 Failed to open the user account list file. If the same error occurs again despite retrying,

0290 6190 Failed to open the environment file. If the same error occurs again despite retrying,

0290 6200 Failed to open the environment file. If the same error occurs again despite retrying,

0290 6210 Failed to open the environment file. If the same error occurs again despite retrying,

0290 6220 Failed to back up the environment file. Call the service personnel.

0290 6230 Failed to open the user account list file. Call the service personnel.

0290 6240 The user account list was modified by the

administrator while you were making settings.

0290 6250 The user account list was modified by the

administrator while you were making settings.

0290 6260 Failed to open the user account list file. If the same error occurs again despite retrying,

call the service personnel.

Terminate the process and contact the

administrator.

Terminate the process and contact the

administrator.

call the service personnel.

18 Chapter 1 Error Codes

0290 6270 Failed to open the environment file. If the same error occurs again despite retrying,

call the service personnel.

0290 6280 A permission error occurred. (User Account List Edit

Permission)

0290 6290 Failed to back up the environment file. Call the service personnel.

0290 6300 No checkbox is selected. Select the download file.

0290 9000 Are you sure you want to register the user entry ? None.

0290 9001 Are you sure you want to delete the selected user

entry ?

0290 9002 Are you sure you want to register the parameters ? None.

0290 9003 Are you sure you want to change the write permission ? None.

0290 9004 Are you sure you want to change the password ? None.

0305 6001 An error occurred. If this problem persists, please call

the Support Center.

0305 6012 An error occurred. If this problem persists, please call

the Support Center.

0305 6022 An error occurred. If this problem persists, please call

the Support Center.

0305 6023 An error occurred. If this problem persists, please call

the Support Center.

If the same error occurs again despite retrying, call the service personnel.

None.

Please reboot Remote Console, and operate again. And yet this message has been displayed, install Remote Console again.

Reboot the PC. If the error cannot be recovered, replace the PC.

E 2

0305 7060 An error occurred. If this problem persists, please call

the Support Center.

0305 7102 An error occurred. If this problem persists, please call

the Support Center.

0305 7103 An error occurred. If this problem persists, please call

the Support Center.

0305 7110 An error occurred. If this problem persists, please call

the Support Center.

0305 7201 An error occurred. If this problem persists, please call

the Support Center.

0305 7202 An error occurred. If this problem persists, please call

the Support Center.

0305 7203 An error occurred. If this problem persists, please call

the Support Center.

0305 7204 An error occurred. If this problem persists, please call

the Support Center.

(1)Please retry again.(2)Please Reboot PC. E 2

Review the configuration information and make the setting again.

Please select [OK], and then retry the operation. E 2

Collect one-touch dump/FD copy, and call the Hitachi Data Systems Support Center.

Call the service personnel. E 2

(1)Please retry again.(2)Please Reboot PC. E 2

Please select [OK], and then confirm the controller list.

Isolate problems according to the following procedure:

1. Reboot the PC.

2. Check the LAN card/LAN cable.

3. Check the IP address of the PC.

4. Replace the PC.

5. Power off/ on the DKC. (Care should be taken.)

6. When using Remote Console Server, you should check the connection between CLIENT and SERVER first. Then execute the above 1 to

5.

E 2

Hitachi Lightning 9900™ V Series Remote Console Error Codes 19

0305 7205 An error occurred. If this problem persists, please call

the Support Center.

Isolate problems according to the following

procedure:

1. Reboot the PC.

2. Check the LAN card/LAN cable.

3. Check the IP address of the PC.

4. Replace the PC.

5. Power off/ on the DKC. (Care should be

taken.)

6. When using Remote Console Server, you

should check the connection between CLIENT

and SERVER first. Then execute the above 1 to

5.

E 2

0305 7206 An error occurred. If this problem persists, please call

the Support Center.

0305 7207 An error occurred. If this problem persists, please call

the Support Center.

0305 7208 An error occurred. If this problem persists, please call

the Support Center.

Isolate problems according to the following

procedure:

1. Reboot the PC.

2. Check the LAN card/LAN cable.

3. Check the IP address of the PC.

4. Replace the PC.

5. Power off/ on the DKC. (Care should be

taken.)

6. When using Remote Console Server, you

should check the connection between CLIENT

and SERVER first. Then execute the above 1 to

5.

Isolate problems according to the following

procedure:

1. Reboot the PC.

2. Check the LAN card/LAN cable.

3. Check the IP address of the PC.

4. Replace the PC.

5. Power off/ on the DKC. (Care should be

taken.)

6. When using Remote Console Server, you

should check the connection between CLIENT

and SERVER first. Then execute the above 1 to

5.

Isolate problems according to the following

procedure:

1. Reboot the PC.

2. Check the LAN card/LAN cable.

3. Check the IP address of the PC.

4. Replace the PC.

5. Power off/ on the DKC. (Care should be

taken.)

6. When using Remote Console Server, you

should check the connection between CLIENT

and SERVER first. Then execute the above 1 to

5.

E 2

0305 7209 An error occurred. If this problem persists, please call

the Support Center.

20 Chapter 1 Error Codes

Isolate problems according to the following

procedure:

1. Reboot the PC.

2. Check the LAN card/LAN cable.

3. Check the IP address of the PC.

4. Replace the PC.

5. Power off/ on the DKC. (Care should be

taken.)

6. When using Remote Console Server, you

should check the connection between CLIENT

and SERVER first. Then execute the above 1 to

5.

E 2

0305 7210 An error occurred. If this problem persists, please call

the Support Center.

Please select [OK], and then confirm the controller list.

E 2

0310 5010 Input format of IP Address is invalid

(xxx.xxx.xxx.xxx(xxx should be from 0 to 255)).

0310 5011 0 cannot be specified in all the fields. Correct the specified content, and retry. W 5

0310 5040 The maximum of IP Address is 32. Reduce the number, and retry. W 5

0310 5041 The maximum of Community is 32. Reduce the number, and retry. W 5

0310 5050 This Community name is already in use. Check the content of the operation. W 5

0310 5051 This IP address is already in use. Check the content of the operation. W 5

0310 9060 This item will be deleted. Do you want to continue? W 5

0405 5013 An error occurred. If this problem persists, please call

the Support Center.

0405 5047 The error occurred at the time of execution of

Install/Deinstall.

0405 5070 Invalid product name. Select a valid product name. Check the product name of the selected program

0405 5071 Unable to install the license key. Temporary key

installed.

0405 5072 This subsystem is equipped with large capacity drives.

Please upgrade license.

0405 5073 To install/de-install this program product, you must

install/de-install another program product first. Program Product Name

Correct the specified content, and retry. W 5

Please call the Support Center. E 2

If the same error occurs despite retrying, call the service personnel.

product.

Purchase the official license to use this software. W 5

Order the appropriate license that meets the requirement.

Please install the related program product at first. W 5

W 5

0405 5074 The specified PP ID is invalid. Retry again. If it occurred again, call Hitachi Data

0405 5075 This key code is invalid. Confirm if the key code is correct or not. W 5

0405 5076 The serial number is incorrect. Please correct. Check the DKC Serial Number. W 5

0405 5077 To de-install this program product, you must de-install

another program product first. Program Product Name

0405 5078 To de-install this program product, you must de-install

another program product first. Program Product Name

0405 5079 This program product needs another DKC type. Please call Hitachi Data Systems Support

0405 5080 You can't change this program product for some

reason.

0405 5501 The trial days have exceeded the specified extended

days.

0405 5502 The license capacity is insufficient. The program

product is not installed.

0405 5503 You have attempted to install the Emergency key to

the option that the Permanent key has been installed. If you want to install the Emergency key forcibly by using the license key file,\\

Systems Support Center.

At first, de-install the related program product. W 5

Center.

Please call Hitachi Data Systems Support Center.

Please confirm the P.P. installation status. W 5

None W 5

If you want to install the emergency key, select the [Forcibly Install Emergency Key] check box. If you do not want to install the emergency key, clear the [Forcibly Install Emergency Key] check box.

W 5

Hitachi Lightning 9900™ V Series Remote Console Error Codes 21

nplease specify Only Normal & Warning and retry this

operation. If you want to install the Emergency key forcibly by using the licensekey code, please select [OK].

0405 6012 An error occurred. If this problem persists, please call

the Support Center.

0405 6022 A file open error has occurred. Retry again. If it occurred again, call Hitachi Data

0405 6023 An error occurred. If this problem persists, please call

the Support Center.

0405 7060 An error occurred. If this problem persists, please call

the Support Center.

0405 7061 An error occurred. If this problem persists, please call

the Support Center.

0405 7062 An error occurred. If this problem persists, please call

the Support Center.

0405 7063 An error occurred. If this problem persists, please call

the Support Center.

0405 7064 An error occurred. If this problem persists, please call

the Support Center.

0405 7101 An error occurred. If this problem persists, please call

the Support Center.

0405 7201 An error occurred. If this problem persists, please call

the Support Center.

0405 7202 An error occurred. If this problem persists, please call

the Support Center.

End other program, then re-execute the

operation.

Systems Support Center.

Reboot the PC. If It cannot be recovered, replace

the PC.

Call the service personnel. E 2

Retry again. If it occurred again, call Hitachi Data

Systems Support Center.

Call the service personnel. E 2

E 2

Order the appropriate license that meets the

requirement.

Call the service personnel. E 2

Order the appropriate license. E 2

E 2

E 4

E 2

0405 7203 An error occurred. If this problem persists, please call

the Support Center.

0405 7204 An error occurred. If this problem persists, please call

the Support Center.

0405 7205 An error occurred. If this problem persists, please call

the Support Center.

0405 7206 An error occurred. If this problem persists, please call

the Support Center.

0405 7207 An error occurred. If this problem persists, please call

the Support Center.

0405 8002 The subsystem status is invalid. Please call the

Support Center.

Order the appropriate license that meets the

requirement.

Order the appropriate license that meets the

requirement.

Please confirm the target P.P. name. E 2

Call the service personnel. E 2

Please call Hitachi Data Systems Support

Center.

Isolate problems according to the following

procedure:

1. Reboot the PC.

2. Check the LAN card/LAN cable.

3. Check the IP address of the PC.

4. Replace the PC.

5. Power off/ on the DKC. (Care should be

taken.)

E 2

22 Chapter 1 Error Codes

0405 8003 The subsystem status is invalid. Please call the

Support Center.

Isolate problems according to the following procedure:

1. Reboot the PC.

2. Check the LAN card/LAN cable.

3. Check the IP address of the PC.

4. Replace the PC.

5. Power off/ on the DKC. (Care should be taken.)

E 2

0405 8202 The subsystem status is invalid. Please call the

Support Center.

0405 8203 The subsystem status is invalid. Please call the

Support Center.

0405 8204 The subsystem status is invalid. Please call the

Support Center.

0405 8205 The subsystem status is invalid. Please call the

Support Center.

0405 8206 This program product is already used, you can't

deinstall this program.

0405 8301 The subsystem status is invalid. Please call the

Support Center.

0410 5045 The maximum number of key codes is 20. Correct the specified content, and retry. W 5

0410 5046 The maximum number of filename codes is 200. Correct the specified content, and retry. W 5

0505 6001 An error occurred. If this problem persists, please call

the Support Center.

0505 6023 An error occurred. If this problem persists, please call

the Support Center.

0505 6024 An error occurred. If this problem persists, please call

the Support Center.

Please call Hitachi Data Systems Support Center.

Stop using this program product function. W 5

Please retry this operation. E 2

Please select [OK]. E 2

Check the FD. When the failure is not recovered, reboot the PC. If it cannot be recovered, replace the PC.

E 2

0505 6025 An error occurred. If this problem persists, please call

the Support Center.

0505 6036 An error occurred. If this problem persists, please call

the Support Center.

0505 6040 An error occurred. If this problem persists, please call

the Support Center.

0505 6050 An error occurred. If this problem persists, please call

the Support Center.

0505 6502 Time out error has occurred. Please retry later. If you

still cannot perform processing, please call the technical support center.

0505 6506 Communication busy. Please retry later. Please confirm the Controller status and retry.

0505 6507 The maximum permissible capacity of program

product became insufficient because of the installation of PDEV.

Reboot SVP, and retry. E 2

Call the service personnel. E 2

Please wait for a moment and retry. W 5

Refer to SVPMSG05-30 “5. Error when operating HRC & HODM & HORC”.

Please install the program product whose maximum permissible capacity became insufficient, and retry the operation.

W 5

Hitachi Lightning 9900™ V Series Remote Console Error Codes 23

0505 7104 An error occurred. If this problem persists, please call

the Support Center.

Please call your maintenance support center to

report them with the error code.

E 2

0505 7110 An error occurred. If this problem persists, please call

the Support Center.

0505 7111 An error occurred. If this problem persists, please call

the Support Center.

0505 7201 An error occurred. If this problem persists, please call

the Support Center.

0505 7202 An error occurred. If this problem persists, please call

the Support Center.

0505 8001 The subsystem status is invalid. Please call the

Support Center.

0505 8100 An error occurred. If this problem persists, please call

the Support Center.

0505 8310 The subsystem status is invalid. Please call the

Support Center.

0505 8401 The subsystem status is invalid. Please call the

Support Center.

0510 9010 There is a charge for this operation. Do you want to

continue?

1010 1023 The specified fiber address is wrong. Correct the specified content, and issue the

Please check the inputted value and retry. E 2

Call the service personnel. E 2

Please call your maintenance support center to

report them with the error code.

Please call Hitachi Data Systems Support

Center.

Retry the same operation several times. If the

same error occurs, call the service personnel.

Retry the same operation several times. If the

same error occurs, call the service personnel.

Retry the same operation several times. If the

same error occurs, call the service personnel.

Retry the same operation several times. If the

same error occurs, call the service personnel.

W 5

request again. (Currently, Bad Value Send report

in Set Response.)

E 2

W 5

1010 1065 The specified Host Group is already used. Correct the specified contents, and request the

1010 5010 The specified LDEVs and free LUNs should be the

same number.

1010 5040 The maximum number of Paths are already set. You cannot specify anymore. W 5

1010 5041 The maximum number of LUNs is already used. The

maximum LUN number in the group is 256.

1010 5042 The maximum number of LUNs is already used. The

maximum LUN number in the port is 512.

1010 5043 The selected number of LDEVs exceeds the number

of free LUNs.

1010 5050 The specified LUN had been set. Check the content of the operation. W 5

1010 5051 The selected LUN is not a Command Device. Check the content of the operation. W 5

1010 5052 Select the LUN that is already assigned. Check the content of the operation. W 5

1010 5053 No port is specified. Check the content of the operation. W 5

1010 5054 You should map at least one path to the command

device.

1010 5055 Invalid number of LDEVs are selected to the LUN. Check the content of the operation. W 5

1010 5056 The specified LUN does not exist in the system. Check the content of the operation. W 5

setting of the configuration information again.

Correct the specified content, and retry. W 5

Reduce the number, and retry. W 5

Check the content of the operation. W 5

W 5

1010 5057 No LUN is specified. Check the content of the operation. W 5

24 Chapter 1 Error Codes

1010 5058 This item could not drag and drop to the port. Check the content of the operation. W 5

1010 5059 Duplicate fiber address. Check the content of the operation. W 5

1010 5099 The specified LUN is the last path to the Command

Device. Release the Command Device.

1010 6509 The host mode is invalid. Please specify a correct

host mode.

1010 7060 An error occurred in the Client logic. Call the service personnel. E 2

1010 9012 Security for the specified Command Device LUN will

be released. Do you want to continue?

1010 9013 The specified LUN will be assigned to Command

Device. Do you want to continue?

1010 9014 The specified LUN's Command Device attribute will be

released. Do you want to continue?

1010 9015 Are you sure you want to change the every port in

CHA into the same specification ?

1010 9017 Security will be added to the specified Command

Device LUN. Do you want to continue?

1010 9019 The specified LUN's Command Device attribute will be

released, and Command Device security will be turned off. Do you want to continue?

1010 9103 Do you want to change? I 0

1010 9150 Select the free LUN. I 0

Check the content of the operation. W 5

Correct the mode of the target group. W 0

I 0

1010 9151 Only the LUN(LDEV) is specified. Select the

corresponding LDEV(LUN).

1110 1064 The specified WWN is already in use. Correct the specified contents, and request the

1110 1065 The specified name is already in use. Correct the specified contents, and request the

1110 1110 You can not use the following characters for the

name: \ / , : ; * " < > | You cannot use spaces for the first and the last characters in the name.

1110 5000 The WWN should be input using hex digits (0-9 and

A-F) and 16 characters.

1110 5001 The name should be input using specified letters (a-z

and A-Y) and digits (0-9).

1110 5020 The Group Name should be from 1 to 8 characters. Correct the specified content, and retry. W 5

1110 5021 The name should be from 1 to 8 characters. Correct the specified content, and retry. W 5

1110 5022 Each area of the WWN should be 8 characters. Correct the specified content, and retry. W 5

1110 5040 The maximum number of Host Groups is already

registered.

1110 5041 The maximum number for WWN is already registered. Reduce the number, and retry. W 5

I 0

W 5

setting of the configuration information again.

W 5

setting of the configuration information again.

Remove the prohibited characters from the nickname.

Correct the specified content, and retry. W 5

You cannot register a host group. W 5

W 5

1110 5042 The maximum number for WWN is 255. Reduce the number, and retry. W 5

Hitachi Lightning 9900™ V Series Remote Console Error Codes 25

1110 5043 The maximum number of WWN groups is 127. Reduce the number, and retry. W 5

1110 5044 The maximum number of LUN groups is 128. Reduce the number, and retry. W 5

1110 5050 The system cannot drop the WWN on the port. W 5

1110 5051 The system cannot drop the WWN to the root. Check the content of the operation. W 5

1110 5052 The system cannot move the WWN. The specified

WWN already exists in the destination.

1110 5053 The system cannot move the WWN. The Specified

name already exists in the destination.

1110 5054 The system cannot drop the WWN on the port of

Security Switch off.

1110 5055 The LUN in the LUN Group cannot drag and drop to

the mapping window.

1110 5056 The system cannot add the LUN to the LUN group in

the mapping window.

1110 5057 The WWN group already has the same LUN group. Check the content of the operation. W 5

1110 5058 The WWN already has the same LUN group. Check the content of the operation. W 5

1110 5059 The LUN group cannot add to LUN group. Check the content of the operation. W 5

1110 5060 The system cannot add WWN to LUN group. Check the content of the operation. W 5

1110 5061 The system cannot add WWN to WWN. Check the content of the operation. W 5

1110 5062 The WWN already exists in the port. Check the content of the operation. W 5

1110 5063 The WWN already has this LUN. Check the content of the operation. W 5

1110 5064 The WWN group already contains this LUN. Check the content of the operation. W 5

Check the content of the operation. W 5

1110 5065 This name is already used on the port. Check the content of the operation. W 5

1110 7060 An error occurred in the Client logic. Call the service personnel. E 2

1110 9010 All the hosts connected to the port can access only

the LUNs defined to the group #00. If you continue this operation, the LUNs in the current group except for #00 cannot be accessed and the file system may be corrupted. Are you sure you want to continue this operation?

1110 9011 Only the host registered in the group can access the

LUNs defined to the group. If the host is not registered in the group, the host cannot access any LUN. Are you sure you want to continue this operation?

1110 9018 The Security switch of the port toggled. Do you want

to continue?

1110 9060 The specified Host Group will be deleted. Do you want

to continue?

1110 9061 The specified WWN will be deleted. Do you want to

continue?

1110 9063 Warning: The LU path to the LDEV will be released at

once. Do you want to continue?

1110 9064 Do you want to remove the WWN? I 0

I 0

26 Chapter 1 Error Codes

1110 9065 Do you want to remove all of the WWNs from the

WWN group?

1110 9066 Do you want to release the LUN from the group? I 0

1110 9067 Do you want to release the LUN group? I 0

I 0

1110 9068 Do you want to remove the LUN group with all of the

LUNs in the group?

1110 9069 The specified Command Device LUN will release

Command Device security. Do you want to continue?

1110 9080 Are you sure to clear the selected group #00? To continue prosessing, select [Yes]. To stop

1110 9100 There are different security settings in the group. Do

you want to re-configure?

1110 9101 There are some WWN groups or LUN groups that

don't have enough members. Do you want to apply?

1110 9102 Do you want to renew the security as group? I 0

2010 5030 There are no available LUSE volumes to release the

LUSE. Check the specified volumes.

2010 5031 Select the non-LUSE LDEV. Correct the specified content, and retry. W 5

2010 5032 There are no LDEVs available to set the LUSE top

volume. Check the specified LDEVs.

2010 5033 There are no LDEVs available to create the LUSE.

Check the specified LDEVs.

2010 5040 Too many LDEVs are selected for one LUSE volume.

(Max. = 36)

I 0

processing, select [No].

I 0

To execute the operation in Preset, press the OK button.

Correct the specified content, and retry. W 5

Reduce the number to 36 and less, and retry. W 5

I 5

I 0

2010 5050 No LDEV is specified. Select LDEV and retry. W 5

2010 5051 You cannot delete the first LDEV of a LUSE volume. Check the content of the operation. W 5

2010 5052 This is the last path for the LUSE volume. Check the content of the operation. W 5

2010 5053 You should map at least one path to LUSE volume. Check the content of the operation. W 5

2010 5054 The LUNs are assigned to the LDEV (or LUSE

volume).

2010 7060 An error occurred in the Client logic. Call the service personnel. E 2

2010 8100 The selected LDEV cannot set LUSE. Retry the same operation several times. If the

2010 9010 The specified volumes will be expanded to LUSE

volume. All data in each LDEV will be initialized. Do you want to continue?

2010 9060 The specified LUSE volume will be released. All data

in the volume will be initialized. Do you want to continue?

2010 9100 The LUSE volume needs at least one path. Do you

want to continue the operation?

2010 9150 Select the LUSE. I 0

2010 9151 Select the LUSE volume. I 0

Check the content of the operation. W 5

W 5

same error occurs, call the service personnel.

I 0

Hitachi Lightning 9900™ V Series Remote Console Error Codes 27

2010 9152 Warning: It is required to assign the LU Path for the

LUSE volume. Do you want to continue?

2010 9153 Select the first LDEV of the LUSE volume. I 0

I 0

3010 1046 The number of FlashAccess set exceeds the

maximum(1024).

3010 5010 The system failed the Volume to Space operation.

The specified LDEV is the last LDEV in the VDEV.

3010 5011 Specify the value over one cylinder. Correct the specified content, and retry. W 5

3010 5012 Set the value over 35MB. Correct the specified content, and retry. W 5

3010 5030 There are no LDEVs which can be initialized. Specify

LDEVs which are not CruiseControl reserved volumes.

3010 5031 No LDEV is specified. Correct the specified content, and retry. W 5

3010 5040 The specified value exceeds the maximum. W 5

3010 5050 The system failed the Volume to Space operation.

The specified LDEV is the last LDEV in the VDEV.

3010 5051 Free space is required for Install CV to operate. Check the content of the operation. W 5

3010 5052 The specified LDEV is already used. Check the content of the operation. W 5

3010 5053 The specified SSID is already used. Check the content of the operation. W 5

3010 5054 You must delete the paths associated with the LDEVs

or release the LUSE Volume or release the Reserved Volume of CruiseControl, before you delete the LDEV itself. Please try again.

Correct the specified contents, and request the

setting of the configuration information again.

Correct the specified content, and retry. W 5

Check the content of the operation. W 5

W 5

3010 5055 You cannot perform volume initialization on the

following LDEVs: Volumes with path definition, LUSE volumes, CruiseControl reserved volumes, paired volumes, and the Command Device.

3010 5056 Select LDEVs after canceling the automatically

selected LDEVs.

3010 5057 There are not enough LDEVs. Check the content of the operation. W 5

3010 7060 An error occurred in the Client logic. Call the service personnel. E 2

3010 9001 Custom volume operation is complete. I 0

3010 9010 Do you want to set the following custom volume? I 0

3010 9011 The following volume will be initialized. The stored

data in the volume will be removed at that time. Do you want to continue?

3010 9012 The following normal volume will be restored. Do you

want to continue?

3010 9019 There is no volume recovered in the specified parity

group (PG). The CVs will be deleted from the PG. Is it OK?

3010 9060 Do you want to cancel making the following custom

volume operation?

Check the content of the operation. W 5

I 0

To continue prosessing, select [OK]. To stop

processing, select [Cancel].

I 0

28 Chapter 1 Error Codes

3010 9102 Do you want to apply? To execute the operation in Preset, press the OK

button.

3010 9103 Do you want to change? I 0

3010 9150 Specify the SSID. I 0

I 0

4010 1030 Part of the range is already in use. Correct the specified content, and issue the

4010 1032 The specified value is outside the valid range. Correct the specified content, and issue the

4010 2080 Prestaging not completed. Wait for a while, and press the Refresh button,

4010 5010 The specified value is invalid for FlashAccess area.

The value should be From<To.

4010 5011 The specified value is under one cylinder. Correct the specified content, and retry. W 5

4010 5030 No deletion area is specified. Retry the operation to

specify the deletion area.

4010 7060 An error occurred in the Client logic. Call the service personnel. E 2

4010 9000 Prestaging is completed. I 0

4010 9010 The system will set the contents. I 0

4010 9060 Do you want to delete? I 0

5105 2002 An error occurred. If this problem persists, please call

the Support Center.

request again.

and then change the same configuration again. Or check the DKC status (if it is not blocked). If the same error occurs, call the service personnel.

Correct the specified content, and retry. W 5

The size of a CV which links as an expanded LU is not the same. Or you are trying to link CV and normal volume. The error does not occur normally because it is guarded in the screen. Contact the program maker.

I 0

E 6

E 2

5105 2015 A connection error has occurred. Retry the same operation. If the same error

5105 2145 A connection error has occurred. Retry the same operation. If the same error

5105 5010 An error occurred. If this problem persists, please call

the Support Center.

5105 5013 An error occurred. If this problem persists, please call

the Support Center.

5105 5099 An error occurred. If this problem persists, please call

the Support Center.

occurs despite retrying, call the service personnel.

WWN number, which is not registered, is specified. (When deleting, or changing) The error does not occur normally because it is guarded in the screen. Contact the program maker.

You are trying to perform Virtual LVI/LUN operation for a volume which LU path is set, LU expanded volume, or a volume which LDEV Security is set. The error does not occur normally because it is guarded in the screen. Contact the program maker.

You are trying to register the same host group number as the existing number. The error does not occur normally because it is guarded in the screen. Contact the program maker.

E 4

E 2

Hitachi Lightning 9900™ V Series Remote Console Error Codes 29

5105 6000 An error occurred. If this problem persists, please call

the Support Center.

If the same error occurs despite retrying, call the

service personnel.

E 2

5105 6012 An error occurred. If this problem persists, please call

the Support Center.

5105 6022 An error occurred. If this problem persists, please call

the Support Center.

5105 6023 An error occurred. If this problem persists, please call

the Support Center.

If the same error occurs despite retrying, call the

service personnel.

If the same error occurs despite retrying, call the

service personnel.

If the same error occurs despite retrying, call the

service personnel.

5105 6501 There is no monitoring data. Change the monitor switch to ON, and

accumulate the data.

5105 7111 An error occurred. If this problem persists, please call

Call the service personnel. E 2 the Support Center.

5105 7428 An error occurred. If this problem persists, please call

the Support Center.

5105 8002 The subsystem status is invalid. Please call the

Support Center.

5105 8916 An error occurred. If this problem persists, please call

the Support Center.

5105 8918 An error occurred. If this problem persists, please call

the Support Center.

5105 8919 The subsystem status is invalid. Please call the

Support Center.

5202 1231 The target volume(s) is already being used by Data

Migration.

Retry the same operation several times. If the

same error occurs, call the service personnel.

Retry the same operation several times. If the

same error occurs, call the service personnel.

Retry the same operation several times. If the

same error occurs, call the service personnel.

Retry the same operation several times. If the

same error occurs, call the service personnel.

Retry the same operation several times. If the

same error occurs, call the service personnel.

Retry the same operation. If nothing changes,

contact the service personnel.

E 2

W 5

E 2

E 6

5202 1232 The target volume(s) is already being used by

ShadowImage or ShadowImage - S/390

5202 1233 The target volume(s) is already being used by

ShadowImage or ShadowImage - S/390

5205 1076 The target volume(s) is already being used by

ShadowImage or ShadowImage - S/390

5205 1077 The target volume(s) is already being used by

ShadowImage or ShadowImage - S/390

®

.

®

.

®

.

®

.

5205 1078 The target volume is a LUSE volume. Cannot change

Retry the same operation. If nothing changes,

contact the service personnel.

Retry the same operation. If nothing changes,

contact the service personnel.

Check the status of the selected volume. E 6

Check the setting. E 6

E 6

to reserve volume.

5205 1079 The specified reserve volume has a FlashAccess

Release the FlashAccess setting. E 6 setting.

5205 1080 The target volume(s) cannot be used. Retry the same operation. If nothing changes,

E 6

contact the service personnel.

5205 1081 The target volume(s) is a command device. Release the command device, or select other

E 6

volume.

5205 1082 The target volume(s) is not equipped. Retry the same operation. If nothing changes,

E 6

contact the service personnel.

5205 1083 The target volume(s) is already reserved. Retry the same operation. If nothing changes,

E 6

contact the service personnel.

5205 1084 There is no allocable reserved volume. Set Reserve volume, and retry the operation. E 6

30 Chapter 1 Error Codes

5205 1085 The target volume(s) is already being used by

CruiseControl.

Retry the same operation. If nothing changes, contact the service personnel.

E 6

5205 1086 The RAID level of the target volume is not supported. Check the micro program version, and call the

5205 1094 The target volume is not a reserved volume. Retry the same operation. If nothing changes,

5205 1095 The number of volumes exceeds the maximum. Retry the same operation. If nothing changes,

5205 1096 The target volume(s) is already in use by HOST or

Remote Copy.

5205 1109 The target volume(s) is not supported by

CruiseControl.

5205 1117 The target volume(s) is already being used by

Concurrent Copy.

5205 1118 The target volume(s) is already being used by

Concurrent Copy.

5205 1119 The target volume(s) is already being used by

Concurrent Copy.

5205 1120 The target volume(s) is already being used by HXRC. Retry the same operation. If nothing changes,

5205 1121 The target volume(s) is already being used by HXRC. Retry the same operation. If nothing changes,

5205 1122 The target volume(s) is already being used by HXRC. Retry the same operation. If nothing changes,

service personnel.

contact the service personnel.

Retry the same operation. If nothing changes, contact the service personnel.

contact the service personnel.

E 6

5205 1207 The volume types do not match. Retry the same operation. If nothing changes,

5205 1208 The target volume(s) is not supported by

CruiseControl.

5205 1209 The target volume(s) is not supported by

CruiseControl.

5205 1210 The target volume(s) has an over flow condition. Retry the same operation. If nothing changes,

5205 1211 The number of volume pairs exceeds the maximum. Retry the same operation. If nothing changes,

5205 1212 The target volume(s) is not equipped. Retry the same operation. If nothing changes,

5205 1213 The target volume(s) cannot be used. Retry the same operation. If nothing changes,

5205 1214 The target volume is being formatted. Retry the same operation. If nothing changes,

5205 1215 The target volume(s) is a command device. Retry the same operation. If nothing changes,

5205 1216 The target volume(s) is not equipped. Retry the same operation. If nothing changes,

5205 1217 The target volume(s) cannot be used. Retry the same operation. If nothing changes,

contact the service personnel.

Retry the same operation. If nothing changes, contact the service personnel.

contact the service personnel.

E 6

Hitachi Lightning 9900™ V Series Remote Console Error Codes 31

5205 1218 The target volume is being formatted. Retry the same operation. If nothing changes,

contact the service personnel.

E 6

5205 1219 The target volume(s) is a command device. Retry the same operation. If nothing changes,

contact the service personnel.

5205 1220 The target volume is not a reserved volume. Retry the same operation. If nothing changes,

contact the service personnel.

5205 1221 The target volume(s) is already being used by

CruiseControl.

5205 1222 The number of ShadowImage or ShadowImage -

®

volume pairs exceeds the maximum.

S/390

5205 1223 The target volume(s) is already being used by

CruiseControl.

5205 1224 The target volume(s) is already being used by

CruiseControl.

5205 1225 The selected source volume and destination volume

are the same volume.

5205 1226 The target volume(s) is already being used by Remote

Copy.

5205 1227 The target volume(s) is already being used by Remote

Copy.

Retry the same operation. If nothing changes,

contact the service personnel.

Please release the ShadowImage pair. E 6

Retry the same operation. If nothing changes,

contact the service personnel.

Retry the same operation. If nothing changes,

contact the service personnel.

Retry the same operation. If nothing changes,

contact the service personnel.

Retry the same operation. If nothing changes,

contact the service personnel.

Retry the same operation. If nothing changes,

contact the service personnel.

5205 1228 The RAID level of the target volume is not supported. Retry the same operation. If nothing changes,

contact the service personnel.

5205 1229 The target volume(s) is already being used by

ShadowImage or ShadowImage - S/390

®

.

Retry the same operation. If nothing changes,

contact the service personnel.

E 6

5205 1230 The target volume(s) is already being used by

ShadowImage or ShadowImage - S/390

®

.

5205 1234 The target volume(s) is already being used by Remote

Copy.

5205 1235 The target volume(s) is already being used by Remote

Copy.

Retry the same operation. If nothing changes,

contact the service personnel.

Retry the same operation. If nothing changes,

contact the service personnel.

Retry the same operation. If nothing changes,

contact the service personnel.

5205 1236 The RAID level of the target volume is not supported. Retry the same operation. If nothing changes,

contact the service personnel.

5205 1237 The target volume(s) is already being used by

ShadowImage or ShadowImage - S/390

5205 1238 The target volume(s) is already being used by

ShadowImage or ShadowImage - S/390

®

.

®

.

5205 1239 The target volume(s) is already being used by Data

Migration.

5205 1240 The target volume(s) is already being used by

ShadowImage or ShadowImage - S/390

®

.

5205 1241 The specified migration source volume has a

FlashAccess setting.

5205 1242 The specified migration destination volume has a

FlashAccess setting.

Retry the same operation. If nothing changes,

contact the service personnel.

Retry the same operation. If nothing changes,

contact the service personnel.

Retry the same operation. If nothing changes,

contact the service personnel.

Retry the same operation. If nothing changes,

contact the service personnel.

Retry the same operation. If nothing changes,

contact the service personnel.

Retry the same operation. If nothing changes,

contact the service personnel.

5205 1243 The specified volume is not the source volume. Retry the same operation. If nothing changes,

contact the service personnel.

E 6

32 Chapter 1 Error Codes

5205 1246 The number of plan that could be executed at once is

exceeds the maximum.

Retry the same operation. If nothing changes, contact the service personnel.

E 6

5205 1247 The specified volume is already a source volume. Retry the same operation. If nothing changes,

5205 1606 The option product (CruiseControl) is not installed. Install the necessary program product. E 5

5205 2003 An internal process is being executed, or maintenance

is in progress. Please try again.

5205 2004 An error occurred. If this problem persists, please call

the Support Center.

5205 2011 The controller is busy now. Please retry a little later. E 5

5205 2024 The controller detected the blockade location. Call the service personnel. E 4

5205 2025 The controller detected the blockade location. Call the service personnel. E 4

5205 2026 The controller detected the blockade location. Call the service personnel. E 4

5205 2027 The controller detected the blockade location. Call the service personnel. E 4

5205 2028 The controller detected the blockade location. Call the service personnel. E 4

5205 2029 A data transfer failure was detected. Call the service personnel. E 4

5205 2030 A data transfer failure was detected. Call the service personnel. E 4

5205 2033 The server is now gathering the latest data. Internal

processing is being executed. Please wait a while, and then click the Refresh button.

contact the service personnel.

Confirm that maintenance operation is not in progress, and retry after a while.

The specified emulation type of CV cannot coexist. The error does not occur normally because it is guarded in the screen. Contact the program maker.

Wait for a while, and press the Refresh button. W 4

E 5

E 2

5205 3002 An error occurred. If this problem persists, please call

the Support Center.

5205 3003 An error occurred. If this problem persists, please call

the Support Center.

5205 5013 An error occurred. If this problem persists, please call

the Support Center.

5205 5099 An error occurred. If this problem persists, please call

the Support Center.

5205 6000 An error occurred. If this problem persists, please call

the Support Center.

When Virtual LVI/LUN operation (Volume Initialize) is performed, the number of volumes which should be returned to Normal Volume and the number of volumes which is requested in Volume Initialize are different. The error does not occur normally because it is guarded in the screen. Contact the program maker.

When Install CV was set, the emulation type and the specified size of the emulation type were specified incorrectly. (User specified capacity is specified to mainframe volume. The user specified number of cylinders is specified to open volume.) The error does not occur normally because it is guarded in the screen. Contact the program maker.

You are trying to perform LUN Security operation for a port where LUN Security function is invalid. The error does not occur normally because it is guarded in the screen. Contact the program maker.

You are trying to set an expanded LU which includes an already expanded LU. The error does not occur normally because it is guarded in the screen. Contact the program maker.

If the same error occurs despite retrying, call the service personnel.

E 2

Hitachi Lightning 9900™ V Series Remote Console Error Codes 33

5205 6001 An error occurred. If this problem persists, please call

the Support Center.

If the same error occurs despite retrying, call the

service personnel.

E 2

5205 6012 An error occurred. If this problem persists, please call

the Support Center.

5205 6022 An error occurred. If this problem persists, please call

the Support Center.

5205 6023 An error occurred. If this problem persists, please call

the Support Center.

5205 6036 An error occurred. If this problem persists, please call

the Support Center.

5205 6501 There is no monitoring data. Change the monitor switch to ON, and

5205 6502 Now processing. Please wait a while, and then retry

the operation.

5205 7400 Failed to get information from hihsmatm.ini. Retry the same operation several times. If the

5205 7401 Failed to get information from hihsmpln.ini. Retry the same operation several times. If the

5205 7402 Failed to get information from hihsmfpg.ini. Retry the same operation several times. If the

5205 7403 Failed to get information from hihsmcls.ini. Retry the same operation several times. If the

5205 7404 Failed to get information from hihsmpgr.ini. Retry the same operation several times. If the

If the same error occurs despite retrying, call the

service personnel.

If the same error occurs despite retrying, call the

service personnel.

If the same error occurs despite retrying, call the

service personnel.

E 2

accumulate the data.

Retry the same operation several times. If the

same error occurs, call the service personnel.

E 2

I 5

I 0

E 4

5205 7405 Failed to get information from hihsmldv.ini. Retry the same operation several times. If the

5205 7406 Failed to get configuration information. Retry the same operation several times. If the

5205 7407 Cannot make proper migration plan by this function. Retry the same operation several times. If the

5205 7408 There is not enough valid monitoring data in the

specified term.

5205 7409 Failed to write to hihsmpln.ini. Retry the same operation several times. If the

5205 7410 Failed to write to hihsmpgr.ini. Retry the same operation several times. If the

5205 7411 Failed to write to hihsmldv.ini. Retry the same operation several times. If the

5205 7412 It cannot make auto migration plan(Parameter error). Retry the same operation several times. If the

5205 7413 Invalid data from hihsmpln.ini. Retry the same operation several times. If the

5205 7414 Invalid data from hihsmpgr.ini. Retry the same operation several times. If the

5205 7415 Invalid data from hihsmcls.ini. Retry the same operation several times. If the

same error occurs, call the service personnel.

Retry the same operation several times. If the

same error occurs, call the service personnel.

E 4

34 Chapter 1 Error Codes

5205 7416 Invalid data from hihsmpgr.ini. Retry the same operation several times. If the

same error occurs, call the service personnel.

E 4

5205 7417 Invalid data from hihsmldv.ini. Retry the same operation several times. If the

5205 7418 Invalid configuration information. Retry the same operation several times. If the

5205 7419 Invalid reserve volume information. Retry the same operation several times. If the

5205 7420 There is not enough valid CruiseControl data in the

specified term. Please check the following items: (1)Sampling Term [Time], (2)Monitoring term.

5205 7421 Cannot make proper migration plan by this function.

Please check the following items: (1)Reserve volume location. (2)Auto migration threshold disk utilization.

5205 7422 A memory allocation error occurred. Retry the same operation several times. If the

5205 7423 An internal error occurred. Retry the same operation several times. If the

5205 7424 Failed to delete all plans. Retry the same operation several times. If the

5205 7426 Failed to delete plan. Retry the same operation several times. If the

5205 8001 An error occurred while connecting to the subsystem.

Please retry a little later.

same error occurs, call the service personnel.

Retry the same operation several times. If the same error occurs, call the service personnel.

same error occurs, call the service personnel.

Retry the same operation several times. If the same error occurs, call the service personnel.

E 4

E 6

5205 8100 This function is not supported. E 6

5205 8102 This function is not supported. Retry the same operation several times. If the

5210 5010 There is no monitoring data. Change the monitor switch to ON, and

5210 9010 The history will be updated. Do you want to continue? I 0

5210 9060 The plan will be deleted. Do you want to continue? I 0

5210 9061 The specified instructions will be reset. Do you want to

continue?

5210 9100 Do you want to get the latest monitoring data? I 0

5210 9319 Do you want to cancel plan(s) ? You should select the

apply at once.

5305 1064 The specified WWN is already in use. Correct the specified contents, and request the

5305 1258 This port is not equipped. Retry the same operation. If nothing changes,

5305 2002 An error occurred. If this problem persists, please call

the Support Center.

5305 2015 A connection error has occurred. Retry the same operation. If the same error

same error occurs, call the service personnel.

accumulate the data.

I 0

setting of the configuration information again.

contact the service personnel.

Failed to connect the communication between DKCs (SVPs). If the same error occurs despite retrying, call the service personnel.

occurs despite retrying, call the service personnel.

E 6

W 5

E 6

E 2

E 3

Hitachi Lightning 9900™ V Series Remote Console Error Codes 35

5305 2033 The server is now gathering the latest data. Internal

processing is being executed. Please wait a while, and then click the Refresh button.

Wait for a while, and press the Refresh button. W 3

5305 2145 A connection error has occurred. Retry the same operation. If the same error

5305 3003 An error occurred. If this problem persists, please call

the Support Center.

5305 5000 The WWN should be input with hex digits (0-9 and A-

F) and 16 characters.

5305 5010 An error occurred. If this problem persists, please call

the Support Center.

5305 5013 An error occurred. If this problem persists, please call

the Support Center.

5305 5018 Invalid value. Enter correct value(0-65535). W 6

5305 5099 An error occurred. If this problem persists, please call

the Support Center.

5305 5101 The target WWN is not registered. Check the specified content, and retry. W 6

occurs despite retrying, call the service

personnel.

When LUSE is set, the maximum number of

instructions, which DKC can set, was exceeded.

The error does not occur normally because it is

guarded in the screen. Contact the program

maker.

Correct the specified content, and retry. E 2

You are giving operation command to a parity

group, which is not installed in Virtual LVI/LUN

operation. The error does not occur normally

because it is guarded in the screen. Contact the

program maker.

Retry the same operation. If the same error

occurs, call the service personnel.

You are trying to set multiple paths from a group

to the same volume. The error does not occur

normally because it is guarded in the screen.

Contact the program maker.

E 3

E 2

5305 5102 The target PA group(s) is not registered. Check the specified content, and retry. W 6

5305 5104 The target PA group(s) is already reserved. Check the specified content, and retry. W 6

5305 5105 The target port(s) does not equip the monitored

WWN(s).

5305 5106 The target WWN is already registered in the port. Check the specified content, and retry. W 6

5305 5107 The specified Name is already used. Check the specified content, and retry. W 6

5305 5108 The specified Name is already used. Check the specified content, and retry. W 6

5305 5109 The number of WWN(s) that is monitored exceeds the

maximum in the port.

5305 5110 The number of WWN(s) that is monitored exceeds the

maximum.

5305 5111 The number of WWN(s) that is monitored exceeds the

maximum in the PA group.

5305 5112 The target WWN belongs to the PA group Check the specified content, and retry. W 6

5305 5113 The target WWN belongs to the PA group Check the specified content, and retry. W 6

5305 5114 The target WWNs have different attributes. Check the specified content, and retry. W 6

5305 6000 An error occurred. If this problem persists, please call

the Support Center.

Check the specified content, and retry. W 6

If the same error occurs despite retrying, call the

service personnel.

E 2

5305 6012 An error occurred. If this problem persists, please call

the Support Center.

36 Chapter 1 Error Codes

If the same error occurs despite retrying, call the

service personnel.

E 2

5305 6022 A file open error has occurred. If the same error occurs despite retrying, call the

service personnel.

E 2

5305 6023 A file access error has occurred. If the same error occurs despite retrying, call the

5305 6036 An error occurred. If this problem persists, please call

the Support Center.

5305 6050 An error occurred. If this problem persists, please call

the Support Center.

5305 6051 An error occurred. If this problem persists, please call

the Support Center.

5305 7111 An error occurred. If this problem persists, please call

the Support Center.

5305 7428 An error occurred. If this problem persists, please call

the Support Center.

5305 8002 The subsystem status is invalid. Please call the

Support Center.

5305 8918 An error occurred. If this problem persists, please call

the Support Center.

5305 8919 The subsystem status is invalid. Please call the

Support Center.

5307 5102 The target PA group(s) is not registered. Check the specified content, and retry. W 6

5307 5128 The number of PA group(s) exceeds the maximum. Check the specified content, and retry. I 6

service personnel.

If the same error occurs despite retrying, call the service personnel.

Call the service personnel. E 2

Retry the same operation several times. If the same error occurs, call the service personnel.

E 2

5310 1110 You can not use the following characters for the

name: \ / , : ; * " < > | You cannot use spaces for the first and the last characters in the name.

5310 5000 The WWN should be input using hex digits (0-9 and

A-F) and 16 characters.

5310 5067 Upper value is not set in the non-priority port. Set the upper limit of the non-prioritized port. W 5

5310 5068 The value is not set in the all control. Set the value of the entire conrol. W 5

5310 5069 Upper value is not set in the non-priority WWN. Set the upper limit of the non-prioritized port. W 5

5310 5106 Target WWN is already registered in the port. Check the specified content, and retry. I 5

5310 5107 The specified name is already used. Check the specified content, and retry. I 5

5310 5108 The specified name is already used. Check the specified content, and retry. I 5

5310 5109 The number of WWN(s) that is monitored exceeds the

maximum in the port.

5310 5110 The number of WWN(s) that is monitored exceeds the

maximum.

5310 5111 The number of WWN(s) that is monitored exceeds the

maximum in the PA group.

5310 5128 The number of PA group(s) exceeds the maximum. Check the specified content, and retry. I 5

Remove the prohibited characters from the nickname.

Correct the specified content, and retry. W 5

Check the specified content, and retry. I 5

W 5

5310 5129 Target WWN is already registered in another PA

group.

Check the specified content, and retry. I 5

Hitachi Lightning 9900™ V Series Remote Console Error Codes 37

5310 5133 The WWN that belongs to the PA Group is not

deleted.

5310 5134 The attribute of WWN is different from the PA group. Set the attribute together. W 5

Delete the WWN from PA Group first. W 5

5310 5135 The WWN should be input with hex digits(0-9 and A-

F) and 16 characters. And PA name should be specified letters(a-z and A-Y) and digits(0-9).

5310 5136 This WWN is already registered as the different

Nickname.

5310 7427 Configuration information is not correct. Please call

Support Center.

5310 9077 Are you sure you want to delete the WWN? I 5

5310 9078 Are you sure you want to delete the PA group? I 5

5310 9079 The PA group was deleted because there are no more

WWNs in the group.

5310 9312 The port control changed. W 5

5310 9313 The WWN control changed. W 5

5310 9314 There is no control, because the upper value is 0 in all

ports.

5310 9315 Monitoring switch is off. Please change the short

range switch.

6005 5013 An error occurred. If this problem persists please call

Support Center.

6005 5099 An error occurred. If this problem persists, please call

the Support Center.

Check the contents and retry. W 5

Check the content, and retry. W 5

Retry the same operation several times. If the

same error occurs, call the service personnel.

I 5

W 5

I 5

Retry the same operation. If nothing changes,

call the service personnel.

You are trying to set multiple volumes from a

port/group to pair of ID/LUN. The error does not

occur normally because it is guarded in the

screen. Contact the program maker.

E 2

6005 6012 An error occurred. If this problem persists please call

Support Center.

6005 6023 An error occurred. If this problem persists please call

Support Center.

6005 8000 A time-out error occurred. Retry the operation. If you get the same

6005 8001 A time-out error occurred. Retry the operation. If you get the same

6005 8100 A time-out error occurred. Retry the operation. If you get the same

6005 8700 Please retry operation. Retry the operation. I 4

6005 8701 Logical Path between the MCU and the RCU is not

active.

If nothing changes despite retrying, call the

service personnel.

If nothing changes despite retrying, call the

service personnel.

message again, reboot the PC. If necessary,

please call the Hitachi Data Systems Support

Center.

message again, reboot the PC. If necessary,

please call the Hitachi Data Systems Support

Center.

message again, reboot the PC. If necessary,

please call the Hitachi Data Systems Support

Center.

A logical path does not exist between the MCU

and the RCU. Check the path status on RCU

Status screen, and reestablish the paths with

Edit Path.

E 2

E 4

I 4

38 Chapter 1 Error Codes

6005 8702 The pair status of the M-VOL is not valid. The pair status is not a permissible type for this

operation. Renew and check the screen. If the MVOL status permits the operation, retry the operation.

I 4

6005 8703 The specified number of Path is less than the

minimum number of Paths on RCU Option screen.

6005 8704 The specified number of Paths is less than the

minimum number of Paths on RCU Option screen. This is a result of a communication error between MCU and RCU.

6005 8705 The path could not be deleted due to a

communication error between MCU and RCU.

6005 8706 Parameter specified by Remote Copy operation is

invalid.

6005 8707 Parameter specified by DataMigration operation is

invalid.

6005 8708 The pair status of the R-VOL is not valid. Check the pair status for TrueCopy. If the

The number of paths is less than the minimum number specified on the RCU Option screen. Check the number of paths, establish the minimum number of paths, and retry the operation.

A communication error occurred between the MCU and the RCU. Check the path status on RCU Status screen, and re-establish the paths with Edit Path.

Either a communication error occurred between the MCU and the RCU, or the CHA has become blocked. Please contact the Hitachi Data Systems Support Center.

A parameter specified by the TrueCopy operation is invalid. For example, the R-VOL that is specified could already be in use as the R-VOL of another TrueCopy pair.

A parameter specified by the data migration operation is invalid. (For example, the R-VOL that is specified may already be in use as the RVOL of another pair.) Please check the status of the volumes and retry the operation.

requested R-VOL is in a permissible status, please retry the operation.

I 4

W 4

I 4

6005 8709 Remote Copy operation was rejected. All channel adapters are not active for TrueCopy.

6005 8710 The pair status of the specified volume is not valid. The pair status does not permit this operation.

6005 8711 Parameter specified by Remote Copy operation for

expansion volume is not valid.

6005 8712 The operation was rejected because of a FREEZE

state.

6005 8713 The port group exists on the specified port. The port type could not be changed because the

Please contact the Hitachi Data Systems Support Center.

Verify the pair status, and if the operation is permitted retry.

A parameter specified by TrueCopy operation for the expansion volume is not valid. For example, the specified Port /ID/LUN of the R-VOL may be invalid. Verify that the Port /ID/LUN is the RCU. Please establish the correct parameter and retry the operation.

1. If this was a path operation retry after the problem has been fixed.

2. If this was a pair operation, retry after the paths have been recovered. Two means of recovering paths are as follows: (a) Execute ESTPATH from the host console, or (b) First delete the path(s) from the SVP, then readd them.

port group was set in the specified package. Delete the group setting and then change the port type.

E 4

I 4

E 4

Hitachi Lightning 9900™ V Series Remote Console Error Codes 39

6005 8714 An internal error occurred. The command to delete the RCU is rejected

because there is at least one pair established in

the RCU. Delete the pair(s) that apply to that

RCU and then retry the delete RCU operation.

E 4

6005 8715 Invalid number of paths. The specified number of paths is not within the

acceptable path range of 0 to 4. Please verify the

number of paths and retry the operation.

6005 8716 Specified port is not RCP. Check the configuration of the LCP/RCP, then

6005 8717 Invalid Destination Link Address. The specified logical address must be either 00

6005 8718 The specified logical path already exists. The specified link address and port are already in

6005 8719 Invalid RCU serial number, SSID, Link Address or

Controller ID.

6005 8720 Too many RCUs. (Four RCUs allowed). A maximum of four RCUs are permitted, and that

6005 8721 Path establishing is not complete. Check the path connections between the MCU

6005 8722 Path establishing failed. Check the path connections between the MCU

6005 8723 The Edit Path operation was rejected because the

specified path is the last path of some Remote Copy pairs.

either specify the correct port or change the port

to RCP.

or 01. Check the logical address and retry the

operation.

use. Check all existing logical path addresses,

and specify another link address or RCP port.

Check the serial number, SSID and link address

of the RCU, and set the correct value. Then retry

the operation. If the same error occurs, contact

the Hitachi Data Systems Support Center.

many already exist.

and the RCU, then retry the operation.

Add another path, or delete all pairs on the RCU.

Then retry the operation.

E 4

I 4

E 4

I 4

E 4

I 4

6005 8724 Specified number of Path is less than the Minimum

Paths on RCU Option screen.

6005 8725 Currently running microprogram version does not

support the specified operation.

6005 8726 Multi platform feature already installed in MCU. The multiplatform feature has already been

6005 8727 The number of minimum paths is more than the

number of normal paths.

6005 8728 The number of minimum paths is more than the

number of normal paths.

6005 8729 An internal error occurred. An internal error has occurred. Please call the

The specified number of paths is less than the

minimum number of paths specified on the RCU

Option panel.

The 9900V microcode version does not support

the specified function or operation. Please

contact the Hitachi Data Systems Support

Center.

installed in the MCU. Please verify the

configuration of the MCU.

If the error code is 100c, please set the minimum

number of paths after adding the normal path(s).

If the error code is 400c, please delete the paths

after adding them, or delete the paths after

decreasing the number of minimum paths.

If the error code is 100c, please set the minimum

number of paths after adding the normal path(s).

If the error code is 400c, please delete the paths

after adding them, or delete the paths after

decreasing the number of minimum paths.

Hitachi Data Systems Support Center.

I 4

E 4

40 Chapter 1 Error Codes

6005 8730 Invalid Logical Addresses are specified. 1. If you are adding RCUs, specify the same

logical address.

2. If you are editing paths, specify the same logical address as the existing paths. (Refer to the Edit Path Screen.)

I 4

6005 8731 The existing logical addresses are not equal. The logical addresses of all existing paths are

6005 8732 Too many SSIDs(Only Four SSIDs are allowed). The maximum number of SSIDs (four) has been

6005 8733 The Fibre-Remote Copy function is not installed in the

specified MCU.

6005 8734 The Fibre-Remote Copy function is not installed in the

specified RCU.

6005 8735 Invalid RCU serial number, SSID, Link Address or

Controller ID.

6005 8736 The specified RCU or SSID contains some Remote

Copy volume pairs.

6005 8737 An internal error occurred. An internal error has occurred. Please call the

6005 8738 Remote Copy is not supported under the MCU

Controller emulation type.

not the same. Delete the RCU, then re-add it, using the same logical address as other existing paths.

entered. Verify that the SSIDs are valid, delete one or more, and then retry the operation.

Please install the program product key in the MCU.

Please install the program product key in the RCU.

Check the serial number, SSID and link address of the RCU, and set the correct value. Then retry the operation. If the same error occurs, contact the Hitachi Data Systems Support Center.

Invalid serial number or SSID for this operation. Either the RCU is not a proper machine type for TrueCopy, or the RCU's controller is not the proper type for data migration. Check the serial number and SSID of the RCU, and set the correct value.

Hitachi Data Systems Support Center.

The emulation type of the MCU does not support TrueCopy. If you want to use TrueCopy, please call the Hitachi Data Systems Support Center.

I 4

E 4

I 4

E 4

I 4

E 4

I 4

6005 8739 NVS status of MCU is not active. The MCU NVS status specified by the host is not

6005 8740 NVS status of RCU is not active. The RCU NVS status specified by the host is not

6005 8741 The logical paths between the MCU and RCU are not

established.

6005 8742 Pinned track(s) exists on the M-VOL. Check the status of the M-VOL tracks, and clear

6005 8743 Pinned track(s) exists on the R-VOL. Check the status of the R-VOL tracks, and clear

active. Set the NVS to “on” for the MCU, using any attached host, then retry the operation.

active. Use any attached host to set the NVS to “on” for the MCU, then retry the operation.

Check the path status between the MCU and the RCU.

the pinned tracks.

I 4

W 4

Hitachi Lightning 9900™ V Series Remote Console Error Codes 41

6005 8744 The specified M-VOL condition is not valid for Remote

Copy.

The M-VOL is not available for the requested

operation, because of one or more of the

following reasons:

1. The volume is blocked.

2. The volume is under maintenance.

3. The volume is copying data (correction copy or

drive copy).

4. The volume is correction access condition.

Check the logical device status of the specified

M-VOL. If the M-VOL is either under

maintenance or is copying data, retry the

operation after the process is completed.

W 4

6005 8745 The R-VOL is already in use by another system. The specified R-VOL is already in use. Examples

6005 8746 Remote Copy is not supported under the M-VOL

Device emulation type.

6005 8747 Currently running microprogram version does not

support the specified operation.

6005 8748 Specified M-VOL may be in use by HOST. Data migration cannot start because the volume

6005 8749 Specified R-VOL is still online from HOST. Please check if the input number of R-VOL is

include:

1. The R-VOL is already being used by Dual

Copy.

2. The R-VOL is already being used for

TrueCopy operations.

3. The R-VOL is already being used by pprc or

TrueCopy.

4. The R-VOL is already being used by

Concurrent Copy.

5. The R-VOL is reserved.

6. The R-VOL already being used by

ShadowImage. Check the R-VOL status of the

RCU from either the host or the SVP.

The emulation type of the M-VOL does not

support TrueCopy. If you want to use TrueCopy,

please call the Hitachi Data Systems Support

Center.

The version of the microcode on the subsystem

does not support the specified function or

operation. Please contact the Hitachi Data

Systems Support Center.

is online. Please vary the path offline and retry.

correct. If not, enter the correct R-VOL number. If

the number is correct, please vary the specified

path offline.

I 4

6005 8750 DataMigration is not supported under the MCU

Controller emulation type.

6005 8751 Remote Copy is not supported under the RCU

Controller emulation type, or the CT Group is not usable.

6005 8752 DataMigration is not supported under the RCU

Controller type.

6005 8753 An internal error occurred. An internal error has occurred. Please call the

6005 8754 Invalid MCU serial number or MCU SSID. Check the serial number or SSID of MCU, then

The RCU controller emulation type does not

support data migration. Please contact the

Hitachi Data Systems Support Center.

Add Pair operation failed.

1. Confirm the controller emulation type, and

refer to the manual.

2. Confirm the CT Group number in the MCU.

The RCU controller emulation type does not

support data migration. Please contact the

Hitachi Data Systems Support Center.

retry with correct parameter.

42 Chapter 1 Error Codes

I 4

E 4

6005 8755 Invalid RCU serial number or RCU SSID. Check the serial number or SSID of RCU, then

retry with correct parameter.

E 4

6005 8756 MCU Subsystem Cache status is not active. Check the subsystem cache status of the MCU

6005 8757 One side of MCU Cache is blocked. Please contact the Hitachi Data Systems Support

6005 8758 Unexpected error occurred on MCU. Please contact the Hitachi Data Systems Support

6005 8759 RCU Subsystem Cache status is not active. Please contact the Hitachi Data Systems Support

6005 8760 M-VOL and R-VOL Track Formats do not match. Check the track formats of the specified M-VOL

6005 8761 M-VOL with R-VOL device emulation combinations

are not supported.

6005 8762 R-VOL Device Cache status is not active. Check the device cache status of R-VOL from

6005 8763 R-VOL DFW status is not active. Check the DFW status of the R-VOL from the

6005 8764 The Specified R-VOL is not usable. The specified R-VOL is not usable because of

from the host. If it is off, set it on and retry. If it cannot be set on, please contact the Hitachi Data Systems Support Center.

Center.

and R-VOL.

Check the device type of the specified M-VOL and R-VOL.

host. If it is off, set it on and retry. If it cannot be set on, please contact the Hitachi Data Systems Support Center.

one or the following reasons:

1. The specified volume has not been installed.

2. The specified volume is defined as a command device for Command Control Interface (CCI).

I 4

W 4

I 4

W 4

6005 8765 DataMigration is not supported under the M-VOL

Device emulation type.

6005 8766 Remote Copy is not supported under the R-VOL

Device emulation type.

6005 8767 DataMigration is not supported under the R-VOL

Device emulation type.

6005 8768 The RCU is still in other Remote Copy condition. The RCU containing the R-VOL is being used as

6005 8769 The RCU is still in other Remote Copy condition. The RCU containing the R-VOL is being used as

6005 8770 The Cache on the MCU is automatically recovering.

Please wait a few minutes then retry again.

The device emulation type of the specified MVOL does not support data migration. Please contact the Hitachi Data Systems Support Center.

The device emulation type of the R-VOL does not support TrueCopy. Please contact the Hitachi Data Systems Support Center.

The R-VOL device emulation type does not support data migration. Please contact the Hitachi Data Systems Support Center.

the RCU for TrueCopy. Verify the status of the RCU, if necessary delete the RCU, then retry the operation.

the RCU for TrueCopy. Verify the status of the RCU.

Select [OK] to acknowledge the message, then retry the operation after the cache has been recovered.

I 4

E 4

I 4

Hitachi Lightning 9900™ V Series Remote Console Error Codes 43

6005 8771 R-VOL option change operation failed. Only M-VOL

option was modified because RCU side did not support a fence level displaying function.

The R-VOL option change operation failed (only

the M-VOL option was modified), because the

RCU side does not support the display fence

level function.

I 4

6005 8772 Pair option change operation failed because a

communication error has occurred or R-VOL status is invalid.

6005 8773 Pair option change was refused because M-VOL is

suspended.

6005 8774 Multi platform feature already installed in MCU. The multiplatform feature has already been

6005 8775 Multi platform feature already installed in RCU. The multiplatform feature has already been

6005 8776 The M-VOL is already used by another system. The M-VOL is already being used by another

6005 8777 Combination of MCU with RCU controller type is not

supported.

6005 8778 One side of Cache on RCU is blocked. There is an invalid cache status on the RCU.

The pair option change operation failed, either

because a communication error occurred or

because the R-VOL status is not valid. Please

verify the status.

Resume the pair for the M-VOL, then retry the

operation.

installed in the MCU. Please verify the

configuration of the MCU.

installed in the RCU. Please verify the

configuration of the RCU.

operation. Possibilities include:

1. The M-VOL is already used by TrueCopy.

2. The M-VOL is already used by ShadowImage.

Check the M-VOL status of the MCU from the

host or the SVP.

Check the controller type of the specified MCU

and RCU, then call the Hitachi Data Systems

Support Center.

Check the status and recover the cache, then

retry the operation.

E 4

I 4

W 4

6005 8779 TrueCopy is not supported under the RCU controller

type.

6005 8780 TrueCopy – S/390® function is not installed in

specified controller.

6005 8781 TrueCopy – S/390® function is not installed in

specified controller.

6005 8782 DataMigration function is not installed in specified

controller.

6005 8783 The Remote Copy Semi-Sync function is not installed

in specified controller(s).

6005 8784 The Remote Copy Semi-Sync function is not installed

in specified controller(s).

6005 8785 The M-VOL is defined as the expansion volume. Please recheck the volume. I 4

6005 8786 The R-VOL is defined as the expansion volume. Please recheck the volume. I 4

6005 8787 The specified RCU does not support the Remote

Copy for the expansion volume.

6005 8788 The specified expansion volume (Port/Group/LUN) is

not defined in the RCU.

This controller type does not support TrueCopy

operations.

The TrueCopy option must be installed in the

MCU and RCU before an TrueCopy volume pair

can be created.

The TrueCopy option must be installed in the

MCU and RCU before an TrueCopy volume pair

can be created.

The data migration option must be installed in

the specified MCU before a data migration pair

can be created.

If nothing changes despite retrying, call the

service personnel.

If nothing changes despite retrying, call the

service personnel.

The controller type or the microprogram version

of the specified RCU does not support TrueCopy

for the expansion volume.

Verify the port ID and LUN ID of the expansion

volume in the RCU.

I 4

44 Chapter 1 Error Codes

6005 8789 Combination of the specified expansion volumes is

not valid.

The combination of the specified volumes for LUN Expansion is not valid. Verify the parameters and retry the operation.

I 4

6005 8790 The specified expansion volume (Port/Group/LUN) of

the RCU is not usable.

6005 8791 The specified M-VOL is still online from another

HOST.

6005 8792 Archival function is not installed in specified

controller(s).

6005 8793 The TrueCopy function is not installed in specified

controller(s).

6005 8794 The TrueCopy function is not installed in specified

controller(s).

6005 8795 The M-VOL should have ShadowImage-

®

/ShadowImage Split pair(PSUS) status when

S/390 defined as T-VOL. It should not be Reserve VOL, nor ShadowImage-S/390

®

/ShadowImage Reverse Copy

status.

6005 8796 The R-VOL should not be ShadowImage-

®

/ShadowImage T-VOL, Reserve VOL, nor

S/390 ShadowImage-S/390

®

/ShadowImage Reserve Copy

status.

The specified expansion volume (Port/ID/LUN) of the RCU is not usable. For example,

1. The specified expansion volume of the RCU is blocked.

2. The specified expansion volume of the RCU is in CC=3 condition.

3. The specified expansion volume of the RCU requires intervention.

4. The specified RCU does not support TrueCopy for the expansion volume.

Please vary the concerned path offline from the other host, and then retry the operation.

Install the Archival function in the MCU and the RCU, then retry the operation.

Install TrueCopy in the MCU and the RCU, then retry the operation.

Check the status of the specified M-VOL from the host or the SVP.

Check the status of the specified R-VOL from the host or the SVP.

I 4

6005 8797 The M-VOL should be the ShadowImage-

®

S/390

/ShadowImage T-VOL of the pair established,

Check the status of the specified M-VOL from the host or the SVP.

I 4

with one S-VOL to one T-VOL.

6005 8798 The MCU is already used by ShadowImage-

®

/ShadowImage.

S/390

The Add Pair operation failed because the MCU is already being used by ShadowImage. Verify

I 4

the status of the MCU and retry the operation.

6005 8799 The M-VOL is already in use by CruiseControl. Verify the status of the specified M-VOL. E 4

6005 8800 The R-VOL is already in use by CruiseControl. Verify the status of the specified R-VOL. E 4

6005 8801 The R-VOL is reserved, or the RCU or the path

between MCU-RCU is in a heavy load condition.

6005 8802 CT group is not active. The add pair operation failed because the C/T

Verify the status of the specified R-VOL. If the device is not reserved, retry the operation.

I 4

E 4 Group is not active. Add the C/T group, then retry the operation.

6005 8803 Too many RCUs in this CT Group. The add pair operation failed because there are

I 4 too many RCUs in this C/T group. If the timer type is System, then 4 RCU have already been added. If the timer type is Local or None, then 1 RCU has already been added.

Hitachi Lightning 9900™ V Series Remote Console Error Codes 45

6005 8804 Copy mode cannot be changed. The resume pair operation failed. The volume

and the copy mode must be either both asynchronous or both synchronous. Verify that the status of the volume and the copy mode match, then retry the operation.

I 4

6005 8805 CT Group is not active in the RCU. The resume pair operation failed, because there

is no R-VOL in the C/T Group. Verify the status of the C/T group in the MCU/RCU. If an M-VOL exists, delete it and retry the add pair operation.

6005 8806 CT Group Option cannot be changed unless deleting

or suspending all asynchronous pairs in the group.

If you want to change the C/T group option (timer type or time out), either delete all asynchronous pairs in the group, or verify the status of the RCU C/T Group option and set the same option as the MCU.

6005 8807 Too many MCUs in this CT Group. The add pair operation failed because there are

too many MCUs in this C/T group. If the timer type is System, then 4 MCUs have already been added. If the timer type is local or none, then 1 MCU has already been added.

6005 8808 Please retry. Add Pair(Paircreate)/Resume

Pair(Pairresync) operation after waiting a few minutes.

The add/resume pair operation failed, because the either the specified volume or another volume in the same group is being changed to simplex or suspend status. Retry the operation after the status change is completed.

6005 8809 Please wait. Retry Add Pair(Paircreate)/Resume

Pair(Pairresync) operation in a few minutes.

Add/resume pair operation failed. The specified volume or another volume in the same group being changed to simplex/suspend status in RCU. A few minutes later, please renew and check the TrueCopy screen and if specified volume is in a permissible status please retry the operation.

I 4

6005 8810 TrueCopy – S/390® Asynchronous function is not

installed in specified RCU.

6005 8811 This version does not support multiple CT Groups in

the RCU.

6005 8812 This version does not support combining TrueCopy –

®

S/390

Asynchronous pairs and Synchronous pairs in

the DKC subsystems(s).

6005 8813 Specified M-VOL is a ShadowImage-

®

S/390

/ShadowImage volume. This version does not

support it.

6005 8814 Specified R-VOL is a ShadowImage-

®

/ShadowImage volume. This version does not

S/390 support it.

6005 8815 TrueCopy Asynchronous function is not installed in

specified RCU.

Install TrueCopy Asynchronous in the RCU and retry the operation.

This microcode version does not support multiple C/T groups in the RCU. Verify the status and retry.

The add pair operation failed. This version does not support intermix of TrueCopy Asynchronous pairs and Synchronous pairs in the same DKC. Refresh the screen and confirm the Copy Mode in the MCU and RCU.

This microcode version does not support ShadowImage, and the specified M-VOL is a ShadowImage volume. Verify the status of the MVOL and retry.

This microcode version does not support ShadowImage, and the specified R-VOL is a ShadowImage volume. Verify the status of the R-VOL and retry.

Install the TrueCopy Asynchronous function in the RCU, then retry the operation.

I 4

46 Chapter 1 Error Codes

6005 8816 Add Pair(Paircreate) operation failed because

combining TrueCopy – S/390

®

Asynchronous pairs and TrueCopy Asynchronous pairs is not allowed in the same CT Group.

The operation failed because TrueCopy asynchronous pairs cannot be mixed with TrueCopy asynchronous pairs. Verify the status, then retry the operation.

I 4

6005 8817 Preset Suspension is effective in the CT Group. Cancel the preset suspension in the C/T group,

then retry the operation.

6005 8818 Preset Suspension is effective in the CT Group. Cancel the preset suspension in the C/T group,

then retry the operation.

6005 8819 The specified R-VOL is in an intervention-required

Check the status of the specified R-VOL. W 4

condition.

6005 8820 The specified R-VOL is not in a permissible condition

for Remote Copy operations.

The TrueCopy operation failed, because R-VOL has one of the following conditions:

1. The volume is blocked.

2. The volume is under maintenance.

3. The volume is copying data (correction copy or drive copy).

4. The volume is in the correction access condition.

6005 8821 The specified R-VOL is not recognizable from the

Verify the configuration of the specified R-VOL. W 4

connection port.

6005 8822 I/O Error occurred on the R-VOL. Check the SSB log, record the error number, and

call the Hitachi Data Systems Support Center.

6005 8823 The TrueCopy – S/390® Periodic Differential Copy

function is not installed in the specified MCU.

If the TrueCopy-S/390® PeriodicCopy function is not installed in MCU of the microprogram version, install the appropriate version. If the program product is not installed in MCU, install the microprogram.

6005 8824 The TrueCopy – S/390® Periodic Differential Copy

function is not installed in the specified RCU.

If the TrueCopy-S/390® PeriodicCopy function is not installed in RCU of the microprogram version, install the appropriate version. If the program product is not installed in MCU, install the microprogram.

I 4

W 4

E 4

I 4

6005 8825 The Add Pair (Paircreate)/Resume (Pairresync)

operation failed combining pairs (using Fibre path and

Refresh and confirm the TrueCopy screen in the MCU and RCU.

I 4

Serial path) is not allowed in the same CT Group.

6005 8826 An internal error occurred. An internal error has occurred. Please call the

E 4

Hitachi Data Systems Support Center.

6005 8827 Please wait a few minutes and retry the Add

Pair(Paircreate)/Resume Pair(Pairresync).

The Add Pair (Paircreate) /Resume Pair (Pairresync) operation failed. A few minutes later,

I 4

please refresh the screen, confirm if the specified volumes are in the permissible status, and then retry the operation.

6005 8828 This version of the microprogram does not support

combining pairs using Fibre paths, with pairs using

Confirm the path type specified for the Paircreate operation on the RCU Status screen.

I 4

Serial paths in the same DKC subsystem.

6005 8829 The LCP of the RCU cannot access the specified R-

VOL.

Take the following actions:

1. Specify only one CU# for the same LCP of the

E 4

RCU.

2. Connect to the LCP that can access the specified R-VOL.

6005 8830 The specified M-VOL is already used as a

CruiseControl Reserve VOL.

Check the status of the specified M-VOL (P-VOL) from HOST or SVP.

I 4

Hitachi Lightning 9900™ V Series Remote Console Error Codes 47

6005 8831 The specified R-VOL is already used as a

CruiseControl Reserve VOL.

Check the status of the specified R-VOL (S-VOL) from HOST or SVP.

I 4

6005 8832 Please wait a few minutes and retry the Add Pair

(Paircreate) / Resume Pair (Pairresync) operation.

6005 8833 Please wait a few minutes and retry the Add Pair

(Paircreate) / Resume Pair (Pairresync) operation.

6005 8834 The Add Pair (Paircreate) operation failed because

you tried to create volume pairs which exceeded the licensed capacity.

6005 8835 The Add Pair (Paircreate) operation failed because

you tried to create volume pairs which exceeded the licensed capacity of the RCU side.

6005 8836 No additional volume pairs waiting for copy. Please check the pair status and retry. I 4

6005 8837 An internal error occurred. An internal error has occurred. Please call the

6005 8838 Specified volume is not part of a Remote Copy pair. The specified volume is not part of a TrueCopy

6005 8839 Invalid RCU serial number, SSID, Link Address or

Controller ID.

Please check the status of the specified M-VOL (P-VOL), and then retry the Add Pair (Paircreate) / Resume Pair (Pairresync) operation in a few minutes.

Please check the status of the specified R-VOL (S-VOL), and then retry the Add Pair (Paircreate) / Resume Pair (Pairresync) operation in a few minutes.

Refer to the license key and confirm the licensed capacity of the volumes. If you need to create more pairs, purchase a license key that allows you to use a larger capacity.

Refer to the license key of the RCU side, and confirm the licensed capacity of the volumes. If you need to create more pairs, purchase a license key that allows you to use a larger capacity.

Hitachi Data Systems Support Center.

pair. Please check the volume.

Check the serial number, SSID and link address of the RCU, and set the correct value. Then retry the operation. If the same error occurs, contact the Hitachi Data Systems Support Center.

I 4

E 4

I 4

E 4

6005 8840 Suspend(Pairsplit-r) operation is not valid for R-VOL. Suspend mode is not valid for the R-VOL. Check

6005 8841 Invalid R-VOL. Please check the R-VOL status. E 4

6005 8842 R-VOL status change failed after M-VOL status

change. Confirm R-VOL status.

6005 8843 Suspend(Pairsplit-r) operation failed because

specified volume or other volume in the same group is not in permissible status.

6005 8844 Suspend(Pairsplit-r) operation failed because

specified volume or other volume in the same group is in status transition.

6005 8845 Preset Suspension is effective in the CT Group. Cancel the preset suspension in the C/T group,

the volume and retry.

Confirm the R-VOL status. E 4

The operation failed, because of one of the following reasons:

1. The specified volume is simplex.

2. There is no duplex or duplex-pending volume in the group.

3. Either the specified volume or another volume in the same group are suspended. Verify the status, and retry the operation.

The operation failed, because of one of the following reasons:

1. The specified volume or another volume in the same group are deleting.

2. The specified volume or another volume in the same group are suspending. Wait for the change in status to be completed, then retry the operation.

then retry the operation.

I 4

48 Chapter 1 Error Codes

6005 8846 An internal error occurred. An internal error has occurred. Please call the

Hitachi Data Systems Support Center.

E 4

6005 8847 An internal error occurred. An internal error has occurred. Please call the

6005 8848 Please wait a few minutes and retry the Suspend

Pair(Pairsplit-r) operation.

6005 8849 Specified volume is not part of Remote Copy pair (Not

in Duplex(PAIR), Pending(COPY), Suspend(PSUS) state).

6005 8850 Invalid RCU serial number, SSID, Link Address or

Controller ID.

6005 8851 Invalid R-VOL. Please check the R-VOL status. E 4

6005 8852 R-VOL status change failed after M-VOL status

change. Confirm R-VOL status.

6005 8853 DataMigration volume pair cannot be terminated

because migration copy is in progress and the specified volume may be online from HOST.

6005 8854 Delete Pair(Pairsplit-S) operation failed because M-

VOL is in Simplex(SMPL) status.

Hitachi Data Systems Support Center.

The suspend pair (Pairsplit-r) operation failed. A few minutes later, please refresh the screen, confirm if the specified volumes are in the permissible status, and then retry the operation.

The specified volume is not part of a TrueCopy pair. Please check the volume.

Check the serial number, SSID and link address of the RCU, and set the correct value. Then retry the operation. If the same error occurs, contact the Hitachi Data Systems Support Center.

Confirm the R-VOL status. E 4

Data migration could not be started. Check the status of the volume, because the specified volume may be online, or migration copy may be in progress.

The operation failed, because of one of the following reasons:

1. The specified volume is simplex.

2. There is no duplex or duplex-pending or suspend volume in the group. Verify the status, and retry the operation.

E 4

I 4

E 4

I 4

6005 8855 Delete(Pairsplit-S) operation failed because specified

volume or other volume in the same group is in status transition.

6005 8856 Delete Pair(Pairsplit-S) operation failed because

Consistency Time of CT Group is not determined by SEQCHK.

6005 8857 Some volumes were not deleted by the Delete

Pair(Pairsplit-S) operation.

6005 8858 All volumes were not deleted by the Delete

Pair(Pairsplit-S) operation.

The operation failed, because of one of the following reasons:

1. The specified volume or another volume in the same group are deleting.

2. The specified volume or another volume in the same group are suspending. Wait for the change in status to be completed, then retry the operation.

The operation failed, because the status of the C/T Group is SEQCHK. Retry the operation with either the volume or the group option.

The operation failed for one or more of the volumes, because either the pair status of the volume is SEQCHK or the consistency time of the volume does not match the consistency time of the C/T group. Verify the status of the failed volumes. If necessary, retry the delete pair operation with the volume or the group option.

The operation failed for all of the volumes, because either the pair status of the volume is SEQCHK or the consistency time of the volume does not match the consistency time of the C/T group. Verify the status of the failed volumes. If necessary, retry the Delete Pair operation with the volume or the group option.

I 4

Hitachi Lightning 9900™ V Series Remote Console Error Codes 49

6005 8859 Delete Pair(Pairsplit-S) operation with C/T option

failed because some R-VOLs in the group are in Duplex(PAIR) or Pending(COPY) status.

Select [OK] to continue the operation without shut down of the connected SCSI host(s). Select [Cancel] if you need to terminate the operation and shut down the host(s).

I 4

6005 8860 An internal error occurred. An internal error has occurred. Please call the

Hitachi Data Systems Support Center.

6005 8861 An internal error occurred. An internal error has occurred. Please call the

Hitachi Data Systems Support Center.

6005 8862 Please wait a few minutes and retry the Delete

Pair(Pairsplit-S) operation.

6005 8863 Unknown Error Code. The Remote Console PC detected an unknown

6005 8864 An internal error occurred. An internal error has occurred. Please call the

6005 8865 An internal error occurred. An internal error has occurred. Please call the

6005 8866 An internal error occurred. An internal error has occurred. Please call the

6005 8867 An internal error occurred. An internal error has occurred. Please call the

6005 8868 Duplicate CT Group#(A CT Group has been already

active in MCU).

The delete pair (Pairsplit-S) operation failed. A few minutes later, please refresh the screen, confirm if the specified volumes are in the permissible status, and then retry the operation.

error code. Please call the Hitachi Data Systems Support Center.

Hitachi Data Systems Support Center.

The operation failed because a duplicate C/T Group is already active in the MCU. Verify the status of the C/T group and retry the operation.

E 4

I 4

E 4

6005 8869 CT Group is not active. Verify that the C/T group is active in the MCU. E 4

6005 8870 CT Group Option cannot be changed unless all

asynchronous pairs in the group are suspended or deleted.

6005 8871 The TrueCopy – S/390® Asynchronous function is not

installed in specified MCU.

6005 8872 This version does not support multi CT Groups in the

MCU.

6005 8873 TrueCopy Asynchronous function is not installed in

specified MCU.

6005 8874 Invalid Timer Type option. Specify "Local" or "None" for the timer type on

6005 8875 At least one asynchronous pair is active in this group. Renew and check the TrueCopy screen. E 4

6005 8876 There are no PCBs which corresponds to the

specified port type.

6005 8877 An internal error occurred. An internal error has occurred. Please call the

6005 8878 CT Group is not active. Verify that the C/T group is active in the MCU. E 4

6005 8879 At least one asynchronous pair is active in this group. Verify that there are no active asynchronous

The group operation failed because the specified group has at least one asynchronous pair. Renew and check the TrueCopy screen.

Install TrueCopy Asynchronous in the MCU and retry the operation.

This microcode version does not support multiple C/T Groups in the MCU. Verify the status and retry the operation.

Install the TrueCopy Asynchronous function in the MCU, then retry the operation.

the TrueCopy panel, then retry the operation.

Confirm the PCB type and try the operation again with a correct parameter.

Hitachi Data Systems Support Center.

pairs in this group, and retry the operation.

I 4

E 4

I 4

50 Chapter 1 Error Codes

6005 8880 Please wait. Retry Delete Group operation in a few

minutes.

Retry the operation after the pair status has been changed to simplex.

I 4

6005 8881 An internal error occurred. An internal error has occurred. Please call the

6005 8882 Asynchronous Option (Current Pending Update Data

Rate) cannot be changed, because the CT group is active.

6005 8883 An internal error occurred. An internal error has occurred. Please call the

6005 8884 An internal error occurred. An internal error has occurred. Please call the

6005 8885 An internal error occurred. An internal error has occurred. Please call the

6005 8886 An internal error occurred. An internal error has occurred. Please call the

6005 8887 An internal error occurred. An internal error has occurred. Please call the

6005 8888 An internal error occurred. An internal error has occurred. Please call the

6005 8889 The specified port is not equipped. Refresh the screen, and retry. If nothing

6005 8890 The specified port is being initialized. Please wait until the initialization of the port

Hitachi Data Systems Support Center.

Delete all of the TrueCopy C/T groups, then retry the operation.

Hitachi Data Systems Support Center.

changes, call the Hitachi Data Systems Support Center.

ends, and retry the operation.

E 4

I 4

E 4

6005 8891 Logical paths exist on the MCU port. Please delete the logical paths on the specified

port and retry the operation.

6005 8892 R-VOLs exist on the RCU port. Are you sure you want

to continue this operation?

6005 8893 An internal error occurred. An internal error has occurred. Please call the

6005 8894 Pending background data exists on the MCU. Please stop the jobs from the host and retry the

6005 8895 Pending background data exists on the RCU. Please stop the jobs from the host and retry the

6005 8896 Parameter error has occurred. Refresh the screen, and retry. If nothing

6005 8897 LUs exist on the port. Please delete the LUs defined on the port and

6005 8898 Pending data exists on the port. Add another path, or delete all pairs on the RCU.

6005 8899 An internal error occurred. An internal error has occurred. Please call the

6005 8900 An error occurred during the port change. Please call the Hitachi Data Systems Support

If you want to continue this operation, select [Yes] . If not, select [No].

Hitachi Data Systems Support Center.

operation.

changes, call the Hitachi Data Systems Support Center.

retry the operation.

Then retry the operation.

Hitachi Data Systems Support Center.

Center.

E 4

W 4

E 4

I 4

E 4

6005 8901 An error occurred during the port change. Please call the Hitachi Data Systems Support

Center.

E 4

Hitachi Lightning 9900™ V Series Remote Console Error Codes 51

6005 8902 An error occurred during the port change. Please call the Hitachi Data Systems Support

Center.

E 4

6005 8903 Unknown Error Code. The Remote Console PC detected an unknown

error code. Please call the Hitachi Data Systems Support Center.

6005 8904 The Remote Copy Function Switch bit No. 5 in MCU is

on, although the difference management areas in MCU are full.

Check the difference management instruction for other pair in MCU, and decide which instruction the target pair chooses. After that, perform the following. -When creating the target pair by the track, create after recreating the other pair by the cylinder. -When creating the target pair by the cylinder, create by performing the difference management instruction in cylinder, or turning off the bit #5 of the switch for MCU remote copy function.

6005 8905 The extended SM is not equipped in MCU. Install SM to MCU with the installation instruction

of SM for remote copy extension (Install TrueCopy Function).

6005 8906 The Remote Copy Function Switch bit No. 5 in MCU is

on, although the difference management areas in RCU are full.

Check the difference management instruction for other pair in RCU, and decide which instruction the target pair chooses. After that, perform the following. -When creating the target pair by the track, create after recreating the other pair by the cylinder. -When creating the target pair by the cylinder, create by performing the difference management instruction in cylinder, or turning off the bit #5 of the switch for MCU remote copy function.

E 4

E 5

6005 8907 The extended SM is not equipped in RCU. Install SM to RCU with the installation instruction

E 5 of SM for remote copy extension (Install TrueCopy Function).

6005 8908 Invalid parameter. Please check the value of the specified

I 4 parameter and retry.

6005 8909 A Port exchange error occurred. The Remote Console PC detected a port

E 4 exchange error. Please contact the Hitachi Data Systems Support Center.

6005 8910 A Port exchange error occurred. The Remote Console PC detected a port

E 4 exchange error. Please contact the Hitachi Data Systems Support Center.

6005 8911 Logical paths exist on the port. The Remote Console PC detected a logical path

®

) on the port. Please delete the path(s)

(S/390

I 4

and retry the operation.

6005 8912 Logical paths exist on the port. The Remote Console PC detected a logical path

®

) on the port. Please delete the path(s)

(S/390

I 4

and retry the operation.

6005 8913 Invalid port type. Please check the port status and retry. W 4

6005 8914 Multi platform feature already installed in subsystem. The multiplatform feature has already been

I 4 installed in the subsystem. Please verify the configuration of the subsystem.

6005 8915 The port type exchange operation is rejected because

the host(s) is(are) processing the port type exchange.

Check the port status, and retry the operation once the port type has been exchanged.

E 4

6005 8917 Too many pairs in this CTG. Register a new CT group, and register the

ASYNC pair.

52 Chapter 1 Error Codes

W 0

6007 6012 An error occurred. If this problem persists, please call

the Support Center.

6010 5010 The Priority value is invalid. Specify the correct value. Correct the specified contents, and retry. W 5

6010 5011 The Range value is invalid. Specify the correct value. Correct the specified contents, and retry. W 5

If nothing changes despite retrying, call the service personnel.

E 2

6010 5012 The Error Level value is invalid. Specify the correct

value.

6010 5013 The Fence value is invalid. Specify the correct value. Correct the specified contents, and retry. W 5

6010 5014 The Force value is invalid. Specify the correct value. Correct the specified contents, and retry. W 5

6010 5015 The R-VOL Write value is invalid. Specify the correct

value.

6010 5016 The Split-r/Suspend kind value is invalid. Specify the

correct value.

6010 5017 The Update value is invalid. Specify the correct value. Correct the specified contents, and retry. W 5

6010 5030 The displayed information has not been changed. Specify what you register, and retry. W 0

6010 5034 There are no RCUs in the CU. Please try again after

registering RCUs.

6010 5035 There are no CT groups for the asynchronous Remote

Copy. Please try again after registering CT groups.

6010 5066 The RCU and one of the CT group channel types do

not match. Please correct RCU or CT group.

6010 5131 The combination of parameters which you specified is

not permitted. Please specify the parameters by a different combination.

6010 5137 The Operation value is invalid. Specify the correct

value.

Correct the specified contents, and retry. W 5

Register a CT group, and retry. W 5

Select the same path type for RCU and CT group.

Check the condition for setting parameter, and reexecute the setting.

Check the contents, and retry. W 0

W 5

I 5

6010 5138 The Rate value is invalid. Specify the correct value

from 1 to 546.

6010 5139 The Script File Name value is invalid. Specify the

correct value.

6010 7060 An error occurred in the Client logic. Call the service personnel. E 2

6010 7301 An error occurred in the Client logic. Call the service personnel. E 2

6010 7302 An error occurred in the Client logic. Call the service personnel. E 2

6010 7303 An error occurred in the Client logic. Call the service personnel. E 2

6010 8101 The system cannot apply the new configuration. Do

you want to refresh?

6010 9003 Snapshot has failed. If nothing changes despite retrying, call the

6010 9004 Snapshot is done. Normal end. I 0

6010 9006 Exchange the channel cable connections after your

confirmation of the port type.

6010 9007 Please confirm the specified R-VOLs are varied off-

line.

6010 9008 SIMs of Remote Copy are cleared. Normal end. I 0

Check the contents, and retry. W 0

Press the Refresh button, and retry. W 5

W 0

service personnel.

The same as the message. W 5

The same as the message. W 0

Hitachi Lightning 9900™ V Series Remote Console Error Codes 53

6010 9021 The Port Setting process has not completed. Do you

want to continue for other ports?

To continue the process, select OK. After the process, reexecute the setting for the port which is not in operation.

W 5

6010 9022 WARNING: Initial copy mode 'None' is selected for

some volume pairs. Are you sure that the M-VOL and the R-VOL of these pairs are already synchronized?

6010 9023 Are you sure you want to output pair status into a

snapshot file? (Warning: Snapshot file will be overwritten.)

6010 9024 Are you sure you want to exchange the specified ports

?Please confirm the concerned channel paths are offline.

6010 9025 Are you sure you want to exchange the specified ports

?The concerned paths should be deleted before the operation.

6010 9070 Are you sure you want to delete the specified RCUs? If you want to delete the specified RCU, select

6010 9071 Are you sure you want to delete the paths of a

specified RCU?

6010 9072 Are you sure you want to delete the specified volume

pairs?

6010 9073 Are you sure you want to suspend the specified

volume pairs?

6010 9074 Are you sure you want to erase data on the R-VOL? If you want to delete the contents of the remote

Check the contents of the main and remote volumes. If the contents match, select OK. If not, select Cancel.

If you reexecute snapshot by overwriting the existing snapshot, select OK. If you need to migrate the existing snapshot, select Cancel. And retry after the migration.

The same as the message. W 5

OK. If not, select Cancel.

If you want to delete the specified path, select OK. If not, select Cancel.

If you want to delete the specified pair, select OK. If not, select Cancel.

If you want to suspend the specified pair, select OK. If not, select Cancel.

volume, select OK. If not, select Cancel.

W 0

I 0

6010 9075 Are you sure you want to delete the SSIDs of a

specified RCU?

6010 9076 Are you sure you want to delete the specified CT

groups?

6010 9100 Do you want to exit? If you want to exit the screen, select OK. If not,

6010 9101 Do you want to cancel? To cancel, press the OK button. I 0

6010 9102 Do you want to apply? To execute the operation in Preset, press the OK

6010 9103 Do you want to change? Not used. I 0

6010 9104 Do you want to change the mode? If you want to switch the mode, select OK. If not,

6010 9105 The value has been changed: but the server cannot

reflect the value. Do you want to exit?

6010 9106 The value has been changed: but the server cannot

reflect the value. Do you want to change the mode?

6010 9107 The value has been changed: but the server cannot

apply the value. Do you want to continue?

6010 9111 Do you want to omit? If you want to destroy the setting data, select OK.

If you want to delete the specified SSID, select OK. If not, select Cancel.

If you want to delete the specified CT group, select OK. If not, select Cancel.

select Cancel.

button.

select Cancel.

If you want to exit the screen by destroying the setting data, select OK. If not, select Cancel.

If you want to switch the View mode by destroying the setting data, select OK. If not, select Cancel.

If you want to refresh the screen by destroying the setting data, select OK. If not, select Cancel.

If not, select Cancel.

I 0

W 0

54 Chapter 1 Error Codes

6010 9112 Do you want to continue this operation? If you want to continue the current operation,

select OK. If not, select Cancel.

I 0

6010 9113 Are you sure you want to clear SIMs of Remote Copy. If you want to clear the remote copy related SIM,

6010 9114 The value has been changed. Do you want to

continue the operation?

6010 9154 As the result of this operation, you will not be able to

re-start ERASE R-VOL operation. To delete the pair forcibly, please try again with 'Force' option.

6010 9300 WARNING: Destination volume of specified volume

pair may contain some inconsistency, because volume copy is not completed yet. Full volume initialization is required before re-using it.

6010 9301 WARNING: Through this operation, M-VOL status will

be changed to SMPL status forcibly, but R-VOL status will not be changed. If you do this operation, please change the R-VOL status to SMPL later.

6010 9302 There are no RCP ports. Set the port to RCP before registering RCU. W 0

6010 9303 There are no valid volumes. There is no valid volume. Check the device

6010 9304 WARNING: ""Group" "or ""C/T"" is specified for Delete

Range. Confirm all pairs in the group are synchronized. If some volumes are not synchronized, full volume initializations are required before re-using them.

select OK. If not, select Cancel.

If you want to continue the process, select OK. If not, select Cancel.

The same as the message. W 0

emulation and the definition of the SCSI path (for TrueCopy).

The same as the message. W 0

W 0

I 0

W 0

6010 9305 There are no initiator ports. Set the port to Initiator before registering RCU. W 0

6010 9306 The Remote Copy function is not installed in this

controller. You cannot create pairs.

6010 9307 You specified the same volumes more than once. The

duplicate occurrences were excluded.

6010 9308 You set same path more than once. The same paths

are excluded.

6010 9309 All paths which you set have already been registered.

This operation will finish forcibly because there is no paths which can be added.

6010 9310 You set the same SSID more than once. The

duplicate SSIDs are excluded.

6010 9311 All SSIDs which you set have already been registered.

This operation will finish forcibly because there is no SSID which can be added.

6010 9316 Through this operation, M-VOL status will be changed

to Simplex mode even if the M-VOL is online to the host.

There is no remote copy license. Set the license. W 0

Since the same volume where multiple paths are defined was selected, the overlapped one was eliminated. Press the OK button and continue.

Since there were overlapped paths in the added paths, the overlapped ones were eliminated. Press the OK button and continue.

Since all the added paths are overlapped, the operation of adding paths cannot be executed. Press the OK button and continue.

Since there were overlapped SSIDs in the added SSIDs, the overlapped ones were eliminated. Press the OK button, and continue.

Since all the added SSIDs are overlapped, the operation of adding SSIDs cannot be executed. Press the OK button, and continue.

The same as the message. W 0

W 0

Hitachi Lightning 9900™ V Series Remote Console Error Codes 55

6010 9317 The destination volume of the specified volume pair

may contain some inconsistency because volume copy is not completed yet. Full volume initialization is required before re-using it.

The same as the message. W 0

6010 9318 As the result of this operation, you will not be able to

re-start ERASE R-VOL operation.

7005 5013 An error occurred. If this problem persists please call

Support Center.

7005 5099 An error occurred. If this problem persists, please call

the Support Center.

7005 6012 An error occurred. If this problem persists please call

Support Center.

7005 6023 An error occurred. If this problem persists please call

Support Center.

7005 8000 A time-out error occurred. Retry the operation. If you get the same

7005 8001 A time-out error occurred. Retry the operation. If you get the same

7005 8100 A time-out error occurred. Retry the operation. If you get the same

If you want to delete a pair, even though you cannot reexecute the P-VOL deletion, select OK. If not, select Cancel.

E 2

You are trying to set paths to un-installed volume/volume other than the top of an expanded LU/Reserve volume of CruiseControl. The error does not occur normally because it is guarded in the screen. Contact the program maker.

E 2

message again, reboot the PC. If necessary, please call the Hitachi Data Systems Support Center.

W 0

E 2

E 4

7005 8525 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

7007 6012 An error occurred. If this problem persists, please call

the Support Center.

7007 7111 An error occurred. If this problem persists, please call

the Support Center.

7010 5115 The volume of S-VOL is different from specified P-

VOL.

7010 5116 You cannot create another L1 pair, because the

number of L1 pairs exceeds the maximum.

7010 5117 No MU number is available. You cannot create the specified pair. Check the

7010 5118 The MU number is not selected. Select MU number. W 0

7010 5119 No P-VOL is selected. Select P-VOL, and operate. W 0

7010 5120 No S-VOL is selected. Select S-VOL, and operate. W 0

E 2

Check the capacity of P-VOL and S-VOL. Specify a volume with the same capacity, and retry the operation.

You cannot create L1 pair for the specified PVOL. Delete the created L1 pair, and retry the operation.

possible number of pairs to be created.

W 0

56 Chapter 1 Error Codes

7010 5121 The data has been changed. If you select another tab

(page), the settings will be discarded. Are you sure you want to change the pages?

7010 5122 No data has been changed. Go on to the next operation. W 0

7010 5123 The password is invalid. Check the password. W 0

Apply the data in the Preset Volume List. To stop the transaction, press OK and continue the operation.

W 0

7010 5124 You cannot select more than one operation at a time. Multiple volumes cannot be processed in the

operation. Process one volume at a time.

7010 5125 No target volume is selected. Select the target volume. W 0

7010 5126 You cannot create another L2 pair, because the

number of L2 pairs exceeds the maximum.

7010 5127 The specified MU number is invalid. Select another

MU number.

7010 6502 Currently processing. Wait a few minutes and then

retry the operation.

7010 6503 The target volume status is being changed to SMPL. Wait for a while, and retry the operation. I 0

7010 6504 The number of L1 pairs exceeds the maximum. You cannot create L1 pair for the specified P-

7010 6505 The number of L2 pairs exceeds the maximum. You cannot create L2 pair for the specified P-

7010 7310 Unregistered error code. Contact Hitachi Data Systems Support Center. W 0

7010 7311 The settings could not be applied. Wait for a while, and retry the operation. If the

You cannot create L2 pair for the specified PVOL. Delete the created L2 pair, and retry the operation.

Select the other MU number. I 0

Wait for a while, and retry the operation. I 0

VOL. Delete the created L1 pair, and retry the operation.

VOL. Delete the created L2 pair, and retry the operation.

same error occurs despite retrying, contact Hitachi Data Systems Support Center.

W 0

I 0

W 0

7010 7312 The password could not be acquired. Contact Hitachi Data Systems Support Center. W 0

7010 7313 The details on the error could not be acquired. Contact Hitachi Data Systems Support Center. W 0

7010 8001 A time-out error occurred. Retry the operation. If you get the same

7010 8500 The program product is not installed. Check if the necessary key for the program

7010 8501 The command was rejected, because a status

transition was in progress.

7010 8502 You cannot reserve the volume, because a remote

copy pair exists in the same subsystem frame.

7010 8503 You cannot create the new pair, because a remote

copy pair exists in the same subsystem frame.

7010 8504 The command was rejected. You cannot execute the operation with the

7010 8505 The requested command is invalid. Contact Hitachi Data Systems Support Center. I 0

7010 8506 The command was rejected. The specified S-VOL is

being used from the host or by a TrueCopy volume.

message again, reboot the PC. If necessary, please call the Hitachi Data Systems Support Center.

product is installed.

Wait for a while, and retry the operation. I 0

Delete the Remote Copy pair. I 0

current pair status. Check the pair status.

Change the specified S-VOL to other volume, or stop using the S-VOL in the host or TrueCopy, and then retry the operation.

E 4

I 0

Hitachi Lightning 9900™ V Series Remote Console Error Codes 57

7010 8507 The Pairsplit command was issued to the pairs in a

PSUS status.

You cannot execute the Pairsplit command because the pair is already in the PSUS status.

I 0

7010 8508 The Paircreate command was issued to the pairs in a

PSUS status.

7010 8509 The Split command with the QUIESCE specification

was issued to a secondary boot device.

7010 8510 The M-VOL Suspend command was issued to a

secondary boot device.

7010 8511 You cannot reserve the volume, because a path group

is set.

7010 8512 You cannot perform the Resync or Suspend

operation, because a path group is set.

7010 8513 The command was rejected. The specified P-VOL is

being used from the host or by Remote Copy.

7010 8514 No reserved volume can be allocated. Delete the Reserve volume. I 0

7010 8515 The number of cylinders in the reserved volume

exceeds the maximum.

7010 8516 The number of P-VOL cylinders exceeds the

maximum.

7010 8517 The number of S-VOL cylinders exceeds the

maximum.

7010 8518 You cannot create a pair, because the track format is

different for each. Make sure that the specified emulation type is the same for both.

You cannot execute the Pairsplit command because the pair is already in the PSUS status.

I 0

Detach the S-VOL from the host, or delete the TrueCopy path.

Change the specified P-VOL to other volume, or stop using the P-VOL in the host or TrueCopy, and then retry the operation.

I 0

Check the emulation type. I 0

I 0

7010 8519 You cannot set a pair because the number of

cylinders is different for each. Make sure that the capacity is the same for both.

7010 8520 You cannot set a pair, because the volume type is

different for each.

7010 8521 The number of multiple copy jobs exceeded the

maximum.

7010 8522 The emulation type of the P-VOL is not supported. Specify the emulation type supported in

7010 8523 The emulation type of S-VOL is not supported. Specify the emulation type supported in

7010 8524 The emulation type is not supported. Specify the emulation type supported in

7010 8525 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

7010 8526 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

7010 8527 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

7010 8528 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

7010 8529 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

7010 8530 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

Check the volume capacity. I 0

Specify the volume of the same emulation type, and retry the operation.

I 0

ShadowImage.

I 0

58 Chapter 1 Error Codes

7010 8531 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

7010 8532 The P-VOL and S-VOL are being used from the host

or by Remote Copy.

7010 8533 The emulation type of the specified reserved volume

is not supported.

7010 8534 An internal logical contradiction occurred. Contact Hitachi Data Systems Support Center. I 0

7010 8535 A processor failure was detected. Contact Hitachi Data Systems Support Center. I 0

7010 8536 A cache failure was detected. Contact Hitachi Data Systems Support Center. I 0

7010 8537 The cache capacities do not match. Contact Hitachi Data Systems Support Center. I 0

7010 8538 An SM failure was detected. Contact Hitachi Data Systems Support Center. I 0

7010 8539 There is insufficient shared memory to create 4096

pairs.

7010 8540 There is sufficient shared memory to create 4096

pairs, but initial subsystem setup is required before creating pairs.

7010 8541 There is sufficient shared memory to create 4096

pairs, and the initial subsystem setup is complete.

7010 8542 Failed to complete the initial shared memory setup. Contact Hitachi Data Systems Support Center. I 0

7010 8543 The shared memory size is different. Contact Hitachi Data Systems Support Center. I 0

7010 8544 16 Mbytes of shared memory are available. I 0

Check the target volume, or stop using it in Remote copy.

Specify the volume of the supported emulation type.

There is insufficient shared memory in DKC. Contact Hitachi Data Systems Support Center.

Contact Hitachi Data Systems Support Center. I 0

I 0

7010 8545 A power supply failure is detected. Contact Hitachi Data Systems Support Center. I 0

7010 8546 The command was rejected. The PS OFF is in

progress.

7010 8547 A data transfer failure is detected (CHA). Contact Hitachi Data Systems Support Center. I 0

7010 8548 A data transfer failure is detected (DKA). Contact Hitachi Data Systems Support Center. I 0

7010 8549 The P-VOL is not implemented. You cannot execute the operation for the volume

7010 8550 The P-VOL cannot be used. Contact Hitachi Data Systems Support Center,

7010 8551 The P-VOL is being formatted. Wait until the volume is formatted, and retry the

7010 8552 The P-VOL is a command device. Check the target volume. I 0

7010 8553 The S-VOL is not implemented. You cannot execute the operation for the volume

7010 8554 The S-VOL cannot be used. Contact Hitachi Data Systems Support Center,

7010 8555 The S-VOL is being formatted. Wait until the volume is formatted, and retry the

7010 8556 The S-VOL is a command device. Check the target volume. I 0

Retry the operation with power ON. I 0

I 0

which is not implemented.

I 0

and check if the volume status is normal.

I 0

operation.

I 0

which is not implemented.

I 0

and check if the volume status is normal.

I 0

operation.

7010 8557 The volume is not implemented. You cannot execute the operation for the volume

which is not implemented.

I 0

Hitachi Lightning 9900™ V Series Remote Console Error Codes 59

7010 8558 The volume cannot be used. Contact Hitachi Data Systems Support Center,

and check if the volume status is normal.

I 0

7010 8559 The volume is being formatted. Wait until the volume is formatted, and retry the

7010 8560 The volume is command device. Check the target volume. I 0

7010 8561 The command code is invalid. I 0

7010 8562 The command code sender is invalid. I 0

7010 8563 The volume type is invalid. I 0

7010 8564 The volume type is invalid. I 0

7010 8565 The command code sender is invalid. I 0

7010 8566 The attribute of the reserved volume is invalid. I 0

7010 8567 The number of effective lists is invalid. I 0

7010 8568 The emulation type is invalid. Specify the volume of the supported emulation

7010 8569 The number of multiple jobs exceeded the maximum. Contact Hitachi Data Systems Support Center. I 0

7010 8570 The selected volume does not exist. Refresh the screen, and retry the operation. I 0

7010 8571 The volume is already defined as a reserved volume. I 0

7010 8572 The volume is already defined as a P-VOL. I 0

7010 8573 The volume is defined as a source volume for

hierarchical control.

operation.

type.

Check the corresponding condition. I 0

I 0

7010 8574 The volume is defined as a destination volume for

hierarchical control.

7010 8575 The selected volume is not a reserved volume. I 0

7010 8576 No reserved volume is available for use. I 0

7010 8577 The number of reserved volumes to be defined

exceeds the maximum.

7010 8578 The P-VOL is already paired with a backup volume.

The P-VOL cannot be paired with the target volume.

7010 8579 No volume is defined as a reserved volume. Define the reserve volume, and then retry the

7010 8580 The specified volume is for backup servers only. You cannot use the volume. Specify other

7010 8581 The specified volume is not for backup servers only. I 0

7010 8582 The emulation type of the target volume is being

changed.

7010 8583 The RAID level of the specified volume is not

supported.

7010 8584 No volume is defined as a reserved volume. I 0

7010 8585 The number of reserved volumes exceeds the

maximum.

Check the corresponding condition. I 0

Stop the operation of the Reserve volume setting, or delete the Reserve volume.

I 0

operation.

volume, and retry the operation.

Wait for a while, and retry the operation. I 0

Specify a volume of the supported RAID level. I 0

Stop the operation of the Reserve volume setting, or delete the Reserve volume.

I 0

60 Chapter 1 Error Codes

7010 8586 The number of groups that can be set in the same

subsystem is invalid.

I 0

7010 8587 The number of pairs that can be set in the same group

is invalid.

7010 8588 The specified group number is not set. I 0

7010 8589 The specified group name is invalid. I 0

7010 8590 The group name and the number do not match. I 0

7010 8591 The specified pair is already set in another group. I 0

7010 8592 The command was rejected, because the licensed

capacity was exceeded.

7010 8593 The P-VOL is a source volume for hierarchical control. Check the corresponding condition. I 0

7010 8594 The P-VOL is a destination volume for hierarchical

control.

7010 8595 The specified P-VOL does not exist. Refresh, and then retry the operation. I 0

7010 8596 The specified volume is a reserved volume. I 0

7010 8597 No more pairs can be created for the specified P-VOL. You cannot create pairs for the P-VOL anymore.

7010 8598 The specified volume is not a P-VOL. I 0

7010 8599 The specified volume is already a P-VOL. Specify other P-VOL, and retry the operation. Or

I 0

Check the capacity of the installed license key. If you need to create more pairs, purchase a license key for larger capacity.

Check the corresponding condition. I 0

Delete the existing pairs.

delete the pair of the specified volume, and then retry the operation.

I 0

7010 8600 The RAID level of the specified volume is not

supported.

7010 8601 The target P-VOL cannot be paired with a backup

server volume.

7010 8602 The volume is already a reserved volume. Specify other P-VOL, and retry the operation. Or

7010 8603 The target volume is set as a primary volume for

online data migration.

7010 8604 The target volume is set as a secondary volume for

online data migration.

7010 8605 The Resync command was issued to a device in the

SMPL status.

7010 8606 A new pair was created with an S-VOL forming the

Hitachi TrueCopy cooperation pattern.

7010 8607 A pair status cannot be changed to form the Hitachi

TrueCopy cooperation pattern.

7010 8608 The specified volume is an S-VOL. Refresh the screen, and retry the operation. I 0

7010 8609 The specified volume is not set as a reserved volume. I 0

7010 8610 The S-VOL is a source volume for hierarchical control. Check the corresponding condition. I 0

Check the RAID level, and specify a volume of the supported RAID level, and then retry the operation.

I 0

release the Reserve attribute of the specified volume, and then retry.

I 0

Check the pair status. I 0

Check the volume number for the pair creation, or delete the Remote Copy pair.

Place the TC390 pair which uses the SI390 TVOL as an S-VOL in the PSUE or SMPL status.

I 0

Hitachi Lightning 9900™ V Series Remote Console Error Codes 61

7010 8611 The specified volume is an S-VOL. I 0

7010 8612 The specified volume is not an S-VOL. I 0

7010 8613 The RAID level of the specified S-VOL is not

supported.

7010 8614 The S-VOL is used as a Remote Copy P-VOL. Delete the TrueCopy pair. I 0

7010 8615 The S-VOL is used as a Remote Copy S-VOL. Delete the TrueCopy pair. I 0

7010 8616 The S-VOL is used as a primary volume for online

data migration.

7010 8617 The target S-VOL is used as a secondary volume for

online data migration.

7010 8618 The S-VOL is defined as a P-VOL. Check the volume number. I 0

7010 8619 The target S-VOL is defined as a destination volume

for hierarchical control.

7010 8620 The volume specified as a reserved volume is already

definedas a primary volume for online data migration.

7010 8621 The volume specified as a reserved volume is already

definedas a secondary volume for online data migration.

7010 8622 The volume specified as a reserved volume is already

defined as a Remote Copy M-VOL.

7010 8623 The reserved volume is defined as a Remote Copy R-

VOL.

Specify the volume number of the supported RAID level.

I 0

Check the corresponding condition. I 0

I 0

Delete the TrueCopy pair. I 0

I 0

7010 8624 The selected volume is not paired. Check the specified volume number. I 0

7010 8625 The P-VOL(S-VOL) and S-VOL(T-VOL) have the

same number.

7010 8626 The SMPL command was rejected, because the high-

speed Split was in progress.

7010 8627 The Reverse Resync command was rejected,

because the high-speed Split was in progress.

7010 8628 L1 pair Resync instruction cannot be given because

L2 pair is SP-Pend status.

7010 8629 The status mode specification is invalid. I 0

7010 8630 The status mode type is invalid. I 0

7010 8631 The specified CU number is invalid. I 0

7010 8632 The timing of issuing the command is invalid. Contact Hitachi Data Systems Support Center. I 0

7010 8633 The abnormal status is invalid. Contact Hitachi Data Systems Support Center. I 0

7010 8634 The volume specified as a reserved volume is already

defined as a reserved volume for hierarchical control.

7010 8635 The specified P-VOL is defined as a reserved volume

for hierarchical control .

7010 8636 The specified S-VOL is defined as a reserved volume

for hierarchical control .

Check the specified volume number. I 0

After the high-speed Split is completed, retry the operation.

After changing the status of L2 pair to PSUS, execute the Resync command of L1 pair.

Change the volume number in order to specify the Reserve volume.

I 0

62 Chapter 1 Error Codes

7010 8637 The specified P-VOL is used as a destination volume

for hierarchical control.

Change the volume number in order to specify the Reserve volume.

I 0

7010 8638 The command was rejected, because the target P-

VOL has the settings of FlashAccess.

7010 8639 The command was rejected, because the target S-

VOL has the settings of FlashAccess.

7010 8640 The command was rejected, because a pair sharing

the same P-VOL was in the Reverse Copy status.

7010 8641 The L1 pairs contain a pair in the Reverse Copy

status.

7010 8642 The L2 pairs contain a pair in the Reverse Copy

status.

7010 8643 The request was rejected, because the Reverse Copy

request was made to a pair in the non-Split status.

7010 8644 The request was rejected, because the pair is not in

the Split/Suspend status.

7010 8645 The Reverse Copy request was rejected, because the

P-VOL was shared with a secondary volume of a Remote Copy pair.

7010 8646 The Reverse Copy request was rejected, because the

P-VOL was shared with a Remote Copy pair in the non-suspend status.

You cannot execute the specified operation. Release the FlashAccess setting for the operation.

You cannot execute the specified operation. Release the Reverse Copy for the operation.

Check the pair status. I 0

You cannot execute the specified operation. Release the Remote Copy pair for the operation.

Delete the Remote Copy pair. I 0

I 0

7010 8647 The Reverse Copy request was rejected, because the

S-VOL was shared by a Remote Copy pair.

7010 8648 The boot device and the P-VOL do not match in the

Paircreate command.

7010 8649 Because the boot device is the S-VOL in the Pairsplit-

S command, the flag does not match.

7010 8650 The boot device and the P-VOL do not match in the

Paircreate, Resync, or Pairsplit-S command.

7010 8651 The SSID is invalid. I 0

7010 8652 The boot device is not a P-VOL nor S-VOL. Check the target volume number. I 0

7010 8653 Because the boot device is the P-VOL in the Pairsplit-

S command, the flag does not match.

7010 8654 Boot device and S-VOL do not match in Paircreate,

Resync, or Pairsplit-S instructions.

7010 8655 An invalid secondary SSID is specified for the

Paircreate or Resync command.

7010 8656 An invalid secondary SSID is specified for the

DeletePair or Split command.

7010 8657 The Swap&Freeze option cannot be specified,

because the mode is invalid.

Delete the Remote Copy pair. I 0

Check the specified volume number. I 0

Check the target volume number. I 0

I 0

Check the setting you specified in Option tab. I 0

7010 8658 Some settings could not be applied normally. Refer to

the error code.

Check the error code in Preset volume list. E 0

Hitachi Lightning 9900™ V Series Remote Console Error Codes 63

7010 8659 There is no Fibre-Channel port. E 5

7010 8920 Because a L1 pair is not PSUS, you cannot operate to

L2.

7010 9002 Normal end. The operation was ended normally. Execute the

7010 9005 An error occurred. Check the error code. An error occurred during the indicated operation.

7010 9101 Do you want to cancel? To cancel, press the OK button. I 0

7010 9102 Do you want to apply? To execute the operation in Preset, press the OK

7010 9108 The option has been changed. If you continue

processing before applying the change, the option will be reset to the current setting. Do you want to continue processing?

7010 9109 Do you want to execute the Set Over operation? W 2

7010 9110 Do you want to execute the Initialize operation? To execute the Initialize transaction, press the

7105 5099 An error occurred. If this problem persists, please call

the Support Center.

7110 5115 The T-VOL size differs from the specified source

volume size.

Wait until L1 pair becomes PSUS status, and execute the operation to L2 pair.

next operation.

Refer to the error code for each operation in Preset Volume List.

button.

W 0

OK button. (Inserted only in M.M)

You are trying to set SubSystem ID without Virtual LVI/LUN operation. The error does not occur normally because it is guarded in the screen. Contact the program maker.

Check the capacity of S-VOL and T-VOL. Specify a volume with the same capacity, and retry the operation.

I 0

W 2

E 2

W 0

7110 5116 You cannot create another pair, because the number

of pairs exceeds the maximum.

7110 5119 The S-VOL is not selected Select the S-VOL, and retry the operation. W 0

7110 5120 The T-VOL is not selected. Select the T-VOL, and retry the operation. W 0

7110 5121 The data has been changed. If you select another tab

(page), the settings will be discarded. Are you sure you want to change the pages?

7110 5122 No data has been changed. Go on to the next operation. W 0

7110 5123 The password is invalid. Check the password. W 0

7110 5124 You cannot select more than one operation at a time. Multiple volumes cannot be processed in the

7110 5125 No target volume is selected. Select the target volume. W 0

7110 6502 Currently processing. Wait a few minutes and then

retry the operation.

7110 6503 The volume status is being changed to simplex. Wait for a while, and retry the operation. I 0

7110 6504 The number of pairs exceeds the maximum. You cannot create a pair for the specified S-VOL.

7110 7310 Unregistered error code. Contact Hitachi Data Systems Support Center. W 0

You cannot create the specified pair. Delete the created pair, and then retry the operation.

Apply the data in the Preset Volume List. To stop the transaction, press the OK button and continue the operation.

operation. Process one volume at a time.

Wait for a while, and retry the operation. I 0

Delete the created pair, and retry the operation.

W 0

I 0

64 Chapter 1 Error Codes

7110 7311 The settings could not be applied. Wait for a while, and retry the operation. If the

W 0 same error occurs despite retrying, contact Hitachi Data Systems Support Center.

7110 7312 The password could not be acquired. Contact Hitachi Data Systems Support Center. W 0

7110 7313 The details on the error could not be acquired. Contact Hitachi Data Systems Support Center. W 0

7110 8001 A time-out error occurred. Retry the operation. If you get the same

E 4 message again, reboot the PC. If necessary, please call the Hitachi Data Systems Support Center.

7110 8500 The program product is not installed. Check if the necessary key for the program

I 0 product is installed.

7110 8501 The command was rejected, because a status

Wait for a while, and retry the operation. I 0

transition was in progress.

7110 8502 You cannot reserve the volume, because a remote

Delete the Remote Copy pair. I 0

copy pair exists in the same subsystem frame.

7110 8503 You cannot create the new pair, because a remote

Delete the Remote Copy pair. I 0

copy pair exists in the same subsystem frame.

7110 8504 The command was rejected. You cannot execute the operation with the

I 0 current pair status. Check the pair status.

7110 8505 The requested command is invalid. Contact Hitachi Data Systems Support Center. I 0

7110 8506 The command was rejected. The specified T-VOL is

being used from the host or by a Hitachi TrueCopy-

®

S/390

volume.

7110 8507 The Pairsplit command was issued to the pairs in the

split status.

7110 8508 The AddPair command was issued to the pairs in the

Split status.

I 0

You cannot execute the Pairsplit operation

I 0 because the pair is already in the Split status.

You cannot execute the AddPair operation to the

I 0 pairs in the Split status.

7110 8509 The Split command with the QUIESCE specification

I 0

was issued to a secondary boot device.

7110 8510 The M-VOL Suspend command was issued to a

I 0

secondary boot device.

7110 8511 You cannot reserve the volume, because a path group

is set.

7110 8512 You cannot perform the Resync or Suspend

operation, because a path group is set.

7110 8513 The command was rejected. The specified source

volume is being used from the host or by Remote Copy.

Detach the S-VOL from the host, or delete the TrueCopy path.

Change the specified S-VOL to other volume, or stop using the S-VOL in the host or TrueCopy, and then retry the operation.

I 0

7110 8514 No reserved volume can be allocated. Delete the Reserve volume. I 0

7110 8515 The number of cylinders in the reserved volume

I 0

exceeds the maximum.

7110 8516 The number of S-VOL cylinders exceeds the

I 0

maximum.

7110 8517 The number of T-VOL cylinders exceeds the

I 0

maximum.

Hitachi Lightning 9900™ V Series Remote Console Error Codes 65

7110 8518 You cannot create a pair, because the track format is

different for each. Make sure that the specified emulation type is the same for both.

Check the emulation type. I 0

7110 8519 You cannot set a pair because the number of

cylinders is different for each. Make sure that the capacity is the same for both.

7110 8520 You cannot set a pair, because the volume type is

different for each.

7110 8521 The number of multiple copy jobs exceeded the

maximum.

7110 8522 The emulation type of the S-VOL is not supported. Specify the emulation type supported in

7110 8523 The emulation type of T-VOL is not supported. Specify the emulation type supported in

7110 8524 The emulation type is not supported. Specify the emulation type supported in

7110 8525 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

7110 8526 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

7110 8527 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

7110 8528 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

7110 8529 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

7110 8530 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

Check the volume capacity. I 0

Specify the volume with the same emulation type, and retry the operation.

I 0

ShadowImage.

I 0

7110 8531 Internal logical error. Contact Hitachi Data Systems Support Center. I 0

7110 8532 The S-VOL and T-VOL are being used from the host

or by Remote Copy.

7110 8533 The emulation type of the specified reserved volume

is not supported.

7110 8534 An internal logical contradiction occurred. Contact Hitachi Data Systems Support Center. I 0

7110 8535 A processor failure was detected. Contact Hitachi Data Systems Support Center. I 0

7110 8536 A cache failure was detected. Contact Hitachi Data Systems Support Center. I 0

7110 8537 The cache capacities do not match. Contact Hitachi Data Systems Support Center. I 0

7110 8538 An SM failure was detected. Contact Hitachi Data Systems Support Center. I 0

7110 8539 There is insufficient shared memory to create 4096

pairs.

7110 8540 There is sufficient shared memory to create 4096

pairs, but initial subsystem setup is required before creating pairs.

7110 8541 There is sufficient shared memory to create 4096

pairs, and the initial subsystem setup is complete.

7110 8542 Failed to complete the initial shared memory setup. Contact Hitachi Data Systems Support Center. I 0

7110 8543 The shared memory size is different. Contact Hitachi Data Systems Support Center. I 0

Check the target volume, or stop using it in Remote copy.

Specify the emulation type of the supported volume.

There is insufficient shared memory in DKC. Contact Hitachi Data Systems Support Center.

Contact Hitachi Data Systems Support Center. I 0

I 0

7110 8544 16 Mbytes of shared memory are available. I 0

66 Chapter 1 Error Codes

7110 8545 A power supply failure is detected. Contact Hitachi Data Systems Support Center. I 0

7110 8546 The command was rejected. The PS OFF is in

progress.

7110 8547 A data transfer failure is detected (CHA). Contact Hitachi Data Systems Support Center. I 0

7110 8548 A data transfer failure is detected (DKA). Contact Hitachi Data Systems Support Center. I 0

7110 8549 The S-VOL is not implemented. You cannot execute the operation for the volume

7110 8550 The S-VOL cannot be used. Contact Hitachi Data Systems Support Center,

7110 8551 The S-VOL is being formatted. Wait until the volume is formatted, and retry the

7110 8553 The T-VOL volume is not implemented. You cannot execute the operation for the volume

7110 8554 The T-VOL cannot be used. Contact Hitachi Data Systems Support Center,

7110 8555 The T-VOL is being formatted. Wait until the volume is formatted, and retry the

7110 8556 The T-VOL is command device. I 0

7110 8557 The volume is not implemented. You cannot execute the operation for the volume

7110 8558 The volume cannot be used. Contact Hitachi Data Systems Support Center,

Retry the operation with power ON. I 0

I 0 which is not implemented.

I 0 and check if the volume status is normal.

I 0 operation.

I 0 which is not implemented.

I 0 and check if the volume status is normal.

I 0 operation.

I 0 which is not implemented.

I 0 and check if the volume status is normal.

7110 8559 The volume is being formatted. Wait until the volume is formatted, and retry the

operation.

7110 8561 The command code is invalid. I 0

7110 8562 The command code sender is invalid. I 0

7110 8563 The volume type is invalid. I 0

7110 8564 The volume type is invalid. I 0

7110 8565 The command code sender is invalid. I 0

7110 8566 The attribute of the reserved volume is invalid. I 0

7110 8567 The number of effective lists is invalid. I 0

7110 8568 The emulation type is invalid. Specify the volume of the supported emulation

7110 8569 The number of multiple jobs exceeded the maximum. Contact Hitachi Data Systems Support Center. I 0

7110 8570 The selected volume does not exist. Refresh the screen, and retry the operation. I 0

7110 8571 The volume is already defined as a reserved volume. I 0

7110 8572 The volume is already defined as S-VOL. I 0

7110 8573 The volume is defined as a source volume for

hierarchical control.

7110 8574 The volume is defined as a destination volume for

hierarchical control.

type.

Check the corresponding condition. I 0

I 0

Hitachi Lightning 9900™ V Series Remote Console Error Codes 67

7110 8575 The selected volume is not a reserved volume. I 0

7110 8576 No reserved volume is available for use. I 0

7110 8577 The number of reserved volumes to be defined

exceeds the maximum.

7110 8578 The S-VOL is already paired with a backup volume.

The S-VOL cannot be paired with the target volume.

7110 8579 No volume is defined as a reserved volume. Define the reserve volume, and then retry the

7110 8580 The specified volume is for backup servers only. You cannot use the volume. Specify other

7110 8581 The specified volume is not for backup servers only. I 0

7110 8582 The emulation type of the target volume is being

changed.

7110 8583 The RAID level of the specified volume is not

supported.

7110 8584 No volume is defined as a reserved volume. I 0

7110 8585 The number of reserved volumes exceeds the

maximum.

7110 8586 The number of groups that can be set in the same

subsystem is invalid.

7110 8587 The number of pairs that can be set in the same group

is invalid.

Stop the operation of the Reserve volume setting, or delete the Reserve volume.

I 0

operation.

volume, and retry the operation.

Wait for a while, and retry the operation. I 0

Specify the volume of the supported RAID level. I 0

Stop the operation of the Reserve volume setting, or delete the Reserve volume.

I 0

7110 8588 The specified group number is not set. I 0

7110 8589 The specified group name is invalid. I 0

7110 8590 The group name and the number do not match. I 0

7110 8591 The specified pair is already set in another group. I 0

7110 8592 The command was rejected, because the licensed

capacity was exceeded.

7110 8593 The S-VOL is a source volume for hierarchical control. Check the corresponding condition. I 0

7110 8594 The S-VOL is a destination volume for hierarchical

control.

7110 8595 The specified S-VOL does not exist. Refresh, and then retry the operation. I 0

7110 8596 The specified volume is a reserved volume. I 0

7110 8597 No more pairs can be created for the specified S-VOL. You cannot create pair for the S-VOL anymore.

7110 8598 The specified volume is not an S-VOL. I 0

7110 8599 The specified volume is already an S-VOL. Specify other P-VOL, and retry the operation. Or

7110 8600 The RAID level of the specified volume is not

supported.

Check the capacity of the installed license key. If you need to create more pairs, purchase a license key for larger capacity.

Check the corresponding condition. I 0

Delete the existing pairs.

delete the pair of the specified volume, and then retry the operation.

Check the RAID level, and specify a volume of the supported RAID level, and then retry the operation.

I 0

68 Chapter 1 Error Codes

7110 8601 The source volume cannot be paired with a backup

server volume.

I 0

7110 8602 The volume is already a reserved volume. Specify other volume, and retry the operation. Or

I 0 release the Reserve attribute of the specified volume, and then retry the operation.

7110 8603 The target volume is set as a primary volume for

I 0

online data migration.

7110 8604 The target volume is set as a secondary volume for

I 0

online data migration.

7110 8605 The Resync command was issued to a device in the

Check the pair status. I 0

simplex status.

7110 8606 A new pair was created with an S-VOL forming the

Hitachi TrueCopy-S/390

®

cooperation pattern.

Place the SI390 pair in the SMPL status, or place the TC390 pair which uses the SI390 T-VOL as

I 0

an S-VOL in the Simplex status.

7110 8607 A pair status cannot be changed to from the Hitachi

TrueCopy-S/390

®

cooperation pattern.

Place the TC390 pair which uses the SI390 TVOL as an S-VOL in the Suspended or Simplex

I 0

status.

7110 8608 The specified volume is a T-VOL. Refresh the screen, and retry the operation. I 0

7110 8609 The specified volume is not set as a reserved volume. I 0

7110 8610 The T-VOL is a source volume for hierarchical control. Check the corresponding condition. I 0

7110 8611 The specified volume is a target volume. I 0

7110 8612 The specified volume is not a T-VOL. I 0

7110 8613 The RAID level of the specified target volume is not

I 0

supported.

7110 8614 The target volume is used as a Remote Copy M-VOL. Delete the TrueCopy pair. I 0

7110 8615 The target volume is used as a Remote Copy R-VOL. Delete the TrueCopy pair. I 0

7110 8616 The target volume is used as a primary volume for

I 0

online data migration.

7110 8617 The target T-VOL is used as a secondary volume for

I 0

online data migration.

7110 8618 The requested T-VOL volume is already defined as an

Check the volume number. I 0

S-VOL.

7110 8619 The target T-VOL is defined as a destination volume

Check the corresponding condition. I 0

for hierarchical control.

7110 8620 The volume specified as a reserved volume is already

I 0

definedas a primary volume for online data migration.

7110 8621 The volume specified as a reserved volume is already

I 0

definedas a secondary volume for online data migration.

7110 8622 The volume specified as a reserved volume is already

Delete the TrueCopy pair. I 0

defined as a Remote Copy M-VOL.

7110 8623 The reserved volume is defined as a Remote Copy R-

Delete the TrueCopy pair. I 0

VOL.

7110 8624 The selected volume is not paired. Check the specified volume number. I 0

Hitachi Lightning 9900™ V Series Remote Console Error Codes 69

7110 8625 The P-VOL(S-VOL) and S-VOL(T-VOL) have the

same number.

Check the specified volume number. I 0

7110 8626 The Simplex command was rejected, because the

high-speed Split was in progress.

7110 8627 The Reverse Resync command was rejected,

because the high-speed Split was in progress.

7110 8629 The status mode specification is invalid. I 0

7110 8630 The status mode type is invalid. I 0

7110 8631 The specified CU number is invalid. I 0

7110 8632 The timing of issuing the command is invalid. Contact Hitachi Data Systems Support Center. I 0

7110 8633 The abnormal status is invalid. Contact Hitachi Data Systems Support Center. I 0

7110 8634 The volume specified as a reserved volume is already

defined as a reserved volume for hierarchical control.

7110 8635 The specified S-VOL is defined as a reserved volume

for hierarchical control.

7110 8636 The specified T-VOL is defined as a reserved volume

for hierarchical control .

7110 8637 The specified S-VOL is used as a destination volume

for hierarchical control.

7110 8638 The command was rejected, because the target S-

VOL has FlashAccess settings.

After the high-speed Split is completed, retry the operation.

Change the volume number in order to specify the Reserve volume.

You cannot execute the specified operation. Release the FlashAccess setting for the operation.

I 0

7110 8639 The command was rejected, because the target T-

VOL has FlashAccess settings.

7110 8640 The command was rejected, because a pair sharing

the same S-VOL was in the Reverse Copy status.

7110 8641 The pairs contain a pair in the Reverse Copy status. You cannot execute the specified operation.

7110 8643 The request was rejected, because the Reverse Copy

request was made to a pair in the non-Split status.

7110 8644 The request was rejected, because the pair is not in

the Split/Suspend status.

7110 8645 The Reverse Copy request was rejected, because the

S-VOL was shared with a secondary volume of a Remote Copy pair.

7110 8646 The Reverse Copy request was rejected, because the

S-VOL was shared with a Remote Copy pair in the non-suspend status.

7110 8647 The Reverse Copy request was rejected, because the

T-VOL was shared by a Remote Copy pair.

7110 8648 The boot device and the S-VOL do not match in the

AddPair command.

7110 8649 Because the boot device is the T-VOL in the

DeletePair command, the flag does not match.

You cannot execute the specified operation. Release the FlashAccess setting for the operation.

You cannot execute the specified operation. Release the Reverse Copy for the operation.

Release the Reverse Copy for the operation.

You cannot execute the specified operation. Release the Reverse Copy for the operation.

Check the pair status. I 0

You cannot execute the specified operation. Release the Remote Copy pair for the operation.

Delete the Remote Copy pair. I 0

Check the specified volume number. I 0

I 0

70 Chapter 1 Error Codes

7110 8650 The boot device and the S-VOL do not match in the

AddPair, Resync, or DeletePair command.

7110 8651 The SSID is invalid. I 0

7110 8652 The boot device is not an S-VOL nor T-VOL. Check the target volume number. I 0

Check the specified volume number. I 0

7110 8653 Because the boot device is the S-VOL in the

DeletePair command, the flag does not match.

7110 8654 The boot device and the T-VOL do not match in the

AddPair, Resync, or DeletePair command.

7110 8655 An invalid secondary SSID is specified for the AddPair

or Resync command.

7110 8656 An invalid secondary SSID is specified for the

DeletePair or Split command.

7110 8657 The Swap&Freeze option cannot be specified,

because the mode is invalid.

7110 8658 Some settings could not be applied normally. Refer to

the error code.

7110 8659 There is no volume. I 0

7110 9002 Normal end. The operation was ended normally. Execute the

7110 9005 An error occurred. Check the error code. An error occurred during the indicated operation.

7110 9101 Do you want to cancel? To cancel, press the OK button. I 0

7110 9102 Do you want to apply? To execute the operation in Preset, press the OK

Check the target volume number. I 0

I 0

Check the setting you specified in Option tab. I 0

Check the error code in Preset volume list. E 0

I 0 next operation.

I 0 Refer to the error code for each operation in Preset Volume List.

I 0 button.

7110 9108 The option has been changed. If you continue

processing before applying the change, the option will be reset to the current setting. Do you want to continue processing?

7110 9109 Do you want to execute the Set Over operation? W 2

7110 9110 Do you want to execute the Initialize operation? W 2

8005 3003 An error occurred. If this problem persists, please call

the Support Center.

8005 5099 An error occurred. If this problem persists, please call

the Support Center.

8005 6023 An error occurred. If this problem persists, please call

the Support Center.

8005 6040 An error occurred while connecting to the subsystem.

Please retry a little later.

8005 6050 An error occurred. If this problem persists, please call

the Support Center.

W 0

When host mode is set, the maximum value you can set in the PORT is exceeded. The error does not occur normally because it is guarded in the screen. Contact the program maker.

You have not specified the value when registering WWN. Or zero is set as the WWN value. The error does not occur normally because it is guarded in the screen. Contact the program maker.

E 2

Call the service personnel. E 6

Call the service personnel. E 2

E 2

Hitachi Lightning 9900™ V Series Remote Console Error Codes 71

8005 7111 An error occurred. If this problem persists, please call

the Support Center.

E 2

8005 8001 An error occurred while connecting to the subsystem.

Please retry a little later.

8005 8100 An error occurred while connecting to the subsystem.

Please retry a little later.

9005 5099 An error occurred. If this problem persists, please call

the Support Center.

9005 6001 An error occurred. If this problem persists, please call

the Support Center.

9005 6012 An error occurred. If this problem persists, please call

the Support Center.

9005 6036 An error occurred. If this problem persists, please call

the Support Center.

9005 6502 This key code is invalid. Please wait for a moment and retry. W 5

9005 7111 An error occurred. If this problem persists, please call

the Support Center.

9005 7112 An error occurred. If this problem persists, please call

the Support Center.

9005 7113 An error occurred. If this problem persists, please call

the Support Center.

Retry the same operation several times. If the same error occurs, call the service personnel.

You have specified Virtual LVI/LUN operation to a request of the configuration information setting. The error does not occur normally because it is guarded in the screen. Contact the program maker.

Please call your maintenance support center to report them with the error code.

E 2

Please check the inputted value and retry. E 2

Call the service personnel. E 2

E 6

E 2

9005 7114 An error occurred. If this problem persists, please call

the Support Center.

9005 7115 An error occurred. If this problem persists, please call

the Support Center.

9005 7116 An error occurred. If this problem persists, please call

the Support Center.

9005 7117 An error occurred. If this problem persists, please call

the Support Center.

9005 8100 An error occurred while connecting to the subsystem.

Please retry a little later.

9005 8102 This function is not supported. Please check the DKC microcode version. E 6

9005 8103 The subsystem status is invalid. Please call the

Support Center.

Call the service personnel. E 2

Please call your maintenance support center to report them with the error code.

Please check the DKC microcode version. E 2

E 6

72 Chapter 1 Error Codes

Acronyms and Abbreviations

API application program interface

CCI Command Control Interface CHA channel adapter CT consistency CTG consistency group CU control unit CV custom volume

DASD direct-access storage device DFW DASD fast write DKA disk adapter DKC disk controller

HPAV Hitachi Parallel Access Volume

IP internet protocol

L1, L2 level 1, level 2 LAN local-area network LBA logical block address LCP local control port LDEV logical device LU logical unit LUN logical unit number LUSE LUN Expansion

MCU main control unit MIB message information block MU mirror unit M-VOL main volume

NVS nonvolatile storage

PA Priority Access PDEV physical device P.P. Program Product PS power supply PSUE pair suspended-error (status) PSUS pair suspended-split (status) P-VOL primary volume

RAID redundant array of independent disks RCP remote control port RCU remote control unit R-VOL remote volume

SI390 ShadowImage – S/390 SIM service information message

®

Hitachi Lightning 9900™ V Series Remote Console Error Codes 73

SM shared memory SMPL simplex SNMP simple network management protocol SSID subsystem ID S-VOL secondary volume (TrueCopy), source volume (ShadowImage – S/390 SVP service processor

®

)

TC390 TrueCopy – S/390

®

T-VOL target volume

VDEV virtual device

WWN worldwide name

74 Acronyms and Abbreviations

Hitachi Freedom Storage Lightning 9900 V Error Code List

© 2002 Hitachi Data Systems Corporation, ALL RIGHTS RESERVED

Trademarks

Notice of Export Controls

Document Revision Level

Source Documents for this Revision

Changes in this Revision

Referenced Documents

Preface

Microcode Level

COMMENTS

Contents

Chapter 1 Remote Console Messages and Error Codes

1.1 Remote Console Messages

Figure 1.1 Sample Error Message

1.2 Error Codes

Table 1.1 Error Codes

Acronyms and Abbreviations