Hitachi CP-AW250 User Manual

Projector

CP-AW250N

User's Manual (detailed) Operating Guide

Thank you for purchasing this projector.

(Type nos. CP-AW250N, CP-AW250NM)

WARNING

►Before using this product, please read all manuals for this product. Be sure to read “Safety Guide” rst. After reading them, store them in a safe place for future reference.

About this manual

Various symbols are used in this manual. The meanings of these symbols are described below.

WARNING

CAUTION

NOTICE This entry notices of fear of causing trouble.

NOTE

• The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this manual.

• The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

Trademark acknowledgment

• Mac® is a registered trademark of Apple Inc.

• Windows in the U.S. and/or other countries.

• VESA and DDC are trademarks of the Video Electronics Standard Association.

•

HDMI, the HDMI logo, and High-Denition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

• Trademark PJLink is a trademark applied for trademark rights in Japan, the United States of America and other countries and areas.

• Blu-ray Disc

All other trademarks are the properties of their respective owners.

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

Please refer to the pages written following this symbol.



, DirectDraw® and Direct3D® are registered trademarks of Microsoft Corporation

and Blu-rayTM are trademarks of Blu-ray Disc Association.

Contents



Introduction . . . . . . . . . . . . . . . 3

Features . . . . . . . . . . . . . . . . . . . . . . 3

Checking the contents of package

Part names . . . . . . . . . . . . . . . . . . . . 4

Setting up . . . . . . . . . . . . . . . . . 7

Arrangement ...................7

Connecting with your devices Connecting to a power supply

......9

.....14

Using the security bar and slot . . . . 14

Using the cable cover ...........15

Remote control ............16

Installing the batteries ...........16

About the remote control signal . . . 16 Changing the frequency of remote control signal Using as a simple PC mouse & keyboard

. . 17

Power on/off . . . . . . . . . . . . . . 18

Turning on the power . . . . . . . . . . . 18

Turning off the power . . . . . . . . . . . 19

Operating . . . . . . . . . . . . . . . . 20

Adjusting the volume ............20

Temporarily muting the sound .....20

Selecting an input signal .........20

Searching an input signal . . . . . . . . 22

Selecting an aspect ratio .........22

Adjusting the projector's elevator . . 23

Adjusting the zoom and focus .....23

Using the automatic adjustment feature

...24

Adjusting the position . . . . . . . . . . . 25

Correcting the keystone distortions

Using the magnify feature ........26

Temporarily freezing the screen . . . 27 Temporarily blanking the screen . . 27

Using the menu function . . . . . . . . 28

EASY MENU. . . . . . . . . . . . . . . 30

As p e c t ,

pe r f e c t f i t

m A

D-z o o m ,

Ke y s t o n e , Ke y s t o n e ,

, pi c t u r e m o D e ,

i r r o r , re s e t , fi l t e r t i m e , lA n g u A g e ,

D v A n c e D m e n u , ex i t

ec o m o D e ,

PICTURE menu . . . . . . . . . . . . 32

Br i g h t n e s s , co n t r A s t , gA m m A , co l o r t e m p , co l o r , ti n t , sh A r p n e s s , Ac t i v e i r is , my m e m o r y

IMAGE menu . . . . . . . . . . . . . . 35

As p e c t , ov e r s c A n , v p o s i t i o n , h p o s i t i o n , h

p h A s e , h s i z e , Au t o A D j u s t e x e c u t e

INPUT menu . . . . . . . . . . . . . . 38

pr o g r e s s i v e , vi D e o n r , co l o r s p A c e , v

i D e o f o r m A t , hD m i f o r m A t , hD m i r A n g e ,

o m p u t e r in , fr A m e l o c K , re s o l u t i o n

SETUP menu ..............42

...3

AUDIO menu . . . . . . . . . . . . . . 45

SCREEN menu .............47

OPTION menu . . . . . . . . . . . . . 53

. . 17

NETWORK menu ...........64

SECURITY menu ...........71

Presentation tools . . . . . . . . . 77

. . 25

Maintenance ..............89

Troubleshooting . . . . . . . . . . . 96

Specications ............104



D-z o o m , D-s h i f t , pi c t .p o s i t .h,

Ke y s t o n e , Ke y s t o n e , pe r f e c t f i t

u t o e c o m o D e , ec o m o D e ,

A s

t A n D B y m o D e , mo n i t o r o u t

mi r r o r ,

vo l u m e , sp e A K e r , Au D i o s o u r c e , h

D m i A u D i o , mi c l e v e l , mi c v o l u m e

lA n g u A g e , me n u p o s i t i o n , Bl A n K , s

t A r t u p ,

e s s A g e , so u r c e n A m e , te m p l A t e , c.c.

yScreen

, M

yScreen Lock

Au t o s e A r c h , Di r e c t p o w e r o n , A

u t o p o w e r o f f , us B t y p e B, lA m p t i m e ,

i l t e r t i m e , my B u t t o n , my s o u r c e ,

e r v i c e

se t u p , pr o j e c t o r n A m e , my i m A g e , A

m x D.D., pr e s e n t A t i o n , in f o r m A t i o n ,

e r v i c e

se c u r i t y p A s s w o r D c h A n g e ,

t m

PC-LESS Presentation

p A s s w o r D , pi n l o c K ,

yScreen

r A n s i t i o n D e t e c t o r , my t e x t p A s s w o r D ,

y t e x t D i s p l A y , my t e x t w r i t i n g

. . . . . . . 77

Thumbnail Mode, Full Screen Mode, Slideshow mode, Playlist

USB Display

..............

Right-Click menu, Floating menu, Options window

Replacing the lamp .............89

Cleaning and replacing the air lter . . 91

Replacing the internal clock battery Caring for the mirror and lens

. . 93

.......94

Other care ....................95

Related messages . . . . . . . . . . . . . 96

Regarding the indicator lamps . . . . 98

Resetting all settings ...........100

Phenomena that may be easy

to be mistaken for machine defects

. 100

Introduction

Features

The projector provides you with the broad use by the following features.

ü The unique lens and mirror system realizes ultra short distance

projection,which gives you more various way of use.

ü The motorized lens door offers you very simple use of the projector.

The double layer lter system is expected to function longer and offers you

less maintenance frequency.

ü The HDMI port can support various image equipment which have digital

interface to get clearer pictures on a screen.

ü This projector can be controlled and monitored via LAN connection. ü This projector's network supports the PJLink

ü PJLink

PJLinkTM enables central control of projectors manufactured by different vendors

is a unied standard for operating and controlling data projectors.

and projectors can be operated by a controller. PJLink can be managed and controlled at any time and in any place, regardless of manufacturer. For the command of PJLink For specications of PJLink and Information System Industries Association.

URL: http://pjlink.jbmia.or.jp (as of Dec. 2009)

, see “Technical”.

, see the web site of the Japan Business Machine

standard.

compliant equipment

Checking the contents of package

Please see the Contents of package section in the User’s Manual (concise) which is a book. Your projector should come with the items shown there. Require of your dealer immediately if any items are missing.

NOTE

to use the original packing materials when moving the projector. Use special caution for the lens.

• Keep the original packing materials, for future reshipment. Be sure

Introduction

Part names

Projector

(1) Lamp cover (89)

The lamp unit is inside. (2) Control panel (5) (3) Elevator feet (x 2) (23) (4) Remote sensor (16) (5) Lens (94) (6) Intake vents (7) Filter cover (91)

The air lter and intake vent

are inside. (8) Battery cover

The internal clock battery is

inside.

(9) Speaker (12, 20, 45) (10) Exhaust vent (11) AC IN (AC inlet) (14) (12) Ports (5) (13) Security bar (14) (14) Security slot (14)

(15) Lens door (94) (16) Mirror (94) (17) Spacer (Small) (23) (18) Spacer (Large) (23)

(17)

Small

(5)

(4)

(3)

(7)

(1)

(6)

(8)

(15)

HOT!

(2)

(16)

(13)

(18)

Large

(12)

(14)

(11)

(10)

HOT!

(9)

(15)

WARNING

►HOT! : Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot. ►Be careful not to pinch your nger with the lens door, to prevent an injury. ►Never look into the projection lens or mirror while the projection lamp lights, since the projection lamp ray may cause a trouble on your eyes. ►Do not use the security bar and slot to prevent the projector from falling down, since it is not designed for it.

CAUTION

►Maintain normal ventilation to prevent the projector from heating up. Do not cover, block or plug up the vents. Do not place anything that can stick or be sucked to the vents, around the intake vents. Clean the air lter periodically.

Control panel

COMPUTER IN1COMPUTER IN2

HDMI

USB TYPE B

S-VIDEO

VIDEO

AUDIO OUT

AUDIO IN3AUDIO IN1

AUDIO IN2

MIC

MONITOR OUT

CONTROL

USB TYPE A DC5V

0.5A

Introduction

(1) STANDBY/ON button ( (2) INPUT button (

20)

18)

(3)

(4)

(6)

(3) POWER indicator (18, 98, 99) (4) TEMP indicator (98, 99) (5) LAMP indicator (98, 99) Buttons ◄/►/▲/▼ (6) FOCUS +/- buttons

when no menu is displayed (24),

(5)

(7)

(2)

(1)

or Cursor ◄/► buttons when a menu is displayed (28). FOCUS +/- function is invalid when the USB TYPE A port is selected as the input source.

(7) MENU buttons

when no menu is displayed (28), or Cursor ▲/▼ buttons when a menu is

displayed (28). The ◄/►/▲/▼ buttons on the projector work only as the cursor buttons while the template is displayed (51).

Ports

(1) USB TYPE A port (2) LAN port (3) HDMI port (4) USB TYPE B port (5) MIC port (6) AUDIO IN1 port (7) AUDIO IN2 port

9 ~ 13)

(

(9) AUDIO OUT (L,R) ports (10) COMPUTER IN1 port (11) COMPUTER IN2 port (12) MONITOR OUT port (13) CONTROL port (14) VIDEO port (15) S-VIDEO port

(8) AUDIO IN3(L,R) ports

(2)

(1)

(13)

(4)

(3) (11)

(5)

(7)

(6)(12)

(8)

(9)

(10)

(14)

(15)

Introduction

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

FOCUS D-ZOOM

- + - +

PAGE UP

DOWN

Remote control

(1) VIDEO button ( (2) COMPUTER button (

21)

(3) SEARCH button (22) (4) STANDBY/ON button (18) (5) ASPECT button (22) (6) AUTO button (24) (7) BLANK button (27) (8) MAGNIFY - ON button (26) (9) MAGNIFY - OFF button (26) (10) MY SOURCE/DOC.CAMERA button (21, 57) (11) VOLUME - button (20) (12) PAGE UP button (17) (13) PAGE DOWN button (17) (14) VOLUME + button (20) (15) MUTE button (20) (16) FREEZE button (27) (17) MY BUTTON - 1 button (56) (18) MY BUTTON - 2 button (56) (19) KEYSTONE button (25) (20) FOCUS - button (24) (21) FOCUS + button (24) (22) D-ZOOM - button (23) (23) D-ZOOM + button (23) (24) POSITION button (25, 29) (25) MENU button (28, 29) (26) ▲/▼/◄/► cursor buttons (28) (27) ENTER button (28, 29) (28) ESC button (28) (29) RESET button (28) (30) Battery cover (16)

(2) (1) (6) (5) (16) (8) (9) (19) (17) (20) (21) (24) (26) (28)

the remote control

(10) (4) (3) (7) (12) (14) (11) (13) (15) (18) (23) (22) (25) (27) (29)

(30)

Back of

Setting up

Install the projector according to the environment and manner the projector will be used in.

Arrangement

Refer to the illustrations and tables below to determine screen size and projection distance. The values shown in the table are calculated for a full size screen: 1280 x 800

Screen size (diagonal) b Projection distance (±8%)

c1 , c2 Screen height (±8%)

• On a horizontal surface

•

Mounted on the wall or ceiling

Screen size

(diagonal)

type(inch)

60 1.5 0.120 4.7 0.295 11.6 1.102 43.4 70 1.8 0.188 7.4 0.332 13.1 1.274 50.2 80 2.0 0.256 10.1 0.369 14.5 1.446 56.9 90 2.3 0.324 12.8 0.407 16.0 1.618 63.7

100 2.5 0.392 15.4 0.444 17.5 1.791 70.5

m m inch m inch m inch

Projection distance c1Screen heightc2Screen height

• If the projector is used at an altitude of about 1600m or higher, set FAN SPEED of the SERVICE item in the OPTION menu to HIGH. Otherwise, set it to NORMAL. If the projector is used with a wrong setting, it may cause damage to the projector itself or the parts inside.

• For the case of installation in special conditions such as on the wall or ceiling, the specied mounting accessories and service may be required. Before installing the projector, consult your dealer about your installation.

•

The screen position may shift after installation if the projector is mounted on locations such as the wall or ceiling, due to the exibility of the plastic projector body. If readjustment is necessary, consult with your dealer or service personnel.

• The projected image position and/or focus may change during warm-up (approx. 30 minutes after the lamp is turned on) or when the ambient conditions change. Readjust the image position and/or focus as necessary.

• Since the projector features an ultra short throw, be aware that it is required to select a screen carefully to have better performance.

- A soft screen such as a pull-down screen may cause serious distortion of a projected

image. A hard screen such as a board screen is recommended for use with this projector.

- A high-gain screen such as a bead screen that has narrow viewing angle is not suitable

for this projector. A low-gain screen (around 1.0) such as a matte screen that has wide viewing angle is recommended for use with this projector.

- A screen with a weave pattern may cause moiré on the projected image, which is not a

failure of the projector. A screen that has less moiré effects is recommended for use with this projector.

(continued on next page)

Setting up

Arrangement (continued)

►

WARNING

Place the projector in a stable horizontal position. If the projector falls or is knocked over, it could cause injury and/or damage to the projector. Using a damaged projector could then result in re and/or electric shock.

• Do not place the projector on an unstable, slanted or vibrational surface such

as a wobbly or inclined stand.

• Do not place the projector on its side, front or rear position.

• Consult with your dealer before a special installation such as on the wall or

ceiling. ►Place the projector in a cool place, and ensure that there is sufcient ventilation. The high temperature of the projector could cause re, burns and/or malfunction of the projector.

• Do not stop-up, block or otherwise cover the projector's vents.

• Keep a space of 30 cm or more between the sides of the projector and other

objects such as walls.

Do not place or attach anything that would block the lens or vent holes.

•

• Do not place the projector on metallic thing or anything weak in heat.

• Do not place the projector on carpet, cushions or bedding.

• Do not place the projector in direct sunlight or near hot objects such as heaters.

Do not place the projector where the air from an air conditioner or similar unit

will blow on it directly.

•

Do not place anything near the projector lens or vents, or on top of the projector.

•

Do not place anything that may be sucked into or stick to the vents on the

bottom of the projector. This projector has some intake vents also on the bottom. ►Do not place the projector anyplace where it may get wet. Getting the projector wet or inserting liquid into the projector could cause re, electric shock and/or malfunction of the projector.

• Do not place the projector in a bathroom or the outdoors.

• Do not place anything containing liquid near the projector.

•

Do not place the projector where any oils, such as cooking or machine oil, are used. ►

Use only the mounting accessories the manufacturer specied, and leave installing

and removing the projector with the mounting accessories to the service personnel.

• Read and keep the user’s manual of the mounting accessories used.

CAUTION

►Avoid placing the projector in smoky, humid or dusty place. Placing the projector in such places could cause re, electric shock and/or malfunction of the projector.

• Do not place the projector near humidiers, smoking spaces or a kitchen. Also do not use an ultrasonic humidier near the projector. Otherwise chlorine and minerals contained in tap water are atomized and could be deposited in the projector causing image degradation or other problems. ►

Position the projector to prevent light from directly hitting the projector's remote sensor. ►Do not place the product in a place where radio interference may be caused. ►Do not place this product in a magnetic eld.

Arrangement (continued)

Setting up

NOTE

• The projector may make a rattling sound when tilted, moved or shaken, since a ap to control the air ow inside of the projector has moved. Be aware that this is not a failure or malfunction.

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to conrm that the device is suitable for connecting with this projector and prepare the required accessories, such as a cable in accord with the signal of the device. Consult your dealer when the required accessory did not come with the product or the accessory is damaged. After making sure that the device and projector are turned off, connect them following the instructions below.

►

WARNING

a re or damage to the device and the projector.

- Use only the accessories specified or recommended by the projector’s manufacturer. Consult your dealer when the required accessory did not come with the product or the accessory is damaged. It may be regulated under some standard.

- For a cable with a core at only one end, connect the end with the core to the projector. That may be required by EMI regulations.

- Neither disassemble nor modify the projector and the accessories.

- Do not use the damaged accessory. Be careful not to damage the accessories.

Route a cable so that it is neither stepped on nor pinched out.

CAUTION

in operation, unless that is directed in the manual of the device. Otherwise it may cause malfunction in the device or projector. ►Be careful not to mistakenly connect a connector to a wrong port. Otherwise it may cause malfunction in the device or projector.

- When connecting a connector to a port, make sure that the shape of the

connector ts the port.

- Tighten the screws to connect a connector equipped with screws to a port.

- Use the cables with straight plugs, not L-shaped ones, as the input ports of the

projector are recessed.

Use only the appropriate accessories. Otherwise it could cause

►Do not turn on or off the projector while connected to a device

(continued on next page)

Connecting with your devices (continued)

• When AUTO is selected for the COMPUTER IN1 or COMPUTER IN2 port in COMPUTER IN of the INPUT menu, that port will accept component video signals (

40).

•

When the USB TYPE B port and the computer's type A USB port are connected, you can use the USB TYPE B port as a picture input port from the computer, or use the remote control as a simple mouse and keyboard of the computer. (

17, 54).

Setting up

(continued on next page)

• Plug-and-Play is a system composed of a computer, its operating system and peripheral equipment (i.e. display devices). This projector is VESA DDC 2B compatible. Plug-and-Play can be used by connecting this projector to a computer that is VESA DDC (display data channel) compatible.

- Take advantage of this feature by connecting a computer cable to the

COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work properly if any other type of connection is attempted.

Please use the standard drivers in your computer as this projector is a Plug-andPlay monitor.

About Plug-and-Play capability

COMPUTER IN1COMPUTER IN2

HDMI

USB TYPE B

S-VIDEO

VIDEO

AUDIO OUT

AUDIO IN3AUDIO IN1

AUDIO IN2

MIC

MONITOR OUT

CONTROL

USB TYPE A DC5V

0.5A

COMPONENT

Cb/Pb

Cr/Pr

AUDIO

OUT

HDMI

VIDEO

S-VIDEO

AUDIO

OUT

AUDIO

OUT

AUDIO

OUT

USB

(A)

DISPLAY

RS-232C

LAN

VCR/DVD/Blu-ray Disc

player

Computer

Connecting with your devices (continued)

Setting up

NOTE

• Before connecting the projector to a computer, consult the computer’s manual and check the compatibility of the signal level, the synchronization methods and the display resolution output to the projector.

- Some signal may need an adapter to input this projector.

- Some computers have multiple screen display modes that may include some

signals which are not supported by this projector.

- Although the projector can display signals with resolution up to UXGA

(1600X1200), the signal will be converted to the projector’s panel resolution before being displayed. The best display performance will be achieved if the resolutions of the input signal and the projector panel are identical.

• If you connect this projector and a notebook computer, you need output the

display to an external monitor, or output simultaneously to the internal display and an external monitor. Consult the computer's manual for the setting.

• Depending on the input signal, the automatic adjustment function of this

projector may take some time and not function correctly.

- Note that a composite sync signal or sync-on-green signal may confuse the

automatic adjustment function of this projector (

40).

- If the automatic adjustment function does not work correctly, you may not see

the dialog to set the display resolution. In such a case, use an external display device. You may be able to see the dialog and set an appropriate display resolution.

(continued on next page)

Setting up

COMPUTER IN1COMPUTER IN2

HDMI

USB TYPE B

S-VIDEO

VIDEO

AUDIO OUT

AUDIO IN3AUDIO IN1

AUDIO IN2

MIC

MONITOR OUT

CONTROL

USB TYPE A DC5V

0.5A

RGB IN

Connecting with your devices (continued)

• If you insert a USB storage device, such as a USB memory, into the USB TYPE A port and select the port as the input source, you can view images stored in the

device (

77).

• You can connect a dynamic microphone to the MIC port with a 3.5 mm mini-plug. In that case, the built-in speaker outputs the sound from the microphone, even while the sound from the projector is output. You can input line level signal to the MIC port from equipment such as wireless microphone. Select HIGH in the MIC LEVEL item of the AUDIO menu when you input line level audio signal to the MIC port. In the normal mode, the volume of the microphone can be adjusted separately from the volume of the projector using the menu. (46)

In the standby mode, the volume of the microphone is adjustable with the

VOLUME +/- buttons on the remote control, in synchronization with the volume of the projector. (20)

Even when the sound of projector is set to mute mode by the AUDIO SOURCE

function (45), the volume of the microphone is adjustable.

In both modes (standby or normal), the MUTE button on the remote control

works on the sounds of the microphone and the projector. (20)

Speakers

Monitor

Microphone system

(with an amplier)

USB storage

device

CAUTION

►Before removing the USB storage device from the port of the projector, be sure to use the REMOVE USB function on the thumbnail screen to secure your data (

NOTE

microphone away from the speaker.

• This projector doesn't support plug-in power for the microphone.

• If a loud feedback noise is produced from the speaker, move the

80).

(continued on next page)

Connecting with your devices (continued)

To use network functions of the projector, connect the LAN port with the computer's LAN port, or with an access point that is connected to the computer with wireless LAN, using a LAN cable. To use NETWORK BRIDGE function, also connect the CONTROL port and an RS-232C port of the external device to communicate as a network terminal. See the User's Manual - Network Guide for details of the network functions.

Setting up

►Before connecting the projector to a network system be sure to obtain the consent of the administrator of the network (

64).

►

Do not connect the LAN port to any network that might have the excessive voltage.

CAUTION

• If an oversized USB storage device blocks the LAN port, use a USB

extension cable to connect the USB storage device.

NOTE

COMPUTER IN1COMPUTER IN2

HDMI

USB TYPE B

S-VIDEO

VIDEO

AUDIO OUT

AUDIO IN3AUDIO IN1

AUDIO IN2

MIC

MONITOR OUT

CONTROL

USB TYPE A DC5V

0.5A

RS-232C

LAN

Access point

Computer

Setting up

Connecting to a power supply

Put the connector of the power cord into the

AC IN (AC inlet) of the projector. Firmly plug the power cord’s plug into the

outlet. In a couple of seconds after the power supply connection, the POWER indicator will light up in steady orange.

Please remember that when the DIRECT POWER ON function activated ( power supply make the projector turn on.

53), the connection of the

AC IN

Power cord

WARNING

incorrect or faulty connections may result in re and/or electrical shock.

• Only use the power cord that came with the projector. If it is damaged, consult your dealer to get a new one.

• Only plug the power cord into an outlet whose voltage is matched to the power cord. The power outlet should be close to the projector and easily accessible. Remove the power cord for complete separation.

• Never modify the power cord.

►Please use extra caution when connecting the power cord, as

Using the security bar and slot

A commercial anti-theft chain or wire up to 10 mm in diameter can be attached to the security bar on the projector. Also this product has the security slot for the Kensington lock. For details, see the manual of the security tool.

Anti-theft chain or wire

WARNING

from falling down, since it is not designed for it.

CAUTION

It may become too hot.

►Do not use the security bar and slot to prevent the projector

►Do not place anti-theft chain or wire near the exhaust vents.

Security slot

Security bar

NOTE

measures. It is intended to be used as supplemental theft prevention measure.

• The security bar and slot is not comprehensive theft prevention

Setting up

Using the cable cover

Utilize the cable cover as the guard and blind for the connecting parts.

Connect the signal cables and the power cord to the projector rst.

Combine parts as shown in gure,

and assemble the cable cover.

Insert the three knobs on the cable cover into the three holes on the projector

as shown in the gure. Pass the cables through the holes on the bottom of

the cable cover.

knobs

CAUTION

prevent damage to the cables.

► Be careful not to pinch the cables in the cable cover, to

► Use the cable cover that is supplied with the projector. Do not attempt any modications to the cable cover.

Remote control

Installing the batteries

Please insert the batteries into the remote control before using it. If the remote control starts to malfunction, try to replace the batteries. If you will not use the remote control for long period, remove the batteries from the remote control and store them in a safe place.

Holding the hook part of the battery

cover, remove it. Align and insert the two AA batteries

(HITACHI MAXELL, Part No.LR6 or R6P) according to their plus and minus terminals as indicated in the remote control. Replace the battery cover in the direction of the arrow and snap it back into place.

21 3

WARNING

directed. Improper use may result in battery explosion, cracking or leakage, which could result in re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specied. Do not use batteries of different types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not place a battery in a re or water. Keep batteries in a dark, cool and dry place.

• If you observe battery leakage, wipe out the leakage and then replace a battery. If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

►Always handle the batteries with care and use them only as

About the remote control signal

The remote control works with the projector’s remote sensor. This projector has a remote sensor on the front. The sensor senses the signal within the following range when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor) within 3 meters about.

•

NOTE

If it is difcult to send the signal to the sensor directly, attempt to make the signal reect.

• The remote control uses infrared light to send signals to the projector (Class 1 LED), so be sure to use the remote control in an area free from obstacles that could block the remote control’s signal to the projector.

•

The remote control may not work correctly if strong light (such as direct sun light) or light from an extremely close range (such as from an inverter uorescent lamp) shines on the remote sensor of the projector. Adjust the position of projector avoiding those lights.

The remote control signal reected in the screen or the like may be available.

30º

Approx.

3 m

Remote control

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

FOCUS D-ZOOM

- + - +

PAGE UP

DOWN

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

FOCUS D-ZOOM

- + - +

PAGE UP

DOWN

USB TYPE B

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control does not function properly, attempt to change the signal frequency. In order to set the Mode, please keep pressing the combination of two buttons listed below simultaneously for about 3 seconds.

(2)

(1) Set to Mode 1:NORMAL... VOLUME - and RESET buttons (2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons

Please remember that the REMOTE FREQ. in the SERVICE item of the OPTION menu

(60)

of the projector to be controlled should be

set to the same mode as the remote control.

Using as a simple PC mouse & keyboard

The accessory remote control works as a simple mouse and keyboard of the computer, when the projector’s USB TYPE B port and the computer’s type A USB port are connected and MOUSE is selected for the USB TYPE B item in the OPTION menu (

(1) PAGE UP key: Press PAGE UP button. (2) PAGE DOWN key: Press PAGE DOWN button. (3) Mouse left button: Press ENTER button. (4)

Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►. (5) ESC key: Press ESC button. (6) Mouse right button: Press RESET button.

54).

USB TYPE B port

(1)

(2)

NOTICE

function could damage your equipment. While using this

►Improper use of the simple mouse & keyboard

(3) function, please connect this product only to a computer. Be sure to check your computer’s manuals before connecting this product to the computer.

NOTE

When the simple mouse & keyboard function of this product does not work

(5)

correctly, please check the following.

• When a USB cable connects this projector with a computer having a built-in pointing device (e.g. track ball) like a laptop PC, open BIOS setup menu, then select the external mouse and disable the built-in pointing device, because the built-in pointing device may have priority to this function.

Windows 95 OSR 2.1 or higher is required for this function. And also this function may not work

• depending on the computer’s congurations and mouse drivers. This function can work with the computer which can operate general USB mouse or keyboard.

• You cannot do things like press two buttons at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

This function is activated only when the projector is working properly. This function is not

• available in any of the following cases:

- While the lamp is warming up. (The POWER indicator blinks in green.)

- When either USB TYPE A or USB TYPE B port is selected.

- While displaying BLANK

- When any menu is displayed on the screen. While using the cursor buttons to operate the sound or screen functions such as adjusting the

sound volume, correcting the keystone, correcting the picture position and magnifying the screen.

(27)

, TEMPLATE

(51)

or MY IMAGE

(67)

screen.

(4)

(6)

Power on/off

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ーONOFF

＋

FREEZE

FOCUS D-ZOOM

- + - +

PAGE UP

DOWN

Power on/off

Turning on the power

Make sure that the power cord is rmly

and correctly connected to the projector and the outlet. Make sure that the POWER indicator is

steady orange ( Conrm that there is nothing that the lens

door hits while opening. Press STANDBY/

98).

ON button on the projector or the remote control. The lens door opens, the projection lamp lights up, and the POWER indicator begins to blink green. When the power is completely on, the indicator will stop blinking and light in steady green

(

98).

WARNING ►Never look into the projection lens or mirror while

the projection lamp lights, since the projection lamp ray may cause a trouble on your eyes. ►

Be careful not to pinch your nger with the lens door, to prevent an injury. ►Do not place the projector vertically with the lens door open as shown in the gure on the right. It could cause malfunction or injury.

►Do not stand under the projector mounted on the wall or ceiling, when its lens door is opening or closing. Moreover, do not look at the

mirror when the lens door is opening or closing. ►Never touch a lens door or mirror. If the mirror is broken, the

projected image will be distorted. Close the lens door, and contact your dealer.

STANDBY/ON button POWER indicator

Power on/off

Turning off the power

Press the STANDBY/ON button on the projector or the remote control.

The message “Power off?” will appear on the screen for about 5 seconds. Conrm that there is nothing that the lens door hits while closing.

Press the STANDBY/ON button again while the message appears. The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete (

Do not turn the projector on for about 10 minutes or more after turning it off. Also, do not turn the projector off shortly after turning it on. Such operations might cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.

98).

WARNING

prevent an injury.

►Do not touch around the lamp cover and the exhaust vents during use or just after use, since it is too hot. ►Remove the power cord for complete separation. The power outlet should be close to the projector and easily accessible.

NOTE

prior to the connected devices.

•

This projector has the function that can make the projector automatically turn on/ off. Please refer to the DIRECT POWER ON items of the OPTION menu.

• Turn the power on/off in right order. Please power on the projector

►Be careful not to pinch your nger with the lens door, to

(53)

and AUTO POWER OFF

(54)

Operating

VIDEO

DOC.CAMERA

ASPECT SEARCH

BLANK

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

PAGE UP

DOWN

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

PAGE UP

DOWN

Operating

VOLUME +/- button

Adjusting the volume

Use the VOLUME +/VOLUME - buttons to adjust the volume.

A dialog will appear on the screen to aid you in adjusting the volume. If you do not do anything, the dialog will automatically disappear after a few seconds.

● When disabled. Please see AUDIO SOURCE item of AUDIO menu (

● Even if the projector is in the standby mode, the volume is adjustable when both of the following conditions are true:

- An option other than

● In the standby mode, the volume of the microphone is adjustable with the VOLUME +/- buttons on the remote control, in synchronization with the volume of the projector

Temporarily muting the sound

Press MUTE button on the remote control.

A dialog will appear on the screen indicating that you have muted the sound. To restore the sound, press the MUTE, VOLUME + or VOLUME - button. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

● When is selected for current picture input port, the sound is always muted. Please see AUDIO SOURCE item of AUDIO menu (

● C.C. (Closed Caption) is automatically activated when sound is muted and an input signal containing C.C. is received. This function is available only when the signal is NTSC for VIDEO or S-VIDEO, or 480i@60 for COMPUTER IN1 or COMPUTER IN2, and when AUTO is selected for DISPLAY in the C.C. menu under the SCREEN menu (52).

Selecting an input signal

Press INPUT button on the projector.

Each time you press the button, the projector switches its input port from the current port as below.

VIDEO LAN

is selected for current picture input port, the volume adjustment is

45).

is selected for STANDBY in the AUDIO SOURCE

item of the AUDIO menu

(

45).

NORMAL is selected in the STANDBY MODE item of the SETUP menu

(12)

MUTE button

45).

INPUT button

COMPUTER IN1  COMPUTER IN2

(44).

S-VIDEO USB TYPE A

●

While ON is selected for AUTO SEARCH item in OPTION menu (53), the projector will keep checking the ports in above order repeatedly till an input signal is detected.

●

It may take several seconds to project the images from the USB TYPE B port.

(continued on next page)

HDMI  USB TYPE B

Selecting an input signal (continued)

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

PAGE UP

DOWN

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

PAGE UP

DOWN

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

PAGE UP

DOWN

Operating

Press COMPUTER button on the remote control.

Each time you press the button, the projector switches its input port from the current port as below.

COMPUTER IN1  COMPUTER IN2  LAN USB TYPE B  USB TYPE A

● While ON is selected for AUTO SEARCH item in OPTION menu, the projector will keep checking every port sequentially till an input signal is detected (

53). If COMPUTER button is pressed when VIDEO, S-VIDEO or HDMI port is selected, the projector will check COMPUTER IN1 port rst.

● It may take several seconds to project the images from the USB TYPE B port.

Press VIDEO button on the remote control.

Each time you press the button, the projector switches its input port from the current port as below.

HDMI  S-VIDEO

VIDEO

●

While ON is selected for AUTO SEARCH item in OPTION menu, the projector will keep checking every port sequentially till an input signal is detected (

53). If VIDEO button is pressed when COMPUTER IN1, COMPUTER IN2, LAN, USB TYPE A or USB TYPE B port is selected, the projector will check HDMI port rst.

COMPUTER button

VIDEO button

Press the MY SOURCE / DOC. CAMERA button on

the remote control. The input signal will be changed into the signal you set as MY SOURCE (

57).

● This function also can use for document camera. Select the input port that connected the document camera.

MY SOURCE / DOC. CAMERA button

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

PAGE UP

DOWN

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

PAGE UP

DOWN

Searching an input signal

Press SEARCH button on the remote control.

The projector will start to check its input ports as below in

SEARCH button

order to nd any input signals. When an input is found, the projector will stop searching and display the image. If no signal is found, the projector will return to the state selected before the operation.

COMPUTER IN1  COMPUTER IN2

VIDEO LAN

S-VIDEO USB TYPE A

HDMI  USB TYPE B

● While ON is selected for AUTO SEARCH item in OPTION menu (53), the projector will keep checking the ports in above order repeatedly till an input signal is detected. It may take several seconds to project the images from the USB TYPE B port.

●

Selecting an aspect ratio

Press ASPECT button on the remote control.

Each time you press the button, the projector switches the mode for aspect ratio in turn.

 For a computer signal

NORMAL  4:3  16:9  16:10  NATIVE

ASPECT button

 For an HDMI signal

NORMAL  4:3  16:9  16:10  14:9  NATIVE

 For a video signal, s-video signal or component video signal

4:3  16:9  16:10  14:9  NATIVE

 For an input signal from the LAN, USB TYPE A or USB TYPE B port, or

if there is no signal

16:10 (xed)

● ASPECT button does not work when no proper signal is inputted.

● NORMAL mode keeps the original aspect ratio setting.

● The on-screen menu might be displayed outside of the image display area

depending on the adjustment value of the ASPECT, D-ZOOM, KEYSTONE and KEYSTONE. Changing the values of ASPECT, D-ZOOM,

KEYSTONE and KEYSTONE may x the symptom.

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

FOCUS D-ZOOM

- + - +

PAGE UP

DOWN

Adjusting the projector's elevator

The projector has Front foot for inclinations and Rear foot for horizontals. Spacers on the each elevator foot are installed at the time of shipment, and projector is in a condition to be able to just project. If necessary, detach the spacer, and the elevator feet can be manually twisted to make more precise adjustments.

2.3~4.3°

Front foot Rear foot

Spacer

Front foot

Spacer (Large)

Rear foot

-1~1°

Spacer (Small)

WARNING

►Keep the spacers away from children and pets. Be careful not to let them swallow the spacers. If swallowed consult a physician immediately for emergency treatment.

NOTE

• The adjustment angle can be adjusted up to plus or minus 1° each of

FRONT and REAR foot.

•

After the foot is adjusted, it is possible to return it to the state of the shipment with a spacer. Install Large on the Front foot and Small on the Rear foot of the spacer. If change the setting place of the projector, it will recommend keep and reuse the spacers.

Adjusting the zoom and focus

Press the D-ZOOM + or D-ZOOM – button on the remote control to display D-ZOOM dialog on screen. Use the D-ZOOM + and D-ZOOM – buttons to adjust the picture size. To nish the operation, do not touch these buttons for a few seconds until the dialog is disappeared.

● If you want to expand a part of the image, use the magnify function (

26).

D-ZOOM - button

D-ZOOM + button

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

PAGE UP

DOWN

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

FOCUS D-ZOOM

- + - +

PAGE UP

DOWN

Press the FOCUS + or FOCUS – button on the remote control, or FOCUS + or FOCUS – button on the projector

(5)

FOCUS - button

while no menu is on screen, to display the FOCUS box on screen. Use the FOCUS + and FOCUS – buttons to adjust the screen focus. After the focus adjustment, wait for a while until the FOCUS box is disappeared, if you want to display any other menu on screen by pushing the MENU button on the projector.

● The ◄/►/▲/▼ buttons on the projector work only as the cursor buttons while the template is displayed (51).

● FOCUS +/- button on the projector is invalid when the USB

FOCUS + button

TYPE A port is selected as the input source.

Using the automatic adjustment feature

Press AUTO button on the remote control.

Pressing this button performs the following.

 For a computer signal

The vertical position, the horizontal position and the horizontal phase will be automatically adjusted. Make sure that the application window is set to its maximum size prior to attempting to use this feature. A dark picture may still be incorrectly adjusted. Use a bright picture when adjusting.

 For a video signal and s-video signal

The video format best suited for the respective input signal will be selected automatically. This function is available only when the AUTO is selected for

39).

the VIDEO FORMAT item in the INPUT menu (

The vertical position and

horizontal position will be automatically set to the default.

 For a component video signal

The vertical position and horizontal position will be automatically set to the default. The horizontal phase will be automatically adjusted.

● The automatic adjustment operation requires approx. 10 seconds. Also please note that it may not function correctly with some input.

● When this function is performed for a video signal, a certain extra such as a line may appear outside a picture.

● When this function is performed for a computer signal, a black frame may be displayed on the edge of the screen, depending on the PC model. The items adjusted by this function may vary when the FINE or DISABLE is selected

● for the AUTO ADJUST item of the SERVICE item in the OPTION menu (

AUTO button

58).

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

FOCUS D-ZOOM

- + - +

PAGE UP

DOWN

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

PAGE UP

DOWN

Adjusting the position

Press the POSITION button on the remote control while no menu

is on screen, to display the D-SHIFT

Use the ▲, ▼, ◄ and ► buttons to adjust the picture position.

Press the POSITION button again to nish this operation.

● This is a function to shift the position of the shrunken picture by the D-ZOOM function.

● When an OSD (On Screen Display) menu is displayed, this operation moves the position of the OSD menu, but the picture position is not

● The D-SHIFT adjustment values are not valid when the D-ZOOM is set to 320 (full screen).

(42)

dialog on screen.

(29)

POSITION button

(42)

Correcting the keystone distortions

Press KEYSTONE button on the remote

control. A dialog will appear on the screen to aid you in correcting the distortion.

Use the ▲/▼ cursor buttons to select MANUAL or PERFECT

FIT operation, and press the ► button to perform the following. (1) MANUAL displays a dialog for keystone correction.

Use the ▲/▼ buttons to select KEYSTONE /

KEYSTONE, then use the ◄/► buttons for

adjustment.

(2) PERFECT FIT displays a dialog for adjusting the shape

of the projected image in each of the corners and sides.

To close the dialog and complete this operation, press KEYSTONE button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.

● The adjustable range of this function will vary among inputs. For some input, this function may not work well.

● This function will be unavailable when Transition Detector is on (

KEYSTONE button

74).

Operating

VIDEO

DOC.CAMERA

ASPECT SEARCH

BLANK

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

PAGE UP

DOWN

Using the magnify feature

Press the MAGNIFY ON button on the remote control.

The picture will be magnied, and the MAGNIFY dialog will

MAGNIFY ON/OFF button

appear on the screen. When the MAGNIFY ON button is pressed for the rst time after the projector is turned on, the picture will be zoomed by 1.5 times. On the dialog, triangle marks to show each direction will be displayed.

The display magnication of the projector switches in order

with every press of the MAGNIFY button.

 For computer signals, HDMI (RGB) signals, input signals from the

LAN or USB TYPE B port

1.5 times  2 times  3 times  4 times  1 time

 For video signals, s-video signals, component video signals or HDMI

(Component) signals

1.5 times  2 times  1 time

While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor

buttons to shift the magnifying area.

Press the MAGNIFY OFF button on the remote control to exit magnication.

● The MAGNIFY dialog will automatically disappear in several seconds with no operation. The dialog will appear again if the MAGNIFY ON button is pressed when the dialog has automatically disappeared.

● The magnication is automatically disabled when the displaying signal or its display condition is changed.

● While the magnication is active, the keystone distortion condition may vary. It will be restored when the magnication is disabled.

● Some horizontal stripes might be visible on the image while magnication is active.

● This function is not available in the following cases:

- The USB TYPE A port is selected as the input source.

- A sync signal in the range not supported is input.

- There is no input signal.

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

PAGE UP

DOWN

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

1 2

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

OFF

＋

FREEZE

PAGE UP

DOWN

Temporarily freezing the screen

Press the FREEZE button on the remote control.

The “FREEZE” indication will appear on the screen (however, the indication will not appear when the OFF is selected for the MESSAGE item in the SCREEN menu (

49)), and the projector will go into the FREEZE mode, which the picture is frozen. To exit the FREEZE mode and restore the screen to normal, press the FREEZE button again.

● The projector automatically exits from the FREEZE mode when some control buttons are pressed.

● If the projector continues projecting a still image for a long time, the LCD panel might possibly be burned in. Do not leave the projector in the FREEZE mode for too long.

● Images might appear degraded when this function is operated, but it is not a malfunction.

FREEZE button

Temporarily blanking the screen

Press BLANK button on the remote control.

The BLANK screen will be displayed instead of the screen of input signal. Please refer to BLANK item in SCREEN menu

(

47). To exit from the BLANK screen and return to the input signal screen, press BLANK button again.

BLANK button

● The projector automatically exits from the

BLANK

mode when

some control buttons are pressed.

CAUTION

►If you wish to have a blank screen while the projector's lamp is on, use the BLANK function above. Taking any other action may cause the damage on the projector.

•

NOTE

The sound is not connected with the BLANK screen function. If necessary, set the volume or mute rst. To display the BLANK screen and mute the sound at one time, use AV MUTE function

(57).

Operating

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ーONOFF

＋

FREEZE

FOCUS D-ZOOM

- + - +

PAGE UP

DOWN

VIDEO

DOC.CAMERA

KEYSTONE

ASPECT SEARCH

BLANK

MUTE

MY BUTTON

POSITION

1 2

ESC

ENTER

RESET

COMPUTER

MY SOURCE/

AUTO

MAGNIFY

VOLUME

ー

＋

FREEZE

FOCUS D-ZOOM

- + - +

PAGE UP

DOWN

Using the menu function

This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, SECURITY and EASY MENU. EASY MENU consists of functions often used, and the other menus are classied into each purpose and brought together as the ADVANCED MENU. Each of these menus is operated using the same methods. While the projector is displaying any menu, the MENU button on the projector works as the cursor buttons. The basic operations of these menus are as follows.

To start the MENU, press the MENU button. The MENU you last used (EASY

or ADVANCED) will appear. EASY MENU has priority to appear just after powered on.

In the EASY MENU

(1) Use the ▲/▼ cursor buttons to select an item to

operate. If you want to change it to the ADVANCED MENU, select the ADVANCED MENU.

(2) Use the ◄/► cursor buttons to operate the item.

In the ADVANCED MENU

(1) Use the ▲/▼ cursor buttons to select a menu.

If you want to change it to the EASY MENU, select the EASY MENU. The items in the menu appear on the right side.

(2) Press the ► cursor button or ENTER button to

move the cursor to the right side. Then use the ▲/▼ cursor buttons to select an item to operate and press the ► cursor

(continued on next page)

button or ENTER button to progress. The operation menu or dialog of the selected item will appear.

(3) Use the buttons as instructed in the OSD to operate the item.

ENTER button MENU button

Cursor buttons

MENU button (Cursor buttons)

ESC button

RESET button

Operating

Using the menu function (continued)

To close the MENU, press the MENU button again or select EXIT and press

the ◄ cursor button or ENTER button. Even if you do not do anything, the dialog will automatically disappear after about 30 seconds.

●

If you want to move the menu position, use the cursor buttons after pressing the POSITION button.

● Some functions cannot be performed when a certain input port is selected, or when a certain input signal is displayed.

● When you want to reset the operation, press RESET button on the remote control during the operation. Note that some items (ex. LANGUAGE, VOLUME) cannot be reset.

● In the ADVANCED MENU, when you want to return to the previous display, press the ◄ cursor button or ESC button on the remote control.

Indication in OSD (On Screen Display)

The meanings of the general words on the OSD are as follows.

Indication Meaning

EXIT

RETURN Selecting this word returns the menu to the previous menu.

CANCEL or NO

OK or YES

Selecting this word nishes the OSD menu. It's the same as pressing the MENU button.

Selecting this word cancels the operation in the present menu and returns to the previous menu.

Selecting this word executes the prepared function or shifts the menu to the next menu.

EASY MENU

From the EASY MENU, items shown in the table below can be performed. Select an item using the ▲/▼ cursor buttons. Then perform it according to the following table.

Item Description

ASPECT

D-ZOOM

KEYSTONE

PERFECT FIT

Using the ◄/► buttons switches the mode for aspect ratio. See the ASPECT item in IMAGE menu (

Using the ◄/► cursor buttons adjusts the magnication ratio.

Small ó Large

See the D-ZOOM item in the SETUP menu (

• The on-screen menu might be displayed outside of the image display area depending on the adjustment value of the ASPECT, D-ZOOM, of ASPECT, D-ZOOM, the symptom.

Using the ◄/► buttons corrects the vertical keystone distortion. See the

Using the ◄/► buttons corrects the horizontal keystone distortion. See the

Pressing the ► button displays the dialog for adjusting the shape of the projected image in each of the corners and sides. See the PERFECT FIT item in SETUP menu (

KEYSTON and KEYSTONE. Changing the values

KEYSTONE and KEYSTONE may x

KEYSTONE item in SETUP menu (

KEYSTONE item in SETUP Menu (



43).

35).



42).



42).

43).

(continued on next page)

+ 74 hidden pages