Hitachi 32-42PD7800 Service Manual

YK

No.013E

32PD7800

SERVICE MANUAL

42PD7800

(PW2)

Caution

Be sure to read this manual before servicing. To assure safety from fire, electric shock, injury, harmful radiation and materials, various measures are provided in this HITACHI Plasma display.

Be sure to read cautionary items described in the manual to maintain safety before servicing.

Service Warning

1.Since Panel Module and front Filter are made of glass, handling the broken Module and Filter shall be taken care suffi ciently in order not to be injured.

2.Replacing work shall be started after the Panel Module and the AC/DC Power supply become sufficiently cool.

3.Special care shall be taken to the display area in order not to damage its surface.

4.The Panel Module shall not be touched with bare hand to protect its surface from stains.

5.It is recommended to use clean soft gloves during the replacing work in order to protect not only the display area of the Panel Module but also a serviceman himself.

6.The Chip Tube of Panel Module (located upper left of the back and surrounded by frame) and fl exible cables connecting Panel glasses to drive circuit PWBs are very weak, so shall be taken care suffi ciently not to break. If you break Chip Tube, the Panel doesn’t display anything forever.

Contents

1.	Features --------------------------------------------------	3	9. Basic circuit diagram---------------------------------	43
2.	Specifi cations--------------------------------------------	4	10.Printed wiring board diagram----------------------	55
3.	Service point---------------------------------------------	5	11.Block diagram -----------------------------------------	61
4.	Component names-------------------------------------	6	12.Connection diagram ---------------------------------	62
5.	New adoption technology-----------------------------	7	13.Wiring diagram ----------------------------------------	63
6.	Adjustment ---------------------------------------------	11	14.Disassembly diagram--------------------------------	67
7.	Troubleshooting---------------------------------------	31	15.Replacement parts list-------------------------------	73
8.	Self-diagnosis function ------------------------------	41

SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT.

Plasma Display

September 2004 Digital Media Division

32PD7800/42PD7800 (PW2)

CAUTION FOR SAFETY

Please read this page before repair the monitor.

This page explains to following items for keep the safety of set and prevent to accident during repair work.

We explain by symbol at happen the damage or injury when took wrong repair.

Warning	This symbol means "possible to die or heavy damage"
Caution	This symbol means "possible to damage or something will break"

We made the symbol as below, which are kind of following items.

This symbol means "CAUTION"

This symbol means "POSSIBLE to

ELECTRIC SHOCK"

This symbol means "MUST"

This symbol means "DO NOT"

WARNING

Should be follows to instructions.

We indicates to cabinet, chassis and parts by label, which are special attention part. Please follow to note and [Safety Instructions] of User’s Manual.

Prevent the electric shock.

Please take care during working because monitor has high voltage part and power supply part.

Possible to die if you tough to these place by miss take.

Please disconnect power plug during overhaul, reassemble or change parts.

You will die or take damage by electric shock if you touch to live part.

Use recommended components.

Please use to same characteristic component, which is same as previous for your safety and keep reliability especially marked byin parts list and circuit diagram.

It is reason of electric shock or fire if you use non-recommended component.

Should be kept same style of wiring or component.

Monitor uses tubes or tapes, which made by insulator, and some components are keep distance from surface of PWB for safety.

Internal leads kept from hot part or high voltage part by clamper or styling, so please return to original condition for prevent to electric shock or fire.

Should be done safety check after finished.

Every part (removed screws, component and wiring) should be returned to previous condition.

Check around repair position for make damage by miss take and measure the insulated impedance by meg-ohm meter. Confirm the value of impedance, that value is more than 4M ohm.

It is reason for electric shock or fire if that value is less than 4M ohm.

Nobody can check and repair to the code and combination circuit of HDCP.

Never remove the shield case, which is

assembled to the code and combination

circuit of HDCP.

2

32PD7800/42PD7800 (PW2)

PRECAUTIONS

How to clean the plasma screen panel of the monitor

Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet.

To prevent scratching or damaging the plasma screen face, do not knock or rub the surface with sharp or hard objects. Clean the screen with a soft cloth moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not use harsh or abrasive cleaners.

How to clean the cabinet of the monitor

Use a soft cloth to clean the cabinet and control panel of the monitor. When excessively soiled dilute a neutral detergent in water, wet and wring out the soft cloth and afterward wipe with a dry soft cloth.

Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. especially because they would cause discoloration, scratches or cracks.

1. Features

Large-screen, high-definition plasma display panel

The 42-inch color plasma display panel, with a resolution of 1024 (H) x 1024 (V) pixels, and the 32-inch color plasma display panel with a resolution of 852(H) x 1024(V) pixels, creates a high-definition, large-screen(aspect ratio : 16:9) and low-profile flat display. Free from electromagnetic interferences from geomagnetic sources and ambient power lines, the panel produces high-quality display images free from color misconvergence and display distortion.

High Performance Digital Processor

A wide range of input signals can be handed,including composite, component,and HDMI.High Definition Digital Processor creates the fine-textured image with dynamic contrast. In addition, it corresponds to a broad array of personal computer signals, from 640 x 400 and 640 x 480 VGA to 1600 x 1200 UXGA.(Analog Input)

Easy-to-use remote control and on screen display system

The remote control included eases the work of setting display controls. Further, the on-screen display system, displays the status of signal reception and display control settings in an easy-to-view fashion.

Power saving system

The International ENERGY STARpower saver feature saves power consumption automatically when input signals are not available.

When connected to a VESA DPMS-compliant PC, the monitor cuts its power consumption while it is idle.

Connecting to an Audio Visual Device

•Two composite/S terminal*1,three composite terminal*2, two component terminal*2, a HDMI terminal and a photo input terminal(42 only) have been added. A composite video output terminal is also provided as a monitoring output.

*1

*2

A composite/S terminal = A side input

Two composite terminal and two component terminal are used at the same time. The component terminal would govern.

•A wide range of devices other than personal computers can also be connected.

•A RGB input is possible to switch to component signal from the Menu screen.

Power Swivel Feature

It allows to turn the plasma display left or right within ± 30 degree using the remote control.

3

32PD7800/42PD7800 (PW2)

2. Specifications

	Display	Approx. 32 inches (716 (H) x 399 (V) mm,		Approx. 42 inches (922 (H) x 522 (V) mm,
Panel	dimensions	diagonal 820mm)		diagonal 1059mm)
	Resolution	852 (H) x 1024 (V) pixels		1024(H) x 1024 (V) pixels
Net dimensions		850 (W) x 545 (H) x 110 (D) mm		1050 (W) x 676 (H) x 110 (D) mm
(excluding Speakers/Stand)
Net weight		25.5kg		37.0kg
(excluding Speakers/Stand)
Ambient	Temperature	Operating : 5˚C to 35˚C, Storage : 0˚C to 40˚C
conditions	Relative humidity	Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)
Power supply		AC100 - 240V, 50/60Hz
Power consumption/at standby		245W / <3W		380W / <3W
Audio output		speaker 12W + 12W (6Ω)		speaker 12W + 12W (6Ω)
(RGB input)
		RGB1 DVI input terminal (DVI-D)
Input terminals		RGB1 audio input terminal (3.5mm Stereo Mini Jack)
		RGB2 analog RGB input terminal (D-sub 15-pin)
		RGB2 audio input terminal (3.5mm Stereo Mini Jack)
Input signals		0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)
		480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
		H/V separate, TTL level [2KΩ]
Sync signals		H/V composite, TTL level [2KΩ]
		Sync on green, 0.3 Vp-p [75Ω]
Recommended signal		44 modes
(Video input)
		AV1: composite video input terminal (RCA)
		AV1: Y/ PB/ PR video input terminal (RCA)
		AV1: L/R audio input terminal (RCA)
		AV2: composite video input terminal (RCA)
		AV2: Y/ PB / PR video input terminal (RCA)
Input terminals		AV2: L/R audio input terminal (RCA)
		AV3: composite video input terminal (RCA)
		AV3: S video input terminal
		AV3: L/R audio input terminal (RCA)
		AV4: composite video / L/R audio input terminal (RCA)
		AV5=AV3
		AV6=HDMI input terminal
		Photo input terminal (42 Model)
		AV1: PAL, SECAM, NTSC3.58, NTSC4.43
		AV1: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
		AV2: PAL, SECAM, NTSC4.43, NTSC3.58
Input signals		AV2: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60
		AV3: PAL, SECAM, NTSC4.43, NTSC3.58,
		AV4: PAL, SECAM, NTSC4.43, NTSC3.58,
		AV5=AV3
		AV6=HDMI input signal
		OUTPUT (MONITOR): composite video monitor-output terminal (RCA)
Output Signal		OUTPUT (MONITOR): L/R audio monitoroutput terminal (RCA)
		OUTPUT (HEADPHONE): L/R audio monitoroutput terminal (3.5mm Stereo Mini Jack)
Recommended signal		23 modes
(RF input)
Input terminals		ANT : 75Ω Unbalanced
		PAL B, G, H / I / D, K
RF Video System		SECAM B, G / D, K / K1
		NTSC-M

Applicable video signals for each input terminal

Terminal		RCA			HDMI		DVI		D-sub
Signal	CVBS	S-video	Component	RGB		PC		STB	RGB	Component
AV1
AV2
AV3
AV4
AV5
AV6
RGB1
RGB2
										( :Available)

4

32PD7800/42PD7800 (PW2)

3. Service points

Lead free solder

This product uses lead free solder (unleaded) to help preserve the environment. Please read these instructions before attempting any soldering work.

Caution: Always wear safety glasses to prevent fumes or molten solder from getting into the eyes. Lead free

solder can splatter at high temperatures (600˚C).

Lead free solder indicator

Printed circuit boards using lead free solder are engraved with an "F."

Properties of lead free solder

The melting point of lead free solder is 40-50˚C higher than leaded solder.

Servicing solder

Solder with an alloy composition of Sn-3.0Ag-0.5Cu or Sn-0.7Cu is recommended.

Although servicing with leaded solder is possible, there are a few precautions that have to be taken. (Not taking these precautions may cause the solder to not harden properly, and lead to consequent malfunctions.)

Precautions when using leaded solder

Remove all lead free solder from soldered joints when replacing components.

If leaded solder should be added to existing lead free joints, mix in the leaded solder thoroughly after the lead

free solder has been completely melted (do not apply the soldering iron without solder).

Servicing soldering iron

A soldering iron with a temperature setting capability (temperature control function) is recommended.

The melting point of lead free solder is higher than leaded solder. Use a soldering iron that maintains a high stable temperature (large heat capacity), and that allows temperature adjustment according to the part being serviced, to avoid poor servicing performance.

Recommended soldering iron:

Soldering iron with temperature control function (temperature range: 320-450˚C)

Recommended temperature range per part:

Part	Soldering iron temperature
Mounting (chips) on mounted PCB	320˚C±30˚C
Mounting (chips) on empty PCB	380˚C±30˚C
Chassis, metallic shield, etc.	420˚C±30˚C

The PWB assembly which has used lead free solder

FILTER PWB, SW PWB, LED/RECEIVER PWB, SP TERMINAL(L/R) PWB

AUDIO PWB, JOINT PWB, Swievel PWB, HDHI PWB, control PWB

VIDEO PWB TUNER PWB

Readjustment Power supply voltage

When a PANEL or a Power Unit is exchanged, power supply voltage needs to be adjusted. Please adjust to make the values of Va and Vs of as should on the label currently stuck on the panel back upper parts.Adjustment is performed by VR in the power supply unit. Please refer to the procedures of “Va” and “Vs” adjustments on 23page.

5

32PD7800/42PD7800 (PW2)

4. Component names

[Main unit]

Control panel

• Adjustment buttons are located on the bottom.

• The back cover is provided with indications to distinguish the adjustment buttons.

MENU button

	-			+		INPUT SELECT button
	VOLUME					(OK button)
	UP/DOWN					SELECT button
	buttons
	(		ADJUST			SELECT button
	buttons)
	SUB-POWER button

Remote-control receiver

Indicating lamp

•The main power switch is located at the back, on the lower surface.

Main power switch

(32")

(42")

• ( ) indicates the function while the MENU is displayed on the screen.

[Remote control]

POWER button

INPUT SELECT buttons

MENU button

OK button

SOUND MODE button

VOLUME UP/DOWN button

PROGRAM SELECT buttons (TV)

MULTI MODE button

T/TEXT button (TV)

RECALL button

FUNCTION SELECT button

DVD CONTROL buttons

FREEZE/RETURN button

SELECT/ADJUST button

PICTURE MODE button

CH I/CH II button (TV)

CHANNEL UP/DOWN button (TV) MUTE button

MULTI PICTURE button

PHOTO INPUT buttons

SWIVEL button

CLE-960

6

32PD7800/42PD7800 (PW2)

5. New adoption technology

[System control micom I001(M3062)]

Pin function table

No.	PIN MANE	I/O	FUNCTION
1	VREF (+5.0V)	I	5V
2	+5.0V	I	5V
3	NC	I/O	NC
4	OSD_DATA	I/O	OSD DATA
5	OSD_CLK	I/O	OSD CLK
6	HP_VOL	I/O	Head Phone Volume
7	FE.AGC_O(M)	I/O	AGC Voltage(F/E)
8	DATA_OUT(FC)	I/O	FC DATA
9	DATA_IN(FC)	I/O	FC DATA
10	CLK(FC)	I/O	FC CLOCK
11	EDID_PROTECT	I/O	Memory Protect
12	TRAP_MAIN	I/O	TRAP-MAIN
13	GND	I	GND
14	CNVSS(FLASH)	I	CNVSS(FLASH)
15	DSUB COMP	I/O	SYNC-SW
16	RGBSW	I/O	SYNC-SW
17	RESET	I	RESET
18	16MHz oscillation	O	OSC-OUT
19	GND	I	GND
20	16MHz oscillation	I	OSC-IN
21	+5.0V	I	5V
22	NMI(+5.0V)	I	5V PULL UP
23	RMCON(AVC)	I/O	IR Signal
24	V.FREQ_2(VIDEO)	I/O	TA1370(LA7213), COMPONENT2
25	V.FREQ_1/3	I/O	TA1370(LA7213), COMPONENT(Main)/ DSUB COMPONENT
26	SCV.SYNC	I/O	CVBS for SYNC Detection(Sub Picture)
27	IRQ PM-IRQ)	I/O	PANEL MODULE Condition(L:Normal,H:Erroe)
28	MCV.SYNC	I/O	CVBS for SYNC Detection(Main Picture)
29	POWER_LED	I/O	L LED ON(Power Save)
30	H.FREQ_2(VIDEO)	I/O	TA1370(LA7213), COMPONENT2
31	PDP_WVGA_LCD_SW_2	I/O	PDP/42WVGA/LCD detection
32	H.FREQ_1/_3	I/O	TA1370(LA7213), COMPONENT1(Main), D-SUB
33	PDWN	I/O	RESERVE(LVDS Power Down mode(PANEL))
34	RXD2	I/O	DTT
35	TXD2	I/O	DTT
36	TXD1(RS232C/FLASH)	I/O	DATA(RS-232C)
37		I	5V
38	RXD1(RS232C/FLASH)	I/O	DATA(RS-232C)
39		I	GND
40	SCLK(FLASH)	I/O	CLOCK(FRASH MEMORY Writing)
41	BUSY(FLASH)	I/O	BUSY(FRASH MEMORY Writing)
42	TXD0(PDP)	I/O	Ether Net
43	RXD0(PDP)	I/O	Ether Net
44	SDA4(panel)	I/O	I2C-BUS Contorol DATA
45	SCL4(panel)	I/O	I2C-BUS Contorol CLOCK
46	M_ENABLE	I/O	Media Enable
47	M_SCLK	I/O	Media Clock
48	M_SDA	I/O	Media Data
49	M_WAKEUP	I/O	Media Wakeup
50	PDPGO(PM_ON)	I/O	PDP PALEL Contorol

7

			32PD7800/42PD7800 (PW2)
No.	PIN MANE	I/O	FUNCTION
51	CPUGO(PM_CPU)	I/O	PDP PALEL Contorol
52	EPM (FLASH)	I/O	FRASH MEMORY Writing
53	VIDEO.DET_1	I/O	Detecting VIDEO PWB
54	SCL1	I/O	I2C to PWB TUNER side FE/MSP3455or MSP3415G/SAA5361/TB1274(Sub)/M306V7/M62320P
55	SDA1	I/O	I2C to PWB TUNER side FE/MSP3455or MSP3415G/SAA5361/TB1274(Sub)/M306V7/M62320P
56	HDMI-RESET	I/O	HDMI-Reset
57	HDMI-HPD_RESET	I/O	Hot Plug Detect Reset
58	VIDEO.DET_2	I/O	Detecting VIDEO PWB
59	VIDEO.DET_3	I/O	Detecting VIDEO PWB
60	TUNER.DET_1	I/O	Detecting TUNER PWB
61	CE (FLASH)	I/O	FRASH MEMORY Writing
62	STAND.CIR_DET	I/O	Detecting SWIVEL PWB
63	SW_L_OUT	I/O	SWIVEL(L-output)
64	SW_R_OUT	I/O	SWIVEL(R-output)
65	M_SW	I/O	Discriminate terminal of bridge media circuit connecting.
66	INITIALIZE	I/O	Initializing EEPROM
67	D.RESET(DARST)	I/O	RESET(DVI)
68	DVI-PD	I/O	DVI Contorol
69	SCDT	I/O	DVI Contorol
70	HS-DJTR	I/O	DVI Contorol
71	DVI-SW	I/O	DVI Contorol
72	CUR_PRTCT	I/O	Detecting Powre-SWIVEL
73	SPRLY	I/O	SP ON/OFF Relay Control
74	MUTE	I/O	MUTE
75	ASEL1	I/O	AUDIO Signal SW
76	ASEL2	I/O	AUDIO Signal SW
77	SDA2	I/O	I2C(NJW1163,AD7414,TA1370)
78	SCL2	I/O	I2C(NJW1163,AD7414,TA1370)
79	D-SUB COMP_SYNC.SW	I/O	SYNC-SW
80	BM_SW	I/O	BM switch
81	RGB_BLK_2	I/O	NC
82	RGB_BLK_3	I/O	NC
83	AUD RST	I/O	RESET for LIPSYNC IC
84	PDP_WVGA_LCD_SW_1	I/O	PDP/42WVGA/LCD detection
85	+5.0V	I
86	RGB1_DET	I/O	NC
87	GND	I	GND
88	WSS_1	I/O	NC
89	WSS_2	I/O	NC
90	WSS_3	I/O	NC
91	TV.AFC(S)	I/O	AFC Voltage(Sub TUNER)
92	TV.AFC(M)	I/O	AFC Voltage(Main TUNER)
93	FE_AGC_I(M)	I/O	AGC Voltage(Main TUNER)
94	FE_AGC_I(S)	I/O	AFC Voltage(Sub TUNER)
95	HP_DETECT	I/O	HEAD PHONE DETECT
96	HDMI_DET	I/O	HDMI 5V DET
97	INT_HDMI	I/O	INT(HDMI)
98	NC	I/O	NC
99	COMP_SW	I/O	Component SW Main DSUB
100	DEMP_OUT	I/O	deemphasis control output for HDMI

8

			32PD7800/42PD7800 (PW2)
No.	PIN MANE	I/O	FUNCTION
101	CONTROL	I/O	LCD PANEL
102	SCL0	I/O	I2C-BUS Contorol CLOCK
103	SDA0	I/O	I2C-BUS Contorol DATA
104	SCL3(EEPROM)	I/O	I2C-BUS Contorol CLOCK
105	SDA3(EEPROM)	I/O	I2C-BUS Contorol DATA
106	HDMI_CIR_DET	I/O	Detecting HDMI circuit connection
107	EXT_RESET	I/O	EXTERNAL RESET
108	OSD_CS	I/O	OSD CS
109	FC_ENABLE	I/O	FC ENABLE
110	NC	I/O	NC
111	NC	I/O	NC
112	IRQ_DTT	I/O	DTT IRQ
113	DTT_POWER	I/O	DTT POWER
114	DISPEN	I/O	DISPEN
115	HDMI_A_SW	I/O	HDMI AUDIO SW
116	SCL5	I/O	I2C-BUS Contorol CLOCK
117	SDA5	I/O	I2C-BUS Contorol DATA
118	FUNC_1	I/O	Function 1
119	FUNC_2	I/O	Function 2
120	NC	I/O	NC
121	AD_KEY3	I/O	AD KEY3**
122	AD_KEY2	I/O	AD KEY2*
123	AD_KEY1	I/O	AD KEY1(INPUT)
124	TV.POWER	I/O	POWRE ON/OFF(H:ON L:STANDBY)
125	DIP.DET	I/O	DIP DET
126	POWER_SAVE	I/O	POWRE ON/OFF(L ON(STANDBY POWRE SAVE), H OFF)
127	GND	I	GND
128	FAN_ALARM *1	I/O	FAN ALARM

9

32PD7800/42PD7800 (PW2)

Block diagram

10

32PD7800/42PD7800 (PW2)

6. Adjustment

● How to get to Adjustment mode

Using the front control buttons with the set turned off (standby) can activate it.

Press the SUB-POWER() button, INPUT SELECT() button and button at the same time, and hold for more than 5 seconds.

The set turns on in adjustment mode with OSD.

● Changing data and Selecting Adjustment code

When the set is in adjustment mode, the cursor , , , and OK buttons of the remote control or front panel may be used as the adjustment keys.

, buttons are used for selecting adjustment code. , buttons are used for changing data values.

OK button is used for confirming the data.

After finishing the necessary adjustment press MENU button. Adjustment mode is released and the set returns to normal condition.

● Memory Initialize operation

NOTE: The execution of this function returns the adjustment codes to the preset values, therefore, adjustment data will be lost.

Procedure

(1)Enter Adjustment Mode.

(2)Select MEMORY INIT adjustment code (No.658) and change the data value from 0 to 1.

(3)Activate MEMORY INIT by pressing OK button for more than 3 seconds.

(4)Select No.525 and change data value from 1 to 0.

(5)Check that the receiving channel goes to P1. Unit is set to preset values.

11

32PD7800/42PD7800 (PW2)

Service adjustment items by I2C-bus control (MAIN Part)

				: should be adjusted
				should be followed previous data
ADJ	Function		Max. Default		Changed Component
No			value	FORMATTER	VIDEO	TUNER	PDP
	ADJ. Items	Mode		PWB	PWB	PWB	PANEL

0	SUB_CONTRAST (RF)							Main	15	8
1	SUB_CONTRAST (AV1)							Main/Sub Composite mode	15	8
2	SUB_CONTRAST (AV2)							Main/Sub Composite mode	15	8
3	SUB_CONTRAST (AV3)							Main/Sub Composite mode	15	8
4	SUB_CONTRAST (AV4)							Main/Sub Composite mode	15	8
5	SUB_CONTRAST (AV5)							Main/Sub Composite mode	15	8
6	SUB_CONTRAST (RF)							Sub	15	8
7	Sub Color							Main	15	8
8	Sub Color							Sub	15	8
9	TINT RF)							Main	63	33
10	TINT VIDEO)							Main	63	33
11	TINT RF)							Sub	63	33
12	TINT VIDEO)							Sub	63	33
13	AGC adjustment (MFE)							Main	63	50
14	AGC adjustment (SFE)							Sub	63	50
15	AGC INPUT(MFE)							Main	-	-
16	AGC INPUT(SFE)							Sub	-	-
17	Reference Amplitude(RGB_AMP)							RF/VIDEO	254	127
18	Reference Amplitude(RGB_AMP)							PC	254	127
19	Reference Amplitude(RGB_AMP)							Multi Picture mode	254	130
20	Display for Max. Amplitude Level							Main	-	-
21	Display for Max. Amplitude Level							Sub	-	-
22	Offset Value(+/-) of Upper Limit (for FC			:RGB-AMP )				Multi Picture mode	18	2
23	Offset Value(+/-) of Upper Limit (for TB1274:SUB-CONT)							Single Picture mode	18	2
24	Offset Value(+/-) of Upper Limit (for TB1274:Sub Color)								18	2
25	Terget value of White peak Adj.							Single Picture mode	237	235
26	Terget value of Color Level Adj. (for TB1274:Sub Color)								237	235
27	Set Blue Gamma gain On/Off 0:Off, 1:On (For 55V)							For 55V	1	1
28	Contrast mode<Dynamic> SW (TV) 0:Dynamic, 1:Dynamic+Auto							RF	1	1
29	Select for WIDE Mode								1	1
30	PinP Function (for PC)		0:PinP, 1:Infomation1, 2:Infomaiton Split						2	0
31	Black Level(RGB_AMP)							RF/VIDEO	254	127
32	Black Level(RGB_AMP)							PC	254	127
33	Black Level(RGB_AMP)							HDMI	254	127
34	Black Level(RGB_AMP)							For USA NTSC/480i	254	127
35	YNR Input Level	for AV1-5 Mode						RF	7	7
36	YNR Input Level	for AV1-5 Mode						VIDEO	7	7
37	YNR Input Level	for AV1-5 Mode						Scart-RGB(50/60Hz)	7	7
38	YNR Input Level	for AV1-5 Mode						480i/576i	7	7
39	YNR Input Level	for AV1-5 Mode						480p/576p	7	7
40	YNR Input Level	for AV1-5 Mode						1080i-50/60/720p	7	7
41	YNR Input Level for DVI-STV Mode							480i/480p/576i/576p/VGA	7	7
42	YNR Input Level	for DVI-STV Mode						1080i-50/60/720p	7	7
43	CNR Input Level at Low level for AV1-5 Mode							RF/VIDEO	7	3
44	CNR Input Level at Low level for AV1-5 Mode							Scart-RGB(50/60Hz)	7	3
45	CNR Input Level at Low level for AV1-5 Mode							480i/576i	7	3
46	CNR Input Level at Low level for AV1-5 Mode							480p/576p	7	3
47	CNR Input Level at Low level for AV1-5 Mode							1080i-50/60/720p	7	3
48	CNR Input Level at Low level for DVI-STV Mode							480i/480p/576i/576p/VGA	7	2
49	CNR Input Level at Low level for DVI-STV Mode							1080i-50/60/720p	7	2
50	CNR Input Level at Low level for Dsub Comp. Mode							480i/576i	7	2
51	CNR Input Level at Low level for Dsub Comp. Mode							480p/576p	7	2
52	CNR Input Level at Low level for Dsub Comp. Mode							1080i-50/60/720p	7	2
53 main/sub YFRNR level			[MYNRP0]					NTSC/PAL/ Multi picture	7	1
54 main/sub YFRNR level			[MYNRP5]					NTSC/PAL-VIDEO	7	0
55 main/sub YFRNR level			[MYNRP6']					Scart-RGB(50/60Hz)	7	0
56 main/sub YFRNR level			[MYNRP6]					480i/576i	7	0
57 main/sub YFRNR level			[MYNRP7]					480p/576p	7	0
58 main/sub YFRNR level			[MYNRP8]					1080i-50/60/720p	7	0
59 main/sub CFRNR level			[MCNRP0]					NTSC/PAL/	7	2
60 main/sub CFRNR level			[MCNRP5]					NTSC/PAL-VIDEO	7	2
61 main/sub CFRNR level			[MCNRP6']					Scart-RGB(50/60Hz)	7	2
62 main/sub CFRNR level			[MCNRP6]					480i/576i	7	2
63 main/sub CFRNR level			[MCNRP7]					480p/576p	7	2
64 main/sub CFRNR level			[MCNRP8]					1080i-50/60/720p	7	0
65	B-Y/B R-Y/R (VER. Enhancer Gain)			[CVEG0]				NTSC/PAL/480i/576i/ Multi picture	15	15
66	B-Y/B R-Y/R (VER. Enhancer Gain)			[CVEG1]				480p/576p/1080i-50/60/720p	15	9
67	DSB Gain of Vertical for B-Y/B R-Y/R			[CVDSBG0]				NTSC/PAL/480i/576i/ Multi picture	3	0
68	DSB Gain of Vertical for B-Y/B R-Y/R			[CVDSBG1]				480p/576p/1080i-50/60/720p	3	0
69	DSB coring of Vertical for B-Y/B R-Y/R			[CVDSBC0]				NTSC/PAL/480i/576i/ Multi picture	7	0
70	DSB coring of Vertical for B-Y/B R-Y/R			[CVDSBC1]				480p/576p/1080i-50/60/720p	7	0
71	B-Y/B R-Y/R (VRE. Enhancer) CLIP 0:CTI					[CVECLP0]		NTSC/PAL/480i/576i/ Multi picture	1	0
72	B-Y/B R-Y/R (VRE. Enhancer) CLIP 0:CTI					[CVECLP1]		480p/576p/1080i-50/60/720p	1	0
73	Horizontal HPF Peek Freq. SW for B-Y/B,R-Y/R [CHHPF0]							NTSC/PAL/480i/576i/ Multi picture	3	2
74	Horizontal HPF Peek Freq. SW for B-Y/B,R-Y/R [CHHPF1]							480p/576p/1080i-50/60/720p	3	2
75	Horizontal Enhancer Gain for B-Y/B,R-Y/R				[CHEG0]			NTSC/PAL/480i/576i/ Multi picture	15	15
76	Horizontal Enhancer Gain for B-Y/B,R-Y/R				[CHEG1]			480p/576p/1080i-50/60/720p	15	9
77	Horizontal DSB Gain for B-Y/B,R-Y/R				[CHDSBG0]			NTSC/PAL/480i/576i/ Multi picture	3	0
78	Horizontal DSB Gain for B-Y/B,R-Y/R				[CHDSBG1]			480p/576p/1080i-50/60/720p	3	0
79	Horizontal DSB Coring for B-Y/B,R-Y/R				[CHDSBC0]			NTSC/PAL/480i/576i/ Multi picture	7	0
80	Horizontal DSB Coring for B-Y/B,R-Y/R				[CHDSBC1]			480p/576p/1080i-50/60/720p	7	0
81	Horizontal Enhancer Clip for B-Y/B,R-Y/G				0:CTI		[CHECLP0]	NTSC/PAL/480i/576i/ Multi picture	1	0
82	Horizontal Enhancer Clip for B-Y/B,R-Y/G				0:CTI		[CHECLP1]	480p/576p/1080i-50/60/720p	1	0
83	B-Y Clamp offset							NTSC/PAL/480i/576i/480p/576p	255	128
84	R-Y Clamp offset							NTSC/PAL/480i/576i/480p/576p	255	128
85	B-Y Clamp offset							1080i-50/60	255	128
86	R-Y Clamp offset							1080i-50/60	255	128
87	B-Y Clamp offset							720p	255	128
88	R-Y Clamp offset							720p	255	128
89	B-Y Clamp offset [DVI-STB]							480i/576i/480p/576p/VGA	255	128
90	R-Y Clamp offset [DVI-STB]							480i/576i/480p/576p/VGA	255	128
91	B-Y Clamp offset [DVI-STB]							1080i-50/60	255	128
92	R-Y Clamp offset [DVI-STB]							1080i-50/60	255	128
93	B-Y Clamp offset [DVI-STB]							720p	255	128
94	R-Y Clamp offset [DVI-STB]							720p	255	128
95	P/N ID							Main	1	0
96	P/N ID							Sub	1	0
97	Sharpness Gain(RF/NR)							Main/Sub	15	2
98	Free

12

32PD7800/42PD7800 (PW2)

										: should be adjusted
										should be followed previous data
ADJ				Function				Max.	Default		Changed Component
No								value		FORMATTER	VIDEO	TUNER	PDP
				ADJ. Items		Mode				PWB	PWB	PWB	PANEL
99	Free
100	Free
101	Free
102	Free
103	Free
104	Free
105	Free
106	Free
107	Free
108	Free
109	Free
110	Sharpness Gain(RF)		BG/DK/I		Sub			15	8
111	Sharpness Gain(RF)		M		Sub			15	8
112	Sharpness Gain(RF)		L		Sub			15	8
113	Sharpness Gain(RF)		L'		Sub			15	8
114	Sharpness Gain(VIDEO)			PAL	Sub			15	8
115	Sharpness Gain(VIDEO)			NTSC3.58	Sub			15	8
116	Sharpness Gain(VIDEO)			SECAM,B/W	Sub			15	8
117	Sharpness Gain(VIDEO)			NTSC4.43	Sub			15	8
118	Sharpness Gain(VIDEO)			N-PAL	Sub			15	8
119	Sharpness Gain(VIDEO)			M-PAL	Sub			15	8
120	Sharpness Gain(S.VIDEO)				Sub			15	10
121	Free
122	Sharpness f0(RF)		BG/DK/I		Main/Sub			3	2
123	Sharpness f0(RF)		M		Main/Sub			3	2
124	Sharpness f0(RF)		L		Main/Sub			3	2
125	Sharpness f0(RF)		L'		Main/Sub			3	2
126	Sharpness f0(VIDEO)		PAL		Main/Sub			3	2
127	Sharpness f0(VIDEO)		NTSC3.58		Main/Sub			3	2
128	Sharpness f0(VIDEO)		SECAM,B/W		Main/Sub			3	2
129	Sharpness f0(VIDEO)		NTSC4.43		Main/Sub			3	2
130	Sharpness f0(VIDEO)		N-PAL		Main/Sub			3	2
131	Sharpness f0(VIDEO)		M-PAL		Main/Sub			3	2
132	Free
133	Y Out Level M	(4.5)			Main			63	15
134	Y Out Level B/G (5.5)				Main			63	13
135	Y Out Level D/K (6.5)				Main			63	16
136	Y Out Level I	(6.0)			Main			63	14
137	Y Out Level L	(6.5)			Main			63	13
138	Y Out Level L'	(6.5)			Main			63	16
139	Y Out Level (VIDEO)				Main			63	15
140	Y Out Level (TEXT)				Main			63	15
141	Free
142	Y Out Level M	(4.5)			Sub			63	19
143	Y Out Level B/G (5.5)				Sub			63	13
144	Y Out Level D/K (6.5)				Sub			63	12
145	Y Out Level I	(6.0)			Sub			63	13
146	Y Out Level L	(6.5)			Sub			63	12
147	Y Out Level L'	(6.5)			Sub			63	15
148	Y Out Level (VIDEO)				Sub			63	13
149	Y Out Level (TEXT)				Sub			63	15
150	Free
151	C Out Level M	(4.5)			Main			63	7
152	C Out Level B/G (5.5)				Main			63	7
153	C Out Level D/K (6.5)				Main			63	7
154	C Out Level I	(6.0)			Main			63	5
155	C Out Level L	(6.5)			Main			63	8
156	C Out Level L'	(6.5)			Main			63	8
157	C Out Level (VIDEO)				Main			63	10
158	C Out Level (TEXT)				Main			63	8
159	Free
160	C Out Level M	(4.5)			Sub			63	3
161	C Out Level B/G (5.5)				Sub			63	8
162	C Out Level D/K (6.5)				Sub			63	8
163	C Out Level I	(6.0)			Sub			63	7
164	C Out Level L	(6.5)			Sub			63	7
165	C Out Level L' (6.5)				Sub			63	7
166	C Out Level (VIDEO)				Sub			63	10
167	C Out Level (TEXT)				Sub			63	13
168	Free
169	BPF_Q (4.43MHz)				Main/Sub			3	3
170	BPF_f0 (4.43MHz)				Main/Sub			3	1
171	C_TRAP_SW (COMB=OFF-PAL/NTSC4.43/NTSC3.58)				Main/Sub			1	0
172	LPF				Main/Sub			1	0
173	SECAM D-Trap				Main/Sub			1	1
174	FILTER SW(RF)				Main/Sub			1	0
175	Y_DL (4.5MHz)				Main			10	6
176	Y_DL (5.5MHz PAL/NTSC4.43)				Main			10	4
177	Y_DL (5.5MHz SECAM)				Main			10	0
178	Y_DL (6.0PAL/NTSC4.43)				Main			10	8
179	Y_DL (6.0SECAM)				Main			10	9
180	Y_DL (6.5PAL/NTSC4.43)				Main			10	6
181	Y_DL (6.5SECAM)				Main			10	10
182	Y_DL (L)				Main			10	5
183	Y_DL (L')				Main			10	5
184	Y_DL (VIDEO PAL/NTSC4.43)				Main			10	6
185	Y_DL (VIDEO SECAM)				Main			10	8
186	Y_DL (VIDEO NTSC)				Main			10	6
187	Y_DL (4.5MHz)				Sub			10	5
188	Y_DL (5.5MHz PAL/NTSC4.43)				Sub			10	2
189	Y_DL (5.5MHz SECAM)				Sub			10	0
190	Y_DL (6.0PAL/NTSC4.43)				Sub			10	7
191	Y_DL (6.0SECAM)				Sub			10	5
192	Y_DL (6.5PAL/NTSC4.43)				Sub			10	5
193	Y_DL (6.5SECAM)				Sub			10	5
194	Y_DL (L)				Sub			10	5
195	Y_DL (L')				Sub			10	5
196	Y_DL (VIDEO PAL/NTSC4.43)				Sub			10	5
197	Y_DL (VIDEO SECAM)				Sub			10	5

13

32PD7800/42PD7800 (PW2)

						: should be adjusted
						should be followed previous data
ADJ	Function			Max.	Default		Changed Component
No				value		FORMATTER	VIDEO	TUNER	PDP
	ADJ. Items	Mode				PWB	PWB	PWB	PANEL
198	Y_DL (VIDEO NTSC)	Sub		10	5
199	NTSC Comb(Comb off)	Sub		1	1
200	Cb offset1	Main		15	8
201	Free
202	Cr offset1	Main		15	8
203	Free
204	Cb offset1	Sub		15	8
205	Free
206	Cr offset1	Sub		15	8
207	Free
208	MVM VIDEO)			1	0
209	AFC_GAIN (AV00)			3	0
210	AFC_GAIN (AV1)			3	0
211	AFC_GAIN (AV2)			3	0
212	AFC_GAIN (AV3)			3	0
213	AFC_GAIN (AV4)			3	0
214	AFC_GAIN (AV5)			3	0
215	AFC_GAIN (Except AV00)			3	0
216	S_B-Y_ADJ	Main		15	8
217	S_R-Y_ADJ	Main		15	8
218	S_B-Y_ADJ	Sub		15	8
219	S_R-Y_ADJ	Sub		15	8
220	BELL_f0	Main/Sub		1	0
221	S_INHBT			1	0
222	S_ID			1	0
223	S_GP			3	0
224	S_V_ID			1	0
225	BELL/HPF			3	3
226	HS Phase	Main		1	0
227	HS Phase	Sub		1	0
228	Bandwidth 1	NTSC/PAL/480i/576i		3	2
229	Bandwidth 1	480p/576p		3	2
230	Bandwidth 1	1080i-50/60/720p		3	0
231	Bandwidth 2	NTSC/PAL/480i/576i		3	2
232	Bandwidth 2	480p/576p		3	2
233	Bandwidth 2	1080i-50/60/720p		3	0
234	Sub Contrast 1	Except HDMI		15	0
235	Sub Contrast 1	HDMI		15	0
236	Sub Contrast 2	Except HDMI		15	0
237	Sub Contrast 2	HDMI		15	0
238	Sub Color 1	Except HDMI		15	0
239	Sub Color 1	HDMI		15	0
240	Sub Color 2	Except HDMI		15	0
241	Sub Color 2	HDMI		15	0
242	HV THRU 1	NTSC/PAL/480i/576i/480p/576p		1	0
243	HV THRU 1	1080i-50/60/720p		1	0
244	HV THRU 2	NTSC/PAL/480i/576i/480p/576p		1	0
245	HV THRU 2	1080i-50/60/720p		1	0
246	H_SEP 1	RF/VIDEO		1	0
247	H_SEP 1	480i/576i		1	0
248	H_SEP 1	480p/576p		1	0
249	H_SEP 1	1080i_50		1	0
250	H_SEP 1	1080i_60/720p		1	0
251	H_SEP 2	RF/VIDEO		1	0
252	H_SEP 2	480i/576i		1	0
253	H_SEP 2	480p/576p		1	0
254	H_SEP 2	1080i_50		1	0
255	H_SEP 2	1080i_60/720p		1	0
256	V_SEP 1	RF/VIDEO		1	0
257	V_SEP 1	480i/576i		1	0
258	V_SEP 1	480p/576p		1	0
259	V_SEP 1	1080i_50		1	0
260	V_SEP 1	1080i_60/720p		1	0
261	V_SEP 2	RF/VIDEO		1	0
262	V_SEP 2	480i/576i		1	0
263	V_SEP 2	480p/576p		1	0
264	V_SEP 2	1080i_50		1	0
265	V_SEP 2	1080i_60/720p		1	0
266	AFC MODE 1	RF		3	0
267	AFC MODE 1	VIDEO		3	0
268	AFC MODE 2	RF		3	0
269	AFC MODE 2	VIDEO		3	0
270	N_LVL 1	RF		1	0
271	N_LVL 1	VIDEO		1	0
272	N_LVL 2	RF		1	0
273	N_LVL 2	VIDEO		1	0
274	Free
275	HD POSITION 1	480i/576i		15	0
276	HD POSITION 1	480p/576p		15	0
277	HD POSITION 1	1080i_50		15	0
278	HD POSITION 1	1080i_60/720p		15	0
279	Free
280	HD POSITION 2	480i/576i		15	0
281	HD POSITION 2	480p/576p		15	0
282	HD POSITION 2	1080i_50		15	0
283	HD POSITION 2	1080i_60/720p		15	0
284	Y LPF 1	RF		1	1
285	Y LPF 1	VIDEO		1	1
286	Y LPF 2	RF		1	1
287	Y LPF 2	VIDEO		1	1
288	Gain 1			1	1
289	Gain 2			1	1
290	YCS MODE	NTSC3.58		3	0
291	3D DET			7	7
292	AFC Gain	NTSC3.58		3	0
293	2D-CNR k			3	0
294	2D-CNR Lim			3	0
295	GMCON			1	0
296	Y-NC			1	0

14

32PD7800/42PD7800 (PW2)

								: should be adjusted
								should be followed previous data
ADJ			Function			Max.	Default		Changed Component
No						value		FORMATTER	VIDEO	TUNER	PDP
			ADJ. Items	Mode				PWB	PWB	PWB	PANEL
297	Y-NC Lim					3	0
298	2D-YNR k					3	0
299	2D-YNR Gain					3	0
300	2D-YNR Lim					3	0
301	BLK EXP					3	0
302	CKILL					1	0
303	Output Clamp					1	0
304	Input Clamp auto					1	1
305	Int Clamp Manual					1	0
306	C-ENHA					1	0
307	YC-MIX					1	0
308	dummy308					-	-
309	HSWINV					1	0
310	dummy310					-	-
311	V-ENHA Gain			NTSC3.58		3	2
312	V-ENHA NL			NTSC3.58		3	2
313	H-ENHA Gain			NTSC3.58		3	1
314	3DNR Corr for 3DYCS					1	0
315	Burst ON for 2DYCS????					1	0
316	MDMPL					1	0
317	MDMBL					1	0
318	H-MaskOut					7	0
319	V-MaskOut					7	0
320	Input Y-Delay (Main RF mode)		for 3DYCS			7	4
321	Input Y-Delay (Main Video mode) for 3DYCS					7	4
322	Output-Y-Delay (Main RF Mode)		for 3DYCS			15	8
323	Output-Y-Delay (Main Video Mode) for 3DYCS					15	8
324	V-ENHA Core			NTSC3.58		3	0
325	Input Clamp Key			NTSC3.58		1	1
326	Burst Gate Key			NTSC3.58		1	1
327	Sync sep LPF			NTSC3.58		1	0
328	H-WST			NTSC3.58		7	3
329	HD Amp 1			NTSC3.58		7	6
330	HD Gain V			NTSC3.58		31	13
331	HD Amp 2			NTSC3.58		7	1
332	HD Gain 1			NTSC3.58		31	8
333	HD Amp 3			NTSC3.58		7	5
334	HD Gain 2			NTSC3.58		31	4
335	ACMSLP			NTSC3.58		3	1
336	ACSSLP			NTSC3.58		3	2
337	AYMSLP			NTSC3.58		3	2
338	AYSSLP			NTSC3.58		3	2
339	ACMESET			NTSC3.58		3	3
340	ACMFSET			NTSC3.58		3	3
341	ACSESET			NTSC3.58		3	2
342	ACSFSET			NTSC3.58		3	2
343	AYMESET			NTSC3.58		3	3
344	AYMFSET			NTSC3.58		3	3
345	AYSESET			NTSC3.58		3	1
346	AYSFSET			NTSC3.58		3	3
347	BCMSLP			NTSC3.58		3	3
348	BCSSLP			NTSC3.58		3	3
349	BYMSLP			NTSC3.58		3	3
350	BYSSLP			NTSC3.58		3	2
351	BCMESET			NTSC3.58		3	2
352	BCMFSET			NTSC3.58		3	2
353	BCSESET			NTSC3.58		3	2
354	BCSFSET			NTSC3.58		3	2
355	BYMESET			NTSC3.58		3	3
356	BYMFSET			NTSC3.58		3	3
357	BYSESET			NTSC3.58		3	3
358	BYSFSET			NTSC3.58		3	3
359	BCMUP			NTSC3.58		1	1
360	CECMP			NTSC3.58		7	4
361	CSCMP			NTSC3.58		15	0
362	F1HER			NTSC3.58		3	1
363	F1VER			NTSC3.58		3	1
364	MREF			NTSC3.58		15	2
365	CDEYE			NTSC3.58		3	2
366	YDEYE			NTSC3.58		3	2
367	MDS			NTSC3.58		1	0
368	F-TBC OFF MDMPL			NTSC3.58		1	0
369	REC:C_DEC			Except NTSC3.58		1	0
370	V-ENHA Gain			Except NTSC3.58		3	2
371	V-ENHA NL			Except NTSC3.58		3	1
372	H-ENHA Gain			Except NTSC3.58		3	1
373	3D-CNR Lim for 2DYCS					7	0
374	3D-CNR k	for 2DYCS				3	0
375	3D-CNR Gain for 2DYCS					7	0
376	3D-YNR Lim for 2DYCS					7	0
377	3D-YNR k	for 2DYCS				3	0
378	3D-YNR Gain for 2DYCS					7	0
379	YCS MODE			Except NTSC3.58		3	0
380	AFC Gain			Except NTSC3.58		3	0
381	dummy381					-	-
382	dummy382					-	-
383	V-ENHA Core			Except NTSC3.58		3	0
384	Input Clamp Key			Except NTSC3.58		1	1
385	Burst Gate Key			Except NTSC3.58		1	1
386	Sync sep LPF			Except NTSC3.58		1	0
387	H-WST			Except NTSC3.58		7	3
388	HD Amp 1			Except NTSC3.58		7	6
389	HD Gain V			Except NTSC3.58		31	13
390	HD Amp 2			Except NTSC3.58		7	1
391	HD Gain 1			Except NTSC3.58		31	8
392	HD Amp 3			Except NTSC3.58		7	5
393	HD Gain 2			Except NTSC3.58		31	4
394	ACMSLP			Except NTSC3.58		3	2
395	ACSSLP			Except NTSC3.58		3	2

15

32PD7800/42PD7800 (PW2)

								: should be adjusted
								should be followed previous data
ADJ			Function			Max.	Default		Changed Component
No						value		FORMATTER	VIDEO	TUNER	PDP
			ADJ. Items	Mode				PWB	PWB	PWB	PANEL
396	AYMSLP			Except NTSC3.58		3	0
397	AYSSLP			Except NTSC3.58		3	0
398	ACMESET			Except NTSC3.58		3	3
399	ACMFSET			Except NTSC3.58		3	3
400	ACSESET			Except NTSC3.58		3	2
401	ACSFSET			Except NTSC3.58		3	2
402	AYMESET			Except NTSC3.58		3	3
403	AYMFSET			Except NTSC3.58		3	3
404	AYSESET			Except NTSC3.58		3	1
405	AYSFSET			Except NTSC3.58		3	3
406	BCMSLP			Except NTSC3.58		3	3
407	BCSSLP			Except NTSC3.58		3	3
408	BYMSLP			Except NTSC3.58		3	3
409	BYSSLP			Except NTSC3.58		3	2
410	BCMESET			Except NTSC3.58		3	2
411	BCMFSET			Except NTSC3.58		3	2
412	BCSESET			Except NTSC3.58		3	2
413	BCSFSET			Except NTSC3.58		3	2
414	BYMESET			Except NTSC3.58		3	3
415	BYMFSET			Except NTSC3.58		3	3
416	BYSESET			Except NTSC3.58		3	3
417	BYSFSET			Except NTSC3.58		3	3
418	BCMUP			Except NTSC3.58		1	1
419	CECMP			Except NTSC3.58		7	4
420	CSCMP			Except NTSC3.58		15	0
421	F1HER			Except NTSC3.58		3	1
422	F1VER			Except NTSC3.58		3	1
423	MREF			Except NTSC3.58		15	2
424	CDEYE			Except NTSC3.58		3	2
425	YDEYE			Except NTSC3.58		3	2
426	MDS			Except NTSC3.58		1	0
427	F-TBC OFF MDMPL			Except NTSC3.58		1	0
428	SEPA_LEVEL_DSUB			480i/576i		3	2
429	SEPA_LEVEL_DSUB			480p/576p		3	2
430	SEPA_LEVEL_DSUB			1080i_50		3	2
431	SEPA_LEVEL_DSUB			1080i_60/720p		3	2
432	HD-PHASE_DSUB			480i/576i		63	20
433	HD-PHASE_DSUB			480p/576p		63	20
434	HD-PHASE_DSUB			1080i_50		63	20
435	HD-PHASE_DSUB			1080i_60/720p		63	20
436	Heat APC function (HAPC) available					1	1
437	-select(0:1.0, 1:2.2, 2:2.8)			RF/VIDEO		2	1
438	-select(0:1.0, 1:2.2, 2:2.8)			DVI-PC/DVI-STB/DSUB-RGB		2	1
439	Select for APC function					1	0
440	CCFMD function			RF/VIDEO		1	0
441	CCFMD function			DVI-PC/DVI-STB/DSUB-RGB		1	0
442	NTSC/EBU(CCFORM)			SD(YCbCr)/Scart-RGB		1	0
443	NTSC/EBU(CCFORM)			HD(YPbPr)		1	0
444	NTSC/EBU(CCFORM)			DVI-PC/DVI-STB/DSUB-RGB		1	0
445	Correction for Tracking (DCBON)			RF/VIDEO-Color Temp. Cool		1	1
446	Correction for Tracking (DCBON)			RF/VIDEO-Color Temp. Nor/War		1	1
447	Correction for Tracking (DCBON)			DVI-PC/DVI-STB/DSUB-RGB		1	1
448	Color Temp. Correction					3	2
449	Brightness Limitted Function of PANEL [APSON]					1	1
450	Dynamic	Back Light Correction		For LCD		1	1
451	Dynamic	Contrast Correction				1	1
452	Histogram Color Management					1	1
453	Histogram Gradation Amp.					1	1
454	Histogram Enhancer					1	1
455	Dynamic	Enhancer				1	1
456	FC6 THROUGH 0:OFF, 1:THROUGH ON					1	0
457	APL Enhancer 0:OFF, 1:ON			For Dynamic mode		1	1
458	ATC INPUT RED SELECT					1	0
459	HD/VD OUTPUT LEVEL					1	1
460	ISM Control for WVGA			For WVGA		1	1
461	SWIVEL DEMO ON					-	-
462	WVGA BRIGHTNESS			For WVGA		1	0
463	Black insert function 0:Not available, 1:Available			For LCD Dynamic mode or Day		1	0
464	Dynamic Backlight function 0:No, 1:Yes			For LCD		1	1
465	DVI-STB Setup 0:None VGA/Others Yes, 1:All none 2:All have			DVI-STB		2	0
466	HSYNC De-Jitter		0:Low(Disabled), 1:High(Enabled)	DVI-PC		1	0
467	HSYNC De-Jitter		0:Low(Disabled), 1:High(Enabled)	DVI-STB		1	0
468	dummy468					50	0
469	AUTO_FM/AM (D11-D8)					15	2
470	AUTO_FM/AM (D 7-D0)					254	189
471	A2_THRESHOLD (D11-D8)					15	0
472	A2_THRESHOLD (D 7-D0)					254	112
473	PRE_AM			Except 4.5MHz (Except Dual/Stereo		254	17
				mode)
474	VOL_SCART1 (D15-D8)					254	115
475	VOL_SCART1 (D 7-D5)					7	0
476	PRE_SCART					254	31
477	PRE_FM			4.5MHz(JAPAN)		254	34
478	PRE_FM			4.5MHz(Except BTSC-SAP mode)		254	32
479	PRE_FM			4.5MHz(BTSC-SAP)		254	60
480	PRE_FM			4.5MHz(Except KOREA		254	36
				Dual/Stereo mode)
481	PRE_FM			4.5MHz(KOREA Dual/Stereo)		254	34
482	PRE_FM			Except 4.5MHz(Except Dual/Stereo		254	17
				mode)
483	PRE_FM			Except 4.5MHz(Dual/Stereo mode)		254	27
484	PRE_NICAM					254	57
485	CM_THRESHOLD (D15-D8)					254	0
486	CM_THRESHOLD (D7 -D0)					254	36
487	AGC_LEVEL AGCL					3	0
488	TEXT H sync delay					127	0
489	TEXT V sync delay					127	50
490	TEXT_H_POSITION					254	42
491	TEXT_V_POSITION					254	39

16

32PD7800/42PD7800 (PW2)

									: should be adjusted
									should be followed previous data
ADJ				Function			Max.	Default		Changed Component
No							value		FORMATTER	VIDEO	TUNER	PDP
			ADJ. Items		Mode				PWB	PWB	PWB	PANEL
492	Select for APC output		[Except Europe model]		Main RF		2	1
493	L_PLL.GAIN						1	0
494	dummy494						-	-
495	HDMI EDID WRITE ENABLE				0:Disenable, 1:Enable		1	0
496	BPMA	: Back Porch Mode,Field2					1	1
497	VCORA : VCO range select						3	0
498	CRNTA : change pump current select						7	0
499	TESTA	: Matching Test to allow increment of stability counter.					1	1
500	PRMB	: preamble criteria					31	6
501	HDCP	: HDCP enable criteria					31	12
502	SMPLING				For CCD		255	0
503	POLLING				For CCD		255	15
504	START				For CCD		7	2
505	TIMEOUT				For CCD		30	5
506	STATUS				For CCD		7	2
507	CCD-HP				For CCD		79	40
508	CCD-CLK				For CCD		79	57
509	Horizontal Position of OSD						15	7
510	Vertical Position of OSD						15	7
511	Free
512	Typical Value of Contrast OSD				DYNAMIC		31	31
513	Free
514	Temperature for Fun start (Temp_High)						254	58
515	Temperature for Fun stop (Temp_Low)						254	55
516	Display of internal temperature (Temperature)						125	-
517	Display of Panel map version						255	-
518	Accumulation time for Panel (hours)						65535	-
519	Reset function of accumulation time for WVGA/LCD Panel				0:Normal 1:Reset		1	0
					P.S/S.S
520	Power Save/Screen Saver On/Off Setting at Initialize, Reset and Shipping				0:Off/20m		2	0
					1:On/Off
					2:Off/Off
521	PC Power Save function (0:Impossible, 1:Possible)						1	1
522	Screen Saver-Picture shift amount			0:1pixel 1:2pixel 2:3pixel			2	0
523	Screen Saver-Picture shift Direction 0:dia /1:cross /2:up/down /3:left/right						3	0
524	Waite Time for POWER SAVE function (s)				VIDEO/PC		254	15
525	BURN-IN enable/ disenable				0:Disenable, 1:Enable		1	1
526	BURN-IN mode						2	2
527	Recovery to an error of OSC frequency of Ceramic resonator for timer						62	34
528	dummy528						-	-
529	Set Sound System at Auto mode of Sound Sys. (0:auto, 1:4.5MHz)				Main		1	0
530	Power condition at power save mode of PC mode				0:Keep last condition,		1	0
	after done RESET function				1:Return to normal condition
531	Select Wide mode for Europe model				0:Normal, 1:For service		1	0
	(Normal= 5mode/ For Service= 10 mode)
532	Thermo sensor function available or not 0:None, 1:Yes						1	0
533	Video Input function available or not at RGB1 & RGB2 mode				0:Not Available, 1:Available		1	1
534	dummy534						-	-
535	Remote Function available 0:NO, 1:YES						1	1
536	Key Function available		0:NO, 1:YES				1	1
537	DVI-STB/RGB-COMPONENT Function available 0:NO, 1:YES						1	0
538	Terminal Mode Function available			0:Not Available, 1:Available	RS232C		1	1
539	Select color control (0:Asia, 1:South America)				Main/Sub		1	0
540	Language (Refer to below)						6	0
541	Hotel Mode(0:No, 1:Yes)						2	0
542	Analog Data (0:Keep EEPROM, 1:Not Keep to EEPROM)						1	0
543	Maximum Volume Limit						63	63
544	Power Mode(0:Last mode, 1:Pos1, 2-7:V1-6, 8-9:RGB1-2)						9	0
545	dummy545						-	-
546	Channel Select (0:CCIR, 1:CHINA)						1	0
547	Auto_sound 4.5 (0:Korea, 1:BTSC, 2:Japan)						2	0
548	T/TEXT(0:None, 1:Yes)						1	1
549	dummy549						-	-
550	Channel Preset(0:VESTEL, 1:GIFU, 2:HAMA, 3:HFDM, 4:AUSTRALIA)						4	1
551	V FREQ 60Hz Force (0:None, 1:Yes)						1	0
552	Offset value of adjusted TINT				For COMPAL factory		20	11
553	Use "TINT Offset " 0:No, 1:Yes				For COMPAL factory		1	0
554	PDP-BLK ON/OFF				1:ON, 0:OFF		1	0
555	IIC BUS Data/Clock Open(0:Close, 1:Open)						1	0
556	Protect for Image Retention 0:Off, 1:7%, 2:14%, 3:21%, 4:AUTO				Dynamic mode		4	4
557	Protect for Image Retention 0:Off, 1:7%, 2:14%, 3:21%, 4:AUTO				Natural mode		4	4
558	Protect for Image Retention 0:Off, 1:7%, 2:14%, 3:21%, 4:AUTO				Cinema mode		4	4
559	Dispersion Time of Sustain current			0:2 Times, 1:4 times	For Dynamic mode		1	0
560	Dispersion Time of Sustain current			0:2 Times, 1:4 times	For Natural mode		1	1
561	Dispersion Time of Sustain current			0:2 Times, 1:4 times	For Cinema mode		1	1
562	Dispersion Time of Sustain current			0:2 Times, 1:4 times	For PC mode		1	1
563	Dispersion Time of Sustain current			0:2 Times, 1:4 times	For PC-Movie mode		1	1
564	Q mode 0:Freeze, 1:Move 1, 2:Move 2				For 50Hz[Dynamic] mode		2	1
565	Q mode 0:Freeze, 1:Move 1, 2:Move 2				For 50Hz[Natural] mode		2	1
566	Q mode 0:Freeze, 1:Move 1, 2:Move 2				For 50Hz[Cinema] mode		2	1
567	Q mode 0:Freeze, 1:Move 1, 2:Move 2				For 60Hz[Dynamic] mode		2	1
568	Q mode 0:Freeze, 1:Move 1, 2:Move 2				For 60Hz[Natural] mode		2	1
569	Q mode 0:Freeze, 1:Move 1, 2:Move 2				For 60Hz[Cinema] mode		2	1
570	Q mode 0:Freeze, 1:Move 1, 2:Move 2				For 70Hz(PC)		2	0
571	dummy571						-	-
572	dummy572						-	-
573	dummy573						-	-
574	dummy574						-	-
575	dummy575						-	-
576	Gray level of BM				Index		31	4
577	Display of BM version						127	-
578	TA1391: SYNC SW Change				0:SYNC, 1:HDVD1&2		1	0
579	Free
580	Free
581	Counting time for discrimination of fH(M30625/TA1370)						31	2
582	Counting time for discrimination of fV(M30625/TA1370)						31	2
583	Counting time for discrimination of fV(TB1274)						31	2
584	Lower Limits value for Sync Detect of 2ms interval				For AFC at TV mode		254	25
585	Lower Limits value for Sync Detect of 2ms interval				For Free Running at TV mode		254	30

17

32PD7800/42PD7800 (PW2)

							: should be adjusted
							should be followed previous data
ADJ		Function			Max.	Default		Changed Component
No					value		FORMATTER	VIDEO	TUNER	PDP
		ADJ. Items	Mode				PWB	PWB	PWB	PANEL
586	Lower Limits value for Sync Detect of 2ms interval		For AUTO OFF at TV mode		254	25
587	Lower Limits value for Sync Detect of 2ms interval		For Free Running at AV mode		254	30
588	Lower Limits value for Sync Detect of 2ms interval		For Power Save at AV mode		254	5
589	Upper Limits Value for Sync Detect of 2ms interval		For AFC at TV mode		254	40
590	Upper Limits Value for Sync Detect of 2ms interval		For Free Running at TV mode		254	45
591	Upper Limits Value for Sync Detect of 2ms interval		For AUTO OFF at TV mode		254	35
592	Upper Limits Value for Sync Detect of 2ms interval		For Free Running at AV mode		254	45
593	Upper Limits Value for Sync Detect of 2ms interval		For Power Save at AV mode		254	200
594	V detection(Format PWB 0:out of range, 128:NO V(or out of spec), 255:interrupt		50/60(Hz)		255	-
595	H detection(Format PWB 0:out of range, 128:NO H(or out of spec), 255:interrupt		15/28/31/33/45(kHz)		255	-
596	V detection(VideoPWB 0:out of range, 128:NO V(or out of spec), 255:interrupt		50/60(Hz)		255	-
597	H detection(Video PWB 0:out of range, 128:NO H(or out of spec), 255:interrupt		15/28/31/33/45(kHz)		255	-
598	COLOR SYSTEM CONTROL-MODE(0:BW, 2:3.58NTSC, 3:4.43NTSC, )		Main		-	-
599	COLOR SYSTEM CONTROL-MODE(0:BW, 2:3.58NTSC, 3:4.43NTSC, )		Sub		-	-
600	Counting Value of 2ms Sync.Detect		Main		-	-
601	Counting Value of 2ms Sync.Detect		Sub		-	-
602	TB1274 Read Data(00h)		Main		-	-
603	TB1274 Read Data(01h)		Main		-	-
604	TB1274 Read Data(00h)		Sub		-	-
605	TB1274 Read Data(01h)		Sub		-	-
606	MSP Read Data (CNTROL	) (D15-D8)			-	-
607	MSP Read Data (CNTROL	) (D 7-D0)			-	-
608	MSP Read Data (STANDARD_RES) (D15-D8)				-	-
609	MSP Read Data (STANDARD_RES) (D 7-D0)				-	-
610	MSP Read Data (STATUS	) (D15-D8)			-	-
611	MSP Read Data (STATUS	) (D 7-D0)			-	-
612	TA1391FG Read Data(00h)				-	-
613	TA1391FG Read Data(01h)				-	-
614	TA1391FG Read Data(02h)				-	-
615	TA1391FG Read Data(03h)				-	-
616	TA1391FG Read Data(04h)				-	-
617	TA1391FG Read Data(05h)				-	-
618	TA1391FG Read Data(06h)				-	-
619	TA1391FG Read Data(07h)				-	-
620	TA1370G Read Data(00h)				-	-
621	TA1370G Read Data(01h)				-	-
622	SiI9993 Read Data SYNC1 : VSYNC/Clock detect/Sync detect 1				-	-
623	SiI9993 Read Data NHRDL1 : N hardware value 1				-	-
624	SiI9993 Read Data NHRDM1 : N hardware value 1				-	-
625	SiI9993 Read Data NHRDH1 : N hardware value 1				-	-
626	SiI9993 Read Data CHRDL1 : CTS hardware value 1				-	-
627	SiI9993 Read Data CHRDM1 : CTS hardware value 1				-	-
628	SiI9993 Read Data CHRDH1 : CTS hardware value 1				-	-
629	SiI9993 Read Data ACR1	: ACR PLL hardware value 1			-	-
630	SiI9993 Read Data ACRS1 : ACR PLL hardware value 1				-	-
631	SiI9993 Read Data SFREQ1 : "Extracted Sampling Frequency 1				-	-
	channel status b24-27(same value at 0x30)"
632	SiI9993 Read Data CLKFRQ1: Clock Accuracy/Sampling Frequency 1				-	-
633	SiI9993 Read Data ALNG1 : Audio length/Audio length max 1				-	-
634	SiI9993 Read Data MT_MD1 : AV mute/HDMI mode 1				-	-
635	SiI9993 Read Data VTYP1 : AVI infoframe type code 1				-	-
636	SiI9993 Read Data VVER1 : AVI infoframe version code 1				-	-
637	SiI9993 Read Data VINFO11: AVI infoframe data 1				-	-
638	SiI9993 Read Data VINFO21:				-	-
639	SiI9993 Read Data VINFO31:				-	-
640	SiI9993 Read Data VINFO41:				-	-
641	SiI9993 Read Data VINFO51:				-	-
642	SiI9993 Read Data ATYP1 : AUDIO InfoFrame Type Code 1				-	-
643	SiI9993 Read Data AVER1 : AUDIO InfoFrame Version Code 1				-	-
644	SiI9993 Read Data AINFO11: AUDIO InfoFrame Data Bytes 1				-	-
645	SiI9993 Read Data AINFO21:				-	-
646	SiI9993 Read Data AINFO31:				-	-
647	SiI9993 Read Data AINFO41:				-	-
648	SiI9993 Read Data AINFO51:				-	-
649	Initialize function for EEPROM of Video PWB board				1	0
650	Check condition of EEPROM of Video PWB board		0:Normal, 1:Abnormal(Fail or no		1	-
			assembly)
651	W/B Initialize				1	-
652	Gain adjustment of RGB amplifier (FLAON)		Main		-	-
653	Gain adjustment of RGB amplifier		Sub		-	-
654	Automatic White Peak Adj.		Single Picture mode		-	-
655	Automatic Color Level Adj. (TB1274BF)		Main PAL/NTSC(COMPOSITE		-	-
656	Automatic Color Level Adj. (TB1274BF)		Sub PAL/NTSC(COMPOSITE		-	-
657	Automatic White Peak Adj.		Multi Picture mode		-	-
658	EEPROM Initialize(0:No, 1:Yes)				1	0
659	Enter to SUB adjust menu				-	-
660	Enter to service menu of FC sub mi-con				-	-

18

32PD7800/42PD7800 (PW2)

Service adjustment items by I2C-bus control (SUB adjust menu)

(*The change to a sub menu. press “ok” key after no.659 with a main menu)								should be adjusted
								should be followed previous data
ADJ			Function			Max.	Default	Changed Component
No.						Value		FORMATTER	VIDEO	TUNER	PDP
			ADJ. Items	Mode				PWB	PWB	PWB	PANEL
0	R DRIVE1 [RF/VIDEO/DSUB-COMP]			COOL		255	255
1	G DRIVE1 [RF/VIDEO/DSUB-COMP]			COOL		255	255
2	B DRIVE1 [RF/VIDEO/DSUB-COMP]			COOL		255	255
3	R DRIVE2 [RF/VIDEO/DSUB-COMP]			NORMAL		255	255
4	G DRIVE2 [RF/VIDEO/DSUB-COMP]			NORMAL		255	255
5	B DRIVE2 [RF/VIDEO/DSUB-COMP]			NORMAL		255	255
6	R DRIVE3 [RF/VIDEO/DSUB-COMP]			WARM		255	255
7	G DRIVE3 [RF/VIDEO/DSUB-COMP]			WARM		255	255
8	B DRIVE3 [RF/VIDEO/DSUB-COMP]			WARM		255	255
9	R DRIVE4 [RF/VIDEO/DSUB-COMP]			BLACK & WHITE		255	255
10	G DRIVE4 [RF/VIDEO/DSUB-COMP]			BLACK & WHITE		255	255
11	B DRIVE4 [RF/VIDEO/DSUB-COMP]			BLACK & WHITE		255	255
12	R DRIVE1 [DVI-PC/DVI-STB/DSUB-RGB]			COOL		255	255
13	G DRIVE1 [DVI-PC/DVI-STB/DSUB-RGB]			COOL		255	255
14	B DRIVE1 [DVI-PC/DVI-STB/DSUB-RGB]			COOL		255	255
15	R DRIVE2 [DVI-PC/DVI-STB/DSUB-RGB]			NORMAL		255	255
16	G DRIVE2 [DVI-PC/DVI-STB/DSUB-RGB]			NORMAL		255	255
17	B DRIVE2 [DVI-PC/DVI-STB/DSUB-RGB]			NORMAL		255	255
18	R DRIVE3 [DVI-PC/DVI-STB/DSUB-RGB]			WARM		255	255
19	G DRIVE3 [DVI-PC/DVI-STB/DSUB-RGB]			WARM		255	255
20	B DRIVE3 [DVI-PC/DVI-STB/DSUB-RGB]			WARM		255	255
21	R DRIVE4 [DVI-PC/DVI-STB/DSUB-RGB]			BLACK & WHITE		255	255
22	G DRIVE4 [DVI-PC/DVI-STB/DSUB-RGB]			BLACK & WHITE		255	255
23	B DRIVE4 [DVI-PC/DVI-STB/DSUB-RGB]			BLACK & WHITE		255	255
24	Brightness Center (CM)			NTSC/PAL/ Multi picture		254	128
25	Brightness Center (CM)			Scart-RGB(50/60Hz)		254	128
26	Brightness Center (CM)			480i/576i/480p/576p		254	128
27	Brightness Center (CM)			1080i-50/60/720p		254	124
28	Brightness Center (CM)			DVI-PC		254	128
29	Brightness Center (CM)			DVI-STB		254	128
30	Brightness Center (CM)			DSUB-RGB		254	128
31	Brightness Center (CM)			Expand DSUB-RGB (Reserved)		254	128
32	Brightness Center (CM)			HDMI		254	128
33	Brightness center (CM) offset			AV1		254	127
34	Brightness center (CM) offset			AV2		254	127
35	Brightness center (CM) offset			AV3		254	127
36	Brightness center (CM) offset			AV4		254	127
37	Brightness center (CM) offset			AV5		254	127
38	Brightness center (CM) offset			DSUB-COMP		254	126
39	Color Center (CM)			SD(YCbCr)(50Hz)		127	72
40	Color Center (CM)			SD(YCbCr)(60Hz)		127	68
41	Color Center (CM)			Scart-RGB(50/60Hz)		127	50
42	Color Center (CM)			HD(YPbPr)(50/60Hz)		127	70
43	Color Center (CM)			DVI-PC		127	64
44	Color Center (CM)			DVI-STB (480i/576i/480p/576p)		127	62
45	Color Center (CM)			DVI-STB (1080i-50/60/720p)		127	62
46	Color Center (CM)			DVI-STB (VGA)		127	62
47	Color Center (CM)			DSUB-RGB		127	64
48	Tint Center (CM)			PAL		254	125
49	Tint Center (CM)			Scart-RGB(50Hz)		254	140
50	Tint Center (CM)			Scart-RGB(60Hz)		254	120
51	Tint Center (CM)			SD(YCbCr)(50Hz)		254	123
52	Tint Center (CM)			SD(YCbCr)(60Hz)		254	130
53	Tint Center (CM)			HD(YPbPr)(50/60Hz)		254	135
54	Tint Center (CM)			DVI-PC		254	128
55	Tint Center	(CM)		DVI-STB (480i/576i/480p/576p)		254	128
56	Tint Center	(CM)		DVI-STB (1080i-50/60/720p)		254	128
57	Tint Center (CM)			DVI-STB (VGA)		254	128
58	Tint Center (CM)			DSUB-RGB		254	128
59	Center of Sharpness (Y-Enhancer Gain for HV)			RF		31	10
60	Center of Sharpness (Y-Enhancer Gain for HV)			VIDEO		31	15
61	Center of Sharpness (Y-Enhancer Gain for HV)			Scart-RGB(50/60Hz)		31	14
62	Center of Sharpness (Y-Enhancer Gain for HV)			480i/576i		31	10
63	Center of Sharpness (Y-Enhancer Gain for HV)			480p/576p		31	15
64	Center of Sharpness (Y-Enhancer Gain for HV)			720p		31	6
65	Center of Sharpness (Y-Enhancer Gain for HV)			1080i-50/60		31	10
66	Center of Sharpness (Y-Enhancer Gain for HV)			TEXT(for split)		31	19
67	Center of Sharpness (Y-Enhancer Gain for HV)			DVI-STB (480i/576i)		31	14
68	Center of Sharpness (Y-Enhancer Gain for HV)			DVI-STB (480p/576p)		31	10
69	Center of Sharpness (Y-Enhancer Gain for HV)			DVI-STB (720p)		31	6
70	Center of Sharpness (Y-Enhancer Gain for HV)			DVI-STB (1080i-50/60)		31	10
71	Center of Sharpness (Y-Enhancer Gain for HV)			DVI-STB (VGA)		31	10
72	Contrast Center (CM)			RF		254	137
73	Contrast Center (CM)			AV1		254	137
74	Contrast Center (CM)			AV2		254	137
75	Contrast Center (CM)			AV3		254	137
76	Contrast Center (CM)			AV4		254	137
77	Contrast Center (CM)			AV5		254	137
78	Contrast Center (CM)			DVI-PC		254	128
79	Contrast Center (CM)			DVI-STB (With Setup)		254	149
80	Contrast Center (CM)			DVI-STB (Without Setup)		254	128
81	Contrast Center (CM)			DSUB-RGB		254	128
82	Contrast Center (CM)			Expand DSUB-RGB (Reserved)		254	128
83	Contrast Center (CM)			DSUB-COMP		254	137
84	Maximum Value of Contrast at REAL/NORMAL mode					254	188
85	Offset Value of Contrast data at SPLIT mode					120	53
86	Offset value of gain for Black Stretch function			Except OFF/LOW/HIGH mode		63	32
87	Horizontal Enhance			TEXT		3	3
88	Vertical Enhance			TEXT		3	3
89	Horizontal filter SW		[HHPF0]	NTSC/480i		1	0
90	(Enhancer Gain )		[HHPF1]	PAL/576i		1	0
91		[HHPF2]		480p/576p/1080i-50/60/720p		1	0

19

32PD7800/42PD7800 (PW2)

												should be adjusted
												should be followed previous data
ADJ							Function			Max.	Default	Changed Component
No.										Value		FORMATTER	VIDEO	TUNER	PDP
			ADJ. Items					Mode				PWB	PWB	PWB	PANEL
92	Horizontal Coring Level [HECOR1]							NTSC-RF		15	3
93	(Enhancer Gain )		[HECOR2]					PAL-RF/ Multi picture		15	2
94	[HECOR3]							NTSC-VIDEO		15	1
95	[HECOR4]							PAL-VIDEO		15	1
96	[HECOR5']							Scart-RGB(50/60Hz)		15	0
97	[HECOR5]							480i/576i		15	2
98	[HECOR6]							480p/576p		15	1
99	[HECOR7]							1080i-50/60/720p		15	1
100	[HECORPC]							PC		15	1
101	Vertical Coring Level		[VECOR1]					NTSC-RF		15	1
102	(Enhancer Gain )		[VECOR2]					PAL-RF/ Multi picture		15	8
103	[VECOR3]							NTSC-VIDEO		15	1
104	[VECOR4]							PAL-VIDEO		15	1
105	[VECOR5']							Scart-RGB(50/60Hz)		15	1
106	[VECOR5]							480i/576i		15	0
107	[VECOR6]							480p/576p		15	15
108	[VECOR7]							1080i-50/60/720p		15	15
109	[VECORPC]							PC		15	0
110	Enhancer gain of VH for C							TEXT		31	0
111	Coring Amplitude for Y/G [YC0R0]							NTSC/PAL-RF/ Multi picture		7	7
112	[YC0R1]							NTSC/PAL-VIDEO		7	5
113	[YC0R2]							480i/576i/Scart-RGB(50/60Hz)		7	4
114	[YC0R3]							480p/576p		7	1
115	[YC0R4]							1080i-50/60/720p		7	1
116	[YC0R5]							NTSC/PAL -input		7	4
117	Coring Amplitube for B-Y/B,R-Y/R [CC0R0]							NTSC/PAL/480i/576i/ Multi picture		7	1
118			[CC0R1]					480p/576p/1080i-50/60/720p		7	1
119	YFRNR input Gain(Main) 2pictures [MYNRG0]							HD-except HD		7	1
120	HD-NTSC, HD-PAL (sub)					[MYNRG1]		HD-HD		7	4
121	4pictures [MYNRG2]							NT-* /PAL-*		7	1
122			[MYNRG3]					HD-*		7	4
123	YFRNR input Gain(Sub)					[YCNRG0]		2pictures		7	4
124			[YCNRG1]					4pictures/12pictures		7	1
125	CFRNR input Gain(Main) 2pictures [MCNRG0]							HD-except HD		7	3
126	HD-NTSC, HD-PAL (SUB)					[MCNRG1]		HD-HD		7	4
127			[MCNRG2]					NT-* /PAL-*		7	4
128			[MCNRG3]					HD-*		7	4
129	CFRNR input Gain(Sub)					[SCNRG0]		2pictures		7	3
130			[SCNRG1]					4pictures/12pictures		7	4
131	Vertical Enhancer Gain for Y/G					[YVEG0]		NTSC/PAL(-except RF)/480i/576i		15	15
132			[YVEG1]					480p/576p		15	4
133			[YVEG2]					1080i-50/60/720p		15	15
134			[YVEG3]					PAL(-RF)/ Multi picture		15	15
135	Vertical DSB Gain for Y/G			[YVDSBG0]				NTSC/PAL/480i/576i/ Multi picture		3	3
136			[YVDSBG1]					480p/576p		3	0
137			[YVDSBG2]					1080i-50/60/720p		3	2
138	Vertical DSB Coring for Y/G			[YVDSBC0]				NTSC/PAL/480i/576i/ Multi picture		7	7
139			[YVDSBC1]					480p/576p/1080i-50/60/720p		7	0
140	Vertical Enhancer Clip for Y/G				0:LTI		[YVECLP0]	NTSC/PAL/480i/576i/ Multi picture		1	1
141			[YVECLP1]					480p/576p/1080i-50/60/720p		1	0
142	Vertical Clip Offset Level			[YVECLPL0]				NTSC/PAL/480i/576i/ Multi picture		15	15
143			[YVECLPL1]					480p/576p/1080i-50/60/720p		15	8
144	Vertical Non Linear Peaking for Y/G [YVNLP0]							NTSC/PAL/480i/576i/ Multi picture		63	0
145			[YVNLP1]					480p/576p/1080i-50/60/720p		63	0
146	Horizontal Enhancer Gain for Y/R					[YHEG0]		NTSC/PAL(-except RF)/480i/576i		15	15
147			[YHEG1]					480p/576p		15	15
148			[YHEG2]					1080i-50/60/720p		15	15
149			[YHEG3]					PAL(-RF)/ Multi picture		15	15
150	Horizontal DSB Gain for Y/R			[YHDSBG0]				NTSC/PAL/480i/576i/ Multi picture		3	2
151			[YHDSBG1]					480p/576p		3	0
152			[YHDSBG2]					1080i-50/60/720p		3	2
153	Horizontal DSB Coring for Y/R				[YHDSBC0]			NTSC/PAL/480i/576i/ Multi picture		7	7
154			[YHDSBC1]					480p/576p/1080i-50/60/720p		7	7
155	Horizontal Enhancer Clip for Y/R					0:LTI	[YHDSBC0]	NTSC/PAL/480i/576i/ Multi picture		1	0
156			[YHDSBC1]					480p/576p/1080i-50/60/720p		1	0
157	Horizontal Clip Offset Level for Y/R [YHECLPL0]							RF/ Multi picture		15	4
158			[YHECLPL1]					NTSC/PAL-VIDEO		15	4
159			[YHECLPL3]					480i/576i/Scart-RGB(50/60Hz)		15	10
160			[YHECLPL2]					480p/576p/1080i-50/60/720p		15	0
161	Horizontal Non Linear Peaking for Y/G						[YHNLP0]	NTSC/PAL/480i/576i/ Multi picture		63	0
162			[YHNLP1]					480p/576p/1080i-50/60/720p		63	0
163	Horizontal HPF Peak Freq. SW for Y/R [YHHPF0]							NTSC/PAL/480i/576i/ Multi picture		3	2
164			[YHHPF1]					480p/576p		3	2
165			[YHHPF2]					1080i-50/60/720p		3	2
166	Initial value of Contrast							Extend 1 of Panel Life function		127	93
167	Interval time of correction time							Extend 1 of Panel Life function		127	10
168	Additional value of Contrast							Extend 1 of Panel Life function		127	1
169	Initial value of Contrast							Extend 2 of Panel Life function		127	63
170	Interval time of correction time							Extend 2 of Panel Life function		127	6
171	Additional value of Contrast							Extend 2 of Panel Life function		127	1
172	Menu Init. Contrast	(-31[0] +40[71])						For Dynamic		71	62
173	Menu Init. Contrast	(-31[0] +40[71])						For Natural		71	62
174	Menu Init. Contrast	(-31[0] +40[71])						For Cinema		71	51
175	Menu Init. Brightness (-31[0] +31[62])							For Dynamic		62	31
176	Menu Init. Brightness (-31[0] +31[62])							For Natural		62	31
177	Menu Init. Brightness (-31[0] +31[62])							For Cinema		62	33
178	Menu Init. Color	(-31[0] +31[62])						For Dynamic		62	36
179	Menu Init. Color	(-31[0] +31[62])						For Natural		62	31
180	Menu Init. Color	(-31[0] +31[62])						For Cinema		62	21
181	Menu Init. Sharpness		(-15[0] +15[30])					For Dynamic		30	20
182	Menu Init. Sharpness		(-15[0] +15[30])					For Natural		30	15
183	Menu Init. Sharpness		(-15[0] +15[30])					For Cinema		30	10

20

32PD7800/42PD7800 (PW2)

								should be adjusted
								should be followed previous data
ADJ			Function			Max.	Default		Changed Component
No.						Value			FORMATTER	VIDEO	TUNER	PDP
			ADJ. Items	Mode					PWB	PWB	PWB	PANEL
184	Menu Init. Color Temp.(Cool[0]/Normal[1]/Warm[2]/B&W[3])			For Dynamic		3	0
185	Menu Init. Color Temp.(Cool[0]/Normal[1]/Warm[2]/B&W[3])			For Natural		3	1
186	Menu Init. Color Temp.(Cool[0]/Normal[1]/Warm[2]/B&W[3])			For Cinema		3	2
187	Menu Init. Black stretch (Off[0]/Low[1]/Mid.[2]/High[3])			For Dynamic		3	1
188	Menu Init. Black stretch (Off[0]/Low[1]/Mid.[2]/High[3])			For Natural		3	1
189	Menu Init. Black stretch (Off[0]/Low[1]/Mid.[2]/High[3])			For Cinema		3	0
190	Menu Init. YNR (Off[0]/Low[1]/High[2])			For Dynamic		2	0
191	Menu Init. YNR (Off[0]/Low[1]/High[2])			For Natural		2	0
192	Menu Init. YNR (Off[0]/Low[1]/High[2])			For Cinema		2	0
193	Menu Init. LTI (Off[0]/Low[1]/Mid.[2]/High[3])			For Dynamic		3	2
194	Menu Init. LTI (Off[0]/Low[1]/Mid.[2]/High[3])			For Natural		3	1
195	Menu Init. LTI (Off[0]/Low[1]/Mid.[2]/High[3])			For Cinema		3	0
196	Center of Sharpness (HV Enhancer Gain for Y)			HDMI (480i/576i)		31	10
197	Center of Sharpness (HV Enhancer Gain for Y)			HDMI (480p/576p)		31	20
198	Center of Sharpness (HV Enhancer Gain for Y)			HDMI (720p)		31	15
199	Center of Sharpness (HV Enhancer Gain for Y)			HDMI (1080i-50/60)		31	7
200	Center of Sharpness (HV Enhancer Gain for Y)			HDMI (VGA)		31	10
201	Color Center (CM)			HDMI-YCbCr(50Hz:576i/576p)		127	65
202	Color Center (CM)			HDMI-YCbCr(60Hz:480i/480p)		127	65
203	Color Center (CM)			HDMI-YPbPr(1080i-50/60/720p)		127	65
204	Tint Center (CM)			HDMI-YCbCr(50Hz:576i/576p)		254	126
205	Tint Center (CM)			HDMI-YCbCr(60Hz:480i/480p)		254	126
206	Tint Center (CM)			HDMI-YPbPr(1080i-50/60/720p)		254	126
207	Sharpness Gain(RF)	BG/DK/I		Main		15	5(42),8(32)
208	Sharpness Gain(RF)	M		Main		15	8
209	Sharpness Gain(RF)	L		Main		15	8
210	Sharpness Gain(RF)	L'		Main		15	8
211	Sharpness Gain(VIDEO)		PAL	Main		15	8
212	Sharpness Gain(VIDEO)		NTSC3.58	Main		15	10
213	Sharpness Gain(VIDEO)		SECAM,B/W	Main		15	8
214	Sharpness Gain(VIDEO)		NTSC4.43	Main		15	8
215	Sharpness Gain(VIDEO)		N-PAL	Main		15	8
216	Sharpness Gain(VIDEO)		M-PAL	Main		15	8
217	Sharpness Gain(S.VIDEO)			Main		15	8

21

32PD7800/42PD7800 (PW2)

The Expression of input signal mode (format)

PAL1: RF, S and Composite of PAL/SECAM PAL2: Component of PAL (YCBCR)

PAL3: Component of PAL (YPBPR)

PAL4: Component of PAL (YCBCR-SCART)

PAL: PAL1-4

NT1: S and Composite of NTSC NT2: Component of NTSC (YCBCR) NT3: Component of NTSC (YPBPR)

NT4: Component of NTSC (YCBCR-SCART)

NTSC: NTSC1-4

HD1-6: Component (shown in the table) HD7: Component of 1080i/50 (YPBPR) HD8: Component of 1080i/50 (YCBCR) HD9: Component of 576p (YPBPR)

HD10: Component of 576p (YCBCR)

HD: HD1-10 of Component

TV: NTSC / HD

PC: PC signal

	Video	Judgment of	Video Input	Mode
	Input	H.Frequency	Setup
		15.75kHz	Auto	PAL2
		(576i)	SDTV/DVD	PAL2
			HDTV	PAL3
		15.75kHz	Auto	NT2
		(480i)	SDTV/DVD	NT2
			HDTV	NT3
		31.25kHz	Auto	HD10
		(576p)	SDTV/DVD	HD10
			HDTV	HD9
	AV1	31.50kHz	Auto	HD3
		(480p)	SDTV/DVD	HD3
	AV2
			HDTV	HD2
		45.00kHz	Auto	HD5
		(720p)	SDTV/DVD	HD6
			HDTV	HD5
		28.125kHz	Auto	HD7
		(1080i)	SDTV/DVD	HD8
			HDTV	HD7
		33.75kHz	Auto	HD1
		(1080i)	SDTV/DVD	HD4
			HDTV	HD1

Factory Reset

After all of the adjustments of main chassis are finished, perform FACTORY RESET.

Press the SUB-POWER() button, INPUT SELECT() button and button at the same time, and hold for more than 5 seconds.

The unit is set to factory settings.

22

32PD7800/42PD7800 (PW2)

	Item		Power Unit Vs, Va Adjustment
Applicable Model			All models
		Preparation					Procedure
(1)	Turn on the set and perform			(1)	Turn Vs ADJ to adjust Vs voltage
	pre-heat run more than 1 min				to be within ±0.1V of the value
	on burn-in screen.				specified in the label on the panel.
						Adjust within ± 1V at Vs1
						Adjust within ± 0.1V at Vs2
(2)	Receive full back pattern signal			(2)	Turn Va ADJ to adjust Va voltage
	(or Video silence signal;				to be within ±0.2V of the value specified
	but it will be automatically turned off				in the label on the panel.
	after a few seconds by power save function.)					Adjust within ± 1V at Va1
						Adjust within ± 0.2V at Va2
(3)	Connect voltmeter leads to Vs			(3)	Reconfirm that Vs voltage remains within
	(or Va) and GND test points of the power unit.				±0.1V of the specified value.
					Readjust if it’s outside of the margin.
						Label example
						<LOT>N6
						Vs= 80.0V	Va=60.0V
						Vw=140.0V	Vx=60.0V

				Label
		Power
Y-sus				X-sus
		Supply
		Unit

Panel Module (Rear View)

CN99 Vs / Va Test Pin

Vs

Va

GND

Vs1:Vs coarse adjustment VR

Vs2:Vs fine adjustment VR

Va2:Va fine adjustment VR

Va1:Va coarse adjustment VR

Murata MPF7415

S/N ********

MADE IN THAILAND

23

32PD7800/42PD7800 (PW2)

	Item		AGC Adjustment (Main)
Applicable Model			All models
		Preparation					Procedure
(1)	Turn on the set and perform pre-heat run			(1)	Receive AGC adjustment signal.
	more than 20 min.				Indicate Service Adjustment menu (Main).
(2)	Receive AGC adjustment signal.			(2)	Display the following signals at the same time.
	CCIR ch-5: (175.25MHz)				Service Adjustment No.13 (AGC Adjustment)
	PAL B/G PHILIPS				No.15 (AGC Input)
	Field : -50dBm
				(3) Raise No.13 data value until No.15 data is
					saturated(This point: AGC-MAX)
				(4)	With monitoring No.15
					reduce No.13 data value and press [OK] key
					at the point when No.15 data
					comes down.
					AGC Voltage
					AGC Max.
					AGC
					Adj. point

AGC POINT

24

32PD7800/42PD7800 (PW2)

Item			AGC Adjustment (Sub)
Applicable Model			All models
	Preparation						Procedure
(1) Turn on the set and perform pre-heat run				(1)	Receive AGC adjustment signal.
more than 20 min.					Indicate Service Adjustment menu (Sub).
(2) Receive AGC adjustment signal.				(2)	Display the following signals at the same time.
CCIR ch-5: (175.25MHz)					Service Adjustment No.14 (AGC Adjustment)
PAL B/G PHILIPS					No.16 (AGC Input)
Field : -50dBm
				(3) Raise No.14 data value until No.16 data is
					saturated(This point: AGC-MAX)
				(4)	With monitoring No.16
					reduce No.14 data value and press [OK] key
					at the point when No.16 data comes down.
					AGC Voltage
					AGC Max.
					AGC
					Adj. point

AGC POINT

25

32PD7800/42PD7800 (PW2)

	Item		RGB Amplitude Adjustment (PC D-Sub input)
	Applicable Model		All models
		Preparation				Procedure
	(1) Input RGB amplitude adjustment signal of VGA (1)					Receive PC signal (VGA [60Hz]), and indicate
	(60Hz) into RGB2 [D-sub] terminal.					Service Adjustment Menu.(Main)
		(2)				Select No.652 of Service Adjustment Menu.
	Black pattern: Set pedestal level.					Press [OK] key more than 2 seconds to start the
						automatic adjustment.
	Characters must not be inserted
						The adjustment completes when the OSD
	into this signal.
						reappears.

Black White

0.7V

[Note] Never adjust without use of the specified signal.

If that were done by mistake, the picture would become abnormal in black level, contrast and color. In this case, it will be recovered by re-adjustment in the specified way.

Item

RGB Amplitude Adjustment (Main/Sub)

Applicable Model

All models

Preparation

Procedure

(1)

Input 576p or 480p adjustment signal

(1)

Receive 576p or 480p adjustment signal on AV1

into AV1 terminal.

terminal input.

Indicate Service Adjustment Menu.

(2)

Select No.652 (RGB amplitude gain adjustment

Black pattern: Set pedestal level.

Main) of Service Adjustment Menu.

Press [OK] key more than 2 seconds to start the

Characters must not be inserted

automatic adjustment.

into this signal.

The adjustment completes when the indication

[Auto Mode] at the bottom of the screen

disappears.

(3)

Select No.653 (RGB amplitude gain adjustment

Black White

Sub) of Service Adjustment Menu.

Press [OK] key more than 2 seconds to start the

0.7V

automatic adjustment.

The adjustment completes when the indication

[Auto Mode] at the bottom of the screen

disappears.

[Note] Never adjust without use of the specified signal.

If that were done by mistake, the picture would become abnormal in black level, contrast and color. In this case, it will be recovered by re-adjustment in the specified way.

26

32PD7800/42PD7800 (PW2)

	Item		TV/Video Color Amplitude Adjustment (Main/Sub)
Applicable Model			All models
		Preparation			Procedure
(1)	Receive color amplitude adjustment			(1)	Select No.655 (Automatic Color Level Adj.
	signal.				Single) of Service Adjustment Menu.
					Press [OK] key more than 2 seconds to
					start the automatic adjustment.
	Switch to AV1 and receive PAL color
	amplitude adjustment signal.				The adjustment completes when the
					indication [Auto Mode]
					at the bottom side o the screen disappears.
				(2)	Select No.656 (Automatic Color Level Adj.
					Multi) of Service Adjustment Menu.
					Press [OK] key more than 2 seconds to
					start the automatic adjustment.
					The adjustment completes when the
					indication [Auto Mode]
					at the bottom side of the screen disappears.

27

32PD7800/42PD7800 (PW2)

	Item				Video Color Temperature Adjustment (Cool)
Applicable Model					All models
		Adjustment Preparations						Adjustment Procedures
(1)	Set the signal generator output as All White.					(1)	Perform the following adjustment with the remote
							control
(2)	Component signal (480i)					(2)	Set the CRT color analyzer (CA100) at the center
	Video level : 0.700Vp-p						of the panel.
	Sync level : 0.300Vp-p
	Setup level : 0V
(3)	Picture Menu is set as [RESET].					(3)	Ensure that the service adjustment
							menu (sub menu) No. 0, 1, 2, are all set as 255.
(4)	Confirm that the mode is set as Factory					(4)	After receiving the video signal, step down the two
	Adjustment mode.						(or one) among adjustment No. 0, 1, 2 and adjust
							the values as shown below.
							Note)
							At least one of the data shoud be 255.
								Specification
								Video color temperature (Cool)
								x=0.258±0.005
								y=0.273±0.005

28

32PD7800/42PD7800 (PW2)

	Item			Video Color Temperature Adjustment (Normal)
Applicable Model				All models
			Preparation			Procedure
(1)	Set signal generator output as				(1)	Perform the following adjustment with the remote
	All White (Window ratio: 100%).					control.
(2)	Component signal (480i)				(2)	Set the CRT Color Analyzer (CA-100) at the center
	Video level	: 0.700Vp-p				of the panel.
	Sync level	: 0.300Vp-p
	Setup level	: 0V
(3)	Check that Picture Menu is set as [RESET]				(3)	Ensure that service adjustment
	mode.					menu (sub) No. 3, 4, 5 are all set as 255.
(4)	Set into Factory Adjustment mode.				(4)	After receiving the video signal, step down
						the two (or one) among adjustment No. 3, 4, 5 and
						adjust the values as shown below.
						(Note)
						At least one of the data should be 255.
						<Specification>
						Video color Color temperature (Normal)
						x=0.285	0.005
						y=0.293	0.005
	Item			Video Color Temperature Adjustment (Warm)
Applicable Model				All models
			Preparation			Procedure
(1) Set signal generator output as					(1)	Perform the following adjustment with the remote
	All White (Window ratio: 100%).					control.
(2)	Component signal (480i)				(2)	Set the CRT Color Analyzer (CA100) at the center
	Video level	: 0.700Vp-p				of the panel.
	Sync level	: 0.300Vp-p
	Setup level	: 0V
(3) Check that Picture Menu is set as [RESET]					(3) Ensure that service adjustment
	mode.					menu (submenu) No. 6, 7, 8 are all set as 255.
(4) Set into Factory Adjustment mode.					(4)	After receiving the video signal, step down
						the two (or one) among adjustment No. 6, 7, 8 and
						adjust the values as shown below.
						(Note)
						At least one of the data should be 255.
						<Specification>
						Video color Color temperature (Warm)
						x=0.314	0.005
						y=0.327	0.005

29

32PD7800/42PD7800 (PW2)

	Item			Video Color Temperature Adjustment (B&W)
Applicable Model				All models
		Preparation				Procedure
(1)	Set signal generator output as All White				(1)	Perform the following adjustment with
	(Window ratio: 100%).					the remote control.
(2)	Component signal (480i)				(2)	Set the CRT Color Analyzer (CA-100) at
	Video level	: 0.700Vp-p				the center of the panel.
	Sync level	: 0.300Vp-p
	Setup level	: 0V
(3)	Check that Picture Menu is set as				(3)	Ensure that service adjustment
	[RESET] mode.					menu (sub menu) No. 9, 10, 11 are all set as 255.
(4)	Set into Factory Adjustment mode.				(4)	After receiving the video signal, step down
						the two (or one) among adjustment No. 9,
						10, 11 and adjust the values as shown
						below.
						(Note)
						At least one of the data should be 255.
						<Specification>
						Video color Color temperature (B&W)
						x=0.335	0.005
						y=0.343	0.005

Item	PC Color Temperature Adjustment
Applicable Model	All models
	Preparations			Procedures
(1) Perform after the video color temperature		(1)	Perform the following adjustment with the remote
adjustment.			control
(2) Set into Factory Adjustmentmode.		(2)	Write the results of the video color temp.adjustment
			(Dynamic/Normal/Warm/B&W) No. 12, 13, 14, 15,
			16, 17, 18, 19, 20, 21, 22, 23 data into Adjustment
			No. 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11 data.
			* at service Adjustment sub menu.
			Ex.)
			Video adjustment		PC adjustment
			No.0 data	→	No.12 data
			No.1 data	→	No.13 data
			No.2 data	→	No.14 data

30