Page 1
LIST No.
CM 4ST: E725
Aug. 2010
[SAME FEATURES AS THE CONVENTIONAL MODELS]
Dust-proof Switch
Low vibration and noise
Compact body
Smart gear cover and base
The Model CM 4ST is the 4” cutter version of the low-end ST series model based on the CM 4SB.
Overload strength is increased by adopting a powerful motor with maximum output of 1,950 W, while a rubbe
r
cover over the switch trigger section and lock button prevents the entry of dust, thus improving durability.
We are marketing this new 4” cutter with these features to increase market share and expand sales.
PRODUCT NAME
Hitachi 4” Cutter
Model CM 4ST
• Cutting and scribing of concrete, stone brick, tile, and similar materials
MARKETING OBJECTIVE
APPLICATIONS
SELLING POINTS
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.
[NEW FEATURES]
Powerful Motor
C
International Sales Division
Page 2
REMARK:
• For more information about HANDLING INSTRUCTIONS, visit our website at:
http://www.hitachi-koki.com/manual_view_export/
• Throughout this TECHNICAL DATA AND SERVICE MANUAL, a symbol(s) is(are) used in the place of
company name(s) and model name(s) of our competitor(s). The symbol(s) utilized here is(are) as follows:
Competitors
Symbols Utilized
Company Name Model Name
C MAKITA 4100NHZ
Page 3
CONTENTS
Page
SELLING POINTS -------------------------------------------------------------------------------------------------------------- 1
SPECIFICATIONS --------------------------------------------------------------------------------------------------------------3
1. Specifications
--------------------------------------------------------------------------------------------------------------------------------- 3
COMPARISON WITH SIMILAR PRODUCTS---------------------------------------------------------------------------- 4
1. Comparison of Specifications --------------------------------------------------------------------------------- 4
PRECAUTIONS ON SALES PROMOTION ------------------------------------------------------------------------------ 5
1. Safety Instructions -----------------------------------------------------------------------------------------------5
REPAIR GUIDE------------------------------------------------------------------------------------------------------------------ 7
1. Precautions on Disassembly and Reassembly ----------------------------------------------------------- 7
STANDARD REPAIR TIME (UNIT) SCHEDULES-------------------------------------------------------------------- 11
Assembly Diagram for CM 4ST
Page 4
-1-
<Comparison of motor performance>
Maker
Model
Item
HITACHI
CM 4ST
C
Maximum output W 1,950 1,640
Overload strength % 121 100
0
50
100
150
200
250
300
350
100%
121%
HITACHI CM 4ST
1.15 1.40
Torque (N•m)
Stator coil temperature rise (°C)
C
Excellent overload durability
The powerful motor with maximum output of 1,950 W achieves overload durability 1.2 times greater than
that of the conventional model.
Dust-proof switch
Because the switch trigger section and lock button are both covered with rubber, this model is structured to
prevent the entry of dust into the handle that contains the switch and wiring.
SELLING POINT DESCRIPTIONS
SELLING POINTS
<Provision of rubber cover>
Maker
Model
Item
HITACHI
CM 4ST
C
Trigger Provided Provided
Lock Button Provided Not Provided
Trigger
Handle
Lock Button
Page 5
-2-
<Comparison of size>
Maker
Model
Item
HITACHI
CM 4ST
C
L1 mm 214 228
L2 mm 201 204
L3 mm 38 40
H mm 156 168
L3
L2
L1
H
Low vibration and noise
The rubber between the ball bearing and outer frame on both sides of the armature ensures less vibration
and noise with no load than the conventional model.
<Vibration and noise with no load (ø110 mm rim type with diamond wheel attached>
Maker
Model
Item
HITACHI
CM 4ST
C
Noise with no load m/s
2
2.0 3.7
Vibration with no load dB 87 90
Compact body
The compact body improves operability compared with the conventional model.
Smart gear cover and base
The silver-painted gear cover and glossy coated base enhance product appearance compared with the
conventional model.
<Comparison of product appearance>
Maker
Model
Item
HITACHI
CM 4ST
C
Gear cover Paint finish Shot finish
Base With gloss Without gloss
Page 6
-3-
1. Specifications
Model
Item
CM 4ST
Capacity
Max. cutting depth
34 mm (for 110 mm diamond wheel)
31.5 mm (for 105 mm diamond wheel)
Diamond wheel size
Max. diameter
110 mm external dia. x 1 mm thickness x 20 mm internal dia.
(Korea only: 15 mm internal dia.)
Type of motor AC single phase commutator motor
Type of switch Trigger switch
Enclosure
• Housing ----------------------------------- Polyamide resin
• Handle cover ---------------------------- Polyamide resin
• Gear cover ------------------------------- Die-cast aluminum alloy
• Base --------------------------------------- Steel
Full-load current and
Power input
Power input 1,300 W
Rotation speed No-load 13,000 min
-1
Net 2.9 kg (6.4 lbs.)
Weight
Gross 3.6 kg (8.0 lbs.)
Packing Corrugated cardboard box
Type Two-core cabtire cable
Cord
Overall length 2.0 m (6.6 ft.)
Standard accessories • Wrench --------------------------------------- 2
Optional accessories
• Water plug
• Rubber adapter
• Vinyl hose
• Diamond wheel
Segment type (for dry cutting) ------ Diameter 105 mm (4”)
Rim type (for wet cutting)------------- Diameter 110 mm (4”)
NOTE: The weight does not include the cord and diamond wheel.
SPECIFICATIONS
Voltage Full-load current Power input
110 V 12.4 A
120 V 11.4 A
127 V 10.8 A
220 V 6.2 A
230 V 5.9 A
240 V 5.7 A
1,300 W
SPECIFICATIONS
Page 7
-4-
L1 L2
L3
H
1. Comparison of Specifications (Superior specifications:
)
HITACHI
Maker
Model
Item
CM 4ST CM 4SB2
C
Diamond wheel dia. mm 110 (4-3/8”) 110 (4-3/8”) 110 (4-3/8”)
Max. cutting depth mm 34 (1-3/8”) 34 (1-3/8”) 34 (1-3/8”)
No-load speed min
-1
13,000 11,500 13,000
Power input W 1,300 1,320 1,300
Catalog specifications
Weight
(excluding cord)
Kg
2.9* (6.4 lbs.) 2.8* (6.2 lbs.) 2.9* (6.4 lbs.)
Voltage V 220 220 220
Speed min
-1
13,900 11,700 13,400
Noise level dB 87 85 90
No-load
Vibration level dB 106 (2.0 m/s2) 103 (1.4 m/s2) 111 (3.7 m/s2)
Current A 6.2 6.3 6.1
Speed min
-1
8,900 7,900 8,500
To rq u e N ·m
0.82
(1.11 ft-lbs.)
0.90
(1.22 ft-lbs.)
0.82
(1.11 ft-lbs.)
Full-load
Output W 770 740 730
Max. output W 1,950 2,090 1,640
Max. torque N·m
12.6
(17.1 ft-lbs.)
16.5
(22.4 ft-lbs.)
9.4
(12.8 ft-lbs.)
Characteristics
Weight
(excluding cord)
Kg
2.99*
(6.6 lbs.)
2.94*
(6.5 lbs.)
2.94*
(6.5 lbs.)
L1 mm 214 (8-27/64”) 204 (8-1/32”) 228 (8-63/64”)
L2 mm 201 (7-29/32”) 204 (8-1/32”) 204 (8-1/32”)
L3 mm 38 (1-1/2”) 28 (1-7/64”) 40 (1-37/64”)
Dimensions
Hmm
156 (6-9/64”) 156 (6-9/64”) 168 (6-39/64”)
Dust-proof structure Trigger and Button Trigger and Button Trigger
Features
Cutting depth setting Wing bolt Large lever Wing bolt
*: Excluding the cord and diamond wheel
COMPARISON WITH SIMILAR PRODUCTS
Page 8
-5-
1. Safety Instructions
In the interest of promoting the safest and most efficient use of the Model CM 4ST Cutter by all of our
customers, it is very important when concluding a sale that the salesperson carefully ensure that the buyer
seriously recognizes the importance of the Handling Instructions, and fully understands the precautions
listed on the Name Plate or Caution Plate attached to each tool.
A. Handling instructions
Although every effort is made in each step of design, manufacture, and inspection to provide protection
against safety hazards, the dangers inherent in the use of any electric power tool cannot be completely
eliminated. Accordingly, the Handling Instructions list general precautions and suggestions on the use of
electric power tools, and specific precautions and suggestions on the use of impact drills to enhance the
safe and efficient use of the tool by the customer. Salespersons must be thoroughly familiar with the
Handling Instructions in order to offer appropriate guidance to the customer during sales promotion
activities.
B. Caution on the Name Plate
Each tool is provided with a Name Plate that contains the following basic safety precautions on use of the
tool.
[For Mexico and Panama]
[For Taiwan]
C. Precautions on usage
While basic precautions on use are listed in the Handling Instructions and on the Name Plate, make sure
that the customer understands and follows the special precautions listed below.
• The Model CM 4ST is an electric power tool designed for use with water. Accordingly, it is provided with
double insulation and a special waterproofing system at the handle portion to help prevent electric shock.
However, since the effectiveness of insulation is affected by how the user operates the tool, normal tool
wear and other factors, the operator cannot be considered protected 100% against possible electric
shock. Therefore, to prevent possible serious injury, customers who frequently use water while cutting
stone, tile, masonry, and similar materials should ensure that an earth leakage circuit breaker is installed.
• Before use, carefully inspect the diamond wheel without fail. If there is any indication of cracks, bending,
or other damage, do not use the wheel.
• When using a segment type (dry cut) of diamond wheel, do not apply water or cutting fluid during cutting
operation. (Doing so will significantly shorten the service life of the diamond wheel.)
COMPARISONS WITH SIMILAR PRODUCTS
PRECAUTIONS ON SALES PROMOTION
Page 9
-6-
Cutting grain
(Diamond)
Bonding agent (BOND)
Diamond layer
Slit
Wheel base
Fig. 1
• Single-operation cutting must be restricted to cutting depths of 20 mm or less, at slow feed speed. Cutting
at deeper than 20 mm must be done in two or three separate cutting operations. Attempting single-
operation cutting at deeper than 20 mm will shorten the service life of the diamond wheel, and could
cause motor burnout.
• Zigzag, angled or curved cutting, the use of the side-face surface of the wheel, or other irregular cutting
operations will seriously shorten the service life of the diamond wheel, and must be strictly avoided.
• As cutting operation produces dust and chips, the operator should always wear protective goggles and a
dust mask.
D. Diamond wheel service life
The service life of a diamond wheel depends on the type of work, the operator’s level of skill, and the type
and quality of the diamond wheel itself. The table below shows the average service life expectancy for the
diamond wheel when used for the normal cutting of concrete. (Diamond wheels are optional accessories.)
Dry or wet Workpiece Diamond wheel Cutting depth Service life
Dry
Concrete
(Compressive strength: 240 kg/cm
2
)
105 dia. diamond wheel
(Segment type)
10 mm Approx. 200 m
Wet
Concrete
(Compressive strength: 240 kg/cm
2
)
110 dia. Diamond wheel
(Rim type)
20 mm Approx. 200 m
E. Diamond wheel
As illustrated in Fig.1, the diamond wheel consists
of a thin layer of diamond material permanently
fused to the outer circumference of the wheel
base material. The diamond layer consists of
diamond grain and its bonding agent.
F. Diamond wheel clogging
For diamond grain containing BOND, the degree of abrasion varies depending on the type of material being
cut and the cutting speed. When the cutting particles produced are large, the degree of abrasion quickly
expands, and the wheel cuts into the material very well. However, the degree of abrasion is less when the
cutting particles produced are very small, thereby reducing the effectiveness of cutting. In such case,
additional force applied in an attempt to speed up cutting will cause sparks to fly around the outer
circumference of the diamond wheel due to a phenomenon known as "clogging."
In the event of clogging, do not apply additional force. Instead, withdraw the cutting edge of the wheel from
the material, wait a moment, and then reapply the cutting edge to the material with little pressure. Then,
when effective cutting is restored, normal cutting operation can be continued. This process is known as
"dressing."
Page 10
-7-
Gear Cover [41]
Ball Bearing 606ZZC2PS2L [40]
Spindle And Gear Set [39]
Bearing Holder [38]
Ball Bearing 6002VVCMPS2L [37]
Distance Piece [36]
Bearing Cap [35]
O-Ring [34]
Seal Lock Scre
w
(W/Sp. Washer) M5 x 25 [48]
Spindle And Gear Set [39]
O-Ring [34]
Ball Bearing
6002VVCMPS2L [37]
Distance Piece [36]
Bearing Cap [35]
Bearing Holder [38]
Push
Jig
60 mm
37 mm
Fig. 3
1. Precautions on Disassembly and Reassembly
[Bold] numbers in the descriptions below correspond to item numbers in the Parts List and exploded
assembly diagram for the Model CM 4ST.
Note on disassembly: Before starting disassembly, be sure to disconnect the power plug from the power supply.
1. Removal of the diamond wheel
Remove the diamond wheel while being very careful to avoid damaging it and causing possible injury.
(Note that the Bolt (Left Hand) M7 x 15 [49] that secures the diamond wheel in place is left-hand threaded.)
2. Disassembly of the gear cover
and base (Fig. 2)
(1) Loosen the three Machine Screw
(W/Washers) M5 x 25 [20] that fasten the
Housing Ass’y [16] and Gear Cover [41],
and then remove the Gear Cover.
(2) Loosen the Wing Bolt M6 x 37 [55] that
couples the Base [52] and Gear Cover
[41], and then remove the Spring Washer
M6 [54] and Sleeve [53].
(3) Extract the Roll Pin D6 x 32 [51] that
fastens the Base [52] and Gear Cover
[41], and then remove the Base [52].
3. Disassembly of the spindle gear
(1) Loosen the two Seal Lock Screw (W/Sp.
Washer) M5 x 25 [48], and then use a
wooden or plastic hammer to gently tap on
the end surface of the Gear Cover [41] to
loosen and remove the Bearing Holder
[38], Spindle And Gear Set [39], and
related parts as shown in Fig. 3.
(2) Support the Bearing Holder [38] with an
appropriate jig, and then use a hand press
to push down on the end surface of the
spindle, to order to remove the Spindle
And Gear Set [39], Distance Piece [36],
and O-Ring [34].
CAUTION:
If the spindle must be replaced, replace
both the spindle and gear without fail.
As both parts are joined by keyless
pressure fitting, attempting to join old
and new components will reduce the
fitting strength.
REPAIR GUIDE
Disassembl
y
Gear Cover [41]
Roll Pin
D6 x 32 [51]
Base [52]
Sleeve [53]
Spring Washer M6 [54]
Wing Bolt
M6 x 37 [55]
Fig. 2
Page 11
-8-
Ball Bearing
629VVC2PS2L [43]
Washer (A) [45]
Dust Seal [8]
Ball Bearing
608VVC2PS2L [9]
Fig. 5
4. Disassembly of the armature
(Fig. 4)
(1) Use a wooden or plastic hammer to gently
tap on the end surface of the Housing
Ass’y [16], in order to loosen and remove
the Armature [47].
(2) Use a bearing puller to extract the Pinion
[42] and Ball Bearing 629VVC2PS2L [43],
and then remove Washer (A) [45] and the
Woodruff Key 2.5 x 8 [46].
(3) Finally, use the bearing puller to extract
the Ball Bearing 608VVC2PS2L [9], and
then remove the Dust Seal [8].
Reassembly can be conducted by reversing the disassembly procedures. However, special attention
should be given to the following items.
(1) Ensure that the Rubber Ring [44] is properly inserted into the bearing chamber of the Gear Cover [41].
During reassembly, be very careful not to damage the Rubber Ring [44].
(2) When only replacing the Ball Bearing 629VVC2PS2L [43] and Ball Bearing 608VVC2PS2L [9], be very
careful to ensure that Washer (A) [45] and the Dust Seal [8] are reassembled in the proper direction, as
shown in Fig. 5.
• Insert 5 g of grease (Nippeco SEP-3A, Code No.930035 recommended) into the gear chamber of the
Gear Cover [41].
• Grease the teeth of the Pinion [42] and the gear of the Spindle And Gear Set [39] (by using a brush).
• Liberally apply grease (Nippeco SEP-3A, Code No.930035 recommended) to the inner and outer
surfaces of the Rubber Ring [44] and O-Ring [34].
• Tapping Screw (W/Flange) D4 x 20 (Black) [18] ----------------------2.0 ± 0.5 N•m (20 ± 5 kgf•cm)
• Hex. Hd. Tapping Screw D5 x 65 [3] -------------------------------------3.4 ± 0.5 N•m (35 ± 5 kgf•cm)
• Machine Screw (W/Washers) M5 x 25 [20]-----------------------------3.4 ± 0.7 N•m (35 ± 7 kgf•cm)
• Seal Lock Screw (W/Sp. Washer) M5 x 25 [48] -----------------------3.9 ± 1.0 N•m (40 ± 10 kgf•cm)
• Machine Screw M3.5 (Switch [14] ) --------------------------------------0.6 ± 0.2 N•m (6 ± 1.5 kgf•cm)
Reassembl
y
Application of lubricant
Screw Tightening Torques
Ball Bearing 608VVC2PS2L [9]
Dust Seal [8]
Armature [47]
Woodruff Key 2.5 x 8 [46]
Washer (A) [45]
Rubber Ring [44]
Ball Bearing 629VVC2PS2L [43]
Pinion [42]
Fig. 4
Page 12
-9-
Fig. 7
(1) For products with noise suppressor (2) For products without noise suppressor
Switch [14]
Noise Suppressor [23]
Switch [14]
Fig. 6
(1) For products with noise suppressor
(2) For products without noise suppressor
Internal Wirin
g
Wiring Diagram
Switch [14]
Stator Ass'y [5]
Cord [29]
A
rmature [47]
Noise Suppressor [23]
A
rmature [47]
Stator Ass'y [5] Switch [14]
Cord [29]
Page 13
-10-
Upon completing reassembly after repair, measure the insulation resistance and conduct a dielectric
strength test.
Insulation resistance: 7 MΩ or more using AC 500 V megohm tester
Dielectric strength: AC 4,000 V/1 minute, with no abnormalities (220 V to 240 V)
AC 2,500 V/1 minute, with no abnormalities (110 V to 127 V)
After no-load operation for 30 minutes, the no-load current values should be as follows:
Voltage (V) 110 120 127 220 230 240
Current (A) Max. 5.0 4.4 4.6 2.7 2.6 2.7
Diamond wheel runout: Deflection of the diamond wheel must be 0.6 mm or less at the 100 mm dia. points.
Insulation Tests
No-Load Current Value
Product Accurac
y
Page 14
-11-
MODEL
Variable
Fixed
10 20 30 40 50 60 min.
Work Flow
CM 4ST
General Assembly
Handle Cover
Cord
Cord Armor
Switch
Base
Armature
Ball Bearing
608VVC2PS2L
Ball Bearing
629VVC2PS2L
Pinion
Gear Cover
Spindle And
Gear Set
Bearing
Holder
Bearing Cap
Ball Bearing
606ZZC2PS2L
Ball Bearing
6002VVCMPS2L
Housing Ass'y
Stator Ass'y
STANDARD REPAIR TIME (UNIT) SCHEDULES
Page 15
Model CM 4ST
CUTTER
LIST NO. E725
(E1)
2010 · 8 · 16
55
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
17
18
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
501
19
15
Page 16
PART
S
CM 4ST
DESCRIPTION REMARKS
1 317-758 FAN GUIDE 1
2 317-756 O-RING 1
3 960-251 HEX. HD. TAPPING SCREW D5 X 65 2
4 930-703 BRUSH TERMINAL 2
* 5 340-783C STATOR ASS'Y 110V 1 INCLUD. 4
* 5 340-783G STATOR ASS'Y 110V 1 INCLUD. 4 FOR TPE
* 5 340-783D STATOR ASS'Y 120V-127V 1 INCLUD. 4
* 5 340-783E STATOR ASS'Y 220V 1 INCLUD. 4
* 5 340-783F STATOR ASS'Y 230V-240V 1 INCLUD. 4
6 930-804 TERMINAL M4.0 (10 PCS.) 2
7 983-858 SEAL PACKING 1
8 317-757 DUST SEAL 1
9 608-VVM BALL BEARING 608VVC2PS2L 1
10 956-866 RUBBER COVER (B) 1
11 333-137 HANDLE COVER 1
12 303-328 SWITCH RUBBER COVER 1
13 305-499 MACHINE SCREW (W/WASHER) M3.5 X 6 4
14 325-531 SWITCH (1P SCREW TYPE) W/LOCK 1 INCLUD. 13
* 15 980-063 TERMINAL 2
* 15 930-804 TERMINAL M4.0 (10 PCS.) 2 FOR VEN, TPE, BRA (127V)
16 317-752 HOUSING ASS'Y 1 INCLUD.19,30
17 NAME PLATE 1
18 301-653
TAPPING SCREW (W/FLANGE) D4 X 20 (BLACK) 3
19 938-477 HEX. SOCKET SET SCREW M5 X 8 2
20 317-751 MACHINE SCREW (W/WASHERS) M5 X 25 3
21 316-394 THRUST WASHER 1
22 931-701 BEARING LOCK 1
* 23 994-273 NOISE SUPPRESSOR 1 FOR TPE,KOR
* 24 980-063 TERMINAL 2 FOR NOISE SUPPRESSOR
* 25 938-108 TERMINAL 1 FOR NOISE SUPPRESSOR
26 984-750 TAPPING SCREW (W/FLANGE) D4 X 16 2
27 960-266 CORD CLIP 1
* 28 953-327 CORD ARMOR D8.8 1
* 28 938-051 CORD ARMOR D10.1 1
* 29 500-234Z CORD 1 (CORD ARMOR D8.8)
* 29 500-474Z CORD 1 (CORD ARMOR D10.1) FOR VEN, TPE
* 29 500-423Z CORD 1 (CORD ARMOR D8.8) FOR SIN, KUW
* 29 500-468Z CORD 1 (CORD ARMOR D8.8) FOR THA
* 29 500-435Z CORD 1 (CORD ARMOR D8.8) FOR HKG
* 29 500-434Z CORD 1 (CORD ARMOR D8.8) FOR MEX, PAN (120V)
* 29 500-488Z CORD (BRA) 1 (CORD ARMOR D8.8) FOR BRA (127V)
* 29 500-487Z CORD 1 (CORD ARMOR D8.8) FOR BRA (220V)
30 958-900 BRUSH HOLDER 2
31 999-043 CARBON BRUSH (1 PAIR) 2
32 945-161 BRUSH CAP 2
* 33 956-879 WASHER (B) 1
* 33 333-125 WASHER (C) 1 FOR KOR
34 944-486 O-RING (1AP-20) 1
35 956-872 BEARING CAP 1
36 303-323 DISTANCE PIECE 1
- 2 - 8 - 10
*ALTERNATIVE PARTS
ITEM
NO.
NO.
USED
CODE NO.
ITEM
NO.
NO.
USED
CODE NO.
Page 17
PART
S
CM 4ST
DESCRIPTION REMARKS
37 600-2VV BALL BEARING 6002VVCMPS2L 1
38 333-240 BEARING HOLDER 1
39 333-241 SPINDLE AND GEAR SET 1
40 606-ZZM BALL BEARING 606ZZC2PS2L 1
41 333-126 GEAR COVER 1
42 333-242 PINION 1
43 629-VVM BALL BEARING 629VVC2PS2L 1
44 318-647 RUBBER RING 1
45 958-915 WASHER (A) 1
46 940-220 WOODRUFF KEY 2.5 X 8 1
* 47 360-900C ARMATURE 110V 1
* 47 360-900D ARMATURE 120V-127V 1
* 47 360-900E ARMATURE 220V 1
* 47 360-900F ARMATURE 230V-240V 1
48 303-327
SEAL LOCK SCREW (W/SP. WASHER) M5 X 25 2
49 303-326 BOLT (LEFT HAND) M7 X 15 1
50 956-878 WASHER (A) 1
51 949-576 ROLL PIN D6 X 32 (10 PCS.) 1
52 317-759 BASE 1
53 303-330 SLEEVE 1
54 949-455 SPRING WASHER M6 (10 PCS.) 1
55 303-331 WING BOLT M6 X 37 1
DESCRIPTION REMARKS
501 941-057 WRENCH (HEX. SOCKET 10/19.2MM) 2
DESCRIPTION REMARKS
601 303-648 WATER PLUG 1
602 956-885 RUBBER CONNECTOR 1
603 956-883 HOSE 1
* 604 321-192
DIAMOND WHEEL (SEGMENT) 106MM-D20 HOLE 1 EXCEPT FOR KOR
* 605 939-586 DIAMOND WHEEL (RIM) 100MM-D20 HOLE 1 EXCEPT FOR KOR
* 606 939-587 DIAMOND WHEEL (RIM) 110MM-D20 HOLE 1 EXCEPT FOR KOR
8 - 10 - 3 -
*ALTERNATIVE PARTS
NO.
USED
CODE NO.
ITEM
NO.
NO.
USED
CODE NO.
ITEM
NO.
OPTIONAL ACCESSORIES
NO.
USED
CODE NO.
ITEM
NO.
STANDARD ACCESSORIES
Page 18
CM 4ST
DESCRIPTION REMARKS
- 4 - Printed in Japan 8 - 10
(100816N)
*ALTERNATIVE PARTS
NO.
USED
CODE NO.
ITEM
NO.
Loading...