Hisense Electric LCDC0026 User Manual

ACCESSORIES LIST1

User Manual

Scre (M5 x 12) x 4 (M4 x 12) x 5

Quick Setup Guide

Batteries: AAA × 2

Remote Control

INSTALLING THE STAND2

Follow the illustrations below to complete the installation steps.

Decorative Part

Base

Align the front of the stand column with the decorative part, then insert the stand column into the decorative part.

3 4

Secure the stand column to the base with 1 screw (M4×12).

NOTES

Product image is only for reference, actual product may vary in appearance. Carefully place your TV facedown on a soft, cushioned surface to prevent damage to the TV or scratching to the screen.

INSTALLING A WALL-MOUNT BRACKET

If you want to attach the TV to a wall-mount bracket(not provided), you should

rst remove the stand if it is pre-attached .

1. If you want to attach the TV to a wall-mount bracket (not provided), you should first remove the stand if it is pre-attached. Make sure the TV is laid face-down on a clean, safe, and cushioned surface.

2. Attach purchased bracket (1.5~2.5 mm thickness) on the TV with the 4 screws.

WARNING

To prevent internal damage to the TV and ensure the TV is mounted securely, be sure to use fixing screws (not provided) which are 9.5-12.5mm in length.

Stand Column

Insert the stand column into the base making sure that the groove in the stand column aligns with the ridge in the base. Attention the direction as image.

Secure the stand to the TV with the 4 screws (M5×12).

Bracket (1.5~2.5 mm)

A300 /A320 Series

Screws M4

9.5~12.5 mm

Wall-mount Bracket

Screw

the TV’s rear cover

Wall-Mount hole pattern VESA (mm)

Wall-Mount screw size (mm)

Follow instructions provided with the Wall-Mount bracket.

• If you are not sure of your ability to complete the installation, contact a professional

installer or service technician for assistance. The manufacturer is not responsible for any damages or injuries that occur due to mishandling or incorrect assembly.

REMOTE CONTROL

Power on/off

Select TV AV VGA

USB source

Select HDMI source

HDMI

PICTURE

Select sound mode

SOUND

Adjust closed caption mode

Used when Roku Streaming

Stick connected

CCD

FAV.CH

Display favorite list

Menu button

▲

▲/

Move Up/Down/Left

▲

/Right or adjust settings

Close the menu

Increase volume

Decrease volume

ENTER

EXIT

MUTE

VOL

CH.LIST

Direct channel

selection

Dash button select

a digital sub-channel

Media content control

function buttons

EN-22653A

CHANGE THE BATTERIES

1. Slide the back cover to open the battery compartment of the remote control.

2. Insert two AAA size batteries. Make sure to match the (+) and ( - ) ends of the batteries with the (+)and ( - ) ends indicated in the battery compartment.

3. Close the battery compartment cover.

Gently push and slide

Insert the batteries

VGA

COMPONENT

ASPECT

MTS/SAP

LAST

USB

HOME

DISPLAY

SLEEP

100 × 100

Remote sensor

Select input source

Select picture mode Select Component source

Zoom button

Audio select button Mono/ Stereo/SAP operation

Media content control function buttons

Used when Roku Streaming Stick connected

Confirm selections Display the information banner

Mute button Next channel

Previous channel

Display the channel name

Go to the previous channel

Set the sleep timer

Gently push and slide

BUTTONS AND CONNECTORS

INPUT

VOL+

VOL

AC input

USB

DC 5V 0.5A(MAX)

PC/DVI

AUDIO IN

PC IN

VIDEO

VGA

AV IN

Y P

BPR

COMPONENT IN

AUDIO

ANT/CABLEDIGITAL

AUDIO OUT

OUT

AUDIO

MHL

HDMI2 /

HDMI1 /

ARC / DVI

Item Description

INPUT

VOL+/-

(Power button)

ANT/CABLE Connect an antenna or cable TV to this jack.

HDMI

COMPONENT IN

AV IN

VGA PC/DVI AUDIO IN

/AUDIO OUT

DIGITAL AUDIO OUT

USB

Display the on-screen menu to setup your TV’s features.

Select the different input signal sources.

Adjust the volume.

Select the channel.

Turn on the TV or put the TV in standby mode.

Caution:

The TV continues to receive power even in standby mode.

Unplug the power cord to disconnect power.

HDMI (High-Definition Multimedia Interface) provides an uncompressed, all digital audio/video interface between this TV and any HDMI-device, such as a set-top box, Blu-ray disc player, or A/V receiver.

Connect to a DVD player, Digital Set-Top-Box, or other A/V devices with component (YP

PR) video and audio output jacks.

Connect to the composite video and audio (L/R) output jacks on external video devices.

Connect to a PC or other devices with a VGA or DVI interface.

Connect headphone or analog sound system using RCA Y-cable (1/8"-stereo mini to L/R phono-not provided).

Connect an audio amplifier to this jack.

Port for Digital Media Player and for software update.

TV CONNECTORS6

Check the jacks for position and type before making any connections. Loose connections can result in image or color problems. Make sure that all connections are tight and secure.

Connect an outdoor VHF/UHF antenna.

ANT

VHF/UHF Antenna

Connect a USB device for browsing photos and movies.

USB

DC 5V 0.5A(MAX)

Cable

ANT OUT

Mobile Hard Disk

HDMI / COMP / AV

Connect an HDMI cable or Comp/AV Adapter from an external A/V equipment.

Video Eect:

BEST (HDMI)

AUDIO

AV IN

COMPONENT IN

Y P

VIDEO

AUDIO

AV IN

COMPONENT IN

Y P

VIDEO

VGA & VGA AUDIO

VGA

PC IN

PC/DVI

AUDIO IN

DIGITAL AUDIO OUT

DIGITAL

AUDIO OUT

HEADPHONE

AUDIO

OUT

Connect Headphone for audio out of the TV.

BETTER (COMP)

GOOD (AV)

Connect a VGA cable and an audio cable from the PC.

Connect an optical cable from an external digital audio system.

SPECIFICATIONS7

Model Name

Without Stand

Dimension

With Stand

Weight

LCD Panel Minimum size (diagonal)

Screen resolution Audio power

Power supply

Receiving systems

Receiving channels

Tuner type

Environmental conditions

Component Input

VGA Input VGA (640×480 / 60 Hz), SVGA (800×600 / 60 Hz), XGA (1024×768 / 60 Hz)

HDMI Input

Without Stand

With Stand

Analog Digital

32A300/32A320

Width: 29 inches (737 mm) Height: 17.4 inches (442 mm) Depth: 2.37 inches (60.3 mm)

Width: 29 inches (737 mm) Height: 19.7 inches (500 mm) Depth: 7.9 inches (150 mm)

15.2 lbs (6.9 kg)

17 lbs (7.7 kg)

31.5 inches

1366 × 768 6 W + 6 W

120 V ~ 60 Hz NTSC

ATSC / QAM VHF: 2~13 UHF: 14~69 CATV: 1 ~ 125

Digital Terrestrial Broadcast (8VSB): 2 ~ 69 Digital cable (64/256 QAM): 1 ~ 135

Frequency synthesized

Temperature: 41°F ~ 95°F (5°C ~ 35°C) Humidity: 20% ~ 80% RH Atmospheric pressure: 86 kPa ~ 106 kPa

480 I / 60 Hz, 480 P / 60 Hz, 720 P / 60 Hz, 1080 I / 60 Hz

RGB / 60 Hz (640×480, 800×600, 1024×768) YUV / 60 Hz (480 I, 480 P, 720 P, 1080 I)

CY-G

Barcode 35*10.5mm

TURNING THE TV ON FOR THE FIRST TIME8

Menu Language Time Setting

Choose Your Menu Language

English

Français Español

ENTER

Enter Select

Set menu language to English,

Return

Français, or Español

EXIT

Exit

Connect your TV’s power cord to a power outlet, then press power. The initial setup screen opens. Press [

] button to

►/◄

select your language, press [ENTER] button to confirm.

Mode

Time Zone Daylight Savings Year Month Day

Time

ENTER

If Automatic, options are automatically set by TV source

Setting Time Zone:

your region.

Setting the Time: Press [▲/▲] to select the number you want to set and press [

Choose Your Time Setting

Enter Select

Select the local time zone according to

] to set.

►/◄

Return

Auto

Off

2012

January

01:10 AM

EXIT

Exit

Picture Mode TV Source

Choose Your Picture Mode

Home Mode

Retail Mode

Home mode default settings are recommended for in-home use. ENERGY STAR@ qualified.Retail mode is intended for in-store display and resets video settings at Power On.

ENTER

Enter

Reduces total power consumption

Press [

►/◄

Select Return

] to select your Picture Mode: Home Mode or

EXIT

Exit

Retail Mode, press [ENTER] button to confirm. If you select Retail Mode, a message appears “ Are you sure you want retail mode?” Select “Yes” to continue, or select “No” to change your selection. For energy saving, we kindly suggest you select the Home Mode.

ENTER

Select if using an antenna for standard or HD TV

Press [▲/▼] to select your TV Source: Antenna o r Cable, press [ENTER] button to confirm. If you press [EXIT] to exit the scanning, a message appears “Please Run Channel Auto Scan”, you should scan channels from the menu of Channels

Choose Your TV Source

Enter

Select Return

Antenna

Cable

EXIT

Exit

Note: If you are using a cable or satellite box and you have connected it to the TV using a Coaxial cable, you should select the cable option. Be sure the cable or satellite box is turned on before starting the channel scan. If you use a cable or satellite box connected to A/V, Component or HDMI, you don't need to scan for channels.

HELP TOPICS9

When there is something wrong with your TV, you can try turning o the TV and restarting it. You can also refer to the following chart

for problem and solution tips.

POSSIBLE SOLUTIONSSYMPTOMS

No sound or picture

Picture is normal, but no sound

I have connected an external source to my TV and I get no picture and/or sound.

Sound but no picture or black and white picture.

Sound and picture distorted or appear wavy.

Sound and picture is blurry or cuts out momentarily.

V] don’t work when I

[CH / set the Channel to Cable?

They work with the Air setting?

Remote control does not work.

• Confirm power cord is plugged into the AC outlet and the AC outlet is getting electricity.

• Attempt to power on unit using the power button on both the TV and the Remote.

• Check the volume settings.

• Check if Mute mode is set "on" .

• Check for the correct output connection on the external source and for the correct input connection on the TV.

• Make sure you have made the correct selection for the input mode for the incoming signal.

•

If black and white picture first unplug TV from AC outlet and replug after 60 seconds.

•

Check Color Setting if picture is black and white.

•

An electrical appliance may be affecting TV set. Turn off any appliances, if interference goes away, move appliance farther away from TV.

• I

nsert the power plug of the TV set into another power outlet.

•

If using an external antenna, check the direction, position and connection of the antenna.

•

Adjust the direction of your antenna or reset or fine tune the channel.

•

After switching to Cable, please auto program the channels. The TV will “remember” all the channels then the TV will allow you to surf the channels with [CH /V] buttons.

•

Confirm that TV still has power and is operational.

•

Change the batteries in the remote control.

•

Check if the batteries are correctly installed.

•

Clean the front of the remote control (LED window).

•

If using a universal remote, be sure to select the TV mode on the remote.

•

If the remote still does not work:

-Remove and reinstall the batteries correctly to reset the remote or install new batteries.

-Press the Power button to turn on the TV. With a universal remote if you have reset or changed the batteries you will need to reprogram the remote for the other units.

•

Check if there is obstruction between the remote control and the TV.

TIP: If you have a digital camera / camera phone, you can aim the front of the remote at camera lenses (at this time, the camera should set on camera mode, not play mode). Observe the camera screen while pressing a button on the remote control; you should see flashing light on the screen. If there is no light observed, the remote control is not working. You need to repair or replace the remote control.

Hisense Electric LCDC0026 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual