HIT HD74ALVCH16373 Datasheet

HD74ALVCH16373

16-bit Transparent D-type Latches with 3-state Outputs

ADE-205-138A (Z)

2nd. Edition

December 1999

Description

The HD74ALVCH16373 is particularly suitable for implementing buffer registers, I/O ports, bidirectional
bus drivers, and working registers. It can be used as two 8-bit latches or one 16-bit latch. When the latch
enable (LE) input is high, the Q outputs follow the data (D) inputs. When LE is taken low, the Q outputs
are latched at the levels set up at the D inputs. Active bus hold circuitry is provided to hold unused or
floating data inputs at a valid logic level.

Features

• VCC = 2.3 V to 3.6 V

• Typical VOL ground bounce < 0.8 V (@VCC = 3.3 V, Ta = 25°C)

• Typical VOH undershoot > 2.0 V (@VCC = 3.3 V, Ta = 25°C)

• Bus hold on data inputs eliminates the need for external pullup / pulldown resistors

Function Table

Inputs Output Q
OE LE D

LHH H
LHL L
LLX Q
HXX Z

H : High level
L : Low level
X : Immaterial
Z : High impedance
Note: 1. Output level before the indicated steady state input conditions were established.

*1

0

HD74ALVCH16373

Pin Arrangement

1OE

1Q1
1Q2

GND

1Q3
1Q4

V

CC

1Q5
1Q6

GND

1Q7
1Q8

2Q1
2Q2

GND

2Q3
2Q4

V

CC

2Q5
2Q6

GND

2Q7
2Q8

2OE

10
11

12
13
14

15
16

17
18

19

20
21
22
23
24

1LE

1
2

3
4
5

6
7

8

9

48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25

1D1
1D2
GND
1D3
1D4

V

CC

1D5
1D6

GND
1D7

1D8
2D1

2D2
GND
2D3

2D4
V

CC

2D5
2D6

GND
2D7

2D8
2LE

(Top view)

2

HD74ALVCH16373

Absolute Maximum Ratings

Item Symbol Ratings Unit Conditions

Supply voltage V
Input voltage
Output voltage

*1

*1, 2

Input clamp current I
Output clamp current I
Continuous output current I
VCC, GND current / pin ICC or I
Maximum power dissipation

at Ta = 55°C (in still air)

*3

CC

V

I

V

O

IK

OK

O

GND

P

T

Storage temperature Tstg –65 to 150 °C
Notes: Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage

to the device. These are stress ratings only, and functional operation of the device at these or
any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute maximum rated conditions for extended periods may affect device
reliability.

1. The input and output negative voltage ratings may be exceeded if the input and output clamp
current ratings are observed.

2. This value is limited to 4.6 V maximum.

3. The maximum package power dissipation is calculated using a junction temperature of 150°C
and a board trace length of 750 mils.

–0.5 to 4.6 V
–0.5 to 4.6 V
–0.5 to VCC +0.5 V
–50 mA VI < 0

±50 mA VO < 0 or VO > V
±50 mA VO = 0 to V

CC

±100 mA

0.85 W TSSOP

CC

Recommended Operating Conditions

Item Symbol Min Max Unit Conditions

Supply voltage V
Input voltage V
Output voltage V
High level output current I

Low level output current I

CC

I

O

OH

OL

Input transition rise or fall rate ∆t / ∆v 0 10 ns / V
Operating temperature Ta –40 85 °C

Note: Unused control inputs must be held high or low to prevent them from floating.

2.3 3.6 V
0VCCV
0VCCV
— –12 mA VCC = 2.3 V
— –12 VCC = 2.7 V
— –24 VCC = 3.0 V
—12mAV
—12 V
—24 V

= 2.3 V

CC

= 2.7 V

CC

= 3.0 V

CC

3

HD74ALVCH16373

Logic Diagram

1OE

1LE

1D1

2OE

2LE

2D1

1

48

C1

47

1D

To seven other channels

24
25

C1

36

1D

13

2

1Q1

2Q1

To seven other channels

4