Hitachi CP-X9110, CP-WX9210, CX-HD9320, CX-X9111, CX-WX-9211 Network Manual

...

Download

Page 1

Projector

CP-X9110/CP-WX9210/CP-WU9410/CP-HD9320 CP-X9111/CP-WX9211/CP-WU9411/CP-HD9321

User's Manual (detailed) Network Guide

Thank you for purchasing this product.

This manual is intended to explain only the network function. For proper use of this product, please refer to this manual and the other manuals for this product.

WARNING

►Before using this product, be sure to read all manuals for this

product. After reading them, store them in a safe place for future reference.

Features

This projector has the network function that brings you the following main features.

 Network Presentation : allows the projector to project computer images transmitted

through a network. (

 Web Control : allows you to monitor and control the projector through a network from a

computer. (

 My Image : allows the projector to store up to four still images and project them. (  Messenger : allows the projector to display text sent from a computer through a network.

80)

(

 Network Bridge : allows you to control an external device through the projector from a

computer. (

NOTE

36)

83)

• The information in this manual is subject to change without notice.

• The illustrations in this manual are for illustrative purposes. They may differ

slightly from your projector.

• The manufacturer assumes no responsibility for any errors that may appear in

this manual.

• The reproduction, transfer or copy of all or any part of this document is not

permitted without express written consent.

74)

78)

Trademark acknowledgment

• Microsoft of Microsoft Corporation in the U.S. and/or other countries.

• Adobe

• Pentium

• JavaScript

• HDMI registered trademarks of HDMI Licensing LLC in the United States and other countries.

• Crestron

RoomView

Electronics, Inc. in the United States and other countries.

• Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and areas.

All other trademarks are the properties of their respective owners.

, Internet Explorer®, Windows® and Windows Vista® are registered trademarks

and Flash

is a registered trademark of Intel Corporation.

is a registered trademark of Sun Microsystems, Inc.

, the HDMI logo and High-Deﬁnition Multimedia Interface are trademarks or

, Crestron e-Control®, e-Control®,Crestron Connected

and RoomView

are registered trademarks of Adobe Systems Incorporated.

, Fusion RV

are trademarks or registered trademarks of Crestron

,Crestron

Page 2

Contents



Caution .......................................................................................... 4

1. Network Function ..................................................................... 5

1.1 Web Control ................................................................................................ 5

1.2 Network Presentation . ................................................................................ 6

1.3 My Image Function ..................................................................................... 7

1.4 Messenger Function ................................................................................... 8

1.5 Network Bridge Function .............................................................................9

1.6 Other Functions .........................................................................................10

1.6.1 E-mail Alerts ................................................................................................................... 10

1.6.2 Projector Management using SNMP .............................................................................. 10

1.6.3 Event Scheduling ........................................................................................................... 10

1.6.4 Command Control via the Network ................................................................................ 10

2. Connection to the network .................................................... 11

2.1 System requirements ............................................................................... 11

2.2 Connection via wired LAN ......................................................................... 12

2.3 Connection setup of Wired LAN ............................................................... 12

2.4 Connection via wireless LAN .................................................................... 14

2.4.1 Connection in Ad Hoc Mode .......................................................................................... 15

2.4.2 Connection in Infrastructure Mode ................................................................................. 16

2.5 Applications .............................................................................................. 18

2.6 NETWORK Menu . .................................................................................... 20

3. Web Control ............................................................................ 36

3.1 Projector Web Control ...............................................................................38

3.1.1 Login .............................................................................................................................. 38

3.1.2 Network Information ....................................................................................................... 39

3.1.3 Network Settings ............................................................................................................ 40

3.1.4 Port Settings .................................................................................................................. 44

3.1.5 Mail Settings .................................................................................................................. 46

3.1.6 Alert Settings .................................................................................................................. 47

3.1.7 Schedule Settings .......................................................................................................... 49

3.1.8 Date/Time Settings ......................................................................................................... 53

3.1.9 Security Settings ............................................................................................................ 55

3.1.10 Projector Control .......................................................................................................... 56

3.1.11 Remote Control ............................................................................................................ 61

3.1.12 Projector Status ........................................................................................................... 62

3.1.13 Network Restart ........................................................................................................... 63

3.1.14 Connection Test ........................................................................................................... 64

Page 3

Contents

3.2 Crestron e-Control

3.2.1 Main window .................................................................................................................... 67

3.2.2 Tools window ................................................................................................................... 69

3.2.3 Info window ..................................................................................................................... 71

3.2.4 Help Desk window ........................................................................................................... 72

3.2.5 Emergency Alert .............................................................................................................. 73

.................................................................................. 65

4. Network Presentation ............................................................. 74



4.1 Outline ...................................................................................................... 74

4.2 Display Mode . ........................................................................................... 75

4.2.1 Single PC mode ............................................................................................................. 75

4.2.2 Multi PC mode ............................................................................................................... 75

4.3 Multi Projector Mode . ............................................................................... 76

4.4 Moderator Control Mode . ......................................................................... 76

4.5 Port Number . ............................................................................................ 77

5. My Image Function ................................................................. 78

6. Messenger Function ............................................................... 80

6.1 Outline ...................................................................................................... 80

6.2 Supported Languages .............................................................................. 81

6.3 Display Style ............................................................................................. 81

7. Network Bridge Function ....................................................... 83

7.1 Connecting devices .................................................................................. 83

7.2 Communication setup ............................................................................... 84

7.3 Communication port ................................................................................. 84

7.4 Transmission method ............................................................................... 85

7.4.1 HALF-DUPLEX .............................................................................................................. 85

7.4.2 FULL-DUPLEX ............................................................................................................... 86

8. Other Functions ...................................................................... 87

8.1 E-mail Alerts ............................................................................................. 87

8.2 Projector Management using SNMP ........................................................ 90

8.3 Event Scheduling ..................................................................................... 92

8.4 Command Control via the Network .......................................................... 95

8.5 Crestron Connected ............................................................................... 100

9. Troubleshooting ................................................................... 101

10. Warranty and after-sales service ...................................... 109

Page 4

Caution

To use the wireless network function of this projector, the designated USB wireless adapter sold as an option is required. For precautions according to the stan-

dards and laws, refer to the documents that come with the adapter.

[Restriction on plugging and unplugging the USB wireless adapter]

Before you insert or pull out the USB wireless adapter from the projector, turn off the power of the projector and pull out the power cord’s plug from the outlet. Do not touch the USB wireless adapter that is connected to the projector while the projector is receiving AC power. Do not use any extension cable or device when connecting the adapter to the projector.

[Security precautions when using wireless LAN]

It is recommended that security settings, such as SSID and ENCRYPTION, are speciﬁed when using wireless LAN communication. If the security settings are not speciﬁed, the contents may be intercepted or it may cause unauthorized access

to the system. For details on wireless LAN security settings, refer to 3.1 Projector

Web Control.

CAUTION

►The optional IEEE802.11b/g/n USB wireless adapter uses the 2.4GHz radio frequency band. You do not need a radio license to use the adapter, but you

should be aware of the following:

• DO NOT USE NEAR THE FOLLOWING!

• Microwave ovens

• Industrial, scientiﬁc or medical devices

• Designated low power radio stations

• Premises radio stations

Using the USB wireless adapter near the above may cause radio interference,

which would result in a decrease in transmission speed or interruption, and

even lead to malfunctioning of devices such as pacemakers.

• Depending on the location where the USB wireless adapter is used, radio wave

interference may occur, which may result in a decrease in transmission speed or interruption in communication. In particular, please be aware that using the

USB wireless adapter at locations where there is reinforced steel, other types of metals or concrete is likely to cause radio wave interference.

• Available Channels

The USB wireless adapter uses the 2.4GHz radio frequency band, but

depending on the country or region you are in, the channels that you can use

might be limited. Please consult your dealer for information on the usable

channels.

• Bringing the optional USB wireless adapter out of the country or region you reside in and using it there could lead to a violation of the radio laws of that

country or region.

Page 5

1. Network Function

This chapter describes the outline of network function.

1.1 Web Control

Connecting the projector and the computer via the network, remote control and

status monitoring of the projector can be performed by Web browser.

Two types of interface, ”Projector Web Control” and “Crestron e-Control”, are available for this projector. (

36 Chapter 3)

CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411

Projector Web Control

CP-HD9320/HD9321

Crestron e-Control

Page 6

1. Network Function

1.2 Network Presentation

The projector can display the computer screen images transmitted through the network.

To use Network Presentation, an exclusive application, "LiveViewer" is required. The following application is required to use Network Presentation.

OS Application

Windows LiveViewer

Mac OSX LiveViewer iOS(iPhone/iPad) Projector Quick Connection

Page 7

1. Network Function

1.3 My Image Function

The projector can display still images transferred via the network. It is possible to allocate up to 4 image ﬁles. MY IMAGE transmission requires an exclusive application for your computer. Use the application to transfer the image data.

Transfer image data

Display image data (ex.

)

Page 8

1. Network Function

1.4 Messenger Function

The projector can display text data transferred via the network on the screen.

It is possible to store up to 12 text data.

Transfer text data

Display text data (ex.

)

Page 9

1. Network Function

1.5 Network Bridge Function

This projector is equipped with the NETWORK BRIDGE function to perform mutual conversion of a network protocol and a serial interface. By making use of the NETWORK BRIDGE function, a computer connected to the projector via wireless or wired LAN is able to control an external device via RS-232C communication using the projector as a network terminal.

Computer

CONTROL port

TCP/IP data Serial data

Wired LAN

LAN cable

Wireless

LAN

Protocol change

RS-232C

RS-232C cable

WIRELESS port

(USB wireless adapter)

LAN port

External device

Page 10

1. Network Function

1.6 Other Functions

1.6.1 E-mail Alerts

The projector can automatically send an alert message to the speciﬁed e-mail addresses when the projector detects a certain condition that is requiring

maintenance or detected an error. (

87 Chapter 8-1)

1.6.2 Projector Management using SNMP

The SNMP (Simple Network Management Protocol) enables to manage the

projector information, which is a failure or warning status, from the computer on

the network. The SNMP management software will be required on the computer

to use this function. (

90 Chapter 8-2)

1.6.3 Event Scheduling

The scheduling function enables to setup scheduled events including power on / power off. It enables to be “self-management” projector. The schedule can be set in Projector Web Control or SETUP-SCHEDULE menu

in the projector. (

92 Chapter 8-3)

1.6.4 Command Control via the Network

You can conﬁgure and control the projector via the network using RS-232C

commands. (

95 Chapter 8-4)

Page 11

2. Connection to the network

2.1 System requirements

The following equipments are required to connect the projector to your computer

through the network.

Ŷ&RPPRQ The projector: 1 unit, Computer: 1 or more sets Ŷ&RQQHFWLQJGHYLFHIRUWKHSURMHFWRUDQGWKHFRPSXWHU

1) For the wired connection *1

LAN cable (CAT-5e or greater): 1 piece

2) For the wireless connection *2

- Projector side IEEE802.11b/g/n USB wireless adapter (option : USB-WL-11N): 1 unit *3

- Computer side IEEE802.11b/g/n wireless LAN equipment: 1 unit for each computer *4

*1: The system for using the network function of the projector requires

communication environment conforming to 100Base-TX or 10Base-T.

*2: An access point is required when the wireless LAN connection is used as

Infrastructure mode.

*3: Available encryption methods are as follows. This product cannot be

connected to the wireless network using other encryption method.

WPA2-PSK (AES) WPA2-PSK (TKIP) WPA-PSK (AES) WPA-PSK (TKIP) WEP 128bit WEP 64bit

*4: Depending on the type of wireless network device and computer you are using,

the projector may not be able to communicate properly with your computer,

even if the computer is equipped with a built-in wireless LAN function.

To eliminate communication problems, use a Wi-Fi certiﬁed wireless network device.

■ Web browser

Web browser is required to be installed in your computer to use Web control.

■ Application

Exclusive applications are required to be installed in your computer to use Network Presentation, My Image and Messenger. Refer to (

For Mac users: Mac OS does not support some applications. Refer to System Requirements for Applications (

NOTE

to SAVING and the projector is in standby mode. Connect the projector to the network after setting STANDBY MODE to NORMAL. (

Operating Guide)

• The network function is not available when STANDBY MODE is set

18) ﬁrst before setting up the connection.

SETUP menu in the

18).

Page 12

2. Connection to the network

2.2

The connection via wired LAN is available. Set wired LAN for the projector by

following the instructions of your network administrator when connecting to the existing network.

㻯㼛㼚㼚㼑㼏㼠㼕㼛㼚㻌㼢㼕㼍㻌㼣㼕㼞㼑㼐㻌㻸㻭㻺

hub

2.3 Connection setup of Wired LAN

1) Connect the projector to the computer via a hub

with a LAN cable (CAT-5e or higher).

2) Press the MENU button on the remote control or the

control panel of the projector.

The MENU you last used will appear. Use the cursor button to select the following.

EASY MENU > ADVANCED MENU > NETWORK > WIRED SETUP

3) Set the following items in WIRED SETUP.

䡡㻌㻌DHCP 䡡㻌IP ADDRESS 䡡㻌SUBNET MASK 䡡㻌DEFAULT GATEWAY 䡡㻌DNS SERVER

As for setting an IP address, refer to “About IP address”. (

Select APPLY, then press the ENTER button to reﬂect the settings.

13)

Page 13

2. Connection to the network

[About IP address]

■ Setting manually The Network address portion of the IP address setting on your computer must be the same as the setting on the projector. Also, the entire IP address on the computer must not overlap with that of the other devices on the same network,

including the projector. The projector’s settings are as follows.

IP address: 192.168.1.254 Subnet mask: 255.255.255.0

(Network address: 192.168.1 in this case)

Therefore, specify the computer’s IP address as follows. IP address: 192.168.1.xxx (xxx shows decimal number.) Subnet mask: 255.255.255.0

(Network address: 192.168.1 in this case) For example

Select from 1 to 254 for “xxx” not duplicating with any other equipments. In this case, since the IP address of the projector is “192.168.1.254”, specify a

setting between 1 to 253 for the computer.

■ Setting automatically When a DHCP server exists in the connected network, it assigns an IP address to the projector and the computer automatically. If DHCP server is not available, set IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY.

NOTE

• Although HDBaseT and LAN port can be used for wired LAN, they cannot be used simultaneously. Connect LAN cable to the port set in WIRED NETWORK

on NETWORK menu.

•

The same network address cannot be used for both wireless LAN and wired LAN.

•

If the projector and the computer exist in the same network (i.e., same network

address), you can leave the default gateway ﬁeld blank.

• When the projector and the computer exist in different networks, the default gateway must be set. Consult to the network administrator in detail.

Page 14

2. Connection to the network

2.4

㻯㼛㼚㼚㼑㼏㼠㼕㼛㼚㻌㼢㼕㼍㻌㼣㼕㼞㼑㼘㼑㼟㼟㻌㻸㻭㻺

Connection via wireless LAN is available with option parts, USB wireless adapter (USB-WL-11N). Wireless LAN has two types of connection, Ad Hoc and Infrastructure.

Fig. 2.4.a Without an access point communication (Ad Hoc)

Fig. 2.4.b With an access point communication (Infrastructure)

* Ad Hoc is one of the wireless LAN communication methods without having an

access point to communicate.

* Infrastructure is one of the wireless LAN communication methods with having

an access point to communicate. If communicating with existing network, consult with your network administrator.

NOTE

• Network settings can also be changed in Network Settings of Projector Web Control㻚

• Wireless LAN initial settings for the projector are as follows. Mode: Ad Hoc DHCP: Off IP address: 192.168.10.254 Subnet Mask: 255.255.255.0 Default Gateway: 0.0.0.0 SSID: wireless

Encryption: Off

Channel: 1

• The same network address cannot be used for both wireless LAN and wired LAN.

Page 15

2. Connection to the network

2.4.1 Connection in Ad Hoc Mode

Set the following when connecting the projector and the computer in Ad Hoc mode.

Projector setting

[Restriction on plugging and unplugging the USB wireless adapter] Before you insert or pull out the USB wireless adapter from the projector, turn off the power of the projector and pull out the power cord’s plug from the outlet. Do not touch the USB wireless adapter that is connected to the projector while the projector is receiving AC power. Do not use any extension cable or device when connecting the adapter to the

projector

1) Attach the USB wireless adapter to the WIRELESS port of the projector.

2) Turn on the projector.

3) Press the MENU button on the remote control or the control panel of the projector.

The MENU you last used will appear. Use the cursor button to select the following.

EASY MENU > ADVANCED MENU > NETWORK > WIRELESS SETUP

4) Set the following items in WIRELESS SETUP.

䡡㻌MODE: ADHOC 䡡㻌㻌DHCP 䡡㻌IP ADDRESS 䡡㻌SUBNET MASK 䡡㻌SSID 䡡㻌ENCRYPTION 䡡㻌CH

As for setting an IP address, refer to “About IP address”. (

13)

Select APPLY, then press the ENTER button to reﬂect the settings.

Computer setting

1) Set IP ADDRESS and SUBNET MASK for the computer according to IP ADDRESS and SUBNET MASK set for the projector. Set the projector and the computer so that they can have the same network address.

2) Select SSID set for the projector by following the procedure of wireless

connection of the computer. Enter encryption key by following the computer’s instruction if it is encrypted.

NOTE

• As for the procedure of setting network and wireless connection for the

computer, refer to the manual of computer or wireless LAN device.

Page 16

2. Connection to the network

2.4.2 Connection in Infrastructure Mode

Set the following when connecting the projector and the computer in Infrastructure

mode.

projector.

1) Attach the USB wireless adapter to the WIRELESS port of the projector.

2) Turn on the projector.

3) Press the MENU button on the remote control or the control panel of the projector.

The MENU you last used will appear. Use the cursor button to select the following.

EASY MENU > ADVANCED MENU > NETWORK > WIRELESS SETUP

4) Set the following items in WIRELESS SETUP.

䡡㻌MODE: INFRASTRUCTURE 䡡㻌㻌DHCP 䡡㻌IP ADDRESS 䡡㻌SUBNET MASK 䡡㻌DEFAULT GATEWAY 䡡㻌DNS SERVER 䡡㻌SSID 䡡㻌ENCRYPTION 䡡㻌CH

As for setting an IP address, refer to “About IP address”. (

13)

Select APPLY, then press the ENTER button to reﬂect the settings.

Page 17

2. Connection to the network

Connection in Infrastructure Mode (continued)

SSID SCAN LIST function

The connection can be set up by selecting from SSID SCAN LIST without setting SSID and ENCRYPTION in WIRELESS SETUP. The procedure of connecting by SSID SCAN LIST is as follows.

1) Select SSID SCAN LIST in WIRELESS SETUP on NETWORK menu.

The list of SSID in wireless network is displayed.

2) Select SSID in wireless network that you want to connect in SSID SCAN LIST.

The display to enter the encryption key appears if it is encrypted. Enter the encryption key by using software keyboard.

3) The icon indicating “connected” ( ) is displayed in SSID SCAN LIST screen when the connection is complete.

NOTE

•㻌

Transmission speed may be slow depending on the settings of an access point.

•

If the projector and the computer exist in the same network (i.e., same network

address), you can leave the default gateway ﬁeld blank.

• When the projector and the computer exist in different networks, the default gateway must be set. Consult with the network administrator in detail.

• Set wireless LAN for the projector by following the instructions of your network

administrator when connecting to the existing network.

• Open System Authentication is used for WEP encryption, and Shared Key Authentication is not supported. The authentication with an access point succeeds and it is regarded that the connection is established normally even when

entering illegal encryption key due to Open System Authentication,but data cannot actually be transmitted.

•

IP ADDRESS, SUBNET MASK, and DEFAULT GATEWAY should be set in

advance when DHCP is set to OFF.

Page 18

2. Connection to the network

2.5 Applications

The latest version of the application software can be downloaded from the website

below.

http://www.hitachi-america.us/projectors http://www.hitachidigitalmedia.com/ http://www.hitachi-dm.cn/ http://www.hitachi.co.jp/proj/

For iOS Network Presentation software, refer to the URL below for details and downloads of Projector Quick Connection.

http://www.hitachi.co.jp/Prod/vims/proj/en/ http://www.hitachi.co.jp/proj/

[System Requirements for Applications]

Application Hardware and Software LiveViewer [Windows]

OS: Windows® XP Windows Vista® (Service Pack 1 or later)

Windows 7

Windows 8/ 8.1

Graphic card: VGA: 640x480 or higher (recommended XGA: 1024x768)

CPU: Pentium 4 (2.8 GHz or higher)

Hard disk space: 100MB or higher

Page 19

[System Requirements for Applications] (continued)

Application Hardware and Software

LiveViewer [Mac]

Mac OSX 10.5 Mac OSX 10.6 Mac OSX 10.7 Mac OSX 10.8

Hard disk space: 15MB or higher

NOTE

•

Only for Intel version. Power Mac is not supported.

• LiveViewer CD-ROM.

for MAC is not included in the bundled

Download it from the website.

2. Connection to the network

Projector Quick Connection

Projector Image Tool (PJImg)

Projector Messenger Tool (PJMessenger)

iOS 5.1.1 or later iPad, iPad2, New iPad iPhone4/4S/5

OS: Windows® XP

Windows Vista® Windows 7

Windows 8/ 8.1

CPU: Pentium 3 (500MHz or higher)

Hard disk space: 20MB or higher

OS: Windows® XP

Windows Vista® Windows 7

Windows 8/ 8.1

CPU: Pentium 3 (500MHz or higher)

Hard disk space: 20MB or higher

Page 20

2. Connection to the network

2.6 NETWORK Menu

Remember that incorrect network settings on this

projector may cause trouble on the network. Be sure

to consult with your network administrator before connecting to an existing access point on your network.

Select “NETWORK” from the main menu to access to

the following functions.

Select an item using the ▲/▼ cursor buttons on the projector or remote control, and press the ► cursor button on the projector or

remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table.

NOTE

• When you use wired LAN, ﬁrst select which function to use, LAN or

HDBaseT, in WIRED NETWORK menu.

• To use the wireless network function of this projector, the designated USB wireless adapter sold as an option is required. Do not use any extension cable or device when connecting the adapter to the projector.

•

The projector does not allow both wireless and wired LAN to be connected to

the same network.

• Do not set the same network address for both wireless and wired LAN.

• If you do not use SNTP, then you must set the DATE AND TIME during the

initial installation.

• The network function is not available when STANDBY MODE is set to SAVING and the projector is in standby mode. Connect the projector to the network after setting STANDBY MODE to NORMAL. (

SETUP menu in the

Operating Guide)

Page 21

2. Connection to the network

Item Description

Any name can be set to the projector to identify it on the

network.

(1) Select the PROJECTOR

NAME and press the ► button. The PROJECTOR NAME dialog will be displayed.

Use displayed software keyboard to enter PROJECTOR NAME.

DELETE : Deletes one character. CLEAR ALL: Deletes all characters. CANCEL : Goes back to network menu after discarding

the entered characters.

OK : Goes back to network menu after saving the entered

characters.

PROJECTOR

NAME

(2) The current PROJECTOR NAME will be displayed on the

ﬁrst 3 lines. Particular projector name is pre-assigned by default.

Use the ENTER or INPUT button to select and enter characters. To erase 1 character at one time, press the RESET button

or press the ◄ and INPUT button at the same time. Also if

you move the cursor to DELETE or CLEAR ALL on screen

and push the ENTER or INPUT button, 1 character or

all characters will be erased. Up to 64 characters can be input for the PROJECTOR NAME.

(3) To change an already inserted

character, move the cursor to one of the ﬁrst 3 lines, and move the cursor on the

character to be changed.

After pressing the ENTER or INPUT button, the character is

selected. Then, follow the same procedure as described at the

item (2) above.

(4) To ﬁnish entering text, move the cursor to the OK on

(continued on next page)

screen and press the ►, ENTER or INPUT button. To

revert to the previous PROJECTOR NAME without saving changes, move the cursor to the CANCEL on screen and

press the ◄, ENTER or INPUT button.

Page 22

2. Connection to the network

Item Description

Conﬁgures wireless network. Setting values are saved after

selecting APPLY.

NOTE

Setting values are not saved if Menu dissapears before selecting Apply.

WIRELESS

SETUP

SSID SCAN LIST

Searches available wireless network and displays the list of SSID.

You can select SSID to connect from the list. (1) SSID on available wireless network is

displayed after selecting SCAN LIST and press the ► button.

NOTE

The wireless network using the encryption method not supported by the projector is not displayed in the search list.

(continued on next page)

Page 23

Item Description

Icon Description

㻌㻌㻌㻌

The projector is connecting to the wireless network.

The wireless network is encrypted.

The intensity of radio wave.

Device set for Ad Hoc.

(2) Select SSID that you want to connect and press the ► or ENTER button. The display to enter the encryption key appears if SSID

is encrypted. Enter the characters by using software keyboard.

Move the cursor to OK and press the ►, ENTER

WIRELESS

SETUP

(continued)

SSID SCAN LIST

(continued)

or INPUT button after entering.

2. Connection to the network

(continued on next page)

NOTE

If you select the [HIDE THE CHARACTERS]

checkbox, the characters are hidden.

Page 24

2. Connection to the network

Item Description

The OSD below is displayed while the

㻔㻟㻕㻌

connection is in progress.

The keys other than Reset button are not

available while the connection is in progress.

The connection process is interrupted when pressing the Reset button.

The OSD below is displayed when the connection

process is complete.

The message below is displayed when the connection is not established correctly.

Connection succeeded

䠖

WIRELESS

SETUP

(continued)

SSID SCAN LIST

(continued)

Connection failed

䠖

Encryption Lock enabled

䠖

NOTE

･Encryption settings cannot be

changed when encryption lock is enabled

in Network Settings – Wireless Setup in

Projector Web Control. Refer to Encryption

Lock. (

41)

• Open System Authentication is used for WEP encryption, and Shared Key Authentication

is not supported. The authentication with an access point is succeeded and it is regarded that the connection is established normally

even when entering illegal encryption key

due to Open System Authentication,but data

cannot actually be transmitted.

(continued on next page)

The icon indicating the connection status

㻔㻠㻕㻌

(

) is displayed in SSID SCAN LIST when the

connection is complete.

Page 25

2. Connection to the network

Item Description

SSID SCAN LIST

(continued)

Switches between ADHOC and INFRASTRUCTURE. Select the mode of the network communication system. Select according to the settings of your

computer.

WIRELESS

SETUP

(continued)

MODE

DHCP

ADDRESS

AD HOC  INFRASTRUCTURE

To save the setting, press the ► button.

NOTE

cannot be used.

• If ADHOC is set to MODE while WPA-PSK or WPA2-PSK is selected in ENCRYPTION, the

ENCRYPTION (

automatically.

• When ADHOC is selected, IEEE802.11n

27) setting switches to OFF



Conﬁgures whether IP address is automatically

obtained or not.

Use the ▲/▼ buttons to turn DHCP on/off.

ON  OFF

Conﬁgures the IP address when DHCP is disabled. Enter the IP ADDRESS. This function can only be used when DHCP is set

to OFF.

(continued on next page)

Page 26

2. Connection to the network

Item Description

Conﬁgures the subnet mask when DHCP is

disabled.

SUBNET

MASK

Enter the SUBNET MASK. This function can only be used when DHCP is set

to OFF.

Conﬁgures the default gateway when DHCP is

disabled.

DEFAULT

GATEWAY

Enter the DEFAULT GATEWAY address. This function can only be used when DHCP is set

to OFF.

Conﬁgures the DNS server address. Enter the DNS server address.

WIRELESS

SETUP

(continued)

DNS

SERVER

SSID

NOTE

This setting cannot be obtained automatically.

Conﬁgures SSID for wireless network.

Select one of the DEFAULT (#1~#4) and press ►

or ENTER button.

To adjust CUSTOM

Press the ► or ENTER button when the # 5

CUSTOM is selected. The SSID #5 CUSTOM

menu will be appeared.

Enter SSID by using software keyboard. Refer to PROJECTOR NAME (

21) for how to use

software keyboard.

(continued on next page)

Page 27

2. Connection to the network

Item Description

Select the encryption method to be used.

WIRELESS

SETUP

(continued)

ENCRYPTION

WPA2-PSK(AES)

WPA2-PSK(TKIP)



  OFF WPA-PSK(AES)  

WEP 64bitWEP 128bitWPA-PSK(TKIP)

It is required to enter the encryption key when

selecting the encryption method other than

OFF and pressing the ► button.

NOTE

selected when Ad Hoc is set.

• WPA2-PSK (AES) is recommended for encryption

method of IEEE802.11n. Transmission speed in IEEE802.11n may be slow when other encryption

method (WEP, WPA-PSK (TKIP), WPA2-PSK (TKIP)). Change the setting to “AES” if encryption other than “AES” is set.

• Encryption method not included in the selected item cannot be available.

• Only WEP64bit or WEP128bit can be

(continued on next page)

Select the channel of the wireless LAN to be used while MODE (

25) is set to ADHOC.

Select according to the settings of your computer. The channels 1 to 11 are available. To save the setting, press the ► button.

• The available channels vary depending on a

country.

Page 28

2. Connection to the network

Item Description

Conﬁgures wired network.

Setting values are saved

after selecting APPLY.

NOTE

Setting values are not saved if Menu disappears before selecting APPLY.

WIRED SETUP

DHCP

ADDRESS

SUBNET

MASK

(continued on next page)

Conﬁgures whether IP address is automatically

obtained or not.

Use the ▲/▼ buttons to turn DHCP on/off.

ON  OFF

Conﬁgures the IP address when DHCP is disabled. Enter the IP ADDRESS. This function can only be used when DHCP is set

to OFF.

Conﬁgures the subnet mask when DHCP is disabled. Enter the SUBNET MASK. This function can only be used when DHCP is set

to OFF.

Page 29

Item Description

Conﬁgures the default gateway when DHCP is

DEFAULT

GATEWAY

disabled.

Enter the DEFAULT GATEWAY address. This function can only be used when DHCP is set

to OFF.

WIRED SETUP

(continued)

Conﬁgures the DNS server address. Enter the DNS server address.

2. Connection to the network

DNS

SERVER

(continued on next page)

NOTE

This setting cannot be obtained automatically.

Page 30

2. Connection to the network

Item Description

Selecting this item displays the dialog for viewing the wireless and wired LAN settings. Use the ▲/▼ buttons to switch the page.

NETWORK INFORMATION

The ﬁrst page shows the wireless LAN settings. The second page is for the wired LAN settings, and the third page is for common

setting item.

The following information is displayed.

PASSCODE

䡡㻌

MODE

䡡㻌

IP ADDRESS

䡡㻌

SUBNET MASK

䡡㻌

DEFAULT GATEWAY

䡡㻌

DNS SERVER

䡡㻌

MAC ADDRESS

䡡㻌

SSID

䡡㻌

ENCRYPTION

䡡㻌

SPEED

䡡㻌

WIRELESS INFORMATION

(continued on next page)

Passcord supports the connection between the

projector and the computer when using Network Presentation. Refer to Network Presentation (74)

for the details.

NOTE

• IP ADDRESS, SUBNET MASK and

DEFAULT GATEWAY indicate “0.0.0.0” in the

following condition.

(1) The USB wireless adapter is not inserted

into the projector.

(2) DHCP is ON and the projector does not get address from DHCP server.

•

Nothing (blank) is shown in the CH and SPEED

ﬁelds if the USB wireless adapter is not inserted.

Page 31

Item Description

The following information is displayed.

PASSCODE

䡡㻌

IP ADDRESS

䡡㻌

SUBNET MASK

䡡㻌

DEFAULT GATEWAY

䡡㻌

DNS SERVER

䡡㻌

MAC ADDRESS

䡡㻌

WIRED INFORMATION

Passcord enables the projector and the computer

to be connected to the network easily when

using Network Presentation. Refer to Network Presentation (

NETWORK INFORMATION (continued)

NOTE

• IP ADDRESS, SUBNET MASK and DEFAULT GATEWAY indicate “0.0.0.0” when DHCP is ON and the projector has not gotten address from DHCP server.

2. Connection to the network

74) for details.

OTHER INFORMATION

(continued on next page)

The following information is displayed.

PROJECTOR NAME

䡡㻌

DATE AND TIME

䡡㻌

SNTP SERVER

䡡㻌

TIME DIFFERENCE

䡡㻌

• PROJECTOR NAME and SNTP SERVER may

appear truncated if they are too long.

Page 32

2. Connection to the network

Item Description

When you get the time via the network, specify SNTP server with IP address or domain name. Up to 255 characters can be entered for domain

name.

SNTP SERVER

SNTP SETUP

TIME DIFFERENCE

(continued on next page)

They are entered by using software keyboard.

Refer to PROJECTOR NAME(

21) for how to use

software keyboard.

NOTE

Set the time difference when using SNTP.

Enter the time difference.

Set the same time difference as the one set on

your computer. If unsure, consult your network administrator.

Use the ► button to return to the menu after setting the TIME DIFFERENCE.

Page 33

2. Connection to the network

Item Description

Selecting this item displays the MY

IMAGE menu.

Use the application to transfer the

image data. It can be downloaded

from the Hitachi web site.

MY IMAGE

Refer to 5. My Image Function (

78) for the details of MY

IMAGE.

Select an item of still image by the MY IMAGE and the ► or

ENTER button to display the image.

• The item without stored image cannot be selected.

• Each image name is displayed in 16 characters or less.

To switch the image displayed

Use the ▲/▼ buttons.

To return to the menu

Press the ◄ button on the remote control.

7RHUDVHWKHGLVSOD\HGLPDJHDQGLWVVRXUFH¿OHLQWKH

projector.

(1) Press the RESET button on the

remote control while displaying an

image to display the MY IMAGE DELETE menu.

(2) Press the ► button to erase.

To stop erasing, press the ◄ button.

Use the ▲/▼ buttons to turn the AMX Device Discovery on/off.

AMX D.D.

(AMX Device

Discovery)

(continued on next page)

When ON is selected, the projector can be detected by

controllers of AMX connected to the same network. For the details of AMX Device Discovery, visit the AMX web site.

ON  OFF

URL: http://www.amx.com/

Page 34

2. Connection to the network

Item Description

To use Network Presentation, an exclusive application is required. It can be installed from the bundled application CD. You can also download the latest version and relevant information from the Hitachi website.

PRESENTATION

Refer to 4. Network Presentation ( Network Presentation.

If you set a computer to the Presenter mode while

its image is projected, the projector is occupied by the computer and access from any other computer is

QUIT

PRESENTER

MODE

MULTI PC

MODE

blocked.

Use this function to quit the Presenter mode and

allow other computers to access the projector.

Select this item to display a dialog.

Press the ► button to choose OK in the dialog.

The Presenter mode is cancelled and a message is

displayed indicating the result.

If you set one or more computers to the Multi PC

mode and send their images to the projector, you can select the display mode on the projector from two options below.

- Single PC mode: displays the image of the selected

computer on full screen.

- Multi PC mode: displays the images sent from up to four computers on screen that is divided into quarter

sections.

Select this item to display a dialog. Use the dialog to change the display mode as

explained below.

• To change from Multi PC mode to Single PC mode,

select one of computers in the dialog using the ▲/▼/◄/► buttons and press the ENTER or INPUT button.

Press the ► button to choose OK, and then press

ENTER or INPUT again. The image for the selected computer is displayed on full screen.

74) for the details of

(continued on next page)

Page 35

Item Description

PRESENTATION

(continued)

MULTI PC

MODE

(continued)

2. Connection to the network

• To change from Single PC mode to Multi PC

mode, press the ► button to choose OK in the

dialog and press the ENTER or INPUT button. The display mode is changed.

• The Presenter mode setting

of the selected computer

becomes valid when the

display mode is changed to

Single PC mode. Also, the Presenter mode setting becomes invalid when the display mode is changed to Multi PC mode,

regardless of the setting on the computers.

WIRED

NETWORK

DISPLAY

USER NAME

Selecting this item displays the user name. This

function helps you identify from which computer the current image is sent.

Selects whether to use LAN or HDBaseT port.

LAN 䋽 HDBaseT

NOTE

Only either LAN or HDBaseT port can be used for the connection to the network. Switch it according to the environment.

Page 36

3. Web Control

You can adjust or control the projector via a network from a web browser on a

computer connected to the same network.

■Projector Web Control

㻌㻌You can control the projector, collect

the status such as lamp time, and set

e-mail or schedule, etc. in Projector Web Control.

Recommended web browser ･Internet Explorer

6/ 7/ 8/ 9/ 10/ 11

NOTE

• Internet Explorer

• If JavaScript JavaScript for your web browser for details on how to enable JavaScript

• Web browsers other than recommended ones may not work.

6.0 or later is required.

is disabled in your web browser conﬁguration, you must enable

in order to use the projector web pages properly. See the Help ﬁles

• It is recommended that all web browser updates are installed.

• If data is transferred via wireless and wired LAN at the same time, the

projector may not process the data correctly.

■Crestron e-Control

䚷Crestron e-Control

is a control interface using a web browser provided by

Crestron Electronics, Inc..

Crestron e-Control

CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411

can control and monitor the projector.

CP-HD9320/HD9321

(continued on next page)

Page 37

3. Web Control

NOTE

Adobe e-Control

• Crestron e-Control

Flash

Player on your computer to use Crestron e-Control®. Crestron

is not displayed in a web browser that does not support Flash®.

• If Crestron e-Control

is created using Flash

in the Network Settings (43) is set to Disable, the

. You need to install

selection window does not appear, but the Login window of the Projector Web Control is displayed.

Refer to the following for conﬁguring or controlling the projector via a web browser. Make sure that your computer and the projector is connected via network, and

then start Web browser.

Enter the projector's IP address into URL input box of the Web browser as the

example below, and then press the Enter key or

button.

Example: If the IP address of the projector is set to 192.168.1.10:

Enter “http://192.168.1.10/” into the address bar of the web browser

and press the Enter key or click

button.

If a correct URL is input, and the

projector and your computer are connected to the same network correctly, the selection window will be displayed.

NOTE

• Do not control the projector with the projector's menu or remote

control, and via Web Control at the same time. It may cause some operational

errors in the projector.

• The language used on the Projector Web Control is the same as that of the OSD on the projector. If you want to change it, you need to change the OSD

language on the projector. (

SCREEN menu in the Operating Guide)

Page 38

3. Web Control

3.1 Projector Web Control

3.1.1 Login

To use the Projector Web Control function, you need

to login with your user name and password.

Below are the factory default settings for user

name and password.

User name Administrator

Password <blank>

Enter your user name and password, and then click the [OK]. If you login successfully, the screen below will be displayed.

Main menu

Click the desired operation or conﬁguration item on the main menu.

Page 39

3.1 Projector Web Control (continued)

3.1.2 Network Information

Displays the projector’s current network conﬁguration settings.

Item Description

3. Web Control

Common Information

Projector Name Displays the projector name settings.

Wireless Information Displays the current settings of wireless LAN.

Mode Displays the mode of wireless LAN communication. DHCP Displays the DHCP setting. IP Address Displays the IP address. Subnet Mask Displays the subnet mask. Default Gateway Displays the default gateway. DNS Server Address Displays the DNS server address. MAC Address Displays the MAC address. Ch Displays the channel used for wireless LAN. Encryption Displays the data encryption setting. SSID Displays the SSID used by the projector. Speed Displays the current wireless LAN transmission speed.

Wired Information Displays the current wired LAN settings.

DHCP Displays the DHCP setting.

Displays information common to both wireless and wired LAN.

IP Address Displays the IP address. Subnet Mask Displays the subnet mask. Default Gateway Displays the default gateway. DNS Server Address Displays the DNS server address. MAC Address Displays the MAC address.

Page 40

3. Web Control

3.1 Projector Web Control (continued)

3.1.3 Network Settings

Displays and conﬁgures network settings.

Item Description

Common Setup

Projector Name

sysLocation (SNMP)

sysContact (SNMP)

AMX D.D. (AMX Device Discovery)

Conﬁgures the settings common to wireless and wired LAN. Conﬁgures the name of the projector.

The length of the Projector Name can be up to 64

alphanumeric characters. Only alphabets, numbers and following symbols can be used.

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ and space. Particular projector name is pre-assigned by default.

Conﬁgures the location to be referred to when using SNMP. The length of the sysLocation can be up to 255 alphanumeric

characters.

be used.

Conﬁgures the contact information to be referred to when using SNMP. The length of the sysContact can be up to 255 alphanumeric

characters.

be used.

Conﬁgures the AMX Device Discovery setting to detect the projector from the controllers of AMX connected to the same network. For the details of AMX Device Discovery, visit the AMX web site.

URL: http://www.amx.com

Only numbers ‘0-9’, alphabet ‘a-z’ and ‘A-Z’ can

(continued on next page)

Page 41

3.1 Projector Web Control - Network Settings (continued)

Item Description

Wireless Setup Conﬁgures the wireless LAN settings.

Mode Select "Ad Hoc" or "Infrastructure".

,3&RQ¿JXUDWLRQ Conﬁgures network settings.

DHCP ON Enables DHCP. DHCP OFF Disables DHCP.

IP Address Conﬁgures the IP address when DHCP is disabled. Subnet Mask Conﬁgures the subnet mask when DHCP is disabled.

3. Web Control

Default Gateway

DNS Server Address Conﬁgures the DNS server address.

Encryption Lock

Conﬁgures the default gateway when DHCP is disabled.

Select from “1” to “11”, a channel to use in the Ad Hoc mode.

NOTE

country. In addition, depending on the country or region,

it may be required to use a wireless network card that conforms to the standards in the respective country or

region.

Permits or inhibits changes of the following settings related to

wireless connection.

Mode

䡡㻌

Encryption

䡡㻌

Encryption key (WEP key, WPA passphrase)

䡡㻌

SSID

䡡㻌

When Encryption Lock is set to ON, these settings cannot be

changed by the menu of the projector.

NOTE

performed only when it can be connected without changing the current settings.

• The channels may vary depending on the

• If Encryption Lock is ON, wireless connection is

Encryption Select data encryption method.

(continued on next page)

Page 42

3. Web Control

3.1 Projector Web Control - Network Settings (continued)

Item Description

Wireless Setup Conﬁgures the wireless LAN settings.

Input the WEP key. Either ASCII characters or hexadecimal numbers can be used during WEP key input. However, you cannot use a combination of both.The length of the key is deﬁned as

WEP Key

WPA Passphrase

SSID

follows according to the WEP and character formats.

Encryption ASCII characters HEX numbers WEP 64bit 5 characters 10 characters

WEP 128bit 13 characters 26 characters

Input WPA Passphrase.

Available number of input characters is 8 to 63. Only

alphabets, numbers and the following symbols can be used.

!"#$%&'()*+,-./:;<=>?@ [\]^_`{|}~ and space

Select an SSID from the list. If you require to set your unique SSID, select [Custom], then

set your own SSID following the rules below.

The maximum number of input characters is 32. Only alphabets, numbers and the following symbols can be used.

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ and space.

(continued on next page)

Page 43

3.1 Projector Web Control - Network Settings (continued)

Item Description

Wired Setup Conﬁgures the wired LAN settings.

,3&RQ¿JXUDWLRQ Conﬁgures network settings.

DHCP ON Enables DHCP. DHCP OFF Disables DHCP.

IP Address Conﬁgures the IP address when DHCP is disabled. Subnet Mask Conﬁgures the subnet mask when DHCP is disabled.

3. Web Control

Default Gateway

DNS Server Address Conﬁgures the DNS server address.

Other Setup Conﬁgures other network settings.

Crestron e-Control

Conﬁgures the default gateway when DHCP is disabled.

Set whether or not to use Crestron e-Control If you choose Disable, not the selection window but the Login window of Projector Web Control will be displayed at ﬁrst.

Click the [Apply] button to save the settings.

NOTE

• The new conﬁguration settings are activated after restarting the network connection. When the conﬁguration settings are changed, you must restart the network connection. You can restart the network connection from

Network Restart on the main menu. (

63)

• If you connect the projector to an existing network, consult a network administrator before setting server addresses.

• The WEP Key, WPA passphrase and SSID settings will not be set if the invalid

characters are used.

• The projector does not allow both wireless and wired LAN to be connected to the same network. Do not set the same network address for both wireless and wired LAN.

Page 44

3. Web Control

3.1 Projector Web Control (continued)

3.1.4 Port Settings

Displays and conﬁgures communication port

settings.

Item Description

Network Control Port1 (Port:23)

Conﬁgures command control port 1 (Port:23).

Port open Click the [Enable] check box to use port 23. Authentication

Network Control Port2 (Port:9715)

Click the [Enable] check box when authentication is required

for this port.

Conﬁgures command control port 2 (Port:9715).

Port open Click the [Enable] check box to use port 9715. Authentication

PJLink

Port

(Port:4352)

Click the [Enable] check box when authentication is required

for this port.

Conﬁgures the PJLink

port (Port:4352).

Port open Click the [Enable] check box to use port 4352. Authentication

My Image Port (Port:9716)

Click the [Enable] check box when authentication is required

for this port.

Conﬁgures the My Image Port (Port:9716).

Port open Click the [Enable] check box to use port 9716. Authentication

Messenger Port (Port:9719)

Click the [Enable] check box when authentication is required

for this port.

Conﬁgures the Messenger Port (Port:9719).

Port open Click the [Enable] check box to use port 9719. Authentication

Click the [Enable] check box when authentication is required

for this port.

(continued on next page)

Page 45

3.1 Projector Web Control - Port Settings (continued)

Item Description

SNMP Port Conﬁgures the mib ﬁle port.

Port open Click the [Enable] check box to use SNMP.

Conﬁgures the destination of the SNMP Trap in IP format.

• The address allows not only IP address but also domain

Trap address

'RZQORDG0,%¿OH Downloads a MIB ﬁle from the projector.

Network Bridge Port Conﬁgures the Bridge port number.

Port number

name if the valid DNS server is setup in the Network Settings. The maximum length of host or domain name is up

to 255 characters.

Input the port number. Except for 41794, 9715, 9716, 9719, 9720, 5900, 5500, 4352 between 1024 and 65535 can be set up. It is set to 9717 as the default setting.

3. Web Control

Click the [Apply] button to save the settings.

NOTE

Network Restart on the main menu. (

63)

Page 46

3. Web Control

3.1 Projector Web Control (continued)

3.1.5 Mail Settings

Displays and conﬁgures e-mail addressing

settings.

Item Description

Click the [Enable] check box to use the e-mail function.

Send Mail

Conﬁgure the conditions for sending e-mail under the Alert Settings.

Conﬁgures the address of the mail server in IP format.

• The address allows not only IP address but also domain

SMTP Server Address

Sender E-mail address

Recipient E-mail address

Send Test Mail Sends a test e-mail to the set address.

name if the valid DNS server is setup in the Network Settings. The maximum length of host or domain name is up

to 255 characters.

Conﬁgures the sender e-mail address. The length of the sender e-mail address can be up to 255

alphanumeric characters.

Conﬁgures the e-mail address of up to ﬁve recipients. You

can also specify the [to] or [cc] for each address. The

length of the recipient e-mail address can be up to 255

alphanumeric characters.

Click the [Apply] button to save the settings.

Mail settings are initialized when clicking the [Reset] button.

NOTE

• You can conﬁrm whether the mail settings work correctly by using the

[Send Test Mail] button. Enable Send Mail setting before clicking the [Send Test Mail].

• If you connect the projector to an existing network, consult a network administrator before setting server addresses.

Page 47

3. Web Control

3.1 Projector Web Control (continued)

3.1.6 Alert Settings

Displays and conﬁgures failure & alert settings.

Notiﬁcation such as e-mail and SNMP trap can be set regarding the following errors/warnings.

䚷䡡Cover Error

䚷䡡Fan Error

䚷䡡Lamp Error

䚷䡡Temp Error

䚷䡡Air Flow Error 䚷䡡Cold Error

䚷䡡Filter Error

䚷䡡Shutter Error 䚷䡡Lens Shift Error 䚷䡡Color Wheel Error 䚷䡡Humidity Error

䚷䡡Other Error

䚷䡡Schedule Execution Error 䚷䡡Lamp Time Alarm 䚷䡡Filter Time Alarm 䚷䡡Filter Status Notiﬁcation 䚷䡡Cold Start 䚷䡡Authentication Failure

Refer to Chapter 8-1 for the details of the above errors/warnings. 㻔



87㻕

Page 48

3. Web Control

3.1 Projector Web Control - Alert Settings (continued)

The Alert Items are shown below.

Item Description Alarm Time SNMP Trap Click the [Enable] check box to enable SNMP Trap alerts. Send Mail

Mail Subject

Mail Text

Conﬁgures the time to alert.

(Only Lamp Time Alarm and Filter Time Alarm.)

Click the [Enable] check box to enable e-mail alerts.

(Except Cold Start and Authentication Failure.)

Conﬁgures the subject line of the e-mail to be sent.

The length of the subject line can be up to 100 alphanumeric

characters. Using any other character may shorten the

subject line. (Except Cold Start and Authentication Failure.)

Conﬁgures the text of the e-mail to be sent.

The length of the text is up to 1024 alphanumeric characters.

Using any other character may shorten the text.

(Except Cold Start and Authentication Failure.)

Click the [Apply] button to save the settings.

The settings are initialized when clicking the [Reset] button.

Page 49

3.1 Projector Web Control (continued)

3.1.7 Schedule Settings

Displays and conﬁgures schedule settings.

3. Web Control

1) Schedule Management

Item Description Sunday Monday Tuesday Wednesday Thursday Friday Saturday

NOTE

before enabling scheduled events. (

• Be sure to set the date and time



Date/Time Settings)

• Refer to 8.3 Event Scheduling for the details

of schedule settings. (

Schedule settings executed on each day of the week.



92)

3.1.8

6SHFL¿FGDWH1R

6SHFL¿FGDWH1R

6SHFL¿FGDWH1R

6SHFL¿FGDWH1R

6SHFL¿FGDWH1R

Schedule settings executed on speciﬁed day. Up to 5 days can be speciﬁed.

Page 50

3. Web Control

3.1 Projector Web Control - Schedule Settings (continued)

Item Description Schedule

Program

Date (Month/Day)

Select the checkbox of the schedule to execute.

Select the program. The detail of the event registered in each program can be conﬁrmed in the program list displayed at

the bottom of the screen.

Input the date (month/day) when the schedule is executed for Speciﬁc date 1~5.

Click the [Apply] button to save the settings.

Click the [Refresh] button to update the screen to the latest status. Click the [Program Edit] button to display the program edit of the selected program. Click the [Copy to] button to copy the content of the program from which you copy

(the list on the left) to the program to which you copy (the list on the right). The same program No. cannot be selected for both the program from which and the program to which you copy.

Page 51

3. Web Control

3.1 Projector Web Control - Schedule Settings (continued)

2) Program Edit

The current event settings are displayed on the list. To add additional functions and events, set the following items.

NOTE

• A maximum of 16 programs of schedule can be set. A maximum of

20 events can be registered in 1 program.

CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411

Item Description Time Conﬁgures the time to execute events. Event [Parameter] Conﬁgures the events to be executed.

Power

CP-HD9320/HD9321

Input Source

COMPUTER IN1

(CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411)

COMPUTER IN2

(CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411)

COMPUTER IN

(CP-HD9320/HD9321)

HDMI 1 HDMI 2 DVI-D HDBaseT SDI/DIGITAL 1

(CP-HD9320/HD9321)

Conﬁgures the parameters for power control.STANDBY

Conﬁgures the parameters for switching input.

VIDEO LAN

Page 52

3. Web Control

3.1 Projector Web Control - Schedule Settings (continued)

Item Description

My Image

IMAGE-OFF IMAGE-1 IMAGE-2 IMAGE-3 IMAGE-4

Messenger

TEXT-OFF TEXT-1 TEXT-2 TEXT-3 TEXT-4 TEXT-5 TEXT-6 TEXT-7 TEXT-8 TEXT-9 TEXT-10

Conﬁgures the parameters for My Image data display.

Conﬁgures the parameters for Messenger data display.

TEXT-11 TEXT-12

Eco Mode

Conﬁgures the parameters for eco mode switching.NORMAL

ECO

Blank

Conﬁgures the parameters for blank screen on/off control.OFF

Click the [Register] button to add new events to the program. Click the [Delete] button to delete events from the program. Click the [Delete All] button to clear all the events registered in the current

selected program.

Click the [Back] button to go back to the schedule management screen.

Page 53

3. Web Control

3.1 Projector Web Control (continued)

3.1.8 Date/Time Settings

Displays and conﬁgures the date and time

settings.

Item Description

Current Date Conﬁgures the current date in year/month/day format. Current Time Conﬁgures the current time in hour:minute:second format.

Daylight Savings Time

Start Conﬁgures the date and time daylight savings time begins.

Month Conﬁgures the month daylight savings time begins (1~12). Week

Day

hour Conﬁgures the hour daylight savings time begins (0 ~ 23).

Time

minute Conﬁgures the minute daylight savings time begins (0 ~ 59).

End Conﬁgures the date and time daylight savings time ends.

Month Conﬁgures the month daylight savings time ends (1 ~ 12). Week

Day

hour Conﬁgures the hour daylight savings time ends (0 ~ 23).

Time

minute Conﬁgures the minute daylight savings time ends (0 ~ 59).

Click the [ON] check box to enable daylight savings time and

set the following items.

Conﬁgures the week of the month daylight savings time begins (First, 2, 3, 4, Last).

Conﬁgures the day of the week daylight savings time begins (Sun, Mon, Tue, Wed, Thu, Fri, Sat).

Conﬁgures the week of the month daylight savings time ends (First, 2, 3, 4, Last).

Conﬁgures the day of the week daylight savings time ends (Sun, Mon, Tue, Wed, Thu, Fri, Sat).

(continued on next page)

Page 54

3. Web Control

3.1 Projector Web Control - Date/Time Settings (continued)

Item Description

Conﬁgures the time difference. Set the same time difference

Time difference

SNTP Server Address

SNTP

as the one set on your computer. If unsure, consult your IT manager.

Conﬁgures the SNTP server address in IP format.

• The address allows not only IP address but also domain

name if the valid DNS server is setup in the Network

Settings. The maximum length of host or domain name is up to 255 characters.

Cycle

Conﬁgures the interval at which to retrieve Date and Time

information from the SNTP server (hour:minute).

Click the [Apply] button to save the settings.

NOTE

Network Restart on the main menu. (

63)

• If you connect the projector to an existing network, consult a network administrator before setting server addresses.

• To enable the SNTP function, the time difference must be set.

• The projector will retrieve Date and Time information from the time server and override time settings when SNTP is enabled.

•

The internal clock’s time may not remain accurate. Using SNTP is recommended

to maintain accurate time.

• The internal battery is required to be replaced when the time is off soon after

setting date and time.

Page 55

3.1 Projector Web Control (continued)

3.1.9 Security Settings

Displays and conﬁgures passwords and other

security settings.

Item Description

User Account Conﬁgures the user name and password.

Conﬁgures the user name.

User name

The length of the text can be up to 32 alphanumeric characters.

3. Web Control

Conﬁgures the password.

Password

Re-enter Password Reenter the above password for veriﬁcation.

Network Control

Authentication Password

Re-enter Authentication Password

SNMP Conﬁgures the community name if SNMP is used.

Community name

The length of the text can be up to 255 alphanumeric characters.

Conﬁgures the Authentication password for Network Control Port1 (Port: 23), Network Control Port2 (Port: 9715), PJLink™ Port (Port: 4352), My Image Port (Port: 9716), and Messenger Port (Port: 9719). (

Conﬁgures the Authentication password.

The length of the text can be up to 32 alphanumeric characters.

Reenter the above password for veriﬁcation.

Conﬁgures the community name. The length of the text can

be up to 64 alphanumeric characters.

44)

Click the [Apply] button to save the settings.

NOTE

Network Restart on the main menu. (

63)

• Only numbers ‘0-9’, alphabet ‘a-z’ and ‘A-Z’ can be used.

Page 56

3. Web Control

3.1 Projector Web Control (continued)

3.1.10 Projector Control

Operations of the projector can be performed with the items on the screen. The categories of the items are shown in the main menu.

Most of the items have

a submenu. Refer to the table below for details.

NOTE

CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411

• The setting value may not match with the actual value if the user

CP-HD9320/HD9321

changes the value manually. In that case, refresh the page by clicking the

[Refresh] button.

Page 57

3.1 Projector Web Control - Projector Control (continued)

Item

POWER INPUT SOURCE BLANK ON/OFF FREEZE MAGNIFY MAGNIFY POSITION V MAGNIFY POSITION H TEMPLATE SHUTTER

[ON]: closed / [OFF]: opened ZOOM

/ : Turns the lens to the upper or lower limit of its movable range. : Stops turning the lens. / / / : Fine adjustment in two steps is available.

MAIN

FOCUS

/ : Turns the lens to the upper or lower limit of its movable range. : Stops turning the lens. / / / : Fine adjustment in two steps is available.

3. Web Control

LENS SHIFT V LENS SHIFT H

/ : Turns the lens to the upper or lower limit of its movable range. : Stops turning the lens. / / / :

LENS MEMORY WINDOW CONFIGURATION - OFF / PbyP / PinP

Click the [Apply] button to execute after selecting the display mode (OFF/ PbyP/ PinP) from the dropdown list. Click the [Edit] button to display the screen for detailed settings while PbyP or PinP display mode.

MY IMAGE MY IMAGE DELETE

(continued on next page)

Vertical and horizontal ﬁne adjustment in two steps is available.

Page 58

3. Web Control

3.1 Projector Web Control - Projector Control (continued)

Item

PICTURE MODE

PICTURE

IMAGE

PICTURE QUALITY

GAMMA COLOR TEMP

ACCENTUALIZER BRIGHTNESS CONTRAST COLOR TINT SHARPNESS HDCR COLOR WHEEL ACTIVE IRIS MYMEMORY ASPECT

The selected parameter cannot be set depending on the input signal. OVER SCAN V POSITION H POSITION H PHASE H SIZE AUTO ADJUST EXECUTE PROGRESSIVE VIDEO NR COLOR SPACE VIDEO FORMAT

INPUT

DIGITAL FORMAT DIGITAL RANGE COMPUTER IN FRAME LOCK

(continued on next page)

Page 59

3.1 Projector Web Control - Projector Control (continued)

Item

3. Web Control

SETUP

KEYSTONE PERFECT FIT SETUP

EDGE BLENDING

WARPING MODE

LAMP & FILTER

INSTALLATION STANDBY MODE

NOTE

• The network function is not available when STANDBY

KEYSTONE V

KEYSTONE H

BLENDING LEVEL

SETUP

CROPPING

ECO MODE

LAMP MODE

ALTERNATE

CYCLE TIME

FILTER MESSAGE

MODE is set to SAVING and the projector is in standby mode. Connect the projector to the network after setting STANDBY MODE to NORMAL.

MONITOR OUT LANGUAGE

Click the [Apply] button to switch the language on the Web screen according

to the setting of the selected language in the projector.

MENU POSITION V MENU POSITION H

BLANK AUTO BLANK

SCREEN

(continued on next page)

START UP MyScreen Lock OSD MESSAGE TEMPLATE C.C. - DISPLAY C.C. - MODE C.C. - CHANNEL

Page 60

3. Web Control

3.1 Projector Web Control - Projector Control (continued)

Item

SOURCE SKIP AUTO SEARCH DIRECT POWER ON AUTO POWER OFF

OPTION

SERVICE

(continued on next page)

SHUTTER TIMER MY BUTTON – 1 / 2 / 3 / 4 REMOTE RECEIV. REMOTE FREQ. REMOTE ID Quit Presenter Mode

Quit compulsorily from the Presenter mode. Refer to Chapter 4 for the details of Presenter Mode.

㻌㻔

75

㻕

Page 61

3. Web Control

3.1 Projector Web Control (continued)

3.1.11 Remote Control

The functions on the bundled remote control are assigned to the Web Remote

Control screen. Do not control the projector with the projector's remote control and via Control

at the same time. It may cause some operational errors in the projector.

Web Remote

CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411



STANDBY

ON COMPUTER IN1 COMPUTER IN2 (

COMPUTER IN (



CP-X9110/WX9210/WU9410/X9111/WX9211/WU9411

(

CP-X9110/WX9210/WU9410/X9111/WX9211/WU9411

CP-HD9320/HD9321

HDMI 1 HDMI 2 DVI-D HDBaseT SDI/DIGITAL 1 (

CP-HD9320/HD9321

VIDEO LAN BLANK FREEZE SHUTTER

ŸźŻŹ

ENTER MENU RESET

CP-HD9320/HD9321

) )

)

NOTE

• One operation can be executed only with one click. The button should

be clicked repeatedly to operate continuously.

• When clicking the button repeatedly, some commands may not be sent

correctly. Click it at intervals.

•

When the [STANDBY] or [ON] button is pushed, a message window comes up to

conﬁrm the operation. To control the power, push [OK], otherwise push [Cancel].

Page 62

3. Web Control

3.1 Projector Web Control (continued)

3.1.12 Projector Status

Displays the current settings and status of the projector.

CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411

Item Description Error Status Displays the error status. Lamp-1 Time Displays the usage time for the lamp-1. Lamp-2 Time Displays the usage time for the lamp-2. Filter Time Displays the usage time for the ﬁlter.

CP-HD9320/HD9321

Filter Status Displays the cleanliness level of the air ﬁlter. Power Status Displays the power status. Input Status Displays the input signal source. Blank On/Off Displays the BLANK screen on/off status. Freeze Displays the Freeze status. Shutter Displays the Shutter status.

Page 63

3.1 Projector Web Control (continued)

3.1.13 Network Restart

Restarts the projector’s network connection.

Item Description

3. Web Control

Restart

NOTE

• Restarting requires you to re-login in order to further control or

Restarts the projector’s network connection in order to

activate new conﬁguration settings.

conﬁgure the projector via a web browser. Wait 30 seconds or more after

clicking the [Restart] button to log on again.

Page 64

3. Web Control

3.1 Projector Web Control (continued)

3.1.14 Connection Test

Checks if the network is connecting to DNS server or SNTP server, etc.

Item Description Destination IP Address

Click the [Execute] button to test the connection after entering IP address to connect to.

Display example of the connection succeeded 䠖

Display example of the connection failed 䠖

•

NOTE

Conﬁrm information of the target IP address with network administrator.

• Connection test may result in an error even if the connection is performed

properly when the packets for checking the connection are discarded before

arriving at the target depending on the settings of ﬁrewall or packet ﬁltering, etc.

• The result of the connection test is displayed only in English.

Page 65

3. Web Control

3.2 Crestron e-Control

CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411

Tab

The Main window as shown above is displayed at ﬁrst. However, if you have enabled User Password on the Tools window (

69), a dialog prompting you to

enter the password as shown on the right will be displayed, and no operation is

enabled until you have entered the password. After entering the preset password, the dialog disappears and the Main window will be displayed. As shown below, you can open a window by clicking the corresponding tab at the

top right of the window.

CP-HD9320/HD9321

CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411

User Password dialog

Tab Description

Logs out from e-Control

Logout

Tools Opens Tools window. (

This tab appears only when User Password of the Tools window is

enabled.

69)

CP-HD9320/HD9321

User Password dialog

Info Opens Info window. ( Contact IT Help Opens Help Desk window. (

71)

72)

Page 66

3. Web Control

3.2 Crestron e-Control

(continued)

NOTE

Disable, Crestron e-Control Crestron e-Control

• If Crestron e-Control® in the Network Settings (43) is set to

cannot be used to operate the projector. Enable

and close the web browser. Next, restart the web browser,

followed by entering the projector's IP address.

• Only English is supported on Crestron e-Control

• If the connection is terminated, the "Loading..." screen will appear. Check the

connection between the projector and the computer, then return or refresh the Web page.

• The control from Crestron e-Control

is supported only via wired LAN.

Page 67

3.2 Crestron e-Control® (continued)

3.2.1 Main window

3. Web Control

CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411

1 4

CP-HD9320/HD9321

You can operate the basic controls of the projector on this screen.

NOTE

• If the projector is in the standby mode, only the [Power] button can

be operated.

Click a button and operate as follows.

Button Description

1 4

Power Turns the power on/off.

2. Sources List

You can click a button to switch the input channel. The cursor will move

according to the currently selected input port.

Button Description

Computer in1

(CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411)

Computer in2

(CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411)

Computer In

(CP-HD9320/HD9321)

HDMI 1 Selects input from HDMI 1 port. HDMI 2 Selects input from HDMI 2 port. DVI-D Selects input from DVI-D port. HDBaseT Selects input from HDBaseT port. SDI/DIGITAL 1

(CP-HD9320/HD9321)

Selects input from COMPUTER IN1 port.

Selects input from COMPUTER IN2 port.

Selects input from COMPUTER IN port.

Selects input from SDI/DIGITAL 1 port.

Video Selects input from VIDEO port. LAN Selects input from LAN port.

Page 68

3. Web Control

3.2 Crestron e-Control® - Main window (continued)

3. Click a button and operate as follows. To show the hidden buttons, click the ◄ / ► icons at the left and right ends.

Button Description

Freeze Turns Freeze on/off. Contrast Adjusts the contrast setting. Brightness Adjusts the brightness setting. Color Adjusts the color setting. Sharpness Adjusts the sharpness setting.

Controls the magniﬁcation setting using the [+] / [-] buttons.

Magnify

Auto Performs the automatic adjustment. Blank Turns the BLANK screen on/off.

Use the [▲] [▼] [◄] [►] buttons to move to the area you want

to magnify.

4. Click the button and operate in the same way as the bundled remote control.

Button Description

Menu Enter Assigned the same operation as ENTER button. Reset Assigned the same operation as RESET button.

Ÿ Assigned the same operation as Ÿ button.

▼ Assigned the same operation as ▼ button. ◄ Assigned the same operation as ◄ button. ► Assigned the same operation as ► button.

Assigned the same operation as MENU button.

Page 69

3.2 Crestron e-Control® (continued)

3.2.2 Tools window

3. Web Control

Conﬁgures the settings

between the projector and Crestron

Click the [Exit] button to return to the Main window.

NOTE

• If two-byte characters are used, the input text or numbers cannot be

set correctly.

• Any items on this window cannot be left blank.

1. Crestron Control

Conﬁgures the settings of Crestron

control system devices.

control system.

Item Description

IP Address Conﬁgures the IP address of the control system. IP ID Conﬁgures the IP ID of the control system.

Port

Speciﬁes the port number used for communication by the

control system.

To apply the settings, click the [Send] button.

2. Projector

Conﬁgures the network settings of the projector.

Item Description

Projector Name

Location

Assigned To:

Conﬁgures the name of the projector. The length of the Projector Name can be up to 64 alphanumeric characters.

Conﬁgures the location name of the projector. You can specify a Location name up to 32 alphanumeric characters.

Conﬁgures the user name for the projector. You can specify a

user name up to 32 alphanumeric characters.

The usable symbols are space and the following:

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~

To apply the settings, click the [Send] button.

Page 70

3. Web Control

3.2 Crestron e-Control® - Tools window (continued)

3. Projector (continued)

Conﬁgures the network settings of the projector.

Item Description DHCP Enables DHCP. IP Address Conﬁgures the IP address when DHCP is disabled. Subnet Mask Conﬁgures the subnet mask when DHCP is disabled. Default Gateway Conﬁgures the default gateway when DHCP is disabled. DNS Server Conﬁgures the DNS server address when DHCP is disabled.

To apply the settings, click the [Send] button.

4. User Password

Conﬁgures the User Password. To prompt the entry of User Password before starting e-Control

, select the checkbox.

Item Description

Conﬁgures the password.

New Password

&RQ¿UP

You can specify a password up to 26 alphanumeric characters.

The usable symbols are space and the following:

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ Reenter the above password for veriﬁcation. If the password is

incorrect, an error message is displayed.

To apply the settings, click the [Send] button.

5. Admin Password

Conﬁgures the Admin Password. To prompt the entry of Admin Password before

displaying the Tools window, select the checkbox.

Item Description

Conﬁgures the password.

New Password

&RQ¿UP

You can specify a password up to 26 alphanumeric characters.

The usable symbols are space and the following:

!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~ Reenter the above password for veriﬁcation. If the password is

incorrect, an error message is displayed.

To apply the settings, click the [Send] button.

Page 71

3.2 Crestron e-Control® (continued)

3.2.3 Info window

3. Web Control

CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411

CP-HD9320/HD9321

Displays the current settings and status of the projector.

Click the [Exit] button to return to the Main window.

1. Projector Information

Item Description Projector Name Displays the projector name settings.

Location Displays the location name of the projector. MAC Address Displays the wired LAN MAC address of the projector.

Resolution Lamp-1 Hours Displays the usage time for the lamp-1.

Lamp-2 Hours Displays the usage time for the lamp-2. Assigned To: Displays the user name for the projector.

Displays the resolution and vertical frequency of the signal input

selected on the projector.

2. Projector Status

Item Description Power Status Displays the power status. Input Source Displays the input signal source. Picture Mode Displays the picture mode setting. Installation Displays the installation setting. Eco Mode Displays the eco mode setting. Error Status Displays the error status.

NOTE

• Projector Name, Location and the user name for Assigned To: may

appear truncated if they are too long.

Page 72

3. Web Control

3.2 Crestron e-Control® (continued)

3.2.4 Help Desk window

CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411

CP-HD9320/HD9321

Sends/receives messages to/from the administrator for Crestron RoomView

Express and Fusion RV

Button Description

Send Sends a message.

Checks the received message.

Page 73

3.2 Crestron e-Control® (continued)

3.2.5 Emergency Alert

3. Web Control

CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411

When the administrator for Crestron RoomView

CP-HD9320/HD9321

Express and Fusion RV® sends

out an alert message, it will be displayed on the screen.

You can reply to the alert message via a chat format.

below the alert message,

NOTE

RoomView

• For details of Emergency Alert, refer to the manual of Crestron

Express or Fusion RV®.

• The alert message from Crestron RoomView

and click the [Send] button.

and Fusion RV® is displayed

Input a message in the box

on the screen of the projector in the way similar to the real-time text of the Messenger function. (

80) If another real-time text is displayed on the screen,

it will be overwritten by the alert message. However, if the priority of the real-

time text is set to high, the alert message does not appear on the screen. For

details, refer to the manual for the application of the Messenger.

Page 74

4. Network Presentation

4.1 Outline

The projector can display the computer screen images transmitted through the

network. This Network Presentation feature helps you to smoothly make your

presentations and conduct conferences.

To use Network Presentation, an exclusive application, "LiveViewer" is required.

It can be installed from the bundled application CD.

For details of Network Presentation and instructions to install the "LiveViewer", refer to the manual for "LiveViewer".

NOTE

•㻌The use of "LiveViewer" function depends on the model you are using. If you want to use the latest "LiveViewer", please refer to the appropriate group item in the "LiveViewer" User's Manual. This model will be in the Group of G.

• For Mac user, download the software from the website. Refer to 2-5. Applications.

Page 75

4. Network Presentation

4.2 Display Mode

LiveViewer has two display modes, Single PC mode and Multi PC mode.

4.2.1 Single PC mode

The Single PC mode can display images in full screen from one computer to the projector/switcher via wireless LAN or wired LAN.

■ Presenter Mode In the Single PC mode, the projector can be occupied by one computer and can block access from any other computers (if Presenter Mode is set to ON in LiveViewer). While making your presentation, you don’t need to worry that the

image on screen will be unexpectedly switched to an image sent by another

computer. Presenter Mode can be set to ON in the option menu in the LiveViewer.

4.2.2 Multi PC mode

The projector can display images of up to four computers connected at the same time.

Page 76

4. Network Presentation

4.3 Multi Projector Mode

In the Multi Projector/Multi Display mode, up to 12 projectors or switchers connected to projectors can connect with the computer via wireless or wired LAN

simultaneously.

This function is for Windows users only.

4.4 Moderator Control Mode

One computer can be assigned as Moderator (Host) to control all other computers (Clients) or the switchers connected with the projector via wireless LAN or wired LAN. Since Clients cannot control the LiveViewer and the projector, the Host can

proceed with the program as arranged smoothly and safely.

Moderator (Host)

LAN

This function is for Windows users only.

Clients

Page 77

4. Network Presentation

4.5 Port Number

The port numbers used for LiveViewer are shown below.

Port No. Protocol

5500 TCP 5900 TCP 9720 TCP

NOTE

• When other application uses the ports above, LiveViewer and Projector Quick Connection may not work.

Page 78

5. MyImage Function

5. My Image Function

The projector can display still images transferred via the network. It is possible to allocate up to 4 image ﬁles.

MY IMAGE transmission requires an exclusive application for your computer. Use the application to transfer the image data. The image transferred via the network can also be registered as MyScreen of the

projector. For information on the necessary settings and operations for the computer and

projector, refer to the manual for the application.

To display the transferred image, select the MY IMAGE item in the NETWORK menu. For more information, please see the description of the MY IMAGE item of

the NETWORK menu.

Page 79

5. MyImage Function

NOTE

image. (

• Using MY BUTTON registered as MY IMAGE can display transferred

OPTION menu in the Operating Guide)

• The image ﬁle also can be displayed by using schedule function from the web browser. Refer to item 8.3 Event Scheduling (

•

If data is transferred via wireless and wired LAN at the same time, the projector

may not be able to process the data correctly

92) in detail.

Page 80

6. Messenger Function

6.1 Outline

The projector can display text data transferred via the network on the screen.

The text data can be displayed on the screen in two ways. One is to display the text transferred from the computer on real time, and the other is to choose the text data stored in the projector and display it. It is possible to store up to 12 text data.

Transfer text data

Display text data (ex.

)

Page 81

6. Messenger Function

Messenger function requires an exclusive application for your computer. To edit,

transfer and display the text data, use the application. For information on the necessary settings and operations for the computer and

projector, refer to the manual for the application.

6.2 Supported Languages

The languages that can be displayed by Messenger function are shown below.

English, French, German, Spanish, Italian, Norwegian, Dutch, Portuguese, Swedish, Finnish, Danish, Brasileiro, Indonesian, Lithuanian, Estonian, Latvian, Polish, Czech, Hungarian, Slovenian, Croatian, Russian, Turkish, Greek, Japanese, Simpliﬁed Chinese, Traditional Chinese, Korean, Vietnamese

6.3 Display Style

There are 4 types of message display style. The following is the description of each type.

1) Scroll

The message scrolls to the left in the message

Toda

’s

The chemical class

display area.

2) Box (Scroll up) The message scrolls upwards in the square

message display area.

Page 82

6. Messenger Function

3) Pop on The message is displayed in full view in the square message display area.

4) Picture Side

The message is displayed in the message display area on the right or left.

This style is available only for WXGA, WUXGA, and HD model projector.

NOTE

displaying messenger text on/off. (

• Using MY BUTTONS registered as MESSENGER can turn the

OPTION menu in the Operating Guide)

• The text ﬁle also can be displayed by using schedule function via the web

browser. Refer to item 8.3 Event Scheduling (

•

If data is transferred via wireless and wired LAN at the same time, the projector

92) for the detail.

may not process the data correctly.

Page 83

7. Network Bridge Function

This projector is equipped with the NETWORK BRIDGE function to perform mutual conversion of a network protocol and a serial interface. By making use of the NETWORK BRIDGE function, a computer connected to the projector via wireless or wired LAN is able to control an external device via RS232C communication using the projector as a network terminal.

Protocol change

RS-232C

RS-232C cable

External device

WIRELESS port

(USB wireless adapter)

LAN port

Computer

CONTROL port

TCP/IP data Serial data

Wired LAN

LAN cable

Wireless

LAN

7.1 Connecting devices

1) Connect the projector’s LAN port to the computer’s LAN port with a LAN cable,

or insert the USB wireless adapter into the WIRELESS port.

2) Connect the projector’s CONTROL port and the device’s RS-232C port with an

RS-232C cable, for RS-232C communication.

NOTE

to ensure the connection.

• Before connecting the devices, read the manuals for the devices

For RS-232C connection, check the speciﬁcations

of each port and use the suitable cable. ( Operating Guide - Technical)

Connection to the ports in the

Page 84

7. Network Bridge Function

7.2 Communication setup

To conﬁgure the setup of the communication using NETWORK BRIDGE for the projector, use items in the COMMUNICATION menu. Open the menu of the projector and select the OPTION - SERVICE - COMMUNICATION menu.

(

OPTION menu > SERVICE > COMMUNICATION in the Operating Guide)

1) In the COMMUNICATION TYPE menu, select NETWORK BRIDGE (WIRELESS or WIRED depending on the type of connection you use) for the

CONTROL port.

2) Using the SERIAL SETTINGS menu, select the proper baud rate and parity

for the CONTROL port, according to the speciﬁcation of the RS-232C port of

the connected device.

Item Condition

BAUD RATE 4800bps/9600bps/19200bps/38400bps

PARITY NONE/ODD/EVEN

Data length 8 bit (ﬁxed)

Start bit 1 bit (ﬁxed)

Stop bit 1 bit (ﬁxed)

3) Using the TRANSMISSION METHOD menu, set up the proper method for the

CONTROL port according to your use.

NOTE

• The OFF is selected for the COMMUNICATION TYPE as the default

setting.

• Using the COMMUNICATION menu, set up the communication. Remember

that an unsuitable setup could cause malfunction of communication.

• When either one of the NETWORK BRIDGE settings is selected in the COMMUNICATION TYPE menu, RS-232C commands cannot be received from

the CONTROL port.

7.3 Communication port

For the NETWORK BRIDGE function, send the data from the computer to the

projector with using the Network Bridge Port conﬁgured in the Port Settings of web browser. (

NOTE

• Except for 41794, 9715, 9716, 9719, 9720, 5900, 5500, 4352

44)

between 1024 and 65535 can be set up as the Network Bridge Port number. It is set to 9717 as the default setting.

Page 85

7. Network Bridge Function

7.4 Transmission method

The transmission method can be selected from the menus, only when the

NETWORK BRIDGE is selected for the COMMUNICATION TYPE.

OPTION menu > SERVICE > COMMUNICATION in the Operating Guide)

(

HALF-DUPLEX  FULL-DUPLEX

7.4.1 HALF-DUPLEX

This method lets the projector make two way communication, but only one

direction, either transmitting or receiving data, is allowed at a time. The method does not allow the projector to receive the data from the computer while waiting for response data from an external device. After the projector receives the response data from an external device or the response limit time is past, the projector can receive the data from the computer. That means that the projector controls transmitting and receiving the data to synchronize the communication.

To use the HALF-DUPLEX method, set up the RESPONSE LIMIT TIME following

the instructions below.

TCP/IP data Serial data

Wired LAN

LAN cable

Computer

Wireless LAN

Transmitting data

Discarding data

Protocol change

Response limit time

RS-232C

RS-232C cable

Transmitting data

Response data

External device

Response data

Discarding data

Using the RESPONSE LIMIT TIME menu, set the waiting time for response data

from an external device. (

OPTION menu > SERVICE > COMMUNICATION

in the Operating Guide)

OFF  1s  2s  3s ( OFF)

Page 86

7. Network Bridge Function

7.4 Transmission method (continued)

NOTE

• With using the HALF-DUPLEX method, the projector can send out

254 byte data at the maximum at a time.

• If it is not required to monitor the response data from an external device and the RESPONSE LIMIT TIME is set to OFF, the projector can receive the data from the computer and send it out to an external device continuously.

The OFF is selected as the default setting.

7.4.2 FULL-DUPLEX

This method lets the projector make two way communication, transmitting and

receiving data at the same time, without monitoring response data from an external device. With using this method, the computer and an external device will send the data out of synchronization. If it is required to synchronize them, set the computer to make the synchronization.

NOTE

When the computer controls the synchronization of receptions and transmissions,

• the external device may not be controlled properly depending on the status of data

processing of the projector.

Page 87

8. Other Functions

8.1 E-mail Alerts

The projector can automatically send an alert message to the speciﬁed e-mail addresses when the projector detects a certain condition that is requiring

maintenance or detected an error.

NOTE

• The projector may be not able to send e-mail if the projector suddenly loses

power.

• This function is not available if you use a mail server requiring authentication

to send a mail.

•

Mails may not be sent correctly depending on the mail environment you are

using.

Alerts available to E-mail alerts are as follows.

Cover Error The lamp cover has not been properly ﬁxed. Fan Error The cooling fan is not operating.

Lamp Error

• Up to ﬁve e-mail addresses can be speciﬁed.

Item Description

The lamp does not light, and there is a possibility that interior portion has become heated.

Temp Error Air Flow Error The internal temperature is rising. Cold Error Filter Error Filter time over.

Shutter Error The shutter does not work correctly. Lens Shift Error The Lens shift does not work correctly. Color Wheel Error The Color Wheel does not work correctly. Humidity Error The humidity is too high.

Other Error Schedule Execution

Error Lamp Time Alarm Lamp Time has exceeded the speciﬁed alarm limit. Filter Time Alarm Filter Time has exceeded the speciﬁed alarm limit.

There is a possibility that the interior portion has become heated.

There is a possibility that the interior portion has

become overcooled.

Errors other than the above.

If this error is displayed, please contact your dealer.

Failed to execute scheduled events.

(continued on next page)

Page 88

8. Other Functions

Item Description

Filter Status

1RWL¿FDWLRQ

NOTE

• The timing of receiving Filter Error e-mail is depending on the FILTER

The status to clean the air ﬁlter is changed.

MESSAGE setting in the LAMP & FILTER item of the SETUP menu which determines the period until the ﬁlter message is displayed on the projector screen. An e-mail will be sent when the usage time of the ﬁlter exceeds the set time limit. No notiﬁcation e-mail will be sent if the FILTER MESSAGE is set to TURN OFF. (

SETUP menu in the Operating Guide)

• Lamp Time Alarm is a threshold for e-mail notiﬁcation of the lamp time.

When the set time exceeds the limit conﬁgured in the Projector Web Control, an e-mail will be sent. Lamp Time Alarm can be enabled for both or either one of lamp-1 and lamp-2.

Filter Time Alarm is a threshold for e-mail notiﬁcation of the ﬁlter time. When

• the set time exceeds the limit conﬁgured in the Projector Web Control, an e-mail

will be sent.

• )LOWHU6WDWXV1RWL¿FDWLRQcan be enabled for both or either one of Status 1 and 2. These notiﬁcations are equivalent to the changing of the FILTER

indicator on the projector. (Status 1: off to orange, Status 2: orange to red) Refer to the Operating Guide for details of the FILTER indicator.

• Lamp Error e-mail is sent as follows:

- When both lamps are in failure, “Lamp Error” is sent.

When either one of lamps is in failure, “Lamp-1 Warning” or “Lamp-2 Warning”

is sent according to the failed lamp.

Page 89

8. Other Functions

To use the projector’s e-mail alert function, please conﬁgure the following items

through a web browser.

Mail Settings (

46)

1) Select [Mail Settings] on main menu in Projector Web Control.

2) Conﬁgure each item in Mail Settings page. Refer to item 3.1.5 Mail Settings

(

46) for further information.

3) Click the [Apply] button to save the settings.

4) Click the [Send Test Mail] button to conﬁrm that the e-mail settings are correct.

The following mail will be delivered to the speciﬁed addresses.

Subject line : Test Mail <Projector name> Text : Send Test Mail Date <Testing date> Time <Testing time> IP Address <Projector IP address> MAC Address <Projector MAC address>

Alert Settings (

47)

1) Select [Alert Settings] on main menu in Projector Web Control.

2) Select and conﬁgure each alert item. Refer to item 3.1.6 Alert Settings (

47)

for further information.

3) Click the [Apply] button to save the settings.

Failure/Warning e-mails are formatted as follows:

Subject line : <Mail title> <Projector name> Text : <Mail text> Date <Failure/Warning date> Time <Failure/Warning time> IP Address <Projector IP address> MAC Address <Projector MAC address>

Page 90

8. Other Functions

8.2 Projector Management using SNMP

The SNMP (Simple Network Management Protocol) enables to manage the

projector information, which is a failure or warning status, from the computer on the network.

NOTE

• It is recommended that SNMP functions are executed by a network

administrator.

• SNMP management software must be installed on the computer to monitor the projector via SNMP.

Standard MIB (MIB-2)

You can refer the following items deﬁned in system group of Standard MIB (MIB-2).

Item Description

sysName Projector name is set.

sysLocation The information on where it is located. It has character string

set in sysLocation (SNMP) in Projector Web Control - [Network Settings] - [Common Setup].

sysContact The information on the administrator's contact information. It

has character string set in sysContact (SNMP) in Projector Web Control - [Network Settings] - [Common Setup].

Enhanced MIB

You can get conﬁguration information by using Enhanced MIB for projectors. Enhanced MIB for projectors can be downloaded from [Port Settings] page in Projector Web Control.

Trap

When an error or warning occurs in the projector, a notiﬁcation can be sent to the speciﬁed address. In addition to e-mail alert shown in 8.1 Email Alerts (

87), the following

notiﬁcation can be sent.

Item Description

Cold Start When the projector is supplied with the power, it works as

below.

• If the STANDBY MODE is set to the NORMAL: the projector's power status changes from “OFF” to “Standby state”.

• If the STANDBY MODE is set to the SAVING: the projector's power status changes from “Standby state” to “ON (lamp is

turned on)”. (

SETUP menu in the Operating Guide).



Authentication Failure The SNMP access is detected from the invalid SNMP

community.

Page 91

8. Other Functions

Setup the following functions through WEB browser, if you want to manage the projector by SNMP.

Port Settings (

44)

1) Select [Port Settings] on main menu in Projector Web Control.

2) Click the >'RZQORDG0,%¿OH@ to download a MIB ﬁle.

3) Click the [Enable] check box to open the SNMP Port. Set the address to send

the SNMP trap to when a Failure/Warning occurs.

Security Settings (

55)

1) Select [Security Settings] on main menu in Projector Web Control.

2) Click the [SNMP] and set the community name on the screen that is displayed.

Alert Settings (

47)

Conﬁgure the settings for Trap transmission of Failures/Warnings.

1) Select [Alert Settings] on main menu in Projector Web Control.

2) Select the Failure/Warning item to be conﬁgured.

3) Click the [Enable] check box to send out the SNMP trap for Failures/Warnings.

Clear the [Enable] check box when SNMP trap transmission is not required.

4) Click the [Apply] button to save the settings.

•

NOTE

• Be sure to execute Network Restart when the settings of [Port Settings] or

[Security Settings] is changed.

Page 92

8. Other Functions

8.3 Event Scheduling

The scheduling function enables to setup scheduled events including power on / power off. It enables to be “self-management” projector.

Note the following before setting the schedule.

NOTE

• Schedule can also be set in SETUP - SCHEDULE menu of the

projector. (Refer to Operating Guide – SETUP).

• A maximum of 16 programs of schedule can be set. A maximum of 20 events

can be registered in 1 program.

• No events are registered in program 1 – 16 with factory default settings. The program is required to be set in advance when using the schedule function for the ﬁrst time.

• The priority for scheduled events is as follows 1) speciﬁc date 2) weekly

• Up to ﬁve speciﬁc dates are available for scheduled events. Priority is given to those with the lower numbers when more than one event has been scheduled for the same date and time (e.g., ‘Speciﬁc date No. 1’ has priority over ‘Speciﬁc

date No. 2’ and so on.

• The power on event has the lowest priority among all the events that are set

at the same time.

• Be sure to set the date and time before enabling scheduled events. (

53)

• After the projector is moved, check the date and time set for the projector before conﬁguring the schedules.

•

The internal clock’s time may not remain accurate. Using SNTP is recommended

to maintain accurate time.

• Certain error state in the projector (such as temperature error, lamp error) will prevent the projector from appropriate execution of scheduled functions/events.

• Events “My Image” and “Messenger” will not be executed appropriately and

result in “schedule execution error” status when the lamp does not light and/or

data to be displayed are not stored in the projector at the time when scheduled

event is executed.

• Events “Input Source” and “My Image” is not executed if security function is

enabled and the projector is locked due to the function.

Page 93

8. Other Functions

The procedure to set the schedule in Projector Web Control is described in the

following.

Setting the program is necessary to use the schedule function. Various events such as power on/off or switching input source, and the time to execute the events are to be registered in the program. No events are registered in program 1 – 16 with factory default settings. Set the program following the steps below.

In the case that the program has already been set, skip to step 6).

1) Select [Schedule Settings] on main menu in Projector Web Control.

2) Select the program number in dropdown list under Program List and click the

[Program Edit] button to display the following program edit display. The display

for editing Program-1 is shown below.

CP-X9110/WX9210/WU9410 CP-X9111/WX9211/WU9411

CP-HD9320/HD9321

3) After setting the time, events and parameters, click the [Register] to add the

new event.

Click the [Delete] button when you want to delete an event. Click the [Delete All] button when you want to delete all the events in the currently

selected program.

Page 94

8. Other Functions

4) When you want to edit the program with other number continuously, select the

program you want to edit in dropdown list and click the [Select] button to display the display for editing the selected program.

5) Click the [Back] button to go back to schedule management screen after

ﬁnishing the program setting.

The procedure to assign the program set in the step 1) ~ 5) to the schedule is

described in the following.

6) Click the checkbox of the schedule to be executed (e.g. Click the checkbox of

“Monday”, when it is to be executed on Mondays) in the schedule management

screen.

7) Select the program to be executed in dropdown list. You can conﬁrm the event

information registered in each program in the program list on the bottom of the screen.

When setting the Speciﬁc date No.1 ~ 5, enter the date (month/day).

8) Click the [Apply] button to save the schedule settings in the projector.

Repeat step 6) ~ 8) similarly to set the schedule you want to execute.

The schedule settings are now complete.

Finally, conﬁrm the time stored in the projector is correctly set.

■How to copy the program

When you copy the currently selected program to other program, click the checkbox under icon. Click the [Copy to] button after selecting the program to which you want to copy in dropdown list.

The same program as the currently selected one cannot be speciﬁed as the

program to which you want to copy.

Page 95

8. Other Functions

8.4 Command Control via the Network

You can conﬁgure and control the projector via the network using RS-232C

commands.

Communication Port

The following two ports are assigned for the command control.

TCP #23 (Network Control Port1 (Port: 23)) TCP #9715 (Network Control Port2 (Port: 9715))

NOTE

Command Control Settings (

• Command control is available only via the speciﬁed port above.

44)

Conﬁgure the following items from a web browser when command control is used.

Example: If the IP address of the projector is set to 192.168.1.10:

1) Enter “http://192.168.1.10/” into the address bar of the web browser, and select

Projector Web Control from the selection window.

2) Enter your user name and password, and then click the [OK].

3) Click the [Port Settings] on the main menu.

4) Click the [Enable] check box to open Network Control Port1 (Port: 23) to use TCP #23. Click the [Enable] check box for the [Authentication] setting when

authentication is required, otherwise clear the check box.

5) Click the [Enable] check box to open Network Control Port2 (Port: 9715) to use TCP #9715. Click the [Enable] check box for the [Authentication] setting

when authentication is required, otherwise clear the check box.

6) Click the [Apply] button to save the settings.

Page 96

8. Other Functions

8.4 Command Control via the Network (continued)

When the authentication setting is enabled, the following settings are required.

55)

(

7) Click the [Security Settings] on the main menu.

8) Click the [Network Control] and enter the desired authentication password.

* See NOTE.

9) Click the [Apply] button to save the settings.

NOTE

• The Authentication Password will be the same for Network Control

Port1 (Port: 23), Network Control Port2 (Port: 9715), PJLink™ Port (Port:

4352), My Image Port (Port: 9716) and Messenger Port (Port: 9719).

• The new conﬁguration settings are activated after restarting the network connection. When the conﬁguration settings are changed, you must restart

the network connection. You can restart the network connection from Network

Restart on the main menu. (

63)

Page 97

8. Other Functions

8.4 Command Control via the Network (continued)

Command Format

Command formats differ among the different communication ports.

● TCP #23

You can use the RS-232C commands without any changes. The reply data format is the same as the RS-232C commands. (

RS-232C Communication



in the Operating Guide - Technical)

However, the following reply will be sent back in the event of authentication

failure when authentication is enabled.

Reply Error code

0x1F 0x04 0x00

● TCP #9715

Send Data format

The following formatting is added to the header (0 x 02), Data length (0 x 0D), Checksum (1 byte) and Connection ID (1 byte) of the RS-232C commands.

Header Data length RS-232Ccommand Check Sum

0x02 0x0D 13 bytes 1 byte 1 byte

Connection

Header → 0x02, Fixed Data length → RS-232C commands byte length (0x0D, Fixed)

RS-232C command → RS-232C commands that start with 0xBE 0xEF

(13 bytes)

Check Sum → This is the value to make zero on the addition of the

lower 8 bits from the header to the checksum.

Connection ID → Random value from 0 to 255 (This value is attached

to the reply data)

Page 98

8. Other Functions

8.4 Command Control via the Network (continued)

Reply Data format

The connection ID (the data is same as the connection ID data on the sending data format) is attached to the RS-232C commands reply data.

0x06 1 byte

0x15 1 byte

Reply Error code

0x1C 2 bytes 1 byte

Reply Data

Connection

0x1D 2 bytes 1 byte

Reply Status code

0x1F 2 bytes 1 byte

0x1F 0x04 0x00 1 byte

Authentication

Error code

Connection

Page 99

8. Other Functions

8.4 Command Control via the Network (continued)

Automatic Connection Break

The TCP connection will be automatically disconnected after there is no

communication for 30 seconds after being established.

Authentication

The projector does not accept commands without authentication success when authentication is enabled. The projector uses a challenge response type

authentication with an MD5 (Message Digest 5) algorithm. When the projector is using a LAN, a random 8 bytes will be returned if authentication is enabled. Bind this received 8 bytes and the Authentication Password and digest this data with the MD5 algorithm and add this in front of the

commands to send.

Following is a sample if the Authentication Password is set to “password” and the random 8 bytes are “a572f60c”.

1) Connect the projector.

2) Receive the random 8 bytes “a572f60c” from the projector.

3) Bind the random 8 bytes “a572f60c” and the Authentication Password “password” and it becomes “a572f60cpassword”.

4) Digest this bind “a572f60cpassword” with MD5 algorithm.

It will be “e3d97429adffa11bce1f7275813d4bde”.

5) Add this “e3d97429adffa11bce1f7275813d4bde” in front of the commands

and send the data.

Send “e3d97429adffa11bce1f7275813d4bde”+command.

6) When the sending data is correct, the command will be performed and the reply data will be returned. Otherwise, an authentication error will be returned.

NOTE

• As for the transmission of the second or subsequent commands, the

authentication data can be omitted when the same connection.

Page 100

8. Other Functions

8.5 Crestron Connected

Crestron ConnectedTM is a multi-user resource management program provided by Crestron Electronics, Inc. It is an application for managing and controlling the projector and other AV devices collectively. For details of Crestron Connected

, refer to the Crestron

URL: http://www.crestron.com

The following communication interfaces can be used to manage the entire facility.

Crestron Fusion RV® / Crestron RoomView® Express / Crestron RoomView® Server Edition

Fusion RV

, RoomView® Express, and RoomView

provided by Crestron Electronics, Inc. They are used for managing all the AV devices, and are also able to communicate with the help desk as well as send

out alert messages. For details of the software, refer to the following website.

URL: http://www.crestron.com/getroomview

2) Crestron e-Control

Crestron e-Control® is a system controller that can be operated via a web

browser. (

65)

website.

Server Edition are software

100