Hisense Electric LCDF0031 User Manual

ES-J135154-1

Barcode

REMOTE CONTROL4

Infra-red transmitter

35*10.5mm

ACCESSORIES LIST1

•

User Manual

•

Battery × 2 Screw (M5×12)

•

Quick Start Guide

•

Warranty Card

INSTALLING THE STAND2

Follow the illustrations below to complete the installation steps.

Groove

Ridge

Stand column

Base

Align the front of the stand column with the front of the base, then insert the stand column into the base making sure that the groove in the stand column aligns with the ridge in the base.

Secure the stand column to the base with 3 screws (M5×12).

•

Remote Control

55K680GW

QUICK START GUIDE

INSTALLING A WALL-MOUNT BRACKET

If you want to attach the TV to a wall-mount bracket

pre-attached (see Step 1).

Make sure the TV is laid face-down on a clean, safe, and cushioned space, remove the original screws in the bracket holes on the TV back.

NOTE: These 4 screws which got from back cover mount hole could not be used any more.

Screw (not provided)

Power on/off

Direct channel selection

Select a digital sub-channel

Launch Vudu HD Movies

Navigate Up / Down / Left / Right

or adjust OSD settings

Return to the previous menu

Media content control

Select picture mode

Display the favorite channel list

Dash button

MUTE button

Increase volume

Decrease volume

Enter TV source

MENU button

▲ /▲/

▲/

function buttons

Select sound mode

Set the sleep timer

▲

Select input source

Go to the previous channel HiMedia (Digital Media Player)

Next channel

Previous channel

Launch YouTube App Open the HiSmart Home Menu Close the menu

Open the DTV program guide (if available)

Special function buttons (see Notes)

Display the information banner ASPECT button

Adjust Closed Caption (CCD) mode Audio select button Select VGA / HDMI source

NOTE:

1. Illustrations are for your reference only.

2. Red/Green/Yellow/Cyan buttons are used for Electronic Program Guide (EPG) . After pressing the [GUIDE] button when viewing digital channels, the same color buttons will appear with explanations in the on-screen display (OSD) . Follow the steps shown in the OSD.

MAKING CONNECTIONS5

TV Side View

HEADPHONE

DIGITAL AUDIO OUT

DEBUG

USB 1

DC 5V 0.5A(MAX)

USB 3 USB 2

TV CONNECTORS7

Check the jacks for position and type before making any connections. Loose connections can result in image or color problems. Make sure that all connections are tight and secure.

Connect an outdoor VHF/UHF antenna.

ANT

VHF/UHF Antenna

Cable

ANT OUT

HDMI / COMP / AV

L -AUDIO- RVIDEO

AV IN

COMPONENT IN

L -AUDIO- RVIDEO

AV IN

COMPONENT IN

VGA & VGA AUDIO

AUDIO IN

Connect an HDMI cable or Comp/AV Adapter from an external A/V equipment.

BEST (HDMI)

BETTER (COMP)

GOOD (AV)

Connect a VGA cable and an audio cable from the PC.

TURNING THE TV ON FOR THE FIRST TIME8

4.Use Mode Next: Network Setting

Use Mode

Home mode

Retail mode

Home mode default settings are recommended

Previous Next

5.Select Network Next: Channel Search

Select Network

Wired Network

Wireless Network

Connect a wireless network with Wi-Fi

Previous Next

Skip

OPERATIONSMENU

Language setting

Country setting

Time zone setting

Use Mode

Select Network

Channel Search

Note: If you are using a cable or satellite box and you have connected it to the TV using a Coaxial cable, you should select the cable option. Be sure the cable or satellite box is turned on before starting the channel scan. If you use a cable or satellite box connected to A/V, Component or HDMI, you don't need to scan for channels.

• Please press [ENTER] to start the wizard, then press [▲/▲] button to select your language: English, Spanish or French, select [Next] to confirm enter the Welcome screen.

• In the Welcome screen introduced the available input devices and interfaces.

• Please press [▲/

• Select the local time zone according to your region.

• Daylight Saving: Set the Daylight Saving time for your area.

• Select your Mode Setting: Home Mode or Retail Mode.

• If you select Retail Mode, a message appears “Are you sure to change to retail mode?” Select “OK” to continue, or select “No” to change your selection.

• Home Mode is the recommended setting which offers full functionality of the television. If you selected Retail Mode, Energy Saving is not realized.

• The Select Network : Connect your TV to access the network.

• When the Network Setting menu opens, Hisense Service Terms and Conditions will appear. Press [◄/►] to scroll through the pages. Please read it carefully. If you want to access the internet, press the [Agree] button to set your TV’s network connections. Otherwise, press the [Disagree] button to enter the Channel search menu.

• You can setup the network configuration in this menu. For more information, Connection” and “Network Setup”

• Press [▲/▲] to select your Tuner Mode: Antenna or Cable, press [ENTER] button to confirm.

• Press [ TV automatically starts Channel Installation available in your viewing area; If you select “Skip Scan”, your TV does not scan for channels; Depending on the reception condition, it may take up to 30 minutes or more to complete memorizing channels. Please allow the process to complete without interruption.

• After scan, you will enter the complete interface. It will display all informations that you set just now and then you can press “Go” to exit the wizard.

/▲] to set the Channel Installation: Scan or Skip Scan, press [ENTER] button to confirm. If you select “Scan”, your

▲

▲ ] button to select the country where you will operate the TV.

in the user manual.

6. Channel Search

Channel Search

Please allow 30 minutes to complete.

ATV Channels added:0

DTV Channels added:0

Stop

please refer to the section titled

30%

“Network

Stand cover

Stand column

Align the stand cover with the stand column. Make sure that the bottom of the stand cover is flush against the top of the stand column.

After pre-installing the stand, secure the stand to the TV with the 4 screws (M5×12).

Secure the stand cover to the stand column with 1 screw (M5×12).

Spacer

(not provided)

Place the spacers (not provided) in the corresponding bracket holes. Follow the instructions provided with the wall-mount bracket to attach the bracket on the TV.

9.5 ~ 11.5 mm

Wall-Mount hole pattern VESA (mm)

Wall-Mount screw size (mm)

Follow instructions provided with the Wall-Mount bracket.

Bracket (not provided)

Wall-Mount Bracket

Screw SpacerThe TV's rear cover

400 × 400

• If you are not sure of your ability to do complete the installa-

tion, contact a professional installer or service technician for assistance. The manufacturer is not responsible for any damages or injuries that occur due to mishandling or incorrect assembly.

• The selected screws are 9.5 ~ 11.5 mm in length when

measured from the attaching surface of the TV's rear cover. The diameter and length of the screws differ depending on the Wall-Mount Bracket model.

PC IN

HDMI 1 (UHD)

ANT/CABLE

AUDIO

VGA

Power input

LAN

HDMI 4/ARC HDMI 3 HDMI 2

VIDEO

COMPONENT IN

TV Bottom View

AV IN

PBP

L AUDIO

SPECIFICATIONS6

55K680GWModel Name

Without Stand

Dimension (W×H×D)

With Stand

Weight

LCD Panel Minimum size (diagonal)

Screen resolution Audio power Power consumption

Power supply

Receiving systems

Receiving channels

Tuner type

Environmental conditions

Component Input VGA Input VGA (640×480 / 60 Hz), SVGA (800×600 / 60 Hz), XGA (1024×768 / 60 Hz)

HDMI Input

Without Stand

With Stand

Analog Digital

48.62 inches (1235mm)

28.22 inches (717mm)

2.32 inches (59mm)

48.62 inches (1235mm)

30.31 inches (770mm)

11.22 inches (285mm )

54.23 lbs (24.6 kg)

63.05 lbs (28.6 kg)

54.6 inches

1920 × 1080 10 W + 10 W

Power consumption 120 V ~ 60 Hz NTSC

ATSC / QAM

VHF: 2~13 UHF: 14~69 CATV: 1 ~ 125 Digital Terrestrial Broadcast (8VSB): 2 ~ 69 Digital cable (64/256 QAM): 1 ~ 135

Frequency synthesized Temperature: 41°F ~ 95°F (5°C ~ 35°C)

Humidity: 20% ~ 80% RH Atmospheric pressure: 86 kPa ~ 106 kPa

480 I / 60 Hz, 480 P / 60 Hz, 720 P / 60 Hz, 1080 I / 60 Hz, 1080 P / 60 Hz

RGB / 60 Hz (640×480, 800×600, 1024×768) YUV / 60 Hz (480 I, 480 P, 720 P, 1080 I, 1080 P)

Connect an ethernet cable to access a network or the Internet. TV

LAN

also features wireless connectivity.

LAN

DIGITAL AUDIO OUT

DIGITAL

AUDIO OUT

HEADPHONE

/AUDIO

OUT

Connect a USB device for browsing photos, music and movies.

USB

Connect Headphone for audio out of the TV.

Connect an optical cable from an external digital audio system.

LAN

Mobile Hard Disk

HELP TOPICS9

chart for problem and solution tips. If the problem cannot be resolved, please contact Hisense for additional assistance.

SYMPTOMS

No sound or picture

Picture is normal, but no sound

I have connected an external source to my TV and I get no picture and/or sound.

Network connection fail.

How do I get easy IPTV to work on my TV?

POSSIBLE SOLUTIONS

• Confirm power cord is plugged into the AC outlet and the AC outlet is getting electricity.

• Attempt to power on unit using the power button on both the TV and the Remote.

• Check the volume settings.

• Check if Mute mode is set "on" .

• Check for the correct output connection on the external source and for the correct input connection on the TV.

• Make sure you have made the correct selection for the input mode for the incoming signal.

• Check network physical connection, make sure connection is correct.

• Enter "Menu" , "Network" , "Configuration" , make sure configuration is correct according to your network service provider.

• Enter "Menu" , "Network" , "Configuration" , "Connection Test" to make sure that network connection test is successful.

• Check network physical connection, make sure connection is correct.

• Enter "Menu" , "Network" , "Configuration" , make sure configuration is correct according to your network service provider.

• Enter "Menu", "Network", "Applications", "VUDU/Netflix", "Deactivation" to reset "VUDU/Netflix" account.

• You need a broadband (high speed) Internet service with a speed of no less than 1.5 Mbps.

• Connect the TV to the internet through your router by an Ethernet Cable or wireless. If connection fails, check with your internet service provider or router manufacturer to determine if there is a firewall, content filter, or proxy settings that may block the TV from accessing the internet.

• Before calling for service, check the following information for possible solutions to problems you may experience. If none of these solutions work, turn off the TV, then turn it on again.

• Caution: Do not try to repair the TV yourself. Refer all servicing to qualified repair personnel.

ctual product.