HIT HB28C032A6, HB28C016A6 Datasheet

HB28C048A6/HB28C032A6

HB28C016A6

FLASH ATA Card

48 MByte/32 MByte/16 MByte

ADE-203-1190A (Z)

Rev. 1.0

Dec. 1, 2000

Description

HB28C048A6, HB28C032A6, HB28C016A6 are Flash ATA card. This card complies with PC card ATA
standard and is suitable for the usage of data storage memory medium for PC or any other electric equipment.
This card is equipped with Hitachi 128 Mega bit Flash memory. This card is suitable for ISA (Industry
Standard Architecture) bus interface standard, and read/write unit is 1 sector (512 bytes) sequential access.
By using this card it is possible to operate good performance for the system which have PC card slots.

Features

• PC card ATA standard specification
 68 pin two pieces connector and Type II (5 mm)

• 3.3 V/5 V single power supply operation

• ISA standard and Read/Write unit is 512 bytes (sector) sequential access
 Sector Read/Write transfer rate: 8MB/sec burst

• Card density is 48 Mega bytes maximum
 This card is equipped Hitachi 128 Mega bit Flash memory

• 3 variations of mode access
 Memory card mode
 I/O card mode
 True IDE mode

• Internal self-diagnostic program operates at VCC power on

• High reliability based on internal ECC (Error Correcting Code) function

• Data reliability is 1 error in 10

• Auto Sleep Function

–14

bits read.

HB28C048/032/016A6

Card Line Up*

Type No. Card density Capacity*

1

4

Total sectors/

3

card*

Sectors/

2

track*

Number of
head

Number of
cylinder

HB28C048A6 48 MB 48,365,568 byte 94,464 32 4 738
HB28C032A6 32 MB 32,243,712 byte 62,976 32 4 492
HB28C016A6 16 MB 16,121,856 byte 31,488 32 2 246

Notes: 1. These data are written in ID.

2. Total tracks = number of head × number of cylinder.

3. Total sectors/card = sectors/track × number of head × number of cylinder.

4. It is the logical address capacity including the area which is used for file system.

2

HB28C048/032/016A6

Card Pin Assignment

Memory card mode I/O card mode True IDE mode

Pin No. Signal name I/O Signal name I/O Signal name I/O

1 GND — GND — GND —
2 D3 I/O D3 I/O D3 I/O
3 D4 I/O D4 I/O D4 I/O
4 D5 I/O D5 I/O D5 I/O
5 D6 I/O D6 I/O D6 I/O
6 D7 I/O D7 I/O D7 I/O
7 -CE1 I -CE1 I -CE1 I
8 A10 I A10 I A10 I
9 -OE I -OE I -ATASEL I
10——————
11 A9 I A9 I A9 I
12 A8 I A8 I A8 I
13——————
14——————
15 -WE I -WE I -WE I
16 RDY/-BSY O -IREQ O INTRQ O
17 VCC — VCC — VCC —
18——————
19——————
20——————
21——————
22 A7 I A7 I A7 I
23 A6 I A6 I A6 I
24 A5 I A5 I A5 I
25 A4 I A4 I A4 I
26 A3 I A3 I A3 I
27 A2 I A2 I A2 I
28 A1 I A1 I A1 I
29 A0 I A0 I A0 I
30 D0 I/O D0 I/O D0 I/O
31 D1 I/O D1 I/O D1 I/O
32 D2 I/O D2 I/O D2 I/O
33 WP O -IOIS16 O -IOIS16 O

3

HB28C048/032/016A6

Memory card mode I/O card mode True IDE mode

Pin No. Signal name I/O Signal name I/O Signal name I/O

34 GND — GND — GND —
35 GND — GND — GND —
36 -CD1 O -CD1 O -CD1 O
37 D11 I/O D11 I/O D11 I/O
38 D12 I/O D12 I/O D12 I/O
39 D13 I/O D13 I/O D13 I/O
40 D14 I/O D14 I/O D14 I/O
41 D15 I/O D15 I/O D15 I/O
42 -CE2 I -CE2 I -CE2 I
43 -VS1 O -VS1 O -VS1 O
44 -IORD I -IORD I -IORD I
45 -IOWR I -IOWR I -IOWR I
46——————
47——————
48——————
49——————
50——————
51 VCC — VCC — VCC —
52——————
53——————
54——————
55——————
56 -CSEL I -CSEL I -CSEL I
57 -VS2 O -VS2 O -VS2 O
58 RESET I RESET I -RESET I
59 -WAIT O -WAIT O IORDY O
60 -INPACK O -INPACK O -INPACK O
61 -REG I -REG I -REG I
62 BVD2 I/O -SPKR I/O -DASP I/O
63 BVD1 I/O -STSCHG I/O -PDIAG I/O
64 D8 I/O D8 I/O D8 I/O
65 D9 I/O D9 I/O D9 I/O
66 D10 I/O D10 I/O D10 I/O
67 -CD2 O -CD2 O -CD2 O
68 GND — GND — GND —

4

Card Pin Explanation

Signal name Direction Pin No. Description

A10 to A0
(PC Card Memory mode)

A10 to A0
(PC Card I/O mode)

A2 to A0
(True IDE mode)

BVD1
(PC Card Memory mode)

-STSCHG

(PC Card I/O mode)

-PDIAG

(True IDE mode)
BVD2

(PC Card Memory mode)

-SPKR

(PC Card I/O mode)

-DASP

(True IDE mode)

-CD1, -CD2

(PC Card Memory mode)

-CD1, -CD2

(PC Card I/O mode)

-CD1, -CD2

(True IDE mode)

-CE1, -CE2

(PC Card Memory mode)
Card Enable

-CE1, -CE2

(PC Card I/O mode)
Card Enable

-CE1, -CE2

(True IDE mode)

I 8, 11, 12, 22, 23,

24, 25, 26, 27,
28, 29

27, 28, 29 Address bus is A10 to A0. Only A2 to A0 are used,

I/O 63 BVD1 outputs the battery voltage status in the card.

I/O 62 BVD2 outputs the battery voltage status in the card.

O 36, 67 -CD1 and -CD2 are the card detection signals. -CD1

I 7, 42 -CE1 and -CE2 are low active card select signals.

Address bus is A10 to A0. A10 is MSB and A0 is
LSB.

A10 to A3 should be grounded by the host.

This output line is constantly driven to a high state
since a battery is not required for this product.

-STSCHG is used for changing the status of
Configuration and status register in attribute area.

-PDIAG is the Pass Diagnostic signal in Master/Slave
handshake protocol.

This output line is constantly driven to a high state
since a battery is not required for this product.

-SPKR outputs speaker signals. This output line is
constantly driven to a high state since this product
does not support the audio function.

-DASP is the Disk Active/Slave Present signal in the
Master/Slave handshake protocol.

and -CD2 are connected to ground in this card, so
host can detect that the card is inserted or not.

Byte/Word/Odd byte mode are defined by combination
of -CE1, -CE2 and A0.

-CE2 is used for select the Alternate Status Register
and the Device Control Register while -CE1 is the chip
select for the other task file registers.

HB28C048/032/016A6

5

HB28C048/032/016A6

Signal name Direction Pin No. Description

-CSEL

(PC Card Memory mode)

-CSEL

(PC Card I/O mode)

-CSEL

(True IDE mode)

D15 to D0
(PC Card Memory mode)

D15 to D0
(PC Card I/O mode)

D15 to D0
(True IDE mode)

GND
(PC Card Memory mode)

GND
(PC Card I/O mode)

GND
(True IDE mode)

-INPACK

(PC Card Memory mode)

-INPACK

(PC Card I/O mode)
Input Acknowledge

-INPACK

(True IDE mode)

-IORD

(PC Card Memory mode)

-IORD

(PC Card I/O mode)

-IORD

(True IDE mode)

I 56 This signal is not used.

This signal is used to configure this device as a
Master or a Slave when configured in the True IDE
mode. When this pin is grounded, this device is
configured as a Master. When the pin is open, this
device is configured as a Slave.

I/O 41, 40, 39, 38,

37, 66, 65, 64, 6,
5, 4, 3, 2, 32, 31,
30

— 1, 34, 35, 68 Ground

O 60 This signal is not used and should not be connected

I 44 This signal is not used.

Data bus is D15 to D0. D0 is the LSB of the even byte
of the word. D8 is the LSB of the odd byte of the
word.

at the host.
This signal is asserted low by this card when the card

is selected and responding to an I/O read cycle at the
address that is on the address bus during -CE and

-IORD are low. This signal is used for the input data
buffer control.

This signal is not used and should not be connected
at the host.

-IORD is used for control of read data in I/O task file
area. This card does not respond to -IORD until I/O
card interface setting up.

-IORD is used for control of read data in I/O task file
area. This card does not respond to -IORD until True
IDE interface setting up.

6

Signal name Direction Pin No. Description

-IOWR

(PC Card Memory mode)

-IOWR

(PC Card I/O mode)

-IOWR

(True IDE mode)

-OE

(PC Card Memory mode)

-OE

(PC Card I/O mode)

-ATASEL

(True IDE mode)
RDY/-BSY

(PC Card Memory mode)

-IREQ

(PC Card I/O mode)

INTRQ
(True IDE mode)

-REG

(PC Card Memory mode)
Attribute memory select

-REG

(PC Card I/O mode)

-REG

(True IDE mode)

I 45 This signal is not used.

-IOWR is used for control of data write in I/O task file
area. This card does not respond to -IOWR until I/O
card interface setting up.

-IOWR is used for control of data write in I/O task file
area. This card does not respond to -IOWR until True
IDE interface setting up.

I 9 -OE is used for the control of reading register’s data in

attribute area or task file area.

-OE is used for the control of reading register’s data in
attribute area.

To enable True IDE mode this input should be
grounded by the host.

O 16 The signal is RDY/-BSY pin. RDY/-BSY pin turns low

level during the card internal initialization operation at
VCC applied or reset applied, so next access to the
card should be after the signal turned high level.

This signal is active low -IREQ pin. The signal of low
level indicates that the card is requesting software
service to host, and high level indicates that the card
is not requesting.

This signal is the active high Interrupt Request to the
host.

I 61 -REG is used during memory cycles to distinguish

between task file and attribute memory accesses.
High for task file, Low for attribute memory is
accessed.

-REG is constantly low when task file or attribute
memory is accessed.

This input signal is not used and should be connected
to VCC.

HB28C048/032/016A6

7

HB28C048/032/016A6

Signal name Direction Pin No. Description

RESET
(PC Card Memory mode)

RESET
(PC Card I/O mode)

-RESET

(True IDE mode)

VCC
(PC Card Memory mode)

VCC
(PC Card I/O mode)

VCC
(True IDE mode)

-VS1, -VS2

(PC Card Memory mode)

-VS1, -VS2

(PC Card I/O mode)

-VS1, -VS2

(True IDE mode)

-WAIT

(PC Card Memory mode)

-WAIT

(PC Card I/O mode)
IORDY

(True IDE mode)

-WE

(PC Card Memory mode)

-WE

(PC Card I/O mode)

-WE

(True IDE mode)

I 58 This signal is active high RESET pin. If this signal is

asserted high, the card internal initialization begins to
operate. During the card internal initialization
RDY/-BSY is low. After the card internal initialization
RDY/-BSY is high.

This signal is active high RESET pin. If this signal is
asserted high, the card internal initialization begins to
operate. In this mode, RDY/-BSY signal can not be
used, so using Status Register the Ready/Busy status
can be confirmed.

This signal is active low -RESET pin. If this signal is
asserted low, all the register’s in this card are reset.
In this mode, RDY/-BSY signal can not be used, so
using status register the Ready/Busy status can be
confirmed.

— 17, 51 +5 V, +3.3 V power.

O 43, 57 These signals are intended to notify VCC requirement

to host. -VS1 is held grounded and -VS2 is
nonconnected in this card.

O 59 This signal is active low -WAIT pin. In this card this

signal is constantly high level.

This output signal may be used as IORDY. In this
card this signal is constantly high impedance.

I 15 -WE is used for the control of writing register’s data in

attribute memory area or task file area.

-WE is used for the control of writing register’s data in
attribute memory area.

This input signal is not used and should be connected
to VCC by the host.

8

Signal name Direction Pin No. Description

WP
(PC Card Memory mode)
Write Protect

-IOIS16

(PC Card I/O mode)

-IOIS16

(True IDE mode)

O 33 WP is held low because this card does not have write

protect switch.

-IOIS16 is asserted when task file registers are
accessed in 16-bit mode.

This output signal is asserted low when this device is
expecting a word data transfer cycle. Initial mode is
16-bit. If the user issues a Set Feature Command to
put the device in Byte access mode, the card permits
8-bit accesses.

HB28C048/032/016A6

9

HB28C048/032/016A6

Card Block Diagram

VCC

GND

A0 to A10

-CE1,-CE2

-OE/-ATASEL

-WE

-IORD

-IOWR

-REG

RESET/-RESET

-CSEL

D0 to D15

BVD1/-STSCHG/-PDIAG

BVD2/-SPKR/-DASP

RDY/-BSY/-IREQ/INTRQ

WP/-IOIS16

internal V

Controller

CC

Reset IC

X'tal

Flash
memory
bus

Flash memory

Control signal

-INPACK

-WAIT/IORDY

-VS1

-VS2

-CD1

-CD2

Note: -CE1, -CE2, -OE, -WE, -IORD, -IOWR, -REG, RESET, -CSEL, -PDIAG, -DASP pins are

pulled up in card.

-CE1, -CE2, -OE, -WE, -IORD, -IOWR, -REG pins are schmitt trigger type input buffer.

OPEN

10

Card Function Explanation

Register construction

• Attribute region
 Configuration register

• Configuration Option register

• Configuration and Status register

• Pin Replacement register

• Socket and Copy register

 CIS ( C ard I nformation S tructure)

• Task File region
 Data register
 Error register
 Feature register
 Sector Count register
 Sector Number register
 Cylinder Low register
 Cylinder High register
 Drive Head register
 Status register
 Alternate Status register
 Command register
 Device Control register
 Drive Address register

HB28C048/032/016A6

11

HB28C048/032/016A6

Host access specifications

1. Attribute access specifications

When CIS-ROM region or Configuration register region is accessed, read and write operations are executed
under the condition of -REG = "L" as follows. That region can be accessed by Byte/Word/Odd-byte modes
which are defined by PC card standard specifications.

Attribute Read Access Mode

Mode -REG -CE2 -CE1 A0 -OE -WE D8 to D15 D0 to D7

Standby mode × HH×××High-Z High-Z
Byte access (8-bit) L H LLLHHigh-Z even byte

L H L H L H High-Z invalid
Word access (16-bit) L L L × L H invalid even byte
Odd byte access (8-bit) L L H × L H invalid High-Z

Note: ×: L or H

Attribute Write Access Mode

Mode -REG -CE2 -CE1 A0 -OE -WE D8 to D15 D0 to D7

Standby mode × HH×××Don’t care Don’t care
Byte access (8-bit) L H L L H L Don’t care even byte

L H L H H L Don’t care Don’t care
Word access (16-bit) L L L × H L Don’t care even byte
Odd byte access (8-bit) L L H × H L Don’t care Don’t care

Note: ×: L or H

Attribute Access Timing Example

A0 to A10

-REG

-CE2/-CE1

-OE

-WE

D0 to D15

read cycle write cycle

Dout

Din

12

HB28C048/032/016A6

2. Task File register access specifications

There are two cases of Task File register mapping, one is mapped I/O address area, the other is mapped Memory address
area. Each case of Task File register read and write operations are executed under the condition as follows. That area can
be accessed by Byte/Word/Odd Byte mode which are defined by PC card standard specifications.

(1) I/O address map

Task File Register Read Access Mode (1)

Mode -REG -CE2 -CE1 A0 -IORD -IOWR -OE -WE D8 to D15 D0 to D7

Standby mode × HHЧЧЧЧЧHigh-Z High-Z
Byte access (8-bit) L H L L L H H H High-Z even byte

L H L H L H H H High-Z odd byte
Word access (16-bit) L L L × L H H H odd byte even byte
Odd byte access (8-bit) L L H × L H H H odd byte High-Z

Note: ×: L or H

Task File Register Write Access Mode (1)

Mode -REG -CE2 -CE1 A0 -IORD -IOWR -OE -WE D8 to D15 D0 to D7

Standby mode × HHЧЧЧЧЧDon’t care Don’t care
Byte access (8-bit) L H L L H L H H Don’t care even byte

L H L H H L H H Don’t care odd byte
Word access (16-bit) L L L × H L H H odd byte even byte
Odd byte access (8-bit) L L H × H L H H odd byte Don’t care

Note: ×: L or H

Task File Register Access Timing Example (1)

A0 to A10

-REG

-CE2/-CE1

-IORD

- IOWR

D0 to D15

Dout

read cycle write cycle

Din

13

HB28C048/032/016A6

(2) Memory address map

Task File Register Read Access Mode (2)

Mode -REG -CE2 -CE1 A0 -OE -WE -IORD -IOWR D8 to D15 D0 to D7

Standby mode × HHЧЧЧЧЧHigh-Z High-Z
Byte access (8-bit) H H L L L H H H High-Z even byte

H H L H L H H H High-Z odd byte
Word access (16-bit) H L L × L H H H odd byte even byte
Odd byte access (8-bit) H L H × L H H H odd byte High-Z

Note: ×: L or H

Task File Register Write Access Mode (2)

Mode -REG -CE2 -CE1 A0 -OE -WE -IORD -IOWR D8 to D15 D0 to D7

Standby mode × HHЧЧЧЧЧDon’t care Don’t care
Byte access (8-bit) H H L L H L H H Don’t care even byte

H H L H H L H H Don’t care odd byte
Word access (16-bit) H L L × H L H H odd byte even byte
Odd byte access (8-bit) H L H × H L H H odd byte Don’t care

Note: ×: L or H

Task File Register Access Timing Example (2)

A0 to A10

-REG

-CE2/-CE1

-OE

-WE

D0 to D15

read cycle write cycle

Dout

Din

14

HB28C048/032/016A6

3. True IDE Mode

The card can be configured in a True IDE mode of operation. This card is configured in this mode only when the -OE
input signal is asserted GND by the host. In this True IDE mode Attribute Registers are not accessible from the host.

Only I/O operation to the task file and data register are allowed. If this card is configured during power on
sequence, data register are accessed in word (16-bit). The card permits 8-bit accesses if the user issues a Set

Feature Command to put the device in 8-bit mode.

True IDE Mode Read I/O Function

Mode -CE2 -CE1 A0 to A2 -IORD -IOWR D8 to D15 D0 to D7

Invalid mode L L ×××High-Z High-Z
Standby mode H H ×××High-Z High-Z
Data register access H L0LHodd byte even byte
Alternate status access L H 6H L H High-Z status out
Other task file access H L 1-7H L H High-Z data

Note: ×: L or H

True IDE Mode Write I/O Function

Mode -CE2 -CE1 A0 to A2 -IORD -IOWR D8 to D15 D0 to D7

Invalid mode L L ×××don’t care don’t care
Standby mode H H ×××don’t care don’t care
Data register access H L 0 H L odd byte even byte
Control register access L H 6H H L don’t care control in
Other task file access H L 1-7H H L don’t care data

Note: ×: L or H

True IDE Mode I/O Access Timing Example

A0 to A2

-CE

-IORD

-IOWR

-IOIS16

D0 to D15

read cycle write cycle

Dout Din

15

HB28C048/032/016A6

Configuration register specifications

This card supports four Configuration registers for the purpose of the configuration and observation of this
card. These registers can be used in memory card mode and I/O card mode. In True IDE mode, these
registers can not be used.

1. Configuration Option register (Address 200H)

This register is used for the configuration of the card configuration status and for the issuing soft reset to the
card.

bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0

SRESET LevlREQ INDEX
Note: initial value: 00H

Name R/W Function

SRESET
(HOST->)

LevlREQ
(HOST->)

INDEX
(HOST->)

R/W Setting this bit to "1", places the card in the reset state (Card Hard Reset). This

operation is equal to Hard Reset, except this bit is not cleared. Then this bit set to "0",
places the card in the reset state of Hard Reset (This bit is set to "0" by Hard Reset) .
Card configuration status is reset and the card internal initialized operation starts when
Card Hard Reset is executed, so next access to the card should be the same sequence
as the power on sequence.

R/W This bit sets to "0" when pulse mode interrupt is selected, and "1" when level mode

interrupt is selected.

R/W This bits is used for select operation mode of the card as follows.

When Power on, Card Hard Reset and Soft Reset, this data is "000000" for the purpose
of Memory card interface recognition.

INDEX bit assignment

INDEX bit
5 4 3 2 1 0 Card mode Task File register address Mapping mode

0 0 0 0 0 0 Memory card 0H to FH, 400H to 7FFH memory mapped
0 0 0 0 0 1 I/O card xx0H to xxFH contiguous I/O mapped
0 0 0 0 1 0 I/O card 1F0H to 1F7H, 3F6H to 3F7H primary I/O mapped
0 0 0 0 1 1 I/O card 170H to 177H, 376H to 377H secondary I/O mapped

16

HB28C048/032/016A6

2. Configuration and Status register (Address 202H)

This register is used for observing the card state.

bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0

CHGED SIGCHG IOIS8 0 0 PWD INTR 0
Note: initial value: 00H

Name R/W Function

CHGED
(CARD->)

SIGCHG
(HOST->)

IOIS8
(HOST->)

PWD
(HOST->)

INTR
(CARD->)

R This bit indicates that CRDY/-BSY bit on Pin Replacement register is set to "1". When

CHGED bit is set to "1", -STSCHG pin is held "L" at the condition of SIGCHG bit set to
"1" and the card configured for the I/O interface.

R/W This bit is set or reset by the host for enabling and disabling the status-change signal (-

STSCHG pin). When the card is configured I/O card interface and this bit is set to "1", ­STSCHG pin is controlled by CHGED bit. If this bit is set to "0", -STSCHG pin is kept
"H".

R/W The host sets this field to "1" when it can provide I/O cycles only with on 8 bit data bus

(D7 to D0).

R/W When this bit is set to "1", the card enters sleep state (Power Down mode). When this

bit is reset to "0", the card transfers to idle state (active mode). RRDY/-BSY bit on Pin
Replacement Register becomes BUSY when this bit is changed. RRDY/-BSY will not
become Ready until the power state requested has been entered. This card
automatically powers down when it is idle, and powers back up when it receives a
command.

R This bit indicates the internal state of the interrupt request. This bit state is available

whether I/O card interface has been configured or not. This signal remains true until the
condition which caused the interrupt request has been serviced. If interrupts are
disabled by the -IEN bit in the Device Control Register, this bit is a zero.

17

HB28C048/032/016A6

3. Pin Replacement register (Address 204H)

This register is used for providing the signal state of -IREQ signal when the card configured I/O card interface.

bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0

0 0 CRDY/-BSY 0 1 1 RRDY/-BSY 0
Note: initial value: 0CH

Name R/W Function

CRDY/-BSY
(HOST->)

RRDY/-BSY
(HOST->)

4. Socket and Copy register (Address 206H)

This register is used for identification of the card from the other cards. Host can read and write this register.
This register should be set by host before this card's Configuration Option register set.

bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0

0 0 0 DRV# 0 0 0 0
Note: initial value: 00H

R/W This bit is set to "1" when the RRDY/-BSY bit changes state. This bit may also be

written by the host.

R/W When read, this bit indicates +READY pin states. When written, this bit is used for

CRDY/-BSY bit masking.

Name R/W Function

DRV#
(HOST->)

R/W This fields are used for the configuration of the plural cards. When host configures the

plural cards, written the card’s copy number in this field. In this way, host can perform
the card’s master/slave organization.

18

HB28C048/032/016A6

CIS informations

CIS informations are defined as follows. By reading attribute address from "0000 H", card CIS informations
can be confirmed.

Address Data 7 6 5 43210 Description of contents CIS function

000H 01H CISTPL_DEVICE Device info tuple Tuple code
002H 04H TPL_LINK Link length is 4 byte Link to next tuple
004H DFH Device type W

006H 4AH EXT Speed

mantissa
008H 01H 1x 2k units 2k byte of address space Device size
00AH FFH List end marker End of device END marker
00CH 1CH CISTPL_DEVICE_OC Other conditions device info

00EH 04H TPL_LINK Link length is 4 bytes Link to next tuple
010H 02H EXT Reserved V
012H D9H Device type W

014H 01H 1x 2k units 2k byte of address space Device size
016H FFH List end marker End of device END marker
018H 18H CISTPL_JEDEC_C JEDEC ID common memory Tuple code
01AH 02H TPL_LINK Link length is 2 bytes Link to next tuple
01CH DFH PCMCIA’s manufacturer’s JEDEC

ID code
01EH 01H PCMCIA JEDEC device code 2nd byte of JEDEC ID
020H 20H CISTPL_MANFID Manufacturer’s ID code Tuple code
022H 04H TPL_LINK Link length is 4 bytes Link to next tuple
024H 07H Low byte of PCMCIA

manufacturer’s code
026H 00H High byte of PCMCIA

manufacturer’s code

028H 00H Low byte of product code HITACHI code for PC CARD

02AH 00H High byte of product code High byte of product code

Device speed Device type = DH: I/O device
P
S

Speed

exponent

MWAIT 3 V, wait is not used Other conditions info field

CC

Device speed Device type = DH: I/O device
P
S

WPS = 1: No WP
Device speed = 7: ext speed

400 ns if no wait Extended speed

tuple

WPS = 1: No WP
Device speed = 1: 250 ns

Manufacturer’s ID code JEDEC ID of PC Card ATA

HITACHI JEDEC
manufacturer’s ID

Code of 0 because other byte
is JEDEC 1 byte
manufacture’s ID

ATA

Device type, WPS, speed

Tuple code

Device type, WPS, speed

Low byte of manufacturer’s
ID code

High byte of manufacturer’s
ID code

Low byte of product code

19

HB28C048/032/016A6

Address Data 7 6 5 43210 Description of contents CIS function

02CH 15H CISTPL_VERS_1 Level 1 version/product info Tuple code
02EH 15H TPL_LINK Link length is 15h bytes Link to next tuple
030H 04H TPPLV1_MAJOR PCMCIA2.0/JEIDA4.1 Major version
032H 01H TPPLV1_MINOR PCMCIA2.0/JEIDA4.1 Minor version
034H 48H ‘ H ’ Info string 1
036H 49H ‘ I ’
038H 54H ‘ T ’
03AH 41H ‘ A ’
03CH 43H ‘ C ’
03EH 48H ‘ H ’
040H 49H ‘ I ’
042H 00H Null terminator
044H 46H ‘ F ’ Info string 2
046H 4CH ‘ L ’
048H 41H ‘ A ’
04AH 53H ‘ S ’
04CH 48H ‘ H ’
04EH 00H Null terminator
050H 35H ‘ 5 ’ Vender specific strings
052H 2EH ‘ . ’
054H 30H ‘ 0 ’
056H 00H Null terminator
058H FFH List end marker End of device END marker
05AH 21H CISTPL_FUNCID Function ID tuple Tuple code
05CH 02H TPL_LINK Link length is 2 bytes Link to next tuple
05EH 04H TPLFID_FUNCTION = 04H Disk function, may be silicon,

may be removable

060H 01H Reserved R P R = 0: No BIOS ROM

P = 1: Configure card at
power on

PC card function code

System initialization byte

20