Hitachi DVPF2EUK User Manual

DVD/VCR Combo (DVD PLAYER with VIDEO CASSETTE RECORDER)
OPEN/ CLOSE
DVD VCR
TIMER SET
STANDBY
CST.IN
OUTPUT
CHANNEL
VIDEO IN
L
(mono)
R
AUDIO IN
INSTRUCTION MANUAL
VIDEOPlus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The
PAL
VIDEOPlus+ system is manufactured under license from Gemstar Development Corporation.
MODEL
DVPF2EUK
English
Instruction manual
To obtain the best performance and ensure years of trouble­free use, please read this instruction manual completely.
–1–
EN
2C15
WARNING
CAUTION - VISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. AVOID EXPOSURE TO BEAM.
CLASS 1 LASER PRODUCT KLASSE 1 LASER PRODUKT KLASS 1 LASER APPARAT CLASSE 1 PRODUIT LASER
FUSE
BROWN
(Live)
CORD GRIP
OUTER SHEATH OF THE WIRE
BLUE
(Neutral)
:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SER­VICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
:
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the pres­ence of important operating and maintenance (servicing) instructions in the literature accom­panying the appliance.
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.
CAUTION:
CAUTION: VISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED.
LOCATION:
* PRINTED ON THE BACK * INSIDE, TOP OF THE MECHANISM
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
AVOID EXPOSURE TO BEAM.
CONNECTION TO POWER
Before Switching on make sure that the voltage of your electricity supply is the same as that indicated on the rating plate.
Mains Cord
This appliance may be fitted with a non-rewireable plug. If it is necessary to change the fuse in a non-rewireable plug the fuse cover must be refitted. If the fuse cover is lost or damaged, the plug must not be used until a replacement available from the appliance manufacturer is obtained. It is important that the colour of the replacement fuse cover corresponds with the rating marking on the base of the plug. If the plug has to be changed because it is not suitable for your socket, or becomes damaged, it should be cut off and an appropriate plug fitted following the wiring instructions below. The plug removed must be disposed of safely as insertion into a 13A socket is likely to cause an electrical hazard. For your own safety read the following instructions carefully before attempting to connect this unit to mains. The wires in this mains lead are coloured in accordance with the following code: BLUE=NEUTRAL, BROWN=LIVE
(For the area of Great Britain)
Important
As the colours of the wires in the mains lead of this appli­ance may not correspond with the coloured markings iden­tifying the terminals in your plug, proceed as follows:­The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. No connection is to be made to the earth terminal of the plug. If a 13 Amp (BS 1363) Plug is used, a 3 Amp Fuse must be fitted, of if any other type of Plug is used a 3 or 5 Amp Fuse must be fitted, either in the Plug or Adaptor, or on the Distribution Board. Mains Supply: 220 - 240 V
50 Hz - AC only
˜
Do not make any connection to the larger pin marked with the letter “E” or by the symbol or coloured green or green and yellow.
–2–
EN
2C15
PRECAUTIONS
POWER SUPPLY
The main power supply is engaged when the main plug is plugged in a 220-240V˜50Hz AC outlet. To operate the unit, press the (Standby/Power ON) Button to turn on the unit.
WARNING
To avoid fire or electric shock, do not expose this unit to rain or moisture.
DEW WARNING
Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under con-
WARNING: LIVE PARTS INSIDE. DO NOT REMOVE ANY SCREWS.
ditions of high humidity. Do not use the DVD/VCR Player at least for 2 hours until its inside is dry.
CAUTION
1) Do not attempt to open the cabinet. There are no parts you can service inside. Refer all ser­vicing to qualified service personnel.
2) Slot and openings in the cabinet and at the side or bottom are provided for ventilation. To ensure reliable operation and to protect the unit from overheating these opening must not be blocked or covered. Avoid enclosed spaces such as book cases unless proper ventilation is provided.
3) Keep the unit away from the radiator heat sources.
4) Avoid using near strong magnetic fields.
5) Do not push objects of any kind into this through the cabinet slot as they could touch current carrying parts or short circuit parts resulting in a fire or electric shock.
6) Never spill liquid of any kind on this unit. If liquid is spilled into the unit, consult quali­fied service engineer.
7) Use this unit in a horizontal (flat) position only.
8) This equipment is in Stand-by mode when it turns off whilst the power cord is connected.
English
DECLARATION OF
CONFORMITY
This product complies with the requirement of the directives EMC-Directive: 89 / 336 / EEC Low Voltage Directive: 73 / 23 / EEC CE Marking: 93 / 68 / EEC
declare that the DVD/VCR player with video cassette recorder
DV-PF2E(UK)
are in compliance with following norms:
EN 55013:1990
+A12:1994+A13:1996+A14:1999
EN 55020:1994
+A11:1996+A12:1999+A13:1999+A14:1999
EN
61000-3-2:1995+A14:2000, EN61000-3-3:1995 EN 60065:1998 EN 60825-1:1994
–3–
EN
2C15
A NOTE ABOUT RECYCLING
+10
C
LO
SE
3
Q
U
IC
K
-F
IN
D
2
S
E
A
R
C
H
M
O
D
E
/
O
P
E
N
/
9
ZOOM
D
IS
PLA
Y
8
AUDIO
0
SETUP
SKIP
CH
56
1
A-B REPEAT
REPEAT
7
SUBTITLE
MODE
ANGLE
DVD
S
U
R
R
O
U
N
D
VCR
SLOW
SPEED
REC
RETURN
MENU
4
DV-PMPF2E(UK)
ENTER
TOP MENU/VIDEO Plus+
D
A
ILY
/W
E
E
K
LY
IN
D
EX
SE
AR
C
H
T
IM
E
SEA
R
C
H
M
E
N
U
S
E
L
E
C
T
E
N
T
E
R
C
LE
A
R
/C
.R
E
S
T
This products packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
The serial number of this product may be found on the back of the DVD/VCR. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
ABOUT COPYRIGHT
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
SUPPLIED ACCESSORIES
Remote control
(DV-RMPF2E (UK))(TS16907)
Two AA batteries
RF Coaxial Cable
75 ohm (TE15231)
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some headings and notes in this manual, with the following meanings!
VCR
: Description refers to playback of video cassette tapes.
DVD
: Description refers to playback of DVD video discs.
CD
: Description refers to playback of audio CDs.
MP3
: Description refers to playback of MP3 discs.
–4–
EN
2C15
TABLE OF CONTENTS
LASER SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
CONNECTION TO POWER (For the area of Great
Britain) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
DEW WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CAUTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
DECLARATION OF CONFORMITY . . . . . . . . . . . . . . . . . . 3
ABOUT COPYRIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . 4
SYMBOLS USED IN THIS MANUAL . . . . . . . . . . . . . . . . . 4
FEATURES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ABOUT THE DISCS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
PLAYABLE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
DISC TYPES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
OPERATING CONTROLS AND FUNCTIONS . . . . . . . . . . 9
DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
DISPLAYS DURING OPERATION. . . . . . . . . . . . . . . . . . . 14
LOADING THE BATTERIES . . . . . . . . . . . . . . . . . . . . . . . 14
VCR/DVD SWITCHING . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
HOOKUPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
DESCRIPTION-REAR PANEL . . . . . . . . . . . . . . . . . . . . . . 16
DVD/VCR TO TV CONNECTION . . . . . . . . . . . . . . . . . . . 17
OTHER CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 17
CONNECTION TO AN AUDIO SYSTEM . . . . . . . . . . . . . 18
CONNECTION TO A TV (FOR DVD/VCR) . . . . . . . . . . . . 19
HI-FI STEREO SOUND SYSTEM . . . . . . . . . . . . . . . . . . . 20
SELECTING THE SOUND MODE . . . . . . . . . . . . . . . . . . . 20
PRESET FOR USE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
VIDEO CHANNEL SETTING. . . . . . . . . . . . . . . . . . . . . . . 20
SETTING THE CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
TUNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
AUTOMATIC TUNING. . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
MANUAL TUNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
TO SKIP A PRESET CHANNEL. . . . . . . . . . . . . . . . . . . . . 23
CHANNEL ORDER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
BASIC OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SPEED SEARCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SLOW MOTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ADVANCED OPERATIONS . . . . . . . . . . . . . . . . . . . . . . . . 26
OTR (ONE TOUCH RECORDING) . . . . . . . . . . . . . . . . . . 26
AUTO REPEAT PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . 26
PICTURE SELECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
AUTOMATIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . 27
REAL TIME TAPE COUNTER . . . . . . . . . . . . . . . . . . . . . . 27
TIMER RECORDING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
HINTS FOR TIMER RECORDING. . . . . . . . . . . . . . . . . . . 28
TIMER RECORDING USING THE VIDEO Plus®+ SYSTEM
PDC(Programme Delivery Control) . . . . . . . . . . . . . . . . . . . 29
AUTO RETURN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
QUICK-FIND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
TIME SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
INDEX SEARCH. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
COPYING A VIDEO TAPE . . . . . . . . . . . . . . . . . . . . . . . . . 31
A STATUS DISPLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
VIDEO CASSETTE TAPE. . . . . . . . . . . . . . . . . . . . . . . . . . 32
TV COLOUR SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . 29
PLAYING A DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
PLAYING A DVD VIDEO OR AN AUDIO CD . . . . . . . . . 33
USING THE DVD MENUS. . . . . . . . . . . . . . . . . . . . . . . . . 33
USING THE TITLE MENU. . . . . . . . . . . . . . . . . . . . . . . . . 34
PAUSING PLAYBACK OR DISPLAYING
A STILL PICTURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
RESUMING PLAYBACK FROM THE POINT WHERE
PLAYBACK STOPPED. . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
STEPPING THROUGH FRAMES. . . . . . . . . . . . . . . . . . . . 34
FAST FORWARD/REVERSE . . . . . . . . . . . . . . . . . . . . . . . 35
SLOW MOTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
STARTING FROM A DESIRED TRACK . . . . . . . . . . . . . . 35
STARTING FROM A DESIRED TITLE OR CHAPTER . . . 35
STARTING FROM A DESIRED TIME COUNT . . . . . . . . . 36
MARKER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
RANDOM (Audio CD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
REPEAT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
PROGRAMME (Audio CD). . . . . . . . . . . . . . . . . . . . . . . . . 37
ZOOM PLAYBACK (enlargement on-screen) . . . . . . . . . . . 38
PLAYING AN MP3 DISC . . . . . . . . . . . . . . . . . . . . . . . . . . 38
CHANGING THE ON-SCREEN DISPLAY
DURING MP3 DISC PLAY . . . . . . . . . . . . . . . . . . . . . . . . . 39
PLAYING AN MP3 DISC FROM A DESIRED TRACK . . . 39
PLAYING AN MP3 DISC AT RANDOM . . . . . . . . . . . . . . 39
PLAYING AN MP3 DISC IN A PROGRAMMED WAY . . . 39
SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
CHANGING THE AUDIO LANGUAGE
OR SOUND MODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
CHANGING THE SUBTITLE LANGUAGE. . . . . . . . . . . . 41
CHANGING THE CAMERA ANGLE
(Multi-Angle Pictures) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
CHANGING THE ON-SCREEN DISPLAY. . . . . . . . . . . . . 42
BLACK LEVEL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . 42
TRUSURROUND SETTINGS . . . . . . . . . . . . . . . . . . . . . . . 42
CHANGING THE SETUP ITEMS . . . . . . . . . . . . . . . . . . . 43
LANGUAGE SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . 43
DISPLAY SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
AUDIO SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
PARENTAL LOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
LANGUAGE CODE LIST. . . . . . . . . . . . . . . . . . . . . . . . . . 47
TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . 48
HANDLING PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . 50
DISC HANDLING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
BATTERY SAFETY GUIDELINES . . . . . . . . . . . . . . . . . . 54
SUBSIDIARY INFORMATION . . . . . . . . . . . . . . . . . . . . . 55
English
–5–
EN
2C15
FEATURES
This unit employs TruSurround system
of SRS Labs, Inc. as virtual
technology.
TruSurround and symbol are trademarks of SRS Labs, Inc. TruSurround technology is incorporated under license from SRS Labs, Inc.
DVD
¡Dolby Digital sound
This player can handle Dolby Digital surround sound having 5.1 channels when connected to a Dolby Digital decoder.
¡Still/fast/slow/step playback
Various playback modes are available including still pic­tures, fast forward/reverse, slow motion and step frames.
¡Random playback for audio CD and MP3
This player can shuffle the order of tracks to play them in random order.
¡Programme playback for audio CD and MP3
You can programme the order of tracks to play them in any desired order.
¡DVD menus in a desired language
You can display DVD menus in a desired language, if available on a DVD.
¡Screen saver/Auto power-off functions
The screen saver programme starts when there is no input from the player for five minutes in the stop mode. When the screen saver programme is activated for 30 minutes, the screen saver is automatically turned off.
¡Subtitles in a desired language
You can select a desired language for the display subtitles, if that language is available on a disc.
¡Selecting a camera angle
You can select the desired camera angle, if a disc contains sequences recorded from different angles.
¡Choices for audio language and sound mode
You can select the desired audio language and sound mode, if different languages and modes are available on a disc.
¡Parental lock
You can set the control level to limit playback of discs which may not be suitable for children.
¡Automatic detection of discs
This player automatically detects if a loaded disc is DVD, audio CD or MP3 on disc.
¡Playing an MP3 disc
You can enjoy MP3 files which are recorded on CD-R/RW.
¡Direct Search
You can search the desired title, chapter, and track with Number Button during playback or in stop mode.
Mode
¡On-screen display
Information about the current operation can be displayed on a TV screen, allowing you to confirm the currently active functions (such as programme playback), on the TV screen using the remote control.
¡DTS (Digital Theater System)
Sound system different from Dolby Digital sound system.
¡Search
Chapter search: Search for the chapter designated by user
Title search: Search for the title designated by user is
Track search: Search for the track designated by user is
Time search: Search for the time designated by user is
¡Repeat
Chapter: Repeated playback of the chapter of the
Title: Repeated playback of the title of the disc
Track: Repeated playback of the track of the disc
Disc
(audio CD)
A-B: The part between A and B designated by
Album: Repeated playback of the folder of the
¡Zoom
2-time and 4-time magnified screen can be displayed.
¡Marker
The part designated by user can be called back.
¡Resume Play
User can resume to playback from the part at which the play was stopped even if the power turn off.
¡SRS TruSurround
You can enjoy stereophonic virtual space on your existing stereo system.
¡Component Video Out Jacks
Jacks located on the back of the DVD/VCR which are used to send high-quality video to a TV via Component Video In Jacks.
¡Dimmer
Brightness of the display can be varied.
¡Bit rate indication
¡DRC (Dynamic range control)
You can control the range of sound volume.
is possible.
possible.
possible.
possible.
disc being played is possible.
being played is possible.
being played is possible.
: Repeated playback is possible.
(MP3): Repeated playback is possible.
user is possible.
MP3 disc being played is possible.
–6–
EN
2C15
VCR
Mode
Hardware specifications
¡AUDIO OUTPUT L/R jacks
¡Auto Head Cleaner
¡4 Head HiFi Stereo
¡On Screen Display
¡PLL Synthesiser Tuner with 99 channels
presettable
Automatic functions
¡Auto power on system
Automatically turns the DVD/VCR on when you insert a cassette.
¡Automatic Operations
¡Digital Auto Tracking (DTR)
Playback
¡Auto Repeat
¡Auto Return
¡NTSC Playback
¡Picture Select
¡Quick-Find
¡Slow Motion
¡Index Search
¡Time Search
¡2 Step Picture Search Operation
English
Recording
¡One Touch Recording
¡1 Year, 8 events Timer Recording (including Once,
Daily, Everyday, and Weekly Timer Recording)
¡PDC(Programme Delivery Control)
PRECAUTIONS
INSTALLATION LOCATION
For safety and optimum performance of your DVD/VCR:
• Install the DVD/VCR in a horizontal and stable posi­tion. Do not place anything directly on top of the DVD/VCR. Do not place the DVD/VCR directly on top of the TV.
• Shield it from direct sunlight and keep it away from sources of intense heat. Avoid dusty or humid places. Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes on the sides of the DVD/VCR. Avoid locations subject to strong vibration or strong magnetic fields.
AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE
Do not handle the power cord with wet hands.
Do not pull on the power cord when disconnecting it
from AC wall outlet. Grasp it by the plug.
If, by accident, water is spilled on your DVD/VCR, unplug the power cord immediately and take the unit to our Authorized Service Center for servicing.
Do not put your fingers or objects into the DVD/VCR cassette holder.
MOISTURE CONDENSATION WARNING
Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. Do not use the DVD/VCR at least for 2 hours until its inside is dry.
–7–
EN
2C15
ABOUT THE DISCS
DVD
Video
12 cm
Approx. 4 h
(single-sided)
Approx. 80 min
(single-sided)
8cm
Logo
Maximum
Playback Time
ContentsDisc Type
Sound
and
Pictures
Disc Size
74 min
Approx. 8 h
(double-sided)
Approx. 160 min
(double-sided)
12 cm
20 min
8cm
(singles)
Audio
CD
Sound
TM
Example
Title 1 Title 2
Chapter 1 Chapter 2 Chapter 1 Chapter 2Chapter 3 Chapter 4
Example
Track 1 Track 2 Track 3 Track 4 Track 5 Track 6
Example
Album 1 Album 2
Track 1 Track 2 Track 1 Track 2Track 3 Track 4
PLAYABLE DISCS
The following discs can be played back on this DVD/VCR.
¡Some discs include region codes as shown below.
¡The number inside the symbol refers to a region of the
world, and a disc encoded in a specific region format can only be played back on the player with the same region code.
The following discs cannot be played back on this DVD/VCR.
¡
DVD with region codes other than 2 or ALL.
¡
DVD-ROM
¡
DVD-RAM (Never play back, otherwise malfunction may result.)
¡
CD-ROM
¡
VSD
¡
CDV (Only plays back the audio part.)
¡
CD-G (Only plays back the audio part.)
¡
CD-R/CD-RW (Only plays back the discs which audio CD and MP3 is recorded.)
¡
CD-I (Never play back, otherwise malfunction may result.)
¡
SACD
¡
Photo CD (Never play back, otherwise malfunction may result.)
¡
DVD-Audio
¡
Any other discs without compatibility indica­tions
DISC TYPES
[
]
DVD
Data on a DVD is divided into sections called "titles", and then into subsections called "chapters", each of which is given a title or chapter number. Playback conditions are preset on some DVD video discs, and these playback con­ditions take priority over user operations on this player. If a function you selected do not run as desired, refer to the manual accompanying the disc.
[
AUDIO CD
Data on an audio CD is divided into sections called tracks, each of which is given a track number.
[
MP3
Data on a MP3 is divided into sections called "albums", and then into subsections called "tracks", each of which is given an album or track number.
–8–
]
]
EN
2C15
OPERATING CONTROLS AND FUNCTIONS
OPEN/ CLOSE
DVD VCR
TIMER SET
STANDBY
CST.IN
OUTPUT
CHANNEL
VIDEO IN
L
(mono)
R
AUDIO IN
1 2 3 64587
9
26
25
242322
21
20
1918171615
14
13
10
11
12
OPEN/ CLOSE
DVD VCR
TIMER SET
STANDBY
CST.IN
OUTPUT
CHANNEL
VIDEO IN
L
(mono)
R
AUDIO IN
FRONT PANEL
REMOTE CONTROL
SEARCH MODE/
OPEN/
CLOSE
QUICK-FIND
27
28
29
30 31
32
REPEAT
MODE
ZOOM
ANGLE
1
4
7
CLEAR/C.RESET
SUBTITLE
3
2
56
9
8
DAILY/WEEKLY
0
+10
DISPLAY
AUDIO
A-B REPEAT
33
MENU
TOP MENU/VIDEO Plus+
34
35 36
37 38
RETURN
DVD
ENTER
SURROUND
SETUP
VCR
39
40
41 42
SLOW SPEED REC
SKIP CH
INDEX SEARCH TIME SEARCH
MENU SELECT
ENTER
43
VCR operation Buttons : Blue DVD operation Buttons : Green Common operation Buttons : White
1. Disc loading tray
2. DVD OUTPUT Light (Green) [page 15]
This light appears when the DVD output mode is select­ed. You can only watch DVDs when the green DVD
58
57
56
55
54
53 52
51 50 49
48
47 46
45 44
OUTPUT Light is on. To make the green DVD OUT­PUT light come on, press the DVD Button on the remote control or the OUTPUT Button on the front panel.
3. VCR OUTPUT Light (Green) [page 15]
This light appears when the VCR output mode is selected. You can only watch tapes when the green VCR OUTPUT light is on. To make the green VCR OUTPUT light come on, the VCR Button on the remote control or the OUTPUT Button on the front panel.
4. CASSETTE COMPARTMENT
5. REC/OTR Light [page 26]
Lights up during recording.
6. TIMER SET Light [page 27]
This light glows when the DVD/VCR is in standby mode or off for a timer recording or during a One­Touch Recording. It flashes if the TIMER SET Button is pressed for a timer recording, but there is no tape in the DVD/VCR. It flashes when all timer recordings or One Touch Recording are finished.
7. (Standby/Power ON) Button
Press to turn the power on and off.
8. (Standby/Power ON) Light
Lights up when the power is on.
9. VIDEO In Jack
Connect a video cable coming from the video out jack of a camcorder, another VCR, or a video source (laser disc player, etc.) here.
10. AUDIO In Jacks
Connect audio cables coming from the audio out jacks of a camcorder, another VCR, or an audio source here.
11. TIMER SET Button [page 27]
Press to put the DVD/VCR into standby mode for a timer recording.
12. STANDBY Light
Lights up when the DVD/VCR is plugged in.
13. CST. IN Light
Lights up when a cassette is in the DVD/VCR.
14. CHANNEL Buttons [page 17,25]
In VCR mode, press to change TV channels on the DVD/VCR; press to adjust the tracking during nor­mal or slow motion playback; press to remove verti­cal jitter in a Still picture.
15. REC/OTR Button (VCR) [page 25,26]
Press once to start a recording. Press repeatedly to start an One Touch Recording Timer.
English
–9–
EN
2C15
16. g(F.FWD) Button (VCR) [page 21]
Press to rapidly advance the tape, or view the picture rapidly in forward during playback. (Forward Search). When setting programme (For example:set­ting clock or timer programme), press to determine your selection and proceed to the next step you want to input. Press to determine the setting modes from the on screen menu. Press to add or delete channel numbers during channel preset.
17. B(PLAY) Button (VCR) [page 21]
Press to begin playback. Press to enter digits when setting programme (For example: setting clock or timer programme). Press to select the setting modes from the on screen menu.
18. h(REW) Button (VCR) [page 21]
Press to rewind the tape, or to view the picture rapid­ly in reverse during the playback mode (Rewind Search). Press to cancel a setting of timer pro­gramme. Press to correct digits when setting pro­gramme (For example: setting clock or timer pro­gramme). Press to add or delete channel numbers during channel preset.
19. C/A
20. OUTPUT Button [page 15]
21.
22. B(PLAY) Button (DVD) [page 33]
23. j/h
24. C(STOP) Button (DVD) [page 33]
25. OPEN/CLOSE Button [page 33]
26. Display, Remote Sensor Window
27. (Standby/Power ON) Button
28. A-B REPEAT Button [page 37]
29. REPEAT Button [page 36]
30. MODE Button [pages 36]
(STOP/EJECT) Button (VCR) [
EJECT Button
Press to remove the tape from the DVD/VCR.
STOP Button
Press to stop the tape motion. Press to enter digits when setting programme (For example:setting clock or timer programme). Press to select the set­ting modes from the on screen menu.
Press to select DVD mode or VCR mode.
You can switch the output mode of the DVD/VCR
either by pressing the OUTPUT Button on the front panel, or by pressing the DVD or VCR Button on the remote control. However,
only the OUTPUT Button on the front panel does not switch the output mode of the remote control. If you want to use the remote control, you always need to select the correct output mode on the remote control, too.
g/G(SKIP) Button (DVD) [page 36]
Plays back from the beginning of the next chapter or track. Hold down to fast forward playback.
Starts playback of the disc contents.
(SKIP) Button (DVD) [page 36]
Plays back from the beginning of the current chapter or track. Hold down to fast reverse playback.
Stops operation of the disc.
Press to insert discs into or remove them from the tray.
Press to turn the power on and off.
Repeats playback of a selected section.
Repeats playback of the current disc, title, chapter or track.
Activates programme playback or random playback mode when playing CDs or MP3. Sets Black level or SRS TruSurround.
page 28
]
pressing
31. ZOOM Button [page 38]
Enlarges part of a DVD-reproduced image.
32. CLEAR/C.RESET Button
DVD mode [page 36]
Press to reset the setting.
VCR mode [page 23]
Press to reset the counter.
33. ANGLE Button [page 41]
Press to change the camera angle to see the sequence being played back from a different angle.
34. MENU Button
DVD mode [page 33]
Press to display the menu of the Disc.
VCR mode [page 21]
Press to access the VCR menu.
35. ENTER Button [page 33]
Press to accept a setting.
36. Arrow Buttons (L/K/s/B) [page 33]
Use when making settings while watching the display on a TV screen.
37. RETURN Button [page 36]
Returns to the previous operation.
38. SURROUND Button [page 42]
Press to enjoy stereophonic sound system when
you playback Dolby Digital and PCM 48kHz sound.
39. DVD Button [page 15]
Press to select DVD mode for the remote control.
You can switch the output mode of the DVD/VCR
either by pressing the OUTPUT Button on the front panel, or by pressing the DVD or the VCR Button on the remote control. However,
only the OUTPUT Button on the front panel does not switch the output mode of the remote control. If you want to use the remote control, you always need to select the correct output mode on the remote control, too.
40.
SLOW Button (VCR) [page 24]
During tape playback, press to view the video tape in slow motion. Press the playback. This Button does not affect DVD playback.
41. SKIP Buttons (j/G
Press to skip Chapters or Tracks.
INDEX SEARCH Button (j) (VCR) [page 30]
Press to perform Index Search.
TIME SEARCH Button (G) (VCR) [page 30]
Press to perform Time Search.
42. C(MENU SELECT/STOP) Button
DVD mode [page 33]
Stops operation of the disc.
VCR mode [page 25]
Press to stop the tape motion. Press to enter digits when setting programme (For example: setting clock or timer programme). Press to select the set­ting modes from the on screen menu.
43. h (REV/REW) Button
DVD mode [page 35]
Press to view the DVD picture in fast reverse motion or to reverse playback of an Audio CD.
VCR mode [page 24]
Press to rewind the tape, or to view the picture rapid­ly in reverse during the playback mode (Rewind Search). Press to cancel a setting of timer pro­gramme. Press to correct digits when setting pro-
B
Button to resume normal
) (DVD) [page 36]
pressing
–10–
EN
2C15
gramme (For example: setting clock or timer pro­gramme). Press to add or delete channel numbers dur­ing channel preset.
44. F(PAUSE/STILL) Button
DVD mode [page 34]
Press to pause Disc playback. Press repeatedly to advance the DVD picture step by step (or one frame at a time).
VCR mode [page 24]
While recording, press to temporarily stop the recording (pause). Press a second time to resume normal recording. You can not pause a One Touch Recording. Or, press during tape playback to freeze the picture. Press to advance the picture one frame at a time during still mode.
45. g(ENTER/FWD/F.FWD) Button
DVD mode [page 36]
Press to fast forward the Disc. Press the F Button, then press this Button to begin slow motion play­back. Press this Button repeatedly to change the forward speed of slow motion.
VCR mode [page 21]
Press to rapidly advance the tape, or view the pic­ture rapidly in forward during playback (Forward Search). When setting programme (For example: setting clock or timer programme), press to deter­mine your selection and proceed to the next step you want to input. Press to determine the setting modes from the on screen menu. Press to add or delete channel numbers during channel preset.
46. B(MENU SELECT/PLAY) Button
DVD mode [page 33]
Press to begin playback.
VCR mode [page 24]
Press to begin playback. Press to enter digits when setting programme (For example: setting clock or timer programme). Press to select the setting modes from the on screen menu.
47. CH Buttons (L/K) (VCR) [page 17,25]
In VCR mode, press to change TV channels on the DVD/VCR; press to adjust the tracking during nor­mal or slow motion playback; press to remove verti­cal jitter in a Still picture.
48. REC Button (VCR) [page 25]
Press once to start a recording.
49. SPEED Button (VCR) [page 25]
Press to select the VCR’s recording speed (SP or LP).
50. VCR Button [page 15]
Press to select VCR mode for the remote control.
You can switch the output mode of the DVD/VCR
either by pressing the OUTPUT Button on the front panel, or by pressing the DVD or the VCR Button on the remote control. However,
only the OUTPUT Button on the front panel does not switch the output mode of the remote control. If you want to use the remote control, you always need to select the correct output mode on the remote control, too.
51.
SETUP Button [page 43]
Press to enter the setup mode.
52. SUBTITLE Button [page 41]
Press to select the desired subtitle language.
53. TOP MENU/VIDEO Plus+ Button
DVD mode [page 34]
pressing
Press to bring up the Top Menu on a disc.
VCR mode [page 29]
Press to programme timer recording with the VIDEO Plus+ system.
54. DISPLAY Button
DVD mode [page 39]
Press to access or remove the display screen during DVD or Audio CD playback.
VCR mode [page 26]
Press to access or remove the VCR’s on-screen sta- tus display.
55. AUDIO Button
DVD mode [page 40]
Press
to select a desired audio language or sound
mode.
VCR mode [page 20]
Press to select a desired sound mode.
56. Number Buttons
DVD mode [page 35]
Press to directly select a Track (Audio CD) for playback. Press to programme Tracks (Audio CD) for play­back.
+10 Button:
When searching a TITLE, a CHAPTER, or a TRACK, use this button to enter numbers 10 and above. For example when entering ‘15’, press this button first, then press ‘5’.
VCR mode [page 22]
Press to select TV channels on the DVD/VCR. To select channels, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0 then 6.
DAILY/WEEKLY Button:
Press to select once, daily, everyday, or weekly when you programme the automatic timer record­ing using the VIDEO Plus+ system.
57. OPEN/CLOSE Button (A) [page 33]
Press to insert discs into or remove them from the tray.
58. SEARCH MODE/QUICK-FIND Button
DVD mode [page 35]
Press to access or remove the Search display, which allows you to go directly to a specific Title/Chapter/Track/Time.
VCR mode [page 30]
Press to use Quick-Find mode.
English
–11–
EN
2C15
A-B REPEAT
REPEAT
MODE
ZOOM
ANGLE
SUBTITLE
AUDIO
DISPLAY
QUICK-FIND
SEARCH MODE
CLOSE
OPEN/
21 3
87 9
54 6
0
+10
DAILY/WEEKLY
CLEARC. RESET
MENU
TOP MENU/VIDEO Plus+
RETURN
POWER/STANDBY Button
A-B REPEAT Button
REPEAT Button
MODE Button
SUBTITLE Button
DVD VCRCD
Turns the DVD/VCR on and off.
Turns the player on and off. Turns the DVD/VCR on and off.
Marks a segment to repeat between A and B.
Marks a segment
to repeat between A and B.
Allows you to repeat play a Chapter or Title.
Allows you to repeat play a Track or Disc.
ZOOM Button
To set black level on/off.
To set surround on/off.
Allows you to program
a specific order or random playback.
To magnify part of picture (x2/x4)
ANGLE Button
Accesses various camera angles on a disc.
Accesses various subtitles on a disc.
AUDIO Button
DISPLAY Button
Accesses various audio functions on a disc.
To select STEREO, L-CH or R-CH.
To select STEREO, L-CH, R-CH, or NORMAL.
Displays the current disc mode. Displays the current disc mode. Displays the current time, tape counter, channel.
To search chapter or time.
To rapidly return to
a location of disc.
• Το Search markers.
OPEN/CLOSE Button
To search track or time.
To rapidly return to
a location of disc.
SEARCH MODE/ QUICK-FIND Button
Number Buttons
CLEAR/C.RESET Button
To open or close the disc tray. To open or close the disc tray.
To select chapter directly.
To select track directly,
use display function, or input program order.
Clear the makers.
Clear the makers.
Removes status No.
in program input.
Tour of the Remote Control
Buttons on remote control work in different ways for DVD, CD and VCR : Refer to the following table for correct use.
Clear the number that is
entered incorrectly.
• Το Search markers.
Clear the number that is
entered incorrectly.
MENU Button
Brings up the Menu on a disc.
TOP MENU/VIDEO Plus+ Button
Brings up the Top Menu on a disc.
RETURN Button
Returns to a previous menu.
To search and confirm the
contents of the recorded programme(s).
To select channel.
To reset the tape counter.
Brings up the VCR Menu.
To programme timer recording
with the VIDEO Plus+ system.
–12–
EN
2C15
SETUP
SKIP
ENTER
Tour of the Remote Control
DVD
VCR
SLOW
REC
CH
SURROUND
ENTER/Arrow Buttons
DVD MODE: (REV/FWD) Button VCR MODE: (REW/F.FWD) Button
DVD MODE:
SKIP Buttons
VCR MODE:INDEX SEARCH/
TIME SEARCH
Button
DVD VCRCD
Moves the cursor and determines its position.
SETUP Button
Brings up the DVD player's Setup menu.
CH Buttons
To skip Chapters.
Allows you to search
forward/backward through a disc (×2. ×8. ×30. ×60) .
MENU SELECT/STOP Button
MENU SELECT/
PLAY Button
To stop playback.
Begin disc play.
PAUSE/STILL Button
Advances playback one frame at a time.
Advances playback one frame at a time.
Moves the cursor and determines its position.
Brings up the DVD player's Setup menu.
To skip Tracks. To perform INDEX or TIME
SEARCH.
Allows you to search forward/backward through a disc (×16) .
To stop playback.
Pause disc play.
Pause disc play.
Pause tape play or record.
Begin disc play.
To stop playback or record.
To change channels.
To select an item
in the VCR Menu.
To select an item in the VCR Menu.
Begin tape play.
DVD Button
To use the remote contorol in DVD mode.
To select the DVD output mode.
To select the VCR output mode.
To use the remote contorol
in VCR mode.
To view the tape in slow motion.
To start a recording.
VCR Button
SLOW Button
REC Button
Allows you to forward/backward
through a tape.
To return(advance) to a
previous(next) VCR Menu.
To activate the 3D sound.
SURROUND Button
SPEED
To select the recoeding speed.
SPEED Button
English
–13–
EN
2C15
DISPLAY
Stays on when the inserted disc is being played back.
Lights up when a CD is inserted on the tray.
Lights up when a DVD is inserted on the tray.
Lights up when the inserted disc comes to a pause.
Stays on when the A-B repeat function is on.
Stays on when the repeat function is on.
Displays how long a current title or track has been played back. When a chapter or track has switched, the number of a new title, chapter or track is displayed.
Power on
No disc inserted
Tray open
Tray closed
Loading the Disc
Power off
DISPLAYS DURING
OPERATION
LOADING THE BATTERIES
1. Open the battery compartment cover.
2. Insert two AA batteries, with each one oriented cor­rectly.
3. Close the cover.
Notes
¡Do not mix alkaline and manganese batteries. ¡Do not mix old and new batteries.
–14–
EN
2C15
VCR/DVD SWITCHING
Since this product comprises VCR and DVD players, it is necessary to select the correct output mode.
SWITCHING TO VCR MODE
Press the VCR Button on the remote control. (Verify that the VCR OUTPUT Light is lit.)
Press the DVD Button on the remote control. (Verify that the DVD OUTPUT Light is lit.)
SWITCHING TO DVD MODE
Notes
¡Pressing only the OUTPUT Button on the front panel does not switch the mode of the remote control. You
always need to select the correct mode on the remote control too.
¡The DVD operation Buttons and the VCR operation Buttons work separately.
SEARCH MODE/
OPEN/ CLOSE
VIDEO IN
CHANNEL OPEN/ CLOSE
DVD VCR
OUTPUT
TIMER SET
L
(mono)
STANDBY
R
CST.IN
AUDIO IN
DVD OUTPUT Light
VCR OUTPUT Light
A-B REPEAT
REPEAT
MODE
ZOOM
ANGLE
MENU
QUICK-FIND
1
4
7
CLEAR/C.RESET
AUDIO
SUBTITLE
TOP MENU/VIDEO Plus+
3
2
56
9
8
DAILY/WEEKLY
0
+10
DISPLAY
English
DVD VCR
OUTPUT
OUTPUT Button
–15–
DVD Button
VCR Button
ENTER
RETURN
DVD
SLOW SPEED REC
SKIP CH
INDEX SEARCH TIME SEARCH
MENU SELECT
DV-PMPF2E(UK)
SURROUND
SETUP
VCR
ENTER
EN
2C15
AERIAL
RF OUT
R
L
COAXIAL OPTICAL
S-VIDEO
OUT
DVD
ANALOG
AUDIO OUT
DIGITAL
AUDIO OUT
AV1 (TV)
AV2 (DECODER)
DVD/VCRVCR
3425
1
7698
REAR VIEW
HOOKUPS
DESCRIPTION-REAR PANEL
1. AC POWER CORD
Connect to a standard AC outlet to supply power to the DVD/VCR.
2. AERIAL Jack
Connect your antenna, Cable Box, or Direct Broadcast System.
3. RF OUT Jack
Use the supplied RF coaxial cable to connect this jack to the ANTENNA IN Jack on your TV.
4.
AV2 (DECODER)
Socket
Connect 21-Pin scart cable here and to the 21-Pin scart jack of a decoder.
5. AV1 (TV)
Socket
Connect 21-Pin scart cable here and to the 21-Pin scart jack of a TV.
6. ANALOG AUDIO OUT Jacks (DVD only)
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Connect the supplied audio cables here and to the Audio In jacks of a television or other audio equipment.
7. S-VIDEO OUT Jack (DVD only)
Connect an optional S-Video cable here and to the S-Video In jack of a television.
8.
DIGITAL COAXIAL AUDIO OUT
Jack
Connect an optional coaxial digital audio cable here and to the Coaxial Digital Audio In jack of a decoder or audio receiver.
9.
DIGITAL OPTICAL AUDIO OUT
Jack
(DVD only)
Connect an optional optical digital audio cable here and to the Optical Digital Audio In jack of a decoder or audio receiver.
“DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
(DVD only)
–16–
EN
2C15
The following show examples of connections commonly used to connect the DVD/VCR to TV and other
RF OUT
AERIAL
to AERIAL
to RF OUT
(Back of the unit)
to aerial socket
(TV)
UHF
AERIAL
RF OUT
R
L
COAXIAL OPTICAL
S-VIDEO
OUT
DVD
ANALOG
AUDIO OUT
DIGITAL
AUDIO OUT
AV1 (TV)
AV2 (DECODER)
DVD/VCRVCR
to 21-Pin
to 21-Pin Scart Jack
Decoder (Not supplied)
(TV)
to RF OUT
to aerial
socket
Scart Jack
AV2 (DECODER)
AV1 (TV)
components.
Notes
¡Be sure to turn off the power to all components in the system before connecting another component.
¡Refer to the Instruction Manuals for your TV, stereo system and any other components to be connected to the
DVD/VCR.
English
DVD/VCR TO TV CONNECTION
1. Disconnect the TVs power cord from the AC outlet.
2.
Disconnect the UHF TV aerial coaxial cable from the TV
3. Connect the UHF TV aerial coaxial cable to the
DVD/VCR.
4. Connect the DVD/VCR to the TV using the coaxial
cable.
5. Plug the Power cords of the DVD/VCR and TV into the
AC outlets.
OTHER CONNECTIONS
EURO SCART (AV) SOCKETS
Your DVD/VCR is provided with two Scart sockets which you may connect to other external devices with Scart sock-
.
ets. We recommend this connection to ensure a better audio and picture quality. NICAM stereo sound is only achieved when using a SCART lead.
Euro Scart cables are obtainable at your dealer.
AV1 (TV) CONNECTION TO TV
If your TV has Scart sockets, you may connect your DVD/VCRs AV1 (TV) scart socket to the Scart socket on the back of your TV. Please see the instruction manual for your TV.
AV2 (DECODER) CONNECTION FOR OTHER EXTERNAL DEVICES
The second Scart socket AV2 (DECODER) is designated for other external devices, e.g. decoder, another VCR, video camera and so on.
NOTE:
If you want to connect a TV with Scart socket to your
DVD/VCR, the TV must be connected to the DVD/VCR through AV1 (TV). A connection to AV2 (DECODER) will not function correctly.
EXTERNAL INPUT MODE
To receive the signal from an external input (decoder, video camera, another VCR etc.), connect to the AV2 (DECODER) socket, and press the CH Buttons (o/p) or enter 002 with the Number Buttons to show “AV 2 ” on the TV screen. If you use the AV1 (TV) socket, press CH Buttons (o/p) or enter “001” with the Number Buttons to appear “AV 1 ” on the TV screen. If you use the front AUDIO/VIDEO In Jacks, press the CH Buttons (o/p) or enter 003 with number button to show
AV 3 on the TV screen.
–17–
EN
2C15
RL
ANALOG
AUDIO OUT
R
L
CONNECTION TO AN AUDIO SYSTEM
COAXIAL OPTICAL
DIGITAL
AUDIO OUT
COAXIAL OPTICAL
or
Method 1
Stereo system
AUDIO
DVD/VCR
Method 1 DVD/VCR + Stereo system
Method 2 DVD/VCR + Dolby Digital decoder or DTS decoder
Audio Input Jacks
Analog Audio Out (DVD only)
Method 2
Dolby Digital decoder
or
DTS decoder
Digital Audio Input Jacks
Digital Audio Out
Notes
¡If output Dolby Digital audio, connect to a Dolby Digital decoder, and set Dolby Digital to on for audio out-
put in the setup mode. (See page 45)
¡If output DTS audio, connect to a DTS decoder, and set DTS to ON for audio output in the setup mode. (See
page 45)
¡Unless connected to a Dolby Digital decoder, or a DTS decoder, set Dolby Digital or DTS to off for audio out-
put in the setup mode. Playing a DVD using incorrect settings may generate noise distortion, and may also damage the speakers. (See page 45)
¡The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital sound
by an MD or DAT deck.
¡Set Dolby Digital and DTS to off for audio output in the setup mode for method 1 only. Playing a DVD using
incorrect settings may generate noise distortion, and may also damage the speakers. (Refer to page 45 to set ON for Dolby Digital and DTS)
¡If you use the OPTICAL jack, remove the protective cap.
–18–
EN
2C15
CONNECTION TO A TV (FOR DVD/VCR)
R L S-VIDEO IN
or
AV1 (TV)
ANALOG
AUDIO OUT
R
L
S-VIDEO
OUT
Method 1
Basic Audio
Best picture
TV
AV Cable
S-Video
Cable
DVD/VCR
Analog Audio out
(DVD only)
Method 1 DVD/VCR Player + TV with S-Video Input Jack
Method 2 DVD/VCR Player + TV with 21 pin scart Jack
S-Video out
(DVD only)
Method 2
Good picture
English
21 pin Scart jack
Euro audio/video Cable
EURO Audio/Video out
Notes
¡If you use the Euro audio/video cable, it is not necessary to connect the analog audio cable.
¡Connect the DVD/VCR player directly to a TV. If the A/V cables are connected to a DVD/VCR, pictures may
be distorted due to the copy protection system.
HOW TO CONNECT TO A TV WITHOUT AUDIO/VIDEO INPUT JACKS
If your TV does not have a Scart jack, it is still possible to connect this DVD/VCR player to your TV’s 75- ohm coaxial antenna terminal using a commercially available Stereo Audio/Video RF Modulator, not includ­ed. Connect the audio and video outputs of the DVD/VCR player to the audio and video inputs on the RF Modulator, and then connect the coaxial output of the RF Modulator (usually marked TO TV) to the 75 ohm coaxial antenna terminal on your TV. Follow the instruction supplied with the RF Modulator for more details.
If your TV’s 75 ohm coaxial antenna terminal is already occupied by an antenna or cable box connection, remove that cable from your TV’s antenna terminal and reconnect it to the coaxial antenna input terminal of the RF Modulator (usually marked ANT IN), then connect the RF modulator to your TVs antenna terminal as described above.
Note
¡The picture quality from DVD discs will not be as good if the DVD/VCR player is connected to the TV’s
antenna terminal through an RF Modulator.
–19–
EN
2C15
During reception of bilingual broadcasts:
Display on
the TV screen
Mode
MAIN
SUB
MAIN
SUB
MAIN
SUB
MAIN
SUB
Main Audio Main Audio Sub Audio Sub Audio Main Audio Sub Audio
L R L R L R
AUDIO OUTPUT
Reception of stereo broadcasts:
STEREO
LEFT
RIGHT
- None -
Display on
the TV screen
Mode
Stereo
L
R
Monaural
L Audio R Audio L Audio L Audio R Audio R Audio
L+R Audio L+R Audio
L R L R L R
L R
AUDIO OUTPUT
During playback of the recorded tape in Hi-Fi mode:
Mode
Stereo
L
R
Normal
STEREO
LEFT
RIGHT
- None -
Display on
the TV screen
Hi Fi L Audio Hi Fi R Audio Hi Fi L Audio Hi Fi L Audio Hi Fi R Audio Hi Fi R Audio
Normal Audio Normal Audio
L R L R L R
L R
AUDIO OUTPUT
MENU
TIMER SET UP INITIAL
RF OUT CH 35
INITIAL
CH TUNING CLOCK RF OUT
HI-FI STEREO SOUND SYSTEM
This DVD/VCR will record and playback Hi-Fi stereo sound. In addition it has a NICAM stereo sound decoder. This equipment will receive stereo and bilingual broadcasts and there are several ways of recording and play­ing back the sound.
SELECTING THE SOUND MODE
VCR
You can select each mode by pressing the AUDIO Button on the remote control. Each mode is indicated on the TV screen as following.
Notes
¡If you play non-Hi-Fi tapes, the DVD/VCR will play automatically in monaural even if you select any mode. ¡If the stereo signal becomes weak, the broadcast is automatically recorded in monaural.
VIDEO CHANNEL SETTING
Skip This Section When Connected By SCART. Video channel setting will be necessary, if your DVD/VCR is connected to the TV via the coaxial cable.
Use the remote control for this procedure.
1 Insert a pre-recorded tape into the
DVD/VCR.
The DVD/VCR will turn on and start playback automatically. If playback does not start, press the B Button.
2 Select and adjust your TV to channel 35.
If the playback picture appears on the TV screen, continue with step 8.
If channel 35 is employed for broadcasting, or interference lines appear on the picture, the RF converter must be set to a different channel between CH22 and CH69. Continue with step 3.
3 Press the MENU Button. 4 Press the B or C Button repeatedly to
select “INITIAL”. Then, press the
g Button.
PRESET FOR USE
VCR
5 Press the B or C Button repeatedly to
select to “RF OUT”. Then, press the Button.
The RF OUT CH menu will appear.
6 Press the B or C Button to select a channel
which is not used for broadcasts between channel 22 and channel 69 in your area, then press the
g Button.
7 Press the MENU button to exit.
Set the TV channel to the RF OUT CHANNEL which was selected on the DVD/VCR. Press B. A picture from the DVD/VCR will appear on the TV screen. If a picture does not appear, repeat steps 3 to 7 using a different channel which is not used for broadcasts.
8 Press C to stop the tape.
Notes
–20–
You may also access the RF OUT CH menu by
pressing and holding MENU on the remote control for 3 seconds during power off until the RF OUT CH menu appears.
If your DVD/VCR and TV are connected using a SCART cable there is no need to have the RF con­verter operating so it can be switched off and avoid the possibility of interference.
g
EN
2C15
SETTING THE CLOCK
INITIAL
CH TUNING CLOCK RF OUT
CLOCK
YEAR 2 0 0 2 MONTH 0 1 DAY 0 1 TU HOUR
_ _
MINUTE
_ _
MENU
TIMER SET UP INITIAL
VCR
This DVD/VCR incorporates a 24-hour clock. The clock must be set for the Automatic Timer Recording function to operate correctly.
If your DVD/VCR is fitted out with PDC and the PDC signal is available in your area, your DVD/VCR can get the current time from your local PDC broadcast. It keeps track of the time constantly referring to the time broadcasted by your PDC broadcast. If you want to use this feature, refer to AUTO CLOCK SETTING in the next section.
MANUAL CLOCK SETTING
1 Press the MENU Button.
2
Press the Bor C Button to select “INITIAL”, then press the
3
Press the B or C Button to select “CLOCK”, then press the
4
Press the B or C Button to select “MANUAL”.
5
Press the B or C Button until the relevant year appears, then press the Button.
gButton.
g Button.
g
6 Likewise, set the relevant month, day, hour,
and minute.
7 Press the MENU Button to start the clock.
Notes
In the steps 5 and 6, you can go back to the item you want to correct by pressing the
h Button.
Although seconds are not displayed, they begin counting from 00 when you exit by pressing MENU Button. Use this feature to synchronise the clock with the correct time.
When unplugging the power-cord or if there is a power failure for more than one minute, you may have to reset the clock.
AUTO CLOCK SETTING
1 Follow the steps through 1 to 3 in MANUAL
CLOCK SETTING”.
2 Press the B or C Button to select AUTO”.
3 Turn off the DVD/VCR once by pressing the
(Standby/Power ON) Button.
The clock will appear on the TV screen when you turn on the DVD/VCR again.
Notes
Channel Presetting must be set before the Auto Clock is set.
The DVD/VCR refers to the channel which was memorised into position 01. The PDC channel must therefore be set to position
01.
The clock cannot be set automatically if you are not receiving a channel that carries a time signal in your area. In this case, set the clock manually.
Once the auto clock setting is performed, the DVD/VCR will correct the current time by receiv­ing PDC broadcasts whenever you turn off the DVD/VCR.
The DVD/VCR will correct the current time auto­matically at 8:00.
Between 23:00~1:00, the AUTO CLOCK function does not work even if the DVD/VCRs power is turned off.
English
Tuning of broadcast channels not already preset in the DVD/VCR can be performed in two ways.
AUTOMATIC TUNING
By AUTOMATICALLY tuning channels and placing them in sequential order in the DVD/VCR’s memory i.e. the first channel found will be memo­rised into the DVD/VCRs channel position 1, the second channel found will be memorised into the DVD/VCRs channel position 2 and so on.
Execution of the Automatic tuning cancels all the preset channels. DO NOT use this feature if you intend to use some of the pre-tuned channels. Use the Manual tuning function to tune in the addi­tional channels you require.
TUNING
MANUAL TUNING
Each channel is tuned manually and individually. Follow the steps laid out in the MANUAL TUN­ING section.
Before you preset Channel ...
It is necessary to set the video channel if your DVD/VCR is connected to the TV via the coaxial cable, and TV channel 35 is employed for broadcast­ing, or interference lines appear on the picture. Please refer to Video Channel Setting”.
–21–
EN
2C15
MENU
TIMER SET UP INITIAL
INITIAL
CH TUNING CLOCK RF OUT
CH TUNING
AUTO MANUAL MOVE
MENU
TIMER SET UP INITIAL
INITIAL
CH TUNING CLOCK RF OUT
CH TUNING
AUTO MANUAL MOVE
MANUAL
POSITION CHANNEL DECODER SKIP
P08
008 [OFF] [OFF]
AUTOMATIC TUNING
VCR
You can programme the tuner to scan only the chan­nels that you can receive in your area.
Use the remote control for this procedure.
1 Turn on the TV and select the TV channel to
the video channel on the TV.
2 Press the MENU button.
3 Press the B or C Button to select INI-
TIAL”, then press the
g Button.
4 Press the B or C Button to select CH TUN-
ING, then press the
g Button.
5 Press the B or C Button to select “AUTO,
then press the
The tuner scans and memorises all the active chan­nels in your area. After scanning, the tuner stops on the lowest memorised channel.
To Select a Desired Channel
You can select a desired channel by using the CH Buttons (o/p), or directly pressing the Number Buttons on the remote control.
Enter a channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0 and 6. If you only press 6, channel 6 will be selected after a brief delay.
You can only select channels 1–99.
g Button.
MANUAL TUNING
VCR
Use the remote control for this procedure.
1 Press the MENU Button.
2 Press the B or C Button to select INI-
TIAL”, then press the
g Button.
3 Press the B or C Button to select CH TUN-
ING, then press the
g Button.
4 Press the B or C Button to select “MANU-
AL”, then press the Button.
g
5 Press the B or C Button to select “POSI-
TION, then press the
g Button.
When a weak signal is received in Manual Tuning mode, you can change the background to solid blue or the static screen by pressing the C. RESET Button.
6 Press the Number, B, or C Button to select
your desired position number, then press the
g Button.
You can select position number 01-99.
If [ON] appears on the right side of SKIP, press the
B or C Button to point to SKIP. Then, press the g Button to select [OFF].
If you want to remove scrambled signals, press the B or C Button repeatedly to point to DECODER. Then, press the g Button to select [ON].
7 Press the B or C Button to select CHAN-
NEL”, then press the
g Button.
8 Press the B or C Button to start scanning.
The DVD/VCR tuner will begin to search up or down automatically. When a channel is found, the DVD/VCR will stop searching and the picture will appear on the TV Screen.
You can select desired channel number by using the Number Buttons. You must refer to the channel plan and press three digits to select the channel number. (To select channel 24, first press the “0” Button and then press “2” and “4”).
If this is the channel you want, press the gButton.
Channel Plan
CH Indication TV Channel
01 – 10 IRA-IRJ, gap
21 – 69 E21 – E69
74 – 78 S01
80 – 100 S1 – S20, gap
121 – 141 S21 – S41
~ S03, X, Y
9 Press the MENU Button to exit.
Note
To confirm that a channel has been added, press the CH Buttons (o/p).
–22–
EN
2C15
MENU
TIMER SET UP INITIAL
INITIAL
CH TUNING CLOCK RF OUT
CH TUNING
AUTO MANUAL MOVE
MANUAL
POSITION CHANNEL DECODER SKIP
P08 008
[OFF]
[ON]
MENU
TIMER SET UP INITIAL
INITIAL
CH TUNING CLOCK RF OUT
CH TUNING
AUTO MANUAL MOVE
MOVE
P01: P02: P03: P04: P05:
01 02 03 04 05
P06: P07: P08: P09: P10:
06 07 08 09 10
[ ]
MOVE
P01: P02: P03: P04: P05:
01 02 03 04 05
P06: P07: P08: P09: P10:
06 07 08 09 10
Position Number
Channel Number
[ ]
TO SKIP A PRESET CHANNEL CHANNEL ORDER
VCR
The channels you can no longer receive or seldom watch can be set to be skipped when you access chan­nels the CH Buttons (o/p).
Use the remote control for this procedure.
1 Press the MENU Button.
2 Press the B or C Button to select INI-
TIAL”, then press the
g Button.
3 Press the B or C Button to select CH TUN-
ING, then press the
g Button.
4 Press the B or C Button to select “MANU-
AL”, then press the
g Button.
VCR
Your TV stations will not necessarily be stored in the usual order: BBC1, BBC2, ITV, CH4 and CH5.
You can arrange the channels in any order you want as follows.
Use the remote control for this procedure.
1 Press the MENU Button.
2 Press the B or C Button to select INI-
TIAL”, then press the
g Button.
3 Press the B or C Button to select CH TUN-
ING, then press the
g Button.
4 Press the B or C Button repeatedly to
select MOVE, then press the
g Button.
English
5 Press the B or C Button to select “POSI-
TION, then press the
g Button.
6 Press the Number, B, or C Button to select
relevant position number, then press the
g Button.
7 Press the B or C Button to select SKIP”,
then press the
To memorise the channel again, press the gButtonON will change to OFF”.
g Button to select [ON].
8 Press the MENU Button to exit.
Note
To confirm that a channel has been deleted, press the CH Buttons (o/p).
5 Press the B or C Button repeatedly to
select the position number you want to change the channel, then press the
g
Button.
You cannot select a position number where - - appears next to the number. This is because SKIP is set to [ON] for this position number.
When a weak signal is received in Channel Order mode, you can change the background to static blue by pressing the C. RESET Button. If you press the button again, the background will return to the static screen.
6 Press the B or C Button repeatedly until
the channel move to another position num­ber, then press the
g
Button.
7 Press the MENU Button to exit.
–23–
EN
2C15
BASIC OPERATIONS
PLAYBACK
VCR
1 Turn on the TV and select the video channel
on the TV.
2 Insert a prerecorded tape.
The DVD/VCR will turn on automatically. If the erase-protection tab has been removed, the DVD/VCR will start playback automatically.
3 Press the B Button to begin playback.
TRACKING ADJUSTMENT
Tracking adjustment will be activated automatically (Digital Tracking function) when you start playback. To adjust the tracking manually, press the CH Buttons (o/p).
you can reduce the noise lines by pressing the CH Buttons (o/p) in Slow mode, too. Slow tracking adjustment is not set automatically.
In the Still mode, press the SLOW Button, and press the CH Buttons (o/p) until the streaks disappear. To return to the Still mode, press the F Button again.
IF A TAPE IS ALREADY IN THE DVD/VCR Using the buttons on the DVD/VCR
Just press the B Button on the DVD/VCR. Power will automatically turn on and playback will start. (Direct Button Operation)
Using the buttons on the remote control
Press the (Standby/Power ON) Button to turn on, and then press the B Button.
4 Press the C Button to stop playback.
SPEED SEARCH
VCR
1 During playback, press the g or h
Button in the SP or LP modes to view a videotape at a high speed in either a forward or reverse direction. In this mode, the sound will be muted.
2 Press the button again, the DVD/VCR will
now search in super high speed. (in the LP mode only).
3 Press the B Button to return to normal play-
back.
STILL PICTURE
VCR
Press the F Button during playback to view a still pic­ture on the TV screen.
You can advance the picture by one frame by press­ing the the F Button repeatedly during the STILL mode.
When the picture begins to vibrate vertically, stabi­lize the picture by pressing the CH Buttons (o/p) in the STILL mode.
After the DVD/VCR has been in Still mode for 5 minutes, it will stop automatically to protect the tape and the video head.
<Note for Speed search and Still Picture”>
Usually there will be video noise lines (black and white streaks or dots) on the screen. This is normal. The still picture will, in addition to containing the "noise" lines, be black and white. This is not a fault of the machine but merely a by­product of the technology involved in producing a DVD/VCR with LP mode.
SLOW MOTION
Press the SLOW Button to reduce the playback speed. The DVD/VCR mutes the sound during slow motion. You can control the speed by pressing the
g(faster) or h(slower) Button. Press the B
Button to return to normal playback.
If it is left in the Slow mode for more than five min­utes, the DVD/VCR will automatically switch to the Stop mode.
–24–
VCR
EN
2C15
RECORDING
VCR
VIEWING AND RECORDING THE SAME PROGRAMME
1 Insert a cassette tape with its erase preven-
tion tab in place.
(If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)
2 Press the Number or CH Buttons (o/p) to
select the channel to be recorded.
3 Press the SPEED Button to select the tape
speed (SP/LP).
4 Press the REC Button to begin recording.
The REC indicator on the display comes on.
5 Press the C Button when recording is com-
pleted.
SKIPPING UNWANTED PROGRAMME MATERIAL DURING RECORDING
1 Press the F Button when you want to tem-
porarily halt recording.
You can check the remaining pause time with marks on the TV screen. Each mark represents one minute. After five minutes, the DVD/VCR will auto­matically switch to the Stop mode to prevent tape damage.
2 Press the F or REC Button to resume
recording.
RECORDING ONE PROGRAMME WHILE VIEWING ANOTHER
You can record one programme while viewing anoth­er. To start recording, follow steps 1 to 4 under Viewing and Recording the same Programme. Then, set the TV to the channel you want to watch.
TO MONITOR THE PROGRESS OF YOUR RECORDING
Select the video channel on the TV.
ASSEMBLE FUNCTION
You can record in continuation from previous pro­gramme on a pre-recorded tape.
1 Insert a pre-recorded tape. Press the B
Button to start playback.
2 Press the F Button at the desired point on
the tape.
3 Press the REC Button. The DVD/VCR will be
the recording pause mode.
4 Press the CH Buttons (o/p) to select the
channel to be recorded .
5 Press the REC or F Button. The recording
will begin.
6 Press the C Button when recording is com-
pleted.
English
–25–
EN
2C15
SET UP
AUTO REPEAT[ON
]
PICTURE[NORMAL
]
AUTO RETURN
MENU
TIMER SET UP INITIAL
MENU
TIMER SET UP INITIAL
SET UP
AUTO REPEAT PICTURE[NORMAL
]
AUTO RETURN
ADVANCED OPERATIONS
OTR
(ONE TOUCH RECORDING)
VCR
This function enables you to set the duration of a recording simply by pressing the REC button on the DVD/VCR.
1
Follow steps 1 to 3 in “VIEWING AND RECORD- ING THE SAME PROGRAMME” section.
2 Press the REC Button on the DVD/VCR
repeatedly until the desired recording length appears.
0:30 1:00.... 7:30 8:00
REC (Normal recording)
Recording stops when 0:00 is reached.
TO CHECK TIME REMAINING DURING AN OTR
Press the DISPLAY Button.
TO CHANGE THE RECORDING LENGTH DUR­ING AN OTR
Press the REC Button until the desired length appears.
TO STOP AN OTR BEFORE RECORDING IS FIN­ISHED
Press the C Button.
TO CANCEL THE OTR BUT CONTINUE RECORDING
Press the REC Button repeatedly until REC appears in the upper left corner of the TV screen.
If a tape ends during OTR, the DVD/VCR will stop, eject the tape, and switch to the DVD mode automati­cally as the TIMER SET light blinks. (If the DVD power is off, the DVD/VCR will become STANDBY status).
When OTR is finished, the TIMER SET Light blinks. To use the DVD/VCR again, press the TIMER SET Button on the DVD/VCR.
AUTO REPEAT PLAYBACK
2 Press the B or C Button to select SET
UP, then press the
gButton.
3 Press the B or C Button to select “AUTO
REPEAT”.
4 Press the g Button so that “ONappears
next to “AUTO REPEATon the TV screen.
When in Stop mode, Auto Repeat mode will start automatically. If the on-screen menu still remains, press MENU to exit.
Notes
Once you select the Auto Repeat mode, it stays in effect even after you turn off DVD/VCR.
TO STOP PLAYBACK
Press the C Button.
TO EXIT THE AUTO REPEAT MODE
Repeat steps 1 to 3. Then, press the g Button. ON will then disappear from the menu. Press the MENU button to exit.
PICTURE SELECT
VCR
This function enables you to select the picture quality of a tape.
Use the remote control for this procedure.
1 Press the MENU Button.
2 Press the B or C Button to select SET
UP, then press the
g Button.
The DVD/VCR has an auto repeat function that allows you to repeat a tape indefinitely without touch­ing B Button.
Use the remote control for this procedure.
Insert a pre-recorded tape.
1 Press the MENU Button.
VCR
3 Press the B or C Button to select PIC-
TURE.
4 Press the g Button until the desired
mode (NORMAL, SOFT, or SHARP) is indi­cated on the TV screen.
Note
Once you select the Picture Select mode, it stays in effect even after you turn off the DVD/VCR.
–26–
EN
2C15
AUTOMATIC OPERATION
MENU
TIMER SET UP INITIAL
TIMER NUMBER
1
START END
DATE
CHANNEL
PDC
SPEED
--/--
--:--
--:--
--
--
--
AUTOMATIC REWIND&EJECT
When the end of a tape is reached during recording, playback, or fast-forward, the tape will automatically rewind to the beginning. After that, the DVD/VCR will eject the tape.
The tape will not auto-rewind during timer recording or One Touch Recording.
TAPE EJECT
A tape can be ejected with the DVD/VCR power on or off (but the DVD/VCR must be plugged in).
If a timer recording is set, you have to press the TIMER SET Button first, and then press the C (STOP/EJECT) Button on the DVD/VCR to eject the tape. To activate the Timer Recording again, Insert a tape and then press the TIMER SET Button.
REAL TIME TAPE COUNTER
This shows the elapsed recording or playback time in hours, minutes, and seconds. (Nothing is shown in the case of blank portion)
The indication will appear when the tape is rewound further than the tape counter position 0:00:00.
TIMER RECORDING
You may programme the DVD/VCR to start and end a recording while you are away. You can set eight pro­grammes to record on specific days, daily or weekly within a 1 year period.
Use the remote control for this procedure.
Insert a cassette tape with its erase prevention tab in
place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)
1 Press the MENU Button.
2 Press the B or C Button to select TIMER”,
then press the Button.
Notes
If you have not set the clock yet, CLOCK setting menu appears. If so, follow the steps outlined in the
Setting the Clock section. Then, set the timer.
When you press the g Button after pressing the
the B or C Button during steps 3 to 10,the input mode will move to the next step.
If you do not press the g Button within 5 seconds of setting an item, the input mode will move to the next step.
Press the h Button to go back one step from the current setting during steps 4 to 10. If the h Button is pressed when the TIMER NUMBER is flashing, the entire programme contents will be erased.
g
VCR
VCR
VCR
3 Programme number flashes. Press the B or
C Button repeatedly until the desired pro­gramme number appears. Then, press the
g Button.
4 Select once, daily, everyday, or weekly
recording.
For once-only recording: Press the B or C Button repeatedly until the relevant month appears. For daily recording: To record a TV programme at the same time on the same channel from Monday through Friday. While the month digit is flashing, press the B or C Button repeatedly to select For everyday recording:To record a TV programme at the same time on the same channel every day. While
/
A
the month digit is flashing, press the B or C Button repeatedly to select MO-SU”. For weekly recording: To record a TV programme at the same time on the same channel every week. While the month digit is flashing, press the B or C Button repeatedly to select “W-MO”
(Example: every monday)
5 For once-only recording only : Press the B
or C Button repeatedly until your desired day appears.
6 Press the B or C Button repeatedly until
the relevant start hour appears. Next, enter the minute digit.
7 Press the B or C Button repeatedly until
the relevant end hour appears. Next, enter the minute digit.
8 Press the B or C Button repeatedly until
the relevant channel number appears.
9 Press the B or C Button repeatedly until
your the desired tape speed appears.
10 Press the B or C Button repeatedly to set
PDC ONor OFF.
The Programme Delivery Control (PDC) is a very convenient system which assures that the TV pro­grammes you have programmed for timer recording will be recorded exactly from beginning to end (see page 29).
11 Press the g Button.
Programme 1 is now completed.
12 Press the MENU Button to exit.
To set another timer programme, repeat steps 3 to 11.
13 Press the TIMER SET Button to activate the
timer.
The TIMER SET light comes on.
As the TIMER SET light comes on the DVD/VCR
becomes STANDBY status, and switches to DVD mode automatically.
W
hen all timer recordings are finished, the TIMER SET light will flash. To use the DVD/VCR again as usual, press the TIMER SET Button to disable the flashing TIMER SET light, then Press the DVD or the VCR Button to choose DVD or VCR mode, then continue with the other features as described in this manual.
–27–
MO-FR
EN
2C15
English
.
.
TO STOP A TIMER PROGRAMME WHICH HAS
9:00 10:00 11:00
Programme 1
Programme 2
Programme 3
ALREADY STARTED
1 Press the C (STOP) Button on the
DVD/VCR.
Note
The C
/
A Button on the remote control will not func-
tion in the Automatic Timer Recording mode.
TO CORRECT TIMER PROGRAMMES
If you want to correct an automatic timer after you fin­ished setting programme,
1 Repeat steps 1 to 3 in the “TIMER
RECORDINGsection.
2 Select the setting you want to change
using the
g or h Button.
3 Enter the correct numbers using the B or
C Button.
4 Press the MENU Button to exit.
5 Press the TIMER SET Button to return to
timer stand-by mode.
TO CANCEL OR CHECK THE START/END TIME
1 Repeat steps 1 to 2 in the TIMER
RECORDING”.
2 Select a programme number you want to
check using the of selected programme appears on the TV screen. You may cancel the entire pro­gramme by pressing the
B or C Button. The details
h Button.
3 Press the MENU Button to exit.
HINTS FOR TIMER
RECORDING
VCR
¡If there is a power failure or the DVD/VCR is
unplugged for more than 1 minute, the clock setting and all timer settings will be lost.
¡If a tape ends during TIMER RECORDING, the
DVD/VCR will stop, eject the tape, and switch to the DVD mode automatically as the TIMER SET light blinks. (If the DVD power is off, the DVD/VCR will become STANDBY status).
¡
If a tape is not in the DVD/VCR or does not have a safe­ty tab, the TIMER SET light flashes and timer record­ing will not operate. Please insert a recordable tape.
¡
When timer recordings are set, the TIMER SET light will come on. To use the DVD/VCR as usual until the time for the recording, press the TIMER SET Button so that the TIMER SET light disappears. Press the DVD/VCR Button to choose VCR or DVD modes, then continue with the other features as described in this manual.
AVOID OVERLAP OF TIMER PROGRAMMES
A timer programme does not work while another pro­gramme is under execution.
–28–
EN
2C15
TIMER RECORDING USING
PlusCode
No.:---------
PlusCode
No.:123456789
TIMER NUMBER
1
START END
DATE
CHANNEL
PDC
SPEED
06/05 SA 19:30 20:30 16 SP OFF
TIMER NUMBER
1
START END
DATE
CHANNEL SPEED
06/05 SA
19:30 20:30 16 SP
PDC
OFF
®
THE VIDEO Plus+
You can programme the timer using the PlusCode programming numbers that are printed in TV guide magazine. You can set eight programmes to record.
Use the remote control for the this procedure.
Insert a cassette tape with its erase prevention tab in
place. (If necessary, rewind or fast forward the tape to the point at which you want to begin recording.)
1 Press the VIDEO Plus+
Button.
If you have not set the clock yet, CLOCK setting menu appears. If so, follow the steps outlined in the Setting the Clock section. Then, set the timer.
2 Press the Number Buttons to set the
PlusCode number of the programme you want to record.
Press the h Button to go back one digit from cur­rent digit while you set the PlusCode number.
3 Select once, daily, everyday, or weekly
recording.
For once-only recording:
Press the VIDEO Plus+ Button. For daily recording: To record a TV programme at the same time on the same channel from Monday through Friday. Press the DAILY/WEEKLY Button repeatedly to select DAILY (MO-FR), then, press the VIDEO Plus+ Button. For everyday recording:To record a TV programme at the same time on the same channel every day. Press the DAILY/WEEKLY Button repeatedly to select DAILY (MO-SU), then, press the VIDEO Plus+ Button. For weekly recording: To record a TV programme at the same time on the same channel every week. Press the DAILY/WEEKLY Button repeatedly to select WEEKLY, then, press the VIDEO Plus+ Button.
Note
If the PlusCode number is not available, it will be cleared automatically when you press the VIDEO Plus+ Button. Enter the correct PlusCode number and press the VIDEO Plus+ Button again.
If the PlusCode number flashes when you press the VIDEO Plus+ Button, this means that the PlusCode number you entered was incorrect or the timer recording you just programmed and another timer recording overlap.
4 Confirm the channel number, then, press
the
g Button.
SYSTEM
VCR
If your local channel information is programmed in DVD/VCRs memory, your local channel number appears automatically.
If your local channel information is not programmed in DVD/VCRs memory, “– –” or an incorrect chan­nel number may appear. In this case, press the B or
C Button repeatedly until your desired channel num-
ber appears. Then, press the g Button.
When you select the channel number using the B or
C Button, it memorises in DVD/VCR’s memory.
5
Press the Bor CButton repeatedly until the desired tape speed appears.
6
Press the Bor CButton to choose ONorOFF”.
The Programme Delivery Control (PDC) is a very convenient system which assures that the TV pro­grammes you have programmed for timer recording will be recorded exactly from beginning to end (see page 29).
7 Press the MENU Button to exit. 8 Press the TIMER SET Button to activate the
timer.
The TIMER SET light on the display comes on.
PDC(Programme Delivery Control)
The Programme Delivery Control (PDC) is a very convenient system which assures that the TV pro­grammes you have programmed for timer recording, will be recorded exactly from beginning to end, even if the actual broadcasting time differs from the sched­uled time due to delayed start or extension of the pro­gramme duration. Also, if a programme is interrupted and, for example, some special news is broadcast, the recording will also be interrupted automatically and resumed when the programme continues.
When the PDC signal drop out because the broadcast signal is weak, or when a broadcasting station does not transmit a regular PDC signal, the timer recording will be performed in the normal mode (without PDC) even if it was programmed for PDC. When the start­ing time of the PDC timer recording is from 0:00 to 3:59 on a given day, the PDC function operates from 20:00 on the previous day to 4:00 on the following day. When the starting time of the PDC timer record­ing is from 4:00 to 23:59 on the given day, the PDC function operates from 0:00 on the day to 4:00 on the following day. This means that if the relevant pro­gramme is broadcasted within this period, it will be recorded correctly. if the timer is not programmed cor­rectly, the incorrect timer setting stays in effect unless you cancel it. To cancel the incorrect timer setting, refer to TO CANCEL OR CHECK THE START/END TIME’’ on page 28.
–29–
English
VCR
EN
2C15
AUTO RETURN
VCR
If there are any remaining programmes including Daily, Everyday, & Weekly, AUTO RETURN will not operate.
1 Press the MENU Button. 2 Press the B or C Button repeatedly to
point to “SET UP”, then press the Button.
3 Press the B or C Button to point to “AUTO
RETURN, then press the
[AUTO] will appear next to AUTO RETURN”.
4 Press the MENU Button.
TO WATCH THE RECORDED TIMER PROGRAMME
Press the TIMER SET Button to cancel the Timer Stand-by. Then, Select VCR mode by pressing the VCR Button on your remote. Press the B Button.
g
g button.
2 Press the B, C or TIME SEARCH Button
(G)
repeatedly until the desired time
appears.
3 Press the h or g Button.
The DVD/VCR begins rewinding or fast forwarding to the specified point. When 0:00 is reached, the DVD/VCR will start play­back automatically.
Notes
Time Search can be set up to 9 hours 59 minutes (9:59). When you press the TIME SEARCH Button
(G)
in step 2, it will increase the time by 15 min­utes. In this case, Time Search can be set up to 9 hours 45 minutes (9:45).
This function will not operate in the Recording mode.
Operations must be followed up within 30 seconds, from steps 2 to 3. Otherwise the Time Search mode will be cancelled.
To exit the Time Search mode, press the MENU Button in step 2. Or press the C Button after step 3.
QUICK-FIND
VCR
This function enables you to search and confirm the contents of the recorded programme(s) using the index mark.
Use the remote control for this procedure.
The tape must be fully rewound.
1 Press the QUICK-FIND Button.
TO SKIP TO THE BEGINNING OF NEXT PRO­GRAMME
Press the QUICK-FIND Button.
TO VIEW AT NORMAL SPEED
Press the BButton. The Quick-Find is cancelled.
Notes
This function will not operate in the Recording mode.
When you want to cancel the Quick-Find while in progress, press the C Button.
When the end of a tape is reached during the Quick­Find, the tape will automatically rewind to the begin­ning. After rewinding finishes, the DVD/VCR will eject the tape.
TIME SEARCH
VCR
If a tape includes both programmes recorded in the PAL system and ones recorded in the NTSC system, this function may not be operated correctly.
Use the remote control for this procedure.
1 Press the TIME SEARCH Button
(G)
.
INDEX SEARCH
VCR
The index mark will be made automatically when REC is pressed. It will also be marked at the starting point of Timer recording and OTR.
The index mark is not recorded if the F Button is pressed and released during recording.
The time gap between index marks on the tape should be greater than 1 minute for SP recording and 2 minutes for LP recording.
Use the remote control for this procedure.
1 Press the INDEX SEARCH Button
2 Press the B, C or INDEX SEARCH Button
(j)
repeatedly until the number of pro-
grammes that you want to skip appears.
3 Press the h or g Button.
The DVD/VCR begins rewinding or fast forwarding to the beginning of desired programme.
When the preset programme is reached, the DVD/VCR will start playback automatically.
Notes
Index Search can be set up to 20.
This function will not operate in the Recording
mode.
Operations must be followed up within 30 seconds, from steps 2 to 3. Otherwise the Index Search mode will be cancelled.
To exit the Index Search mode, press the MENU Button in step 2. Or press the C Button after step 3.
(j)
.
–30–
EN
2C15
[Source (Playing) VCR <Monaural>]
(another VCR)
[TV set]
(Use for monitoring)
AERIAL
RF OUT
R
L
COAXIAL OPTICAL
S-VIDEO
OUT
DVD
ANALOG AUDIO OUT
DIGITAL
AUDIO OUT
AV1 (TV)
AV2 (DECODER)
DVD/VCRVCR
to 21-Pin Scart Jack
to RF OUT
to aerial
socket
AV2 (DECODER)
COPYING A VIDEO TAPE
VCR
You can make copies of videotapes made by friends or relatives for your own enjoyment.
WARNING: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.
Connect the recording DVD/VCR (this unit), playing VCR (another VCR) and your TV as outline in the following diagram.
1 Insert a pre-recorded video cassette into
the playing VCR.
2 Insert a blank video cassette, or one you
want to record over, into the cassette com­partment of the recording DVD/VCR.
3 Press the SPEED Button on the remote
control to select the desired recording speed (SP/LP).
4 Select AV2position on the recording
DVD/VCR. See “Other Connections” on page 17.
5 Press the REC Button on the recording
DVD/VCR.
6 Begin playback of the tape in the playback
VCR.
English
Notes
For best results during dubbing, use the DVD/VCRs front panel controls whenever possible. The remote con­trol might affect the playback DVD/VCR's operation.
Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are not recom­mended.
If video or colour fades in and out, you may be copying a copy guarded video tape.
TO MONITOR THE RECORDING
Turn on the TV and select the video channel on the TV.
–31–
EN
2C15
Ta b
TYPE OF TAPE RECORDING/PLAYBACK TIME
TAPE SPEED
SP MODE LP MODE E-60 1 HOUR 2 HOURS E-120 2 HOURS 4 HOURS E-180 3 HOURS 6 HOURS E-240 4 HOURS 8 HOURS
A STATUS DISPLAY
SP
0:12:34
SP
17:40
P02
<CLOCK and CHANNEL
NUMBER mode>
<COUNTER mode>
Press once. Press once.
Press once.
<OFF mode>
VCR
To check the Counter, or Clock & Channel number, press the DISPLAY Button. Each time you press the
DISPLAY Button, TV screen will change as illustrated: When you select the channel using the remote control number buttons, select the desired channel (position number).
VIDEO CASSETTE TAPE
VCR
This DVD/VCR will operate with any cassette that bears the VHS mark. For best results, we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.
You can prevent accidental erasing of a recording by break­ing off the erase prevention tab on the back edge of the cassette.
If you decide to record on the tape again, cover the hole with plastic tape.
TWO DIFFERENT TAPE SPEEDS
Before recording, select the tape speed : SP mode (Standard Play) or LP mode (Long Play). The table below shows the maximum recording/play­back time using E-60, E-120, E-180 or E-240 tapes in each mode.
TV COLOUR SYSTEM
VCR
Different countries use different television colour sys­tems. Tapes recorded in the PAL or NTSC system can be played back on this unit. Usually, the picture on the TV screen will be in black and white when you play back a tape that is recorded in a different colour sys­tem.
Tapes recorded in the NTSC system can be played back on this unit and a PAL system TV set. This fea­ture is only available in the SP mode. When playing back such tapes, the picture may roll up or down, shrink vertically and black bars may appear both at the top and bottom of the screen. Adjust the vertical hold control on your TV, if the TV features this con­trol.
–32–
EN
2C15
PLAYING A DISC
PLAYING A DVD VIDEO OR AN
AUDIO CD
CDDVD
Getting started
Turn on the power of the TV, amplifier and any other components which are connected to the DVD/VCR. (Change the input system to suit the DVD/VCR, and check that the sound volume is correct.)
1 Press the (Standby/Power ON) Button.
¡The power will turn on.
Check that the DVD OUTPUT Light is lit. If not press the DVD Button on the remote control to switch to DVD mode.
2 Press the OPEN/CLOSE (A) Button.
¡The disc loading tray will open.
3 Place a disc into the tray.
¡Make sure the disc is sitting properly in the correct
recess, with the label side up.
Notes
¡While the setup menu is shown you can not open or
close the tray.
¡A prohibited icon may appear
at the top-right on the TV screen during operation, warning that a prohibited operation has been encountered by the DVD/VCR or the disc.
¡If a disc is dirty or has scratches, the pictures may
appear distorted and the playback operation may stop. In such cases, clean the disc and unplug the power cord and then plug it again before resuming playback.
¡With DVDs that use some titles for playback
programme signals, playback may start from the second title, or it may skip these titles.
¡During the playback of two layered disc, pictures
may stop for a moment. This happens when the 1st layer switches to the 2nd layer. This is not a mal­function.
¡When DVD sits idle for more than thirty-five min-
utes, it will be turned off automatically.
USING THE DVD MENUS
English
4 Press the B Button.
¡The tray will close automatically, and playback will
then start from the first chapter or the first track of the disc. With some discs, if the tray has been closed by pressing the OPEN/CLOSE (A) Button, You need to press the B Button to start the disc.
¡When you playback the DVD which a title menu is
recorded, it may appear on the screen. In this case, refer to USING THE DVD MENUS or USING THE TITLE MENU”.
5 Press the C Button to stop play.
DVD
Some DVDs contain their own menus, such as a guid­ance menu which describes the contents of the disc or a selection menu for sound, language and other cus­tomised settings.
1 Press the MENU Button.
¡The DVD menu will appear.
2 Select the desired title.
¡Press the Arrow Buttons (L/K/B/s) to change the
setting, and then press the ENTER Button.
3 Playback will start from the selected title.
–33–
EN
2C15
USING THE TITLE MENU
B
B
B
DVD
RESUMING PLAYBACK FROM
THE POINT WHERE
PLAYBACK STOPPED
With a DVD containing a title menu, you can select desired titles from the menu.
1 Press the TOP MENU Button.
¡The title menu will appear.
¡With some discs, a title menu may appear automati-
cally. In this case, skip to step 2.
2 Select the desired title.
¡Press the Arrow Buttons (L/K/B/s) to select a
desired title. And then press the ENTER Button.
CALLING UP A MENU SCREEN DURING PLAYBACK
For DVDs
¡Press the MENU Button to call up the DVD menu.
¡Press the TOP MENU Button to call up the title
menu.
Note
¡Contents of menus and corresponding menu
operations may vary between discs. Refer to the manual accompanying the disc for details.
CDDVD
1 Press the C Button during playback.
¡Playback will stop, and then appear the resuming
message at the center.
Press 'PLAY' to play from here. To play the beginning, press 'STOP' first and then 'PLAY'.
2 Press the B Button. Playback will start from
the point where the previous playback ses­sion was stopped.
Note
¡The resume function can be reset by pressing the C
Button twice or by opening the disc loading tray.
PAUSING PLAYBACK OR
DISPLAYING A STILL PICTURE
MP3CDDVD
1 Press the F Button during playback.
¡Playback will pause, with sound muted.
2 Press the B Button to resume playback.
STEPPING THROUGH FRAMES
1 Press the F Button while playback is
paused.
¡The next picture frame is dis-
F
played with sound muted each time the Button is pressed.
2 Press the B Button to resume playback.
–34–
DVD
F
EN
2C15
FAST FORWARD/REVERSE
x2
x8
x30
x60
FR SEARCH FF SEARCH
Button Button
TR: __/ 14
×1/16
×1/8
×1/2
Button
STARTING FROM A DESIRED TRACK
CDDVD
1 Press the g or h Button during play-
back.
¡For DVDs pressing the g or h Button cycles
the playback speed in four steps. In case of DVDs, the sound will mute.
¡For audio CDs, the playback speed is ×16 fixed.
2 Press the B Button to return to normal play-
back speed.
¡FAST FORWARD or REVERSE from a TITLE to
other TITLEs is not possible.
¡With some discs, the audio may take a while to be
played back after a SEARCH.
CD
There are 2 ways you can jump to a desired track.
By using only the Number Buttons.
1 Directly enter the desired track number with
the Number Buttons when the disc is being played, stopped, or paused.
By using the SEARCH MODE Button.
1 Press the SEARCH
MODE Button.
¡
Track search display will show up.
2 Enter the desired track number with the
Number Buttons (If you are entering a single digit number press “0” first).
¡In either way, when you finish entering the number,
the selected track will start automatically.
Notes
¡If you didn’t press 0 before entering the single
digit number, you have to press the ENTER Button to go to the desired track.
English
¡Slow motion mode will be activated. ¡Pressing the g Button cycles the playback speed
Notes
¡Slow playback is not available with audio CDs. ¡Reverse slow motion is not available. ¡Slow playback from a TITLE to other TITLE is not
SLOW MOTION
DVD
1 Press the g Button while playback is
paused. (Sound remains muted.)
in three steps. Select the appropriate speed while referring to the speed indication on the screen.
2 Press the B Button to return to normal play-
back speed.
possible.
STARTING FROM A DESIRED
TITLE OR CHAPTER
There are 2 ways you can jump to a desired title or a chapter.
By using the SEARCH MODE Button.
1 Press the SEARCH MODE
Button.
¡
Title/Chapter search display will show up.
2 Press the Number Buttons to enter a desired
title or chapter number.
3 Enter the desired title or chapter number
with the Number Buttons (If you are entering a single digit number press “0” first).
¡When you finish entering the number, the selected
title or chapter will start automatically
Notes
¡If you didn’t press 0 before entering the single
digit number, you have to press ENTER to go to the desired title or the chapter.
By using only the Number Buttons.
TITLE SEARCH:
1
Directly enter the desired title number with the Number Buttons when the disc is stopped.
–35–
TT: 1/ 12 CH: __ / 3
.
DVD
EN
2C15
CHAPTER SEARCH:
1 Directly enter the desired chapter number
with the Number Buttons when the disc is being played or paused.
¡When you finish entering the number, the selected
title or chapter will start automatically.
DVDCD
TRICKS WITH THE SKIP BUTTONS (H/G )
If the SKIP Button G is pressed during playback or while playback is paused, the current track/chapter will be skipped and the next track/chapter will start. When the SKIP Button H is pressed once, the top of the current track/chapter will be located for replaying. When the SKIP Button H is pressed again within 2-seconds after play­back begins, the previous track/chapter will be located.
Call back the marker
¡Using the Arrow Buttons (s/ B), position the cur-
sor on to the marker number to be called back and press the ENTER Button.
Clear the marker
¡Using the Arrow Buttons (s/ B), position the cur-
sor on to the marker number to be cleared and press
the C. RESET Button. To all markers, place the cursor on AC (All clear markers) and press the ENTER Button.
2 Press the SEARCH MODE Button or the
RETURN Button to exit the display.
RANDOM (Audio CD)
STARTING FROM A DESIRED
TIME COUNT
CDDVD
1 Press the SEARCH MODE Button twice.
2 Press the Number Buttons to set the
desired time count.
¡Example: 1 hour, 23 minutes
and 30 seconds
1 2 3 3 0
Notes
¡In the case of DVD, Time Search in Title is effec-
tive. (But Time Search in Chapter is ineffective.)
¡In the case of CD, Time Search in Track is effective.
(But Time Search in the entire disc is ineffective.)
¡Playback from a desired time count is not available
with some discs or if the unit is in stop mode.
¡If wrong numbers are entered, press the CLEAR/
C. RESET Button and re-enter the correct numbers.
TIME 1:23:30 TOTAL 1:29:00
MARKER
CDDVD
You can define the part to be called back.
1 Press the SEARCH MODE Button three
times during playback.
Set the marker
¡Using the Arrow Buttons (s/ B), position the cur-
sor on to the marker number shown as NOT SET. Press the ENTER Button when the screen to be reviewed appears. The marked time will be displayed. Up to 5 points can be marked.
1 2 3 4 5 AC
NOT SET
CD
1 Press the MODE Button in stop mode.
¡The programme setting menu screen will appear.
2 Press the MODE Button
again.
RANDOM
EXIT : MODESTART : PLAY
3 Press the B Button.
Random playback will then start.
Note
¡Programme playback is not available during random play-
back.
REPEAT
CDDVD
1 Press the REPEAT Button during playback.
For DVDs
¡A single title or chapter is played back repeatedly.
¡Pressing the REPEAT Button cycles the display on
the screen as follows.
REPEAT [OFF]
No repeat playback.
For audio CDs
¡The whole disc or a single track is played back
repeatedly.
¡Pressing the REPEAT Button cycles the display on
the screen through Off, Track and All.
REPEAT
[CHAPTER]
The current Chapter is
played back repeatedly.
REPEAT
[TITLE]
The current Title is
played back repeatedly.
–36–
EN
2C15
The whole Disc is played back repeatedly.
REPEAT [ALL]
REPEAT [TRACK]
The current Track is played back repeatedly.
No repeat playback.
REPEAT [OFF]
If the REPEAT Button is pressed once dur-
REPEAT [ A - ]
REPEAT [ A - B ]
REPEAT
[ OFF ]
02 05 07 04 10 14 06 15 21 08 20 28 10 25 35 12 30 42 11 34 49 16 40 58 18 45 63 01 03 _ _
PROGRAM TIME 2:07:43 1/1
RANDOM
: MODE
EXIT
: RETURN
START: PLAY
DELETE
: CLEAR
ing program/random playback, the current track is played back repeatedly.
If the REPEAT Button is pressed again, the program/random playback is performed repeatedly.
Notes
¡With DVDs, the A-B repeat section can be set only
within the current title.
¡With audio CDs, the A-B repeat section can be set
within the current track.
¡A-B repeat is not available with some scenes in
DVD.
¡To cancel the A point which was set, press the
CLEAR/C. RESET Button.
¡A-B repeat playback does not function when title,
chapter, or repeat (all) playback has been set.
PROGRAMME(Audio CD)
English
Notes
¡Repeat playback is not available with some discs. ¡The REPEAT setting will be cleared when moving
to other title, chapter or track.
¡Repeat playback is not function during A-B repeat
playback.
A-B REPEAT
You can define a section to be played back repeatedly.
1
Press the A-B REPEAT Button during playback.
¡The starting point (A) will then
be selected.
2 Press the A-B REPEAT Button again at the
end point (B) of the desired section.
¡The selected section will be
played back repeatedly.
3 To exit A-B repeat playback, press the A-B
REPEAT Button and set it to OFF.
CD
1
Press the MODE Button in stop mode.
¡The programme screen will
appear.
PROGRAM TIME 0:00:00 1/1
--
START: PLAY RANDOM
: MODE
DELETE EXIT
: CLEAR
: RETURN
CDDVD
2 Press the Number Buttons to enter the
desired track numbers.
¡50 programmes can be dis-
played at once on the screen. Press L to go to the next page.
3 Press the B Button.
¡Playback will start in the programmed order.
¡While the programme is being played back, C works
as follows.
¡Press the C Button once and then the B
Button again, playback will restart from the point where the C Button was pressed. (Programme continued)
¡Programme will be cleared when you turn the
power off.
TO CLEAR THE PROGRAMME
¡Press the C Button twice, and the programme will
be cleared.
–37–
EN
2C15
Notes
¡Adding programs is not possible during programme
playback. You must stop the current playback before such operations can be carried out.
¡Press the CLEAR/C. RESET Button to cancel a pro-
gram. The most recently entered programme will then be deleted.
¡Up to 99 programs can be entered.
¡Playback from a desired track and random playback
are not available during programme playback.
¡programme settings are cleared when the power is
turned off or the disc loading tray is opened.
¡Press the MODE Button to check the programmed
setting.
ZOOM PLAYBACK
(enlargement on-screen)
DVD
Images can be enlarged on the screen to your taste.
1 Press the ZOOM Button during playback.
¡An image will be enlarged at the center of the
screen.
¡Pressing the ZOOM Button cycles the zooming
images in two steps.
ZOOM [x4]ZOOM [x2] ZOOM [OFF]
2 When the Arrow Buttons (K/L/ s / B) is
pressed during zoom play, the part to be zoomed moves.
¡The zooming frame can be moved from the center
.... 4 steps to the right. 4 steps to the left. 4 steps to
the top. 4 steps to the bottom when 2 time zooming, and 6 steps each when 4 time zooming.
¡Current position will be displayed on the right-bot-
tom of the screen. Press the ENTER Button, and the display disappears.
Note
¡Zooming function does not work while disc menu is
shown.
PLAYING AN MP3 DISC
MP3
1
Insert an MP3 file-recorded disc.
¡The MP3 menu screen shows up.
¡+ appears at the head of the
album name.
¡The player can recognise 255
ALBUMS and TRACKS altogether.
¡If all the TRACKS cannot be displayed at once on
the screen, L appears to go to the next page. If
there is a previous page, K” appears on-screen. On
the left of L, the current page and the total num-
ber of pages are displayed.
2 Press the B Button after the following oper-
ation.
[FIRST PLAY]
Select FIRST PLAY with the Arrow Buttons (K/L).
[TRACK]
Select the desired TRACK with the Arrow Buttons (K/L).
[ALBUM]
Select the desired ALBUM with the Arrow Buttons (K/L), and call the TRACKs with ENTER Button.
¡Press the ENTER or the Arrow Button (B) to go to
the next hierarchy.
¡Press the Arrow Button (s) to go back to the previ-
ous hierarchy.
¡Press the TOP MENU Button to go back to the top
hierarchy.
¡ALBUMS can be played up to the 8th hierarchy.
3 To stop the play, press the C Button.
ALBUM NAME
FIRST PLAY
+ALBUM01 +ALBUM02 +ALBUM03 +ALBUM04
SELECT:
RETURN:
/ENTER:
START: PLAY
1/15
–38–
EN
2C15
CHANGING THE ON-SCREEN
+ALBUM01
TRACK11
TRACK12 TRACK13 TRACK14
ALBUM NAME
RETURN:
1/15
START: PLAY
SELECT:
/ENTER:
RANDOM: MODE
EXIT
: RETURN
START
: PLAY DELETE: CLEAR
+ALBUM01
+ALBUM02 +ALBUM03 TRACK01 TRACK02
PROGRAM - ALBUM NAME
1/11
1/1
RANDOM: MODE
EXIT
: RETURN
START
: PLAY DELETE: CLEAR
+ALBUM11 +ALBUM12
TRACK11
TRACK12 TRACK13
PROGRAM - ALBUM01
1/11
1/1
TRACK11
0:02:31 A
TRACK11
TRACK12 TRACK13 TRACK14 TRACK15
DISPLAY DURING MP3 DISC PLAY
MP3
The information on an MP3 disc in play can be checked.
1
Press the DISPLAY Button during playback.
¡The TRACK currently in play
will be highlighted.
ALBUM NAME A
TRACK11
TRACK12 TRACK13 TRACK14 TRACK15
2 Press the DISPLAY Button again.
¡The album name being dis-
played will be replaced by the elapsed time of the track.
¡
will be displayed when the repeat play has been selected.
T : Track repeat
A : Album (folder) repeat
D : Disc repeat
3 Press the DISPLAY Button again, and the
display screen disappears.
PLAYING AN MP3 DISC FROM A
DESIRED TRACK
MP3
1 Press the SEARCH MODE Button during
playback.
¡The SEARCH menu shows up. ¡The TRACK currently in play or under RESUME
ON will be highlighted. In the case of RESUME OFF, the first track of the disc will be highlighted.
¡Press the RETURN Button, and the SEARCH menu
disappears.
Notes
¡During play, a desired track can be directly searched.
Just type in the TRACK number with the Number
Buttons.
¡If the typed TRACK number is not available, the
disable symbol appears and the direct search mode
is cancelled.
¡Playback cannot be started from a desired time
count.
PLAYING AN MP3 DISC AT
RANDOM
MP3
1
Press the MODE Button twice in STOP mode.
¡The programme setting menu screen will appear.
RANDOM
START
: PLAY
EXIT
: MODE
2 Press the B Button.
¡Random play starts.
PLAYING AN MP3 DISC IN A
PROGRAMMED WAY
MP3
1
Press the MODE Button in STOP mode.
¡The programme screen shows up.
English
2 Using the Arrow Buttons (K/L), select a
track to be played. Then press the to start playing.
B Button
2 Use the Arrow Buttons (K/L) to select a
track. Then press the ENTER Button to save it in a program.
¡When an ALBUM name
is highlighted, press the
L Button, and the next
hierarchy shows up.
–39–
EN
2C15
¡Press the Arrow Button (K) to go back to the upper
Both right and left channels are active (stereo).
Only the left channel is active.
AUDIO STEREO
AUDIO L-CH
AUDIO R-CH
Only the right channel is active.
hierarchy.
¡If the entire programme cannot be displayed at once
on the screen, L appears to go to the next page.
3 When the disc has been programmed, press
the
B Button.
¡Programmed play starts.
SETTINGS
Notes
¡Press the CLEAR/C. RESET Button, and the last-
programmed entry will be deleted.
¡Press the RETURN Button, and the STOP screen
will show up with the programme contents in mem-
ory.
¡The programme setting will be cancelled when the
power is turned off or the disc tray is opened.
¡programme will be cleared when you turn the
power off.
TO CLEAR THE PROGRAM
¡Press the C Button twice, and the programme will
be cleared.
CHANGING THE AUDIO
LANGUAGE OR SOUND MODE
CD DVD
The DVD/VCR has a function which allows you to select the desired audio language and sound mode.
For DVDs
Press the AUDIO Button during playback, and then press the AUDIO Button to select the desired audio language.
¡The audio language can be changed if multiple
languages are recorded on the DVD being played.
AUDIO 1.ENG DolbyD 5.1CH
AUDIO 2.FRE DolbyD 5.1CH
AUDIO 3.JPN DolbyD 5.1CH
HELLO
Note
¡For some Audio language, three dashes (---) may
appear instead of a three-letter abbreviation for the language (ENG, FRE, etc.).
Bon jour
–40–
For audio CDs
Press the AUDIO Button during playback.
¡Pressing the AUDIO Button cycles the sound mode
through STEREO, L-CH and R-CH.
Notes
¡Pressing the AUDIO Button may not work on some
DVDs with multiple audio languages (e.g. DVDs
which allow audio language setting on the disc
menu). Operation varies between discs, so refer to
the manual accompanying the disc.
¡Current audio language and sound mode will be dis-
played when you press the AUDIO Button at first.
¡If a desired language is not shown after pressing the
AUDIO Button several times, the disc does not have
an audio source in that language.
¡The audio language resets to the one which has been
selected in the setup mode, every time the power is
turned on or discs are replaced. If that language is
not available on a disc, a language defined by the
disc is selected.
¡The screen display will disappear after about 5
seconds.
EN
2C15
CHANGING THE SUBTITLE
LANGUAGE
DVD
The DVD/VCR has a function which allows you to select the desired language for subtitles.
1 Press the SUBTITLE Button during playback,
and then press the SUBTITLE Button to select the desired subtitle language.
¡The subtitle language can be changed if the subtitles
are recorded in multiple languages on the DVD being played.
¡The subtitle language cannot be changed if the
subtitles are recorded in a single language on the DVD being played.
SUBTITLE 1.ENG/6
Subtitle 1
SUBTITLE 2.FRE/6
SUBTITLE OFF
¡Pressing the SUBTITLE Button cycles the subtitle
language from SUBTITLE 1, SUBTITLE 2 and all the languages recorded.
¡Current subtitle mode will be displayed when you
press the SUBTITLE Button at first.
¡Press the SUBTITLE Button, and then press the
Arrow Buttons (s / B) to set it to on or off.
Subtitle 2
OFF
¡The subtitle language resets to the one which has
been selected in the setup mode, every time the
power is turned on or discs are replaced. If that
language is not available on a disc, a language
defined by the disc is selected.
¡It may take time to display the subtitles in the
selected language.
¡The screen display will disappear after about 5
seconds.
¡When SUBTITLE NOT AVAILABLE appears on-
screen, it means no subtitle is recorded on the scene.
CHANGING THE CAMERA
ANGLE (Multi-Angle Pictures)
DVD
The DVD/VCR has a function which allows you to select the desired camera angle.
1
Press the ANGLE Button during playback.
¡If the disc contains sequences recorded from differ-
ent camera angles, the angle icon ( ) will appear
at the top-right of the screen. You can change the
camera angle when the icon appears on the screen.
¡The camera angle cannot be changed if the disc does
not contain sequences recorded from different
camera angles.
2
Press the ANGLE Button while the angle number is shown on the screen.
ANGLE 1 / 8
Angle 1
English
HELLO
Bon jour
Notes
¡For some Audio language, three dashes (---) may
appear instead of a three-letter abbreviation for the language (ENG, FRE, etc.).
¡Some discs allow subtitle language setting on the
disc menu. (Operation varies between discs, so refer to the manual accompanying the disc.)
¡If the desired language is not shown after pressing
the SUBTITLE Button several times, the disc does not have subtitles in that language.
ANGLE 2 / 8
ANGLE 8 / 8
Angle 2
Angle 8
Notes
¡The screen display will disappear after about 5
seconds.
¡Current camera angle will be displayed when you
press the ANGLE Button at first.
–41–
EN
2C15
CHANGING THE ON-SCREEN
TT 1/2 0:00:00 -1:23:45
TT(Title): Current title number / the number of total titles.
TIME: Elapsed time of the current title on remaining time of the current title.
CH 7/49 0:01:46 -0:03:27
CH(Chapter): Current chapter number / the number of total chapter.
TIME: Elapsed time of the current chapter and remaining time of the current chapter.
BLACK LEVEL : ON
BIT RATE
BIT RATE indicator will appear. BIT RATE shows the quantity of information which is recorded in DVD.
C
L0
Layer number (*1) L0: Layer 0 is playing back L1: Layer 1 is playing back Current Repeat setting (*2) C: Chapter repeat T: Title repeat A B: A-B repeat
ALL 4/12 0:13:45 -0:45:40
ALL: Current track number / the number of total tracks.
TIME: Elapsed time of the current disk and remaining time of the current disc.
TR 4/12 0:03:21 -0:02:15
TR(Track): Current track number / the number of total tracks.
TIME: Elapsed time of the current track and remaining time of the current track.
DISPLAY
¡Use the Number Button to start from a desired track.
3 Press the
DISPLAY
Button
to exit the display.
CDDVD
You can check the information about the disc by pressing the DISPLAY Button on the remote control.
For DVDs
1
Press the DISPLAY Button during playback.
2
Press the DISPLAY Button again.
¡
Use the Number Button to start from a desired chapter.
3 Press the
DISPLAY
Button again.
BLACK LEVEL SETTINGS
DVD
You can select the BLACK LEVEL ON to make the black areas of the picture brighter.
1
Press the MODE Button during playback.
¡The setup screen will appear.
2
Press the ENTER Button to set it on or off.
¡ON : It makes the dark parts brighter.(Default : ON)
OFF : Original picture which is recorded on the disc
will be shown.
¡Press the RETURN Button to exit the display.
TRUSURROUND SETTINGS
DVD
You can enjoy stereophonic sound system when you playback Dolby Digital and PCM 48kHz sound.
*1) It appears when the layered disc is playing back *2) It appears when Repeat play back is set.
4 Press the
For audio CDs
1
2
DISPLAY
Button
or the RETURN
Button to exit the display.
Press the DISPLAY Button during playback.
Press the DISPLAY Button again.
1
Press the SURROUND Button during playback.
or
1 Press the MODE Button twice.
¡The setup screen will appear.
2
Press the SURROUND Button to turn it on or off.
or
SRS TruSurround ON
2 Press the ENTER Button.
ON : SRS TruSurround on
OFF : SRS TruSurround off (Default : OFF)
¡Press the RETURN Button to exit the display.
¡
SRS TruSurround is available only when the
DVD/VCR is connected to a TV or stereo using the
red and white AUDIO OUT jacks on the DVD/VCR.
–42–
EN
2C15
CHANGING THE SETUP ITEMS
1.
LANGUAGE OPTIONS
2.
DISPLAY OPTIONS
3.
AUDIO OPTIONS
4.
PARENTAL
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
Please enter a 4-digit Language code.
- - - -
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
LANGUAGE OPTIONS
AUDIO LANGUAGE
LANGUAGE CODE
1.
LANGUAGE OPTIONS
2.
DISPLAY OPTIONS
3.
AUDIO OPTIONS
4.
PARENTAL
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
1.
AUDIO ORIGINAL
2.
SUBTITLE OFF
3.
DISC MENU ORIGNAL
4.
PLAYER MEMU ENGLISH
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
LANGUAGE OPTIONS
1.
AUDIO ORIGINAL
2.
SUBTITLE OFF
3.
DISC MENU ORIGNAL
4.
PLAYER MEMU ENGLISH
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
LANGUAGE OPTIONS
1.
AUDIO ORIGINAL
2.
SUBTITLE OFF
3.
DISC MENU ORIGNAL
4.
PLAYER MEMU ENGLISH
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
LANGUAGE OPTIONS
1.
AUDIO ORIGINAL
2.
SUBTITLE OFF
3.
DISC MENU ORIGNAL
4.
PLAYER MENU ENGLISH
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
LANGUAGE OPTIONS
LANGUAGE SETTINGS
1
Press the SETUP Button
¡The setup screen will appear.
2 Press the Arrow Buttons (K/L) to select
Language, and then press the ENTER Button.
3 Press the Arrow Buttons (K/L) to select an
item, and then press the ENTER Button.
in STOP mode
DVD
.
DISC MENU: (The disc menu appears in selected language.)
PLAYER MENU: (The on-screen display appears in selected lan­guage.)
4
Press the Arrow Buttons (
K/L
) to select a desired item, and then press the ENTER Button.
¡If OTHER is selected on the AUDIO LAN-
GUAGE” “SUBTITLE LANGUAGE or DISC MENU LANGUAGE setting screen, the Language Code setting screen will appear. Press the Number Buttons to enter the desired language code while referring to the list on page 47.
English
AUDIO: (Voice is played back in selected language.)
SUBTITLE: (Subtitles are shown in selected language.)
5 Press the SETUP Button.
¡The setup mode will be cancelled and the ordinary
screen will appear.
Notes
¡Language Setting for Audio and Subtitle is not avail-
able with some discs. Then use the Audio and Subtitle Button. Details are on pages 40 and 41.
¡You can also select the item by pressing the numbers
which are displayed with the item.
¡When you change the setup items, press the C
Button if you are in playback mode.
¡While the setup menu is shown you can not open or
close the tray.
–43–
EN
2C15
DISPLAY SETTINGS
1.
LANGUAGE OPTIONS
2.
DISPLAY OPTIONS
3.
AUDIO OPTIONS
4.
PARENTAL
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
1.
LANGUAGE OPTIONS
2.
DISPLAY OPTIONS
3.
AUDIO OPTIONS
4.
PARENTAL
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
1.
TV ASPECT 4:3 L-BOX
2.
FRONT DISPLAY BRIGHT
3.
ANGLE MARK OFF
4.
AUTO POWER OFF ON
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
DISPLAY OPTIONS
1.
TV ASPECT 4:3 L-BOX
2.
FRONT DISPLAY BRIGHT
3.
ANGLE MARK ON
4.
AUTO POWER OFF ON
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
DISPLAY OPTIONS
1.
TV ASPECT 4:3 L-BOX
2.
FRONT DISPLAY BRIGHT
3.
ANGLE MARK ON
4.
AUTO POWER OFF ON
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
DISPLAY OPTIONS
1.BRIGHT
2.DIM
3.AUTO DIM
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
DISPLAY OPTIONS
FRONT DISPLAY
1.
TV ASPECT 4:3 L-BOX
2.
FRONT DISPLAY BRIGHT
3.
ANGLE MARK ON
4.
AUTO POWER OFF ON
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
DISPLAY OPTIONS
1.4:3
LETTER BOX
2.4:3
PAN-SCAN
3.16:9
WIDE
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
DISPLAY OPTIONS
TV ASPECT
1
Press the SETUP Button in STOP mode.
¡The setup screen will appear.
2 Press the Arrow Buttons (K/L) to select
DISPLAY and then press the ENTER Button.
DVD
FRONT DISPLAY (Default : BRIGHT) Adjust the brightness of the display of the unit. AUTO DIM: Stays dim only during playback.
ANGLE MARK (Default : ON) Display or not display the Angle icon on the screen.
3 Press the Arrow Buttons (K/L) to select an
item, and then press the ENTER Button.
TV ASPECT
(Default : 4:3 LETTER BOX) 4:3 L-BOX: Wide screen with black bars on top and bottom 4:3 PAN-SCAN : Full height picture, trimmed both sides 16:9 WIDE : If wide screen TV is connected
AUTO POWER OFF
(Default : ON) Set or not set to turn off after the screen saver is started and no keys are pressed for 30 minutes.
4
Press the Arrow Buttons (
K/L
) to select a desired item, and then press the ENTER Button.
5 Press the SETUP Button.
¡The setup mode will be cancelled and the ordinary
screen will appear.
Notes
¡Be sure to press the SETUP Button, or the setting
will not work.
¡You can also choose the item by pressing the
Number Buttons.
¡While the setup menu is shown you can not open or
close the tray.
–44–
EN
2C15
AUDIO SETTINGS
1.
DRC OFF
2.
DOLBY DIGITAL BITSTREAM
3.
DTS OFF
4.
MPEG PCM
5.
DOWN SAMPLING AUTO
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
AUDIO OPTIONS
1.
DRC OFF
2.
DOLBY DIGITAL BITSTREAM
3.
DTS OFF
4.
MPEG PCM
5.
DOWN SAMPLING AUTO
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
AUDIO OPTIONS
SETUP MENU
AUDIO OPTIONS
1.DRC
OFF
2.
DOLBY DIGITAL BITSTREAM
3.
DTS OFF
4.
MPEG PCM
5.
DOWN SAMPLING AUTO
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
1.
DRC OFF
2.
DOLBY DIGITAL BITSTREAM
3.
DTS OFF
4.
MPEG PCM
5.
DOWN SAMPLING AUTO
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
AUDIO OPTIONS
SETUP MENU
AUDIO OPTIONS
DOWN SAMPLING
1.
AUTO
2.
48kHz
3.
96kHz
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
1.
LANGUAGE OPTIONS
2.
DISPLAY OPTIONS
3.
AUDIO OPTIONS
4.
PARENTAL
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
1.
LANGUAGE OPTIONS
2.
DISPLAY OPTIONS
3.
AUDIO OPTIONS
4.
PARENTAL
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
1.
DRC OFF
2.
DOLBY DIGITAL BITSTREAM
3.
DTS OFF
4.
MPEG PCM
5.
DOWN SAMPLING AUTO
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
AUDIO OPTIONS
1
Press the SETUP Button in STOP mode.
¡The setup screen will
appear.
2 Press the Arrow Buttons (K/L) to select
Audio and then press the ENTER Button.
DVD
DTS (Default : OFF) BITSTREAM : Output DTS sound Set to BITSTREAM when the unit is connected to DTS Decoder. (Effective for DVD only. DTS CD output readily available without switching over.)
English
MPEG (Default : PCM) BITSTREAM : Output MPEG sound Set to BITSTREAM when the unit is connected to MPEG Decoder. To turn off MPEG, set at PCM.
3 Press the Arrow Buttons (K/L) to select an
item, and then press the ENTER Button.
DRC (Default : OFF)
On : DRC
(Dynamic Range Control)
¡This function is for controlling the range of sound
volume. By compressing the range of sound volume, it is possible not only to suppress the output of loud sound at night and but also to raise the volume of low sound.
¡This function is effective only for the sound record-
ed by Dolby Digital recording.
Dolby Digital (default : BITSTREAM) BITSTREAM : Output by Dolby Digital Set to BITSTREAM when the unit is connected to Dolby Digital Decoder. To turn off Dolby Digital, set at PCM.
DOWN SAMPLING (Default : AUTO) Set the output for the DVD
recorded in PCM 96kHz (96kHz or 48kHz, or AUTO)
¡Press the Arrow Buttons (K/L) to select an item,
and then press the ENTER Button.
When playing a disc with copyright protection
¡If you select 96kHz, copyright protection will be
activated and no sound will come out. If you select AUTO, sound will be down sampled at 48kHz.
4
Press the SETUP Button.
¡The setup mode will be cancelled and the ordinary
screen will appear.
Note
¡While the setup menu is shown you can not open or
close the tray.
–45–
EN
2C15
PARENTAL LOCK
1.
LANGUAGE OPTIONS
2.
DISPLAY OPTIONS
3.
AUDIO OPTIONS
4.
PARENTAL
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
1.
RATING LEVEL ALL
2.
CHANGE
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
PARENTAL CONTROL
ALL
LEVEL 8 ADULT LEVEL 7 LEVEL 6 LEVEL 5
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
PARENTAL CONTROL
RATING LEVEL
1.
LANGUAGE OPTIONS
2.
DISPLAY OPTIONS
3.
AUDIO OPTIONS
4.
PARENTAL
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
SELECT:
/ SET
: ENTER
Enter password.
- - - -
SETUP MENU
EXIT
: SETUP
CANCEL
: RETURN
PARENTAL CONTROL
CREATE PASSWORD
1
Press the SETUP Button in STOP mode.
¡The setup screen will appear.
2 Press the Arrow Buttons (K/L) to select
PARENTAL, and then press the ENTER Button.
3 Press the Number Buttons to enter a 4-digit
password (you can use any 4-digits except for 4737), and then press the ENTER Button.
¡This number will be used as the password from the
second time onward.
¡By entering the password, you can then change the
control level and password settings.
¡If you want to change the password, select
CHANGE and enter a new password. Then press the ENTER Button.
4
Press the Arrow Buttons ( item, and then press the ENTER Button.
K/L
) to select an
DVD
When Parental Level is selected
¡Press the Arrow Buttons (K/L)
to select an item from ALL or 8 to 1, and then press the ENTER Button.
5
Press the SETUP Button.
¡The setup mode will be cancelled and the ordinary
screen will appear.
CONTROL LEVELS
¡
ALL
All parental lock is cancelled.
¡
Level 8 ADULT
DVD software of any grade (adult/general/children) can be played back.
¡
Levels 7 to 2
Only DVD software intended for general use and children can be played back.
¡
Level 1 KIDS SAFE
Only DVD software intended for children can be played back, with those intended for adult and general use prohibited.
Notes
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check if the parental lock function operates in the way that you have set.
¡Record the password in case you forget it.
¡While the setup menu is shown you can not open or
close the tray.
IF YOU FORGET THE PASSWORD
1) Press the 4, 7, 3, 7 at step 3.
¡Password will be cleared and parental level will be
set to ALL.
2) Proceed the above steps 3-5 again.
–46–
EN
2C15
LANGUAGE CODE LIST
No.
1
Afar
2
Abkhazian
3
Afrikaans
4
Amharic
5
Arabic
6
Assamese
7
Aymara
8
Azerbaijani
9
Bashkir
10
Byelorussian
11
Bulgarian
12
Bihari
13
Bislama
14
Bengali;Bangla
15
Tibetan
16
Breton
17
Catalan
18
Corsican
19
Czech
20
Welsh
21
Danish [DAN]
22
German [GER]
23
Bhutani
24
Greek [GRE]
25
English [ENG]
26
Esperanto
27
Spanish [SPA]
28
Estonian
29
Basque
30
Persian
31
Finnish [FIN]
32
Fiji
33
Faroese
34
French [FRE]
35
Frisian
36
Irish [IRI]
37
Scots Gaelic
38
Galician
39
Guarani
40
Gujarati
41
Hausa
42
Hindi
43
Croatian
44
Hungarian [HUN]
45
Armenian
46
Interlingua
47
Interlingue
48
Inupiak
49
Indonesian
50
Icelandic [ICE]
51
Italian [ITA]
52
Hebrew
53
Japanese
54
Yiddish
55
Japanese [JPN]
56
Georgian
57
Kazakh
58
Greenlandic
59
Cambodian
60
Kannada
61
Korean [KOR]
62
Kashmiri
63
Kurdish
64
Kirghiz
65
Latin
66
Lingala
67
Laothian
68
Lithuanian
Language Country code
4747 4748 4752 4759 4764 4765 4771 4772 4847 4851 4853 4854 4855 4860 4861 4864 4947 4961 4965 4971 5047 5051 5072 5158 5160 5161 5165 5166 5167 5247 5255 5256 5261 5264 5271 5347 5350 5358 5360 5367 5447 5455 5464 5467 5471 5547 5551 5557 5560 5565 5566 5569 5647 5655 5669 5747 5757 5758 5759 5760 5761 5765 5767 5771 5847 5860 5861 5866
No.
69
Latvian;Lettish
70
Malagasy
71
Maori
72
Macedonian
73
Malayalam
74
Mongolian
75
Moldavian
76
Marathi
77
Malay
78
Maltese
79
Burmese
80
Nauru
81
Nepali
82
Dutch [DUT]
83
Norwegian [NOR]
84
Occitan
85
(Afan)Oromo
86
Oriya
87
Panjabi
88
Polish
89
Pashto;Pushto
90
Portuguese [POR]
91
Quechua
92
Rhaeto-Romance
93
Kirundi
94
Romanian [RUM]
95
Russian [RUS]
96
Kinyarwanda
97
Sanskrit
98
Sindhi
99
Sangho
100
Serbo-Croatian
101
Singhalese
102
Slovak
103
Slovenian
104
Samoan
105
Shona
106
Somali
107
Albanian
108
Serbian
109
Siswat
110
Sesotho
111
Sundanese
112
Swedish [SWE]
113
Swahili
114
Tamil
115
Telugu
116
Tajik
117
Thai
118
Tigrinya
119
Turkmen
120
Tagalog
121
Setswana
122
Tonga
123
Turkish [TUR]
124
Tsonga
125
Tatar
126
Twi
127
Ukrainian
128
Urdu
129
Uzbek
130
Vietnamese
131
Volapuk
132
Wolof
133
Xhosa
134
Yoruba
135
Chinese [CHI]
136
Zulu
Language Country code
5868 5953 5955 5957 5958 5960 5961 5964 5965 5966 5971 6047 6051 6058 6061 6149 6159 6164 6247 6258 6265 6266 6367 6459 6460 6461 6467 6469 6547 6550 6553 6554 6555 6557 6558 6559 6560 6561 6563 6564 6565 6566 6567 6568 6569 6647 6651 6653 6654 6655 6657 6658 6660 6661 6664 6665 6666 6669 6757 6764 6772 6855 6861 6961 7054 7161 7254 7267
If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Audio or Subtitle language setting on pages 40 and 41. If you choose any other languages, ---will be dis­played instead. (3 letter language code is written in bracket.)
–47–
EN
2C15
English
TROUBLESHOOTING GUIDE
If the DVD/VCR does not perform properly when operated as instructed in this INSTRUCTION MANUAL, check the player consulting the following checklist.
VCRDVD
PROBLEM CORRECTIVE ACTION
No power. Make sure the power plug is connected to an AC outlet.
The player does not respond to the remote control.
VCR
Timer recording is not pos­sible.
Recording mode cannot be engaged.
No picture or poor picture on playback.
No picture but the audio is OK in playback.
Playback picture is partially noisy.
On-the-air TV programmes cannot be seen.
Video or colour fades in and out when making a copy of a video tape.
Mode
PROBLEM
Mode
Make sure the power is turned on.
Check if the power plug is connected to an AC outlet.
Check the batteries in the remote control.
Aim the remote control directly at the remote sensor. If necessary, remove all the obsta-
cles between the sensor and the remote.
You have to be within 23 feet of the DVD/VCR.
Check if the correct mode is selected. If not switch the mode by pressing the DVD or VCR
Button on the remote control.
CORRECTIVE ACTION
Make sure the timer recording is set correctly.
Make sure the power is off.
Make sure the DVD/VCR clock is set correctly.
Make sure
after the tab with adhesive tape.
Set your TV to the video channel.
Fine tune your TV.
Head cleaning is necessary, consult the nearest Authorized Service Center.
Adjust tracking control for a better picture by using the CH Buttons (
Re-check the AERIAL and RF OUT connections.
Set your TV to the TV channel correctly.
You cannot copy a copyrighted video tape.You are experiencing copy guard protection.
the erase-prevention tab on the tape is intact. If removed, cover the hole
o/p).
–48–
EN
2C15
DVD
Mode
Symptom
No picture
Disc cannot be played
No sound
Distorted picture
Audio or subtitle language does not match the setup.
The camera angle cannot be changed.
Audio or subtitle language cannot be changed.
Prohibited icon appears on the screen, prohibiting an operation.
The tray cannot be open or close.
Cause
Loose video connection.
¡
Wrong disc.
¡
No disc.
¡
Dirty disc.
¡
Disc is placed upside down.
¡
Parental lock is active.
¡
Loose audio connection.
¡
The power of the connected
¡
audio component is off. Wrong audio output settings.
¡
Wrong input settings on the
¡
connected audio component. Some discs may not be played
¡
back right away after a SEARCH. Copy protection is active.
¡
Immediately after playing, press
¡
fast forward or in reverse. The 1st layer is switching to the
¡
2nd layer, when playing a two layered disc. The selected language is not
¡
available for audio or subtitles on the DVD.
The DVD does not contain
¡
sequences recorded from different camera angles.
The DVD does not contain
¡
audio source or subtitles in the selected language.
That operation is prohibited by
¡
the player or disc.
The setup menu is displayed.
¡
Remedy
Connect the video cables firmly.
¡
Insert a correct video disc that plays on this player.
¡
Insert a disc.
¡
Clean the disc.
¡
Place the disc correctly, with the label side up.
¡
Cancel the parental lock or change the control level.
¡
Connect the audio cables firmly.
¡
Turn the power of the audio component on.
¡
Correct the audio output settings.
¡
Correct the input settings on the audio
¡
component. No malfunction.
¡
Connect the player directly to the TV.
¡
There are some cases where pictures may be
¡
slightly distorted, which are not a sign of a malfunction. Although Pictures may stop for a moment, this
¡
is not a malfunction. No malfunction.
¡
No malfunction.
¡
No malfunction.
¡
No malfunction.
¡
Cancel the setup mode.
¡
English
Notes
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this INSTRUCTION MANUAL for details on correct operations.
¡Playback from a desired track and random playback are not available during programme playback.
–49–
2C15
EN
TM
HANDLING PRECAUTIONS
SERVICING
Should your DVD/VCR become inoperative, do not try to correct the problem by yourself. There are no user­serviceable parts inside. Turn off, unplug the power cord, and take the unit to our Authorized Service Center.
CABINET CLEANING
¡Wipe the front panel and other exterior surfaces of
the DVD/VCR with a soft cloth immersed in lukewarm water and wrung dry.
¡Never use a solvent or alcohol. Do not spray
insecticide liquid near the DVD/VCR. Such chemicals may cause damage and discolouration to the exposed surfaces.
AUTO HEAD CLEANING
¡Automatically cleans video heads as you insert or
remove a cassette, so you can see a clear picture.
¡Playback picture may become blurred or interrupted
while the TV programme reception is clear. Dirt accumulated on the video heads after long periods of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in your DVD/VCR may need to be cleaned.
1. Please visit your local Audio/Video store and pur­chase a good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the prob­lem, consult our nearest Authorized Service Center.
NOTES:
Remember to read the instructions included with the
video head cleaner before use.
Clean video heads only when problems occur.
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
¡If the player still does not perform properly when it is operated while referring to the relevant sections and to
the TROUBLESHOOTING GUIDE in this INSTRUCTION MANUAL, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pick­up unit.
DISC HANDLING
¡Use discs which have the following logos on them.
(Optical audio digital discs.)
¡Handle the discs so that fingerprints and dust do not
adhere to the surfaces of the discs.
¡Always store the disc in its protective case when it is
not used.
¡To clean-off, use a soft cloth.
¡Do not use a hard cloth since this will mar the disc.
¡Wipe the disc in a straight line from center to edge.
¡Never wipe with a circular motion.
¡Do not use detergent or abrasive cleaning agents.
–50–
EN
2C15
SPECIFICATIONS
Product type: DVD/VCR player with Video Cassette Recorder
Discs: DVD video
Audio CD Video Cassette tape
Converter output: UHF Channel 22~69.
Power source: 220-240V~ +/- 10%, 50Hz +/- 0.5%
Power consumption: 30 W (standby: 5.7 W)
Operating temperature: 5°C to 40°C
Dimensions: W 17-1/8˝ (435 mm)
H 4˝ (99 mm)
D 10-1/2˝ (266 mm)
Weight: 8.8 lbs (4 kg)
¡Designs and specifications are subject to change without notice.
English
–51–
EN
2C15
MEMO
–52–
EN
2C15
MEMO
English
–53–
EN
2C15
BATTERY
SAFETY
GUIDELINES
Take care to fit your batteries correctly, observing the plus and minus marks on the battery and appliance. Incorrect fitting can cause leakage or in extreme cases, fire or even an explosion.
ALWAYS
Replace the whole set of batteries at one time, taking care not to mix old and new batteries or batteries of different types, since this can result in leakage or in extreme cases, fire or even an explosion.
ALWAYS
Used correctly, domestic batteries are a safe and dependable source of portable power. Problems can occur if they are misused or abused — resulting in leakage or, in extreme cases, fire or explosion. Here are some simple guidelines to safe battery use designed to eliminate any such problems.
PLEASE PHOTOCOPY AND DISPLAY
ALWAYS ALWAYS NEVER
Store unused batteries in their packaging and away from metal objects which may cause a short­circuit resulting in leakage or, in extreme cases, fire or even an explosion.
Remove dead batteries from equipment and all batteries from equipment you know you are not going to use for a long time. Otherwise the batteries may leak and cause damage.
Never dispose of batteries in fire as this can cause them to explode. Please put dead batteries in with the normal household waste.
NEVER ALWAYS NEVER
Never attempt to recharge ordinary batteries, either in a charger or by applying heat to them. They may leak cause fire or even explode. There are special rechargeable batteries which are clearly marked as such.
Supervise children if they are replacing
batteries themselves in order to ensure
these guidelines are followed.
Remember that small button cell batteries such as used in some hearing aids, toys, games and other appliances, are easily swallowed by young children and this can be dangerous.
ALWAYS ALWAYS ALWAYS
Keep loose button cells away from young children.
Make sure battery compartments are
secure.
Seek medical advice if you believe a
cell has been swallowed.
–54–
EN
2C15
SUBSIDIARY INFORMATION
SOME DOS AND DONTS ON THE SAFE USE OF EQUIPMENT
This equipment has been designed and manufactured to meet international safety standards but like any elec-
trical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
★★★★★★★★★★★
DO read the operating instructions before you attempt to use the equipment.
DO ensure that all electrical connections (including the mains plug, extension leads and interconnection between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions.
Switch off and withdraw the mains plug when making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
DO be careful with glass panels or doors on equipment.
★★★★★★★★★★★
DONT continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way switch off, withdraw the mains plug and consult your dealer.
DONT remove any fixed cover as this may expose dangerous voltages.
DONT leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a standby mode. Switch off using the switch on the equipment and make sure that your family know how to do this. Special arrangements may need to be made for infirm or handicapped people.
DONT use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is illegal to watch television whilst driving.
DONT listen to headphones at high volume, as such use can permanently damage your hearing.
DONT obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DONT use makeshift stands and NEVER fix legs with wood screws to ensure complete safety always fix the manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DONT allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
---NEVER let anyone especially children push anything into holes, slots or any other opening in the case this could result fatal electrical shock:
---NEVER guess or take chances with electrical equipment of any kind.
---it is better to be safe than sorry!
★★★★★★★★★★★
English
–55–
EN
2C15
HITACHI - YOUR GUARANTEE (UK & Ireland)
For the period of 12 MONTHS from the date of purchase your product has the benefit of our FULL PARTS AND LABOUR GUARANTEE as detailed below.
We undertake to replace of repair any part of the product which fails due to a manufacturing defect within 12 months of the date of purchase provided that.
1) The product has been installed and used only in accordance with the instructions supplied with the product.
2) The product has not been repaired maintained, or modified by any person other than our authorised Engineer.
3) The product serial number is not removed or altered.
This guarantee does not apply to products acquired second-hand or for commercial or communal use. This guarantee does not extend to user control adjustments, battery replacement and aerial adjustment. Any parts replaced
under guarantee shall become the property of HITACHI EUROPE LTD. Please note that evidence of the date of purchase will be required before service under guarantee is carried out.
This guarantee does not affect your statutory rights. In all cases of difficulty consult your HITACHI dealer.
HITACHI EUROPE LTD.
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire SL8 5XF
Tel:01628-643000 Fax:01628-643400 Email:consumer-service@hitachi-eu.com
www.hitachi-consumer-eu.com
Printed in China
TJ16061 C Hitachi, Ltd. 2002
0VMN03212
H9311BD
★★★★★
Hitachi, Ltd. Tokyo, Japan
International Sales Division
THE HITACHI ATAGO BUILDING,
No. 15 –12 Nishi Shinbashi, 2 – Chome,
Minato – Ku, Tokyo 105-8430, Japan.
HITACHI EUROPE LTD,
Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA
UNITED KINGDOM
Tel: 01628 643000 Fax: 01628 643400 Email: consumer-service@hitachi-eu.com
HITACHI EUROPE GmbH
Munich Office Dornacher Strasse 3 D-85622 Feldkirchen bei München
GERMANY
Tel: +49-89-991 80-0 Fax: +49-89-991 80-224 Hotline: +49-180-551 25 51 (12ct/min) Email: HSE-DUS.service@hitachi-eu.com
HITACHI EUROPE srl
Via Tommaso Gulli N.39, 20147 Milano, Italia
ITALY
Tel: +39 02 487861 Tel: +39 02 38073415 Servizio Clienti Fax: +39 02 48786381/2
Email: customerservice.italy@hitachi-eu.com
HITACHI EUROPE S.A.S
Lyon Office B.P. 45, 69671 BRON CEDEX FRANCE Tel: 04 72 14 29 70 Fax: 04 72 14 29 99 Email: france.consommateur@hitachi-eu.com
HITACH EUROPE AB
Egebækgård Egebækvej 98 DK-2850 Nærum
DENMARK
Tel: +45 43 43 6050 Fax: +45 43 60 51 Email: csgnor@hitachi-eu.com
Hitachi Europe Ltd
Bergensesteenweg 421 1600 Sint- Pieters-Leeuw
BELGIUM
Tel: +32 2 363 99 01 Fax: +32 2 363 99 00 Email: sofie.van.bom@hitachi-eu.com
www.hitachidigitalmedia.com
Tel: 03 35022111
HITACHI EUROPE S.A.
364 Kifissias Ave. & 1, Delfon Str. 152 33 Chalandri Athens
GREECE
Tel: 1-6837200 Fax: 1-6835964 Email: service.hellas@hitachi-eu.com
HITACHI EUROPE S.A.
Gran Via Carlos III, 101- 1 08028 Barcelona
SPAIN
Tel: 93 409 2550 Fax: 93 491 3513 Email: atencion.cliente@hitachi-eu.com
HITACHI Europe AB Box 77 S-164 94 Kista
SWEDEN
Tel: +46 (0) 8 562 711 00 Fax: +46 (0) 8 562 711 13 Email: csgswe@hitachi-eu.com
HITACHI EUROPE LTD (Norway) AB STRANDVEIEN 18 1366 Lysaker NORWAY Tel: 67 5190 30 Fax: 67 5190 32 Email: csgnor@hitachi-eu.com
HITACHI EUROPE AB
Neopoli / Niemenkatu 73 FIN-15140 Lahti
FINLAND
Tel : +358 3 8858 271 Fax: +358 3 8858 272 Email: csgnor@hitachi-eu.com
HITACHI EUROPE LTD
Na Sychrove 975/8 101 27 Praha 10 – Bohdalec
CZECH REPUBLIC
Tel: +420 267 212 383 Fax: +420 267 212 385 Email: csgnor@hitachi-eu.com
Loading...