Hitachi 32CX38B Operating Manual

Download

Page 1

SOLID STATE COLOR TV

OPERATING GUIDE

IMPORTANT SAFEGUARDS

FIRST TIME USE

THE REMOTE CONTROL

COLOR GRAPHIC GUIDE

_K USEFUL INFORMATION

INDEX

2-5

6-19

20-31

32-49

50-55

Page 2

IMPORTANT

Follow all warnings and instructionsmarked on this color television.

A o,u,,o,RISK OF ELECTRIC SHOCK lJ

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol, within an equilat-

eral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclo- sure that may be ofa sufficientmagnitude to constitute a risk of electric shock to parsons.

_IL The exclamation point within an equilateral triangle, is

intended to alert the user to the presence of important oper- ating and maintenance (servicing) instructions in the litem- tun) accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE

THIS COLOR TELEVISION TO RAIN OR MOISTURE.

NOTE: • There are no user serviceable parts inside the television. I

• Model and serial numbers are indicated on back side of the television.

CAUTION: • Adjust only those controls that are covered in the instructions, as improper

changes or modifications not expressly approved by Hitachi could void the user's authority to operate the TV.

POWER SOURCE

This HITACHI color television is designed to operate on 120 volts 60Hz, AC current. Insert power cord into a 120 volt 60Hz outlet.

TO PREVENT ELECTRIC SHOCK, DO NOT USE THE TELEVISION'S (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NEVER CONNECT THE TELEVISION TO 50HZ, DIRECT CURRENT, OR ANYTHING OTHER

THAN THE SPECIFIED VOLTAGE.

NOTE: This television receiver will displaytelevision closed captioning,(r_ or _), inaccordance I

with paragraph 15.119 of the FCC rules.

I,/_ CAUTION: Never remove the backcover of the televisionas this can expose you to veryhighvoltages and other

hazards. If the television does not operate properly,unplug the television and call your authorized dealer or service shop.

Page 3

IMPORTANT '

IMPORTANT SAFEGUARDS

CAUTION: SAFETY POINTS YOU SHOULD KNOW ABOUT

• Read allof theseinstructions. YOUR HITACHI TELEVISION RECEIVER

• Savethese instructionsfor lateruse.

• Followallwarningsand instructionsmarked onthe television receiver.

Our reputation has been built on the quality, performance, and ease of service of HITACHI lele_sk_ receivers.

Safety is also foremost in our minds in the design of tbese units. To help you operofe these products propedy, thb section iitustrates safety tips which witl be of benefit 1o you. Please read it carefully and apply the knowk_lge you obtain from it to _ proper operation of your HITACHI television receiver.

Please fill out your warranty card and mail it to HITACHI. This will enable HITACHI to notify you promptly in the improbable event that a safely problem should be discovered in your product model.

FOR YOUR PERSONAL SAFETY

1. This television set is equipped with a polar-

ized aitemating-current line plug (a plug hav- ing one blade wider than the other.) This plug will fit into the power out_ only orm way. This is a safety feature. If you am unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit. contact your electrician to replace your obsolete out- let. Do not defset the safety purpose of the polarized plug.

2. When the puwer cord or plug is damaged or frayed, unplug the television sel from the wall outlet and'refer "servicing to qualified service personnel.

3. Do cot overinad wall ce,.,tlotsand exlor_don co_dssethis cannm_dlintin)_ eler_vk'-a_ock.

4. Do notalow anythingto faston or rolloverItm puwer cord, and do not plecothe TV where the puwer cord Is _=iect to trat6cor abuse. Thismay resultin a shockorfirehazard.

5. Do not attempt to service the television set yourself as opening or removing covers may expose you to dangerous voltage or other

hazards. Refer all servicing to qualified ser-

vice personnel.

6. Never push objects of any kind into the televi-

sion's cabinet slels as they may touch dan- gerous voltage po_ts or short out parts thai

could result in a itm or electric shock. Never spill liquid of any kind on the tekwision set.

If the television ast bas be_ dropped or the cabinet bas been dem89ed, unplug the tele- vision set from the wall outlet and refer ser- vicing to quaJ_led smica personnel

If liquidhas bsenspilledintothe television sat, unplugitImm the waltoutletend refer serviceto qualifiedsen/icepersormel.

Do notsubjectyoortek_sk_nsetto impactof

anykTnd. Becare_ notto dwnagethe pin- turetubesudace.

10.Unpluglhetolavisinnastfrontthewalloullel

bokxadserQng.Usaadempclomforclean-

DOnotuse liquidorsem-ol cleaners.

11-1.

Do not piece the lelevision sat on an unsta- ble e_rt. aanch or t_de. The tolevl_on sal may fd. causk_9 asdous injury to a shlld or an =Klul, end sadous demage to the appi- ance. Use only _ a cart or stand recom- mended by the menofastumr, o¢suld with the televisisn sat. Wd _r shelf moanting should follow the manufec_er's instructions, and

should use a mount_ kit approved by the menutaoturer.

11-2. An applkmce and cart c_nldnetion should

be moved with care. Quick slopu, exceseive force, and uneven surface= may cause the appliance and cart combination to overturn.

PROTECTION AND LOCATION OF YOUR SET

12. Do nOt use the television set near water, for

example, near a batMub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. •

Neverexposethe setto rain or water. If the sethasbaen oxpu_mdtorainorwater,unplug astfromwaltoutlet andreferto qualifiedser- vicepersonnel.

13. _ a place where light (a_clel or sun-

light) doel nct shkHI directly on It_ sumen.

14, Avoiddustyl_m_m,_nce accumulateddust

imdcle_ ch_sle may cause fellureofthe set whenhighhumiditypersists.

15. Tba sot hse sk_ll or openings in the cabinet

for ventilation purposes which provide mlleble

operl_on of tba recelver and profect the TV from overhseti_. "l_sa openings musl not

ba _ or covered.

• Never cover the slotsor opening_swith cloth

orothermaterial.

• Near blockthebottomverdktionskis of the

astby pax._gitona ded,sofa,n_g,e_.

• Neuerpiecethesat riserorovora mdlatoror

h_t mgleter,

• N_er l_a_ th_ _ in a b,D,-in anck_,n, unlesa _ ve,_la_on is l_ded.

Page 4

PROTECTION AND LOCATION OF YOUR SET

16-1. If en outldde antenna iscontracted to lhe _ set, be sure the

enmnna _n b gn)unckKl so ,,- to l_ovkfa l=me _ against voltuge mJrgas and bullt up _UIIC cha_ge_ Section 810 of the National Electrical Code, NFPA No. 70-1975, provides infarma- tion wire re_mDct to proper 9roundlnO of the mest and supporting structure, grounding of the lead-in wife to an antemm discharge unit, size ol grounding conductors, location of antenna discharge unk connection to grounding electrode, and requirements for the grounding electrode.

NIECmno_L BICTA_4L CCOE

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE INSTRUCTIONS.

16-2.

Note to CATV syslbom instaile_.

(Only for t_ev*_on sets with CATV rec,p_n) This remlndor is provtd_l to _ CAW system

installers attention to Artic_ 820-40 of the NEC

that provides guidelines Io4, proper grounding

encLinpanicu_r,speciesthatthecabfa7ou_

shait be connect,,d to tbe grounding syslem ol

the bullding, as cioee to the point ol cab_ entry as practical

17. An outside enlenna syslem shotdd not be iccat- KI in me vtciclty of ovedwad power llm_ or om_ elestdcal fights or power clrcuits, or where it can fall into such power lines or drcuits.

installing an outside antenna syslem, extreme

cam should be taken to keep _ touching such

power lines or circuits as contact _ them might

be fatal

18. For added pro*,ention for the tefavislon s<Ndudng

a llghtn[ng storm, or wben it is lelt unmtendod and uoused fo¢ long pedodo ol time, unplug il

from the wall outlet and dlL_:onnenl entwtna. This will Wevent damage due to llghln_g pov_rdine surges.

IMPORTANT

OPERATION OF YOUR SET 20.

19. "rbetelevisionset ll_ou_l be opemtm_onlyfrom tbe typeof poweresurse Indicaled_ the mark*

inglab,d.If youare notsureof tbe type ofpow_

st.5)plyel your homo, consul your television ciceis( c_ localpower €omplmy. For teim4_en sets dosign,d to opeme Irom battery power.

referto theoperatingin_icns.

Ifthetekwis_onsetdoesrm operatenormalyby _ow_O U,eo_erat_ _stn_:be._u_ the

tefaVcdon_ fromIbe walloul_t and mf_r ser- ving _oqu_r_d m_c, p_mnn_ Adju_ oNy Ihose o_ofa Ifm am covered ic the Ol_ml_g

_mc_ns m _prol_r adlu_n_nt of omercon- troismayresullin dl_nageand will of_n require extensive work by a qualified technician to restorethe televisionset to nonmdoperation.

21. If your t_evisicn _ is to remain unused for a period of time, (suct_ as wben goicg on a holidoy), turn the televfidon set OFF and unplug it 1ram Ibe

wall outkR.

IF THE SET DOES NOT OPERATE PROPERLY

22. If you are unable to restore normal operalicn by

fallowS10 tht diCe|led procedure in your oplrat{_lg

do not attempt any furmer adjust-

ments. Unplug tbe se_end callyour doak_ or ser- vicetechnician.

23. Wbenever the tefavislon set is damaged or falis, or H there is a distinct cl'mnge in perfom_nce that indicates a need for service, unplug the set and have it checked by a professional service technician.

24. It is normal for some television s_s to make occasional snapping or poW, n0 sounds, partlcu-

isrty when being turned on or oIL If me enapplng

popping is continuous or frequent, unplug the

set end consult your dealer or service technician.

FOR SERVICING AND MODIFICATION

_'_. Do not use attm:tu_ents not moommemisd by _

tek_llk_ _ m_ufac_r_ as they ml_ cause hazards.

26. wr, en _ parta ara raqulrad, be muro U'm ser'vice tachr_¢Jar) hall _ r_lnl I_ltl akoeddfad by tbe rnanufectumr _m beva, tbe m_e'ne ct'_arastadstk= as the orioicel pr,n. substituticns may rasult In lira, elentric sho_, o_ other hazardL

27. Ui)on mmp_icn ol any mm,_, o_rap,ira to th, tefa'_sicn set,esk tbe mrvk_ tashnic_n to i_r- form routinesefaty d'_Kd_to delen_ thai the tekwkdonisin sefa opiating oondllion.

Page 5

PICTURE CAUTIONS

WARNING

Continuous On-Screen Displays such as video games, stock market quotations,

computer generated graphics, and other fixed (non-moving) patterns can cause per- manent damage to Color Television

Receivers. Such "PATTERN BURNS" con-

stitute misuse and are NOT COVERED by

your HITACHI Factory Warranty.

When using the Picture-in-Picture function, the sub-picture should not be left permanently

in one comer of the screen or a "PATTERN BURN" may develop over a long period of time.

This color television receiver was intended mainly for the private viewing of programs broadcast by TV stations, cable companies, and programs from other video sources.

Public viewing may require prior authorization from the broadcaster or owner of the video program.

Page 6

ACCESSORIES

Check that you have the following accessories before disposing of the packing material.

1. Remote Control Unit (See Part No. below.)

2. Two "AA"size, 1.5V battedes (For Remote Control Unit).

For information regarding how to obtain these accessories, please call TOLL FREE 1-800-448-2244 for your nearest HITACHI Authodzed Parts Distdbutor in the continental United States. For Alaska and Hawaii, please contact your nearest HITACHI regional office.

PART NAME PART NO. ILLUSTRATION

CLU-418U

REMOTE TRANSI_I-I'ER

32V TELEVISION STAND

SP316B

(Not included, order separataly)

32V TELEVISION STAND

HL00234

H530022

rE]

0000

CLU418U

CUSTOM HITACHI

TELEVISION STAND

Excellentfor VCR and

videotape storage. Special

features include curved

SP317B

(Not included, order separately)

H530023

(upgrade)

smoke glass doors and

an adjustable shelf.

Available in black.

CAUTION: Television stand models SP316B and SP317B are designed for use only with a 32 inch or I

smaller television seL Use of a smaller stand, a non Hitachi recommended stand or a genedc

stand may result in instability,causing possible injury.

Page 7

REMOTE CONTROL BATTERY INSTALLATION

AND REPLACEMENT

1. Open the battery coverof the remotecontrol by push-

ingthe notched part of the cover withyour fingers.

2. Insert two new =AA" size batteries in the remote.

When replacing old batteries, push them towards the springs and liftthem out.

3. Match the batteries to the (+) and (-) marks in the battery compartment.

4. Replace the cover.

BO'rTOM VIEW

CAUTIONS

1. If your television set is to remain unused tor a long period of time, for instance, when you go on vacation,

unplug the television from the wall outlet.

2. Do not subject the remote control to shocks such as dropping it on the floor, etc. Precision parts may be damaged.

3. Do not allow the remote control to become wet and avoid placing it in areas of high humidity. Do not leave it on or near a heater. Excess heat or moisture may cause the unit to cease operation.

4. If the batteries become exhausted, remote control operation may become erratic or stop altogether. Replace

the old batteries with new "AA" (SUM-3) types.

NOTES:

1. The CHANNEL NO., VOLUME, and OFF TIMER indicators are not displayed simultaneously.

2. To operate your TV, point the remote control at the remote sensor of the TV.

Page 8

HOW TO SET UP YOUR NEW HITACHI COLOR TV

ANTENNA

Unless yourTV is connected to a cable TV system or toa centralized antenna system, a good outdoor color TV anten- na is recommended for best performance. However, if youare located in an exceptionally good signal area that is free from interference and multiple image ghosts, an indoor antenna may be sufficient.

LOCATION

Select an area where sunlight or bright indoor illuminationwill notfall directly on the picture screen. Also, be sure that the location selected allows a free flow of air to and from the back cover of the set.

To avoid cabinet warping, cabinet colorchanges, and increased chance of set failure, do not place the TV where tem- peratures can become excessively hot, for example, in direct sunlight or near a heating appliance, etc.

VIEWING

The major benefit of the HITACHI Color Television is its large viewing screen. To see this screen at its best, test var- ious locations inthe room to find the best spotfor viewing. The drawings give several suggestions.

The best picture is seen by sitting directly in front of the TV and about 6 to 9 feet from the screen. During daylight hours, reflections from outside light may appear on the screen. If so, drapes or screens can be used to reduce the

reflection or the TV can be located in a different section of the room.

If the TV's audio output will be connected to a Hi-Fi system's extemal speakers, the best audio performance will be

obtained by placing the speakers equidistant from each side of the receiver cabinet and as close as possible to the

height of the picture screen center. For best stereo separation, place the extemal speakers at least 4 feet from the

side ofthe television. Place the surroundspeakers to the side or behind the viewing area. Differences in room sizes and acoustical environments will require some experimentation with speaker placement for best performance.

4' MINIMUM

I _CAUTION:

The magnetic field of extemal speakers may cause the picture to distort if the speakers are I

placed too close to the television. Move the speakers away from the TV until there is no

picture distortion.

Page 9

HOOKUP CABLES AND CONNECTOR

Most video/audio connections between components can be made with shielded video and audio cables that have phono connectors. For best performance, video cables should use 75-Ohm coaxial shieldedwire. Cables can be pur- chased from most stores that sell audio/video products. Below are illustrationsand names of common connectors. Before purchasing any cables, be sure of the output and inputconnector types required by the various components. Also make sure the cables are the correct length.

300-Ohm Twin Lead Connector This outdoor antenna cable must be connected to an antenna adapter (300-Ohm to 75-Ohm).

"F" Type 75-Ohm Coaxial Antenna Connector

For connecting RF signals (antenna or cable TV) to the

antenna jack on the television.

--=.<DO

Phono Connector Used on all standard video and audio cables whichcon- nect to inputs and outputs located on the television's rear jack panel and front control panel.

S-Video (Super Video) Connector This connectoris used oncamcorders, VCRs and laser- disc players with an S-Video feature in place of the standard video cable to produce a high quality picture.

ANTENNA CONNECTIONS These sets are equipped with one VHFAJHF antenna terminal. The VHFAJHF terminal can be used for normal TV, cable TV (CATV), a TV game, etc.

1. VHF(75-Ohm) antenna/CAW When using a 75-Ohm coaxial cable system, disconnect the VHF adaptor from the VHF 75-Ohm receptacle and connect the outdoor antenna or CATVcable to a VHF 75-Ohm receptacle.

To outdoor antenna or CAW cable

VHF/UHF

Coaxial Cable

3. When both VHIFand UHFantennaa are connected

Attachan optional ANTENNA MIXER to the TV antenna terminal and connect the cables to the

ANTENNA MIXER.

(RearofTVset) VHF/UHF

Toou oo,

ToUHFAntenna VHFAntenna

t .t

MIXER

2. VHF (300-Ohm) antenna/UHF antenna When using a 300-Ohm twin lead from an outdoor antenna disconnect the (VHF or UHF) indoor antenna leads from screws ofthe (VHF or (UHF)

adaptor and connect outdoor (VHF or UHF) leads to these screws ofa (VHF or UHF) adaptor.

t Tooutdoor VHF

or UHF Antenna

_. IL (connect)

_1 I_._F Adapt°r

Notes:

1. If an outdoor antenna/CAW is used, disconnect the indoor antenna. Ghosting and poor reception

may result if boththe indoor and outdoor antennas CATV are connected atthe same time.

2. Consult your dealer or service store for the

ANTENNA MIXER and (VHF or UHF) adaptor.

3. The special converter (decoder) will be supplied by the cable company.

Page 10

FRONT PANEL CONTROLS

FRONT VIEW

I ! II

HOW TO OPEN THE DOOR

(_ RemoteConl_l

InfraredSensor

on _ m1. Push --_.

2. Pull the door toward the front to open it,

FRONT INPUT JACKS

I JNPUTZ I

0 0 0

0 ® ®

O0 0

J I I I I I

MENU < I_ • • See pages 22 and 24 for

I ! I I MENU, CURSOR, and EXIT

EXIT_ CURSOR button operations.

Page 11

FRONT PANEL CONTROLS

_ INPUrTSelector

Press this button to select the current antenna source or VIDEO: 1, 2 or 3. Your selection is shown at the top right corner of the screen.

(_) VOLUME Level

Press these buttons for your desired sound level. The volume level will be displayed on the TV screen.

(_ CHANNEL Selector

Pressthese buttonsuntilthe desiredchannelappearsat thetop rightcomeroftheTV screen.

(_ POWER Button

Press this button to tum the TV on or off.

NOTE:

Your HITACHI TV will appear to be tumed OFF if there is no video input when VIDEO: 1, 2, or 3 is

selected. If you have no inputto VIDEO: 1, 2 or 3, pressthe INPUT button until the normal broadcast

• picture appears. (See page 22.) If the picture does not appear, the power is OFF.

(_ REMOTE CONTROL INFRARED Sensor

Point your remote control at this area when selecting channels, adjusting volume, etc.

(_ FRONT INPUT JACKS

Use these audio/video jacks for a quick hook-up from a camcorder or VCR to instantlyview your favorite show or new recording. (Press the INPUT button until VIDEO: 3 appears in the top rightcomer of the screen.)

I NOTE: Front panel control CURSOR operation will not operate the FAMILY FAVORITES channel function. I

Page 12

FRONT PANEL JACKS AND CONNECTIONS

The front panel jacks are provided as a convenience to allowyou to easily connect a camcorder or VCR as shown in the following examples:

VkJeoCamera VideoCamera _

OUTPUT

Insert audiocable

intoleftchannel

for monosound

I INPUT

o_22__

OUTPUT

INPUT

(BackofVCR)

NOTE:

Completely insert the connection cord plugs when connecting to front panel jacks. If you do not, the picture that is played back may be abnormal.

Page 13

::lEAR PANEL JACKS

VHF/UHF

AUDIO to HI-FI OUTPUT t3)

TERMINALS

INPUT TERMINALS Q

TONR

_UOIO AUO_O AUDIO

S-VIDEO

Q VHFIUHF ANTENNA TERMINAL

(_ S-VIDEO INPUT

(_ Antenna Inputs

The VHF/UHF terminalcan be usedfor normalTV,cableTV (CATV),a TV game,etc.

Q AudioNideo Inputs 1, 2, 3

The INPUT buttonwillstepthrougheachvideosourceandthecurrentantennainputeachtimeitis pressed.Use the audioand video inputsto connectextemal devices,suchas VCRs, camcorders,laserdiscplayers,video

games,etc.

(_) Audio to Hi-Fi

These jacks provide variable audio output to a separate stereo system amplifier. With this connection, the audio to the stereo can be controlled by the television's remote control. Use these jacks for the SURROUND Left and

Right channels. (See pages 16 and 19.)

(_ S-Video

Input 1 provides S-Video (Super Video) jacks for connecting equipment with S-Video output capability.

TIPS ON REAR PANEL CONNECTIONS

The S-Video connection is provided for high pedormance laserdisc players, VCRs etc., that have this feature. Use this connection in place of the standard video connection ifyour device has this feature.

If your device has only one audio output (mono sound), connect it to the left audio jack on the TV.

Refer to the operating guide of your other electronic equipment for additional information on connecting your hookup cables.

A single VCR can be used for VCR #1 and VCR #2, but note that a VCR cannot read its own video or line output (INPUT: 1 inthe example on page 15). Refer to your VCR operating guide for more information on line input-output connections.

Page 14

REAR PANEL JACKS

REAR VIEW

l I

---"-- UDIO to HI-FI OUTPUT (_) TERMINALS

INPUT TERMINALS(_)

VHF/UHF

(_) ANTENNA

TERMINAL

(_) S-VIDEO

INPUT

Page 15

REAR PANEL CONNECTIONS

__ Outsideantennaor

cableTVcoaxialcable

_ _-_"2-way signalsplitter

O ====== O

0 ====o 0

0 r=-q r-_qoo 0

C) IlllllIliHI C)

Stereo System Amplifier

optional,seeUps

v L R onpagel3.

Laserdiscplayer,VCR, _ "_

camcorder,etc.

S-VHS V L R

VCR#1

Typical fullfeature set-up. Followconnections that pertain to yourpersonal entertainment system.

Page 16

EXTERNAL CONNECTIONS

CONNECTING EXTERNAL AUDIO AMPLIFIER

To control the audio level of an extemal audio amplifier with the remote control, connect the system as shown below.

(REAR OF TV SET)

AUDIO TO HI-FI TERMINAL

TO AUDIOINPUTTERMINAL_._(

OFEXTERNALAMPLIFIER

AUDIO

TO HI-FI

f _

II • _'_ • Q,-"',

EXTERNAL AUDIO AMPLIFIER

EXTERNAL

SPEAKERS SPEAKERS

NOTE:

To prevent damage to the speaker and distorted sound, set the volume control of the audio amplifier I lower and adjust the sound using the remote control of the TV set.

Page 17

CONNECTING EXTERNAL VIDEO SOURCES

The exact arrangement you use to connect the Video Cassette Recorder, Video Disc Player andVideo Camera to your

TV set is dependent on the model and features of each component. Check the owner's manual of each component

for the location of video and audio inputs and outputs.

The following connection diagrams are offered as suggestions. However, you may need to modify them to accom-

modate your particular assortment of components and features. For best performance, video and audiocables should be made from coaxial shielded wire.

Before Operating External Video Source The input mode ischanged every time the INPUT button is pressed as shown below. Connect extemal source to the

INPUT terminal, then press the INPUT button as necessary to view the inputsource. (See page 22.)

INPUT MODE SELECTION ORDER

NOTE:

When the TV is set to VIDEO and a video signal is not received from VIDEO INPUT JACK on the jack panel of the TV (i.e., VCPJVideo Disc Player, etc. is not connected or the video device is OFF), the screen will be grey-blue.

CONNECTING MONAURAL AUDIO VCR OR VIDEO DISC PLAYER

1. Connectthe cablefromthe VIDEO OUT of theVCR or the Video DiscPlayerto the INPUT (VIDEO)jackon the

TV setbelow.

2. Connect the cable from the AUDIO OUT of the VCR or the Video Disc Player to the INPUT (MONO)/L(AUDIO)

jack.

3. Press the INPUT button to view the program from the VCR or Video Disc Player. The VIDEO mode disappears

automatically after approximately eight seconds.

4. Press the INPUT button to return to the previous channel.

VCR

"IVINPUT

TERMINAL

INPtn

_OEO

_}1

/uUolO

,., ,,

MDEOOUT ALIOlOOUT

II I I

Page 18

CONNECTING EXTERNAL VIDEO SOURCES

CONNECTING STEREO VCR OR STEREO VIDEO DISC PLAYER

1. Connect the cable from the VIDEO OUT of the VCR or the Video Disc Player to the INPUT (VIDEO) jack on the

"IV set below.

2. Connect the cable from the AUDIO OUT R of the VCR or the Video Disc Player to the INPUT(AUDIO/R) jack.

3. Connect the cable from the AUDIO OUT L of the VCR or the Video Disc Player to the INPUT(AUDIO/L) jack.

4. Press the INPUT button to view the program from the VCR or Video Disc Player. The mode VIDEO disappears

automatically after approximately eight seconds.

5. Press the INPUT button to retum to the previous channel.

"iV INPUT

TERMINAL

iNPUt

VIDEO

NJDIO

VCR

I, '0,--',, ,/

, , ,)

'_ QUI" !U_O Ot.ff

II I I

0®®®

B_'WR

TV INPUT

"rERMIN/U.

S, ==lo

HrrAcl.g MODEL VT-ST$1A er _egbr meal

NOTE:

Completely insert the connection cord plugs when connecting to rear panel jacks. The picture that is played back will be abnormal if the connection is loose.

If you have an S-VHS VCR, use the S-INPUT cable in place of the standard video cable.

A single VCR can be used forVCR #1 and VCR #2, but note that a VCR cannot record itsown video or

line output. (INPUT: 1 in example on page 15.) Refer to your VCR operating guide for more informa-

tion on line input-outputconnections.

Page 19

AUDIO SYSTEM SET-UP

Match the numbers below to the diagram for speaker placement and refer to the table for the differentsurround sound requirements. (See page 48 for SURROUND functions.)

(_The television's intemal speakers.

(_ These speakers are connected to a separate audio amplifier. Use the Audio to Hi-Fi output on the TV.

.... .oo.o°°..°....o...o ....... .o°°_

s :ol

SURROUND

FEATURE

REQUIRB)

CONNECTION

(9 0

EFFECT

OFF Receive mono and stereo sound.

SIMULATE Atmono input, sound will be louder.

Atstereo input, sound of musicwill be louder.

MUSIC (_ (_) -- Surround channel added to left and rightaudio

amplifier speakers. Movie theater reproduction, surround channel

MOVIE (_ (_) - added to left and dght audio amplifier speakers.

Page 20

THE REMOTE CONTROL (CLU-418U)

In addition tocontrolling all the functionson your HITACHI Color TV, the new remote controlis designed to operate dif- ferent types of VCRs, CATV (Cable TV), and satellite converters with one touch. Basic operation keys are grouped

together in one area.

To operate your TV, point the remote control at the remote sensor of the TV and pressthe TV button. The remote will now control your TV.

To operate your VCR, point the remote at the remote sensor of the VCR and press the VCR button. The remote will now control your VCR. (See page 28 for instructionson how to program the remote to control your VCR.)

To operate your cable/satellite box, pointthe remote at the remote sensor of the cable/satellite box and press the CABLE button. The remote will nowcontrolyour cable/satellite box. (See page 30 for instructionson howto program

• /

the remote to control your cableisatelhte box.)

HOME

HELP THEATER TVNCR

PIP _ F_

VOL CH

Q( G Q (?D (D

(X) (D (D

INPUT SLEEP

OQO

HITACHI

CLU-418U

O ®

Thesebuttonsallowthe remotetocontrolyourTV, VCR, or cable/satellitebox dependingon which modeischosen,asexplainedabove.

TV/VCR Button When the remote is inthe TV or VCR mode, this is the TV/VCR button. When the remote is in the CABLE/SATELLITE mode, this isthe A/B button.

(_ PRECODED VCR Buttons

These buttonsalways transmit the chosenprecoded VCR codes.

HELP Button

Press this button ifhelp is needed to change menu

settings, and our context-sensitive Help system will provide explanations and/or directions for whatever function your cursor is on at that time.

HOME THEATER Button

This button allows direct access to the SUR-

ROUND functions.

Page 21

,HOW TO USE THE REMOTE TO CONTROL YOUR TV

A detailed explanation of the circled numbers follows on page 22 to 24.

HOME

HELP THEATER TVNCR

_CD

LST-CH

HITACHI

CLU-418U

Page 22

(_TV POWER Button

HOW TO USE THE REMOTE TO CONTROL YOUR TV

Press this button to tum the TV set on or off. If ON/OFF TIMER is set, it will be displayed when the TV is first tumed on. (See page 42.)

SLEEP Button Press this button to display the SLEEP TIMER inthe lower leftcomer of the screen. Every subsequent press of

this button will add 15 minutes to the timer, up to a maximum of three hours.

MENU, CURSOR Buttons All On-Screen Display features can be set or adjusted by using these buttons.

The MENU button will start the On-Screen Display.

The CURSOR buttons will highlightfunctions or adjust and set different features. Pressing the cursorbuttons will also give you access to the FAMILY FAVORITES CHANNELS On-Screen Display.

CHANNEL SELECTOR Buttons

Enter two or three numbers to select channels. Enter 0 first for channels 1 to 9. For channels 100 and above,

press the "1" button and wait for two seconds before pressing the last two digits of the channel. Channel selection may also be performed by pressing CH up (A) or down (V).

You may also use these buttons for channel scanning. Press and hold the CH up (A) ordown (V) buttons and the TV will start quickly scanning through the channels. Release the CH up (A) ordown (V) buttonswhen the TV scans to the channel you wish to watch and the TV willtune to that channel.

I NOTE:

The TV may notreceivesomechannelsifyouare notinthe correctSIGNALSOURCE mode. (See

page35.)

(_) INPUT Button

The INPUT button will select between the antenna signal and the video input jacks each time the button is pressed. If the Picture-in-Picture (P-in-P) is on, the INPUT will not select any source signal on the main picture. However, ifthe P-in-P is on, the INPUT will aitemate between the main signal source and the input source on the sub-picture. (See picture below and page 25.)

INPUT

I _IDEO:I

(S-|N)

INPUT

VIDEO:2

Page 23

HOW TO USE THE REMOTE TO CONTROL YOUR TV

(_ VOLUME, MUTE Buttons

Press the VOLUME up (A) or down (V) button until you obtain the desired sound level.

To turn the sound off instantly to answer the telephone, etc., press the MUTE button. Press the MUTE button again or press the VOLUME up (A) buttonto restore the sound.

ST_EOJ_ I

"MUTE" will remain displayed if the CLOSED CAPTION feature is tumed off.

=MUTE" will not be displayed if the CLOSED CAPTION feature is on.

Q LAST CHANNEL (LST-CH) Button

Use this button to select between the last two channels viewed. (Good for watching two sporting events, etc.)

LST-CH

STEREO 39

(_ PICTURE-IN-PICTURE

See page 25 for a description.

Page 24

HOW TO USE THE REMOTE TO CONTROL YOUR TV

(_ HOME THEATER Button

Press the HOME THEATER buttonto directly access the SURROUND function. (See page 48.)

(_ EXIT/RECALUCOMMERCIAL SKIP (CS) Button

Press this button when no menu is displayed, when you want to check the channel being received, or if it has stereo (ST) or second audio (SAP).

You can also check the time, CHANNEL ID, and if the SLEEP TIME has been set.

When in MENU mode, this button will exit all On-Screen Displays.

Press this button twice quickly, when no menu is displayed, to enable the COMMERCIAL SKIP (CS) function. This will tune the TV to the last channel viewed and after 30 seconds, tune back to the original channel.

AudioSelected

_f / Channeland

._ AntennaSource

STEREO 31 I

N_ _ Audio

Broadcast

ONT1MER_ ='ON 7:00 AM

_i ,OFF 9:00 PM 10:15 i1:

OFF TIMERr I I oo,o.oon I

TIME

If a video inputis used:

VIDEO:I

(S-IN)

/ V'_leo Input

When an S-Video

inputisconnected

You can also use the RECALL button to quicklyclear many ofthe other On-Screen Displays.

Page 25

PICTURE-IN-PICTURE (PIP) _ ;S_

The Picture-in-Picture feature is convenient when you want to watch more than one program at the same time. You can watch a TV program while viewing a VCR program (TV or tape) on the video inputs.

I? o71

Bac_ ogVCR

AUDIO/VIDEO INPUT

HOME

HELP THEATER TVNCR

( ) ( )

PIP sw_ o

MOVE FRZ

®,®

(_ P-IN-P Button

Press the PIP button and a sub-picture appears in one comer of the screen. Press the button a second time to remove the sub-picture from the screen. The TV channelwill always be either the main pictureor the sub-picture.

Main Picture

J PIP STEREO _---_-"

PIP

Sub-Picture

SWAP Button

If you wish to switch what is being shown on the main picture to the sub-picture, press the SWAP button.

PIP STEREO

ST/SA L

[

PIP

Page 26

PICTURE-IN-PICTURE

(_ MOVE Button

To move the sub-pictureto any location of the screen, press the MOVE buttononce andquickly press the CURSOR buttons.

MOVE CURSOR

To move the sub-picture to another comer, press the MOVE buttontwice quickly. The sub-picture moves one step

counterclockwise every time the MOVE button is pressed twice.

MOVE

(_ FREEZE (FRZ) Button

If you wish to freeze the sub-picture, press the FRZ button. This is convenient when trying to write down the

address for a mail order company, recordingstatistics for a sporting event, etc. To retum the picture to motion, press the same button again.

(_ FREEZE (FRZ) Button (without a sub-picture (PIP OFF))

Press this button without a sub-picture to freeze the pictureyou are currently viewing. Press this button again to retum to normal viewing. The SWAP buttonwill not work with this FREEZE function.

FRZ

AUTION: A pattem bum may develop ifthe sub-picture is left inthe same comer permanently, if the PIP

feature is used frequently, occasionally move the sub-picture to a different comer.

NOTE:

1. Onlysoundfromthe mainpicturecanbeheard.

2. Picture-in-PicturewillnotworkwithaCHILDLOCKchannelasthe mainpicturebutwillbedisplayed

as a sub-picture.

3. When the PIP buttonispressed,thesub-picturewillappearinthe samepositionaspreviouslyset.

Page 27

USING THE REMOTE TO CONTROL VCR FUNCTIONS

A detailed explanation of the circled numbers follows on page 28.

INPUT SLEEP

HITACHI

CLU-418U

Page 28

Operating the precoded function for your VCR

This remote is designed to operate different types of VCRs.

system of your VCR. (Refer to page 31.)

USING THE REMOTE TO CONTROL VCR FUNCTIONS

You must first program the remote to match the remote

Tum onyourVCR.

Aimthe remotecontrolat the frontofyourVCR.

Pressthe VCR buttontoswitchtothe VCR precodedmode.

While holding down the VCR button on the remote, enter the two digit preset code that matches your VCR as shown on page 31. The remote will turn off your VCR when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your VCR. Ifthe VCR does not turn off after five seconds, try

a different two digit preset code.

5. The remote will now control your VCR.

NOTES:

1. If your VCR cannot be operated after performing the above procedures, your VCR code has not been precod-

ed into the remote.

2. Inthe unlikelyevent that yourVCR cannotbeoperatedafterperformingthe aboveprocedures,pleaseconsult

yourVCR operatingguide.

3. The remotecontrolwillrememberthecodesyouhaveprogrammedinuntilthebatteriesareremovedfrom the remotecontrol. Afterreplacingthebatteriesrepeattheentireprogrammingprocedurestatedabove.

4. If your VCR doesnothavea powerfunction,the remotewillissuetheCHANNELUP (A) function.

VCR Button This allows the remote to control your VCR by setting it to VCR mode.

(_ PRECODED VCR Buttons

These buttons transmit the chosen precoded VCR codes. For some VCRs, you must pressthe RECORD button

twice to record a program.

(_ EXCLUSIVE TV Buttons

These buttons are for operating the TV.

I NOTE: Refer to the instruction manual of the VCR for operation of the buttons exclusively for the VCR.

Page 29

USING THE REMOTE TO CONTROL CABLE/SATELLITE BOX FUNCTIONS

I I

A detailed explanation of the circled numbers follows on page 30.

REC PAUSE

HITACHI

CLU.,418U

Page 30

USING THE REMOTE TO CONTROL CABLE/SATELLITE

BOX FUNCTIONS

Operating the precoded function for your cable/satellite box.

This remote isdesigned to operate different types of cable boxes and Digital Satellite Systems. You mustfirst program the remote to match the remote system in yourcable/satellite box. (Refer to page 31.)

1. Turn on your cable/satellite box.

2. Aim the remote control at the front of your cable/satellite box,

3. Press the CABLE button to switch to cable/satellite box mode.

4°

While holding down the CABLE button, enter the two digit preset code that matches your cable/satellite box as shown on page 31. The remote will tum off your cable/satellite box when the correct two digit preset code is entered. When this occurs, the remote control is programmed for your cable/satellite box. If the cable/satellite box does not tum off after five seconds, try another two digit preset code.

5. The remote will now control your cable/satellite box.

NOTES:

1. If your cable/satellite box cannot be operated after performing the above procedures, your cable/satellite box

code has not been precoded into the remote.

2. In the unlikely event that your cable/satellite box cannot be operated after performing the above procedures,

please consult your cable/satellite box operating guide.

3. The remote control will remember the codes you have programmed in untilthe batteries are removed from the remote control. After replacing the batteries, repeat the entire programming procedure stated above.

4. If your cable/satellite box does not have a power function,the remote will issue the CHANNEL UP (&) function.

CABLE Button This button allows the remote to control your cable/satellite box by setting itto CABLE/SATELLITE mode.

PRECODED CABLE/SATELLITE BOX Buttons These buttons transmit the chosen precoded CATV and satellite codes.

TV/VCR Button When the remote is in CABLE/SATELLITE mode, this is the A/B button.

LST-CH Button If your cable/satellite box has an enter function, this buttonwill send the cable/satellite box enter code.

@ EXlT/RECALUCOMMERCIAL SKIP (CS) Button

If your cable/satellite box does not have a last channel function, thisbutton willsend the TV channel recall code.

EXCLUSIVE TV Buttons

These buttons are for operating the TV.

Page 31

CABLE/SATELLITE AND VCR CODES

CABLE BRAND CODES SATELLITE BRAND CODES

ABC . .01, 03, 05, 06, 09, 11, 12, 14, 30

Antronix ....................... 44

Archer .................. 28, 40, 44

Belcor ........................ 31

Cable Star ..................... 31

Century ....................... 40

Citizen ........................ 40

Colour Voice ................ 19, 25

Comtronics ................. 29, 34

Contec ....................... 15

Dae Ryung .................... 06

Eastem ....................... 02

Electdcord ..................... 37

Everquest ..................... 13

Focus ........................ 57

Garrard ....................... 40

GC Electronics ............... 31, 44

Gemini ............... 13, 32, 36, 46

General Instrument ........... 09, 51

GoldStar ................... 29, 39

Hamlin ............ 08, 16, 27, 49, 50

Hitachi ........................ 09

Hytex ......................... 05

Jasco ........................ 40

Jerrold ...... 03, 09, 10, 12, 13, 30, 51

Macom ....................... 26

Magnavox ..................... 21

Memorex ...................... 00

Movie Time .............. 35, 37, 42

NSC ..... :... .......... 35, 37, 42

Oak .................... 05, 15, 47

Panasonic ............... 50, 17, 38

Paragon ...................... 00

Philips ............ 19, 21, 22, 23, 24,

................... 25, 40, 46, 54

Pioneer ................. 18, 39, 65

Popular Mechanics .............. 57

Pulsar ........................ 00

RCA ....................... . .17

Realistic ...................... 44

Recoton ....................... 57

Regal ................ 16, 49, 50, 53

Regency ...................... 02

Rembrandt .................. 09, 35

Runco ........................ 05

Samsung ................... 29, 39

Scientific AUanta ....... 04, 05, 14, 52

Signal ..................... 13, 29

Signature ...................... 09

SL Marx ...................... 29

Sprucer .... . ............... 17, 55

Starcom ................. 03, 13, 30

Stargate .................... 13, 29

Starquest ...................... 13

StarSight ................... 58, 59

Sylvania ...................... 01

Teleview ...................... 29

Texscan ....................... 01

Tocom .................. 10, 11, 33

Toshiba ....................... 00

Tusa ......................... 13

TV86 ......................... 35

Unika ...................... 40, 44

United Artists ................... 05

United Cable ................... 03

Universal ., ..... 28, 31,37, 40, 43, 44

Videoway ...................... 48

Viewstar .............. 21, 34, 35, 45

Zenith ..................... 05, 54

Zentek ........................ 57

GeneralInstrument.............. 61

Jerrold ..................... 61,62

Pdmestar................... 61, 62

RCA ......................... 60

Sony ......................... 63

TELEVISION BRAND CODES

Hitachi ........................ 00

Megatron ...................... 00

VCR BRAND CODES

Adventura ..................... 00

Aiko .......................... 50

Aiwa ......................... 00

Akai .................... 14, 23, 49

American High .................. 09

Asha ......................... 48

Audiovox ...................... 10

Beaumark ..................... 48

Bell & Howell ................... 30

Brandt ........................ 38

Broksonic .......... 33, 37, 43, 51, 52

Calix ......................... 10

Canon ........................ 09

Capehart...................... 05

Carver........................ 28

CCE ...................... 27, 50

Citizen ..................... 10, 50

Colt .......................... 27

Craig ................ 10, 19, 27, 48

Curtis Mathes ............ 09, 14, 22

Cybemex ...................... 48

Daewoo ........... 03, 05, 17, 29, 50

Daytron ....................... 05

Dynatech ...................... 00

Electrohome ................... 10

Electrophonic ................... 10

Emerex ....................... 06

Emerson .... 00, 01, 10, 16, 23, 33, 37,

........... 40, 41, 43, 44, 50, 51,52

Fisher ............... 19, 21, 25, 30

Fuji ....................... 07, 09

Funai ......................... 00

Garrad ........................ 00

GE .................. 09, 22, 24, 39

Goldstar ................. 04, 10, 11

Gmdiente ..................... O0

Harley Davidson ................ 00

Harman/Kardon ................. 11

Harwood ...................... 27

Headquarter ................... 18

HI-Q ......................... 19

Hitachi ............... 14, 15, 24, 31

Jansen ....................... 14

JVC .................... 02, 14, 26

KEC ...................... 10, 50

Kenwood ................ 11, 14, 26

KLH .......................... 27

Kodak ...................... 9, 10

Uoyd ......................... 00

Uoyd's ........................ 40

Logik ......................... 27

LXI .......................... 10

Magnovox ......... 09, 12, 28, 32, 34

Magnin ....................... 48

Marantz .................... 09, 28

Marta ......................... 10

Matsushita ..................... 09

VCR BRAND CODES

(Cont.)

MEI .......................... 09

Memorex .......... 00, 09, 10, 12, 18,

................... 19, 20, 30, 45

MGA ...................... 16, 23

MGN Technology ................ 45

Minolta .................... 15, 31

Mitsubishl .......... 16, 23, 26, 35, 49

Motorola ................... 09, 20

MTC ...................... 00, 45

Mulffiech ................... 00, 27

NEC .............. 11, 13, 14, 26, 30

Nikko ......................... 10

Noblex ........................ 48

Olympus ................... 09, 47

Opt_mus ................. 10, 20, 30

Odon ......................... 51

Panasonic ......... 09, 35, 46, 47, 53

Penney ...... 09, 10, 11, 13, 15, 21, 48

Pentsx .................. 15, 24, 31

Phiico ........................ 09

Phillps .................. 09, 28, 32

Pilot .......................... 10

Pioneer ....................... 26

Portland ....................... 05

Protec ........................ 27

Pulsar ........................ 12

Quarter ....................... 18

Quartz ........................ 18

Quasar ....................... 09

Radio Shack ................ 00, 10

Radix ......................... 10

Randex ....................... 10

RCA ........... 15, 22, 24, 31, 34, 39

Realistic .......... 00, 09, 10, 18, 19,

................... 20, 25, 50, 46

Ricoh ......................... 08

Runco ........................ 12

Samsung ................... 17, 45

Sanky..................... 12,2O

Sansui ..................... 14, 26

Sanyo ............... 18. 19, 30, 46

Scott .......... 16, 17, 33, 37, 43, 44

Sears ............ 09, 10, 15, 18, 19,

................... 21, 25, 30, 31

Sharp ........................ 20

Shlntom ....................... 27

Shogun ....................... 48

Singer ........................ 27

Sony ................ 05, 07, 08, 09

STS .......................... 15

Sylvania ........... 00, 09, 16, 28, 32

Symphonic .................... 00

Tatung ........................ 14

Teac ...................... 00, 14

Technics ................... 09, 35

Tekm_a ................. 00, 09, 10

Telefunken ..................... 38

TMK ...................... 40, 48

Toshiba .............. 16, 17, 25, 44

Totevision .................. 10, 48

Unitech ....................... 48

Vector ........................ 17

Vector Research ............. 11, 13

Video Concepts ........... 13, 17, 23

Videosonic ..................... 45

Wards ......... 00, 09, 15, 19, 20, 22,

................... 27, 34, 44, 48

XR-1000. ............... 00, 09, 27

Yamaha ....................... 11

Zenith .................. 07, 08, 12

Page 32

. _.. ., • • ...... .

COLOR GRAPHICGUIDE

With HITACHI'S On-Screen Display, each category has it's own color and icon. This semi-transparent system includes SET-UP, CUSTOMIZE, VIDEO, AUDIO, and INFO CENTER categories. Using the four cursor buttons, you can eas- ily access andcontrol all of the TV's functions. Checked boxes let you sothat you knowwhich function you have cho- sen. You can also choose to access the menu in English, French, or Spanish.

1. Press MENU on the remote control to display the different features on your HITACHI TV.

2. Press the CURSOR buttons to highlight and select different features.

3. Press EXIT on the remote control to quicklyexit from a menu.

CURSOR

RECALL

4. Press HELP on the remote control when a menu isdisplayed, and text will appear giving a description of that menu.

HELP

This part of the screen shows what selections are available.

This part of the screen shows which remote control buttons to use.

I 000000 I

AUTO-DEMONSTRATION

This feature will demonstrate how to use and set up your HITACHI television. To perform this feature, press the front panel POWER button and hold for five seconds. The On-Screen Display will appear on your TV set demonstrating

the settings of your TV feature.

To exit AUTO-DEMONSTRATION, press the power button on the front panel of the TV, which will tum the TV off.

Press the power button again to tum your TV set on and resume normal operation.

NOTE:

On some televisions, the SHIFT and EXCHNG that appear during the auto-demonstration are equiva-

lent to the MOVE and SWAP button respectively on your remote control.

In most cases, the MENU button is used to enter and exit the On-Screen Display.

Page 33

COLOR GRAPHIC GUIDE

SET-UP

.1[_ CUSTOMIZE

MENU LANGUAGE ]

AUTO CHANNEL SET /

cL--i-ff_g_-i !

CHANNEL ID

FAMILY FAVORITES CHILD LOCK

OPTIONS ONIOFF TIMER CLOSED CAPTION

CONTRAST

BRIGHTNESS COLOR TINT SHARPNESS COLOR TEMP.

RESET

BASS TREBLE

BALANCE

RESET ADVANCED SETTINGS VOLUME CORRECTION

SURROUND

Choose English,French,or Spanish language. Select Antenna or cable "iV.

First time set up for channel buttons. Add or delete channel.

Check channel name, scan, and child lock. Set before using timer features.

Label channels PAY1, ABC, etc.

Store family favorites channels. Block channel picture and sound.

Turn TV on oroff once, daily,or weekly. Feature to display dialogue/text.

VIDEO

Adjust contrast. Adjust brightness. Adjust color. Adjusttint. Adjust sharpness. Adjustwarm (red tones) or cool(blue tones).

SetVIDEO tofactory preset condition.

I_ INFO.

CENTER

Adjust bass.

Adjusttreble. Adjustbalance. Set AUDIO settingsto factory preset condition. Improve sound performance.

Lower volumeon selected channels.

Special soundeffects.

"_- I MESSAGES

I Used to leave message or daily reminder.

Page 34

Select SET-UP when setting your TV up for the first time. buttons on the remote to highlightthe function desired.

SET-UP

Use the CURSOR A,V

I MENU LANGUAGE I This feature will allow you to select any one of three different languages for all On-Screen

I Displays.

CURSOR

SET-UP

CURSOR

Use CURSOR • or • to select the MENU LANGUAGE of yourchoice.

Press EXIT to quit menu or CURSOR < to retum to previousmenu.

Page 35

SET-UP

SIGNALSOURCE

I Select ANTENNA ifyou are using an indoor or outdoor antenna. Select CATV if you have

cable TV.

lCURSOR

SET-UP

CURSOR

Press CURSOR • or • to highlight and select the correct SIGNAL SOURCE mode. Press EXIT to quit MENU or CURSOR < to retum to previous menu.

ANTENNA

VHF2 ~ 13ch

UHF 14 ~ 69ch

RECB_3ON BAND

CATV 1 OR CATV 2

CATV CHANNEL Indicated on

VHF2 - 13

Mid band A ~ I

A-5 - A-1

Super band J - W

Hyper band

W+I -W+28

Ultra band

W+29-W+84

the screen

2-13

14 - 22 95 - 99 23 - 36 37 - 64

65 - 125

Reception channels for each mode are shown at the left.

Refer to your cable or TV guide for channel identifi-

cation standards.

If certain CATV channels are poor or not possible in CA'I'V1 mode, set SIGNAL SOURCE to CATV2.

Page 36

SET-UP

I AUTO CHANNEL SET I This feature will automatically store active TV channels in CHANNEL ADD/DEL. This will

allow you to skipover unused channels when using the CHANNEL UP (A) or DOWN (V) buttons.

CURSOR

If the EXIT button is pressed while the AUTO CHANNEL SET function isengaged, programming will stop. Remember to select the correct SIGNAL SOURCE mode before using AUTO CHANNEL SET.

See CHANNEL ADD/DEL to add or erase additional channels.

Page 37

SET-UP

I CHANNEL ADD/DEL I Use this function after AUTO CHANNEL SET to add or erase additional channels to the

I remote control CHANNEL • or • buttons.

SET-UP

CURSOR

Add or erase additional channels while still in CHANNEL ADD/DEL using CURSOR • or•, CHANNEL • or •, and number buttons and then add or erase using the CURSOR • button.

Press EXIT to quit menu or CURSOR • to retum to previous menu.

Page 38

I CHANNELLIST

SET-UP

I This function allows youto view whichchannels are labeled in CHANNEL ID (NAME), which

have been added to CHANNEL ADD/DEL (SCAN), and which are protected by CHILD

LOCK (LOCK).

CURSOR

Press CURSOR • or • to view morechannels. Press EXIT to quit menu or CURSOR • to retum to previous menu.

CLOCK SET

I Use this feature for all time related functions. The time mustbe set before you can use the

ON/OFF TIMER or MESSAGE.

SET-UP

CURSOR

Use CURSOR • or • buttons to set the time and AM or PM.

Press CURSOR I_ to change position. Press EXIT to quit menu or CURSOR • to retum to previous menu.

Page 39

CUSTOMIZE

This selection contains advanced features which will make TV viewing easier and more enjoyable.

CHANNELID

I Use this feature to name up to 25 channels.

CUSTOMIZE

CURSOR

Press CURSOR • or • to select letters. Press CURSOR I_ to change character position.

Press CHANNEL • or • to select and label additional channels. Press EXIT to quit menu or CURSOR • to return to previous menu.

The CHANNEL ID will appear in the top right comer of the screen when the RECALL button is pressed.

The (*) represents a blank space. Select ERASE ID to erase a CHANNEL ID. An "ARE YOU SURE?" displaywill appear on the screen to confirm your

choice.

I NOTE: CHANNEL ID will be displayed only when channel is displayed as main picture. I

Page 40

I FAMILY

FAVORITES

CUSTOMIZE

I With Family Favorites, you can easily access your favorite movie, sports, news, and custom

stations by registering any of your favorite stations into one of four categories. Once you

have input your four favorite stations in each category, you simply press any of the cursor buttons and the Family Favorite'sscreen appears. Nowyou can easily switch between your

16 favorite stations.

CURSOR

Use CURSOR • or • buttons to highlightthe category you wish to registerthe channel under. Press CURSOR • to select the column you wish to register the channel under.

Press CHANNEL • or • or the number buttons to enter the desired channel. The channel to be added is displayed

in the top dghtcomer of the screen.

Press MENU button to register your favorite channel. Repeat untilthe category has been registered with your favorite channels.

To erase a FAMILY FAVORITES channel, enter O0 as channel then press MENU button.

Once your favodte channels are registered inthe FAMILY FAVORITES menu, your TV set will change to that station

when selected.

Press EXIT to remove FAMILY FAVORITES OSD from the SCREEN.

I NOTE:

After all of your favodte channels are registered, the CURSOR buttons can be used for quick access to the FAVORITE CHANNELS menu.

Page 41

CUSTOMIZE

I CHILD LOCK

OPTIONS

JThis feature allows you to block out the picture and sound of the selected channel or video

input of any channel that you feel may be inappropriate for your children. There is no limit

to the number of channels that can be locked. Your secret code allows you to reinstate

these channels any time you wish. it can also be used to schedule an amount of time that the TV cannot be viewed.

CUSTOMIZE

CURSOR

The code to enter CHILD LOCK is a three digit key number. The factory preset code is 000.

Use CURSOR • or • to select number or CURSOR • to change position.

LCURSOR

CURSOR

Q Q

Use CURSOR • or • to highlightfunction and CURSOR • to set ON or OFF.

When CHANNEL is tumed on, the picture and sound forthe chosen channel will be blocked out. When VIDEO is turned on, the picture and sound for the video input will be blocked out. When QUICK LOCK is turned on, the picture and sound for channels 3, 4 and all video input will be blocked ouL

When "IV TIME OUT is turned on, you can set the BEGIN and END times and the "IV cannot be viewed during that time pedod.

To change the key number, select CHANGE CODE. Enter a new three digit key number you prefer.

Ifyou forget your key number, use the factory code 777 to erase your key number. This will reset the key number back Io the factbry preset 000.

Page 42

ON/OFF TIMER

CUSTOMIZE

This function will automatically tum the TV set on or offone time only, every day, or once a week. Itcan also be set to turnon to your favorite program, or as a reminder, to tum to your favorite program when the TV is already on.

cus'rom_

CURSOR

PressCURSOR • or • to selecteithertheON orOFF TIMER. PressCURSOR • to highlightselectiontobe changed.

PressCURSOR • or • toselect thetimetheTV will tumonandoff andto chooseAMor PM. PressCURSOR • to exit time setting.

SelectCHANNELand pressCHANNEL• or• toset the channeltheTV willtuneto when itautomaticallyturnson. PressCURSOR • to exitchannelsetting.

Press CURSOR • or • to highlightthen CURSOR • to select mode: ONCE (one time only), DALLY(every day), or WEEKLY (once a week). Press EXIT to quit menu or CURSOR • to retum to previous menu.

NOTE:

Youcan seteitheron timeonlyor offtime only,orboth. The modewill bethe sameforboth.

IftheTV isturnedonbytheONTIMERandthereisnoremotecontroloperationinthreehoursormore, theTV willautomaticallyrumoff.

I ,_CAUTION: Do not use your TV as a deterrent when away from home by usingboth the ON TIMER and I

OFF TIMERS. For safety, the TV should be tumed off when you are away from home.

Page 43

CUSTOMIZE

I CLOSED

CAPTION

Closed captions are the dialogue, narration, and/or sound effects of a television program

or home video which are displayed on the TV screen allowing you to read the dialog

being spoken (when broadcast). Your local TV program guide denotes these programs as _ or I_.

CUSTOMIZE

CURSOR

DISPLAY: ON/OFF will tum the _ display on or off.

MODE: C.C. (Closed Caption) is for the program you are viewing.

MODE: TEXT is for additional information such as news reports or a TV program guide. This information

covers the entire screen and viewing the TV program is not possible. TEXT may not be available

with every _ program.

CHANNEL: 1 is used for the primary language (usually English). CHANNEL: 2 issometimes used for a second language (may vary by region).

Use CURSOR • or • to highlight the function to be changed; press CURSOR • to change the function. Press EXIT to quit menu or CURSOR < to retum to previous menu.

weatherToday

Sunny 70

WeatherToeggwow

A bit cooler 3

WlndChill -55"

C.C. Selected

Text Selected

JNOTE:

The word MUTE will not be displayed if the Closed Caption Display is ON. Ifyou do not have sound, I make sure MUTE is not set.

Page 44

Select VIDEO to adjust picture settings and improve picture quality.

VIDEO

CURSOR

Use the CURSOR • or • to highlight the function to be adjusted.

Press CURSOR ,d or • to adjust the function. Press EXIT to quit menu or CURSOR < to retum to previous menu.

CONTRAST Use this function to change the contrast between black and white levels inthe picture.

BRIGHTNESS Usethisfunctionto adjustoverallpicturebrightness.

COLOR Use this function to adjust the level of color in the picture.

TINT

Usethisfunctiontoadjustfleshtonessotheyappearnatural.

SHARPNESS

Use this function to adjust the amount of fine detail in the picture.

COLOR TEMP.

Use this function to adjust the white balance (hue) ofthe picture to your own color preference.

When shipped from the factory, this is set to COOL If you prefer a reddish screen, set to WARM.

RESET

When RESET is selected, the "ARE YOU SURE?" display will appear on the screen to confirm your choice. Press

CURSOR • to return VIDEO adjustments to factory preset conditions.

NOTE:

If CONTRAST is selected you are adjusting CONTRAST, the additional menu items COLOR, TINT, BRIGHTNESS, SHARPNESS, and RESET can be viewed on the screen and can also be adjusted by

scrolling through them using the CURSOR • or V. This isalso true for all of the menu items inVIDEO.

Page 45

AUDIO

Select AUDIO to adjust the TV to your preference and to improve the sound quality.

CURSOR

Use the CURSOR • or • to highlightthe functionto be adjusted. Press CURSOR ,d or • to adjust thefunction. Press EXIT to quit menu or CURSOR ,d to retum to previous menu.

BASS Thisfunctioncontrolsthe lowfrequencyaudiotoallspeakers.

TREBLE This function controls the high frequency audio to all speakers.

BALANCE This functionwill control the leftto right balance of the TV internal speakers and the AUDIO TO HI FI output.

RESET

When RESET is selected, the "ARE YOU SURE?" displaywill appear on the screen to confirmyour choice. Press CURSOR • to retum AUDIO adjustments to factory preset conditions.

NOTE:

If BASS is selected you are adjusting BASS, the additional menu items TREBLE, BALANCE, and RESET can be viewed on the screen and can also be adjusted by scrolling through them using the

CURSOR • or •. This is also truefor all ofthe menu items in AUDIO.

Page 46

I ADVANCED

SETTINGS

AUDIO

I se ADVANCED SETTINGS to improve the sound performance ofyour TV depending on

listening conditions.

CURSOR

Press CURSOR • or • to highlight a function.

Press CURSOR • to change the function setting. Press EXIT to quit menu or CURSOR • to returnto previous menu.

MTS MODE Multi-ChannelTelevisionSound(MTS) will allowyou to selectSTEREO (Stereo Broadcast),SAP (SecondAudio Program)whichmay be a secondarylanguage,weatherreport,etc.or MONO (MonauralSound)usedwhenreceiv- inga weakstereobroadcast. The sourcesreceivedwillbe displayedbelowthechannelnumber.The MTS modeyouselectedwillbedisplayedto the left of the channel number. See examplebelowfor each selectionwhen bothstereo andsecondaudioare received(monauralis alwaysreceived).

STEREO SELECTED

STEREO 31

NEWS STISA

SAP SELECTED

SAP 31

NEWS ST/SA

MONO SELECTED

NOISE CANCELER This function eliminates the noise in between stations. If a channel is tuned and is noisy, this function will automati-

cally eliminate the audio and video for that channel.

LOUDNESS This function will improve the quality of both low and highfrequency sounds when listening at low volume levels.

INT. SPEAKERS

This fur]ction is useful when first setting up the extemal speakers, or if you prefer to use only speakers from a sepa-

rate stereo system.

Page 47

AUDIO

I VOLUME I

CORRECTION

Use this function to reduce the volume level of up to four channels that sound loud com- pared to other channels.

CURSOR

Press CURSOR • or • to highlight one of the fourvolume corrections, then CURSOR b, to select. Press CHANNEL • or • and number buttons to select a channel.

Press MENU to set the channel to be volume corrected. Press CURSOR • or • to adjust volume level in 5% increments. Press EXIT to quit menu or CURSOR ,< to retum to previous menu.

NOTE:

1. Volume Correction adjustment is for the channel display in the top right comer of the screen. To

adjust a different channel, you must select the channel with the channel or number buttons and press CURSOR I_.

2. Ifthe channel has been corrected before, use the CURSOR • or • to highlightand CURSOR I_ to select that channel, then use the CURSOR • or • to change the level.

3. To erase a channel from volume correction, select channel O0 and press MENU.

4. The volume level will change from 50=/oto 100% in increments of 5%.

Page 48

I SURROUND

AUDIO

J The following surround sound settings will reproduce the *live" sound you would hear in

concert halls, movie theaters, etc. when you set up your speaker system as shown in the

section on rear panel connections on pages 15, 16 and 19. The surround system is most effective with movies played on a stereo VCR.

Surround sound allows the viewer to enjoy sound which provides a feeling of =presence"

from stereo broadcasts and VCR tapes recorded with stereo sound. Also a mono input,

simulating a stereo, will increase the sound givingthe listener simulated surround sound.

CURSOR

SURROUND OFF Usethisfor normalstereo/monobroadcasts.

NOTE:

If sound is noisy when a stereo broadcast is received, and the TV is set to the SURRC)UND mode, decrease the TREBLE control or tum the Surround OFF.

MOVIE SURROUND Listener issurrounded by many sound sources such as a movie theater reproduction.

I NOTE: Some TV systems do not transmit optimum audiochannel separation which can reduce the effective- I

ness of the MOVIE SURROUND function.

MUSIC SURROUND

With resonant sound, listener has the feeling of being in a concert hall. At stereo input,the sound of music increases.

SIMULATE SURROUND At mono input, sound is increased, simulating a stereo like Surround.

Your VCR must be a Hi-Fi or stereo unit. See page 18 for stereo VCR connection. Set must be outputting stereo. (See MTS Mode: STEREO on page 46.)

Page 49

INFO CENTER

INFO.

CENTER

I This function allows the user to program messages in the TV.

MESSAGE 1

I Use this functionto program one or two personal messages in yourTV's memory up to a

maximum of 31 characters. The user can program the message to appear one time only or every day.

Press CURSOR • to select MESSAGE 1 or MESSAGE 2. Press CURSOR • or • to highlight your selections.

Press CURSOR • to select your choice. Press CURSOR • or • to select letters or other characters.

The asterisk (*) represents a blank space. To erase the message, use CURSOR • or • until ERASE MESSAGE is highlighted, then press CURSOR • to erase

message.

The "ARE YOU SURE?" display will appear on the screen to confirmyour choice.

J CURSOR

CURSOR

Press CURSOR • or • to choose MODE or TIME. Press CURSOR • to set MODE when it is highlighted.

Press CURSOR • or • to set the time. Press EXIT to quit menu or CURSOR < to return to previous menu.

I NOTE:

At the selected time, the message will be displayed untila remote control button is pressed.

Message 2 works the same way as Message 1.

Page 50

USEFUL INFO

Make sure the "iV is tumed off when cleaning the screen.

Dust the screen and cabinet with a soft cloth.

Clean the screen with a soft cloth moistened in warm water. Dry with a softcloth. A mild soap may he used if the screen is extremely dirty.

Place your TV and remote control away from extreme heat, humidityand extremely dusty places.

Remove the plug from the wall outlet if your television will not he used for a long pedod of time, for instance, when you go on vacation.

DO NOT

Do not clean your screen or cabinet with strongcleaners, polishes, or chemically treated cloth.

Do not place rubber or vinyl products or cellophane tape on your set.

Do not touch the screen too often.

Donotsubjecttheremotecontroltoshockssuchasdroppingitonthefloor,etc. Physicaldamageto the precision partsmay result.

Avoid placing the remote control in a high humidity place or getting it wet. Do not leave it on or near a heater. Excessive heat or moisture may cause the unit to cease operation.

When the battedes run down, remote control operationwill become erratic or possibly stop altogether. Replace the old batteries with two new "AA"size batteries.

Page 51

USEFULINFO

• IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift.

Usually caused by interference from automobile ignition systems, neon lamps, electrical drills, and other electrical appliances.

• GHOSTS: Ghosts are caused by the television signal followingtwo paths. One is the direct path and the other is reflected from tall buildings,hills or some other objects. Changing the direction or position of the antenna may improve

reception. Ghosting may also be caused by defects in the antenna system

such as unshielded leads or connecting several sets to the same antenna without usingmultiple antenna couplers.

• SNOW:

If your receiver is located in the fdnge area of a television station where

the signal isweak, your picturemay be marred by the appearance ofsmall dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture.

• RADIOFREQUENCYINTERFERENCE: The interferenceproducesmoving ripplesor diagonalstreaks, and in

somecases,causes lossofcontrastinthe picture.

Page 52

USEFUL INFO

SYMPTOMS

No Picture, no sound • • • • • • •

Sound OK, picture poor • • • • • • • •

Picture OK, sound poor • • • • • • •

Picture blurred • • • • • •

Lines or streaks in picture • • • • •

Poor reception on some channels • • • • •

No color • • • • • •

Poor color • • • • • • •

ThisColorTelevisionincorporatesadvancedpowersurgeprotectiontechnologydesignedtoprotectagainstcom-

ponentorcircuitdamagedueto intemalvoltageor powersurges.

IF YOUR SET SHOULD APPEAR TO HAVE A LOSS OF POWER, PLEASE FOLLOW THIS PROCEDURE:

1) Press the power switch (ON/OFF switch) once.

2) If there is still no power, wad 30 seconds and pressthe power switch again.

3) if there is still no power, unplug the power cord from the wall. Wait thirty seconds and plug the power

cord back in. Press the power switch again.

This protective technology should provide for years of lasting entertainment from your HITACHI Color Television.

Page 53

USEFUL INFO

Features:

Superfine picture Quality 700 Line Horizontal Resolution

Dark "13ntCPT with Self Dynamic Focus Gun Remote Transmitter

(Controls many VCR, Cable Box, and Satellite Brands) Picture-in-Picture Functions

ICONS: Color Graphic Guide Full set of Input Jacks, including S-Video Closed Caption Decoder Comb Filter, Wide-Band Video-Amp and Temperature Control MTS (Multi-Channel Television Sound) Stereo Broadcast Reception

3D Surround Sound (3 Way)

Screen Size: 32V (32 inches measured diagonally)

Inputs:

Power Input .................. AC 120V, 60Hz

Power Consumption (operating) .......... 135W

Power Consumption (Maximum) .......... 180W

Antenna input impedance ............. 75 Ohm

Channel coverage ................. .. 181 ch.

VHF-Band .......................... 2- 13

UHF-Band ......................... 14 ~ 69

CATV Mid Band ................... A-5 - A-1

................................. A*I

Super Band ........................... J-W

Hyper Band .................... W+I - W+28

Ultra Band .................... W+29 - W+84

Video ..................... 1.0Vp-p, 75 Ohm

S-Video

Luminance (Y) ............... 1.0Vp-p, 75 Ohm

Chrominance (C) ............. 1.0Vp-p, 75 Ohm

Audio input level ................... 47k Ohm

Average input level ................ 470mVrms

Maximum input level ............... 940mVrms

Dimensions:

• Height (in.) 2611/lS

• Width(in.) 311hs

• Depth (in.) 22=/_

• Weight (Ibs.) 132

I NOTE: Due to improvements, specifications in this operating guide are subject to change without notice. I

Page 54

USEFULINFO

HITACHI

To locate an authorized

HITACHI sewice facility in the continental U.S.A.

and Canada,

DIAL TOLL FREE

7 days a week, 24 hours a day

(1-800-448-2244 )

Hitachi Home Electronics (America), Inc.

Hitachi has made every effort to assure you hours of troublefree operation from your unit. However, should you require service, a network of Hitachi Authorized Service Facilities has been established in all 50 states and Puerto

Rico. Each facility will provide you with convenient and expedient assistance. Our service hotline operator will

direct you to the Hitachi Authorized Service Facility nearest you. Just present proofof purchase and/or delivery

receipts to the Hitachi Authorized Service Facility,and service will be rendered in accordance with the terms of the

limited warranty as stated on your warranty card or operating guide.

Should you have any questions regarding warranty, service, operation or technical assistance,

please contact:

Hitachi Home Electronics (America), Inc. 3890 Steve Reynolds Blvd.

Norcross, GA 30093

Tel: 770-279-5600

Hitachi Sales Corporation of Hawaii 3219 Koapaka St. Honolulu, HI 96819 Tel: 808-839-3621

For TVs t_urchased in Canada only. please contact one of the Hitachi offices below, should you have any questions regarding service, operation, or technical assistance.

MONTREAL

9425 Trans Canada

Saint-Laurent, Quebec

H4S 1V3

TORONTO

6740 Campobello Road

Mississauga, Ontario

L5N 2L8

VANCOUVER

20800 Westminster Hwy., Unit 1103

Richmond, B.C.

V6V 2W3

Tel: (514) 956-9882

Pax: (514) 956-9761

Tel: (905) 821-4545

Fax: (905) 826-6627

Tel: (604) 214-0777

Fx: (604) 214-0772

Page 55

NOTES

Page 56

HITACHI

QR25351