HIT HD74LV273A Datasheet
HD74LV273A
Octal D-type Flip-Flops with Clear
ADE-205-273 (Z)
1st Edition
April 1999
Description
The HD74LV273A has eight edge trigger D-type flip-flops with clear in a 20-pin package. Data on the D
input having the specified setup and hold times is transferred to the Q output on the low to high transition
of the clock input. The clear input when low, sets all outputs to a low state. Low-voltage and high-speed
operation is suitable for battery-powered products (e.g., notebook computers), and the low-power
consumption extends the battery life.
Features
• VCC = 2.0 V to 5.5 V operation
• All inputs VIH (Max.) = 5.5 V (@VCC = 0 V to 5.5 V)
• All outputs VO (Max.) = 5.5 V (@VCC = 0 V)
• Typical VOL ground bounce < 0.8 V (@VCC = 3.3 V, Ta = 25°C)
• Typical VOH undershoot > 2.3 V (@VCC = 3.3 V, Ta = 25°C)
• Output current ±6 mA (@VCC = 3.0 V to 3.6 V), ±16 mA (@VCC = 4.5 V to 5.5 V)
Function Table
Inputs
CLR CLK D Output Q
LXXL
H ↑ HH
H ↑ LL
H ↓ XQ
Note: H: High level
L: Low level
X: Immaterial
↑: Low to high transition
↓: High to low transition
Q
: Output level before the indicated steady state input conditions were established.
0
0
HD74LV273A
Pin Arrangement
CLR
V
1
20
CC
1Q
1D
2D
2Q
3Q
3D
4D
4Q
GND
10
2
3
4
5
6
7
8
9
(Top view)
19
18
17
16
15
14
13
12
11
8Q
8D
7D
7Q
6Q
6D
5D
5Q
CLK
2
HD74LV273A
Absolute Maximum Ratings
Item Symbol Ratings Unit Conditions
Supply voltage range V
Input voltage range*
Output voltage range*
1
1, 2
Input clamp current I
Output clamp current I
Continuous output current I
Continuous current through
V
or GND
CC
Maximum power dissipation
at Ta = 25°C (in still air)*
3
CC
V
I
V
O
IK
OK
O
or I
I
CC
GND
P
T
Storage temperature Tstg –65 to 150 °C
Notes: The absolute maximum ratings are values which must not individually be exceeded, and furthermore,
no two of which may be realized at the same time.
1. The input and output voltage ratings may be exceeded if the input and output clamp-current
ratings are observed.
2. This value is limited to 5.5 V maximum.
3. The maximum package power dissipation was calculated using a junction temperature of 150°C.
–0.5 to 7.0 V
–0.5 to 7.0 V
–0.5 to VCC + 0.5 V Output: H or L
–0.5 to 7.0 VCC: OFF
–20 mA VI < 0
±50 mA VO < 0 or VO > V
±25 mA VO = 0 to V
CC
±50 mA
835 mW SOP
757 TSSOP
CC
3
HD74LV273A
Recommended Operating Conditions
Item Symbol Min Max Unit Conditions
Supply voltage range V
Input voltage range V
Output voltage range V
Output current I
CC
I
O
OH
I
OL
Input transition rise or fall rate ∆t /∆v 0 200 ns/V VCC = 2.3 to 2.7 V
Operating free-air temperature Ta –40 85 °C
Note: Unused or floating inputs must be held high or low.
2.0 5.5 V
0 5.5 V
0VCCV H or L
— –50 µAV
—–2 mAV
—–6 V
= 2.0 V
CC
= 2.3 to 2.7 V
CC
= 3.0 to 3.6 V
CC
— –12 VCC = 4.5 to 5.5 V
—50 µAV
= 2.0 V
CC
— 2 mA VCC = 2.3 to 2.7 V
—6 V
—12 V
= 3.0 to 3.6 V
CC
= 4.5 to 5.5 V
CC
0 100 VCC = 3.0 to 3.6 V
020 V
= 4.5 to 5.5 V
CC
Logic Diagram
1D
CLK
CLR
3
11
1D
1Q 1Q
C1
2
R
1
To Seven Other Channels
4
HD74LV273A
DC Electrical Characteristics
• Ta = –40 to 85°C
Item Symbol VCC (V)* Min Typ Max Unit Test Conditions
Input voltage V
Output voltage V
Input current I
Quiescent
IH
V
IL
OH
V
OL
IN
I
CC
supply current
Output leakage
I
OFF
current
Input
C
IN
capacitance
Note: For conditions shown as Min or Max, use the appropriate values under recommended operating
conditions.
2.0 1.5 — — V
2.3 to 2.7 VCC × 0.7 — —
3.0 to 3.6 VCC × 0.7 — —
4.5 to 5.5 VCC × 0.7 — —
2.0 — — 0.5
2.3 to 2.7 — — VCC × 0.3
3.0 to 3.6 — — VCC × 0.3
4.5 to 5.5 — — VCC × 0.3
Min to
VCC – 0.1 — — V IOH = –50 µA
Max
2.3 2.0 — — IOH = –2 mA
3.0 2.48 — — IOH = –6 mA
4.5 3.8 — — IOH = –12 mA
Min to
— — 0.1 IOL = 50 µA
Max
2.3 — — 0.4 IOL = 2 mA
3.0 — — 0.44 IOL = 6 mA
4.5 — — 0.55 IOL = 12 mA
0 to 5.5 — — ±1 µAVI = 5.5 V or GND
5.5 — — 20 µAVI = VCC or GND, IO = 0
0——5 µAVI or VO = 0 V to 5.5 V
3.3 — 2 — pF VI = VCC or GND
5
Loading...