Hitachi CM721F User Manual
COLOR MONITOR
USER’S MANUAL
CM721F
MANUEL D’UTILISATION
READ THE INSTRUCTIONS INSIDE CAREFULLY.
KEEP THIS USER MANUAL FOR FUTURE REFERENCE.
For future reference, record the serial number of your color monitor.
SERIAL No.
The serial number is located on the rear of the monitor.
This monitor is ENERGY STAR® compliant when used with a computer
equipped with VESA DPMS.
The ENERGY STAR® emblem does not represent EPA endorsement of
any product or service.
As an ENERGY STAR® Partner, Hitachi,Ltd. has determined that this
product meets the ENERGY STAR® guidelines for energy efficiency.
1
Table of Content
s
Introduction..................................................................2
Features
Package Overview
Cautions..................................................................... 3
FCC Statement Warning.............................................. 5
TCO'99 Statement .......................................................7
For the Customers in the UK .........................................10
Limited Warranty for USA Customers Only.....................11
For Canadian Customers only Warranty Policy...............13
Installation...................................................................14
User Controls ............................................................ 15
OSD Function Description............................................ 16
OSD Icon Summary .................................................... 17
Specifications ............................................................. 19
Troubleshooting .......................................................... 20
Moni-
2
INTRODUCTION
Congratulations on your purchase of this high performance
19”moniter.Using state-of-the-art electronics, this monitor can support a
maximum resolution of 1600 x 1200 . The on-screen display(OSD) allows
you to customize the display settings to suit your individual needs.
Features
J 19-inch monitor with a large, 366
x 274 mm viewable screen for
comfortable viewing.
J OSD user controls for easy and
accurate adjustment of the screen
image.
J Energy Star compliant to reduce
power consumption.
Package Overview
Please make sure the following items are in the shipping packing and found
in good condition:
* 19" Monitor * Power cord
* Tilt and swivel stand * This manual
Note:
Please save this packing material in case the monitor needs warranty service
in the future. You must return the monitor in its original packing materials
for warranty service or you will be required to purchase new packing materials that comply with Hitachi’s packaging standards.
3
CAUTIONS
NEVER REMOVE THE REAR COVER !
The rear cover MUST be removed only by authorized service personnel. This color monitor contains
high voltage components.
THE RECEPTACLE SHOULD BE CLOSE TO THE MONITOR AND EASILY ACCESSIBLE !
INSTALL THE UNIT IN A SUITABLE ENVIRONMENT !
DO NOT expose this monitor to rain or moisture to prevent electric shock or fire hazard. This unit is
designed to be used in an office or business environment.
DO NOT subject the unit to vibrations, dust, or corrosive gases.
KEEP IN A WELL VENTILATED PLACE !
DO NOT cover this monitor or place anything against any sides (not only the top, right and left side
but also the rear and bottom side ) of unit. Ventilation holes are provided at all sides of the rear cover
to prevent the temperature from rising.
KEEP AWAY FROM HEAT SOURCES !
AVOID placing the unit in direct sunshine or near a heating appliance.
BE CAREFUL OF MAGNETIC FIELDS !
DO NOT place a magnet, loudspeaker system, floppy disk drive, printer, or anything which will
generate magnetism near the unit. A magnetic field may cause blurred colors or distortion of the
displayed pattern.
BE CAREFUL OF GENERATED MAGNETISM !
After the power has been turned on or “DEGAUSS” button has been pressed, the CRT is demagnetized for approximately 10 seconds. This generates a strong magnetic field around the front cover
which may affect the data stored on magnetic tape or disks near the front cover. Place such
magnetic recording equipment and tapes/disks away from this unit.
AMBIENT ILLUMINATION
Avoid direct rays of the sun or room lighting onto the CRT screen in order to prevent eye fatigue.
THE ENCLOSED POWER CORD MUST BE USED !
In Europe, a proper European standard approved power cord is to be used with this monitor. For a
rated current up to 6 A, a type not lighter than H05VV-F 3G 0.75 mm2 or H05VVH2-F 3G 0.75 mm
2
must be used.
In USA/Canada, use a UL LISTED/CSA LABELLED or CERTIFIED power cord set meeting the
following specifications
Rating: min. 125V, 7A
Length: max. 3.0m
Type: SVT or SJT
Plug type: NEMA 5-15P figure, Parallel blade, Grounding type
Failure to do so may cause fire or electric shock hazard.
USE ONLY THE CORRECT VOLTAGE POWER OUTLET WITH SAFETY GROUND
CONNECTION !
100 - 120 V for USA, Canada, etc.
200 - 240 V for Europe, etc.
(This monitor will automatically adjust to the input voltage 100 - 120 / 200 - 240V.)
4
CAUTION for 200 - 240V operation only
This equipment relies on the protective devices in the building installation for short-circuit and over-
current protection. Refer to the following table for the suitable number and location of the protective
devices which should be provided in the building installation.
Informative examples of
protective devices in single - phase equipment or sub - assemblies
Protection
against
Minimum number of
fuses or circuit -
breaker poles
Location
Case A: Equipment to be
connected to POWER SYSTEMS
with earthed neutral reliably
identified, except for Case C below.
Earth faults
Overcurrent
1
1
Phase conductor
Either of the two
conductors
Case B: Equipment to be
connected to any supply, including
IT POWER SYSTEMS and supplies
with reversible plugs, except for
Case C below.
Earth faults
Overcurrent
2
1
Both conductors
Either of the two
conductors
Case C: Equipment to be
connected to 3-wire power systems
with earthed neutral reliably
identified.
Earth faults
Overcurrent
2
2
Each phase conductor
Each phase conductor
Verify that the protective devices in the building installation meets the conditions in the table prior to
installing the equipment.
BE CAREFUL OF POWER CORD CONNECTION !
Before inserting the plug of the power cord into a receptacle of the correct voltage, check that the
connection portion of the power cord is clean (with no dust). Then, insert the plug of power cord to a
receptacle firmly, otherwise it may cause electrical shock or fire.
REMOVE THE POWER CORD FOR COMPLETE SEPARATION !
For complete separation from the power source, remove the power cord from the monitor or from the
wall outlet.
AVOID FREQUENT POWER ON-OFF SWITCHING !
DO NOT repeat OFF and ON in a short period. It may cause blurred colors or distortion of the
displayed pattern.
BE CAREFUL OF STATIC ELECTRICITY ON CRT SURFACE !
To prevent electrical shock by the static electricity on the CRT surface, disconnect the power cord at
least 30 SECONDS AFTER turning off the power.
ABOUT CLEANING
This monitor has a non-glare and anti-electrostatic treatment on the surface of the screen. Use
water or alcoholic solvent with soft cloth like gauze to clean the surface of the screen.
NEVER use abrasive, glass cleaner containing highly concentrated ammonia and strong base
chemicals since they damage the surface treatment.
Clean the cabinet and controls with a lightly moistened soft cloth.
DO NOT use aerosol sprays, solvents or abrasive cleaners.
5
CAUTIONS (Continued)
FCC Statement Warning
WARNING : This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio / TV technician for help.
INSTRUCTIONS TO USERS : This equipment complies with the requirements of FCC (Federal Communication
Commission) equipments provided that following conditions are met.
(1) Power cord: Unshielded power cord must be used.
(2) ceed the specified level.
CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Declaration of Conformity
According to 47CFR, Part 2 and 15 for
Class B Personal Computers and
Peripherals; and / or
CPU Boards and Power Supplies used
With Class B Personal Computers:
We: HITACHI America, Ltd.
Located at: 2000 Sierra Point Parkway, Brisbane, CA 94005-1835 U.S.A.
Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of
the FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit
tested and found to be compliant with the standards.. Records maintained continue to reflect the
equipment being produced can be expected to be within the variation accepted, due to quantity production
and testing on a statistical basis as required by 47FCR § 2.909. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation. The above named party
is responsible for ensuring that the equipment complies with the standards of 47CFR §§ 15.101 to
15.109.
Trade name: Color Monitor
Model Number: CM721F
Signature of Party Responsible:
Printed name of Party Responsible: Hideaki Kusaba
Executed on (Date), at (Place): May 18, 2001, CA, U.S.A.
6
For the Customers in CANADA
NOTICE : This Class B digital apparatus complies with Canadian ICES-003.
Loading...