Hisense Electric LCDF0098, LCDF0116 User Manual
ES-G154912-2 F
1160102
Important Safety Information
and Warranty Card
Please read this thoroughly and keep it for future reference.
IMPORTANT INFORMATION
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE.
The lightning flash with arrow-head symbol,
within an equilateral triangle, is intended to
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
WARNING:
FCC Regulations state that any unauthorized changes or modications to this equipment not expressly approved by the
manufacturer could void the user's authority to operate this equipment.
CAUTION:
This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other
equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded
cables and connectors for connections.
INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
—
Reorient or relocate the receiving antenna.
—
Increase the separation between the equipment and receiver.
—
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—
Consult the dealer or an experienced radio/TV technician for help.
alert the user to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within a triangle is
intended to alert the user to the presence
of important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
Wireless Radio
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not
possible.
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 56505725 MHz.
This device and it's antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter
except in accordance with FCC multi-transmitter product procedures.
This device is restricted for indoor use.
Important:
Any changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.
1
Devices will not permit operations on channels 120-132 for 11a and 11n/a which overlap the 5600 - 5650 MHz band.
Industry Canada Statement
This Class B digital apparatus complies with CAN ICES-003(B)/NMB-3(B).
Wireless Radio
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not
possible.
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful
interference to co-channel mobile satellite systems.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 56505725 MHz.
This device and its antenna(s) must not be co-located with any other transmitters except in accordance with IC multi-
transmitter product procedures.
Referring to the multi-transmitter policy, multiple-transmitter(s) and module(s) can be operated simultaneously without
reassessment permissive change.
For indoor use only.
Important: Any changes or modications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.
The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that
the equipment still complies with the e.i.r.p. limit.
The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still
complies with the e.i.r.p. limits specied for point-to-point and non-point-to-point operation as appropriate.
Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands
5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820 of the National Electrical Code that
provides guidelines for proper grounding and, in particular, species that the cable ground shall be connected to the
grounding system of the building, as close to the point of cable entry as practical.
2
DEAR SHARP CUSTOMER
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years of trouble-free
operation of your product, please read the Important Safety Instructions carefully before using this product.
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if
improperly handled. This product has been engineered and manufactured with the highest priority on safety. However,
improper use can result in electric shock and/or re. In order to prevent potential danger, please observe the following
instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of
your Liquid Crystal Television, please read the following precautions carefully before using the product.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11.
Only use attachments/accessories specified by the manufacturer.
12.
Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13.
Unplug this apparatus during lightning storms or when unused for long periods of time.
14.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Additional Safety Information
15.
Power Sources—This product should be operated only from the type of power source indicated on the marking label.
If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For
products intended to operate from battery power, or other sources, refer to the operating instructions.
16.
Overloading—Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in
a risk of fire or electric shock.
17.
Object and Liquid Entry—Never push objects of any kind into this product through openings as they may touch
dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on
the product.
18.
Damage Requiring Service—Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions:
a. When the AC cord or plug is damaged,
b. If liquid has been spilled, or objects have fallen into the product,
c. If the product has been exposed to rain or water,
d. If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an improper adjustment of other
controls may result in damage and will often require extensive work by a qualified technician to restore the product
to its normal operation,
e. If the product has been dropped or damaged in any way, and
3
f. When the product exhibits a distinct change in performance - this indicates a need for service.
19. Replacement Parts—When replacement parts are required, be sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
20. Safety Check—Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or
21.
other reproductive harm. For more information: www.watts.com/prop65
22. Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product according to the method
recommended by the manufacturer.
Outdoor Antenna Grounding — If an outside antenna is
connected to the television equipment, be sure the antenna
system is grounded so as to provide some protection
against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of
the mast and supporting structure, grounding of the leadin wire to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection
to grounding electrodes, and requirements for the
grounding electrode.
Water and Moisture — Do not use this product near water
- for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250)
NEC — NATIONAL ELECTRICAL CODE
ANTENNA LEAD
IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
and the like. When using the TV outside, please make sure it is protected against moisture (rain, splashing water).
Never expose to moisture.
Stand — Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can cause
the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket
or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the
manufacturer’s instructions. Use only the mounting hardware recommended by the manufacturer.
Selecting the location — Select a place with no direct sunlight and good ventilation.
Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents and
openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product
on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in
installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the
manufacturer’s instructions are followed.
The front panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact.
Be careful not to be injured by broken glass pieces in case the panel breaks.
Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
The Liquid Crystal panel is a very high technology product with millions of pixels, giving you fine picture details. Occasionally, a
few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does not affect the
performance of your product.
Lightning — For added protection for this television equipment during a lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the equipment due
to lightning and power-line surges.
Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric light
or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care
should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
To prevent fire, never place any type of candle or flames on the top or near the TV set.
To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.
Do not display a still picture for a long time, as this could cause an afterimage to remain.
To prevent fire or shock hazard, apparatus shall not be exposed to dripping or splashing and
no objects filled with liquids, such as vases, shall be placed on the apparatus.
Do not insert foreign objects into the product. Inserting objects in the air vents or other openings may result in fire or
electric shock. Exercise special caution when using the product around children
.
4
Precautions when transporting the TV
When transporting the TV, never carry it by holding or otherwise putting
pressure onto the display. Be sure to always carry the TV by two people holding
it with two hands.
Caring for the cabinet
Use a soft cloth (cotton, flannel, etc.) and gently wipe the surface of the cabinet.
Using a chemical cloth (wet/dry sheet type cloth, etc.) may deform the
components of the main unit cabinet or cause cracking.
Wiping with a hard cloth or using strong force may scratch the surface of the cabinet.
If the cabinet is very dirty, wipe with a soft cloth (cotton, flannel, etc.) soaked in neutral detergent diluted with water
and thoroughly wrung out, and then wipe with a soft dry cloth.
Avoid using benzene, thinner, and other solvents, as these may deform the cabinet and cause the paint to peel off.
Do not apply insecticides or other volatile liquids. Also, do not allow the cabinet to remain in contact with rubber or
vinyl products for a long period of time. Plasticizers inside the plastic may cause the cabinet to deform and cause the
paint to peel off.
Caring for the front panel
Turn off the main power and unplug the AC cord from the wall outlet before
handling.
Gently wipe the surface of the front panel with a soft cloth (cotton, flannel, etc.).
To protect the front panel, do not use a dirty cloth, liquid cleaners, or a chemical
cloth (wet/dry sheet type cloth, etc.). This may damage the surface of the front
panel.
Wiping with a hard cloth or using strong force may scratch the surface of the
front panel.
Use a soft damp cloth to gently wipe the front panel when it is really dirty.(It may scratch the surface of the front panel when wiped
strongly.)
If the front panel is dusty, use an anti-static brush, which is commercially available, to clean it.
To avoid scratching the frame or screen, please use a soft, lint free cloth for cleaning. Approved cleaning cloths are available
directly from Sharp in single (00Z-LCD-CLOTH) or triple (00Z-LCD-CLOTH-3) packs. Call 1-800-BE-SHARP for ordering, or VISIT
http://www.sharpusa.com/SharpDirect.
Disconnect device
Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily
operable.
WARNING
Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death.
Many injuries, particularly to children, can be avoided by taking simple precautions such as:
Using cabinets or stands recommended by the manufacturer of the television set.
Only using furniture that can safely support the television set.
Ensuring the television set is not overhanging the edge of the supporting furniture.
Not placing the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture
and the television set to a suitable support.
Not placing the television set on cloth or other materials that may be located between the television set and
supporting furniture.
Educating children about the dangers of climbing on furniture to reach the
television set or its controls.
If your existing television set is being retained and relocated, the same
considerations as above should be applied.
Buy and install low-cost anchoring devices to prevent TVs, dressers, bookcases
or other furniture from tipping.
5
CHILD SAFETY:
PROPER TELEVISION PLACEMENT MATTERS
THE CONSUMER ELECTRONICS INDUSTRY CARES
• Manufacturers, retailers and the rest of the consumer electronics industry are committed to
making home entertainment safe and enjoyable.
• As you enjoy your television, please note that all televisions – new and old- must be
supported on proper stands or installed according to the manufacturer’s recommendations.
Televisions that are inappropriately situated on dressers, bookcases, shelves, desks,
speakers, chests, carts, etc., may fall over, resulting in injury.
TUNE IN TO SAFETY
• ALWAYS follow the manufacturer’s recommendations for the safe installation of your
television.
• ALWAYS read and follow all instructions for proper use of your television.
• NEVER allow children to climb on or play on the television or the furniture on which the
television is placed.
• NEVER place the television on furniture that can easily be used as steps, such as a chest of
drawers.
• ALWAYS install the television where it cannot be pushed, pulled over or knocked down.
• ALWAYS route cords and cables connected to the television so that they cannot be tripped
over, pulled or grabbed.
WALL OR CEILING MOUNT YOUR TELEVISION
• ALWAYS contact your retailer about professional installation if you have any doubts about
your ability to safely mount your television.
• ALWAYS use a mount that has been recommended by the television manufacturer and has
a safety certification by an independent laboratory (such as UL, CSA, ETL).
• ALWAYS follow all instructions supplied by the television and mount manufacturers.
• ALWAYS make sure that the wall or ceiling where you are mounting the television is
appropriate.
Some mounts are not designed to be mounted to walls and ceilings with steel studs or
cinder block construction. If you are unsure, contact a professional installer.
• Televisions can be heavy. A minimum of two people is required for a wall or ceiling mount
installation.
MOVING AN OLDER TELEVISION TO A NEW PLACE IN YOUR HOME
• Many new television buyers move their older CRT televisions into a secondary room after the
purchase of a flat-panel television. Special care should be made in the placement of older
CRT televisions.
• ALWAYS place your older CRT television on furniture that is sturdy and appropriate for its
size and weight.
• NEVER place your older CRT television on a dresser where children may be tempted to use
the drawers to climb.
• ALWAYS make sure your older CRT television does not hang over the edge of your furniture.
CE.org/safety
6
Information importante de
sécurité et Carte de Garantie
Veuillez lire le présent manuel complètement et le garder pour
la référence future.
INFORMATION IMPORTANTE
AVERTISSEMENT
POUR REDUIRE LE RISQUE DE CHOC ELECTRIQUE, NE PAS EXPOSER LE PRODUIT A LA PLUIE OU A
L’HUMIDITE.
ATTENTION: AFIN DE RÉDUIRE LE RISQUE
DE CHOC ÉLECTRIQUE, NE PAS ENLEVER LE
COUVERCLE (OU LE DOS). CET APPAREIL NE
CONTIENT AUCUNE PIÈCE RÉPARABLE PAR
L'UTILISATEUR A L’INTERIEUR. FAIRE APPEL À
UN TECHNICIEN QUALIFIÉ.
ATTENTION:
POUR EVITER LE CHOC ELECTRIQUE, FAIRE CONCORDER LA LAME LARGE DE LA FICHE AVEC LA FENTE
LARGE, INSERER COMPLETEMENT.
AVERTISSEMENT:
Le règlement de la FCC stipule que toute modication non autorisée de cet équipement non expressément approuvés
par le fabricant pourrait annuler l'autorité de l'utilisateur à utiliser cet équipement.
ATTENTION:
Cet appareil répond aux certications FCC lorsque des câbles et des connecteurs blindés sont utilisés pour connecter
l'appareil à un autre appareil. Pour éviter les interférences électromagnétiques avec des appareils électriques tels que
les radios et les télévisions, utiliser des câbles et des connecteurs blindés pour les connexions.
INFORMATION:
Cet équipement a été testé et trouvé conforme aux limites pour un appareil numérique de classe B, conformément
à la section 15 des règles de la FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les
interférences nuisibles dans une installation résidentielle. Cet équipement génère, utilise et peut émettre de l'énergie de
fréquence radio. S'il n'est pas installé et utilisé conformément aux directives, il peut causer des interférences nuisibles
aux communications radio. Il n'existe cependant aucune garantie que ces interférences ne se produiront pas dans une
installation particulière. Si cet équipement cause des interférences nuisibles à la réception radio ou télé, ce qui peut être
établi en mettant l'équipement hors tension, on encourage l'utilisateur à tenter de remédier au problème en prenant une
ou plusieurs de ces mesures:
—
Réorienter ou déplacer l'antenne réceptrice.
—
Augmenter la distance entre l'équipement et le récepteur.
—
Brancher l'appareil à une prise sur un circuit différent de celui du récepteur.
—
Consulter le revendeur ou un technicien qualié en radio/télévision.
Radio sans l
Pour les produits disponibles sur le marché américain / canadien, seul les chaînes 1 ~ 11 peuvent être utilisées. La
sélection des autres chaînes est impossible.
Le dispositif de l'opération dans la bande 5150-5250 MHz est réservé à une utilisation intérieure an de réduire les
risques d'interférences nuisibles aux systèmes de satellite mobile à la co-chaîne.
Sélection Dynamique de Fréquence (DFS) pour les dispositifs fonctionnant dans les bandes 5250- 5350 MHz, 54705600 MHz et 5650-5725 MHz.
Cet appareil ainsi que son antenne(s) ne doit pas être co-située ni fonctionné en conjonction avec une autre antenne ou
émetteur, sauf en conformité avec les procédures de produits multi-émetteurs FCC.
Cet appareil est restreint à un usage intérieur.
Important:
Les changements ou modications non expressément approuvés par la partie responsable de la conformité pourraient
annuler l'autorité de l'utilisateur à utiliser l'équipement.
FCC Déclaration d’Exposition aux Radiations:
Cet équipement est conforme aux FCC limites d'exposition aux radiations dénies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.
Les dispositifs ne permettront pas des opérations sur les chaînes 120-132 pour 11a et 11n / a qui chevauchent la bande
5600 - 5650 MHz.
ATTENTION
RISQUE DE CHOC ÉLECTRIQUE
NE PAS OUVRIR
Le symbole d’un éclair dans un triangle
équilatéral a pour but d’avertir l'utilisateur de la
présence d'une tension dangereuse non isolée
à l’intérieur du boîtier du produit qui peut être
d'intensité suffisante pour constituer un risque
de choc électrique.
Le point d'exclamation dans un triangle
équilatéral a pour but d’avertir l'utilisateur de
la présence des instructions d'utilisation et de
maintenance (entretien) importantes dans la
documentation qui accompagne l'appareil.
1
Loading...