Hitachi 61SWX12B, 43UWX10B, 53SWX10B, 53SWX12B, 61UWX10B User Manual 2

PROJECTION COLOR TV

61SWX10B 53UWX10B 61SWX12B 61UWX10B 53SWX10B 43UWX10B 53SWX12B

OPERATING GUIDE

IMPORTANT SAFETY INSTRUCTIONS 2-4

FIRST TIME USE 5-22

THE GENIUS REMOTE CONTROL

ULTRATEC BIT-MAP ON-SCREEN DISPLAY

USEFUL INFORMATION INDEX 71-75

36-70

23-35

CUSTOMIZE

SETUP

VIDEO

AUDIO

THEATER

SEL

As an ENERGY STAR

Partner, Hitachi, Ltd. has determined that this

product meets the E

NERGY STAR

guidelines for energy efficiency.

IMPORTANT

Follow all warnings and instructions marked on this projection television.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated Òdangerous voltageÓ within the productÕs enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

NOTE: ¥ There are no user serviceable parts inside the television.

¥ Model and serial numbers are indicated on back side of the television. ¥ This television is not intended for use in a computer room.

POWER SOURCE

This projection television is designed to operate on 120 Volts 60Hz, AC current. Insert power cord into a 120 Volt 60Hz outlet.

TO PREVENT ELECTRIC SHOCK, DO NOT USE THE TELEVISION S (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NEVER CONNECT THE TELEVISION TO 50HZ, DIRECT CURRENT, OR ANYTHING OTHER THAN THE SPECIFIED VOLTAGE.

CAUTION: Never remove the back cover of the television as this can expose you to very high voltages and other

hazards. If the television does not operate properly, unplug the television and call your authorized dealer or service shop.

NOTE: This television receiver will display television closed captioning, ( or ), in accordance with

paragraph 15.119 of the FCC rules.

CAUTION:

Adjust only those controls that are covered in the instructions, as improper changes or modifications not expressly approved by HITACHI could void the userÕs warranty.

MODIFICATIONS:

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hitachi America, Ltd. Home Electronics Division may void the userÕs warranty.

SAFETY TIPS

1. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

2. When the power cord or plug is damaged or frayed, unplug the television from the wall outlet and refer servicing to qualified service personnel.

3. Do not overload wall outlets and extension cords as this can result in fire or electric shock.

4. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

5. Do not attempt to service the television yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

6. Never push objects of any kind into the televisionÕs cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the television.

7. If the television has been dropped or the cabinet has been damaged, unplug the television from the wall outlet and refer servicing to qualified service personnel.

8. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not ooperate normally, or has been dropped.

9. Do not subject your television to impact of any kind. Be careful not to damage the picture tube surface.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: ¥ Read these instructions. SAFETY POINTS YOU SHOULD KNOW ABOUT

¥ Keep these instructions. YOUR HITACHI PROJECTION TELEVISION ¥ Heed all warnings.

¥ Follow all instructions.

Our reputation has been built on the quality, performance, and ease of service of HITACHI televisions.

Safety is also foremost in our minds in the design of these units. To help you operate these products properly, this section illustrates safety tips which will be of benefit to you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your HITACHI television.

Please fill out your warranty card and mail it to HITACHI. This will enable HITACHI to notify you promptly in the improbable event that a safety problem should be discovered in your product model.

NO!

Coins

NO!

HELP

10. Clean only with dry cloth

11-1. Do not place the television on an

unstable cart, stand, or table. The television may fall, causing serious injury to a child or an adult, and serious damage to the appliance. Use only with a cart or stand recommended by the manufacturer, or sold with the television. Wall or shelf mounting should follow the manufacturerÕs instructions, and should use a mounting kit approved by the manufacturer.

11-2. Use only with the cart, stand,

tripod, bracket, or table specified by the manufacturer, or sold with the apparatues. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

FOR YOUR PERSONAL SAFETY

14. Avoid dusty places. Accumulated dust inside the chassis may cause failure of the television when high humidity persists.

15. The television has slots or openings in the cabinet for ventilation purposes which provide reliable operation of the receiver and protect the television from overheating. These openings must not be blocked or covered.

¥ Do not block any ventilation

openings. Install in accordance with the manufacturerÕs instructions.

¥ Never cover the slots or openings

with cloth or other material.

12. Do not use this apparatus near water.

¥ Never expose the television to

rain or water. If the set has been exposed to rain or water, unplug television from wall outlet and refer to qualified service personnel.

13. Choose a place where light (artificial or sunlight) does not shine directly on the screen.

NO!

TOO

HOT!

PROTECTION AND LOCATION OF YOUR TELEVISION

¥ Never block the bottom ventilation

slots of the television by placing it on a bed, sofa, rug, etc.

¥ Do not install near any heat sources

such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

¥ Never place the television near or

over a radiator or heat generator.

¥ Never place the television in a built-in

enclosure unless proper ventilation is provided.

SAFETY TIPS

PICTURE CAUTIONS

Picture Burn Prevention

¥ Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and

other fixed (non-moving) patterns can cause permanent damage to projection television receivers. Such ÒPATTERN BURNSÓ constitute misuse and are NOT COVERED by your HITACHI Factory Warranty.

¥ When using Picture-in-Picture function, the sub-picture should not be left permanently in one corner of the screen or a

ÒPATTERN BURNÓ may develop over a long period of time.

Public Viewing of Copyrighted Material

Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require prior authorization from the broadcaster or owner of the video program material.

PROTECTION AND LOCATION OF YOUR TELEVISION

16-1. If an outside antenna is connected

to the television, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, NFPA No. 70-1975, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit connection to grounding electrode, and requirements for the grounding electrode.

16-2. Note to CATV system installer:

(Only for television with CATV reception). This reminder is provided to call the CATV system installerÕs attention to Article 82040 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

17. An outside antenna system should not be located in the vicinity of overhead power lines or other electrical lights or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

18. For added protection for the television during a lightning storm, or when it is unused for long periods of time, unplug it from the wall outlet and disconnect antenna. This will prevent damage due to lightning and power-line surges.

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE INSTRUCTIONS.

19. This television should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply at your home, consult your dealer or local power company.

20. If the television does not operate normally by following the operating instructions, unplug the television from the wall outlet and refer servicing to qualified service personnel. Adjust only those controls that are covered in the instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified service technician to restore the television to normal operation.

OPERATION OF YOUR TELEVISION

Use Proper Voltage

21. If your television is to remain unused for a period of time, (such as when going on a holiday), turn the television OFF and unplug it from the wall outlet.

22. If you are unable to restore normal operation by following the detailed procedure in your operating instructions, do not attempt any further adjustments. Unplug the television and call your dealer or service technician.

IF THE TELEVISION DOES NOT OPERATE PROPERLY

23. Whenever the television is damaged or fails, or if there is a distinct change in performance that indicates a need for service, unplug the television and have it checked by a qualified service technician.

24. It is normal for some televisions to make occasional snapping or popping sounds, particularly when being turned on or off. If the snapping or popping is continuous or frequent, unplug the set and consult your dealer or service technician.

25. Do not use attachments not recommended by the television manufacturer as they may cause hazards.

FOR SERVICING AND MODIFICATION

26. If replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

27. Upon completion of any service or repairs to the television, ask the service technician to perform routine safety checks to determine that the television is in safe operating condition.

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

GROUNDING CONDUCTORS

POWER SERVICE GROUNDING ELECTRODE SYSTEM

NEC NATIONAL ELECTRICAL CODE

(NEC PART 250 PART H)

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

No !

Service

Snap

Pop

Snap

ask me!

ACCESSORIES

1. Remote Control Unit CLU-5711TSI (Part No. HL01641), or Remote Control Unit CLU-5713TSI (Part No. HL01643).

2. Two ÒAAÓ size, 1.5V batteries (For Remote Control Unit).

REMOTE CONTROL BATTERY INSTALLATION AND REPLACEMENT

1. Open the battery cover of the remote control by pushing the notched part of the cover with your fingers and pulling the cover off.

2. Insert two new ÒAAÓ size batteries for the remote control. When replacing old batteries, push them towards the springs and lift them out.

3. Match the batteries to the (+) and (-) marks in the battery compartment.

4. Replace the cover.

BOTTOM VIEW

Lift up on tab to remove back cover.

Check to make sure you have the following accessories before disposing of the packing material.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace with the same or equivalent type.

PART NAME

PART NO. ILLUSTRATION

43" TELEVISION

STAND

SP-43W

(Not included,

order separately)

OPTIONAL

H530052

CUSTOM HITACHI TELEVISION STAND

Excellent for VCR and video-tape storage. Special features include smoked glass doors and an adjustable shelf. Available in shark grey.

CAUTION: Television stand model SP-43W is designed for use with a 43 inch or smaller television set. Use of a smaller

stand, a non Hitachi recommended stand or a generic stand may result in instability, causing possible injury.

POWER

VCR

CBL

DVD

LAST CHSLEEP

HELP

EXIT

CHVOL

MUTE

PIP PIP CH

SWAP

FREEZE

PIP MODE

PIP ACCESS

PROG

TV/VCR

SLOW

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

STATUS

INFO

VCR PLUS+

SVCS

GUIDE/TV

SCHD

VID 1

VID 2

VID 3

VID 4

VID 5

AV2

AV1

AV3

PIX

CLU-5711TSI

CLU-5711TSI 1.

CLU-5713TSI 1.

POWER

VCR

CBL

DVD

LAST CHSLEEP

HELP

EXIT

CHVOL

MUTE

PIP PIP CH

SWAP

FREEZE

PIP MODE

PIP ACCESS

PROG

TV/VCR

SLOW

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

STATUS

INFO

VCR PLUS+

SVCS

GUIDE/TV

SCHD

VID 1

VID 2

VID 3

VID 4

VID 5

TAPE

AMP

MODE

CLU-5713TSI

HOW TO SET UP YOUR NEW HITACHI PROJECTION TV

CAUTION: Magnetic fields, such as those of external speakers, may cause the picture to distort if they are placed too

close to the television. Move the magnetic field source away from the television until there is no picture distortion.

4' MINIMUM

10'

15'

BEST HORIZONTAL

VIEWING ANGLE

20'

ANTENNA

Unless your TV is connected to a cable TV system or to a centralized antenna system, a good outdoor color TV antenna is recommended for best performance. However, if you are located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient.

LOCATION

Select an area where sunlight or bright indoor illumination will not fall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the perforated back cover of the set. To avoid cabinet warping, cabinet color changes, and increased chance of set failure, do not place the TV where temperatures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc.

VIEWING

The major benefit of the HITACHI Projection Television is its large viewing screen. To see this large screen at its best, test various locations in the room to find the optimum spot for viewing.

The best picture is seen by sitting directly in front of the TV and about 10 to 18 feet from the screen. Picture brightness decreases as the viewer moves to the left and right of the receiver.

During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the reflection or the TV can be located in a different section of the room.

If the TVÕs audio output will be connected to a Hi-Fi systemÕs external speakers, the best audio performance will be obtained by placing the speakers equidistant from each side of the receiver cabinet and as close as possible to the height of the picture screen center. For best stereo separation, place the external speakers at least four feet from the side of the TV, place the surround speakers to the side or behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker placement for best performance.

10'

15'

BEST

VERTICAL VIEWING

ANGLE

20'

HOOK-UP CABLES AND CONNECTORS

Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shielded wire. Cables can be purchased from most stores that sell audio/video products. Below are illustrations and names of common connectors. Before purchasing any cables, be sure of the output and input connector types required by the various components and the length of each cable.

300-Ohm Twin Lead Connector

This outdoor antenna cable must be connected to an antenna adapter (300-Ohm to 75-Ohm).

Phono Connector

Used on all standard video and audio cables which connect to inputs and outputs located on the televisionÕs rear jack panel and front control panel.

’’F’’ Type 75-Ohm Coaxial Antenna Connector

For connecting RF signals (antenna or cable TV) to the antenna jack on the television.

S-VIDEO (Super Video) Connector

This connector is used on camcorders, VCRs, and laserdisc players with an S-VIDEO feature in place of the standard video cable to produce a high quality picture.

ANTENNA CONNECTIONS TO REAR JACK PANEL

VHF (75-Ohm) antenna/CATV (Cable TV)

When using a 75-Ohm coaxial cable system, connect the outdoor antenna or CATV coaxial cable to the ANT A (75-Ohm) terminal. If you have a second antenna or cable TV system, connect the coaxial cable to the ANT B terminal.

VHF (300-Ohm) antenna/UHF antenna

When using a 300-Ohm twin lead from an outdoor antenna, connect the VHF or UHF antenna leads to screws of the VHF or UHF adapter. Plug the adapter into the antenna terminal on the TV.

When both VHF and UHF antennas are connected

Attach an optional antenna cable mixer to the TV antenna terminal, and connect the cables to the antenna mixer. Consult your dealer or service store for the antenna mixer.

To outdoor antenna or CATV cable

To second antenna or cable system

Antenna mixer

ANT A/ANT B

To UHF Antenna

To outdoor antenna or CATV system

To outdoor VHF or UHF antenna

FRONT PANEL CONTROLS

FRONT VIEW

a MENU/SELECT button

This button allows you to enter the MENU, making it possible to set TV features to your preference without using the remote. This button also serves as the SELECT button when in MENU mode.

b INPUT/EXIT button

Press this button to select the current antenna source, VIDEO: 1, 2, 3, 4, 5 or alternate antenna source. Your selection is shown in the top right corner of the screen. This button also serves as the EXIT button when in MENU mode.

c CHANNEL selector

Press these buttons until the desired channel appears in the top right corner of the TV screen. These buttons also serve as the cursor down (H) and up (G) buttons when in MENU mode.

d VOLUME level

Press these buttons for your desired sound level. The volume level will be displayed on the TV screen. These buttons also serve as the cursor left (F) and right (E) buttons when in MENU mode.

e POWER button

Press this button to turn the TV on or off.

Models: 61SWX10B, 61SWX12B, 53SWX10B, 53SWX12B

INPUT 3

S-VIDEO

VIDEO

AUDIO

L/MONO

EXIT

INPUT

SELECT

MAGIC FOCUS

VOL- VOL+ CH- CH+

CURSOR

INPUT 3

S-VIDEO

VIDEO

AUDIO

L/MONO

EXIT

INPUT

SELECT

MAGIC FOCUS

VOL- VOL+ CH- CH+

CURSOR

e fgh

e f

POWER

PUSH

POWER

PUSH

Models: 61UWX10B, 53UWX10B, 43UWX10B

NOTES: Your remote control does not have an INPUT button. To change to video inputs, press VID1~VID5 buttons depending

on your choice (see page 23).

FRONT PANEL CONTROLS

f POWER light

You will see a red light when the TV is turned on.

g PERFECT PICTURE sensor

The Perfect Picture sensor will make automatic picture adjustments depending on the amount of light in the room to give the best picture. (see page 57)

h REMOTE CONTROL sensor

Point your remote at this area when selecting channels, adjusting volume, etc.

i MAGIC FOCUS

Use this button to adjust your picture quality to optimum performance.

j FRONT INPUT JACKS (for VIDEO: 3)

Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantly view your favorite show or new recording. Press the INPUT button until VIDEO: 3 appears in the top right corner of the TV screen. If you have mono sound, insert the audio cable into the left audio jack.

NOTES: 1. Your HITACHI Projection TV will appear to be turned OFF if there is no video input when VIDEO: 1, 2, 3, 4 or 5 is

selected. Check the Power Light to make sure the TV is turned off when not in use.

2. To see an auto-demonstration of the on-screen displays with HELP text displayed, press and hold the POWER button on the TV set for approximately five seconds. Press the POWER button on the TV again to end the autodemonstration.

FRONT PANEL JACKS AND CONNECTIONS

The front panel jacks are provided as a convenience to allow you to easily connect a camcorder or VCR as shown in the following examples:

NOTE: 1. Completely insert connection cord plugs when connecting to front panel jacks. If you do not, the played back picture

may be abnormal.

2. If you have a S-VHS VCR, use the S-INPUT cable in place of the standard video cable.

3. If you have a mono VCR, insert the audio cable into the left audio jack of your TV.

REAR PANEL JACKS

a Antenna Input/Output

The remote control allows you to switch between two separate 75-Ohm RF antenna inputs, ANT A and ANT B. ANT A input can be displayed as a main picture or sub-picture. ANT B can only be displayed as a main picture. (ANT B cannot be displayed as a sub-picture.) The antenna output labeled ÒTO CONVERTERÓ allows the ANT A connection to pass directly to a different source such as a cable box, only when ANT B is displayed as a main picture.

b Audio/Video Inputs 1, 2, 4 and 5

The VID1~VID5 buttons will select each video source each time they are pressed. Use the audio and video inputs to connect external devices, such as VCRs, camcorders, laserdisc players, DVD players etc. (If you have mono sound, insert the audio cable into the left audio jack.)

c MONITOR OUT

These jacks provide fixed audio and video signals which are used for recording. Use the S-VIDEO Output for high quality video output.

d AUDIO TO HI-FI Output

These jacks provide variable audio output to a separate stereo amplifier. With this connection, the audio to the stereo can be controlled by the televisionÕs main volume.

e S-VIDEO Inputs 1 and 2

Inputs 1 and 2 provide S-VIDEO (Super Video) jacks for connecting equipment with S-VIDEO output capability.

AUDIO TO HI-FI

STOP

CONNECT ONLY 8 OHM SPEAKERS

DO NOT SHORT CIRCUIT THESE TERMINALS (Such damage is NOT COVERED by your television warranty)

REAR SPEAKER

SUB WOOFER

OPTICAL

INPUT

COAXIAL

INPUT

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

AUDIO TO HI-FI

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

NOTE: You may use VIDEO or S-VIDEO inputs to connect to INPUT 1 and 2, but only one of these inputs may be used at a

time.

NOTE: S-VIDEO Output may be used for recording, only when the input is of S-VIDEO type.

Models: 61UWX10B, 53UWX10B,

43UWX10B

Models: 61SWX10B, 61SWX12B

53SWX10B, 53SWX12B

REAR PANEL JACKS

f Component: Y-P

BPR

Inputs

Inputs 4 and 5 provide Y-P

BPR

jacks for connecting equipment with this capability, such as a DVD player or Set Top Box. You may

use standard video signal for INPUT:4 and 5.

Items g ~ j are for 53/61SWX10B and 53/61SWX12B only.

g REAR SPEAKER Output Terminals

These terminals are used to connect external speakers, which are used for the surround sound feature. The volume level is controlled by the televisionÕs main volume. These speaker output terminals can be turned on and off in the THEATER-SPEAKER SETUP menu. Use speakers with 8-Ohm impedance only.

h Optical Input

This jack provides high quality audio input from a Dolby Digital DVD player or HDTV Set Top Box. Use a digital optical cable to connect your TV to a compatible device. This input can be used for VIDEO: 4 or VIDEO: 5 audio, as selected in the THEATERINPUT SOURCE menu. (see page 68)

i Coaxial Input

This jack provides high quality audio input from a Dolby Digital DVD player or HDTV Set Top Box. This input can be used for VIDEO: 4 or VIDEO: 5 audio, as selected in the THEATER-INPUT SOURCE menu. (see page 68)

j SUB WOOFER Output

This jack provides variable audio output to a sub-woofer accessory. With this connection, the audio can be controlled by the televisionÕs main volume. This feature can be turned on and off in the THEATER-SPEAKER SETUP menu.

NOTES: 1.

DO NOT connect standard VIDEO and S-VIDEO to Input 1, 2 or 3 at the same time. S-Video has a higher priority over video input.

2. When using the Y-PBPRinput jacks, connect your components audio output to the TVÕs Input 4 or 5 Left and Right Audio input jacks.

If your component has a Coaxial Out or Optical Out, use these connectors in place of the standard Audio L/R output jacks.

3. Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TVÕs PBinput and

the components R-Y output to the TVÕs PRinput.

4. Your component outputs may be labeled Y-CBCR. In this case, connect the component CBoutput to the TVÕs PBinput and the

component CRoutput to the TVÕs PRinput.

5. It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPR inputs. (See page 56)

6. To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the Y-PBPRjacks.

7. This TVÕs optical digital input jack fully complies with the international standard governing this type of jack (IEC958), and is designed

for connection to a Dolby Digital (AC-3 or PCM) DVD Player or Dolby Digital (AC-3 or PCM) HDTV Set Top Box. Older equipment, some of which is not fully compliant with IEC958, may not be compatible with the Dolby Digital bitstream. Such a connection using anything other than Dolby Digital AC-3 or PCM bitstream could create a high noise level, causing damage to your speakers.

AUDIO TO HI-FI

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

DVD Player

Stereo System Amplifier

Laserdisc player, VCR, camcorder, etc.

VCR #2

Cable TV Box

Optional, see tips on page 15

VCR #1

Outside antenna or cable TV coaxial cable

2-Way signal splitter

Optional, see tips on page 15

OUTPUT

Y P

L R

HDTV Set-Top Box

V L R

OUTPUT

S-VIDEO

ANT IN

OUTPUT

S-VIDEO

VL R

OUTPUT

B/CBPR/CR

L R

INPUT

Optional, see tips on page 15

V L R

INPUT

S-VIDEO

INPUT

OUTPUT

REAR PANEL CONNECTIONS

NOTE: 1.

Connect only 1 component to each input jack.

2. Follow connections that pertain to your personal entertainment system.

3. Standard video signal (composite video) can be input to all video inputs. (Video 1 ~ VIdeo 5).

TYPICAL FULL-FEATURE SETUP

(43/53/61UWX10B MODELS)

FIRST TIME USE

AUDIO TO HI-FI

STOP

CONNECT ONLY 8 OHM SPEAKERS

DO NOT SHORT CIRCUIT THESE TERMINALS (Such damage is NOT COVERED by your television warranty)

REAR SPEAKER

DVD Player

Stereo System Amplifier

Laserdisc player, VCR, camcorder, etc.

VCR #2

Cable TV Box

Optional, see tips on page 15

VCR #1

Outside antenna or cable TV coaxial cable

2-Way signal splitter

Optional, see tips on page 15

OUTPUT

Y P

L R

HDTV Set-Top Box

V L R

OUTPUT

S-VIDEO

ANT IN

OUTPUT

S-VIDEO

VL R

OUTPUT

B/CBPR/CR

L R

INPUT

Sub Woofer

INPUT

Optional, see tips on page 15

Surround Speakers

See connections on page 15

V L R

INPUT

S-VIDEO

INPUT

OUTPUT

OPTICAL

INPUT

COAXIAL

INPUT

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

SUB WOOFER

NOTE: 1.

Connect only 1 component to each input jack.

2. Follow connections that pertain to your personal entertainment system.

3. Standard video signal (composite video) can be input to all video inputs. (Video 1 ~ VIdeo 5).

TYPICAL FULL-FEATURE SETUP

(53/61SWX10B AND 53/61SWX12B MODELS)

TIPS ON REAR PANEL CONNECTIONS

S-VIDEO connections are provided for high performance laserdisc players, VCRs etc. that have this feature. Use these connections in place of the standard video connection if your device has this feature.

If your device has only one audio output (mono sound), connect it to the left audio jack on the television.

Refer to the operating guide of your other electronic equipment for additional information on connecting your hook-up cables.

A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output (INPUT: 1 in the example on page 13 or 14). Refer to your VCR operating guide for more information on line input-output connections.

You may use VIDEO or S-VIDEO inputs to connect to Input 1 or Input 2, but only one of these may be used at a time.

Connect only 1 component (VCR, DVD player, camcorder, etc.) to each input jack.

COMPONENT: Y-PBPR (Input 4 &5) connections are provided for high performance components, such as DVD players and settop-boxes. Use these connections in place of the standard video connection if your device has this feature.

Your component outputs may be labeled Y, B-Y, and R-Y. In this case, connect the components B-Y output to the TVÕs PBinput and the components R-Y output to the TVÕs PRinput.

Your component outputs may be labeled Y-CBCR. In this case, connect the components CBoutput to the TVÕs PBinput and the components CRoutput to the TVÕs PRinput.

You may use standard video signal for INPUT:4 and 5.

It may be necessary to adjust TINT to obtain optimum picture quality when using the Y-PBPRinputs. (See page 56)

To ensure no copyright infringement, the MONITOR OUT output will be abnormal, when using the

Y-PBP

jacks.

REAR SPEAKER TERMINAL CONNECTIONS

CONNECT AFTER TURNING THE POWER TO THE TV OFF.

(Rear speaker connection applies to SWX model only)

Press the Right Speaker red button and insert the positive (+) lead wire into the hole next to the button. Once the wire is in place, pull the red button back to original position and the wire is locked into place. In the same manner, press the Right Speaker black button and insert the negative (-) lead wire. Repeat this procedure for the Left Speaker.

CAUTION: Do not short speaker terminal, (do not connect a wire directly across any two terminals). This could cause

damage to your audio outputs or other damage to your TV.

CAUTION: Do not connect speakers simultaneously to the REAR SPEAKER terminal of the Projection TV and an external

amplifier. This could damage both the TV and the speakers. Your TV was designed to use 8-Ohm speakers only. Any other type may degrade the audio performance of your entertainment system.

REAR SPEAKER

Projection T.V.

Speaker

Amplifier

TO EXTERNAL SPEAKER

CONNECTING EXTERNAL AUDIO SOURCES

AUDIO TO HI-FI

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

INPUT

Stereo System Amplifier

To Audio Input Terminal

of External Amplifier

CONNECTING EXTERNAL AUDIO AMPLIFIER

To control the audio level of an external audio amplifier with the remote control, connect the system as shown below.

NOTE: To prevent damage to the speaker and distorted sound, set the volume control of the audio amplifier lower and adjust

the sound using the remote control of the TV set.

REAR PANEL OF TELEVISION

AUDIO TO HI-FI

STOP

CONNECT ONLY 8 OHM SPEAKERS

DO NOT SHORT CIRCUIT THESE TERMINALS (Such damage is NOT COVERED by your television warranty)

REAR SPEAKER

SUB WOOFER

OPTICAL

INPUT

COAXIAL

INPUT

Stereo System Amplifier

To Audio Input Terminal

of External Amplifier

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

Models: 61UWX10B, 53UWX10B,

43UWX10B

Models: 61SWX10B, 61SWX12B

53SWX10B, 53SWX12B

FIRST TIME USE

Match the numbers below to the diagrams for speaker placement and refer to the table on page 18 for the different surround sound requirements. (See pages 65-67 for SURROUND functions.)

a The televisionÕs internal speakers. b The televisionÕs internal center channel speaker, which is on only when the television is in SURROUND-STADIUM, SURROUND-

ROCK ARENA, SURROUND-JAZZ CLUB, SURROUND-PRO LOGIC, or SURROUND-DOLBY DIGITAL mode.

c These speakers are connected to a separate audio amplifier. Use the AUDIO TO HI-FI output on the TV. d These speakers are connected to a rear speaker 8-Ohm output on the TV. e This sub woofer is connected to the SUB WOOFER output on the TV.

L R

STEREO SYSTEM AMPLIFIER

L R

OUT

SUB WOOFER

Models: 61SWX10B, 61SWX12B

53SWX10B, 53SWX12B

FIRST TIME USE

SURROUND REQUIRED OPTIONAL EFFECT

FEATURE CONNECTION CONNECTION

OFF 1 3 5 Receive mono and stereo sound.

STADIUM 1 2 4 3 5 Listener has feeling of being at a stadium.

ROCK ARENA 1 2 4 3 5 Listener has feeling of being at a rock concert.

JAZZ CLUB 1 2 4 3 5 Listener has feeling of being at a jazz club.

DOLBY 1 2 4 3 5 Movie theater reproduction, with separate left,

PRO LOGIC center, right, and surround channels.

DOLBY DIGITAL 1 2 4 5 3 To be used with a DVD player or HDTV Set Top

Box with Dolby Digital output. This provides up to 6 channels of all-digital surround sound. There are 3 full-range channels for the front (FL, C, FR) plus separate, full-range left and right surround channels (SL, SR). The sixth channel is Low Frequency Effects for a sub woofer (SW), supplying those room-shaking rumbles experienced in the best movie theaters.

When left and right speakers are connected (3), the internal speakers (1) can be disabled, creating better separation between left, center and right channels. The center channel audio will be heard from (2), this speaker cannot be disabled.

Models: 61SWX10B, 61SWX12B

53SWX10B, 53SWX12B

CONNECTING EXTERNAL VIDEO SOURCES

The exact arrangement you use to connect the VCR, camcorder, laserdisc player, DVD player, or HDTV Set Top Box to your TV set is dependent on the model and features of each component. Check the owner’s manual of each component for the location of video and audio inputs and outputs.

The following connection diagrams are offered as suggestions. However, you may need to modify them to accommodate your particular assortment of components and features. For best performance, video and audio cables should be made from coaxial shielded wire.

Before Operating External Video Source

The input mode is changed every time the VID1~VID5 button is pressed as shown below. Connect an external source to the INPUT terminal, then press the VID1~VID5 button as necessary to view the input source. (See page 26)

(ANTENNA)

(INPUT)

VID1

ANT

Ant A

Video:1

VID1

CONNECTING A MONAURAL AUDIO SOURCE TO INPUT1~INPUT5

1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below.

2. Connect the cable from the AUDIO OUT of the VCR or the laserdisc player to the INPUT (MONO)/L(AUDIO) jack.

3. Press the VID1~VID5 button to view the program from the VCR or the laserdisc player. The VIDEO mode disappears automatically after approximately eight seconds.

4. Press the ANT button to return to the previous channel.

NOTE: When the TV is set to VIDEO and a video signal is not received from the VIDEO INPUT JACK on the back panel of the

TV (i.e., VCR/laserdisc player, etc. is not connected or the video device is OFF), the set will appear to be OFF.

AUDIO TO HI-FI

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

RLR

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

Hitachi Model or

Similar Model

VIDEO OUTAUDIO OUT

VCR

Back of VCR

AUDIO TO HI-FI

STOP

CONNECT ONLY 8 OHM SPEAKERS

DO NOT SHORT CIRCUIT THESE TERMINALS (Such damage is NOT COVERED by your television warranty)

REAR SPEAKER

SUB WOOFER

OPTICAL

INPUT

COAXIAL

INPUT

Hitachi Model or

Similar Model

VIDEO OUTAUDIO OUT

VCR

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

RLR

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

Back of VCR

Models: 61UWX10B, 53UWX10B,

43UWX10B

Models: 61SWX10B, 61SWX12B

53SWX10B, 53SWX12B

INPUT MODE SELECTION ORDER

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A STEREO SOURCE TO INPUT1~INPUT5

1. Connect the cable from the VIDEO OUT of the VCR or the laserdisc player to the INPUT (VIDEO) jack, as shown on the TV set below.

2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.

3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.

4. Press the VID1~VID5 button to view the program from the VCR or laserdisc player. The VIDEO icondisappears automatically after approximately eight seconds.

5. Press the ANT button to return to the previous channel.

AUDIO TO HI-FI

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

Back of VCR

V L R

VCR

OUTPUT

Hitachi Model or

Similar Model

NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

2. A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot record its own video or line output. (INPUT: 1 in example on page 13 or 14) Refer to your VCR operating guide for more information on line input-output connections.

AUDIO TO HI-FI

STOP

CONNECT ONLY 8 OHM SPEAKERS

DO NOT SHORT CIRCUIT THESE TERMINALS (Such damage is NOT COVERED by your television warranty)

REAR SPEAKER

SUB WOOFER

OPTICAL

INPUT

COAXIAL

INPUT

Back of VCR

V L R

VCR

OUTPUT

Hitachi Model or

Similar Model

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

Models: 61UWX10B, 53UWX10B,

43UWX10B

Models: 61SWX10B, 61SWX12B

53SWX10B, 53SWX12B

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING AN S-VIDEO SOURCE TO INPUT 1, 2 AND 3

1. Connect the cable from the S-VIDEO OUT of the VCR or the laserdisc player to the INPUT (S-VIDEO) jack, as shown on the TV set below.

2. Connect the cable from the AUDIO OUT R of the VCR or the laserdisc player to the INPUT (AUDIO/R) jack.

3. Connect the cable from the AUDIO OUT L of the VCR or the laserdisc player to the INPUT (AUDIO/L) jack.

4. Press the VID1~VID3 button to view the program from the VCR or laserdisc player. The VIDEOicon disappears automatically after approximately eight seconds.

5. Press the ANT button to return to the previous channel.

AUDIO TO HI-FI

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

Hitachi Model or

Similar Model

Rear Panel of Television

VCR or Laserdisc Player

V L R

OUTPUT

S-VIDEO

See tips on Page 15

NOTES: 1. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is

played back will be abnormal if the connection is loose.

Back of VCR

AUDIO TO HI-FI

STOP

CONNECT ONLY 8 OHM SPEAKERS

DO NOT SHORT CIRCUIT THESE TERMINALS (Such damage is NOT COVERED by your television warranty)

REAR SPEAKER

SUB WOOFER

OPTICAL

INPUT

COAXIAL

INPUT

Hitachi Model or

Similar Model

Rear Panel of Television

VCR or Laserdisc Player

V L R

OUTPUT

S-VIDEO

See tips on Page 15

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

Back of VCR

Models: 61UWX10B, 53UWX10B,

43UWX10B

Models: 61SWX10B, 61SWX12B

53SWX10B, 53SWX12B

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING A COMPONENT SOURCE TO VIDEO 4 OR 5: Y-PBPR.

1. Connect the cable from the Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (Y) jack, as shown on the TV set below.

2. Connect the cable from the CB/PBOUT or B-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PB)jack.

3. Connect the cable from the CR/PROUT or R-Y OUT of the Laserdisc/DVD player or HDTV set top box to the INPUT (PR) jack.

4. Connect the cable from the AUDIO OUT R of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/R) jack.

5. Connect the cable from the AUDIO OUT L of the Laserdisc/DVD player or HDTV set top box to the INPUT (AUDIO/L) jack.

6. Press the VID4~VID5 button, to view the program from the Laserdisc/DVD player or HDTV set top box. The VIDEO icon disappears automatically after approximately eight seconds.

7. Press the ANT button to return to the previous channel.

AUDIO TO HI-FI

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

Rear Panel of Television

OUTPUT

R/CR PB/CB

L R

AUDIO

VIDEO

DVD Player

Hitachi Model or

Similar Model

Back of DVD Player

OUTPUT

L R Y P

HDTV Set-Top Box

NOTE: 1. You may use standard video signal for INPUT:4 and 5.

2. Completely insert the connection cord plugs when connecting to rear panel jacks. The picture and sound that is played back will be abnormal if the connection is loose.

3. See page 15 for tips on REAR PANEL CONNECTIONS.

4. If your device is conected to INPUT 4 component jacks, make sure to select VID4-OPTICAL from the THEATER-

INPUT SOURCE menu. If it is connected to INPUT 5 component jacks, make sure to select VID5-OPTICAL from the THEATER-INPUT SOURCE menu.

AUDIO TO HI-FI

STOP

CONNECT ONLY 8 OHM SPEAKERS

DO NOT SHORT CIRCUIT THESE TERMINALS (Such damage is NOT COVERED by your television warranty)

REAR SPEAKER

SUB WOOFER

OPTICAL

INPUT

COAXIAL

INPUT

Rear Panel of Television

OUTPUT

R/CR PB/CB

L R

AUDIO

VIDEO

DVD Player

Hitachi Model or

Similar Model

Back of DVD Player

OUTPUT

L R Y P

HDTV Set-Top Box

MONITOR

OUT

INPUT 1

AUDIO

(MONO)

AUDIO

S-VIDEOS-VIDEO

VIDEO

AUDIO

(MONO)

S-VIDEO

VIDEO

Y/VIDEO

AUDIO

RLR

Y/VIDEO

AUDIO

INPUT 2 INPUT 4 INPUT 5

(MONO) (MONO)

ANT A

TO CONVERTER

ANT B

OPTICAL

OUT

OPTICAL

OUT

Models: 61UWX10B, 53UWX10B,

43UWX10B

Models: 61SWX10B, 61SWX12B

53SWX10B, 53SWX12B

THE GENIUS REMOTE CONTROL

In addition to controlling all the functions on your HITACHI Projection TV, the new remote control is designed to operate different types of VCRs, CATV (Cable TV) converters, set-top-box, satellite receiver, DVD players, and other audio/video equipment with one touch. Basic operation keys are grouped together in one area.

To operate your TV, point the remote control at the remote sensor of the TV and press the TV button. The TV button will blink, indicating that the remote will now control your television.

To operate your VCR, point the remote at the remote sensor of the VCR and press the VCR button. The VCR button will blink, indicating that the remote will now control your VCR. (See page 30 for instructions on how to program the remote to control your VCR.)

To operate your cable box, point the remote at the remote sensor of the cable box and press the CABLE (CBL) button. The CBL button will blink, indicating that the remote will now control your cable box. (See page 31 for instructions on how to program the remote to control your cable box.)

To operate your set-top-box or satellite receiver point the remote at the remote sensor of the set-top-box and press the SET-TOPBOX (STB) button. The STB button will blink, indicating that the remote will now control your set-top-box. If you have a satellite receiver, use this button to prorame your satellite receiver. (See page 32 for instructions on how to program the remote to control your set-top-box.)

To operate your DVD player, point the remote at the remote sensor of the DVD player and press the DVD button. The DVD button will blink, indicating that the remote will now control your DVD player. (See page 33 for instruction on how to program the remote to control your DVD player.)

To operate additional audio/video equipment, point the remote at the remote sensor of the component you wish to control and press the AV1, AV2 or AV3 button. This button will blink, indicating that the remote will now control the desired component. (See page 34 for instructions on how to program the remote to control additional Audio/Video equipment.)

a These buttons allow the remote to control your TV, VCR,

cable box, satellite receiver, DVD player, or other Audio/Video equipment depending on which mode is chosen, as explained above.

b,c LIGHT BUTTON

When you are in a dark room, press the light button b on the remote to light up the buttons shown in c and the source button will blink. The light will stay on for about 8 seconds if the light button is not pressed again. These buttons will not appear to light if the room is too bright.

POWER

VCR

CBL

DVD

LAST CHSLEEP

HELP

EXIT

CHVOL

MUTE

PIP PIP CH

SWAP

FREEZE

PIP MODE

PIP ACCESS

PROG

TV/VCR

SLOW

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

STATUS

INFO

VCR PLUS+

SVCS

GUIDE/TV

SCHD

VID 1

VID 2

VID 3

VID 4

VID 5

AV2

AV1

AV3

PIX

CLU-5711TSI

POWER

VCR

CBL

DVD

LAST CHSLEEP

HELP

EXIT

CHVOL

MUTE

PIP PIP CH

SWAP

FREEZE

PIP MODE

PIP ACCESS

PROG

TV/VCR

SLOW

SOURCE WIZARD

REC

SELECT

C.C.

ASPECT

STB

ANT

STATUS

INFO

VCR PLUS+

SVCS

GUIDE/TV

SCHD

VID 1

VID 2

VID 3

VID 4

VID 5

TAPE

AMP

MODE

CLU-5713TSI

NOTE: 1. Your remote control ÒSOURCE WIZARDÓ buttons

are either labeled as ÒAV1, AV2 and AV3,Ó or ÒCD, TAPE, and AMP.Ó If your remote control ÒSOURCE WIZARDÓ buttons are labeled as ÒAV1, AV2, and AV3,Ó please program your Audio/Video components as follow for best performance. Use ÒAV1Ó to program your CD brand. Use ÒAV2Ó to program your TAPE brand, and use ÒAV3Ó to program your AMPLIFIER/RECEIVER brand.

AV1-Use for CD brand AV2-Use for TAPE brand AV3-Use for AMPLIFIER/RECEIVER brand.

2. Your remote control button to directly access the THEATER MODE is either labeled as ÒPIXÓ or ÒMODEÓ.

AV2

AV1

AV3

DVD

SOURCE WIZARD

+ 53 hidden pages